Extron MTP 15HD RS Series User Guide
Contents
1. 8 Adjust the level and peaking see Front Panel Features on page 6 9 Adjust the skew delay control see Front Panel Features on page 6 10 If applicable mount the MTPs see Mounting on page 17 MTP 15HD RS Series e Installation and Operation 5 Front Panel Features See figure 2 and the following descriptions to identify the front panel features on the transmitter and receiver MTP T 15HD RS transmitter Power LED Record LED Record button Extron MTP SERIES MTP RL 15HD RS receiver Vertical frequency DIP switch EDID select rotary switch RGB Xt LEVEL PEAKING Level control Peaking control Select button SEQ model only Red Green and Blue LEDs SEQ model only Delay skew adjustment control SEQ model only DIP switches RL receivers only Extron MTP RL 15HD RS SEQ receiver O8O00d0d0008e xt RED SELECT GREEN ek Figure 2 MTP Front Panels Q Power LED The LED indicator lights when the unit is receiving power Record LED The LED indicator flashes red during the EDID recording process to indicate a new EDID being written to memory The LED returns to a solid green after the write completes Record button The recessed record button initiates recording of the EDID of a display device connected to the loop through output to user programmable memory position O on the rotary switch Q vertical frequency DIP switch The first D2. It is possible to exceed the recommended distance but image quality may be reduced MTP 15HD RS Series e Introduction 4 Installation and Operation This section provides information on e Installation and Operation Overview e Front Panel Features e Transmitter Rear Panel Features e Receiver Rear Panel Features e Power Supply Wiring and Grounding e Twisted Pair Cable Termination e Skew Delay Compensation e EDID Configuration Installation and Operation Overview Follow the steps below to properly install and operate any of the Extron MTP 15HD RS transmitters and receivers ATTENTION Installation and service must be performed by authorized personnel Installation 1 Power off all MTPs and devices Make sure that the input sources the MTP and the output sources are all powered off and all power sources and signal cables are disconnected 2 Connect the transmitter inputs see Transmitter Rear Panel Features on page 9 3 Connect twisted pair TP cables between the MTP units see Transmitter Rear Panel Features on page 9 and Receiver Rear Panel Features on page 11 Connect the receiver outputs see Receiver Rear Panel Features on page 11 5 Configure the receiver DIP switches see Front Panel Features on page 6 6 Configure the EDID see Front Panel Features on page 6 and EDID Configuration on page 16 7 Connect the power supply and turn on all devices see Power Supply Wiring and Grounding on page 12
3. Twisted Pair MTP 15HD RS Series High Resolution Video and Serial Link MTP Transmitters and Receivers SELECT xt 50 EE EC ii ze Extron euch ae xt EV o A9 kl BLUE Be S Se Extron Extron ae M SS Bees TP RL 15HD A SEQ wu BUFFERED PRE PEAK INPUT OUTPUT lt lt MONO AUDIO rm E _ MONO AUDIO ghee a gt Extron Electronics Ze ow INTERFACING SWITCHING AND CONTROL on 68 2205 01 Rev C 0414 Safety Instructions Safety Instructions e English WARNING This symbol A when used on the product is intended to alert the user of the presence of uninsulated dangerous voltage within the product s enclosure that may present a risk of electric shock ATTENTION This symbol A when used on the product is intended to alert the user of important operating and maintenance servicing instructions in the literature provided with the equipment For information on safety guidelines regulatory compliances EMI EMF compatibility accessibility and related topics see the Extron Safety and Regulatory Compliance Guide part number 68 290 01 on the Extron website www extron com Instructions de s curit e Fran ais AVERTISSEMENT Ce pictogramme AX lorsqu il est utilis sur le produit signale a l utilisateur la pr sence a l int rieur du bo tier du produit d une tension lectrique dangereuse susceptible de provoquer un choc lectrique ATTENTION Ce pictogramme A lorsqu il est utili
4. likely to cause interference This interference must be corrected at the expense of the user NOTE This unit was tested with shielded I O cables on the peripheral devices Shielded cables must be used to ensure compliance with FCC emissions limits For more information on safety guidelines regulatory compliances EMI EMF compatibility accessibility and related topics see the Extron Safety and Regulatory Compliance Guide on the Extron website Conventions Used in this Guide Notifications The following notifications are used in this guide CAUTION A caution indicates a situation that may result in minor injury ATTENTION Attention indicates a situation that may damage or destroy the product or associated equipment NOTE A note draws attention to important information Specifications Availability Product specifications are available on the Extron website www extron com Copyright 2014 Extron Electronics All rights reserved Trademarks All trademarks mentioned in this guide are the properties of their respective owners The following registered trademarks Pl registered service marks and trademarks are the property of RGB Systems Inc or Extron Electronics Registered Trademarks AV Trac Cable Cubby CrossPoint eBUS EDID Manager EDID Minder Extron Flat Field GlobalViewer Hideaway Inline IP Intercom IP Link Key Minder Locklt MediaLink PlenumVault PoleVault PowerCage PURE3 Quant
5. MTP 15HD RS Series transmitters and receivers Tabletop Placement Under Desk and Furniture Mounting Rack Mounting Projector Mounting Tabletop Placement Attach the four provided rubber feet to the bottom of the unit and place it in any convenient location Under Desk and Furniture Mounting Mount the unit under a desk or podium using an optional Extron under desk mounting kit see www extron com To mount the unit follow the instructions provided with the mounting kit Rack Mounting UL Guidelines for Rack Mounting The following Underwriters Laboratories UL guidelines are relevant to the safe installation of these products in a rack Elevated operating ambient temperature If the unit is installed in a closed or multi unit rack assembly the operating ambient temperature of the rack environment may be greater than room ambient temperature Therefore install the equipment in an environment compatible with the maximum ambient temperature TMA 122 F 50 C specified by Extron Reduced air flow Install the equipment in the rack so that safe operation and adequate air flow is provided to the unit Mechanical loading Mount the equipment in the rack so that a hazardous condition is not achieved due to uneven mechanical loading Circuit overloading Connect the equipment to the supply circuit and consider the effect that circuit overloading might have on overcurrent protection and supply wiring Consider t
6. between them If it is shorter the wires can be easily pulled out even if tightly fastened by the captive screws Do not tin the wires Tinned wire does not hold its shape and can become loose over time Q Output connector Connect one end of a twisted pair cable to this RJ 45 female connector on the transmitter Connect the opposite end of the same twisted pair cable to the RJ 45 female connector on the receiver see Twisted Pair Cable Termination on page 14 to wire the RJ 45 connectors ATTENTION Do not connect these devices to a computer data or telecommunications network MTP 15HD RS Series e Installation and Operation 10 Receiver Rear Panel Features See figure 6 and the following descriptions to identify the rear panel features on the MTP RL 15HD RS receiver MTP RL 15HD RS BUFFERED POWER INPUT OUTPUT Figure 6 Receiver Rear Panel NOTE Control signal ground pins may be labeled as or G Audio ground pins may be labeled as or v The wiring and function are the same whichever way your product is labeled Power connector Plug the included external 12 VDC power supply into this 2 pole captive screw connector ATTENTION Before wiring the connector read the notes attentions and warnings in the Power Supply Wiring and Grounding section on the next page Input connector Connect one end of the TP cable from the transmitter or from the buffered output connector of an RL r
7. in the table on page 4 apply for a single transmitter and receiver and for a daisy chain For example the maximum suggested range for 1024 x 768 video is 200 feet 90 m with the Pre Peak switch off and 500 feet 150 m with the Pre Peak switch on whether the system consists of one transmitter and one receiver or a transmitter and three daisy chained receivers Extron recommends using at least 25 feet of twisted pair cable between the transmitter and the first receiver For daisy chained units the first receiver in the chain must be at least 100 feet 80 m from the transmitter when the Pre Peak switch is on For daisy chained units any receiver in the chain closer than 350 feet 105 m may experience some form of over peaking when the Pre Peak switch is on An overpeaked image may appear bloomed MTP 15HD RS Series e Introduction 3 Video Pre Peak Pre Peak Max Distance Max Distance Format Off On High Quality Variable Quality Composite S video Component 640x480 800x600 1024x768 1280x960 1280x1024 1360x765 1365x768 1366x768 1400x1050 1440x900 1600x1200 1920x1200 2048x1080 HDTV 720p HDTV 1080i HDTV 1080p Figure 1 Recommended Pre Peak Switch Positions and Transmission Distances at 60 Hz NOTES e Resolutions marked with an asterisk in the table above have the same range specifications at 75 Hz
8. 16 Recording a Display EDD 16 Using a Pre Programmed or User Recorded EIDA 16 Tabletop Placement aicese ee ee i7 Under Desk and Furniture Mounting 0 0 0 17 Raek MOUNINO a e e 17 UL Guidelines for Rack Moumting 17 Rack Mounting Procedure oo eee 18 Back of the Rack Mounting Procedure 18 Projector MOUNTING eriscrasii esn 18 MTP 15HD RS Series e Contents Moua Eaa E a E EE EEE VL v Introduction This section gives an overview of the user guide and describes the MTP 15HD RS series of transmitters and receivers Topics covered include e About this Guide e About the MTP Transmitters and Receivers e Transmission Distance About this Guide This guide contains installation configuration and operation information for Extron MTP transmitters and receivers that are compatible with e Extron Enhanced Skew Free AV UTP cable e Category CAT 5 5e and 6 shielded twisted pair STP unshielded twisted pair UTP or foil shielded twisted pair FTP cable This guide details the installation and operation of the following products e MTP T 15HD RS twisted pair TP transmitter e MTP RL 15HD RS receiver with loop through output e MTP RL 15HD RS SEQ receiver with loop through output and skew equalization In this guide e The term transmitter refers specifically to the MTP T 15HD RS transmitter e The term receiver refers to either of the receiver models the MTP RL 15HD RS or MTP RL 15HD RS SEQ e Th
9. HD Connector NOTES e Input only sync signals no video signals on the sync pins 13 and 14 e For component video use the R R Y and R return pins pins 1 and 6 G Y and G return pins pins 2 and 7 and B B Y and B return pins pins 3 and 8 For S video use the R R return C chroma G and G return Y luma pins e For composite video use the G pin and the associated return pin For additional genlocked video signals use the R B and associated return pins Monitor loop through output connector Connect a video monitor to this 15 pin HD connector for buffered high resolution video loop through output RS 232 connector Connect a serial communications port to this 3 5 mm 3 pole captive screw connector for bidirectional RS 232 communication Wire the connector as shown in figure 5 Connected RS 232 MTP Device Pins Pins Receive ECH IT e Tx Transmit H EI 4 Rx Ground CH O 4 G Figure 5 RS 232 Connector Wiring MTP 15HD RS Series e Installation and Operation 9 Pre Peak switch The Pre Peak switch alters the twisted pair signal output to correct for long cable runs see the table on page 4 for suggested switch settings based on the transmitted video format and transmission distance NOTES e The length of the exposed wires in the stripping process is critical The ideal length is 3 16 inches 6 mm If the exposed section is longer the exposed wires may touch causing a short circuit
10. IP switch selects the vertical frequency for the pre programmed EDID When switched to Off default position the EDID selected by the rotary positions 1 through E are based on 60 Hz When switched to On they are based on 50 Hz The second DIP switch marked Spare is not used NOTE When the EDID select rotary switch Q is in position O or F the setting of the first DIP switch is not applicable because the user recorded or attached display EDID is being used MTP 15HD RS Series e Installation and Operation 6 EDID select rotary switch The rotary switch selects specific pre programmed or user recorded EDID settings Position O of this 16 position rotary switch selects the user recorded EDID Position F passes the EDID from the display connected to the loop through output back to the input Positions 1 through E select pre programmed EDID resolutions NOTE The refresh rate of the pre programmed EDID resolutions is selected using the first DIP switch Level control The level control alters the video output voltage to affect the brightness of the displayed image Adjust the knob while viewing the displayed image to set the level that provides the best picture quality NOTE For best results when using an RL receiver connect a load to the buffered output on the receiver before adjusting the level Peaking control Peaking affects the sharpness of a picture Increased peaking can compensate for mid and high frequen
11. J 45 connectors in accordance with the TIA EIA T568A or TIA EIA T568B wiring standards You can use either standard with CAT 5 5e and 6 cable but ensure that you use the same standard on both ends of the cable Pins 12345678 AN BEE Wire color Wire color ee Joren mono audo Pa Bown eom Brem sy Insert Twisted NOTE When using Enhanced Skew Free Gei Wires AV UTP cable use the TIA EIA T568A J 45 standard only Connector Figure 8 Twisted Pair Cable Termination Diagram NOTES RJ 45 termination with CAT 5 5e or 6 cable must comply with the TIA EIA T568A or TIA EIA T568B wiring standards for all connections RJ 45 termination with Skew Free AV UTP cable must comply with TIA EIA T568A only For proper grounding of shielded twisted pair cable ensure the shield around each wire pair is all tied to the RJ 45 connectors on both ends in accordance with the connector specifications provided by the manufacturer Extron Enhanced Skew Free AV cable is not recommended for Ethernet LAN applications This cable is specially designed for compatibility with Extron Twisted Pair products that are wired using the TIA EIA T568A standard The green brown and blue wire pairs of this cable have virtually identical lengths and should be used to transmit the RGB signals The orange wire pair of this cable has a different length and should not be used to transmit the RGB signals MTP 15HD RS Series e Installation and Op
12. cuando se utiliza en el producto avisa al usuario de la presencia de importantes instrucciones de uso y mantenimiento recogidas en la documentaci n proporcionada con el equipo Para obtener informacion sobre directrices de seguridad cumplimiento de normativas compatibilidad electromagn tica accesibilidad y temas relacionados consulte la Guia de cumplimiento de normativas y seguridad de Extron referencia 68 290 01 en el sitio Web de Extron www extron com Hnucrpwvkuug no TexHuke GesonacHocTn e Pycckn NPEAYNPEKAEMUME Zanupp cumBon A ecu yka3aH Ha npogvy te npeaynpexgaeT nONb30BaTeNA O HANNYNN HEUZONMUPOBAaHHOrO ONACHOTO HANPAKEHNA BHYyTpn KOpnyca nposyKTa KOTOPOe MOxeT NpUBeCTU K NOPaXEHNIO INEKTPNYECKNM TOKOM BHMMAHME Daununp cumeson A ecnu yKagaH Ha nposykte npegynpexgaeT NONb3OBATENA O HANNYNN BadKHbIX MHCTDNKUMD no kcnnyataynn n o6cnykuBaHuto B PyKOBOACTBe npunaraeMmoM K JaHHomy O6OpyYAOBaAHNIO Ana nonyyenna nupopmaynn o npasnnax TexHnkn 6esonacHOcTn CO6NIOAEHNN HOPMATNBHbIX TpeGoOBaHN NEKTPOMATHNTHO cosmectumoctn MN 4C Bo3moxHocTn gocTyna n Apyrux Bonpocax CM PyKOBOACTBO NO 6esonacHocTu N COGNIOAEHNIO HOPMaTMBHbIX TpeGoBaHui Extron Ha Care Extron www extron com HoMep no Katanory 68 290 01 Chinese Simplified ik Ba A pa tie SAPAA RANEREN ER BE AMEER SS AeatwereeeeERRRP Ramm Mm SEET TRAE AFR ROARS BME EMEM ARATE AE GANRESHAAR Mise Extron Mit www extron c
13. cy detail loss from low bandwidth system components or capacitance in long cables The minimum setting at the counterclockwise limit provides no peaking The maximum setting at the clockwise limit provides 100 peaking Adjust this control to obtain the optimum picture sharpness NOTE To avoid possible video signal loss due to errors in the video format detection always begin with the unit set at minimal level and peaking then increase values as necessary Select button SEQ model only This recessed button selects the Red Green or Blue video signal to adjust and reset all three video signals to a skew delay of zero nanoseconds Use a small screwdriver to press and release this button to cycle among selecting the red green or blue video signal The selected signal is indicated by the red green and blue LEDs Q NOTE The SEQ receiver automatically saves the setting for the video signal that is being deselected when you push this button or when the selection times out after 10 seconds Press and hold this button for approximately 3 seconds to set the skew delay for red green and blue to zero The red green and blue LEDs all turn off Release the button 1 Red Green and Blue LEDs SEQ model only These LEDs indicate the video signal that is selected by the Select button for skew adjustment using the Delay control The LED of the selected color flashes when skew compensation for the sel
14. d units must include the serial number and a description of the problem as well as the name of the person to contact in case there are any questions Extron Electronics makes no further warranties either expressed or implied with respect to the product and its quality performance merchantability or fitness for any particular use In no event will Extron Electronics be liable for direct indirect or consequential damages resulting from any defect in this product even if Extron Electronics has been advised of such damage Please note that laws vary from state to state and country to country and that some provisions of this warranty may not apply to you Extron Headquarters Extron Europe Extron Asia Extron Japan Extron China Extron Middle East Extron Korea Extron India 1 800 633 9876 Inside USA Canada Only 800 3987 6673 65 6383 4400 81 3 3511 7655 86 21 3760 1568 971 4 299 1800 82 2 3444 1571 1 800 3070 3777 Extron USA West Extron USA East Inside Europe Only 65 6383 4664 FAX 81 3 3511 7656 FAX 86 21 3760 1566 FAX 971 4 299 1880 FAX 82 2 3444 1575 FAX Inside India Only 1 714 491 1500 1 919 850 1000 31 33 453 4040 91 80 3055 3777 4 1 714 491 1517 FAX 1 919 850 1001 FAX 31 33 453 4050 FAX 91 80 3055 3737 FAX 2014 Extron Electronics All rights reserved www extron com
15. e term SEQ receiver refers specifically to the MTP RL 15HD RS SEQ receiver with skew equalization capabilities About the MTP Transmitters and Receivers The Extron MTP T 15HD RS transmitter and MTP RL 15HD RS and MTP RL 15HD RS SEQ receivers are a system for long distance distribution of VGA or other high resolution video and RS 282 serial communications The MTPs are a part of the Extron compact line of basic distribution amplifiers switchers transmitters receivers and associated video accessories High resolution video is sent to the MTP transmitter on a 15 pin HD connector The transmitter passes RS 282 serial data or control signals on a 3 5 mm 3 pin captive screw connector The video is converted by the transmitter and RS 232 signals to proprietary signals and outputs them to the compatible MTP receiver on an RJ 45 connector The transmitter also makes the input video available for local use on a 15 pin HD connector The transmitted proprietary signal is sent to the receiver on an RJ 45 connector and is converted back into its high resolution video and mono audio components The receiver auto detects the incoming video format enabling the signal to be output on the appropriate pins of the 15 pin HD connector while the two sets of identical mono audio signals are output on a single 3 5 mm captive screw connector A series only RS series outputs on an RS 232 connection MTP 15HD RS Series e Introduction 1 The RS 232 portion of th
16. e twisted pair link e Can be bidirectional in a one receiver system that is the receiver can receive commands from the transmitter and pass RS 232 responses to the transmitter e Supports software flow control XON XOFF NOTE Hardware flow control is not supported e Supports full duplex and half duplex operation e Supports any baud rate up to 38 400 data bits parity stop bits and data format without configuration NOTE Higher rates are possible but performance will vary as a function of baud rate and twisted pair cable length The receiver also buffers the proprietary input signal and sends it to another compatible MTP receiver or to a daisy chain of receivers NOTES e The transmitter provides pre peaking which boosts the signal before it is transmitted The buffered output on the receiver does not provide any pre peaking control The total recommended distance see the table on page 4 for an entire daisy chain is the same as for a single transmitter and receiver The Pre Peak switch on the transmitter has the same effect on the recommended transmission distance for a daisy chain as for a single transmitter and receiver Up to eight receivers can be connected in series using the Buffered Output connectors provided that the total distance from the twisted pair output of the transmitter to the last receiver in the chain does not exceed the recommended distance for the resolution being used The SEQ receiver als
17. eceiver to this RJ 45 female connector Buffered output connector Connect one end of a TP cable to this female RJ 45 connector Connect the opposite end of the same TP cable from the receiver to the Input RJ 45 female connector on another receiver see Twisted Pair Cable Termination on page 14 to wire the RJ 45 connectors ATTENTION Do not connect these devices to a computer data or telecommunications network 10 5 1 6 Output video connector Connect a projector or other high OC Stee resolution video device to this 15 pin HD connector Female NOTES e The video auto detection feature is sensitive to video signals with high levels over peaked signals or both which may result in video detection issues Input only sync signals no video signals on the sync pins 13 and 14 For component video use the R R Y and R return pins pins 1 and 6 G Y and G return pins pins 2 and 7 and B B Y and B return pins pins 3 and 8 For S video use the R R return C chroma or B B return see S Video switch of on page BI G and G return Y luma pins For composite video use the G pin and the associated return pin For additional genlocked video signals use the R B and associated return pins O RS 232 connector Connect a serial communications port to this 3 5 mm 3 pole captive screw connector for bidirectional RS 232 communication Wire the connector as shown in figure 5 on page 9 MTP 15HD RS S
18. ected video signal has reached the minimum or maximum limit MTP 15HD RS Series e Installation and Operation 7 Delay skew adjustment control SEQ model only This control delays the selected red green or blue video signal by up to 62 nanoseconds The delay is applied in incremental 2 nanosecond steps Rotate the control counterclockwise to reduce the delay or clockwise to increase the delay NOTES e The control turns smoothly it does not have mechanical steps or high and low limit stops e Watch the displayed image to observe the steps of delay e The selected red green or blue LED flashes to indicate that the control has reached the minimum counterclockwise rotation or maximum clockwise rotation limit O DIP switches RL receivers only A 5 pole DIP switch configures the features of the MTP receivers e Horizontal sync H Sync switch Set this switch On up for positive horizontal sync or Off down for negative sync e Vertical sync V Sync switch Set this switch On up for positive vertical sync or Off down for negative sync NOTE Most devices use negative sync for H Sync and V Sync e S Video switch This switch sets which pins of the 15 pin HD connector S video is output on e Set this switch On up to output chroma on pin 3 and luma on pin 2 e Set this switch Off down to output chroma on pin 1 and luma on pin 2 e End Unit switch Set this switch On up if either
19. ents to whatever extent it shall deem necessary to restore said product to proper operating condition provided that it is returned within the warranty period with proof of purchase and description of malfunction to USA Canada South America and Central America Japan Extron Electronics Extron Electronics Japan 1230 South Lewis Street Kyodo Building 16 Ichibancho Anaheim CA 92805 Chiyoda ku Tokyo 102 0082 U S A Japan Europe and Africa China Extron Europe Extron China Hanzeboulevard 10 686 Ronghua Road 3825 PH Amersfoort Songjiang District The Netherlands Shanghai 201611 China Asia Middle East Extron Asia Pte Ltd Extron Middle East 135 Joo Seng Road 04 01 Dubai Airport Free Zone PM Industrial Bldg F12 PO Box 293666 Singapore 368363 United Arab Emirates Dubai Singapore This Limited Warranty does not apply if the fault has been caused by misuse improper handling care electrical or mechanical abuse abnormal operating conditions or if modifications were made to the product that were not authorized by Extron NOTE If a product is defective please call Extron and ask for an Application Engineer to receive an RA Return Authorization number This will begin the repair process USA 714 491 1500 or 800 633 9876 Europe 31 33 453 4040 Asia 65 6383 4400 Japan 81 3 3511 7655 Units must be returned insured with shipping charges prepaid If not insured you assume the risk of loss or damage during shipment Returne
20. eration 14 Skew Delay Compensation CAT 5 5e and 6 cable can lead to registration errors between the red green and blue video signals Pair skew can be measured with test equipment or identified by viewing a crosshatch test pattern with a critical eye to determine if either the red green or blue video image leads appears to the left of the other two video images NOTE Unless the twisted pair cable is changed the skew adjustment should need to be made only once during installation SEQ Receiver Skew Compensation The SEQ receiver has built in skew compensation capabilities Adjust the equalization as follows 1 Zero the skew delay for red green and blue as follows a Use a small screwdriver to press and hold the Select button for three seconds The red green and blue LEDs all go out b Release the Select button 2 Use UTP cable test equipment or examine the displayed video image with a critical eye to determine which video signal red green or blue is most shifted to the left NOTE Acrosshatch test pattern or a black background with vertical white lines is ideal for determining skew 3 Adjust the leftmost video signal as follows NOTE The SEQ receiver cannot shift the rightmost video image to the left a Use a small screwdriver to press and release the Select button until the LED lights for the left shifted color Red Green or Blue b Slowly rotate the Delay control clockwise while moni
21. eries e Installation and Operation 11 Power Supply Wiring and Grounding Figure 7 shows how to wire and ground the connector CAUTION Failure to follow these instructions may result in minor injury The two power cord wires must be kept separate while the power supply is plugged in Disconnect the power before wiring ATTENTION e Power supply voltage polarity is critical Incorrect voltage polarity can damage the power supply and the transmitter or receiver Identify the power cord negative lead by the ridges on the side of the cord To verify the polarity before connection plug in the power supply with no load and check the output with a voltmeter The length of the exposed stripped copper wires is important The ideal length is 3 16 inches 6 mm Longer bare wires can short together Shorter wires are not as secure in the connector and could be pulled out Extron twisted pair products can be adversely affected by electrostatic discharge ESD if they are not grounded correctly To prevent malfunctions or product damage an installer can correctly ground an Extron twisted pair product by following the diagram in figure 7 Ground the power port by inserting one end of the grounding wire to the negative or ground pin on the power input connector POWER 2 0 5A MAX S Rear Panel SECTION A A Power Supply Output Cord Figure 7 Power Connector Wiring and Grounding NOTE Do not tin the power s
22. he equipment nameplate ratings when addressing this concern Reliable earthing grounding Maintain reliable grounding of rack mounted equipment Pay particular attention to supply connections other than direct connections to the branch circuit Such as the use of power strips MTP 15HD RS Series e Mounting 17 Rack Mounting Procedure These units can be mounted with optional rack systems listed on the website see www extron com To mount the unit on a rack shelf follow the instructions provided with the shelf accessories Back of the Rack Mounting Procedure The MTP can be mounted to the rear of a rack using an optional back of rack mounting kit see www extron com The kit allows the product to be vertically mounted to the front or rear rack supports and facing either towards the front or the rear of the rack To mount the unit follow the instructions provided with the kit Projector Mounting Mount the unit onto a projector using an optional Extron pole mount kit To mount the unit follow the instructions provided with the pole mount kit MTP 15HD RS Series e Mounting 18 Extron Warranty Extron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purchase In the event of malfunction during the warranty period attributable directly to faulty workmanship and or materials Extron Electronics wll at its option repair or replace said products or compon
23. o corrects the skew delay commonly encountered when CAT 5 5e or 6 cables are used for RGB video component video and S video transmission NOTE An SEQ receiver should not be necessary when Extron Enhanced Skew Free AV UTP cable is used Each MTP transmitter and receiver model is shipped with an external desktop 12 VDC power supply that accepts 100 VAC to 240 VAC 50 60 Hz input Twisted Pair Cable Advantages Twisted pair cable is smaller lighter more flexible and less expensive than coaxial cable Termination of the cable with RJ 45 connectors is simple quick and economical MTP 15HD RS Series e Introduction 2 Transmission Distance The maximum distance is determined by the frequency and resolution of the signal that is input to the transmitter The table on page 4 specifies the recommended maximum transmission distances and transmitter Pre Peak switch positions see item on page 10 using Extron Enhanced Skew Free AV UTP cable or CAT 5 5e or 6 cable terminated with RJ 45 connectors NOTES e The transmitter and receiver are designed for and perform best with Extron Enhanced Skew Free AV UTP cable terminated in accordance with the TIA EIA T 568 A wiring standard CAT 5 5e and 6 cables are acceptable but less preferable We also recommend the use of pre terminated and tested cables Cables terminated on site should be tested before use to ensure that they comply with Category 5 specifications The recommendations shown
24. of the following is true e The receiver being configured is the only receiver connected to the transmitter e The receiver being configured is the last receiver in a daisy chained system Set the End Unit switch Off down on the receiver being configured if there are one or more receivers connected to the Buffered Output RJ 45 connector see on page 11 e BI 232 switch Set this switch On up for bidirectional communication or Off down for unidirectional communication MTP 15HD RS Series e Installation and Operation 8 Transmitter Rear Panel Features See figure 3 and the following descriptions to identify the rear panel features on the MTP T 15HD RS transmitter Power Connector MTP T 15HD RS Input video connector PRE PEAK Monitor loop through output connector RS 232 connector oF OUTPUT Pre Peak switch OOO O06 Output connector Figure 3 Transmitter Rear Panel NOTE Control signal ground pins may be labeled as or Q Audio ground pins may be labeled as or v Q The wiring and function are the same whichever way your product is labeled Power connector Plug the included external 12 VDC power supply into this 2 pole captive screw connector see Power Supply Wiring on page 12 to wire the connector Input video connector Connect a video source to this 15 pin HD connector for high resolution video input see figure 4 10 5 1 6 e 15 11 Female Figure 4 15 pin
25. om il Extron ZEMA antes 68 290 01 Chinese Traditional EPX Ba A zea Lem LR ZATRREAS Siet FIRES SAG Rep EBA cea tame ESI BPRS AH AMES gt EMUEME AIE TREERE Soen MARR 3872158 Extron iih www extron com 9472 Extron EER ARBTEM ERa 68 290 01 Japanese SE cons A PRE LCRMANTHSBAlS EATER NT LVL SE ri B bee SLL ae coms A mus Leer ABOMRSBI BRANT SBRORMECRT Bi eier tege Kg eg ERECT SOOTS Be OCR ART EMILEMES SI TOORA LYC LIAKOYOULI 4 bk www extron com ED Extron Safety and Regulatory Compliance Guide P N 68 290 01 SOS EL Korean e gt Sail ASE Be Bol UZER Lol Qe HZI re AHE dai AS AMS AHO ales ALEL s t aas J NEZO NSE BP FHS BA MSE Arto Ltt ai RRES YH NAS SDHC OM 7fo Eetel Al B EMuEME SHAM HEN tela HH esol Chet ALA St LHS 2 Extron 24 AbO E www extron com 2 Extron er 9 TA E LHH 68 290 01 RHE HAsAAlS FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC rules The Class A limits provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is
26. s sur le produit signale l utilisateur des instructions d utilisation ou de maintenance importantes qui se trouvent dans la documentation fournie avec le mat riel Pour en savoir plus sur les r gles de s curit la conformit a la r glementation la compatibilit EMI EMF l accessibilit et autres sujets connexes lisez les informations de s curit et de conformit Extron r f 68 290 01 sur le site Extron www extron com Sicherheitsanweisungen e Deutsch WARNUNG Dieses Symbol A auf dem Produkt soll den Benutzer darauf aufmerksam machen dass im Inneren des Geh uses dieses Produktes gefahrliche Spannungen herrschen die nicht isoliert sind und die einen elektrischen Schlag verursachen k nnen VORSICHT Dieses Symbol A auf dem Produkt soll dem Benutzer in der im Lieferumfang enthaltenen Dokumentation besonders wichtige Hinweise zur Bedienung und Wartung Instandhaltung geben Weitere Informationen Uber die Sicherheitsrichtlinien Produkthandhabung EMI EMF Kompatibilitat Zuganglichkeit und verwandte Themen finden Sie in den Extron Richtlinien f r Sicherheit und Handhabung Artikelnummer 68 290 01 auf der Extron Website www extron com Instrucciones de seguridad e Espanol ADVERTENCIA Este s mbolo A cuando se utiliza en el producto avisa al usuario de la presencia de voltaje peligroso sin aislar dentro del producto lo que puede representar un riesgo de descarga el ctrica ATENCI N Este s mbolo A
27. ted power on the display When ready to record to memory press and release the recessed record button see on page 6 to begin the recording process The Record LED see on page 6 flashes red rapidly during recording then returns to solid green after recording is completed At this time the display can be disconnected Connect the source device to the input connector Power on or restart the source device if necessary Using a Pre Programmed or User Recorded EDID 1 If you have not already done so connect the source device to the MTP 15HD transmitter Do not power on the source device at this time Set the front panel DIP switch see on page 6 to the required frequency 50 or 60 Hz Set the rotary dial see on page 7 to the required position see the table below Positions 1 through E are factory installed Position O is for user recorded EDID information Position F passes the EDID from the display connected to the loop through output directly back to the input Switch Position Resolution User recorded EDID 800x600 1024x768 default 1280x720 1280x768 1280x800 1280x1024 1360x768 1366x768 1400x1050 1400x900 1600x1200 1680x1050 1920x1080 1920x1200 Local monitor pass through CH 1 2 3 4 5 6 T 8 9 A B C D E F MTP 15HD RS Series e Installation and Operation 16 Mounting This section outlines the various mounting options available for the
28. toring the display Observe that the leftmost color shifts rightward one step at a time Continue to rotate the control until that color is properly converged NOTE A 2 nanosecond adjustment is very fine Up to 10 nanoseconds of delay may be necessary to visually detect a change in the display c Use a small screwdriver to press the Select button one more time to save the most recent adjustment or allow the 10 second time out to elapse 4 Ifthe remaining colors are left shifted repeat steps 2 and 3 Non SEQ Receiver Skew Compensation Try the following methods to minimize or eliminate pair skew e Switch to Extron Enhanced Skew Free AV UTP cable e Add askew compensation cable equal to the length of pair skew to the output of the receiver e Install an SEQ 100 15HD Skew Equalizer to the video output of the receiver and adjust the skew for the leading video image MTP 15HD RS Series e Installation and Operation 15 EDID Configuration The MTP 15HD RS transmitter can either record EDID from a display device or a pre programmed EDID can be selected using the rotary and DIP switches Recording a Display EDID 1 4 Turn the rotary switch to position 0 NOTE The vertical frequency DIP switch has no effect in this mode Connect the display device to the local monitor output connector NOTE The MTP 15HD transmitter should be supplying the necessary 5 VDC to power on the display However to ensure that EDID is being transmit
29. um SoundField SoeedMount SpeedSwitch System INTEGRATOR TeamWork TouchLink V Lock VersaTools VN Matrix VoiceLift WallVault WindoWall XTP and XTP Systems Registered Service Mark S3 Service Support Solutions Trademarks AAP AFL Accu Rate Frame Lock ADSP Advanced Digital Sync Processing Auto lmage CDRS Class D Ripple Suppression DDSP Digital Display Sync Processing DMI Dynamic Motion Interpolation Driver Configurator DSP Configurator DSVP Digital Sync Validation Processing FastBite FOXBOX IP Intercom HelpDesk MAAP MicroDigital ProDSP QS FPC QuickSwitch Front Panel Controller Scope Trigger SIS Simple Instruction Set Skew Free SpeedNay Triple Action Switching XTRA ZipCaddy ZipClip Contents Introduction sis cceccccesscceccevevuncacsscenscsncsecense 1 AD OUEtIS GIGS a E 1 About the MTP Transmitters and Receivers 1 Twisted Pair Cable Achamtages 2 TrANSMISSION DISTANCE cceeeeseeceeeseeeeeeeeeeeeaes 3 Installation and Operation stees enen 5 Installation and Operation Overview 5 Astala ineine oa 5 Front Panel Features 6 Transmitter Rear Panel Features 9 Receiver Rear Panel Features 11 Power Supply Wiring and Grounding 12 Twisted Pair Cable Termination cc0c 14 Skew Delay Compensaton sesser 15 SEQ Receiver Skew Compensation 15 Non SEQ Receiver Skew Compensation 15 EDID COnmQuIratlON seisto tinaasan disen
30. upply leads before installing in the captive screw connector Tinned wires are not as secure in the connectors and could be pulled out of the connector MTP 15HD RS Series e Installation and Operation 12 ATTENTION e This product is intended to be supplied by a Listed Power Unit marked Class 2 or LPS rated 12 VDC maximum 1 0 A Always use a power supply supplied or specified by Extron Use of an unauthorized power supply voids all regulatory compliance certification and may cause damage to the supply and the end product e The installation must always be in accordance with the applicable provisions of National Electrical Code ANSI NFPA 70 article 725 and the Canadian Electrical Code part 1 section 16 The power supply shall not be permanently fixed to building structure or similar structure Unless otherwise stated the AC DC adapters are not suitable for use in air handling spaces or in wall cavities The power supply is to be located within the same vicinity as the Extron AV processing equipment in an ordinary location Pollution Degree 2 secured to the equipment rack within the dedicated closet podium or desk As an alternative an Extron PS 124 Universal 12 VDC Power Supply can power multiple MTPs or other Extron 12 VDC devices using only one AC power connector MTP 15HD RS Series e Installation and Operation 13 Twisted Pair Cable Termination Figure 8 details the recommended termination of twisted pair cables with R
Download Pdf Manuals
Related Search