BlackDiamond Module Install Note Rev B
Contents
1. BlackDiamond Module Installation Note All BlackDiamond modules Management Switch Fabric Modules MSM64i and I O modules are hot swappable You do not need to power off the system to remove or insert a module a Caution Service to BlackDiamond modules should be performed by trained service personnel only Before installing or removing any components of the system or before carrying out any maintenance procedures you must read the safety information provided in Appendix A of the Extreme Networks Consolidated Hardware Guide a Warning Blank panels must be installed in empty slots to ensure adequate system A z A cooling Installing a Module To install a module 1 Select a slot for the module e If you are installing an MSM64i module the module slides into one of the following lettered orange slots Slots A through D in the BlackDiamond 6816 Slots A through B in the BlackDiamond 6808 e If you are installing an I O module the module slides into one of the following numbered slots Slots 1 through 16 in the BlackDiamond 6816 Slots 1 through 8 in the BlackDiamond 6808 a Caution You can install the MSM64i only in slots A through D in the BlackDiamond 6816 or slots A through B in the BlackDiamond 6808 You can install I O modules only in slots 1 through 16 in the BlackDiamond 6816 or slots 1 through 8 in the BlackDiamond 6808 I O modules do not fit in slots A B C or D Blank panels can be installe2. modules Otherwise you might unseat modules that you have not secured 8 Store the module packaging for future use 9 Repeat this procedure for additional modules if applicable 10 Leave the ESD strap permanently connected to the chassis so that it is always available when you need to handle ESD sensitive components Removing a Module To remove a a module 1 Attach the ESD strap that is provided to your wrist and connect the metal end to the ground receptacle that is located on the top left corner of the switch front panel 2 Use a 1 Phillips screwdriver to unscrew the two captive screws Simultaneously rotate the ejector injector handles outward to disengage the module from the backplane as shown in Figure 1 Blank panels do not have ejector injector handles because they do not engage the backplane EW_clips2 Figure 1 MSM64i showing extended ejector injector handles 4 Slide the module out of the chassis 5 If you are not going to install a replacement module cover the slot with a blank faceplate Otherwise follow the module installation procedure on page 1 6 Repeat this procedure for additional modules if applicable 7 Leave the ESD strap permanently connected to the chassis so that it is always available when you need to handle ESD sensitive components BlackDiamond Module Installation Note 2
3. d in any slot Forceful insertion can damage the module or the backplane connectors A Note If two or more MSM64is are installed and the master MSMG64i is removed the Ar BlackDiamond automatically reboots This causes the slave MSM64i to become the Master MSM64i 2 Attach the ESD strap that is provided to your wrist and connect the metal end to the ground receptacle that is located on the top left corner of the switch front panel 3 Remove the blank faceplate from the slot if applicable Part Number 121002 00 Rev B 1 Removing a Module 4 For the BlackDiamond 6816 ensure that the module is horizontal with the module name to the left and that the ejector injector handles are extended For the BlackDiamond 6808 ensure that the module is vertical with the module name at the top and that the ejector injector handles are extended 5 Slide the module into the appropriate slot of the chassis until it makes contact with the backplane a Caution Ensure that the sheet metal of the module and not the PCB board engages the card cage runners As the module begins to seat in the chassis the ejector injector levers begin to close 6 Use one hand to hold the module in place and your other hand to close the ejector injector levers by pushing them toward the center of the module 7 To secure the module tighten the two captive screws using a 2 Phillips screwdriver a Note Tighten the screws of this module before you insert additional
Download Pdf Manuals
Related Search