Installation & Operation Guide
Contents
1. Attach the buttons to the keypad 1 Arrange the button caps in position on the rear housing assembly according to the program plan 2 Carefully position the bezel over the button caps on the rear housing assembly 3 Install and tighten the two supplied 2 28 x 3 16 screws 4 Press and release each button to ensure that the button caps move freely Assembling the Keypad C2N CBD P Shown Light Sensor C2N CBD P Only LED Holes Screws 2 2 28 x 3 16 y t Assembling the Keypad C2N CBF P Shown Light Sensor LED Holes Screws 2 2 28 x 3 16 Assembling the Keypad C2N CBV P Shown Light Sensor LEDs LED Holes Screws 2 2 28 x 3 16 4 Bezel Hardware Hookup CAUTION Turn the Cresnet system power off before making connections Do not turn the system power on until the device is fully installed in the mounting surface When making terminal block connections strip the ends of the wires approximately 1 4 in 6 mm Use care to avoid nicking the conductors Twist together the ends of the wires that share a connection Apply solder only to the ends of the twisted wires Avoid tinning too far up the wires or the end becomes brittle Make connections to the NET and INPUT ports e Using the supplied 4 pin2. and trade names may be used in this document to refer to either the entities claiming the marks and names or their products Crestron disclaims any proprietary interest in the marks and names of others Crestron is not responsible for errors in typography or photography This document was written by the Technical Publications department at Crestron 2015 Crestron Electronics Inc Crestron Electronics Inc 15 Volvo Drive Rockleigh NJ 07647 Tel 888 CRESTRON Fax 201 767 7576 www crestron com Installation amp Operation Guide DOC 7063G 2028549 05 15 Specifications subject to change without notice
3. 11 2 in 39 mm 1 3 4 in 45 mm 3 5 16 in 85 mm 2 Holding the keypad with the LEDs on the left place it in the hole The spring clamp holds the keypad in position Turn the Cresnet system power on Mounting the C2N CBF Keypad NOTE If the keypad needs to be removed from the mounting surface use a small flat blade screwdriver to carefully pry the keypad away from the mounting surface Without damaging the keypad or mounting surface gently remove the keypad Vimar Mount Installation After the Cresnet network wiring has been installed and verified install the keypad in the Vimar style electrical box NOTE Ensure that Cresnet power is off until the keypad is fully installed Troubleshooting The following table provides corrective actions for possible trouble situations If further assistance is required please contact a Crestron customer service representative Holding the keypad with the LEDs on the left place it in the Vimar style electrical box The keypad snaps into place Turn the Cresnet system power on Make sure all excess wire is completely inside the electrical box and not between the box and the keypad CAUTION Excess wire pinched between the keypad and electrical box could short out Mounting the Keypad in a Vimar Style Electrical Box Ambient Light Sensor Operation The C2N CBD P C2N CBD P KP C
4. 2N CBF P and C2N CBV P keypads have an ambient light sensor that can be used to automatically configure the backlight to operate in either Day mode or Night mode Backlight operation is based on ambient light level and a programmed threshold Presets based on the keypad color set the optimum backlight level for Day mode and Night mode When using presets the following occurs e For light colored keypads with dark engraving the backlight turns on dim when in Night mode and off when in Day mode e For dark colored keypads the backlight turns on dim when in Night mode and on bright when in Day mode NOTE Backlight levels can also be set manually The indicator LEDs automatically adjust their brightness based on ambient light going bright when the keypad is well lit and going dim when the room is dark When two or more keypads are to be installed side by side ensure that the backlights on all units are in sync To do this there are signals available on the programming symbol to allow one unit to act as the master backlight controller and the rest as slaves Refer to the Crestron Studio or SIMPL Windows help file for more information TROUBLE POSSIBLE CAUSE S CORRECTIVE ACTION The keypad does not function The wrong power supply is being used Use a Crestron power supply The unit is not receiving power or it is receiving insufficient power Verify the cable plugged into the NET port is secure Ve
5. C2N CBD P C2N CBD P KP C2N CBD E C2N CBF P C2N CBV P Cameo Keypads Installation amp Operation Guide The Cameo keypads from Crestron present a fresh innovative concept in keypad design featuring a highly configurable 1 gang wall mount form factor that is at once inviting to the touch and appealing to the eye The C2N CBD P C2N CBD P KP C2N CBD E C2N CBF P and C2N CBV P easily install alongside other low voltage in wall devices to deliver a fully customizable keypad control solution as part of a complete Crestron control system The C2N CBD P C2N CBD P KP C2N CBD E C2N CBF P and C2N CBV P are unctionally identical For simplicity within this guide the term C2N CBD CBF CBV is used except where noted Specifications SPECIFICATION Power Requirements DETAILS Cresnet Power Usage 1 W 0 05 A 24 Vdc Environmental Temperature 32 F to 113 F 0 C to 45 C Humidity 10 to 90 RH non condensing Heat Dissipation 3 4 Btu h Weight Standard Mount 3 oz 64 g Flush Mount 3 oz 75 9 Vimar Mount 2 oz 50 g Additional Resources Visit the product page on the Crestron website www crestron com for additional information and the latest firmware updates C2N CBD P C2N CBD P KP C2N CBV P Assemble the Keypad NOTE The C2N CBD P KP comes pre assembled with either ON and OFF buttons or SCENE 1 to 4 UP DOWN and OFF buttons The devices do not come with extra button caps
6. against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Industry Canada IC Compliance Statement CAN ICES 3 A NMB 3 A The product warranty can be found at www crestron com warranty The specific patents that cover Crestron products are listed at patents crestron com Crestron the Crestron logo Cameo Cresnet and Crestron Toolbox are either trademarks or registered trademarks of Crestron Electronics Inc in the United States and or other countries UL and the UL logo are either trademarks or registered trademarks of Underwriters Laboratories Inc in the United States and or other countries Other trademarks registered trademarks
7. connector connect the Cresnet cable to the NET port of the keypad e Using the supplied 3 pin connector all except C2N CBD E connect the contact closure input cable to the INPUT port of the keypad Hardware Hookup NET To Control System or Other Network Devices INPUT From Contact Closure Not Available on C2N CBD E CRESTRON MAEUE O NOTES Observe the following points e This product should be installed and used in accordance with appropriate electrical codes and regulations e This product should be installed by a qualified electrician NOTE Before using the C2N CBD CBF CBV ensure the device is using the latest firmware Check for the latest firmware for the C2N CBD CBF CBV at www crestron com firmware Firmware is loaded onto the device using Crestron Toolbox The C2N CBD CBF CBV can be installed into an electrical box C2N CBD P C2N CBD P KP C2N CBD E flush mounted C2N CBF P or installed into a Vimar box C2N CBV P Refer to the appropriate procedure below Electrical Box Installation After the Cresnet network wiring has been installed and verified use the following procedure to install the keypad in a standard 1 gang electrical box 1 Holding the keypad with the LEDs on the left place it in the electrical box 2 Secure the keypad using the included 6 32 x 3 4 screws CAUTION Excess wire pinched between the keypa
8. d and electrical box could short out Make sure all excess wire is completely inside the electrical box and not between the box and the keypad Mounting the Keypad in a 1 Gang Electrical Box Screws 2 6 32 x 3 4 3 Attach the desired decorator style faceplate not supplied 4 Turn the Cresnet system power on Flush Mount Installation After the Cresnet network wiring has been installed and verified install the keypad in the prepared hole 1 Use the supplied template as a guide to cut the mounting hole for the C2N CBF P Ensure that the template is level and properly located on the wall The keypad does not offer a means of adjusting the keypad in the opening The following illustration not to scale shows the dimensions of the cutout template NOTE Be very careful when cutting the hole There are no adjustments for alignment with the spring clamp The optional MMK G1 CBF T Mud Ring Mount Kit for Cameo Flush Mount Keypads sold separately may be used if the cutout in the mounting surface is too large for the keypad Cutout Template Not to Scale TEMPLATE OV40096 FOR C2N CBF 5 3 5 in 137 mm THIS PIECE IS FOR CENTER LINE REFERENCE ONLY DO NOT USE THIS PIECE ASA CUTTING TEMPLATE 3 1 4 in 83 mm 2 7 8 in 73 mm w z a a T 9 _ Zz 2 b Oo A Le CUT ALONG THIS LING CLEARANCE AREA FOR BEZEL
9. rify that the power supply is correct There is a loose connection in the network Verify the cable plugged into the NET port is secure The keypad does not function All six feedback LEDs are on low The wrong Net ID is being used Verify that the C2N CBD CBF CBV s Net ID matches the Net ID in the software program The keypad does not function or does not function as expected However it reports on Cresnet at the proper Net ID The unit is not programmed correctly Use SIMPL Debugger to check the behavior when buttons are pressed Revise and reload the program as needed to correct the behavior This product is Listed to applicable UL Standards and requirements by Underwriters Laboratories Inc cus Federal Communications Commission FCC Compliance Statement This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation CAUTION Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user s authority to operate the equipment NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection
Download Pdf Manuals
Related Search