Installation Instructions - Pdfstream.manualsonline.com
Contents
1. fuse or oven circuit breaker before beginning installation to avoid severe or fatal shock injury CAUTION For personal safety the mounting surface must be capable of supporting the cabinet load in addition to the added weight of the 75 pound product plus additional oven loads of up to 50 pounds or a total weight of 125 pounds CAUTION For personal safety this product cannot be installed in cabinet arrangements such as an island a peninsula or below a countertop MISE EN GARDE Pour votre s curit personnelle retirez les fusibles de la maison ou le disjoncteur du four avant l installation pour viter des blessures graves ou m amp me le d ces pouvant tre cause par un choc lectrique MISE EN GARDE Pour votre s curit personnelle la surface de montage doit tre capable de supporter le poids du cabinet en plus du poids suppl mentaire du produit soit 34 kg en plus du poids supplementaire du four pouvant aller jusqu 22 7 kg ou un poids total de 56 7 kg MISE EN GARDE Pour votre s curit personnelle ce produit ne peut tre installe dans des arrangements d armoires dont un lot une p ninsule ou le dessous d un comptoir Installation Instructions Step 1 Slide the Oven into the Cutout Step 2 Install Bottom Trim Step 3 Install Side Trim Step 4 Install Mounting Screws Step 5 Finalize Installation Design Information MODELS AVAILABLE Profile Models Monogram Models S2. CB1000 WW White ZSC1000 BB Black SCB1000 BB Black ZSC1001 SS Stainless Steel SCB1000 CC Bisque SCB1001 SS Stainless Steel PRODUCT DIMENSIONS AND CLEARANCES 29 3 4 With Optional Side Trim 22 9 16 1 1 8 26 3 4 21 1 2 aa eo 13 p In 1 1 16 13 16 NOTE Appearance may vary slightly by model TOOLS REQUIRED PARTS SUPPLIED e 2 Phillips screwdriver e 6 Brass screws 3 required 3 extra e Hand held drill e 5 Color matched screws 4 required 1 extra e High speed drill bit 1 8 diameter e 2 Side trim pieces e 3 8 slot head screwdriver e Bottom Trim Design Information ADVANCE PLANNING e These ovens may be installed directly into a 27 or 30 wide oven cabinet e The front surface of the oven will be nearly flush with Surrounding cabinetry doors e This oven can be installed over any GE or GE Monogram single electric built in oven or a warming drawer or both e Color matched side trim pieces are provided for installation into a 30 wide space Use the side trim when Installing the oven above a 30 wide wall oven or warming drawer Discard the side trim pieces If you are installing over a 27 wide oven e Cutout dimensions are the same for both 27 or 30 wide cabinet installations IMPORTANT This oven is not approved for use above another built in Speedcook oven a side by side installation or below a countertop e For personal safety this oven cannot be instal
3. E Deux personnes sont n cessaires pour soulever le four et linserer dans l ouverture Saisissez le par le dessous a l avant et a l arri re N UTILISEZ PAS LA POIGNEE POUR SOULEVER LE FOUR DES DOMMAGES SE PRODUIRONT e Lift and hold the oven at the front of the opening Hold the oven at a 45 angle and plug in the power cord e Carefully slide the oven into the cabinet part way Leave the oven a few inches forward of the cabinet frame e Check to be sure the power cord is not trapped under the oven or along the sides of the oven STEP 2 INSTALL BOTTOM TRIM e Align bottom trim tabs to slots in the bottom of the oven oo e Secure the bottom trim to the bottom of the oven using 3 brass screws provided Installation STEP 3 INSTALL SIDE TRIM FOR 30 CABINET INSTALLATION ONLY SKIP THIS STEP IF YOU HAVE 27 WIDE CABINETRY e Open the oven door e Hang the side trim pieces on the tabs behind the oven flange The screw holes in the side trim should align with the holes in the oven flange e Check to be sure the oven is pushed back into the opening and against the cabinet frame INSTALL MOUNTING SCREWS e Drill pilot holes through the side flanges 2 on each side e Drive the color matched screws into the side flange and side trim if applied STEP 5 FINALIZE INSTALLATION e Turn power on atthe source The interior light shoul
4. Installation Instructions Advantium 120 Built In SpeedCook Ovens SCB1000 SCB1001 ZSC1000 ZSC1001 For a Spanish version of this manual visit our Website at ge com Para consultar una version en espa ol de este manual de instrucciones visite nuestro sitio de internet ge com Safety Information BEFORE YOU BEGIN Read these instructions completely and carefully O IMPORTANT Save these instructions for local inspector s use e IMPORTANT observe all governing codes and ordinances e Note to Installer Be sure to leave these instructions with the Consumer e Note to Consumer Keep these instructions with your Owner s Manual for future reference Skill Level Installation of this appliance requires basic mechanical and electrical skills Completion time 1 hour Proper installation is the responsibility of the installer Product failure due to improper installation is not covered under the Warranty See Owner s Manual for warranty information IMPORTANT e Use this oven only for its intended purpose e Never use the oven for warming or heating a room Prolonged use of the oven without proper ventilation can be hazardous CONTENTS Design Information Models Available Product Dimensions and Clearances Tools Required Parts Supplied Advance Planning Installation Preparation Electrical Requirements Prepare the Opening Remove the Packaging CAUTION For personal safety remove house
5. ates with a standard three prong grounding wall receptacle to minimize the possibility of electric shock The customer should have the wall receptacle and circuit checked by a qualified electrician to make sure the receptacle is properly grounded and has the correct polarity e Where a standard two prong wall receptacle is encountered it is the personal responsibility and obligation of the customer to have it replaced with a properly grounded three prong wall receptacle Do not under any circumstances cut or remove the third ground prong from the power cord DO NOT USE AN EXTENSION CORD Installation Preparation PREPARE THE OPENING The Advantium 120 can be installed in combination with other GE Monogram appliances Always follow each products Installation Instructions to complete the installation Single Advantium 120 Installation Order a 27 or 30 wide single oven cabinet or cut the opening in a wall to the dimensions shown 27 or 30 23 1 2 Construct Base Min 3 8 Plywood Supported 36 3 4 by 2x 4 Min or1x2 Runners all Four Sides e Always maintain 36 3 4 minimum height from the floor to the cutout in any single or combined installation e Allow 1 1 4 case trim overlap at the top and 7 8 overlap on the bottom and each side of the opening e Oven overlaps will conceal cut edges on all sides of the opening When installed over a single oven or a warming drawer allow at least 2 betw
6. d come on when the door is opened e Refer to the Owner s Manual for operating instructions Notes 10 Notes 11 NOTE While performing installations described in this book safety glasses or goggles should be worn NOTE Product improvement is a continuing endeavor at General Electric Therefore materials appearance and specifications are subject to change without notice Pub No 49 40459 1 GE Consumer amp Industrial Appliances 07 05 JR General Electric Company P No 3828W 5U0445 Louisville KY 40225 Printed in Korea 2005 General Electric Company
7. een the two openings This separation will provide clearance for bottom overlap of the Advantium 120 and the other appliance overlaps Construct a solid oven floor of 3 8 min thick plywood supported by 2 x 4 runners on all sides e The support must be level and rigidly mounted flush with the bottom edge of the cutout PREPARE THE OPENING conr Installation over a GE Monogram Warming Drawer 27 or 30 23 1 2 Construct Solid Bottom Min 3 8 Plywood Supported i by 2 x 4 or 25 1 8 1x2 Runners all Four Sides Install2x 4 or2x2 Runners or Solid Bottom 36 3 4 Must Min Support 100 Ibs NOTE Additional clearances between the cutouts may be required Check to be sure the oven supports above the Warming Drawer location does not obstruct the required interior depth and height See Warming Drawer installation instructions for details Installation Preparation PREPARE THE OPENING conr Installation over a GE Monogram Oven 23 1 2 Construct Solid Bottom Min 3 8 Plywood Supported by 2x4or1 x 2 Runners all Four Sides 27 or 30 Per Oven Requirement 45 1 4 Min If you are replacing a GE Monogram electric double oven with the combined installation of an Advantium 120 and a single oven use the dimensions shown The middle rail separating the two openings may need to be larger than the 2 minimum shown PREPARE THE OPENING conr Installation o
8. led in a cabinet arrangement such as an island or peninsula e The oven must be installed at least 36 3 4 above the floor e Allow for clearance to adjacent corners walls drawers etc e Cabinets installed adjacent to wall ovens must have an adhesion spec of at least 194 temperature rating The oven must be securely installed in a cabinet that is firmly attached to the house structure Weight on the oven door could cause the oven to tip and result in injury Never allow anyone to climb sit stand or hang on the oven door Installation Preparation ELECTRICAL REQUIREMENTS Single Advantium 120 Installation This product requires a 120 volt 60 Hz 15 amp circuit and draws 1 8 kilowatts This product must be connected to a supply circuit of the proper voltage and frequency e Wire size must conform to the requirements of the National Electrical Code or the prevailing local code for this kilowatt rating e The power supply cord and plug should be brought to a separate 15 or 20 ampere branch circuit single grounded receptacle The outlet box should be located within reach of the 48 power cord ELECTRICAL LOCATION Locate outlet box in the shaded area Install a recessed electrical outlet in the back wall of the opening within 6 of either side and at least 9 above the cutout floor IMPORTANT Please read carefully The power cord of this appliance is equipped with a three prong grounding plug that m
9. ver a GE Monogram Oven and Warming Drawer a 9 9 olid one Bottom Min 3 8 Plywood Supported by2x4or1 x 2 Runners all Four Sides 2 Min 27 or 30 i Per Oven Requirement on na 45 1 4 2 un Sr K KX NOTE Additional clearances between the cutouts may be required Check to be sure the oven supports above the Warming Drawer location does not obstruct the required interior depth and height See Warming Drawer installation instructions for details CAUTION For personal safety the mounting surface must be capable of supporting the cabinet load in addition to the added weight of this approximate 75 pound product plus additional oven loads of up to 50 pounds or a total weight of 125 pounds MISE EN GARDE Pour votre s curit personnelle la surface de montage doit tre capable de supporter le poids du cabinet en plus du poids suppl mentaire du produit soit 34 kg en plus du poids suppl mentaire du four pouvant aller jusqu 22 7 kg ou un poids total de 56 7 kg REMOVE THE PACKAGING e Lift the oven out of the carton e Remove all packing material and tape e Open the door and remove parts box e Locate parts package containing mounting screws Installation STEP 1 SLIDE THE OVEN INTO THE CUTOUT CAUTION Two people are required to lift the oven into the opening Grasp the bottom at the front and rear DO NOT USE THE HANDLE TO LIFT THE OVEN DAMAGE WILL OCCUR MISE EN GARD
Download Pdf Manuals
Related Search