DM240XR Firmware Upgrade Procedure AN208
Contents
1. DM240XR Firmware Upgrade Procedure AN208 Rev 1 0 M RADYNE P 4 Radyne Corporation e 3138 E Elvvood St e Phoenix AZ 85034 e 602 437 9620 e Fax 602 437 4811 AN208 Rev 1 0 DM240XR Firmware Upgrade DM240XR Firmware Upgrade Procedure AN208 Record of Revisions Radyne Corporation is constantly improving its products and therefore the information in this document is subject to change without prior notice Radyne Corporation makes no warranty of any kind with regard to this material including but not limited to the implied warranties of merchantability and fitness for a particular purpose No responsibility for any errors or omissions that may pertain to the material herein is assumed Radyne Corporation makes no commitment to update nor to keep current the information contained in this document Radyne Corporation assumes no responsibility for use of any circuitry other than the circuitry employed in Radyne Corporation systems and equipment Revision Reason for Change Level 08 29 07 Initial Release Revision Approval Engineering Approval Production Approval Level Printed Name Date and Signature Printed Name Date and Signature a AN208 Rev 1 0 DM240XR Firmware Upgrade DM240XR Firmware Upgrade Procedure 1 0 Introduction The purpose of this document is to provide the instructions for the manual firmware upgrade of the DM240XR Modulator 2 0 Required Items 1 PC with t2. a ETHERNET ASI Figure 3 Memory Card with Latch in Down position The next time the DM240XR is powered up it will contain the new firmware The new firmware can be verified on the front panel at power up or by looking in the SYSTEM HW FW CONFIG M amp C REV menu The new firmware will read F05377 xx where xx is the latest revision of software Page 2
3. he following a Compact Flash Programmer b Unzip Program including but not limited to such as winzip or winrar 3 0 Procedure Manual Compact Flash Programming 1 Locate the power switch at the rear of the unit and shut off power 2 Gently remove the Compact Flash Memory Card by lifting the Compact Flash Memory Card Latch up and pulling gently on the Card to remove it located in the rear of the unit MADE IN USA EXT REF IN pele Four BAND a q a aon Al AEK OUT 7 ko gal EJ Ate ETHERNET ASI Compact Flash Figure 1 Location of Compact Flash card on the DM240XR E SHZIOO 240 VAC LA U s si h bi pt E L e ca ST e i o pP v d 1 l a r dar ETHE lt INE ri Figure 2 Memory Card vvith Latch in Up position 3 Connect the USB Compact Flash Reader Programmer to your computer USB port Note DM240XR firmware is distributed as a zip file via e mail FTP download or compact disk The name of the file is typically mc zip Page 1 AN208 Rev 1 0 DM240XR Firmware Upgrade 4 10 11 12 13 Create a folder on your computer s hard drive named DM240XR rev xx where xx is the latest revision of firmware for example DM240XR rev H Copy the attached mc zip file to that newly created folder Also create a folder called DM240XR rev yy where y is the previous revision of firmware to store the previous revision in the event that it is needed la
4. ter Extract the zip file into the DM240XR rev xx folder The zip file will extract into a folder called DM240XR rev xx MC This folder contains the DM240XR firmware image Insert the compact flash into the Compact Flash Reader Programmer The compact flash will appear as a regular drive on your computer The easiest way to find the compact flash drive is to use windows explorer and look under My Computer Use the windows explorer to open the compact flash drive A directory called MC will be visible Copy the old MG folder with drag and drop into the DM240XR rev yy folder on your hard drive to back up the old firmware revision Erase the contents of the compact flash card by selecting the MC directory in the root of the compact flash card and deleting it and all sub folders Copy the DM240XR rev xx MC onto the compact flash by dragging and dropping the MC directory in DM240XR rev xx select the MC directory only and dragging the MC directory onto the compact flash drive Wait a few moments while the Compact Flash Reader Programmer writes to the compact flash The LED on the reader programmer will flash for several seconds Wait for approximately 30 seconds after the last flash then remove the compact flash card from the reader and insert it in to the DM240XR as Shown in Figure 3 and gently press until fully seated Move the retaining clip over the end of the compact flash card As shown in Figure 3 14 0 3
Download Pdf Manuals
Related Search