Digisystem Programmer DT05
Contents
1. adjust all parameters in the DT05 and then select Send all on the DT05 menu The Receiver DT10 must be set to pairing mode When using the Programmer DT05 for configuring the distance between the Programmer DTO5 and the Receiver DT10 should not exceed 0 5 meters To listen to a DT 10 plug it into the socket on the programmer and connect headphones or a neck loop Menu control a Scroll up a Press select g Scroll down To access the menu press the menu control and then scroll up or down Press the menu control to select Programmer D105 6 Menu in the Programmer DT05 R enable R R M enable R M Tone ind Auto sleep Pairing Always on Send all Settings Language Factory Reset About Back relates to both the main menu and submenus Here you can choose to return to the menu and to the main display R enable Enables selection of R mode with the push button on the Receiver DT10 R Adjusts the output level of the Receiver DT10 when using R mode R M enable Enables selection of R M mode with the push button on the Receiver DT10 R M Adjusts the output level of the Receiver DT10 when using R M mode Tone ind Activates acoustic indication tones when selected Indication for pairing mode and pairing is always heard even If Tone ind is disabled Auto sleep When Auto sleep is enabled the Receiver DT 10 goes into sleep mode if the Digisystem Microphone transmit ter is turned off This2. output gt 130 dB SPL Sound Pressure Level Could be very dangerous for your hearing It is recommended that customers keep the volume control in the lowest position when turning on the device If not the sound could potentially cause harm to the customers hear ing Comfort Audio is not liable for damages arising from usage of the equipment not in accordance with the instructions pro vided by Comfort Audio Comfort Audio shall not be liable for performance problems and or damages caused in any way by customer s modification of any part of the equipment Federal Communications Commission Statement This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Programmer DT05 FCC ID UOJ DGO4T Industry Canada This device complies with Industry Canada licence exempt RSS standard s Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including inter ference that may cause undesired operation of the device Le pr sent appareil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de licence L exploitation est autoris e aux deux conditions suivantes 1 l appareil ne doit pas produire de
3. specific frequency Press the pairing button Signal Strength Indicator briefly to remove the marker The white horizental line indicates an average value of RSSI over the whole frequency range Marker Use the graduation bar to the right to determine how strong the interference is If the level of interference is above the green field the Receiver DT10 s ability to receive the signal from the transmitter will be reduced RSSI at the marker To facilitate the reading you can press the pairing button for 3 seconds Then the drawing will freeze Just press the button again to restart the scanning E i requency a the marker RSSI graph Graduation of interference RSSI average value over the whole frequen cy range Lower Upper frequency frequency Programmer D 105 7 8 Battery maintenance Programmer DT05 The rechargeable products in the Digisystem series are equipped with Li Pol batteries le the same type of batteries used for most mobile phones and laptop computers on the market today These types of batteries are able to store large amount of energy in relation to their weight and volume The capacity of Li Pol batteries diminishes during its life cycle The battery type has no memory effect which would mean that you need fully discharge the battery before charging to minimize capacity loss This means that you can just as well charge the battery often and little as opposed to seldom and much S
4. 1 05 Halmstad Sweden Tel 46 0 35 260 16 00 Fax 46 0 35 260 16 50 Canadian Distributor Supportive Hearing Systems Inc 283 MacPherson Avenue Toronto Ontario M4V 144 CANADA Phone 1 800 732 8804 info SimeonCanada com www SimeonCanada com
5. Comfort Digisystem User manual SecureStream I nj Technology Comfort Digisystem Programmer DTOD North America HE Sis qe Comfort Audio HEAR THE FUTURE User manual Table of contents 1 Introduction Comfort Digisystem 2 Regulatory information 3 Functions Programmer DTO5 professional tool 4 Included accessories 5 Programmer DT05 6 Menu Programmer DT05 7 Instructions HA scanner in Programmer DT05 8 Battery maintenance 9 Technical data 10 Radio range and channels 11 Trouble shooting 12 Service and warranty 13 Important safety instructions Page Programmer D105 1 Introduction to the Comfort Digisystem Thank you for choosing Comfort Digisystem Our products are easy to use and give you crystal clear sound Before using the product please read this manual carefully The Comfort Digisystem products feature SecureStream Technology a unique patented digital technology allowing eavesdrop secure radio transfer in real time Comfort Digisystem Programmer DT05 The optional professional tool Programmer D105 can be used to configure the Receiver DT 10 The Programmer D105 also makes it easy to test the Receiver DT 10 with or without a hearing instrument 2 Regulatory information Comfort Digisystem products are not to be used as a substi tute to the hearing aids and should be used in accordance with the specifications and recommendations provided by your physician NOTE Max
6. brouillage et 2 l utilisateur de l appareil doit accepter tout brouillage radio lectrique subi m me si le brouillage est susceptible d en compromettre le fonctionnement Model DT05 IC 6769A DGO4T Programmer D 105 ETL Conforms to UL Standard for Safety for Audio Video and Similar electronic apparatus Safety Requirements UL 60065 Issue 2003 06 30 Ed 7 Rev 2007 12 11 Certified to CSA Standard for Safety for Audio Video and Similar electronic apparatus Safety Requirements CAN CSA C22 2 No 60065 03 Issued 2003 04 01 Ed 1 Amendment 1 2006 Intertek ETL Control number 4002355 WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential instal lation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interfer ence will not occur in a particular installation If this equip ment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on th
7. closer to the talking person Try changing the channel environment Poor range and interference In some environments such as in buildings with a lot of concrete iron or sheer metal structures the range may be reduced There may also be electronic equipment nearby causing interference Change the channel No sound Check that the transmitter and the receiver are set to the same channel Loud hissing noise Check that the Comfort Digisystem units you are using are paired together If Auto sleep is enabled the Receiver DT 10 goes into sleep mode if there is no radio signal But if another radio signal with the same frequency you are using is present the Receiver DT 10 might start again automa tically This could cause a loud hissing noise and that s why Auto sleep should be used with caution Programmer DT03 12 Service and warranty Warranty extension Comfort Audio Inc warrants this product sold to the first end user buyer against defects in materials or workmanship for the time period and as set forth below Pursuant to this Limited Warranty Comfort Audio will at its own option either a repair the product or the parts determined to be defective using new or refurbis hed parts or b provide you with a new or at our option a refurbished unit The repaired or exchanged unit is under warranty for the remainder of the original product s warranty period The warranty does not in clude any other direct indirec
8. e user is encouraged to try to correct the inter ference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help A DANGER DO NOT USE the COMFORT DIGISYSTEM products if you have a PACEMAKER or other implanted device The Comfort Digisystem products could cause the pacemaker or other implanted device to malfunction and cause serious Injury or death 3 Functions Programmer DTO5 optional professional tool Function indicator Volume button Socket for Volume button neckloop On Off Charging socket a Menu control Pairing button Socket for headphones earphones 4 Included accessories Volume indicator e Headphones e Charger A11 Europlug socket Programmer DT03 5 Programmer DTO5 The Programmer DTO5 is an optional professional tool that can be used both for configuring and test listening of the DT10 The Programmer D105 can be used to configure one setting at a time in the Receiver DT10 Select the desired setting in the menu and double press the pairing button The Receiver DT10 must be set to pairing mode The Programmer DT05 can also be used to configure all settings at the same time in a DT10 To do this
9. hese instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not use near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding plug A polarized plug has two blades with one wider than the other A grounding plug has two blades and a third grounding prong The wide blade or the third prong is provided for your Safety If the provided plug does not fit your electri cal outlet consult an electrician for replacement of the incorrect outlet only when using polarized plug Protect the power cord from being walked on or pinched particularly at plugs convenience recepta cles and the point where they exit from the appa ratus Only use attachments accessories specified by Comfort Audio AB Unplug this apparatus during lightning storms or when unused for long periods of time Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as if a liquid has been spilled on the apparatus the apparatus has been Subject to impact by another object or dropped or the apparatus has been exposed to rain or moisture or does not operate normally Start listening at a low volume Too high a volume can seriously damage your hearing Dont dissasemble the product Should the prod
10. pecial charg ing circuits in the Digisystem products protect batteries from overcharging The capacity of the Li Pol batteries deteriorates faster when they subjected to deep discharge Therefore all products of the Digisystem are fitted with a function that automatically turns off the product well before deep discharge occurs Deep discharge may still happen as the battery has a certain self discharge product that is fully or partly charged will with enough time reach a State when the battery deep discharges unless the charger is connected To avoid this we recommend that the battery is charged at least every 6 months Please note Only use the charger supplied by Comfort Audio Changing the battery without the assistance of an authorized dealer will void the Limited Warranty 9 Technical data Programmer DT05 Range 2m Dimensions 2 91 x 1 54 x 0 51 inches 74 x 39 x 13 mm Weight 1 23 oz 35 g FC an Conforms to ANSI UL Std 60065 c e US Certified to CAN CSA Std C22 2 No 60065 03 Intertek 4002355 The weights dimensions capacities performance ratings and other data in Comfort Audio s brochures prospectus circulars advertisements price lists and instructions sheets are mentioned only as general information They are only ap proximate and shall not bind Comfort Audio Programmer DT03 10 Radio range and channels The transmitter and receiver have built in antennas The radio range between the units
11. rammer DI05 and connect head phones or a neck loop to be able to listen 3 Activate pairing mode for the DT 10 by pressing the push button for 2 seconds In the headphones neckloop you receive an acoustic indication e 4 Start the Microphone DM10 and open the menu Select Communication Pairing New code key and answer Yes if you want to create a new code key and transmit It 9 The Receiver DT10 confirms success ful pairing with an acoustic indication 6 Remove the paired DT10 and connect the other DT10 into the Programmer DT05 7 Activate pairing mode on the DT10 by pressing the push button for 2 seconds In the headphones neckloop you receive an acoustic indication e 8 Open the menu on the DM10 and select Communication Pairing Send info 9 The Receiver DT10 confirms success ful pairing with an acoustic indication a Programmer DT03 Always on The setting Always on disables the off function of the push button leaving the Receiver DT10 always on The Receiver DT10 is turned off when turning off the Hearing aid If you enable Always on and at the same time disable Pairing the push button on the Receiver DT10 becomes inoperable Send all To configure a Receiver DT 10 with all settings in the display of the Programmer DT05 select Send all If you choose Send all you will receive the warning All set tings in DT10 will be overwritten Only select Yes if you
12. significantly reduces the power consumption of the Receiver DT10 The Receiver DT10 automatically starts again when you turn on your micro phone Warning If the Receiver DT10 is in sleep mode and another radio signal with the same frequency that you are using is present the Receiver DT10 might start again automatically This could cause a loud hissing noise and that s why Auto sleep should be used with caution Pairing When Pairing is selected the DT10 can be set to pairing mode by pressing the push button for two seconds If Pairing isn t selected pairing mode cannot be enabled with the push button To override this if the Receiver DT10 needs to be reconfigured or if new pairing infor mation needs to be received press and hold the push button on the Receiver DT10 for 2 seconds within 10 seconds of it having been connected to a hearing instrument or a Programmer D105 This sets the Receiver DT10 to Pairing mode and it is then ready to receive new settings from the Programmer DTO5 The Receiver DT10 can receive but not transmit pairing information To pair the Receiver DT10 with your Comfort Digisystem transmitter the Receiver DT10 must be connected either to your hearing instrument or to the Programmer DTO05 Example Make a new eavesdrop secure configuration with one Microphone DM10 and two Receiver DT10s using the Programmer DTO05 1 Put one of the Receiver DT10s into the Programmer DTOS 2 Start the Prog
13. t or consequential damage or loss or any third party damages or losses This Limited Warranty is for a period of two years from the date of purchase as indicated by an original receipt from a Comfort Audio authorized retailer dispenser or medical facility For accessories and batteries the war ranty period is one year as of the date of delivery How to make a warranty claim For warranty service you must contact the Comfort Audio Customer Service listed below to obtain an RMA Return Merchandise Authorization number A description of the defect your name address and telephone number Is required Ship the product freight prepaid via UPS or its equiva lent including a copy of the original purchase receipt any cables earphones and base charger unit in its original packaging or one that offers equal protection Insure your shipment for loss or damage Comfort Audio accepts no liability in case of damage or loss en route to our offices This Limited Warranty does not cover Damage from misuse neglect or normal wear and tear Products that have been modified Products purchased or serviced outside the territory If you purchased your product outside the territory see your retailer for war ranty information 13 Important safety instructions Read these before using your product 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Read these instructions Keep t
14. uct break open because of damage service should only be done by qualified service personnel Never use a transmitter or receiver set to a non permitted frequency Check with the frequency regulatory agency in the country where the equipment is to be used The product contains sensitive electronic equip ment and must be handled carefully Never charge product in closed unaired spaces such as handbags cases or other closed storage bags 20 21 22 23 24 25 26 27 28 Only use batteries and power supply specified by Comfort Audio AB You must not change the battery yourself please contact your point of purchase CAUTION Danger of explosion if battery is incor rectly replaced The product must not be exposed to excessive heat such as sunshine open flames or the like Products include radio transmitters Do not use products where the use of electronic equipment is not permitted such as on airplanes The necklace should not be used if there is a risk of getting stuck e g in a machine or other objects Keep small parts out of reach of children and animals Choking hazard if swallowed Do not leave the product unloaded for too long the battery could get damaged Do not keep the product connected to the charger if it is not used for a longer period Subject to change Programmer DT03 10 Comfort Audio HEAR THE FUTURE Manufactured by Comfort Audio AB Comfort Audio AB Box154 SE 30
15. varies depending on the product and the particular environment you are in Like all radio systems Comfort Digisystem communi cates on specific channels If you use two transmitters on the same channel or a neighbouring one there may be interference Other electronic equipment can also interfere with radio transmissions The channel that you use In your country is perhaps not permitted abroad Always get in touch with your hearing aid provider in your country in order to find out which channels are permitted in different countries Comfort Audio is not liable for unauthorized use of radio waves such as but not limited to interferences with police communication or strategic communication military installations etc 11 Trouble shooting The receiver does not start 1 Check that the correct listening program is selected on the hearing instrument 2 Make sure the Receiver DT10 is correctly connected to the hearing instrument s audio shoe Also check the connection between the audio shoe and the hearing instrument Make sure all connecting surfaces are clean Check replace the hearing instrument s battery 9 Remember to press the push button briefly to switch the DT10 on PS a Poor speech intelligibility The distance between the transmitter and the receiver may be too long The range is around 30 feet 15 meters The distance between the microphone and the talking person may also be too long move the microphone
16. want to overwrite all data in your Receiver DT10 Settings HA scanner The Frequency scanner is used for detecting how much interference there is from a hearing aid within the frequency band that the Receiver DT10 is operating in Language For selection of menu language Factory Reset DTO5 Resets the Programmer DT05 to its default settings DT10 Resets the Receiver DT10 to its default settings which means that also all pairing information is deleted The Receiver DT10 must be set to pairing mode in order to be reset To prevent eaves dropping a new code key must be generated About Software information 7 Instruction HA scanner in Programmer DT05 The HA scanner is used for detecting how much inter ference there is from a hearing aid within the frequency band that the Receiver DT10 is operating in How to use the scanner 1 Enter Setting in the menu of the Programmer DTO05 to activate the scanner 2 Make sure that the hearing aid is on and that the Receiver DT10 is NOT attached d Place the hearing aid close to the Programmer DTO5 see picture to the right and find the position where the interference is worst How to read the scanner The scanner reads and draws the RSSI value on the frequencies between 904 and 927 MHz RSSI Received Reading of specific frequencies If you move the menu control up or down a marker vertical line will appear This is to make a more precise reading of a
Download Pdf Manuals
Related Search