Water Polo Shot Clock F732.qxd
Contents
1. Water Polo Shot Clocks SCs User Guide X N WI p Z Colo MINN Z 2 LN Ma 2 A VII ZAI F732 Rev 0804 S Colorado Time Systems Corporate Office 1551 East 11th Street Loveland CO 80537 USA Sales 800 279 0111 or 1 970 667 1000 Service 800 287 0653 x256 or 1 970 667 1000 x256 Service Fax 970 667 1032 Web www coloradotime com Email customerservice coloradotime com Part Number F732 Rev 0804 02004 Colorado Time Systems All rights reserved Table of Contents 1 Introduction Receiving your Equipment 1 1 2 Setup 8 Operation Installation oooooooooomororronrrono o 2 1 Installing the Portable Stands 2 2 Installing the Speakers 2 2 Attaching the Data Cable 2 3 Operating your Shot Clocks 2 4 3 Maintenance Battery Maintenance 3 1 Internal Battery ON OFF 3 1 Battery Recharging 3 1 Digit Maintenance 3 2 Dear Customer Introduction Thank you for purchasing Colorado Time Systems water polo shot clocks The shot clocks are compact and a very rugged accessory for your water polo program designed to deliver years of trouble free service Please follow the instructions in this booklet to ensure proper installation of your shot clocks and follow the operating instructions t2. d cable into the other jack on the Y connector Insert the other end of the Y connector to the Scoreboard connector on the rear panel of your sports timer as shown in Figure C Note Make sure your sports timer is OFF before attaching the shot clock scoreboard data cable Y CONNETOR TO SPORTS TIMER p CABLE TO l SCOREBOARD SPORTS TIMER SHOT CLOCK 1 Es gn SHOT CLOCKHE bbe __ Figure C Shot clock cabling diagram To attach the other shot clock locate the longer data cable included with your shot clocks Route it through the opening in the back of your first shot clock Plug its connector into the open Data Cable Jack on your first shot clock Next route the cable to the second shot clock Slide the weather shield on the second shot clock back to expose the printed circuit board Route the data cable from the first shot clock through the opening in the back of the second shot clock Plug the cable connector into one of the open Data Cable Jacks on the printed circuit board Refer to Figure C for a cabling diagram Slide the weather shield s back into place and press on the right edge to engage the hook and loop fastener to hold the weather shield in place This completes the cabling connections 2 3 Operating your Shot Clocks Your sports timer program controls the shot clocks No special operator intervention is needed Refer to you
3. imately 12 hours The shot clock circuitry prevents overcharging Digit Maintenance Caution Before attempting any digit maintenance turn off your shot clocks as explained under the Installation section of this user guide The digits on your shot clocks are designed to provide years of trouble free operation However if one or more digit segments do not operate reliably remove the weather shield as explained earlier in this user guide and care fully move the problem segments back and forth by hand several times to confirm that no foreign matter has caused the digit bearings to jam Remove any foreign matter from the digit bearings using compressed air or a clean dry cloth Note Never apply lubricants of any kind to the digit bearings
4. o ensure reliable performance for years to come If you should experience any difficulty installing or using your shot clocks please call Colorado Time Systems Customer Service Department at 970 667 1000 ext 256 Receiving Your Equipment When you receive your Colorado Time Systems equipment follow these steps 1 Open all shipping boxes 2 Check all concealed damage immediately upon receipt of equipment Report any damage directly to the freight carrier 3 Use the list below to take an inventory of all items you received If you believe one or more parts to be missing contact our Customer Service Department immediately Shot clocks 2 e Speakers 2 e Portable stands 2 sets e Data cable set with Y connector Note We recommend that you save all shipping boxes and packing materi al You are responsible for damage to your equipment if an item is returned improperly packed 1 1 Installation 2 Setup amp Operation Caution Before beginning the installation process ensure that your shot clocks are not plugged in to an electrical source Turn off your shot clocks setting the ON OFF switch on the printed circuit board to the OFF position See Figure A for the location of the ON OFF switch Before beginning notice that the weather shield on each shot clock is attached at the right end with a small hook and loop patch Pull the weather shield out slightly before attempting to slide it to the left to expo
5. r Water Polo Software User Guide for complete instructions 3 Maintenance Battery Maintenance Internal Battery ON OFF Battery Recharging For safety reasons the shot clock has been designed to operate on internal battery power only The AC line cord on the shot clock is only for recharging the batteries DO NOT operate the shot clock on AC power in a swimming pool environment The battery power ON OFF switch is located on the printed circuit board of the shot clock See Figure A for the location of the switch When your shot clock is not in use or when you are attaching or removing data cables set this switch to the OFF position If the power switch remains on the battery will discharge even if the shot clock is not being used When you are ready to use your shot clock set the battery power switch to the ON position The shot clock is designed to operate 6 to 8 hours on a single charge Operating time may vary depending on the condition of the battery environmental conditions and operating habits Each time you use your shot clock s recharge the battery fully afterward If the battery is allowed to discharge completely permanent damage to the battery may result To recharge the battery remove the shot clock from the pool area set the battery power switch on the shot clock printed cir cuit board to the OFF position and plug the AC power cord into a stan dard 115VAC wall outlet Allow the battery to charge for approx
6. se the printed circuit board SCOREBOARD FRAME TOP MODULE WEATHERSHIELD HOOK AND LOOP FASTENER PATCH CONTROL ple SPEAKER BOARD E CONNECTORS Figure A Shot clock circuit board components Installing the Po rtable Stands Insert the portable stands into the slots at the bottom of each shot clock as shown in Figure B Figure B Installing portable stands and speaker Installing the Spea ke rs To install the speaker slide the speaker mounting bracket into the slots in the top channel of the shot clock as shown in Figure B above Next slide the weather shield to the left to access the printed circuit board Route the speaker cable through the opening in the back of the shot clock Plug the speaker cable connector into the connector labeled Speaker on the print ed circuit board Repeat the process for the other shot clock Note Do not slide the weather shield back over the shot clocks until you have finished all cabling steps Attaching the Data Cable Locate the data cable set included with your shot clocks Route the shorter of the two cables through the opening in the back of the shot clock Plug the connector on the cable into one of the Data Cable Jacks on the printed circuit board See Figure A for the location of these jacks Route this cable to the Y connector included in this kit Insert the connec tor from the shot clock cable into one of the Y connector jacks Insert your scoreboar
Download Pdf Manuals
Related Search