@HEADER 1B = GETTING STARTED
Contents
1. Use a ribbon when printing on thermal transfer supplies There are two types of supplies Thermal Direct Supplies do not use a ribbon for printing Thermal Transfer Supplies require a ribbon for printing If you are using thermal direct supplies do not load a ribbon See Chapter 3 Loading Supplies for more information The printer automatically detects if a ribbon is installed when you turn on the printer and switches to thermal transfer printing mode Note Make sure the ribbon window and the supply door are closed when you turn on the printer Loading A Ribbon 2 1 To load the ribbon 1 Push down on the ribbon window to unlock it and raise the window 2 The ribbon take up core should already be on the take up reel Attach the take up core to the front hub as shown Ribbon Take up Core Window Take up Reel Back Hub Front Hub 3 Open a package of new ribbon taking care not to wrinkle or crush the ribbon 2 2 Equipment Manual 4 Slide the ribbon onto the ribbon reel as far as it will go Ribbon on Ribbon Reel Ribbon p ed Leader Back Hub Attach the ribbon reel to the back hub Peel and carefully unwind a few inches of ribbon from the bottom of the roll Press the release levers towards the front of the printer to release the supply door oO Nl CO Un Lift open the supply door The supply door support at the right hand rear of the printer holds the supply door open 9 Feed th2. Equipment Manual Monarch 941669 XL 029028 Thermal Transfer Printer A pe DENNISON TC9416TTEM Rev AF 10 09 Each product and program carries a respective written warranty the only warranty on which the customer can rely Avery Dennison Corp reserves the right to make changes in the product the programs and their availability at any time and without notice Although Avery Dennison Corp has made every effort to provide complete and accurate information in this manual Avery Dennison Corp shall not be liable for any omissions or inaccuracies Any update will be incorporated in a later edition of this manual 2004 Avery Dennison Corp All rights reserved No part of this publication may be reproduced transmitted stored in a retrieval system or translated into any language in any form by any means without the prior written permission of Avery Dennison Corp WARNING This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference i
3. 2 Connect a parallel printer cable from the host to the parallel port at the back of the printer 3 Secure the cable with the spring clips For serial communication 1 Turn off the printer before connecting the cable 2 Connect a serial printer cable from the host to the serial port at the back of the printer 3 Secure the cable with the connecting Screws The factory defaults are 9600 Baud no parity 8 bit data frame 1 stop bit and DTR flow control 96 N 8 1 DTR To set communication values refer to the Packet Reference Manual USB Port 9 Pin Serial Port USB Port The printer has a USB Universal Serial Bus Version 1 1 communication port Drivers are available on our Web site for a variety of operating systems Getting Started 1 3 Reading the Indicator Light The indicator light monitors the printer s status Indicator Light GREEN FLASHING GREEN FLASHING RED ORANGE No light 1 4 Equipment Manual Feed Button Indicator Light X Description Printer is on and ready to use Printer is paused Press the FEED button to resume printing Printer error condition See Chapter 5 Troubleshooting for error conditions and solutions The system is detecting the supply and ribbon status Printer is off Make sure the power supply is connected properly See Connecting the Power Su earlier in this chapter LOADING A RIBBON 2 This chapter describes how to load a ribbon
4. eu ed ca ua kd kara a wa wad 4 1 GICAL 0SS UDDIY J3l eu eese anne E e en e e nede Lam ene Eek ke eb 4 1 elle RNN IR cJ 4 2 Gleaning the Platen Roller aNd PIU su nl kya ben Xelk a opa omaia ka ebi tc a bt qan Si epe eru hts 4 2 TROUBLESHOOTING ass arin y 4350y 30551232 a nak eget cee ance ees aderat dun unte d canone h b nto uds 5 1 Printing Problems and SOIMTONS s y 4al yyy et b yb rt S la n n n Ee opo Fre at eie Ee Yo Erde b wl Pueri 0 2 si EINE acr c 9 3 SPECIFICATIONS AND ACCESSORIES nar EROR p REM REED QM upon psu Sube etus e adieu kK KK KAK MEE V A 1 Printer S De CIT CA ll O lS s yi isbat ton D Cete D Al s r k iai dept nekan Vet abor ERA eaten aba Lei A SUPON SPECICIUONS EE TT E _ __ c mr r r ra a aa asagSXSB e mm A 1 RIDDON So TOUT A 2 Prihter ACCESSOS sopenissv tec NERA A oo Drs oder uf d Aa nba cU Er dut Do genda A 2 GETTING STARTED EN The Monarch 9416 XL Thermal Transfer printer is a desktop thermal transfer and thermal direct printer It can print labels tags or receipts with or without bar codes in peel mode one label at a time or non peel mode labels in strips Introduction This chapter includes information about unpacking the printer connecting the power supply E connecting the communication cable reading the indicator light Using This Manual Following is a summary of the contents of th
5. gt Loading Supplies amp Printing 3 1 Loading Supply for Non Peel Mode This section describes how to load supplies in the printer to print in non peel continuous mode Make sure the black mark die cut sensor is set correctly for your supply type See Adjusting the Black Mark Die Cut Sensor for more information Note If you run out of supply while printing do not turn off the printer when reloading the supply You may lose your data The printer resumes printing when reloaded 1 Remove and discard the tape from a new roll of supply Unwrap and discard supply with any glue residue 2 Press the release levers located on both sides of the printer towards the front of the printer to release the supply door 3 Lift open the supply door The supply door support at the right hand rear of the printer holds the supply door open Supply Door Support 3 2 Equipment Manual 4 Remove the supply holder guide from one end of the supply holder The supply holder is normally attached with a line to the inside of the printer not free standing as shown below Do not cut the line Supply Holder Guides 1 5 inch Supply d Adapter C Supply Holder 5 Slide a roll of supply onto the supply holder Note If the core diameter on your roll of supply is 1 inch in diameter remove the 1 5 inch supply core adapters from the supply guide holders 6 Slide the supply holder guide back onto the end of th
6. NC PE at a e DR N N tU DD a DD DD Dr DD a re n a a 1 1 Additi nal DOCUMENTALON HHlxa yn k ple layi yallay aa ctor reddo riti t et ba k a q dod 1 1 UDbackIng tes N L T En p TELA e le ers gest E ne be An KA K ak Li Ke UNI bk G a erwan 1 2 Connecting the Power SUDDIy si kik yey 1a1 4 0ki oov rt ate bika yak eR S EMO Ha dika N ed bti n DAY 1 2 Connecting the Communication Cable ar e t EPI En Eo pto COR Pe oo Ia be otav K k KK 1 3 USB Pol a TE deeds ttai ager r rg gg br br bard cd A f UC ents 1 3 Reading TMe ndear GaN seconde asimindua eiit bab eat uoc talo Huet N re KEYAN EYAN Urat VE aa 1 4 LOADING A RIBBON 2 rto ee eects esu u tazen ya d e KN kane dne ad iss s t D UD M AA SUI D Eu 2 1 Replacing a RIDDOD qetacrivi edet pr tota rb ot nds cer EU tnt poner evene er aaron REUS 2 4 LOADING SUPPLIES amp PRINTING Idus 1o d kk ii e ere er EE 3 1 Loading Supply Tor Non Peel MOQOG eiat eoi ret t rai e Een adu euet kt deret exi ns euo idet 3 2 Loading Labels for Peel Mode acudecetn rni aote pt pO Rabe Su uta do duse bett adus tatu IE Supe MER se kk k kk eps 3 5 Loagthig Falti Fold SUpBlIBS usui pasotutcerg ibat VIN TEM E Rr EE W Veke ler aoi 3 8 Canbrating Ne SUPPI TET 3 9 Adjusting the Black Mark Die Cut Sensor sssssssessseen Hmmm nens 3 10 a jwy eo eooe _ rrr 3 10 CARE AND MAINTENANCE 1 da kak dina kuy ykk ked kaka eoi vespa eoe Wa Wa V n kk W ha y a la k ka l VE
7. Web site for more information The second label shows the model number software version communication settings speed contrast gap sensor setting label length and total number of inches printed 4 To resume normal printing turn off the printer wait two seconds then turn it back on again Troubleshooting 5 3 5 4 Equipment Manual SPECIFICATIONS AND A ACCESSORIES This appendix includes printer supply and ribbon specifications lt also lists the printer s accessories Printer Specifications Height Width Depth Weight Shipping Weight Power Operating Limits Printhead Printing Method 7 4 188 mm 8 4 213 mm 12 4 315 mm 6 3 Ibs 2 9 kg without power supply 12 Ibs 5 4 kg AC Input 100 240 V 50 60Hz DC Output 18 24 V Operation 40 to 105 F 4 to 40 C Storage 40 to 140 F 4 to 60 C Relative Humidity 5 90 non condensing 4 09 104 mm 203 dpi 8 0 dots per mm 300 dpi 11 82 dots per mm Thermal Direct and Thermal Transfer Supply Specifications Supply Types Supply Widths Supply Lengths for peel Labels tags or receipt paper 0 75 19 mm minimum 4 25 108 mm maximum 0 25 6 3 mm minimum 10 0 254 mm maximum 0 75 19 mm minimum 10 0 254 mm maximum Note Hold the leading edge of peeled labels when printing on supply longer than six inches Specifications and Accessories A 1 Ribbon Spe
8. ack mark supplies if necessary move the sensor to the left or right depending on where the black marks are on the supplies The black marks on the supply should cover the square lens inside the sensor Printing Before you print make sure the printer is connected to the host with a communication cable The communication values at the printer must match those at the host The printer s default communication values are 9600 Baud no parity 8 bit data frame 1 stop bit and DTR flow control 96 N 8 1 DTR 1 Turn on the printer 2 Download a format and a batch Refer to the Packet Reference Manual for information on downloading print jobs The printer prints the labels either in peel mode or non peel mode Remove the printed labels 3 10 Equipment Manual CARE AND MAINTENANCE 4 This chapter tells you how to clear supply jams clean the printhead clean the platen roller and printer Clearing Supply Jams When you are printing and a jam occurs the indicator light turns RED To clear the jam 1 Turn off the printer Press the switch on the back of the printer to the OFF position O Note You should turn off the printer s power before you clear a supply jam If you need to clear a supply jam during a print job you may lose your data when you turn off the printer Press the release levers towards the front of the printer to release the supply door Lift open the supply door The supply door support at t
9. cifications Types otandard Core Diameter Inside 1 0 25 4 mm Outside 1 5 38 mm Width 1 6 41 mm minimum 4 3 109 mm maximum Length 300 meters Printer Accessories Use these part numbers when ordering parts Description Centronics Cable IEEE 1284 B to 25 pin male serial Cable 6 DB 9 pin male to DB 9 pin female Parallel Cable 6 DB 25 pin female to DB 9 pin male USB V2 0 Cable male A 2 Equipment Manual Part Number 118363 300017 006 300018 006 125323 028028 Avery Dennison Printer Systems Division 170 Monarch Lane Miamisburg OH 45342 1 800 543 6650 In the U S A 1 800 387 4740 In Canada www monarch com AVERY DENNISON A
10. e end of the ribbon under the printhead and around the take up core 10 Stick the leading edge of the ribbon onto the take up core 11 Rotate the take up core until the ribbon leader is firmly wrapped around the take up core and the black portion of the ribbon is exposed 12 Close the supply door by lifting the supply door slightly and pulling the bottom of the supply door support forward towards the front of the printer Close the supply door slowly and make sure it latches securely Note If you do not latch the supply door completely poor print quality may result 13 Press the ribbon window down firmly until it locks into place Loading A Ribbon 2 3 Replacing a Ribbon To replace a ribbon 1 Push down on the ribbon window to unlock it and raise the window 2 Remove and discard the used ribbon and take up core Save the ribbon reel located inside the take up core before discarding 3 Remove the ribbon reel with core from the back hub and place it on the front hub Ribbon Take up Core Window Take up Reel Back Hub Front Hub 4 Follow the steps from the previous section to finishing loading the ribbon 2 4 Equipment Manual LOADING SUPPLIES amp PRINTING 3 This chapter describes how to load a roll of labels or tags for non peel mode load a roll of labels for peel mode load fan fold supplies calibrate the supply and the ribbon adjust the black mark die cut sensor print 9 gt
11. e supply holder If you are using the supply core adapters for 1 5 inch core supply make sure to push the supply core adapters into the ends of the supply 7 Insert the ends of the supply holder into the slots in the supply roll mount Supply Roll Mount Important Make sure the plastic line attaching the supply holder to the printer is tucked down out of the way of the supply holder and supply holder guides Otherwise the plastic line may wrap around the supply holder or get caught on the supply holder guides Loading Supplies amp Printing 3 3 8 9 10 11 12 Note If you do not latch the supply door 13 14 Slide the supply guides to their widest position Supply Guides Feed the supply printing side up under the white roller under the supply guides and over the platen roller White Roller Platen Roller Press the supply under the supply guides Slide the supply guides so that they barely touch the edges of the backing paper Close the supply door by lifting the supply door slightly and pulling the bottom of the supply door support forward towards the front of the printer Close the supply door slowly and make sure it latches securely completely poor print quality may result Press the FEED button The indicator light should be GREEN Calibrate the supply if necessary See Calibrating the Supply for more information Equipment Manual Loading Labels for Peel Mode Pe
12. e supply roll mount Supply Roll Mount Important Make sure the plastic line attaching the supply holder to the printer is tucked down out of the way of the supply holder and supply holder guides Otherwise the plastic line may wrap around the supply holder or get caught on the supply holder guides 9 Slide the supply guides to their widest position 10 Remove the first two labels from the backing paper 3 6 Equipment Manual 11 Feed the labels printing side up under the white roller under the supply guides and over the platen roller White Roller Platen Roller 12 Press the labels under the supply guides 13 Slide the supply guides so that they barely touch the edges of the backing paper 14 Feed the backing paper under the peel roller and through the peel door opening Peel Rolle 15 Push the peel door closed until it locks If the peel door is not completely closed the supply door does not close properly 16 Close the supply door by lifting the supply door slightly and pulling the bottom of the supply door support forward towards the front of the printer Close the supply door slowly and make sure it latches securely Note f you do not latch the supply door completely poor print quality may result Loading Supplies amp Printing 3 7 17 Press the FEED button A label separates from the backing paper Remove the peeled label and another one prints Note Hold the leading edge of peeled labe
13. el mode separates the label from the backing paper while printing Note The minimum label length for peeling is 0 75 inches 19 mm Hold the leading edge of peeled labels when printing on supply longer than six inches 1 Remove and discard the tape from a new roll of supply Unwrap and discard supply with any glue residue 2 Press the release levers located on both sides of the printer towards the front of the printer to release the supply door 3 Lift open the supply door The supply door support at the right hand rear of the printer holds the supply door open Supply Door Support and the peel bar Peel Bar Peel Roller Peel Door Loading Supplies amp Printing 3 5 5 Remove the supply holder guide from one end of the supply holder The supply holder is normally attached with a line to the inside of the printer not free standing as shown below Do not cut the line Supply Holder Guides 1 5 inch Supply AU Adapter Supply Holder 6 Slide a roll of labels onto the supply holder Note Ifthe core diameter on your roll of labels is 1 inch in diameter remove the 1 5 inch supply core adapters from the supply holder guides 7 Slide the supply holder guide back onto the end of the supply holder If you are using the supply core adapters for 1 5 inch core supply make sure to push the supply core adapters into the ends of the supply 8 Insert the ends of the supply holder into the slots in th
14. he right hand rear of the printer holds the supply door open 4 If necessary remove any previously loaded supply Lift up the supply holder and remove one of the supply holder guides 5 Slide the supply off the holder 6 Remove the jammed supply CAUTION Do Not use sharp or pointed objects to remove supply or damage to the printhead may occur 7 Reload the supply See Chapter 3 Loading Supplies 8 Close the supply door by lifting the supply door slightly and pulling the bottom of the supply door support forward towards the front of the printer Close the supply door slowly and make sure it latches securely Note If you do not latch the supply door completely poor print quality may result 9 Press the FEED button to clear the error The indicator light should be GREEN Care and Maintenance 4 1 Cleaning the Printhead Clean the printhead whenever you notice a decline in print quality or after using three rolls of supply Note You must turn off the printer s power before you clean the printhead If you need to clean the printhead during a print job you may lose your data when you turn off the printer 1 Turn off the printer Press the switch on the back of the printer to the OFF position O 2 Press the release levers towards the front of the printer to release the supply door 3 Lift open the supply door A supply door support at the right hand rear of the printer holds the supply door open Moisten a c
15. is manual Chapter Contents Getting Started Unpacking the printer connecting the cables and reading the indicator light Loading a Ribbon Loading a ribbon 1 2 3 Loading labels tags and receipt paper and printing Printing 4 5 Care amp Maintenance Clearing supply jams and cleaning the printer Troubleshooting Common problems and their solutions A Specifications amp Printer and supply specifications and accessory part numbers Accessories Audience This Equipment Manual is for the person who prints and applies labels Information in this document supersedes information in previous versions Check our Web site for the latest documentation and release information Additional Documentation The printer uses Monarch Printer Control Language ll MPCL II to create labels for printing The Packet Reference Manual available on our Web site describes how to create format and batch packets for printing labels how to configure the printer and perform other advanced techniques Getting Started 1 1 Unpacking the Printer After you unpack the printer you should have 9416 printer power supply power cord ribbon reel take up core already on the take up reel 9 gt Quick Reference CD ROM that contains software and manuals included with applicable models If any items are missing contact Monarch for replacement parts Note Keep all packaging material in case you need to move or return
16. ls when printing on supply longer than six inches 18 Calibrate the supply if necessary See Calibrating the Supply for more information Loading Fan Fold Supplies 1 Place a stack of fan fold supplies behind the printer printing side up Note You may have to move the printer to allow room for the supply 2 Push the external supply guides located on the back of the printer out to their widest position External Supply Guides 3 Adjust the external supply guides so that they barely touch the edges of the supply 4 Feed the fan fold supplies printing side up into the external supply slot on the back of the printer and through the external supply guides 5 Press the release levers located on each side of the printer towards the front of the printer to release the supply door 6 Lift open the supply door The supply door support at the right hand rear of the printer holds the supply door open Leave the supply holder in the printer Slide the internal supply guides to their widest position 3 8 Equipment Manual 9 10 11 12 Note If you do not latch 13 14 Feed the fan fold labels through the supply guides under the supply holder under the white roller and over the platen roller Supply Guides Press the fan fold labels under the supply guides Slide the internal supply guides so that they barely touch the edges of the supply Close the supply door by lifting the supply door
17. n which case the user will be required to correct the interference at his own expense CANADIAN D O C WARNING This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications Le pr sent appareil num rique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num riques de la classe A prescrites dans le R glement sur le brouillage radio lectrique dicte par le minist re des Communications du Canada Trademarks Monarch 94166 and XL are trademarks of Avery Dennison Retail Information Services LLC Avery Dennison is a trademark of Avery Dennison Corp Microsoft and MS DOS are registered trademarks of Microsoft Corporation Windows is a registered trademark of Microsoft in the U S and other countries Centronics is a registered trademark of Centronics Data Computer Corporation Other products are trademarks or registered trademarks of their respective countries and are hereby acknowledged Avery Dennison Printer Systems Division 170 Monarch Lane Miamisburg OH 45342 Lx TABLE OF CONTENTS GETTING STARTED 55y ala UU a ee LUI DD LR DIM LAM ce eee aia 1 1 WTO GUC UO ite DN tdi EA II UM Ulm E deputata UNE CUM reer DUBIE ated r r r 1 1 USIg TNS Manual sesto tau e vnb Lr er REDEEM Ein oa circle Se AN Ka a I22 VPE A Ak ee a DA A v ZAN 1 1 PAU
18. otton swab with isopropyl alcohol Rub the cotton swab across the printhead to remove any build up 6 Allow the printhead to dry for one minute before you close the supply door and resume gt printing PA Cleaning the Platen Roller and Printer Moisten a cotton swab with isopropyl alcohol and run the cotton swab across the platen roller Turn the platen roller with your finger and make sure it is clean all the way around Note Do Not remove the platen roller Platen Roller Slightly dampen a cloth with water and wipe the exterior surfaces clean Use a dry soft bristled brush to clean paper dust out of the interior 4 2 Equipment Manual TROUBLESHOOTING This chapter includes information on possible printing problems and solutions printing test labels Troubleshooting 5 1 Printing Problems and Solutions Problem Indicator light is off when the printer is turned on Indicator light is GREEN but the printer does not print Printing stops and indicator light turns RED Or Printing is not lined up correctly on supply Printing is faded or poor quality 5 2 Equipment Manual Action Check the power connections from the power supply to the printer and the AC outlet See Connecting the Power supply in Chapter 1 for more information Check the cable connections from the host to the printer Connecting the Communication Cable in Chapter 1 for more information Make sure the
19. ribbon and supply are loaded correctly See Chapter 2 Loading A Ribbon and Chapter 3 Loading supplies for more information Clean the printhead See Cleaning the Printhead in Chapter 4 for more information Make sure the supply door is closed completely Calibrate the supply 1 Turn off the printer 2 Load supply for non peel mode See Chapter 3 Loading Supplies for more information 3 Press and hold the FEED button while turning on the printer 4 Release the FEED button after the indicator light starts flashing ORANGE The printer calibrates the black mark or die cut sensor measures the label length prints the test labels and calibrates the ribbon sensor 5 To resume normal printing turn off the printer wait two seconds then turn it back on Problem with the supply Load different supply See Chapter 3 Loading Supplies for more information Make sure the ribbon is not empty Make sure the black mark die cut sensor is set correctly for your supply type See Adjusting the Black Mark Die Sensor for more information Clear a label jam See Clearing Supply Jams in Chapter 4 for more information Make sure the supplies and ribbon are loaded correctly See Chapter 2 Loading Ribbon and Chapter 3 Loading Supplies for more information Clean the printhead See Cleaning the Printhead in Chapter 4 for more information Check the supplies and ribbon for damage or defects Reload
20. slightly and pulling the bottom of the supply door support forward towards the front of the printer Close the supply door slowly and make sure it latches securely the supply door completely poor print quality may result Press the FEED button The indicator light should be GREEN Calibrate the supply if necessary See Calibrating the Supply for more information Calibrating the Supply 1 2 3 Turn off the printer Press and hold the FEED button while turning on the printer To calibrate the supply release the FEED button after the indicator light starts flashing ORANGE The printer calibrates the black mark or die cut sensor measures the label length and prints the test labels To calibrate the ribbon release the FEED button after the printer starts flashing RED The printer calibrates the ribbon sensor To resume normal printing turn off the printer wait two seconds then turn it back on again Loading Supplies amp Printing 3 9 Adjusting the Black Mark Die Cut Sensor The printer has a black mark die cut sensor which it uses to sense and properly calibrate supplies Black mark supply has sense marks black marks on the back of them Die cut supply does not have any black marks For die cut supplies make sure the sensor is in the detented position and the middle of the square lens lines up with the arrow inside the printer Die Cut Black Mark Sensor set for Die Cut Supplies For bl
21. supplies or ribbon if necessary Ribbon and supply are not compatible For thermal direct supplies do not load a ribbon Adjust the print speed darkness contrast Refer to the Packet Reference Manual for more information Problem Action Supply exits partially out of Supply might be caught in the printer See Clearing Supply the printer or skips Jams in Chapter 4 for more information Make sure the supplies and ribbon are loaded correctly See Chapter 2 Loading Ribbon and Chapter 3 Loading supplies for more information For thermal transfer printing make sure thermal transfer requires a ribbon supply is loaded For thermal direct printing make sure thermal direct does not require a ribbon supply is loaded Ribbon is installed but is not See Calibrating the Supply to calibrate the ribbon sensor advancing when printing Printing Test Labels To print the test labels 1 Turn off the printer 2 Press and hold the FEED button while turning on the printer 3 Release the FEED button after the indicator light starts flashing ORANGE The test labels print MONARCH DIOR a umm umm n m n m n mm mm n mm Emu l MONARCH l GAP SENSOR M 0 Am M NM NM NM NM NM NM NM NM IM IL E M IM IM B B MM MM M B HB HB m m m m uw m m m om mg m m m Bow Hg HON The first label shows the printer s configuration by packet A F Refer to the Packet Reference Manual available on our
22. the printer Connecting the Power Supply CAUTION Do Not touch the electrical connectors while setting up the printer Electrostatic discharge can damage or destroy the printhead or electronic components To connect the power supply 1 Place the printer in a location that allows easy access to the front of the printer Note The printer should never be operated while resting on its side or upside down 2 Place the power supply in a suitable location preferably on the floor near an electrical outlet 3 Turn off the printer Press the switch on the back of the printer to the OFF position O 4 Plug the three hole end of the AC adapter cable into the three pronged outlet in the power supply 5 Plug the round end of the power supply cable labeled printer into the socket at the back of the printer 6 Plug the three pronged end of the AC adapter cable into a grounded electrical outlet WARNING The printer and power supply should never be operated in a location where either one can get wet Personal injury could result 1 2 Equipment Manual Connecting the Communication Cable Before the printer can accept print jobs from the host you must connect the communication cable to the printer and the host N set the communication values on the printer to match those at the host only required if you are using the serial port For parallel communication 1 Turn off the printer before connecting the cable
Download Pdf Manuals
Related Search