4602 SIP Telephone Release 1.1 Quick Setup Guide
Contents
1. and enter the proxy server RegistrarServers Delete and enter the registrar servers SiteOption Delete and enter 172 This is the DHCP scope that was created previously on the DHCP server for the SIP telephones For information on how to set up a DHCP server see the section Setting Parameters in the Avaya 4602 SIP Telephone Release 1 1 Administrator s Guide 16 300037 Issue 2 September 2004 DialPlan Delete and enter the dial plan For information on how to configure a dial plan see the section Configuring a Dial Plan in the Avaya 4602 SIP Telephone Release 1 1 Administrator s Guide 16 300037 Issue 2 September 2004 7 When finished save your changes and then exit the file 8 Open the file sip_4602D02A txt and perform the following steps on the specified lines ConfigHttpSrvr Delete and enter the IP address of the HTTP server ProxyServers Delete and enter the proxy server RegistrarServers Delete and enter the registrar servers SiteOption Delete and enter 172 This is the DHCP scope that was Created previously on the DHCP server for the SIP telephones HotLine Delete and enter 0 9 When finished save your changes and then exit the file 7 Convert the 4602 IP phone from H 323 to SIP and then administer the telephone The conversion from H 323 to SIP will take approximately five minutes for eac2. os p Seem i om e fer I rrm arm ae ad ped mis i Bie Poe haar feemmpe ts mo bh Pe mei mer al jeli ir a te f bei 13 Click SIP Settings The SIP Settings page appears llam 1E Stii cima Hoe That hag eA Pabi m onde LP Milks Da DPH ue id pamidatd rgb iana nrn brise Welcome in the mlmisiviration screens for ihe lt SIP 16 300158 Issue 1 1 October 2004 cont 8 14 In the Name box enter the AWOH extension assigned in Avaya Communication Manager 15 In the Password box enter the password for this extension 16 In the Messaging Extension box in the Server Setup area at the bottom of the page enter the extension on Avaya Communication Manager to which this phone will subscribe for Messaging Waiting indication 17 Click the Save button 18 Click Phone Settings The Phone Settings page appears nnmnnn amp pon E 5 i 19 In the Display Name box enter the calling name for this phone that is the name that will appear on the display of the called phone when this phone makes a call 20 Make any other changes 21 When finished click the Save button 22 Click Reset for the changes to take effect for the 4602 SIP phone ai After the phone is converted successfully SIP extension appears on the display of the telephone Repeat Procedure 7 for every 4602 SIP telephone
3. 4602 SIP Telephone Release 1 1 AVAYA Quick Setup Guide This Quick Setup guide is intended for technicians installing Avaya 4602 SIP telephones Before performing the procedures in this guide make sure the following conditions exist e An Avaya Communication Manager CM Release 2 1 1 with field load 415 is installed and running e An Avaya Converged Communications Server CCS Release 2 1 is installed and running e DNS is administered properly if being used by the customer e DHCP scope 172 has been created on the DHCP server Under DHCP Scope Options set Option 172 to ConfigHttpSrvr a b c d where a b c d is the address of the HTTP server e You are familiar with administering Avaya Communication Manager and Avaya Converged Communications Server When setting up SIP trunks you will need to know the following information e number of off PBX stations e maximum number of SIP trunks e node name of the Avaya Converged Communications Server e IP address of the Avaya Converged Communications Server e TAC for the SIP trunk group e number of members for the SIP trunk group Release 1 0 to Release 1 1 Migration Notes In Release 1 0 of the 4602 SIP Telephone the extension name of the 4602 SIP telephone had to be different from the extension name used in Avaya Communication Manager In Release 1 1 which is supported by Avaya Communication Manager Release 2 1 1 and Avaya Converged Communications Server Rele
4. ase 2 1 the extension name of the 4602 SIP telephone must be identical to the extension name used in Avaya Communication Manager e Changes on Avaya Communication Manager Only OPS administered SIP endpoints are supported in Avaya Communication Manager Release 2 1 1 Pure SIP or standalone configurations are not supported Hotline is not supported Assign an AWOH station number for the SIP OPS endpoints if not done already Only AWOH is supported in Avaya Communications Manager Release 2 1 1 Update the off pbx telephone station mapping so that the station names of the AWOH and the 4602 SIP telephone match e Changes on Avaya Converged Communications Server Update existing Avaya Converged Communications Server user records to include a Media Server Extension The Media Server Extension should match the AWOH station assigned in Avaya Communication Manager lf the user handle is an extension it must match the AWOH station assigned e Changes on the 4602 SIP Telephone Change the extension name so that it matches the AWOH station name on Avaya Communication Manager Remove the Hotline option and Extension in the Call Handling page Enter the registration domain name in the configuration files so that the 4602 SIP Telephone can register with Avaya Converged Communications Server Release 2 1 16 300158 Issue 1 1 October 2004 2 Configure the Avaya Communication Manager 1 Use
5. de Name Enter the node name of the Avaya Converged Communications Server you entered in Step 2 of Procedure 1 Near end Listen Port to 5061 This is the default setting Far end Listen Port to 5061 Far end Domain Name Enter either the local Avaya Converged Communications Server domain name or the far end SIP server domain name to be reached DTMF over IP to rtp payload This is the default setting Use the add trunk group command to add a SIP trunk group Set the following parameters Group Type to sip Group Name TAC You must enter a TAC even though the TAC is not used for accessing a SIP trunk Service Type to tie Signaling Group to the number of the signaling group you created in Step 1 of this procedure Number of Members up to 255 This is the number of concurrent users who will be using the trunk Administer fields on page 2 as appropriate for the customer 3 Use the change route pattern command to route outgoing calls over the SIP trunks by using AAR ARS Set the following parameters Trunk Group Number to the number of the trunk group you added in Step 2 FRL to 0 or appropriate FRL number A route pattern name that is easy to identify Note Even though AAR ARS and therefore route patterns is optional in Avaya Communication Manager R2 1 1 you need a route pattern administered for next step 4 Use the change locations comma
6. f Procedure 2 It is recommended that you use the trunk number Configuration Set Enter 1 if you want to use the default settings Be sure to review the fields under the configuration set to customize for each customer For customers that do not use the North American dial plan Fast Connect on Origination should be set to Yes to receive Avaya Communication Manager call progress tones If extended features will be used use the change off pbx telephone feature name extensions command to assign extensions to available features such as conferencing call forwarding and send all calls 16 300158 Issue 1 1 October 2004 3 Configure the Avaya Converged Communications Server 1 Create a Media Server The Media Server provides a connection between the Avaya Converged Communications Server and the Avaya Communication Manager using a designated CLAN procr Create Address Maps for the Media Server you created in Step 1 These address maps will be used to represent Avaya Communication Manager dial plans For example the map sip 123 0 9 2 avaya com will map extensions 12300 to 12399 inclusive to the media server contact The map sip 91732 0 9 7 avaya com will allow users to dial a telephone number in the 732 area code Address maps will be needed for all call types 911 local extension dialing local outside long distance international 3 Add a user for the 4602 SIP phone Set the foll
7. h telephone 1 Connect the 4602 IP phone to the system 2 At the 4602 IP phone press when Press to program appears on the display of the telephone 3 Press to go through all of the settings and access a blank screen Do not change any of these settings 4 At the blank screen press MUTE 7 4 4 Sig default appears on the display of the telephone 5 Press until Sig SIP appears on the displays of the telephone 6 Save the changes 7 Press MUTE 7 3 73 8 to reset the telephone Do not reset the values The telephone will convert from H 323 to SIP After approximately five minutes the following message will appear on the display of the telephone No Service 8 Press MUTE 4 6 3 6 The IP address of the telephone is displayed You may want to write down this IP address 9 Start your web browser enter the IP address of the 4602 SIP phone from Step 2 and press ENTER The Login dialog box appears Eper Secleech Feri seri Fs kii i Pibies hpr paa iar ame el ee ii Le 1 Fiss Telm a liis Pisna E Parai T aishi paced in pon adel bl 16 300158 Issue 1 1 October 2004 5 7 10 In the User Name box type admin 11 In the Password box type barney cont 12 Click the OK button The 4602 home page appears Telephone Cheese q iik a orbed am arijriiy Bhi 1a 5 a Eamak A O oi ii te OF arraing of Quake of Dr Tere ia T Jimo ee larm h k et la ee ie phoma e b amr Soom
8. nd to specify the route pattern Set the following parameters Proxy Sel Rte Pat to the route pattern you added in Step 3 Make the same route pattern entry for each location administered on this form 5 If using AAR use the change aar analysis command to specify how Avaya Communication Manager will analyze a digit string to determine the pattern for the call Set the following parameters Minimum maximum digits to be used in the trunk call Route pattern Use the add station command to create an AWOH station for the 4602 SIP phone on the Avaya Communication Manager Only AWOH stations are supported in the Avaya Communication Manager Release 2 1 offer Use the default settings for all fields except the Port field Enter X in the Port field Configure an OPTIM extension on the Avaya Communication Manager 1 Use the add off pbx telephone station mapping command to configure an OPTIM extension Set the following parameters Station Extension to the extension of the 4602 SIP phone You added this extension in Procedure 3 Application to OPS Dial Prefix to the AAR ARS code used for the SIP trunk if AAR ARS is being used Otherwise this field is blank Phone Number to the extension administered on the Avaya Converged Communications Server Set Trunk Selection to either aar ars or the trunk number of the SIP trunk This is the trunk group number you specified in Step 2 o
9. owing parameters User Handle Enter a name or number While you can enter a number it is recommended that you enter a name The media server extension will resolve which devices will ring for the selected user Password The password is alphanumeric Host to which the user will register First Name of user Last Name of user Add Media Server Extension The Media Server Extension should match the AWOH extension created on Avaya Communication Manager 16 300158 Issue 1 1 October 2004 Modify and copy the configuration files to the appropriate servers You can download the files in this step from www avaya com support 1 Save your changes and then copy the file 46xxupgrade scr to the TFTP server Copy the file 323tosipOxxx bin to the TFTP server This file instructs the 4602 telephone to change from H 323 to SIP Copy the file sip_4602bt0xxx ebin to the root directory of the HTTP server Copy the file sip_4602ap0xxx ebin to the root directory of the HTTP server Copy the following files to the root directory of the HTTP server sip _4602D01A txt This file will be used by 4602 telephones sip _4602D02A txt This file will be used by 4602SW telephones Open the file sip _4602D01A txt and perform the following steps on the specified lines ConfigHttpSrvr Delete and enter the IP address of the HTTP server ProxyServers Delete
10. the change system parameters customer options command to set the following parameters the maximum number of off PBX telephones OPS page 1 of form the maximum number of SIP trunks page 2 of form Enhanced EC500 to y page 4 of form IP trunks to y page 4 of form A Important These parameters are determined by the license file Only an Avaya authorized representative can modify these parameters Use the change node names ip command to set the following parameters host name of the Avaya Converged Communications Server IP address of the Avaya Converged Communications Server Use the change system parameters features command to set Trunk to Trunk transfer to all Use the change ip network region command to set the home domain domain com of the Avaya Converged Communications Server on all applicable regions 16 300158 Issue 1 1 October 2004 Set up a SIP trunk between the Avaya Communication Manager and the Avaya Converged Communications Server 1 Use the add signaling group command to add a SIP signaling group Set the following parameters Group Type to sip Transport Method to tls This is the default setting Depending on the type of system perform one of the following steps e Foran S8500 system or an S8700 system set Near end Node Name to a designated CLAN e For an S8300 system set Near end Node Name to procr Far end No
Download Pdf Manuals
Related Search