Model MTI-5 Operator`s Manual
Contents
1. AUTOFRY The Leader in Ventless Deep Frying Technology Model MTI 5 Operator s Manual A Patented Product of Motion Technology Inc 6 Huron Drive Natick MA 01760 Telephone 508 653 0082 Technical Support 888 664 6640 MTI Form OP 0005 Rev 002 7 98 E167653 AUTOFRY Models MTI 5 Rev 2 Operator s Manual AUTOFRY Model MTI 5 Specifications Electrical Specifications Consult wiring diagram at the end of this document for specific ratings 240V ac single phase grounded 50 60HZ 4200 Watt 16 67AMPS NEMA 6 20 Plug Configuration INTERNATIONAL ONLY NO PLUG ATTACHMENT 230V ac single phase grounded 50 60Hz 2950 Watt 13 00 AMPS US Replace cord set with Motion Technology Inc cord set ONLY part number 52097 Physical Specifications Materials 304 Stainless Steel Dimensions 21 x21 x21 Clearances Left side 2 Min Right side 12 for heat lamp Rear 3 Min Top 24 Min Oil capacity 2 5 US Gallons Approvals and Listings UL cUL NSF CE CSA AUTOFRY and NO HOODS NO VENTS NO PROBLEM are registered trademarks of Motion Technology Inc MTI Form OP 0005 Rev 002 7 98 E16 654 AUTOFRY Models MTI 5 Rev 2 Operator s Manual Table of Contents Prepare electrical service Prepare counter top Set up and Installation Remove components Re set high limit Leg installation Initial cleaning Install charcoal filter Install oil pot Install heater box Install food basket clip Install food baske2. E167654 17 AUTOFRY Models MTI 5 Rev 2 Operator s Manual Programming Cook Times cont Key 3 1 Press the 2 button e The display will read 003 2 Press the 1 button to view or edit the pre set cook time e The display will read 3 00 3 Press the 2 key to increase the cook time or press the 3 key to decrease the cook time 4 Press the 1 button to save the changes The display will read 003 If you do not wish to continue re programming the other 3 buttons simply press the OFF button Otherwise with the display reading 003 follow these instructions Key 4 Press the 2 button The display will read 004 Press the 1 button to view or edit the pre set cook time The display will read 4 00 Press the 2 key to increase the cook time or press the 3 key to decrease the cook time 4 Press the 1 button to save the changes e The display will read 004 wo N If you do not wish to continue re programming the other 2 buttons simply press the OFF button Otherwise with the display reading 004 follow these instructions Key 5 Press the 2 button The display will read 005 Press the 1 button to view or edit the pre set cook time The display will read 5 00 Press the 2 key to increase the cook time or press the 3 key to decrease the cook time 4 Press the 1 button to save the changes e The display will read 005 oe N lf you do not wish to continue re programming the last button simp
3. resistant Stainless steel fire resistant plastic laminate or solid surface materials are acceptable Never use a porous material to prepare food as bacterial contamination could result MTI Form OP 0005 Rev 002 7 98 E167654 AUTOFRY Models MTI 5 Rev 2 Operator s Manual AUTOFRY Installation CAUTION You will need assistance to position and install the AUTOFRY The approximate weight of the unit is 130 pounds 1 Remove and save the packing materials Be sure to inspect the AUTOFRY Your AUTOFRY has left the factory in perfect condition and has been packaged to withstand rugged travel However in the event that you observe damage to the AUTOFRY you should contact the carrier immediately and report any damages Be sure that you have your signed bill of lading 2 Take out the removable components from inside the AUTOFRY e 4 adjustable legs e Food exit chute e Wire food basket e Heater box assembly e Oil pot Check the red high limit re set button on the bottom of the heater box assembly by fully depressing it with the eraser end of a pencil If the limit has been tripped you will hear a click See Figure 1 Use the end ofa pencil to re set limit MTI Form OP 0005 Rev 002 7 98 E167654 AUTOFRY Models MTI 5 Rev 2 Operator s Manual 3 e Charcoal filter removal and leg installation e With the AUTOFRY still on its shipping pallet tilt the unit backward and remove the charcoal filter from the foo
4. 12 seconds then shut off The display will read Sft Individually remove each of the components listed below Close the main door and press the ON button The fan will operate for approximately 10 12 seconds then shut off The display will read Sft The filter cover plate The grease baffle The second filter The charcoal filter The removable fire damper stack cover MTI Form OP 0005 Rev 002 7 98 E167654 25 AUTOFRY Models MTI 5 Rev 2 Operator s Manual Safety System Test cont The AUTOFRY is equipped with an air flow switch To test this switch follow these instructions 1 With all the filter components installed and the main door closed press the ON button at the keypad 2 Using a flat piece of cardboard or 1 4 plywood completely block the exhaust flow at the fire damper stack cover e The fan will begin to operate It can take upwards of 45 minutes for the air flow switch to react to the blockage However after the air switch has closed the display will read Sft lf the oil has heated above 151 F the fan will continue to operate until it cools to 120 F Included with this manual is a maintenance log that must be signed and dated after the completion of the daily weekly and quarterly maintenance and testing Your local or State health and safety inspectors may require this log to be posted in a conspicuous location MTI Form OP 0005 Rev 002 7 98 E167654 26
5. cook for 2 minutes and 30 seconds Push 2 3 and 0 The display will read 2 30 If you enter the wrong time press CLEAR and re enter your cook time Most food products will have recommended cook times printed on their packaging use these cook times as a base line starting point 2 Open the food entry door and place the food product to prepare in the food chute Never over fill the food entry chute 3 Close the food chute and push the START button A CAUTION Never overload the food entry chute Over loading will result in splashing The AUTOFRY can cook a maximum load of 1 1 2 Pounds 68 kg of french fries Never place ice into the AUTOFRY Ice will cause boil over Never entry an order until the GREEN READY light is on MTI Form OP 0005 Rev 002 7 98 E167654 13 AUTOFRY Models MTI 5 Rev 2 Operator s Manual During Cooking The O READY light has gone out and the O WAIT light will illuminate The display will count down the selected cook time The wire food basket now contains your food product It will automatically be lowered into the oil pot At the end of the COOK CYCLE oil temperature replaces time at the display The wire food basket will be raised out of the oil pot and drain the food product for 12 seconds e At the conclusion of the DRAIN CYCLE the basket will dispense the food down the food exit chute You may hear the sound of the basket hitting the sidewall This is a normal condition e The DISPENSE CYC
6. room temperature of at least 75 F following the manufacturer s label instructions Polish the exterior surfaces using a commercial grade stainless steel polish and a soft cloth Replace all the clean dry components and add oil or shortening as needed MTI Form OP 0005 Rev 002 7 98 E167654 21 AUTOFRY Models MTI 5 Rev 2 Operator s Manual Weekly Cleaning s Repeat daily cleaning ce Remove the heater box assembly CAUTION Never immerse the heater box Permanent damage and or electric shock will result Use caution when cleaning around the temperature probes ae Remove the oil pot e Discard the oil or shortening in an environmentally safe manner e Clean all surfaces to bare metal e Re apply a thin even coating of Kote brand soil shield to the exterior surfaces of the oil pot Clean all interior surfaces to bare metal A CAUTION Use extreme caution when cleaning around the fire system actuation cables and fusable link in the interior cabinet Accidental discharge of the fire system could result See figures 1 sanitize all part and interior surfaces in a quaternary ammonia or iodine 5 solution at a room temperature of at least 75 F following the manufacturer s label instructions MTI Form OP 0005 Rev 002 7 98 E167654 22 AUTOFRY Models MTI 5 Rev 2 Operator s Manual uarterly Cleaning and Maintenance CAUTION Disconnect un plug the AUTOFRY from main power A o Perform weekl
7. LE is repeated once to ensure that all the food has been emptied from the wire food basket The wire food basket will return to the ready position the O WAIT light will go out and the O READY light will illuminate A quick beeping sound will occur to signal that the AUTOFRY is ready for the next order AUTOFRY Shutoff Procedure Push OFF e The keypad display will shut off immediately and the oil will begin to cool The AUTOFRY is safely shut off cleaning the fan will continue to run for about 2 hours or until the oil The oil will remain hot for a long period To assure continuous air WS temperature falls below 190 F MTI Form OP 0005 Rev 002 7 98 14 E16 654 AUTOFRY Models MTI 5 Rev 2 Operator s Manual Additional KEYPAD Functions The Count Button The COUNT button tracks equipment cycles and this function can be utilized to record sales and control inventory To use COUNT follow this procedure The AUTOFRY has two count features A re settable count and a total cumulative count To access these count features simply press the COUNT button once to view the re settable count While the count is on the display press the CLEAR button to clear the count By pressing the COUNT button twice you can view the total non resettable count e From 0 999 total COOK CYCLES the keypad will display ONE set of THREE numbers examples 1 030 30 total cook cycles 2 302 302 total cook cycles 3 999 999 total cook cy
8. Rev 2 Operator s Manual Programming Cook Times The AUTOFRY offers you the ability to program the 1 6 keys for your most common cook times lt is a good idea to write down your six most commonly used cook times prior to programming the AUTOFRY Instructions for programming are as follows Entering the programming mode 1 Press the OFF Button 2 Simultaneously press the 2 and 0 buttons e The display will read P 3 Press 2 then 2 then 2 then START e The display will read 001 Key 1 1 Press the 1 key to view or edit the pre set cook time e The display will read 1 00 2 Press the 2 key to increase the cook time or press the 3 key to decrease the cook time 3 Press the 1 key to save the changes e The display will return to 001 If you do not wish to continue re programming the other 5 buttons simply press the OFF button Otherwise with the display reading 001 follow these instructions Key 2 Press the 2 button The display will read 002 Press the 1 button to view or edit the pre set cook time The display will read 2 00 Press the 2 key to increase the cook time or press the 3 key to decrease the cook time Press the 1 button to save the changes e The display will return to 002 wo N If you do not wish to continue re programming the other 4 buttons simply press the OFF button Otherwise with the display reading 002 follow these instructions Next Page MTI Form OP 0005 Rev 002 7 98
9. cles e At 1 000 total cook cycles and up to 6 999 the keypad will display TWO sets of THREE numbers examples 1 001 followed by 002 1 002 total cook cycles 2 006 followed by 001 6 001 Total cook cycles e After 6 999 total cook cycles the counter will return to 000 MTI Form OP 0005 Rev 002 7 98 E16 654 15 AUTOFRY Models MTI 5 Rev 2 Operator s Manual The Stand By Button The Button is used during off peak hours to conserve energy and maximize oil life To Activate Stand By Mode For all AUTOFRY models press the button and the O STAND BY light will illuminate The heating element shuts off until the oil temperature drops below 300 F and then maintains this temperature To Exit Stand Bv Mode Press the CLEAR button The O STAND BY light will go out and the oil will begin to heat up until it reaches the ready temperature Never shut off the AUTOFRY while in the Stand By mode as the keypad may remain locked in the Stand By mode If this should happen when you re start the AUTOFRY simply press the CLEAR button Repeat Cook Time Use the following procedure to repeat the last entered cook time e Simply press the START and your last cook time will be repeated This may be useful if you have a single product menu or multi product menu with identical cook times Maximum Cook Time The AUTOFRY has maximum cook time of 15 minute and 59 seconds MTI Form OP 0005 Rev 002 7 98 E16 7654 16 AUTOFRY Models MTI 5
10. d exit cutout e Install two of the adjustable legs by rotating them clockwise to a hand tight fit into the front two leg plates located on the underside of the AUTOFRY e Tilt the AUTOFRY forward and repeat the leg installation for the rear two legs see Figure 2 Install the legs by rotating clockwise into Figure 2 Install legs 4 Place on counter e Carefully place the AUTOFRY on the counter e Adjust the legs as needed to level the AUTOFRY e Make sure that nothing is placed on top of the AUTOFRY Which could obstruct the exhaust system MTI Form OP 0005 Rev 002 7 98 E 167654 AUTOFRY Models MTI 5 Rev 2 Operator s Manual D Initial Cleaning e Wash the oil pot wire food basket and food exit chute in warm soapy water followed with a clear water rinse e Remove the food exit chute by turning the food chute knob counterclockwise see Figure 3A e Separate the two piece food entry chute and wash in warm soapy water followed with a clear water rinse see Figure 3B Food entry chute knob Figure 3A Remove food entry Figure 3B Separate food entry chute 6 e Sanitize parts e All parts must be sanitized in a quaternary ammonia or iodine solution at a temperature of at least 75 F following the manufacturers label instructions e Re assemble and re install the clean dry parts Next Page MTI Form OP 0005 Rev 002 7 98 E167654 AUTOFRY Models MTI 5 Rev 2 Operator s Manua
11. il changing as an important part of your regular maintenance will enhance the taste of your food product and reduce the risk of smoke Oil changing will vary widely depending on the use of the AUTOFRY However the use of a shortening monitor kit is the most accurate means of determining the status of the oil AS CAUTION DO NOT use jets to clean the AUTOFRY There is risk of electric shock NEVER immerse the heater box assembly Daily Cleaning Remove and wash the following in warm soapy water followed by a a a clear water rinse The wire food basket The food entry chute The food exit chute The filter cover plate The grease baffle The second filter Zu Thoroughly dry all parts ace Remove the charcoal filter and wipe down the exterior surfaces with a clean damp cloth or paper towels AN CAUTION Never soak the charcoal filter as permanent damage to the charcoal medium will result MTI Form OP 0005 Rev 002 7 98 E167654 20 AUTOFRY Models MTI 5 Rev 2 Operator s Manual Daily Cleaning cont Fusable link and cable Figure 17 MTI 5 Fusable link and actuation cable Use extreme caution when cleaning around the fire system actuation cables and fusible link in the interior cabinet Accidental discharge of the fire system could result see Figure 12 Bn Do 6 Uc Clean all interior surfaces to bare metal sanitize all part and interior surfaces in a quaternary ammonia or iodine solution at a
12. ilter The second filter must be replaced a minimum of once every 6 months Heavy usage may require that the second filter be changed more frequently however if it appears the second filter can no longer be cleaned effectively then it should be replaced Second filters can be ordered by calling 1 800 348 2976 MTI Form OP 0005 Rev 002 7 98 E16 654 24 AUTOFRY Models MTI 5 Rev 2 Operator s Manual Semi Annual Cleaning and Maintenance Fire Suppression System AZDIIOVs lt PSamsaxm An inspection report insurance certificate of installation will be forwarded to you by mail shortly after shipment of your AUTOFRY This document must be filed in a safe place for future reference An inspection of the fire suppression system must be performed every six months in order to comply with NFPA 96 NFPA 17A and UL 197 A certified fire equipment maintenance company must perform this inspection Consult your fire suppression system manual that has been supplied with this document for details on the inspection and re charge instructions Safety System Test The safety system must be tested a minimum of once every six months A qualified equipment repair technician following these instructions should perform this inspection This test must be started with a full oil pot of clean cool liquid shortening ail Open the main door of the AUTOFRY and press the ON button O 2 Sa a oR QN The fan will operate for approximately 10
13. l 1 Install Charcoal F ilter e Remove the filter cover plate from the back interior wall of the cooking chamber by removing the two black plastic knobs securing the cover plate see Figure 4 Remove the charcoal filter from the plastic bag with the flange facing down and facing you insert it into the tracks above the second filter see Figure 5 e Re install the filter cover plate by turning the black plastic knobs clockwise to a hand tight fit Verify that the word TOP on the filter cover plate is in the upper left hand corner see Figure 4 lf the filters or the filter cover plate are not installed or installed incorrectly the AUTOFRY will display Sft at start up i y yi Black plastic knobs p 4 e orn toes AA i n a a z Fr Figure 4 Filter cover plate Figure 5 Charcoal Filter Both the grease baffle and the second filter have small holes along the one side of the frame These drain holes must be facing down in order for the filters to efficiently drain and clean the air See Figure 5 653 S anitize interior All interior surfaces must be sanitized in a quaternary ammonia or iodine solution at a temperature of at least 75 F following the manufacturer s label instructions MTI Form OP 0005 Rev 002 7 98 E167654 AUTOFRY Models MTI 5 Rev 2 Operator s Manual oR Install oil pot e Place the oil pot into the cooking chamber Ensure that the taller of the two oil po
14. lose and lock the main door of the AUTOFRY e Attach the power cord into its socket at the rear of the AUTOFRY e Plug the AUTOFRY into the properly rated single phase grounded outlet e Move the power switch located at the right side of the AUTOFRY tothe ON possition e Press the ON button at the keypad The display will show current oil temperature see start up notes bellow e The AUTOFRY will take between 15 20 minutes to reach the ready temperature It is important to allow the AUTOFRY to reach the ready temoerature prior entering food o _ lt _ START UP NOTES amp _ _ If the display reads Sft check the following 1 All three filters are installed firmly into their filter tracks 2 The filter cover plate is installed and the two black knobs are seated firmly 3 That the front door is closed tightly and locked 4 There is nothing blocking the air exhaust vent at the top of the AUTOFRY 5 That the fire system pressure gauge is in the Green charged area If the display reads Prb check the following 1 That the heater box assembly is installed 2 That the heater box assembly is firmly seated onto its sockets If the display reads A07 or _ A08 check the following 1 That the heater box is firmly installed onto its sockets 2 That there is oil in the oil pot to 1 2 3 4 bellow the fill line Press the OFF button to clear the display of any error message e You are now ready to
15. ly press the OFF button Otherwise with the display reading 005 follow these instructions MTI Form OP 0005 Rev 002 7 98 E16 654 18 AUTOFRY Models MTI 5 Rev 2 Operator s Manual Programming Cook Times cont Key 6 1 Press the 2 button e The display will read 006 2 Press the 1 button to view or edit the pre set cook time e The display will read 6 00 3 Press the 2 key to increase the cook time or press the 3 key to decrease the cook time 4 Press the 1 button to save the changes e The display will read 006 Exit programming mode To exit the programming mode press the OFF key You have now pre programmed your AUTOFRY for optimum convenience Using the pre programmed times To use the pre programmed keys simply press the 1 6 key The display will show 001 006 Place the selected food into the food entry chute close the entry chute door and press the START key The display will count down the pre programmed time MTI Form OP 0005 Rev 002 7 98 E16 654 19 AUTOFRY Models MTI 5 Rev 2 Operator s Manual Recommended Cleaning Schedule In order to ensure compliance with State local and VERY IMPORTANT National health and safety standards regular maintenance must be performed Regular maintenance is extremely important for the health and safety of your customers Proper maintenance is very important in order for your AUTOFRY to continue to operate without the need for a hood and duct system Regular o
16. s MTI 5 Rev 2 Operator s Manual afl B Add liguid shortening 2 5 2 75 Gallons e Add liquid shortening to the oil pot Ensure that the oil level is approximately 1 2 3 4 below the upper fill line stamped on the interior of the oil pot Oil level should be maintained between the upper and lower fill levels at all times It is simpler and safer to add cool shortening to the oil pot than it is to remove hot shortening Once the AUTOFRY has heated the shortening will expand Only after this expansion has finished should the oil level be increased to the upper FILL level Over filling will result in excessive splashing never over fill the oil pot Under filling the oil pot will result in under cooked food product or poor and erratic temperature readings Extreme low oil levels will cause smoking NEVER operate the AUTOFRYin a low or no oil condition there is risk of fire due to extreme low oil levels af Al Install the food exit chute e Secure the food exit chute flange side up into the cut out on the right hand side of the i AUTOFRY inserting the food exit chute into the cut out space and lifting up into the cavity until the flange can be placed over the OP ee 4 raised edge of the Exit chute and internal wall see internal wall Figure 9 feces Figure 10 Install exit chute MTI Form OP 0005 Rev 002 7 98 E16 654 10 AUTOFRY Models MTI 5 Rev 2 Operator s Manual al Da Power e C
17. start cooking Please turn to Let s Get Cooking MTI Form OP 0005 Rev 002 7 98 E167654 11 AUTOFRY Models MTI 5 Rev 2 Operator s Manual Let s Get Cooking Starting the AUTOFRY e With the main door closed and locked press the ON button to begin heating the oil e The O WAIT light will illuminate on the keypad and the exhaust fan will Start to run e The current oil temperature will appear on the keypad e When the oil temperature reading is between 190 F 220 the wire food basket will complete one test cycle At this time you will hear the basket hitting the sidewall of the AUTOFRY This is a normal condition press the OFF button at the keypad Open the main door to check the oil level Add oil if necessary to fill the oil pot to the upper FILL line Close the main door and press the ON button to re start the AUTOFRY WS When the oil temperature at the display reaches 300 F q The AUTOFRY will be ready at 340 F It takes the AUTOFRY between 12 20 minutes to heat the oil to 350 F Although the heating element is programmed to stop heating at 350 354 F the oil temperature can go as high as 365 F due to the circulation of the oil in the oil pot This is a normal condition MTI Form OP 0005 Rev 002 7 98 12 E16 654 AUTOFRY Models MTI 5 Rev 2 Operator s Manual Begin Cooking Cooking with the AUTOFRY is as simple as 1 P 2 P 3 p 1 Enter a cook time by pushing buttons 0 9 on the keypad For example to
18. t Add liquid shortening Install food exit chute Power Let s get cooking Starting the AUTOFRY Begin cooking During cooking Shut off procedure Additional keypad functions Count button Stand by button Programming cook times Recommended Cleaning Schedule Daily cleaning Weekly cleaning Quarterly cleaning Charcoal filter Semi annual Fire system Safety system test MTI Form OP 0005 Rev 002 7 98 E167654 COW OAANHN NAH HW HF W Y NO NO NO NNN N e KK BF e e e e e eS NN rAtpPhPwWNRK VT wWaunnst BwWNN KF CO CO AUTOFRY Models MTI 5 Rev 2 Operator s Manual AUTOFRY MTI 5 Rev 2 Set up and Installation The AUTOFRY comes from the factory complete with everything you will need to start cooking with the exception of food and oil By following these simple instructions you can have your AUTOFRY installed and ready to earn profits for you in as little as 30 minutes Prepare electrical service A licensed electrician in accordance with the National Electrical Code NEC and all local codes must install electrical service Do not alter the factory supplied power cord or plug Never attach the AUTOFRY to an extension cord Consult the Identification Tag for equipment wattage and voltage Motion Technology Inc will not assume responsibility for any injuries or equipment malfunctions resulting from non conforming electrical installations Prepare counter top Choose a counter top location that is sturdy level easily cleanable and fire
19. t handles is towards the rear of the cook chamber and that both handles are fully lowered see Figure 6 Taller handle towards back Both handles lowered Experience has shown that a light application of Kote brand soil shield or Pam on the exterior surfaces of the oil pot will prove helpful when it is time to clean the oil pot al 0 a Install the heater box assembly Install the heater box assembly onto the heater box deck located to the left of the oil pot Ensure that the heater box assembly seats firmly onto the sockets see Figure 7 4 _ a 3 fe a Lower elements into oil pot Seat heater box onto jiu eee sockets Figure 7 Install Heater Box MTI Form OP 0005 Rev 002 7 98 E167654 8 AUTOFRY Models MTI 5 Rev 2 Operator s Manual afl afl o Install the food basket clip e Install the food basket clip onto the two mounting buttons located to the right of the door opening by aligning the holes in the clip over the buttons see Figure 8 pi zt a ig F J Lower clip down to lock in place Align clip over buttons Figure 8 Install basket clip afl De Install the food basket e Install the square end of the basket rod into the cam located on the rear wall of the AUTOFRY see Figure 9A e Lower the round end of the basket rod into the basket clip see Figure 9B Figure 9B round end of cam rod in clip MTI Form OP 0005 Rev 002 7 98 9 E167654 AUTOFRY Model
20. y cleaning routine Remove the top panel and clean to bare metal the fire damper and fan Do section with a clean dry cloth or absorbent paper towels See Figure 12A and 12B Figure 124 Remove top panel l and fire damper By Re install the clean dry fire damper and re install the top panel MTI Form OP 0005 Rev 002 7 98 E 23 167654 AUTOFRY Models MTI 5 Rev 2 Operator s Manual Charcoal Filter VERY IMPORTANT _s n order for the AUTOFRY tocontinue to perform as a ventless cooking appliance the charcoal filter medium or activated charcoal must be changed a minimum of every three months This maintenance is required by your equipment warranty While replacing the charcoal medium is easy there will be some charcoal dust present Replacing the charcoal medium should be performed away from your food preparation areas al Remove the charcoal filter D Remove the four screws holding the perforated cover m e Pour the used charcoal into a suitable container e Clean the re usable housing and perforated screen to bare metal in warm soapy water followed by a clear water rinse e Thoroughly dry the housing and cover a Pour the new charcoal into the housing and re seat the cover and O screws l Replace the charcoal filter and all the filter components All activated carbons do not have the same performance characteristics Use replacement charcoal supplied by AUTOFRY which can be ordered by calling 1 800 348 2976 Second F
Download Pdf Manuals
Related Search