Home
Emulex LP8000 (11803135507) Network Adapter
Contents
1. EMU LEX copyright Emulex Corporation all rights reserved 2002 Emulex Drivers Software and Manuals Attach Media Attach fibre optic or copper cable to the host bus adapter Attach Fiber Optic Cable Multi Single Mode Note The host adapter will not allow normal data transmission on an optical link unless it is connected to another similar or compatible laser product that is multimode to multimode Use fiber optic cable supporting a data rate of 1 0625 Gb s for short wave and long wave lasers that adheres to the following specifications Fiber Optic Cable Maximum Minimum Connector Length Length 62 5 125 U m 175 meters 2 meters Dual SC multimode 50 125 u m multimode 500 meters 2 meters Dual SC 9 125 u m single mode 10 000 meters 2 meters Dual SC 1 Connect the fiber optic cable to the dual SC connector on the host adapter board as shown 2 Connect the other end of the cable to the Fibre Channel device After the media is connected to the host adapter you are ready to apply power to the computer EMU LEX copyright Emulex Corporation all rights reserved 2002 Emulex Drivers Software and Manuals Attach Copper Duuplex Cable Use copper Twinax or Quad Axial cable that adheres to the following secifications Cable Type Maximum Length Data Rate Twinax or Quad Axial 1 0625 Gb s 3 1 Connect the copper duplex cable to the DB9 connector on the host
2. e One open 32 bit or 64 bit recommended PCI bus slot with a 3 3 VDC or 5 0 VDC signaling interface e Maximum PCI bus clock rate of 33 MHz e Media and connectors user supplied Multimode fiber optic cable 50 125 u m or 62 5 125 u m with dual SC connectors used with short wave lasers Single mode fiber optic cable 9 125 u m with dual SC connectors used with long wave lasers Copper duplex cabling with DB9 connectors also called DE9 v EMU LEX copyright Emulex Corporation all rights reserved 2002 Emulex Drivers Software and Manuals Set Jumpers The host adapter has two jumper blocks JX1 JX2 that control the host adapter s device ID The default Device ID is F800 Device ID 1AE5 zv eann ew lll S EMULEX copyright Emulex Corporation all rights reserved 2002 Emulex Drivers Software and Manuals Install Host Bus Adapter Board Record IEEE address and serial number Each host adapter is shipped with a unique address identifier called the IEFE address The Fibre Channel industry uses a World Wide Name WWN derived from the IEEE address and this number is need for arbitrated loop connectivity The serial number is used when communicating with Emulex Both numbers are clearly marked on the board We recommend that you record these numbers before installation Turn off and unplug the computer Remove the computer case Remove the blank panel from an empty 32 or 64 bit PC
3. Emulex Corporation all rights reserved 2002 22 Emulex Drivers Software and Manuals maintenance service operations or adjustments can be performed the GBIC Small Form Factor Transceiver The small form factor transceiver is an integrated duplex data link for bi directional communications over multimode or single mode optical fiber Each small form factor transceiver consists of a transmitter and receiver optical subassembly The transmitter subassembly contains a semiconductor laser emitting in the wavelength range of 770 to 860 nanometers for shortwave length small form factor transceivers and 1270 to 1355 nanometers for long wavelength small form factor transceivers For non OFC links the optical power from the laser transmitter is controlled and maintained at a lower power level The power emitted from either an open fiber or open laser transmitter is guaranteed to be below the Class 1 limit Class 1 laser products are not considered hazardous No user maintenance service operations or adjustments can be performed the small form factor transceiver 1x9 Transceiver The 1x9 transceivers is an integrated duplex data link for bi directional communications over multimode fiber Each 1x9 consists of a transmitter and receiver optical subassembly The transmitter subassembly contains a semiconductor laser emitting in the wavelength range of 770 to 860 nanometers for shortwave 1x9s For non OFC links the optical power from the las
4. Fax 44 118 977 3237 Fishponds Road Wokingham Berkshire RG41 2FD England FC1055001 07B February 2000 v EMU LEX copyright Emulex Corporation all rights reserved 2002 18 Emulex Drivers Software and Manuals Laser Safety Notice This laser safety information contains certification and product information covering laser products known as optical Gigabaud Link Modules GLMs Gigabit Interface Converters GBICs 1x9 and small form factor transceivers sold as accessories to or incorporated in Emulex LightPulse host adapters The GLM GBIC 1x9 and small form factor transceiver are the primary cable connection mechanisms for any optical port on the host adapter and hub This data is not intended to be a replacement for any safety regulations and standards relevant safety documents should always be consulted if necessary Contact Emulex Corporation with any questions or concerns about laser safety Certification and Classification Labeling Requirements Product Information Usage Restrictions System Level Certification Certification and Classification LP6000 and LP7000E PCI host adapters may contain a laser product known as an optical Gigabaud Link Module GLM The optical GLM is attached to the host adapter using an 80 pin connector and extends through the mounting bracket In turn the host adapter can be inserted into any host system s PCI slot The LH5000 hub may contain a laser product known as a Gigabi
5. by Emulex Corporation could void your authority to operate this equipment LP8000 N1 L1 T1 F1 GBIC and 1x9 Models TOENI WLS BEES EAR VCC oE SCP SAAS OS COO RAR COMETS Le WRENS BITLEMHVET TBD MURA ete HES SZLIBKRANALCL RAVES Translation This is a Class B product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment VCCI If this equipment is used near a radio or television receiver in a domestic environment it may cause radio interference Install and use the equipment according to the instruction manual LP8000 D1 Embedded Copper Model CORR P7AAPHRMNRETT ORME KER CN O CMG eie ETTI Layi coma sl a HR CMTS LPR IHS LHS ET Translation This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures VCCI A nr EMULEX copyright Emulex Corporation all rights reserved 2002 15 Emulex Drivers Software and Manuals Manual Notice TDA HL ARAL EEG AEB ae YCC ede IES CP SHATTERS LONE E eR CMTS Lie WPBCUSRITLLMHOKRT Toer Ae tM Tite aS HLABKARSALLMBAVET Translation This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment VCCI If this equipment is used in a domestic environment radio disturbance may arise When such trouble occurs the user may be required to take corr
6. for non OFC GLMs a compatible laser device must be non OFC Any system level product that incorporates the GLM must provide power supply protection that guarantees a voltage of 6 0 volts or less at the GLM The functional power supply range of the GLM product is specified as 4 75 to 5 25 volts typically Operation outside of this range may degrade the performance and lifetime of the GLM The GLM will remain operational with laser emissions below Class 1 limits provided the power supply level at the adapter remains at or below 6 0 volts If the power supply level rises above 6 0 volts the GLM cannot be guaranteed to operate correctly and could result in laser emissions that may exceed Class 1 limits GBIC Short wavelength and long wavelength GBICs allow normal data transmission on the optical link when they are connected to another compatible laser product Short wavelength and long wavelength GBICs sold by Emulex as accessories are non OFC devices For non OFC links a compatible laser device must be non OFC and certified as a Class 1 laser product 1 x 9 Transceiver Short wavelength 1x9 transceivers allow normal data transmission on the optical link when they are connected to another compatible laser product Short wavelength 1x9s embedded in Emulex host adapters are non OFC For non OFC links a compatible laser device must be non OFC and certified as a Class 1 laser product Small Form Factor Transceiver Short wavele
7. x 4 20 11 watts 5 0 VDC typical 100 lfm minimum Temperature Operating K2 to 113 F 0 to 45 C Storage l4 to 131 F 10 to 55 C Humidity 5 to 95 non condensing Agency Approvals for UL recognized to UL1950 LP8000 D1 CUR recognized to CSA22 2 No 950 TUV certified to EN60950 FCC Rules Part 15 Class A Industry Canada ICES 003 Class A EMC Directive 89 336 EEC CE Mark EN55022 Class A EN50082 1 Australian EMC Framework C Tick Mark AS NZS 3548 Class A VCCI Class A Agency Approvals for Class 1 Laser Product per DHHS 21CFR J amp EN60825 LP8000 N1 T1 L1 UL recognized to UL1950 and LP8000 F1 CUR recognized to CSA22 2 No 950 TUV certified to EN60950 FCC Rules Part 15 Class B Industry Canada ICES 003 Class B EMC Directive 89 336 EEC CE Mark EN55022 Class B EN50082 1 Australian EMC Framework C Tick Mark AS NZS 3548 Class B VCCI Class B EMU LEX copyright Emulex Corporation all rights reserved 2002 Hardware Reference Copper Port DB9 Pinout This pinout applies to embedded copper ports Signal Direction TX Output VCC VCC Fautt Input NOS ODIS Output GND GND RX Input A D lt vn Emulex Drivers Software and Manuals Hardware Reference FCC and Regulatory Notices CLASS 1 LASER PRODUCT LASER KLASSE 1 LUOKAN 1 LASERLAITE APPAREIL A LASER DE CLASSE 1 TO IEC 825 1 1993 CENELEC HD 4
8. 82 S1 The above statement applies to products marketed in the European Union Model LP8000 D1 Embedded Copper This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Shielded cables must be used between this equipment and attached peripheral devices The reader is cautioned that changes or modifications made to the equipment not expressly approved by Emulex could void the user s authority to operate this equipment The above statement applies to products marketed in the USA This class A digital apparatus meets all requirements of the Canadian Interference Causing Equipmen
9. 977 2929 Oaklands Park Fax 44 118 977 3237 Fishponds Road Wokingham Berkshire RG41 2FD England EMU LEX copyright Emulex Corporation all rights reserved 2002 Emulex Drivers Software and Manuals This equipment complies with CISPR22 EN55022 Class A Warning This is a class A product In a domestic environment this product may cause radio interference requiring the user to take adequate measures This Declaration identifies the product manufacturer s name and address and applicable specifications recognized in the European Union DECLARATION OF CONFORMITY Manufacturer Emulex Corporation 3535 Harbor Blvd Costa Mesa CA 92626 USA declares under sole responsibility that the product Product LightPulse LP8000 Fibre Channel PCI Host Adapter Name Assembly FC1020019 XX Embedded DB9 model Number to which this declaration relates is in conformity with the following standards or other documents Safety IEC950 1991 A1 A2 EN60950 1992 A1 A2 TUV Rheinland Certificate No R9677151 1 EMC EN55022 1994 CISPR 22 1993 Class A EN50082 1 1997 following the provisions of the Low mae j us Voltage Directive 73 23 EEC and EMC Patrols Se Sree Directive 89 336 EEC as amended by 92 31 EEC and is Marked in accordance with the CE Marking Directive 93 68 EEC November 25 1998 Costa Mesa CA European Contact Emulex Corporation Telephone 7 amp 8 Forrest Court 44 118 977 2929 Oaklands Park
10. Emulex Drivers Software and Manuals 53 EMULEX We network storage LP8000 Installation and Reference Manual Table of Contents Installation Compatability Prerequisites Set Jumpers Install HBA Change GBIC Attach Media Apply Power View LEDs Reference Specifications DB9 Pinout FCC and Regulatory Notices Declaration of Conformity Laser Safety v EMU LEX copyright Emulex Corporation all rights reserved 2002 Emulex Drivers Software and Manuals h r 1 Installation Table of Contents Compatability Prerequisites Set Jumpers Install HBA Change GBIC Attach Media Apply Power View LEDs EMU LEX copyright Emulex Corporation all rights reserved 2002 Emulex Drivers Software and Manuals Installation Caution Emulex LightPulse Host Bus Adapters HBAs contain electronic components that can be damaged by static electricity through an electrostatic discharge ESD event To prevent ESD damage maintain frequent contact with any grounded metal surface A grounding wrist strap is useful for this purpose Handle the card carefully at all times and preferably by the edges Avoid touching electronic components and keep the card in the original packaging until you are ready for installation Compatibility Software Windows Server 2003 Windows 2000 Windows NT Environments NetWare HP UX Linux Solaris AlX Hardware PCI hardware platforms x86 SPARC and PowerPC Environments Prerequisites
11. I bus slot Insert host adapter board into the empty 32 or 64 bit PCI bus slot Press firmly until the board is seated 6 Secure the host adapter s mounting bracket to the case with the panel screw 7 Replace the computer case and tighten case screws nb WN The host adapter is now installed in the PC and is ready for media attachment EMU LEX copyright Emulex Corporation all rights reserved 2002 Emulex Drivers Software and Manuals Change the GBIC Connector A GBIC or Gigabit Interface Converter is a connector that offers a flexible choice of copper or fiber optic media A GBIC supports either short wave or long wave optical transmission These types are available e Short wave fiber optic GBIC with dual SC connectors e Long wave fiber optic GBIC with dual SC connectors e Copper GBIC with DB9 connector Caution An Emulex supplied GBIC is required to maintain regulatory compliance with worldwide certifications for example FCC C Tick CE and so on A GBIC should be matched with its cabling to obtain optimum performance and distance For example a short wave fiber optic GBIC best supports either 62 5 125 or 50 125 multimode cable while a long wave fiber optic GBIC functions best with 9 125 single mode cable To change a GBIC 1 Exert slight pressure on the tabs 2 Gently pull out the GBIC as shown 3 Slide in a new GBIC pressing firmly to seat the GBIC into the board
12. adapter board as shown 2 Connect the other end of the cable to the Fibre Channel device After the media is connected to the host adapter you are ready to apply power to the computer EMU LEX copyright Emulex Corporation all rights reserved 2002 Emulex Drivers Software and Manuals Apply Power 1 Verify that the host adapter is securely installed in the computer 2 Verify that correct media is attached 3 Plug in and turn on the computer 4 Observe LEDs for Power On Self Test POST results View LEDs a E mbedded optical port LED Green and yellow display lights LEDs can be seen through openings in the host adapter s mounting bracket Green indicates power and yellow signifies port activity A third LED is present on LP8000 models with embedded optical interfaces and indicates that light is being received by the port 66o POST conditions and results are summarized in this table LED LED OFF Failure while functioning ON F F F F F EMU LEX copyright Emulex Corporation all rights reserved 2002 EMULEX Emulex Drivers Software and Manuals Chapter 2 Reference Table of Contents DB9 Pinout FCC and Regulatory Notices Declaration of Conformity Laser Safety copyright Emulex Corporation all rights reserved 2002 11 Emulex Drivers Software and Manuals Hardware Reference Specifications 20 pin connector for GBIC models Short PCI form factor 6 88
13. ansceivers sold by Emulex are certified as Class 1 laser component assemblies that conform to the requirements contained in the CENELEC European Committee for Electrotechnical Standardization standard EN60825 1 1994 including amendment 11 and EN60825 2 1994 GLMs GBICs 1x9 and small form factor transceivers are certified by a recognized European testing agency and have appropriate markings on the assembly The DHHS conformity label and European conformity mark will not be visible externally once the optical GLM GBIC 1x9 or small form factor transceiver is connected to or inserted in the host adapter and the adapter is installed into a system Labeling Requirements No caution or danger labels are required for use of the GLM GBIC 1x9 or small form factor transceiver since they are Class 1 laser component assembly In the U S the only laser safety label required is the DHHS certification label that already appears on the GLM GBIC 1x9 and small form factor transceiver In Europe the EN60825 1 EN60825 2 standards require that the system level product has a Class 1 information label permanently attached and clearly visible whenever access to the GLM GBIC 1x9 and small form factor transceiver optical port is possible Each Class 1 product shall have affixed an explanatory label bearing the words CLASS 1 LASER PRODUCT Alternatively at the discretion of the manufacturer the same statement may be included in user informa
14. ective actions v eanan mea _ _ _ 2 EMU LEX copyright Emulex Corporation all rights reserved 2002 16 Emulex Drivers Software and Manuals Hardware Reference Declaration of Conformity Note Changes or modifications not expressly approved by Emulex Corporation could void the user s authority to operate this equipment DECLARATION OF CONFORMITY Manufacturer Emulex Corporation 3535 Harbor Blvd Costa Mesa CA 92626 USA declares under sole responsibility that the product Product LightPulse LP8000 Fibre Channel PCI Host Adapter Name Assembly FC1020017 XX GBIC model Number FC1020016 XX embedded optical 1x9 model Accessories Emulex PN 2300029 Active Copper DB9 GBIC Module Emulex PN 2300028 Shortwave Optical GBIC Module Emulex PN 2300030 Longwave Optical GBIC Module to which this declaration relates is in conformity with the following standards or other documents Safety IEC950 1991 A1 A2 EN60950 1992 A1 A2 including EN60825 1 1994 TUV Rheinland Certificate No R9677151 1 EMC EN55022 1994 CISPR 22 1993 Class A EN50082 1 1997 following the provisions of the Low ii 4 us Voltage Directive 73 23 EEC and EMC PASE aS Ise amp LED Directive 89 336 EEC as amended by 92 31 EEC and is Marked in accordance with the CE Marking Directive 93 68 EEC February 18 1999 Costa Mesa CA European Contact Emulex Corporation Telephone 7 amp 8 Forrest Court 44 118
15. er transmitter is controlled and maintained at a lower power level The power emitted from either an open fiber or open laser transmitter is guaranteed to be below the Class 1 limit Class 1 laser products are not considered hazardous No user maintenance service operations or adjustments can be performed the 1x9 transceiver Usage Restrictions Failure to comply with these usage restrictions may result in incorrect operation of the system and could possible lead to points of access that may emit laser radiation levels above the Class 1 limits established in the U S by the DHHS and within Europe by EN60825 1 EN60825 2 GLM GBIC 1 x 9 Transceiver Small Form Factor Transceiver v EMU LEX copyright Emulex Corporation all rights reserved 2002 23 Emulex Drivers Software and Manuals GLM The GLM is designed and certified for applications using point to point optical fiber links only Use of the product with multiple input or multiple output optical links for example star couplers is prohibited since it is incompatible with the GLM s certification The GLM will not allow normal data transmission on the optical link unless it is connected to another similar GLM or compatible laser product For OFC GLMs another manufacturer s laser product is not considered compatible unless it contains the open fiber link detection and laser safety control system OFC and is properly certified as a Class 1 laser product Similarly
16. ergy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help nr EMU LEX copyright Emulex Corporation all rights reserved 2002 14 Emulex Drivers Software and Manuals The reader is cautioned that any changes or modifications to the equipment not expressly approved by Emulex could void the user s authority to operate this equipment This class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Cet Appareil numerique de la classe B respecte toutes les exigences du reglement sur le material brouilleur du Canada The above statement applies to products marketed in Canada VCCI Notices and Translations Japan Only Note VCCI regulations provide that changes or modifications not expressly approved
17. ngth and long wavelength small form factor transceivers allow normal data transmission on the optical link when they are connected to another compatible laser product Short wavelength and long wavelength small form factor transceivers embedded in Emulex host adapter are non OFC For non OFC links a compatible laser device must be non OFC and certified as a v EMU LEX copyright Emulex Corporation all rights reserved 2002 24 Emulex Drivers Software and Manuals Class 1 laser product Any system level product that incorporates the small form factor transceivers must provide power supply protection that guarantees a voltage of 5 0 volts or less at the small form factor transceivers The functional power supply range of the small form factor transceivers product is specified as 3 135 to 3 465V typically Operation outside of this range may degrade the performance and lifetime of the transceiver The transceiver will remain operational with laser emissions below Class 1 limits provided the power supply level at the adapter remains at or below 5 0 volts If the power supply level rises above 5 0 volts the small form factor transceiver cannot be guaranteed to operate correctly and could result in laser emissions that may exceed Class 1 limits EMU LEX copyright Emulex Corporation all rights reserved 2002 25 Emulex Drivers Software and Manuals System Level Certification All GLMs and GBICs sold as accessories by Em
18. only to the LP6000 and not to the LP7000E LP8000 LP850 or LP9000 For OFC GLMs Open Fiber Control the optical fiber link between two GLM ports is continuously monitored by the open fiber link detection and laser safety control system OFC In the event of a break anywhere in the path this control system prevents laser emissions from exceeding Class 1 levels For non OFC links the optical power from the laser transmitter is controlled and maintained at a lower power level The power emitted from either an open fiber or open laser transmitter is guaranteed to be below the Class 1 limit Class 1 laser products are not considered hazardous No user maintenance service operations or adjustments can be performed on any GLM accessory GBIC The optical GBIC is an integrated duplex data link for bi directional communications over multimode or single mode optical fiber Each GBIC consists of a transmitter and receiver optical subassembly The transmitter subassembly contains a semiconductor laser emitting in the wavelength range of 770 to 860 nanometers for shortwave length GBICs and 1270 to 1355 nanometers for long wavelength GBICs For non OFC links the optical power from the laser transmitter is controlled and maintained at a lower power level The power emitted from either an open fiber or open laser transmitter is guaranteed to be below the Class 1 limit Class 1 laser products are not considered hazardous No user v EMU LEX copyright
19. t Interface Connector GBIC The GBIC provides the physical connector to the optical cable The GBIC can be inserted into any pluggable hub port The LP8000 LP850 and LP9000 PCI host adapter may contain a laser product known as a Gigabit Interface Converter GBIC or an embedded 1x9 transceiver The GBIC and or 1x9 transceiver provide the physical connection to the optical cable and its SC style connector extends through the mounting bracket In turn the host adapter can be inserted into any host system s PCI slot The LP9002 LP9002L LP952L LP9002S LP9002DC LP9002C and LP9402DC PCI host adapters may contain a laser product known as a small form factor transceiver This transceiver provides the physical connection to the optical cable and its LC style connector extends through the mounting bracket In turn the host adapter can be inserted into any host system s PCI cPCI slot In the United States all optical GLMs GBICs 1x9 and small form factor transceivers sold by Emulex are certified as Class 1 laser products that conform to the requirements contained in the Department of Health and Human Services DHHS regulation 21 CFR subchapter J The certification is indicated by a label located on the optical GLM GBIC 1x9 or small form factor transceiver v EMU LEX copyright Emulex Corporation all rights reserved 2002 20 Emulex Drivers Software and Manuals In Europe all optical GLMs GBICs 1x9 and small form factor tr
20. t Regulations Cet appareil numerique de la Classe A respecte toutes les exigences du reglement sur le materiel brouilleur du Canada This statement applies to products marketed in Canada FCC Compliance Information Statement Models LP8000 N1 L1 T1 GBIC Models v EMU LEX copyright Emulex Corporation all rights reserved 2002 13 Emulex Drivers Software and Manuals LightPulse LP8000 Fibre FC1020017 Channel Host Adapter Tested to Comply With FCC Standards FOR HOME OR OFFICE USE FCC Compliance Information Statement Model LP8000 F1 1 X 9 LightPulse LP8000 Fibre FC1020016 Channel Host Adapter Tested to Comply With FCC Standards FOR HOME OR OFFICE USE This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Responsible Party Paul Folino President amp CEO Emulex Corporation 3535 Harbor Blvd Costa Mesa CA 92626 USA 714 662 5600 Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency en
21. tion If a label is used an example of the IEC Class 1 information label that is suitable for most European countries is shown below The label consists of black printing on a white background Languages represented on this label are English German Finnish and French and they represent the minimum set for acceptance of a Class 1 product in most European countries CLASS 1 LASER PRODUCT LASER KLASSE 1 LUOK AN 1 LASERLAITE APPAREIL amp LASER DE CLASSE 1 nr EMU LEX copyright Emulex Corporation all rights reserved 2002 24 Emulex Drivers Software and Manuals Product Information GLM GBIC 1 x 9 Transceiver Small Form Factor Transceiver GLM The optical GLM is a single port communications card Each communication port consists of a transmitter and receiver optical subassembly The transmitter subassembly contains a semiconductor laser diode of gallium aluminum arsenide GaAlAs This material emits in the wavelength range of 770 to 860 nanometers for shortwave and 1270 to 1355 nanometers for long wave and are commonly referred to as short wavelength SW or long wavelength LW lasers The discrete laser diodes are classified as Class 3B laser products Once they are incorporated into the GLM the product s automatic power control maintains the average power launched into a fiber at a value below the Class 1 limit Note OFC GLMs are found only on the LP6000 Any reference to OFC or non OFC products applies
22. ulex or host adapters containing embedded 1x9 or small form factor transceivers are certified as Class 1 laser products within the U S and Class 1 laser component assemblies outside of the U S Manufacturers of products properly incorporating the GLM GBIC 1x9 or small form factor transceiver do not need to recertify their product for laser safety The procedure for full system certification is therefore identical to that used for any other electronic system When applying for system level certification to electronic standards such as IEC950 the regulatory engineers may want to see the DHHS and European conformity labeling on the GLM GBIC 1x9 or small form factor transceiver and the system level documentation and labeling Copies of the certificate of conformity for any GLM GBIC 1x9 or small form factor transceiver sold by Emulex can be obtained upon request from Emulex Corporation Costa Mesa EMU LEX copyright Emulex Corporation all rights reserved 2002 26
Download Pdf Manuals
Related Search
Related Contents
GPO 14 CE Professional boite 51 passion Manual de Usuario Anatomia Patologica HRR V3-2015 サニックス(4651) User manual OM, BLi520x, BLi940x, 2014-03, EN, SE, DK, NO, FI ib-trasponder8 Samsung SGH-F490V User Manual manuale uso e manutenzione testa a satelliti use and Copyright © All rights reserved.
Failed to retrieve file