Home

Samsung SyncMaster 915N 19" Flat Panel LCD Monitor

1. AUTO SOURCE Description When the AUTO button is pressed the Auto Adjustment screen appears as shown in the animated screen on the center Auto adjustment allows the monitor to self adjust to the incoming video signal The values of fine coarse and position are adjusted automatically Available in analog Mode Only To make the automatic adjustment function sharper execute the AUTO function while the AUTO PATTERN is on e f Auto Adjustment does not work properly press Auto button again to adjust picture with more accuracy e f you change resolution in the control panel Auto function will be executed automatically O MagicBright SOURCE Menu Description MagicBright Then push the MagicBright button again to circle through available preconfigured modes four different modes Custom T ext Internet Entertain Brightness SOURCE Menu Description Brightness Adjust Brightness Source SOURCE Menu Description Source Selects the Video signal while the OSD is off User Control Buttons Direct Functions OSD Functions Mla MagicTune 1 Picture Brightness Contrast 2 Color BI Color Tone Color Control 3 Image i coarse Fine Sharpness H Posiion V Posiion 4 osp ES Language _ H Postton v Posiion Transparency _ Display Time 5 Setup BE Auto Source image Reset Color Rese 6 Information Picture F Menu Desc
2. The best way to protect your monitor from Image retention is to set your PC or System to operate a Screen Saver program when you are not using it Image retention may not occur when a LCD panel is operated under normal conditions Normal conditions are defined as continuously changing video patterns When the LCD panel is operated for a long time with a fixed pattern over 12 hours there may be slight difference in voltage between electrodes that work the liquid crystal LC ina pixel The voltage difference between electrodes increases with time forcing the liquid crystal to lean When this occurs the previous image may be seen when the pattern is changed To prevent this the accumulated voltage difference must be decreased Common Electrode ITO Color Filter Pixel Electrode Storage Capacitor ITO 5 HERA A A AH I Our LCD Monitor satisfies ISO13406 2 Pixel fault Class II
3. ES ttr bb A Window a Wings gt gt d Natural Color kb uy E iowa gt mye MagicTune SyncMaster 913N 915N 912T WITT everyone s invi Notational Power Installation Clean Others l Please read the following safety instructions as they are designed to prevent damage to property and harm to the user Kag Warning Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment EB Notational Conventions Prohibited Important to read and understand at all times Disconnect the plug from the outlet Do not disassemble Do not touch Grounding to prevent an electric shock O Go Notational Power Installation Clean Others Power When not used for extended period of time set your computer to DPMS If using a screen saver set it to the active screen mode 3 Do not use a damaged or loose plug e This may cause an electric shock or fire 3 Do not pull the plug out by the wire nor touch the plug with wet hands e This may cause an electric shock or fire 2 Use only a properly grounded plug and receptacle e An improper ground may cause electric shock or equipment damage 3 Do not excessively bend the plug and wire nor place heavy objects upon them which could cause damage e This may cause an electric shock or fire 2 Do not connect too many extension cords or plugs to an outlet e his may cause fire Notati
4. 5 If you have problems in installing the adapter video driver boot the computer in Safe Mode remove the Display Adapter at the Control Panel System Device Administrator and then reboot the computer to reinstall the adapter video driver aaa Pama a Lv Y If problems repeatedly occur contact an authorized service center Mm Check List Q amp A Self Test Feature Check Q amp A Question Answer How can change the Frequency can be changed by reconfiguring the video card frequency Note that video card support can vary depending on the version of the driver used Refer to the computer or the video card manual for details How can adjust the resolution Windows ME XP 2000 Set the resolution at the Control Panel Display Settings Contact the video card manufacturer for details How can set the Power Saving Windows ME XP 2000 Set the function at BIOS SETUP of the function computer or the screen saver Refer to Windows Computer Manual How can clean the outer Disconnect the power cord and then clean the monitor with a soft case LCD Panel cloth using either a cleaning solution or plain water Do not leave any remains of the detergent nor scratch the case Do not allow any water to go inside the monitor Check List Q amp A Self Test Feature Check Self Test Feature Check Self Test Feature Check Warning Messages Environment Useful Tips Your monitor provides a self test f
5. Warning Messages If there is something wrong with the input signal a message appears on the screen or the screen goes blank although the power indicator LED is still on The message may indicate that the monitor is out of scan range or that you need to check the signal cable Not Optimum Mode Recommended Mode 1280 x 1024 60Hz Environment The location and the position of the monitor may influence the quality and other features of the monitor 1 If there are any sub woofer speakers near the monitor unplug and relocate the woofer to another room 2 Remove all electronic devices such as radios fans clocks and telephones that are within 3 feet one meter of the monitor Useful Tips e A monitor recreates visual signals received from the computer Therefore if there is trouble with the computer or the video card this can cause the monitor to become blank have poor coloring noise Video mode not supported etc In this case first check the source of the problem and then contact the Service Center or your dealer e Judging the monitor s working condition If there is no image on the screen or a Not Optimum Mode Recommended Mode 1280 x 1024 60Hz message comes up disconnect the cable from the computer while the monitor is still powered on o If there is a message coming up on the screen or if the screen goes white this means the monitor is in working condition o In this case check the computer for trouble
6. Driver installation is slightly different from one operating system to another Follow the directions appropriate for the operating system you have Prepare a blank disk and download the driver program file at the Internet web site shown here e Internet web site http www samsung com Worldwide http www samsungusa com monitor USA http www sec co kr monitor Korea http www samsungmonitor com cn China Microsoft Windows XP Operating System 1 Insert CD into the CD ROM driver 2 Click Start gt Control Panel then click the Appearance and Themes Icon Fh HE eee ee Ha Q O S P re m Peete rrr aaah Cepler E ray Documents adios tmm Kap em een comen s gg Pete Firbas wt PET 0 0 Kb ray musie a Makapad W Padre C Andora bodies Mara E e MESH Inger Lor Hop and 5uoport p Search Low Andon Movi lo dar F kun FARE Programe L 3 Click Display icon and choose the Settings tab then click Advanced Eh EF fee Aprii be Hee nla Oo ci ii dl Mp ipp mme r ed ieee D aut Pick a task A A b Ms Ng did a rr P ar rr E Pe rion ie cue n ea o Dipsas or pick a Control Fanel icon O Fim eed Pas Heras core DER ropi dil Gaman de and iens p E PP D LIE Than Tu apomaba ee a Sh mimm mem cob ka Eel EE Plug and Play Monitor and 40 Prophet Properties Geo Selection Color Consction Geral Duiwe General Adapter Morelos Tr
7. Svenska Naturskyddsforeningen The Swedish Society for Nature Conservation Statens Energimyndighet The Swedish National Energy Administration and SEMKO AB The requirements cover a wide range of issuse environment ergonomics usability reduction of electric and magnetic fields energy consumption and electrical safety Why do we have environmentally labelled computers In many countries environmental labelling has become an established method for encouraging the adaptation of goods and services to the environment The main problem as far as computers and other electronics equipment are concerned is that environmentally harmful substances are used both in the products and during their manufacture Since it is not so far possible to satisfactorily recycle the majority of electronics equipment most of these potentially damaging substances sooner or later enter nature There are also other characteristics of a computer such as energy consumption levels that are important from the viewpoints of both the work internal and natural external environments Since all methods of electricity generation have a negative effect on the environment e g acidic and climate influencing emissions radioactive waste it is vital to save energy Electronics equipment in offices is often left running continuously and thereby consumes a lot of energy What does labelling involve The environmental demands has been developed by Svenska Naturskyddsforening
8. 210 1133 Tel 800 3278 FAST http www samsung latin com PERU Servicio Integral Samsung Av Argentina 1790 Lima1 Peru Tel 51 1 336 8686 Fax 51 1 336 8551 http www samsungperu com PORTUGAL SAMSUNG ELECTRONICA PORTUGUESA S A Rua Mario Dioniso N92 1 Drt 2795 140 LINDA A VELHA Tel 214 148 114 100 Fax 214 148 133 128 Free Line 800 220 120 http www samsung pt SOUTH AFRICA Samsung Electronics 5 Libertas Road Somerset Office Park Bryanston Ext 16 Po Box 70006 Bryanston 2021 South Africa Tel 0027 11 549 1621 Fax 0027 11 549 1629 http www samsung co za SWEDEN DENMARK NORWAY FINLAND Samsung Electronics AB Box 713 S 194 27 UPPLANDS VASBY SVERIGE Besoksadress Johanneslundsvagen 4 Samsung support Sverige 020 46 46 46 Samsung support Danmark 8088 4646 Samsung support Norge 8001 1800 Samsung support Finland 0800 118001 Tel 46 8 590 966 00 Fax 46 8 590 966 50 http www samsung se THAILAND HAI SAMSUNG SERVICE CENTER MPA COMPLEX BUILDING 1st 2nd Floor 175 SOI SUEKSA VIDHAYA SATHON SOI 12 SILOM ROAD SILOM BANGRAK BANGKOK 10500 TEL 0 2635 2567 FAX 0 2635 2556 UKRAINE SAMSUNG ELECTRONICS REPRESENTATIVE OFFICE IN UKRAINE 4 Glybochitska str Kiev Ukraine Tel 8 044 4906878 Fax 8 044 4906887 Toll free 8 800 502 0000 http www samsung com ua United Kingdom Samsung Electronics UK Ltd Samsung House 225 Hook Rise South Surbiton Surrey KT6 7L
9. Inc Windows is a registered trademark of Microsoft Corp Other trademarks are property of their respective holders Magiclune HELP TI l Overview Installation OSD Mode or install T leshooti Calibration Uninstall Troubleshooting Color Calibration 1 Color Calibration a NC a nw A INS T Magicfune co rE Color Launch Calibration Color Calibration guides you to get optimal color condition for your monitor Proceed following 5steps for getting optimal monitor color condition 1 Control Brightness control bar for matching the brightness of control patch and the brightness of background pattern 2 When you detect specific color tone on Control patch move the control cursor toward to the direction of the color tone referring to Color reference Circle gt Adjustment is finished properly you won t detect any color tone on Control patch 3 When you finish adjustment for step1 Click Next button 4 Repeat 1 2 3 procedures for remaining step2 step5 5 You can easily view the calibration effect through clicking Preview button How multiple users can use adjusted color values Definition When monitor is used by multiple users color values which are adjusted via Color calibration for each users can be saved and used Up to 5 users can use the saved color values 1 How to save adjusted color values Press Next to make it change into Apply and then you can save adjusted co
10. L207 Mak owedaster CX LI Seo avr re tari ge ep Lila E we lari Law GL PG LAN a MANG 107 1 Magic rela Lor Cx 109 A Zoynicltaztos SIT 1857 1060 RET Mater Ca LOSE ArH mica on 101 T LOST LOOT Fook SyncMaster CA LOSE Ci Gre Ata APT AAA Na Samang Ar SLOT Rabe oua Ge ee Ca wel GE 4 If you can see following message window then click the Continue Anyway button Then click OK button Hardware Installation The rofwasre vou ann nmboling foe this haa drena Tynk acter 1715 1755 1705 Hog bun Masha C01 755 has not pagsed Windows Logo heating bo wendy iia compabbdiy wath Anao SP T e mg why this bagting is mentari Continuing pom installation of this software map imper or destabilize the conmecl operation of your spebem ether immediately or sm the future Microsoft bona s commonds lhal pou tiop this inalallabon now and i h vers wenda bor aolivwarn thal haz beating V This monitor driver is under certifying MS logo and this installation don t damage your system The certified driver will be posted on Samsung Monitor Homepage http www samsung com 5 Monitor driver installation is completed Connecting the Monitor Using the Stand Installing the Monitor Driver Installing the Monitor Driver Natural Color i Automatic Manual Windows XP Windows 2000 Windows Me Windows NT Linux Y When prompted by the operating system for the monitor driver insert the CD ROM ER included with this monitor
11. LXXX ADDE CC Yr ta A Baa A BB BN everyone s invitec m Safety Instructions da E Setup E Adjusting Your Monitor Troubleshooting MB Specifications E Information Unpacking Front Rear Please make sure the following items are included with your monitor If any items are missing contact your dealer Unpacking 2 Option 1 Monitor amp Simple stand Bottom Option 2 Monitor 8 Pivot stand Manual e Warranty Card User s Guide ZI Not available in all Monitor Driver Quick Setup Guide locations Natural Color software MagicTune software 2 Cable D Sub Cable Power Cord Unpacking Front Rear Front SAMSUNG 1 Menu button I Opens the OSD menu Also use to exit the OSD menu or return to the previous menu 2 MagicBright button MagicBright is a new feature providing optimum viewing 45 environment depending on the contents of the image you are watching Currently four different modes are available Custom Text Internet and Entertain Each mode has its own pre configured brightness value You can easily select one of four settings by simply pressing MagicBright control buttons 1 Custom Although the values are carefully chosen by our engineers the pre configured values may not be comfortable to your eyes depending on your taste If this is the case adjust the Brightness and Contrast by using the OSD menu 2 Text Normal Brightness For documentations or works inv
12. are 3 932 160 Note Design and specifications are subject to change without prior notice General PowerSaver Preset Timing Modes 9 PowerSaver This monitor has a built in power management system called PowerSaver This system saves energy by switching your monitor into a low power mode when it has not been used for a certain amount of time The monitor automatically returns to normal operation when you press a key on the keyboard For energy conservation turn your monitor OFF when it is not needed or when leaving it unattended for long periods The PowerSaver system operates with a VESA DPMS compliant video card installed in your computer Use a software utility installed on your computer to set up this feature Power saving mode State Normal Operation EPA ENERGY 2000 Power Switch off Power Indicator Green Green Blinking Black Less than 1W Less than 1W Power Consumption Less than 38W Off mode 120Vac This monitor is EPA ENERGY STAR compliant and ENERGY2000 compliant when used with a computer equipped with VESA DPMS functionality As an ENERGY STAR Partner SAMSUNG has determined that this ENERGY STAR product meets the ENERGY STAR guidelines for energy efficiency General PowerSaver Preset Timing Modes Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes the screen will be adjusted automatically However if the signal differs the screen m
13. built in power management system called PowerSaver This system saves energy by switching your monitor into a low power mode when it has not been used for a certain amount of time The monitor automatically returns to normal operation when you press a key on the keyboard For energy conservation turn your monitor OFF when it is not needed or when leaving it unattended for long periods The PowerSaver system operates with a VESA DPMS compliant video card installed in your computer Use a software utility installed on your computer to set up this feature Power saving Normal mode Power off Operation EPA ENERGY Power button 2000 Power off Power Switch option Power Indicator Green Green Blinking Black Black Power Less than 38W Less than 1W Less than 1W Consumption Off mode 120Vac Bese Man UW This monitor is EPA ENERGY STAR compliant and ENERGY2000 compliant when used with a computer equipped with VESA DPMS functionality As an ENERGY STAR Partner SAMSUNG has determined that this ENERGY STAR product meets the ENERGY STAR guidelines for energy efficiency General PowerSaver Preset Timing Modes Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes the screen will be adjusted automatically However if the signal differs the screen may go blank while the power LED is on Refer to the video card manual and adjust the screen as follows Table 1 P
14. flame retardants are chemically related to another group of environmental toxins PCBs Both the flame retardants containing bromine or chloride and the PCBs are suspected of giving rise to severe health effects including reproductive damage in fish eating birds and mammals due to the bio accumulative processes Flame retardants have been found in human blood and researchers fear that disturbances in foetus development may occur The relevant TCO 99 demand requires that plastic components weighing more than 25 grams must not contain flame retardants with organically bound bromine or chlorine Flame retardants are allowed in the printed circuit boards since no substitutes are available Cadmium Cadmium is present in rechargeable batteries and in the colour generating layers of certain computer displays Cadmium damages the nervous system and is toxic in high doses The relevant TCO 99 requirement states that batteries the colour generating layers of display screens and the electrical or electronics components must not contain any cadmium Mercury Mercury is sometimes found in batteries relays and switches lt damages the nervous system and is toxic in high doses The relevant TCO 99 requirement states that batteries may not contain any mercury It also demands that mercury is not present in any of the electrical or electronics components associated with the labelled unit There is however one exception Mercury is for the time being permi
15. for you PEREA AAA Qin um 3 OSD Mode The OSD mode allows easy adjustment of monitor settings without taking pre defined steps You can access the desired menu item to set with ease Specifications subject to change without notice MagicTune is a trademark of SAMSUNG ELECTRONICS CO Inc Windows is a registered trademark of Microsoft Corp Other trademarks are property of their respective holders Magiclune HELP JI Overview Installation OSD Mode ET ninstall Troubleshooti Calibration Uninstal oubleshooting Installation 1 Insert the installation CD into the CD ROM drive 2 Click the MagicTune installation file 3 Select installation Language Click Next Choose Setup Language Welcome to the InstallShield Wizard for MagicTune 2 5 The InstallShield Wizard will install MagicT une 2 5 on pour computer To continue click Nest LI I a 5 Select agree to the terms of the license agreement to accept the terms of use 6 7 8 MagicTune 2 5 InstallShield Wizard License Agreement Please read the following license agreement carefully END USER LICENSE AGREEMENT FOR SAMSUNG ELECTRONICS MagicT une SOFTWARE PRODUCT IMPOR TANT READ CAREFULLY This Samsung Electronics End User License Agreement EULA is a legal agreement between vau ether an individual or a single entity and Samsung Electronics Co Ltd SAMSUNG ELECTRONICS with respec
16. operative project between 3 logos Environmental Requirements Brominated flame retardants are present in printed circuit boards cables wires casings and housings In turn they delay the spread of fire Up to thirty percent of the plastic in a computer casing can consist of flame retardant substances These are related to another group of environmental toxins PCBs which are suspected to give rise to similar harm including reproductive damage in fish eating birds and mammals due to the bioaccumulative processes Flame retardants have been found in human blood and researchers fear that disturbances in foetus development may occur e TCO 95 demand requires that plastic components weighing more than 25 grams must not contain organically bound chlorine and bromine Lead Lead can be found in picture tubes display screens solders and capacitors Lead damages the nervous system and in higher doses causes lead poisoning e TCO 95 requirement Permits the inclusion of lead since no replacement has yet been developed Cadmium Cadmium is present in rechargeable batteries and in the colour generating layers of certain computer displays Cadmium damages the nervous system and is toxic in high doses e TCO 95 requirement states that batteries may not contain more than 25 ppm parts per million of cadmium The colour generating layers of display screens must not contain any cadmium Mercury Mercury is sometimes found in batteries relays and sw
17. received from the computer Therefore if there is trouble with the computer or the video card this can cause the monitor to become blank have poor coloring noise Video mode not supported etc In this case first check the source of the problem and then contact the Service Center or your dealer e Judging the monitor s working condition If there is no image on the screen or a Not Optimum Mode Recommended Mode 1280 x 1024 60Hz message comes up disconnect the cable from the computer while the monitor is still powered on o If there is a message coming up on the screen or if the screen goes white this means the monitor is in working condition o In this case check the computer for trouble SyncMaster 913N po everyone s E Safety Instructions Introduction E Setup E Adjusting Your Monitor 8 Troubleshooting Jeti itt Information General PowerSaver Preset Timing Modes General General Model Name SyncMaster 913N LCD Panel Size 19 Diagonal Display area 376 32 H x 301 056 V Pixel Pitch 0 294mm H x 0 294mm V Type a si TFT active matrix Synchronization Horizontal 30 81 kHz Vertical 56 75 Hz Display Color 16 194 277 Colors Resolution Optimum resolution 1280 x 1024 60 Hz Maximum resolution 1280 x 1024 75 Hz Input Signal Terminated RGB Analog 0 7Vp p Positive at 75 ohms Separate H V sync Composite sync SOG TTL level positive or negative Maximum Pixel Clock 140 MHz Power
18. start the program ADAL ALAS AAA ALIADA NG Magictune execution icon may not appear depending on specification of computer OP system or monitor If that happens press F5 Key FERERBERETESTBSSPBSTPBPEBEBETTPBERERSERBETSPERSSSPBPBPBERETETBT TETPTBEBSESGSRSNEPRPSTEBPBEBEBESERBSSESSBEBERSEBRETRSBTBTPRTEBEBRBESEBSERTETPRSBRPBPBRRESGESNERTBESHNE 11 The following window appears if the installation is successful 12 The following error message indicates that the system is using a video card that is not supported by MagicTune MagicTune This version of MagicTune doesn t support the attached display Please try installing newer version of the graphics c a driver CLEE TETE EE TETE EG GNG NG EE EE AA AGA SPE CECT SSSA STE NET EGG AGE GNG NG GENE EGG NG GG AGA GG GG EG GG E cio Installation Problems The installation of MagicTune 2 5 can be affected by such factors as the video card motherboard and the network environment See Troubleshooting if you have trouble during installation Pb System Requirements OS Windows 98 SE Windows Me Windows NT Windows 2000 Windows XP Home Edition Windows XP Professional Hardware e 32MB Memory above e 25MB Hard disk space above For more information visit the MagicTune website Specifications subject to change without notice MagicTune is a trademark of SAMSUNG ELECTRONICS CO Inc Windows is a registered trademark of Microsoft Corp Other trademarks ar
19. such as text and graphics 4 Entertain High Brightness For watching motion pictures such as a DVD or VCD gt gt Click here to see an animation clip When OSD is not on the screen Push the button to adjust brightness Adjust items in the menu Activates a highlighted menu item Use this button for auto adjustment Use this button for turn the monitor on and off This light glows green during normal operation and blinks green once as the monitor saves your adjustments Y See PowerSaver described in the manual for further information regarding power saving E N functions For energy conservation turn your monitor OFF when it is not needed or when leaving it unattended for long periods Unpacking Front Rear l Rear The configuration at the back of the monitor may vary from product to product 1 Power port Connect the power cord for your monitor to the power port on the back of the monitor 2 D sub 15 pin port Connect the signal cable to the 15 pin D sub connector on the back of your monitor C T See Connecting the Monitor for further information regarding cable connections SyncMaster 912T everyone s invite m Safety Instructions ida Setup m Adjusting Your Monitor Troubleshooting Specifications E Information Unpacking Front Rear Please make sure the following items are included with your monitor If any items are missing contact your dealer Unpack
20. the power off for 2 hours after 12 hours in use e Use a Screen saver if possible Screen saver in one color or a moving image is recommended e Set the Monitor to power off with the PC Display Properties Power Scheme 2 Suggestions for specific applications Ex Airports Transit Stations Stock Markets Banks and Controlling Systems We recommend that you follow set up of your display system program as below Display Information together with Logo or Moving image cycle Ex Cycle Display Information for 1 hour followed by a Display Logo or moving image for 1 minute Change the Color Information periodically Use 2 different colors Ex Rotate the Color Information with 2 colors every 30 minutes Type 1 Type 1 FLGHT TIME FLGHT TIME 02348 20 30 da gt Bevel 20 30 UA102 21 10 UA102 21 10 Avoid using a combination of characters and background color with large difference in luminance Avoid using Grey colors which can cause Image retention easily e Avoid Colors with big difference in luminance Black amp White Grey Ex SYSTEM 245 e Recommended settings Bright colors with little difference in luminance Change the characters color and background color every 30 minutes Ex SYSTEM 245 SYSTEM 245 STATUS OK STATUS OK Every 30 minutes change the characters with movement Ex AA ce a TAPAT KA1710 12 00 KA1710 12 00 UA0110 13 30 PATI WEO 1180110 12 2N AA0002 14 00 FA7777 14 15
21. visual ergonomics and image quality in order to improve the working environment for the user and to reduce sight and strain problems Important parameters are luminance contrast resolution reflectance colour rendition and image stability Energy e Energy saving mode after a certain time beneficial both for the user and the environment e Electrical safety Emissions e Electromagnetic fields e Noise emissions Ecology e The product must be prepared for recycling and the manufacturer must have a certified environmental management system such as EMAS or ISO 14 000 e Restrictions on o chlorinated and brominated flame retardants and polymers o heavy metals such as cadmium mercury and lead The requirements included in this label have been developed by TCO Development in cooperation with scientists experts users as well as manufacturers all over the world Since the end of the 1980s TCO has been involved in influencing the development of IT equipment in a more user friendly direction Our labelling system started with displays in 1992 and is now requested by users and IT manufacturers all over the world For more information Please visit www tcodevelopment com TCO 03 Recycling Information TCO 03 applied model only For recycling information for TCO 03 certified monitors for the residents in the following countries please contact the company corresponding to your region of residence For those who reside in other countries p
22. you to adjust it for your unique setting Unfortunately the manual controls available to tune the image often prove to be challenging Proper adjustment tuning requires an easy to use program that goes through a step by step process to obtain the best overall picture quality In most cases even simple adjustments to Brightness or Contrast require navigation of the multi level on screen display OSD menus that are not easy to understand Furthermore there is no feedback to assist in correctly setting the controls of the monitor MagicTune is a software utility that guides you through the tuning process with easy to understand instructions and back ground patterns designed for each monitor control The display settings for each user can be saved providing an easy way to select display characteristics in a multi user environment or having a single user have multiple defined presets based on content and ambient lighting HUGE AAA LI poy 3 Basic Functionality MagicTune is a software utility that allows monitor adjustment and color tuning using the Display Data Channel Command Interface DDC CI protocol All adjustments to the display are controlled via software to eliminate the need to use the monitor on screen display OSD MagicTune supports Windows 98SE Me 2000 NT XP Home and XP Professional MagicTune allows for quick accurate tuning of the display with the ability to easily save and use monitor configurations that are best suited
23. 175 25 175 28 322 30 240 57 284 100 00 31 500 31 500 36 000 40 000 49 500 50 000 65 000 75 000 78 750 108 00 108 00 135 00 The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle and the inverse number of the Horizontal Cycle is called Horizontal Frequency Unit kHz Vertical Frequency Like a fluorescent lamp the screen has to repeat the same image many times per second to display an image to the user The frequency of this repetition is called Vertical Frequency or Refresh Rate Unit Hz SyncMaster 912T SAMSUN everyone s B Safety Instructions B Introduction E Setup E Adjusting Your Monitor B Information Troubleshooting General PowerSaver Preset Timing Modes General General Model Name SyncMaster 912T LCD Panel Size 19 Diagonal Display area 376 32 H x 301 056 V Pixel Pitch 0 294mm H x 0 294mm V Type a si TFT active matrix Synchronization Horizontal 30 81 kHz Vertical 56 75 Hz Display Color 16 777 219 Colors Resolution Optimum resolution 1280 x 1024 60 Hz Maximum resolution 1280 x 1024 75 Hz Input Signal Terminated RGB Analog DVI Digital Visual Interface Compliant Digital RGB 0 7Vp p Positive at 75 ohms Separate H V sync Composite sync SOG TTL level positive or negative Maximum Pixel Clock 140 MHz Power Supply AC 100 240 VAC 10 60 50 Hz 3Hz Signal Cab
24. 6 Wait until the Uninstall Complete dialog box appears Visit the MagicTune website for technical support for MagicTune FAQs questions and answers and software upgrades Specifications subject to change without notice MagicTune is a trademark of SAMSUNG ELEC TRC NICS CO Inc Windows is a registered trademark of Microsoft Corp Other trademarks are property of their respective holders MagicTune HELP Color Calibration Overview Installation OSD Mode Uninstall Troubleshooting Troubleshooting e MagicTune may not work in case monitor is replaced or driver of graphic card is updated while MagicTune is operating If so please restart the system Check when MagicTune does not function properly MagicTune feature is found only on PC VGA with Window OS that supports Plug and Play To check whether your PC is available for MagicTune feature follow the steps below When Windows is XP Control Panel gt Performance and Maintenance gt System Hardware gt Device Manager gt Monitors gt After deleting Plug and Play monitor find Plug and Play monitor by searching new Hardware e Visit the MagicTune website for technical support for MagicTune FAQs questions and answers and software upgrades lago Taras Specifications subject to change without notice MagicTune is a trademark of SAMSUNG ELECTRONICS CO Inc Windows is a registered trademark of Microsoft Corp Other tra
25. D Tel 0208 391 0168 Fax 0208 397 9949 lt European Service Center amp National Service gt Stafford Park 12 Telford Shropshire TF3 3BJ Tel 0870 242 0303 Fax 01952 292 033 http samsungservice co uk 9 U S A Samsung Electronics America Service Division 400 Valley Road Suite 201 Mount Arlington NJ 07856 1 800 SAMSUNG 1 800 726 7864 http samsungusa com monitor Service Terms For Better Display Authority Regulatory Image Retention Free Terms 2 Dot Pitch The image on a monitor is composed of red green and blue dots The closer the dots the higher the resolution The distance between two dots of the same color is called the Dot Pitch Unit mm Vertical Frequency The screen must be redrawn several times per second in order to create and display an image for the user The frequency of this repetition per second is called Vertical Frequency or Refresh Rate Unit Hz Example If the same light repeats itself 60 times per second this is regarded as 60 Hz Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle The inverse number of the Horizontal Cycle is called Horizontal Frequency Unit kHz Interlace and Non Interlace Methods Showing the horizontal lines of the screen from the top to the bottom in order is called the Non Interlace method while showing odd lines and then even lines in turn
26. Supply AC 100 240 VAC 10 60 50 Hz 3Hz Signal Cable 15pin to 15pin D sub cable detachable Power Consumption Less than 38W Dimensions WxDxH Weight Simple Stand 416 6 x 60 2 x 349 4 mm Without Stand 416 6 x 215 2 x 424 6 mm with Basic Stand 5 6 kg Dimensions WxDxH Weight Pivot Stand 416 6 x 60 2 x 349 4 mm Without Stand 416 6 x 200 0 x 420 6 mm with Basic Stand 7 2 kg VESA Mounting Interface 100mm x 100mm for use with Specialty Arm Mounting hardware Environmental considerations Operating Temperature 50 F 104 F 10 C 40 C Humidity 10 80 non condensing Storage Temperature 4 F 113 F 20 C 45 C Humidity 5 95 non condensing Plug and Play Capability This monitor can be installed on any Plug amp Play compatible system Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings In most cases monitor installation will proceed automatically unless the user wishes to select alternate settings Dot Acceptable TFT LCD panel manufactured by using advanced semiconductor technology with precision of 1ppm one millionth above is used for this product But the pixels of RED GREEN BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen This is not from bad quality and you can use it without uneasiness e For example the number of TFT LCD sub pixels that is contained in this product
27. al Communications Commission It is available from the U S Government Printing Office Washington DC 20402 Stock Number 004 000 00345 4 The party responsible for product compliance SAMSUNG ELECTRONICS CO LTD America QA Lab of Samsung 3351 Michelson Drive Suite 290 Irvine CA92612 USA Tel 949 975 7310 Fax 949 922 8301 Warning User must use shielded signal interface cables to maintain FCC compliance for the product Provided with this monitor is a detachable power supply cord with IEC320 style terminations It may be suitable for connection to any UL Listed personal computer with similar configuration Before making the connection make sure the voltage rating of the computer convenience outlet is the same as the monitor and that the ampere rating of the computer convenience outlet is equal to or exceeds the monitor voltage rating For 120 Volt applications use only UL Listed detachable power cord with NEMA configuration 5 15P type parallel blades plug cap For 240 Volt applications use only UL Listed Detachable power supply cord with NEMA configuration 6 15P type tandem blades plug cap IC Compliance Notice This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations of ICES 003 Cet appareil Num rique de classe B respecte toutes les exigences du Reglemont NMB 03 sur les quipements produisant des interferences au Canada MPR II Compliance This monitor com
28. aster 915N po everyone s E Safety Instructions E Introduction Setup W Adjusting Your Monitor Troubleshooting B Information General PowerSaver Preset Timing Modes General General Model Name SyncMaster 915N LCD Panel Size 19 Diagonal Display area 376 32 H x 301 056 V Pixel Pitch 0 294mm H x 0 294mm V Type a si TFT active matrix Synchronization Horizontal 30 81 kHz Vertical 56 75 Hz Display Color 16 194 277 Colors Resolution Optimum resolution 1280 x 1024 60 Hz Maximum resolution 1280 x 1024 75 Hz Input Signal Terminated RGB Analog 0 7Vp p Positive at 75 ohms Separate H V sync Composite sync SOG TTL level positive or negative Maximum Pixel Clock 140 MHz Power Supply AC 100 240 VAC 10 60 50 Hz 3Hz Signal Cable 15pin to 15pin D sub cable detachable Power Consumption Less than 38W Dimensions WxDxH Weight 416 6 x 60 2 x 349 4 mm Without Stand 416 6 x 215 2 x 424 6 mm with Basic Stand 5 6 kg VESA Mounting Interface 100mm x 100mm for use with Specialty Arm Mounting hardware Environmental considerations Operating Temperature 50 F 104 F 10 C 40 C Humidity 10 80 non condensing Storage Temperature 4 F 113 F 20 C 45 C Humidity 5 95 non condensing Plug and Play Capability This monitor can be installed on any Plug amp Play compatible system Interaction of the monitor and computer systems will pr
29. ations E Information Unpacking Front Rear Please make sure the following items are included with your monitor If any items are missing contact your dealer Unpacking Bottom Manual e User s Guide Monitor Driver Natural Color software MagicTune software Warranty Card Quick Setup Guide Not available in all locations 2 Cable D Sub Cable Power Cord Unpacking Front Rear SAMSUNG Front 1 Menu button III 2 MagicBright button ta 3 Brightness button 4 2 3 Adjust buttons Y A 4 Enter button 5 Auto button 6 Power button 7 Power indicator Opens the OSD menu Also use to exit the OSD menu or return to the previous menu MagicBright is a new feature providing optimum viewing environment depending on the contents of the image you are watching Currently four different modes are available Custom Text Internet and Entertain Each mode has its own pre configured brightness value You can easily select one of four settings by simply pressing MagicBright control buttons 1 Custom Although the values are carefully chosen by our engineers the pre configured values may not be comfortable to your eyes depending on your taste If this is the case adjust the Brightness and Contrast by using the OSD menu 2 Text Normal Brightness For documentations or works involving heavy text 3 Internet Medium Brightness For working with a mixture of images
30. ause any actions PORES AAA SSPE ESSERE SPSS EAG AE EES vpo 3 Picture Tab Definition Allows the user to adjust the screen settings to the desired values Brightness Contrast Resolution MagicBright Makes the entire screen brighter or darker The detailed data of the images in the dark Brightness areas can be lost if the brightness is not adjusted to the proper level Adjust the brightness for best viewing conditions Adjusts the difference in brightness between the bright and dark areas on screen Contrast Determines the crispness of the images Resolution m Lists all display resolutions supported by the program MagicBright is a new feature providing the optimum viewing environment depending on the contents of the image you are watching Currently four different modes are available Text Internet Entertain and Custom Each mode has its own pre configured brightness value You can easily select one of four settings by simply pressing the MagicBright control button MagicBright Text For documentations or works involving heavy text Internet For working with a mixture of images such as text and graphics Entertain For watching motion pictures such as a DVD or VCD Custom Although the values are carefully chosen by our engineers the pre configured values may not be comfortable to your eyes depending on your taste If this is the case adjust the Brightness and Contrast by using the OSD m
31. ay go blank while the power LED is on Refer to the video card manual and adjust the screen as follows Table 1 Preset Timing Modes Horizontal Vertical Frequency Pixel Clock Display Mode Sync Polarity Frequency MHz H V IBM 640 x 350 IBM 640 x 480 IBM 720 x 400 MAC 640 x 480 MAC 832 x 624 MAC 1152 x 870 VESA 640 x 480 VESA 640 x 480 VESA 800 x 600 VESA 800 x 600 VESA 800 x 600 VESA 800 x 600 VESA 1024 x 768 VESA 1024 x 768 VESA 1024 x 768 VESA 1152 x 864 VESA 1280 x 1024 VESA 1280 x 1024 kHz 31 469 31 469 31 469 35 000 49 726 68 681 37 500 37 861 35 156 37 879 46 875 48 077 48 363 56 476 60 023 67 500 63 981 79 976 Hz 70 086 59 940 70 087 66 667 74 551 75 062 75 000 72 809 56 250 60 317 75 000 72 188 60 004 70 069 75 029 75 000 60 020 75 025 Horizontal Frequency 25 175 25 175 28 322 30 240 57 284 100 00 31 500 31 500 36 000 40 000 49 500 50 000 65 000 75 000 78 750 108 00 108 00 135 00 The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle and the inverse number of the Horizontal Cycle is called Horizontal Frequency Unit kHz Vertical Frequency Like a fluorescent lamp the screen has to repeat the same image many times per second to display an image to the user The frequency of this repetition is called Vertical Frequency or Refresh Rate Unit Hz SyncM
32. compliant mounting interface pad Simple stand Pivot stand A Monitor B Mounting interface pad Turn off your monitor and unplug its power cord Lay the LCD monitor face down on a flat surface with a cushion beneath it to protect the screen Remove four screws and then remove the Stand from the LCD monitor Align the Mounting Interface Pad with the holes in the Rear Cover Mounting Pad and secure it with four screws that came with the arm type base wall mount hanger or other base SyncMaster 912T SAMSUN A A ra everyone s invi W Specifications E Information Connecting the Monitor Using the Stand Installing the Monitor Driver Installing the Monitor Driver Natural Color i Automatic Manual New Model Macintosh Old Model Macintosh Connect the power cord for your monitor to the power port on the back of the monitor Plug the power cord for the monitor into a nearby outlet Using the D sub Analog connector on the video card Connect the signal cable to the 15 pin D sub connector on the back of your monitor Connected to a Macintosh Connect the monitor to the Macintosh computer using the D SUB connection cable In the case of an old model Macintosh you need to connect the monitor using a special Mac adapter Turn on your computer and monitor If your monitor displays an image installation is complete SyncMaster 912T Connecting the Monitor Usin
33. cubleshoc Color Management 7 p Hore Ep 7 E Fhag aridi Fr ignitor Phag and Ple Monitor Davisa bpo ETET biombo zetlingr i Marulashwer Gtardard monitor types Screen mish rate Locadior on 20 Prophet IH 60 Henz 3 o Device denas This elavana in bing popad C Hide rodas that this mora Cannot displau Clang thie check box allows you to select display modes Ihat this IF you ane hasang problems path the device click Troubleshoot ta rm peer freien s EE a Wak pete et wa i Lom iha device eoruin Welcome to the Hardware Update Wizard Tris wizard helpi you instal actas for Plug trad Play Morato 5 1 2001 0 WM pour hagdanan come milh an mksEstion CD a Hope disk imet i nae To mr ads ae Ls abes dein To updais thee ceiver for his devica What do pou vane the wid In de CO Intball the beng autoretically Recommended Rive Hoxie lal aller the dives rol 5 mta hon a bet a pait locaton Eh back to Ue previously ivar ici Het lo contras 6 Hardware Update Wizard Hardware Update Wizard Plese choose you znanch and installation options feleo the devine dive pou want b install es this haideane C Sach les the best divei in these location la Ina acana Can then chek Hasi If you vaL EE en eL E palta aed errar able red T has bett dree bound kal be cad Seach remonabds pedia Boppy COPADA Irzckades thes kesion m the peach Choose thie opti
34. d shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing performance or use of this material Samsung is the registered trademark of Samsung Electronics Co Ltd Microsoft Windows and Windows NT are registered trademarks of Microsoft Corporation VESA DPMS and DDC are registered trademarks of Video Electronics Standard Association the ENERGY STAR name and logo are registered trademarks of the U S Environmental Protection Agency EPA As an ENERGY STAR Partner Samsung Electronics Co Ltd has determined that this product meets the ENERGY STAR guidelines for energy efficiency All other product names mentioned herein may be the trademarks or registered trademarks of their respective owners FCC Information IC Compliance Notice MPR Il Compliance European Notice Europe only PCT Notice VCCI TCO 95 Ecological requirements for personal computers TCO 95 applied model only TCO 99 Ecological requirements for personal computers TCO 99 applied model only TCO 03 Ecological requirements for personal computers TCO 03 applied model only TCO 03 Recycling Information TCO 03 applied model only Medical Requirement Mercury Statement LCD Monitor LCD TV DLP Projection TV Projector for USA only FCC Information User Instructions The Federal Communications Commission Radio Frequency Interference Statement includes the following warning Note This equi
35. demarks are property of their respective holders mm SyncMaster 913N 915N ELECTRONICS E i JEAN J L Fi gt B EB 3 ina me a every one s inv tear B Safety Instructions E Introduction 8 Setup E Adjusting Your Monitor EEE W Specifications E Information Check List Q amp A Self Test Feature Check Y X Before calling for service check the information in this section to see if you can remedy any Pagi problems yourself If you do need assistance please call the phone number on the Information section or contact your dealer Symptom Check List Solutions No images on the Is the power cord connected Check the power cord connection screen cannot turn properly and supply on the monitor Can you see Check Signal Check the signal cable connection Cable on the screen If the power is on reboot the If the initial screen the login screen computer to see the initial screen appears boot the computer in the the login screen which can be applicable mode the safe mode for seen Windows ME XP 2000 and then change the frequency of the video card Refer to the Preset Timing Modes Note If the initial screen the login screen does not appear contact the Service Center or your dealer Can you see Not Optimum You can see this message when the Mode Recommanded Mode signal from the video card exceeds 1280 x 1024 60Hz on the screen the maximum resolution and frequency that the monitor ca
36. e property of their respective holders Magiclune HELP TI Col Overview Installation OSD Mode m install T leshooti Calibration Uninstall Troubleshooting EE EE EE TETE ET EE EE EE LET SPRPSSSSESESESSSS SESS SSE ESSEC ESSERE SS EGG GAGA EEEEEG EGG EGG NG E T E T MagicTune allows for quick accurate tuning of the display with the ability to easily save and use monitor configurations that are best suited for you HAHAHAH mre e OSD mode may appear inconsistent with the explanation in guidance book depending on specification of each monitor e When Pivot is functioning part of Magictune Program may not operate normally TETE AKA PSS AKA KAKA KAKA KA ERE EE DEEP NAN BE NENE ONE HA PENE PATABA NENENG A FE FEED EDNE SPER PRPS SPSS SE NE OSD Mode Magiclune Picture Brightness The OSD mode makes the adjustment of settings on all monitors easy When selected each tab on top of the control window displays the general descriptions of the sub menu items for adjustment When selected each tab displays a list of menus For quick adjustment of the monitor settings the OSD mode allows easy and convenient access to all tabs and sub menu items 3 Button Tab Definition OK Applies any changes made and exits MagicTune Reset Restores the display settings to the factory settings Cancel Exits MagicTune without applying the changes made If you have not made any changes in the control window clicking Cancel does not c
37. e range of issues environment ergonomics usability emission of electrical and magnetic fields energy consumption and electrical and fire safety The environmental demands concern among other things restrictions on the presence and use of heavy metals brominated and chlorinated flame retardants CFCs freons and chlorinated solvents The product must be prepared for recycling and the manufacturer is obliged to have an environmental plan which must be adhered to in each country where the company conducts its operations policy The energy requirements include a demand that the monitor after a certain period of inactivity shall reduce its power consumption to a lower level in one or more stages The length of time to reactivate the monitor shall be reasonable for the user Labelled products must meet strict environmental demands for example in respect of the reduction of electric and magnetic fields along with physical and visual ergonomics and good usability TCO Development Unit 1996 11 29 On the page this folder you will find a brief summary of the environmental requirements met by this product The complere environmental criteria document may be ordered from TCO Development Unit S 11494 Stockholm Sweden Fax 46 8 782 92 07 E mail Internet development tco se Current information regarding TCO 95 approved and labelled products may also be obtained via the Internet using the address http www tco info com TCO 95 is a co
38. eature that allows you to check whether your monitor is functioning properly Self Test Feature Check 1 Turn off both your computer and the monitor 2 Unplug the video cable from the back of the computer 3 Turn on the monitor If the monitor is functioning properly you will see a box in the illustration below Check Signal Cable This box appears during normal operation if the video cable becomes disconnected or damaged 4 Turn off your monitor and reconnect the video cable then turn on both your computer and the monitor If your monitor screen remains blank after using the previous procedure check your video controller and computer system your monitor is functioning properly Warning Messages If there is something wrong with the input signal a message appears on the screen or the screen goes blank although the power indicator LED is still on The message may indicate that the monitor is out of scan range or that you need to check the signal cable Not Optimum Mode Recommended Mode 1280 x 1024 60Hz Environment The location and the position of the monitor may influence the quality and other features of the monitor 1 if there are any sub woofer speakers near the monitor unplug and relocate the woofer to another room 2 Remove all electronic devices such as radios fans clocks and telephones that are within 3 feet one meter of the monitor Useful Tips e A monitor recreates visual signals
39. ect the Monitor tab Click the Change button in the Monitor Type area Choose Specify the location of the driver Choose Display a list of all the driver in a specific location then click Next button Click the Have Disk button Specify A D driver then click OK button Select Show all devices and choose the monitor that corresponds to the one you connected to your computer and click OK Continue choosing Close button and OK button until you close the Display Properties dialogue box CO pO UPON KHA Microsoft Windows NT Operating System Click Start Settings Control Panel and then double click Display icon 2 In Display Registration Information window click Settings Tab and then click All Display Modes 3 Select a mode that you wish to use Resolution Number of colors and Vertical frequency and then click OK 4 Click Apply button if you see the screen working normally after clicking Test If the screen is not normal change to a different mode lower mode of resolution colors or frequency V If there is no Mode at All Display Modes select the level of resolution and vertical ER frequency by referring to the Preset Timing Modes in the user guide 2 Linux Operating System To execute X Window you need to make the X86Config file which is a type of system setting file Press Enter at the first and the second screen after executing the X86Config file The third scree
40. ed The monitor is in PowerSaver mode press a key on the keyboard to activate the monitor and restore the image on the screen Check the signal cable connection Make sure the video card is fully inserted in it s slot Reboot the computer Set the video card by referring to the video card manual Adjust screen image position and size using the OSD Adjust the resolution and frequency at the video card Refer to the Preset Timing Modes The screen can be unbalanced due to the cycle of the video card signals Readjust Position by referring to the OSD Have you adjusted the resolution or frequency on the monitor Is the frequency properly adjusted when checking the Display Timing on the menu Have the Windows colors been set properly Has the video card been set properly Have you installed the monitor driver See the video card manual to see if the Plug amp Play VESA DDC function can be supported Have you changed your PC or video graphic card Adjust the resolution and frequency of the video card Refer to the Preset Timing Modes Adjust the frequency properly by referring to the video card manual and the Preset Timing Modes The maximum frequency per resolution may differ from product to product Windows ME 2000 XP Set the colors properly at the Control Panel Display Settings Set the video card by referring to the video card manual Install the monitor driver accordi
41. el 08 25 08 65 65 Fax 01 48 63 06 38 http www samsungservices com 2 GERMANY TELEPLAN Rhein Main GmbH Feldstr 16 64331 Weiterstadt T 06151 957 1306 F 06151 957 1732 EURO 0 12 Min http www samsung de 2 HUNGARY Samsung Electronics Magyar Rt 1039 Budapest Lehel u 15 17 Tel 36 1 453 1100 Fax 36 1 453 1101 http www samsung hu 2 ITALY Samsung Electronics Italia S p a Via C Donat Cattin 5 20063 Cernusco s Naviglio MI Servizio Clienti 199 153 153 http www samsung italia com M XICO SAMSUNG ELECTRONICS MEXICO S A de C V Via Lopez Portillo No 6 Col San Fco Chilpan Tultitlan Estado de Mexico C P 54940 Tel 01 55 5747 5100 01 800 726 7864 Fax 01 55 5747 5202 01 800 849 1743 RFC SEM950215598 http www samsung com mx IMPORTADO POR SAMSUNG ELECTRONICS MEXICO S A de C V Via Lopez Portillo No 6 Col San Fco Chilpan Tultitlan Estado de M xico C P 54940 Tel 01 55 5747 5100 01 800 726 7864 EXPORTADO POR Samsung Electronics CO LTD 416 Mae tan 3dong Yeongtong gu Suwon City Gyeonggi do Korea NETHERLANDS BELGIUM LUXEMBOURG Samsung Electronics Benelux B V Fleminglaan 12 2289 CP Rijiswijk NEDERLANDS Service and informatielijn Belgium 0800 95214 http www samsung be Netherlands 0800 2295214 hitp www samsung nl PANAMA Samsung Electronics Latinoamerica Z L S A Calle 50 Edificio Plaza Credicorp Planta Baja Panama Tel 507 210 1122
42. en The Swedish Society for Nature Conservation These demands impose restrictions on the presence and use of heavy metals brominated and chlorinated flame retardants CFCs freons and chlorinated solvents among other things The product must be prepared for recycling and the manufacturer is obliged to have an environmental policy which must be adhered to in each country where the company implements its operational policy The energy requirements include a demand that the computer and or display after a certain period of inactivity shall reduce its power consumption to a lower level in one or more stages The length of time to reactivate the computer shall be reasonable for the user Below you will find a brief summary of the environmental requirements met by this product The complete environmental criteria document may be ordered from TCO Development SE 114 94 Stockholm Sweden Fax 46 8 782 92 07 Email Internet development tco se Current information regarding TCO 99 approved and labelled products may also be obtained via the Internet using the address http www tco info com Environmental requirements Flame retardants Flame retardants are present in printed circuit boards cables wires casings and housings Their purpose is to prevent or at least to delay the spread of fire Up to 30 of the plastic ina computer casing can consist of flame retardant substances Most flame retardants contain bromine or chloride and those
43. enu a pH ES ERE AAA AA AAA AAA dicte 3 Color Tab Definition Adjusts the warmth of the monitor background or image color e Color Tone Color Control Calibration The tone of the color can be changed Color Tone e Warm Normal Cool e Custom Adjusts of the monitor image color Color Control You can change the monitor color to your desired color e R G B The process through which the colors of your choice are optimized and maintained You F will find MagicTune extremely useful if you are one of those who wish to view images with Calibration their full details accurately reproduced including web images and ones produced by a digital camera or scanner SRPPEPEPESPESSSS ER FE ES SPSS SS ES PE SSSR SS SSS ESSE SARS SS SSS SPSS SSS SS SS SSS NG FAFA HEN NENE DFA TERE NE NENE SSP HSS TETE TEE de Image Tab Definition Adjusts the Fine Coarse and Position values Magic LIME Image Setup Fine ET 1 Course image Setup Position e Fine Removes noise such as horizontal stripes If the noise persists even after Fine tuning repeat it after adjusting the frequency clock speed Image Setup e Coarse Removes noise such as vertical stripes Coarse adjustment may move the screen image area You may relocate it to the center using the Horizontal Control menu e Auto Setup Auto adjustment allows the monitor to self adjust to the incoming video signal The values of fine coarse and posi
44. ess Feature When OSD is not on the screen Q Q Push the button to adjust brightness Contrast Adjust the Contrast 1 Q Color 2 Menu Description Play Stop The tone of the color can be changed and one of four VOLO ONE modes can be selected Cool normal Warm and Custom 2 Q Follow these steps to adjust individual R G B color CEOIOFSONNO balance Q Q Gamma Select one of three pre defined gammas Q Q Image Menu Description Play Stop Removes noise such as vertical stripes Coarse Coarse adjustment may move the screen image area You may Q Q relocate it to the center using the Horizontal Control menu Removes noise such as horizontal stripes If the noise Fine persists even after Fine tuning repeat it after adjusting the Q Q frequency clock speed Sharpness Follow these instuction to change the clearance of image Q Q H Position Follow these instructions to change the horizontal position Q Q of the monitor s entire display Follow these instructions to change the vertical position of Q Q the monitor s entire display V Position osp 3 Description Play Stop Follow these steps to change the language used in the menu You can choose one of seven languages English German Spanish French Italian Swedish Russian Q Q Note The language chosen affects only the language of the OSD It has no effect on any software running on the computer Language You can change the hor
45. f RED GREEN BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen This is not from bad quality and you can use it without uneasiness o For example the number of TFT LCD sub pixels that is contained in this product are 3 932 160 3 When you clean the monitor and the panel outside please apply the recommended small amount of cleaner by using soft and dry cloth and polish it Let LCD area not to be forced but to be scrubbed out softly If excessive force is applied you can have a stain on it 4 If you are not satisfied with the quality of picture you can get better quality of picture by executing auto adjustment function in display screen that is appeared as window termination button is pressed If there s still noise after automatic adjustment use FINE COARSE adjustment function 5 If you view a fixed screen for an extended period of time residual image or blurriness may appear Change the mode to energy save or set a screensaver to moving picture when you need to be away from the monitor for an extended period of time Service Terms For Better Display Authority Regulatory Image Retention Free Authority Information in this document is subject to change without notice 2005 Samsung Electronics Co Ltd All rights reserved Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co Ltd is strictly forbidden Samsung Electronics Co Lt
46. fine coarse and position are adjusted automatically User Control Buttons Direct Functions OSD Functions Moca MagicTune AUTO Description When the AUTO button is pressed the Auto Adjustment screen appears as shown in the animated screen on the center Auto adjustment allows the monitor to self adjust to the incoming video signal The values of fine coarse and position are adjusted automatically To make the automatic adjustment function sharper execute the AUTO function while the AUTO PATTERN is on e f Auto Adjustment does not work properly press Auto button again to adjust picture with more accuracy e lf you change resolution in the control panel Auto function will be executed automatically MagicBright Menu MagicBright Description Then push the MagicBright button again to circle through available preconfigured modes four different modes Custom T ext Internet Entertain Brightness Menu Description Brightness Adjust Brightness User Control Buttons Direct Functions OSD Functions star MagicTune 1 Picture Ml Brightness 2 Color BI Color Tone Color Control 3 Image I coarse Fine Sharpness HPosion _ V Positon 08D E language HPosiion v Postion Transparency Display Time 5 Setup ME Image Reset Color Reset 6 Information O Picture 15 Menu Description Play Stop Adjust the Brightness Brightness Direct Acc
47. g the Stand Installing the Monitor Driver Installing the Monitor Driver Natural Color Automatic Manual Pivot Stand A Stand Stopper 2 Attaching a base This monitor accepts a 100 mm x 100 mm VESA compliant mounting interface pad Pivot stand A Monitor B Mounting interface pad Turn off your monitor and unplug its power cord 2 Lay the LCD monitor face down on a flat surface with a cushion beneath it to protect the Screen Remove four screws and then remove the Stand from the LCD monitor Align the Mounting Interface Pad with the holes in the Rear Cover Mounting Pad and secure it with four screws that came with the arm type base wall mount hanger or other base po Connecting the Monitor Using the Stand Installing the Monitor Driver Installing the Monitor Driver Natural Color Automatic Manual Y When prompted by the operating system for the monitor driver insert the CD ROM Da Lt u u u m included with this monitor Driver installation is slightly different from one operating system to another Follow the directions appropriate for the operating system you have Prepare a blank disk and download the driver program file at the Internet web site shown here Internet web site http www samsung com Worldwide http www samsungusa com monitor USA http www sec co kr monitor Korea http www samsungmonitor com cn China 2 Windows ME 1 Insert CD
48. h German Spanish French Italian Swedish Russian Q Q Note The language chosen affects only the language of the OSD It has no effect on any software running on the computer Language You can change the horizontal position where the OSD Q Q menu appears on your monitor H Position is You can change the vertical position where the OSD menu Vacs mon appears on your monitor 2 Q Transparency Change the transparency of the background of the OSD Q Q The menu will be automatically turned if no adjustments are made for a certain time period O Q You can set the amount of time the menu will wait before it is turned off Display Time O Setup ME Menu Description Play Stop Select Auto Source for the monitor to automatically select Q Q Auto Source the signal source Image Reset Image parameters are replaced with the factory default Q Q values Color parameters are replaced with the factory default Q Q lor R Color Reset vales Information 4 SOURCE Menu Description Information Shows a video source display mode on the OSD screen Magiclune HELP JI Overview Installation OSD Mode oa install T leshooti Calibration Uninstall Troubleshooting Overview 2 What is MagicTune Monitor performance can vary due to the graphics card host computer lighting conditions and other environmental factors In order to get the best image on a monitor requires
49. ing Monitor amp Pivot stand Manual Warranty Card token Do Quick Setup Guide Not available in all N I Col f locations atural Color software MagicTune software 2 Cable D Sub Cable Power Cord DVI Cable Unpacking Front Rear SAMSUNG Front 1 Menu button M 2 MagicBright button 2 14 3 Brightness button 4 2 3 Adjust buttons Y A Enter button Source button Opens the OSD menu Also use to exit the OSD menu or return to the previous menu MagicBright is a new feature providing optimum viewing environment depending on the contents of the image you are watching Currently four different modes are available Custom Text Internet and Entertain Each mode has its own pre configured brightness value You can easily select one of four settings by simply pressing MagicBright control buttons 1 Custom Although the values are carefully chosen by our engineers the pre configured values may not be comfortable to your eyes depending on your taste If this is the case adjust the Brightness and Contrast by using the OSD menu 2 Text Normal Brightness For documentations or works involving heavy text 3 Internet Medium Brightness For working with a mixture of images such as text and graphics 4 Entertain High Brightness For watching motion pictures such as a DVD or VCD gt gt Click here to see an animation clip When OSD is not on the screen Push the button to adjust brightness Ad
50. into the CD ROM drive 2 Click Windows ME Driver 3 Choose your monitor model in the model list then click the OK button Samsung Monitor Setun for Windows 1E3895 Pick the display adapter which you want to install the monitor 53 Inc savaged Pick the monitor which you want to install SyncMaster 7 3DEXI753DEX SyncMaster 753DF s703DF s 7 B3DF S MagicSyncMaster SyncMaster F 55DF x 4 Click the Install button in the Warning window Warming Select the monitor name that exactly matches the name printed on the front of your monitor or on the back label If you select the wrong monitor restart Windows in the Safe Mode and use this CD ROM again to select the correct monitor tea Cha 5 Monitor driver installation is completed 2 Windows XP 2000 1 Insert CD into the CD ROM drive 2 Click Windows XP 2000 Driver 3 Choose your monitor model in the model list then click the OK button camoung donor Gotup for Windows A al Pick thee diipla baga or ahh yess aanak ba iret tee rr bo TODA Cor PAKA OO CE mi intake rra boa E Waster 17157 1755 1705 Magic syncMaater Cx i Pick cham meritor which You eat TO etal PT aa TA PUTA AA TG AA AA O LS LOA e Ella aa IBAT 1 App ee Si adita 415 LER DRC Sinclar 1T TIME vrichtaster CELOO4 Ubo abad ATIS ore ta Mac myra acter CE FOME bi SPUR Lr tem a SyncMaster 171T 175T 170T Magica vrichMarter XI175BDU Sr Maila 171T 12371
51. is called the Interlace method The Non Interlace method is used for the majority of monitors to ensure a clear image The Interlace method is the same as that used in TVs 2 Plug Play This is a function that provides the best quality screen for the user by allowing the computer and the monitor to exchange information automatically This monitor follows the international standard VESA DDC for the Plug amp Play function 2 Resolution The number of horizontal and vertical dots used to compose the screen image is called resolution This number shows the accuracy of the display High resolution is good for performing multiple tasks as more image information can be shown on the screen Example If the resolution is 1280 x 1024 this means the screen is composed of 1280 horizontal dots horizontal resolution and 1024 vertical lines vertical resolution Service Terms For Better Display Authority Regulatory Image Retention Free For Better Display 1 Adjust computer resolution and screen injection rate refresh rate oncomputer as described below to enjoy the best quality of picture You can have an uneven quality of picture in the screen if the best quality of picture is not provided in TFT LCD o Resolution 1280 x 1024 o Vertical frequency refresh rate 60 Hz 2 TFT LCD panel manufactured by using advanced semiconductor technology with precision of 1ppm one millionth above is used for this product But the pixels o
52. itches Mercury damages the nervous system and is toxic in high doses e CO 95 requirement states that batteries may not contain more than 25 ppm parts per million of mercury It also demands that no mercury is present in any of the electrical or electronics components concerned with the display unit CFCs freons CFCs freons are sometimes used for washing printed circuit boards and in the manufacturing of expanded foam for packaging CFCs break down ozone and thereby damage the ozone layer in the stratosphere causing increased reception on Earth of ultraviolet light with consequent increased risks of skin cancer malignant melanoma e The relevant TCO 95 requirement Neither CFCs nor HCFCs may be used during the manufacturing of the product or its packaging TCO 99 Ecological requirements for personal computers TCO 99 applied model only Congratulations You have just purchased a TCO 99 approved and labelled product Your choice has provided you with a product developed for professional use Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products This product meets the requirements for the TCO 99 scheme which provides for an international environmental and quality labelling labelling of personal computers The labelling scheme was developed as a joint effort by the TCO The Swedish Confederation of Professional Employees
53. izontal position where the OSD FI menu appears on your monitor H Position g You can change the vertical position where the OSD menu A VSPasioh appears on your monitor 2 Q Transparency Change the transparency of the background of the OSD Q Q The menu will be automatically turned if no adjustments are made for a certain time period Q Q You can set the amount of time the menu will wait before it is turned off Display Time UP O Setup Bit Menu Description Play Stop Image parameters are replaced with the factory default values 2 Q Color parameters are replaced with the factory default values 2 Q Image Reset Color Reset Information M Menu Description Information Shows a video source display mode on the OSD screen SyncMaster 912T B Safety Instructions E Introduction E Setup numis Troubleshooting Specifications E Information User Control Buttons Direct Functions OSD Functions subay MagicTune 1 Use this button for open the on screen menu and exits from the menu screen or closes screen adjustment menu This buttons allows you to adjust items in the menu This buttons allows you to adjust items in the menu Press this button activates a highlighted menu item a gt w m Press to self adjust to the incoming PC signal The values of fine coarse and position are adjusted automatically User Control Buttons Direct Functions OSD Functions Moca MagicTune
54. just items in the menu Activates a highlighted menu item Push the Source then Selects the Video signal while the OSD is off When the Source button is pressed to change the input mode a message appears in the center of the screen displaying the current mode analog or digital input signal Note If you select the Digital mode you must connect your monitor to the graphic card s port using the DVI cable 5 Auto button Use this button for auto adjustment 6 Power button Use this button for turn the monitor on and off 7 Power indicator This light glows green during normal operation and blinks green once as the monitor saves your adjustments Y See PowerSaver described in the manual for further information regarding power saving En functions For energy conservation turn your monitor OFF when it is not needed or when leaving it unattended for long periods Unpacking Front Rear Rear PREV Ree NANA i Y EN LL ee eee PPE Pee T ER Lil GA a The configuration at the back of the monitor may vary from product to product 1 Power port Connect the power cord for your monitor to the power port on the back of the monitor 2 DVI port Connect the DVI Cable to the DVI Port on the back of your Monitor 3 D sub 15 pin port Connect the signal cable to the 15 pin D sub connector on the back of your monitor 4 Power on off Switch Use this button for turn the monitor on and off option v A See Connecting the Monit
55. le 15pin to 15pin D sub cable detachable DVI D to DVI D connector detachable Power Consumption Less than 38W Dimensions WxDxH Weight 416 6 x 60 2 x 349 4 mm Without Stand 416 6 x 200 0 x 420 6 mm with Basic Stand 7 2 kg VESA Mounting Interface 100mm x 100mm for use with Specialty Arm Mounting hardware Environmental considerations Operating Temperature 50 F 104 F 10 C 40 C Humidity 10 80 non condensing Storage Temperature 4 F 113 F 20 C 45 C Humidity 5 95 non condensing Plug and Play Capability This monitor can be installed on any Plug amp Play compatible system Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings In most cases monitor installation will proceed automatically unless the user wishes to select alternate settings Dot Acceptable TFT LCD panel manufactured by using advanced semiconductor technology with precision of 1ppm one millionth above is used for this product But the pixels of RED GREEN BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen This is not from bad quality and you can use it without uneasiness e For example the number of TFT LCD sub pixels that is contained in this product are 3 932 160 Note Design and specifications are subject to change without prior notice General PowerSaver Preset Timing Modes 9 PowerSaver This monitor has a
56. lease contact a nearest local Samsung dealer for recycling information for the products to be treated in environmentally acceptable way U S A Residents Only European Residents Only SWEDEN NORWAY GERMANY COMPANY Sid Waste Transfer amp fet kRETSEN _ Elektronikkretur AS Recycling Inc ears DOOR Max Plank Strasse ADDRESS 442 Frelinghuysen Ave 6454 Etterstad 0602 Oslo 42 Newark NJ 07114 Fyrstikkalln 3B 50858 Collogne Barnhusgatan 3 4 Germany tr ELEPHONE 973 565 0181 08 54521290 23060740 49 0 2234 9587 0 FAX Fax 973 565 9485 08 545 212 99 23 06 07 41 per i AIL nfo el kretsen se adm gjelektronikkretur no vfw info vfw ag de HOME http www bcua org Solid http www el PAGE Waste_Disposal htm kretsen se htip www elretur no Medical Requirement Classifications In accordance with UL 2601 1 IEC 60601 1 the product is cssified as Continuous duty Class equipment which is not protected against ingress of liquids The product is not suitable for use in the presence of a flammable anaesthetic mixture with air or with oxygen or nitrous oxide EMC This equipment has been tested and found to comply with the limits for medical devices to the IEC 601 1 2 1994 These limits are designed to provide reasonable protection against harmful interference in a typical medical installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instr
57. lor values As many as 5 values can be saved 2 How to apply the saved color values Press Multi User button on main screen to select and use one of the saved color values WEBEBSHBRRBSNGEFEBRGEHEBERBSHSGHEEBEBEBEGHSEBGEBGHEBSZEBSTEAM ERE EA AAA AAA IRALA dicia 2 Preview Press Preview button on the Color Calibration The above picture will be shown 1 Press View Calibrated button to see the calibration effect which you adjusted 2 Press View Uncalibrated button to see the original image Specifications subject to change without notice MagicTune is a trademark of SAMSUNG ELECTRONICS CO Inc Windows is a registered trademark of Microsoft Corp Other trademarks are property of their respective holders Magiclune HELP TI Overview Installation OSD Mode d Calibration Uninstall Troubleshooting Uninstall The MagicTune program can be removed only by using the Add or Remove Programs option of the Windows Control Panel Perform the following steps remove MagicTune 1 Go to Task Tray Start Settings and select Control Panel in the menu If the program runs on Windows XP go to Control Panel in the Start menu 2 Click the Add or Remove Programs icon in Control Panel 3 Inthe Add or Remove Programs screen scroll down to find MagicTune Click on it to highlight it 4 Click the Change Remove button to remove the program 5 Click Yes to begin the uninstall process
58. mm SyncMaster 912T ELECTRONICS ama r JE a ue i y naaa We i Seni ne NL L EN everyone s invited B Safety Instructions E Introduction 8 Setup E Adjusting Your Monitor EEE W Specifications E Information Check List Q amp A Self Test Feature Check Y X Before calling for service check the information in this section to see if you can remedy any Pagi problems yourself If you do need assistance please call the phone number on the Information section or contact your dealer Symptom Check List Solutions No images on the Is the power cord connected Check the power cord connection screen cannot turn properly and supply on the monitor Can you see Check Signal Connected using the D sub Cable on the screen cable Check the signal cable connection Connected using the DVI cable If you still see an error message on the screen when the monitor is connected properly check to see if the monitor status is set to analog Press Source button to have the monitor double check the input signal source If the power is on reboot the If the initial screen the login screen computer to see the initial screen appears boot the computer in the the login screen which can be applicable mode the safe mode for seen Windows ME XP 2000 and then change the frequency of the video card Refer to the Preset Timing Modes Note If the initial screen the login screen does not appear con
59. monitor driver is under certified MS logo and this installation doesn t damage your system The certified driver will be posted on Samsung Monitor homepage http www samsung com 9 Click the Close button then click OK button continually Hardware Update Wizard Completing the Hardware Update Wizard Tan ez did heat irc rit ling the 3 fterana Foi E A gees Gims Chick Frith lo diria ur varad TyncMartrr 17154 1 7557 170 Mapic5yncMarter TM ird 115 Synichlagtes 17154 1755 1705 Mag pr Pl sde C755 Dies Proiz ET LI Lu Diwa Pabo ce ia 120M Derived Wea icr T O 0 0 Digia G kgr Hol igi pigres Drem Ontos To nor dotado about the dram hoz L Ugdam Driver To update the deser for this device x ii the dosa hada aftor upang iho chron rol L Bo Back Driver back Lo Linas giari ibaia Crean Wi To uniri adi the Area bahea chose 10 Monitor driver installation is completed Plug and Play Monitor and Al Prophet HN iroporitmoe re Ih y GeForce SE Dores E nac Packs EM Color Conectien General Badapker Micros Trda Color hiana E ears Ep um Phas are Piles Mia ropertion j Sore GO oer 0 eph sam Fath Hi ees ga 1 Hike srodes Una ds errors Corra diodos Cie beg Hs A buia rr pated ls de das koa If Mas matt a pers maka Tha ans kaa es sut aah cele Aaa da e Pune Microsoft Windows 2000 Operating System La Al When you can see Digital Signature Not Found
60. n handle properly Adjust the maximum resolution and frequency that the monitor can handle properly If the display exceeds SXGA or 75Hz a Not Optimum Mode Recommanded Mode 1280 x 1024 60Hz message is displayed If the display exceeds 85Hz the display will work properly but the Not Optimum Mode Recommanded Mode 1280 x 1024 60Hz message appears for one minute and then disappears Please change to the recommended mode during this one minute period The screen shows strange colors or just black and white The screen suddenly has become unbalanced The screen is out of focus or OSD cannot be adjusted LED is blinking but no images on the screen There are only 16 colors shown on the screen The screen colors have changed after changing the video card There is a message that reads Unrecognized monitor Plug Play VESA DDC monitor found MagicTune doesn t work properly There is no image on the screen Is the power indicator on the monitor blinking at 1 second intervals Is the screen displaying only one color as if looking at the screen through a cellophane paper Have the screen colors become strange after running a program or due to a crash between applications Has the video card been set properly Have you changed the video card or the driver Have you adjusted the resolution or frequency to the monitor The message is displayed again if the system is reboot
61. n is for setting your mouse Set a mouse for your computer The next screen is for selecting a keyboard Set a Keyboard for your computer The next screen is for setting your monitor First of all set a horizontal frequency for your monitor You can enter the frequency directly Set a vertical frequency for your monitor You can enter the frequency directly Enter the model name of your monitor This information will not affect the actual execution of X Window 10 You have finished setting up your monitor Execute X Window after setting other requested hardware eo on pos O po Connecting the Monitor Using the Stand Installing the Monitor Driver Installing the Monitor Driver Natural Color Automatic Manual Natural Color Natural Color Software Program dia cUm Color Color Management System Monitor Adjustment ETE Natural Color Color Managementsystem One of the recent problems in using a computer is that the color of the images printed out by a printer or other images scanned by a scanner or a digital camera are not the same as those shown on the monitor The Natural Color S W is the very solution for this problem It is a color administration system developed by Samsung Electronics in association with Korea Electronics amp Telecommunications Research Institute ETRI This system is available only for Samsung monitors and makes the color of the images on the monitor the same a
62. ng to the Driver Installation Instructions Install the monitor driver according to the Driver Installation Instructions Download the latest program The program can be downloaded from the http www samsung com Check the following items if there is trouble with the monitor h Check if the power cord and the video cables are properly connected to the computer 2 Check if the computer beeps more than 3 times when booting If it does request an after service for the main board of the computer 3 If you installed a new video card or if you assembled the PC check if the installed the adapter video driver and the monitor driver 4 Check if the scanning ratio of the video screen is set at 75Hz Do not exceed 60Hz when using the maximum resolution 5 f you have problems in installing the adapter video driver boot the computer in Safe Mode remove the Display Adapter at the Control Panel System Device Administrator and then reboot the computer to reinstall the adapter video driver Fa E 14 If problems repeatedly occur contact an authorized service center Check List Q amp A Self Test Feature Check Q amp A Question Answer How can change the Frequency can be changed by reconfiguring the video card frequency Note that video card support can vary depending on the version of the driver used Refer to the computer or the video card manual for details How can adjust the resolution Windo
63. of the TFT LCD screen wipe with a slightly moistened soft fabric 3 Do not spray water or detergent directly on the monitor e This may cause damage electric shock or fire 2 Use the recommended detergent with a smooth cloth 2 If the connector between the plug and the pin is dusty or dirty clean it properly with a dry cloth e A dirty connector can cause an electric shock or fire NE A Xe 2 Contact the Service Center or Customer Center for interior cleaning lint once a year CNEE J e Keep the product s interior clean Dust which has accumulated in the Q FON interior over an extended period of time may cause malfunction or fire p Notational Power Installation Clean Others O Other 2 Do not remove cover or back No user serviceable parts inside e his may cause an electric shock or fire e Refer servicing to qualified service personnel a gt 9 If your monitor does not operate normally in particular if there are any V unusual sounds or smells coming from it unplug it immediately and mA contact an authorized dealer or service e This may cause an electric shock or fire Be careful not to let water drip into the monitor or expose the monitor to moisture e This may cause malfunction an electric shock or fire e Especially avoid operating the monitor near water or outdoors where it could be exposed to snow or rain e j 2 If the monitor is dropped or the casing is damaged turn
64. olving heavy text 3 Internet Medium Brightness For working with a mixture of images such as text and graphics 4 Entertain High Brightness For watching motion pictures such as a DVD or VCD gt gt Click here to see an animation clip 3 Brightness button 0 a is not on the screen Push the button to adjust 2 3 Adjust buttons Y A Adjust items in the menu 4 Enter button Activates a highlighted menu item 5 Auto button Use this button for auto adjustment 6 Power button Use this button for turn the monitor on and off 7 Power indicator This light glows green during normal operation and blinks green once as the monitor saves your adjustments v See PowerSaver described in the manual for further information regarding power saving m 1 functions For energy conservation turn your monitor OFF when it is not needed or when leaving it unattended for long periods Unpacking Front Rear Rear The configuration at the back of the monitor may vary from product to product 1 Power port Connect the power cord for your monitor to the power port on the back of the monitor 2 D sub 15 pin port Connect the signal cable to the 15 pin D sub connector on the back of your monitor MA ke See Connecting the Monitor for further information regarding cable connections SyncMaster 915N everyone s invite m Safety Instructions ida Setup M Adjusting Your Monitor Troubleshooting Specific
65. on ho select the deme dee hom fet window does nor quasntes that he hret pos choca well ba he beret match lor your hahaa 7 Click the Browse button then choose A D Driver and choose your monitor model in the model list and click the Next button Install From Disk Inget Iha mamulachurer s insballabon dek and then make sure thal the correct dime 6 selected below Copy manul acturer s Mes trom Hardware Update Wizard Sold the dewee diei pou want e install bor thio haide Z Tolasi the mamuo and modal of par kanaan Geese rel em click ed IF una Paia a dik hal Sanang ee lo riball ebek Hives Dok Medid ByncM ates 1715 119G 12005 Hagar 01795 E This dore iz pent detalle signed Lale de derent rin ii maala Hawa Drak ge J nes cano 8 If you can see following Message window then click the Continue Anyway button Then click OK button Hardware Installation The softwere pou ane installing for this hardeare S5yncM astes 17118417357 1705 MagecSyncMasber XT 755 has molt passed Windows Logo bating ko wendy it compabbdiy wth indes PP T edi pros vehi Mist bating is impaitard Continuing pour installation of thiz soften map impi or destabilize the correct operation of your system either immediately or m the future Mirozoft strongly commends thal pow stop Ihis installation now and contact the hardware vendor for zoftean that has passed Windows Logo testing puwang This
66. on your monitor follow these steps 1 Choose OK button on the Insert disk window 2 Click the Browse button on the File Needed window 3 Choose A D Driver then click the Open button and then click OK button How to install 1 Click Start Setting Control Panel 2 Double click the Display Icon 3 Choose the Settings tab and then click Advanced 4 Choose Monitor Case1 1f the Properties button is inactive it means your monitor is properly configured Please stop installation Case2 If the Properties button is active click the Properties button then follow next steps continually 5 Click Driver and then click on Update Driver then click on the Next button 6 Choose Display a list of the known drivers for this device so that can choose a specific driver then click Next and then click Have disk 7 Click the Browse button then choose A D Driver 8 Click the Open button then click OK button 9 Choose your monitor model and click the Next button then click Next button 10 Click the Finish button then the Close button If you can see the Digital Signature Not Found window then click the Yes button And click the Finish button then the Close button Microsoft Windows Millennium Operating System Click Start Setting Control Panel Double click Display icon Select the Settings tab and click Advanced Properties button Sel
67. onal Power Installation Clean Others Installation Be sure to contact an authorized service center when installing your monitor in a location with the heavy dust high or low temperatures high humidity chemical substance and where it operates for 24 hours such as the airport the train station or etc Failure to do so may cause a serious damage to your monitor er Put your monitor in a location with low humidity and a minimum of dust i d Lan aL PO R n v e Failure to do so may cause an electric shock or fire inside the monitor 2 Do not drop the monitor when moving it e his may cause damage to the product or human body Install the monitor base in a showcase or shelf so that the end of the base does not project beyond the showcase or shelf e Dropping the product may cause damage to the product or personal injury Set down the monitor carefully e The monitor could be damaged or broken Do not place the monitor face down e The TFT LCD surface may be damaged Installing a wall bracket must be done by a qualified professional e Installation by unqualified personnel may result in injury e Always use the mounting device specified in the owner s manual Install the product keeping a distance of 10 cm from the wall for ventilation purposes e An overheated product may catch fire Notational Power Installation Clean Others Clean When cleaning the monitor case or the surface
68. or for further information regarding cable connections SyncMaster 913N 915N 2 ng AA a w ul c everyone s invite m Safety Instructions Introduction M Adjusting Your Monitor Troubleshooting X Specifications E Information Connecting the Monitor Using the Stand Installing the Monitor Driver Installing the Monitor Driver Natural Color i Automatic Manual Rear of Computer Rear of Monitor z TURAE LIT i New Model Macintosh 1 Connect the power cord for your monitor to the power port on the back of the monitor Plug the power cord for the monitor into a nearby outlet 2 1 Using the D sub Analog connector on the video card Connect the signal cable to the 15 pin D sub connector on the back of your monitor 2 2 Connected to a Macintosh Connect the monitor to the Macintosh computer using the D SUB connection cable 2 3 In the case of an old model Macintosh you need to connect the monitor using a special Mac adapter 3 Turn on your computer and monitor If your monitor displays an image installation is complete SyncMaster 913N 915N Connecting the Monitor Using the Stand Installing the Monitor Driver Installing the Monitor Driver Natural Color Automatic Manual Monitor Assembly Monitor and Bottom 2 Pivot Stand A Stand Stopper Attaching a base This monitor accepts a 100 mm x 100 mm VESA
69. our Monitor Troubleshooting E Specifications Information Service Terms For Better Display Authority Regulatory Image Retention Free Service The address and phone number of the company can be changed without previous notice 2 AUSTRALIA Samsung Electronics Australia Pty Ltd Customer Response Centre 7 Parkview Drive Homebush Bay NSW 2127 Tel 1300 362 603 http www samsung com au 2 BRAZIL Samsung Eletronica da Amazonia Ltda R Prof Manoelito de Ornellas 303 Terro B Chacara Sto Antonio CEP 04719 040 Sao Paulo SP SAC 0800 124 421 http www samsung com br 2 CANADA Samsung Electronics Canada Inc Samsung Customer Care 7037 Financial Drive Mississauga Ontario L5N 6R3 1 800 SAMSUNG 1 800 726 7864 http www samsung ca 2 CHILE SONDA S A Teatinos 550 Santiago Centro Santiago Chile Fono 56 2 5605000 Fax 56 2 5605353 56 2 800200211 http www sonda com http www samsung cl COLOMBIA Samsung Electronics Colombia Cra 9 No 99A 02 Of 106 Bogota Colombia Tel 9 800 112 112 Fax 571 618 2068 http www samsung latin com e mail soporte samsung latin com ESPANA Samsung Electronics Comercial Iberica S A Ciencies 55 65 Poligono Pedrosa 08908 Hospitalet de Llobregat Barcelona Tel 93 261 67 00 Fax 93 261 67 50 http samsung es 2 FRANCE SAMSUNG ELECTRONICS FRANCE Service Paris Nord 2 66 rue des Vanesses BP 50116 Villepinte 95950 Roissy CDG Cedex T
70. ovide the best operating conditions and monitor settings In most cases monitor installation will proceed automatically unless the user wishes to select alternate settings Dot Acceptable TFT LCD panel manufactured by using advanced semiconductor technology with precision of 1ppm one millionth above is used for this product But the pixels of RED GREEN BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen This is not from bad quality and you can use it without uneasiness e For example the number of TFT LCD sub pixels that is contained in this product are 3 932 160 Note Design and specifications are subject to change without prior notice General PowerSaver Preset Timing Modes 9 PowerSaver This monitor has a built in power management system called PowerSaver This system saves energy by switching your monitor into a low power mode when it has not been used for a certain amount of time The monitor automatically returns to normal operation when you press a key on the keyboard For energy conservation turn your monitor OFF when it is not needed or when leaving it unattended for long periods The PowerSaver system operates with a VESA DPMS compliant video card installed in your computer Use a software utility installed on your computer to set up this feature Power saving mode State Normal Operation EPA ENERGY 2000 Power Switch off Power Indicator Green Green Blinking Black Less than 1W Le
71. plies with SWEDAC MPR II recommendations for reduced electric and magnetic fields European Notice Europe Only Products with the CE marking comply with the EMC Directive 89 336 EEC 92 31 EEC 93 68 EEC and the Low Voltage Directive 73 23 EEC issued by the Commission of the European Community Compliance with these directives implies conformity to the following European Norms e EN55022 1998 A1 2000 Radio Frequency Interference e EN55024 1998 Electromagnetic Immunity e EN61000 3 2 1995 A1 A2 1998 Power Line Harmonics e EN61000 3 3 1995 Voltage Fluctuations PCT Notice A546 VCCI This is a Class B product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment VCCI If this is used near a radio or television receiver in a domestic environment it may cause radio interference Install and use the equipment according to the instruction manual TCO 95 Ecological requirements for personal computers TCO 95 applied model only AB general requirements AB2 Written Eco document acompanying the products Congratulations You have just purchased a TCO 95 approved and labelled product Your choice has provided you with a product developed for professional use Your purchase has also contributed to reducing the burden on the environment and to the further development of environmentally adapted electronic products Why do we have environmentally labelled monitor
72. pment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television receptions which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help User Information Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment If necessary consult your dealer or an experienced radio television technician for additional suggestions You may find the booklet called How to Identify and Resolve Radio TV Interference Problems helpful This booklet was prepared by the Feder
73. referring to the video card manual and the Preset Timing Modes The maximum frequency per resolution may differ from product to product Windows ME 2000 XP Set the colors properly at the Control Panel Display Settings changing the video Has the video card been set Set the video card by referring to the card properly video card manual There is a message Have you installed the monitor Install the monitor driver according that reads driver to the Driver Installation Instructions Unrecognized monitor Plug amp Play See the video card manual to see if Install the monitor driver according VESA DDC monitor the Plug amp Play VESA DDC to the Driver Installation Instructions found function can be supported Magic Tune doesn t Have you changed your PC or Download the latest program work properly video graphic card The program can be downloaded from the http www samsung com Check the following items if there is trouble with the monitor Check if the power cord and the video cables are properly connected to the computer 2 Check if the computer beeps more than 3 times when booting If it does request an after service for the main board of the computer 3 If you installed a new video card or if you assembled the PC check if the installed the adapter video driver and the monitor driver 4 Check if the scanning ratio of the video screen is set at 75Hz Do not exceed 60Hz when using the maximum resolution
74. reset Timing Modes Horizontal Vertical Pixel Clock Frequency Sync Polarity Display Mode IBM 640 x 350 IBM 640 x 480 IBM 720 x 400 MAC 640 x 480 MAC 832 x 624 MAC 1152 x 870 VESA 640 x 480 VESA 640 x 480 VESA 800 x 600 VESA 800 x 600 VESA 800 x 600 VESA 800 x 600 VESA 1024 x 768 VESA 1024 x 768 VESA 1024 x 768 VESA 1152 x 864 VESA 1280 x 1024 VESA 1280 x 1024 kHz 31 469 31 469 31 469 35 000 49 726 68 681 37 500 37 861 35 156 37 879 46 875 48 077 48 363 56 476 60 023 67 500 63 981 79 976 Hz 70 086 59 940 70 087 66 667 74 551 75 062 75 000 72 809 56 250 60 317 75 000 72 188 60 004 70 069 75 029 75 000 60 020 75 025 Horizontal Frequency Frequency MHz 25 175 25 175 28 322 30 240 57 284 100 00 31 500 31 500 36 000 40 000 49 500 50 000 65 000 75 000 78 750 108 00 108 00 135 00 H V The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle and the inverse number of the Horizontal Cycle is called Horizontal Frequency Unit kHz Vertical Frequency Like a fluorescent lamp the screen has to repeat the same image many times per second to display an image to the user The frequency of this repetition is called Vertical Frequency or Refresh Rate Unit Hz SAMSUN everyone s inv So AA E Safety Instructions Introduction E Setup W Adjusting Y
75. ription Play Stop Adjust the Brightness Brightness Direct Access Feature When OSD is not on the screen Q Q Push the button to adjust brightness Contrast Adjust the Contrast Q D Color 2 SOURCE Menu Description Play Stop Color Ton The tone of the color can be changed and one of four Q Q modes can be selected Cool normal Warm and Custom Follow these steps to adjust individual R G B color Q Q Color Control balance Gamma Select one of three pre defined gammas Q Q O Image SOURCE Menu Description Play Stop Removes noise such as vertical stripes Coarse adjustment may move the screen image area You may Q Q relocate it to the center using the Horizontal Control menu Available in analog Mode Only Coarse Removes noise such as horizontal stripes If the noise persists even after Fine tuning repeat it after adjusting the Hing frequency clock speed 2 Q Available in analog Mode Only Sharpness Follow these instuction to change the clearance of image Follow these instructions to change the horizontal position H Position of the monitor s entire display Available in analog Mode Only Follow these instructions to change the vertical position of V Position the monitor s entire display Available in analog Mode Only SOURCE Description Play Stop Follow these steps to change the language used in the menu You can choose one of seven languages Englis
76. s e t may cause a fire or an electric shock If an alien substances or water flows into the product turn the product off unplug the power connector from the wall outlet and contact service center 3 If you view a fixed screen for an extended period of time residual image or blurriness may appear e Change the mode to energy save or set a screensaver to moving picture when you need to be away from the monitor for an extended period of time 2 Adjust the resolution and frequency to the levels appropriate for the model e Inappropriate resolution may cause undesirable picture quality 15inch 1024 X 768 17 19 inch 1280 X 1024 3 Watching the monitor continuously at a too close angle may result in eyesight damage To ease eye strain take at least a five minute break after every hour of using the monitor 3 Do not install the product on an unstable uneven surface or a location prone to vibrations e Dropping the product may cause damage to the product or personal injury Using the product in a location prone to vibrations may shorten the lifetime of the product or may catch fire 2 When moving the monitor turn the power switch off and unplug the power cord Make sure that all cables including the antenna cable and cables connected to other devices are disconnected before moving the monitor e Failure to disconnect the cable may damage it and lead to fire or an electric shock SyncMaster 913N n
77. s In many countries environmental labelling has become an established method for encouraging the adaptation of goods and services to the environment The main problem as far as monitors and other electronic equipment are concerned is that environmentally harmful substances are used both in the products and during their manufacture Since it has not been possible so far for the majority of electronic equipment to be recycled in a satisfactory way most of these potentially damaging substances sooner or later enter Nature There are also other characteristics of a monitor such as energy consumption levels that are important from both the working and natural environment viewpoints Since all types of conventional electricity generation have a negative effect on the environment acidic and climate influencing emissions radioactive waste etc it is vital to conserve energy Electronic equipment in offices consumes an enormous amount of energy since it is often routinely left running continuously What does labelling involve This product meets the requirements for the TCO 95 scheme which provides for international environmental labelling of monitors The labelling scheme was developed as a joint effort by the TCO The Swedish Confederation of Professional Employees Naturskyddsforeningen The Swedish Society for Nature Conservation and NUTEK The National Board for Industrial and Technical Development in Sweden The requirements cover a wid
78. s the printed or scanned images For more information refer to Help F1 in the software program How to install the Natural Color software Insert the CD included with the Samsung monitor into the CD ROM Drive Then the initial screen of the program Natural Color will be executed Click Natural Color on the initial screen to install the Natural Color software To install the program manually insert the CD included with the Samsung monitor into the CD ROM Drive click the Start button of Windows and then select Execute Enter D color eng setup exe and then press the lt Enter gt key If the drive where the CD is inserted is not D enter the applicable drive How to delete the Natural Color software program Select Setting Control Panel on the Start menu and then double click Add Delete a program Select Natural Color from the list and then click the Add Delete button SyncMaster 913N 915N B Safety Instructions E Introduction E Setup ii talus Troubleshooting Specifications E Information User Control Buttons Direct Functions OSD Functions subay MagicTune 1 Use this button for open the on screen menu and exits from the menu screen or closes screen adjustment menu This buttons allows you to adjust items in the menu This buttons allows you to adjust items in the menu Press this button activates a highlighted menu item a gt w m Press to self adjust to the incoming PC signal The values of
79. se change to the recommended mode during this one minute period The message is displayed again if the system is rebooted The monitor is in PowerSaver mode press a key on the keyboard to activate the monitor and restore the image on the screen If there is still no image press the Source button Then press any key on the keyboard again to activate the monitor and restore the image on the screen You may get a blank screen if you boot the system before you connect the DVI cable or disconnect and then reconnect the DVI cable while the system is running as certain types of graphic cards do not send out video signals Connect the DVI cable and then reboot the system Check the signal cable connection Make sure the video card is fully inserted in it s slot Reboot the computer Set the video card by referring to the video card manual Adjust screen image position and size using the OSD Adjust the resolution and frequency at the video card Refer to the Preset Timing Modes The screen can be unbalanced due to the cycle of the video card signals Readjust Position by referring to the OSD Have you adjusted the resolution or frequency on the monitor Is the frequency properly adjusted when checking the Display Timing on the menu Have the Windows colors been set properly Adjust the resolution and frequency of the video card Refer to the Preset Timing Modes Adjust the frequency properly by
80. ss than 1W Power Consumption Less than 38W Off mode 120Vac This monitor is EPA ENERGY STAR compliant and ENERGY2000 compliant when used with a computer equipped with VESA DPMS functionality As an ENERGY STAR Partner SAMSUNG has determined that this ENERGY STAR product meets the ENERGY STAR guidelines for energy efficiency General PowerSaver Preset Timing Modes Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes the screen will be adjusted automatically However if the signal differs the screen may go blank while the power LED is on Refer to the video card manual and adjust the screen as follows Table 1 Preset Timing Modes Horizontal Vertical Pixel Clock Frequency Display Mode Sync Polarity Frequency MHz H V IBM 640 x 350 IBM 640 x 480 IBM 720 x 400 MAC 640 x 480 MAC 832 x 624 MAC 1152 x 870 VESA 640 x 480 VESA 640 x 480 VESA 800 x 600 VESA 800 x 600 VESA 800 x 600 VESA 800 x 600 VESA 1024 x 768 VESA 1024 x 768 VESA 1024 x 768 VESA 1152 x 864 VESA 1280 x 1024 VESA 1280 x 1024 kHz 31 469 31 469 31 469 35 000 49 726 68 681 37 500 37 861 35 156 37 879 46 875 48 077 48 363 56 476 60 023 67 500 63 981 79 976 Hz 70 086 59 940 70 087 66 667 74 551 75 062 75 000 72 809 56 250 60 317 75 000 72 188 60 004 70 069 75 029 75 000 60 020 75 025 Horizontal Frequency 25
81. t to the SAMSUNG ELECTRONICS product identified above The SAMSUNG ELECTRONICS software product may include associated software components media printed materials and online or electronic documentation SOFTWARE PRODUCT By installing copying or using the SOFTWARE PRODUCT vou agree to be bound by the terms of this EULA IF vou do not agree to the terms of this EULA vou C do not accept the terms of the license agreement Back Next gt Cancel lnstallohreld Choose a folder to install the MagicTune program MagicTune 2 5 InstallShield Wizard Choose Destination Location Select folder where setup will install files x Install Magic T une 2 5 to GC Program Files S ELM agic T une 2 5 Change lnestallShreld Click Install MagicT une 2 5 InstallShield Wizard Ready to Install the Program The wizard iz ready to begin installation Click Install to begin the installation IF you want to review ar change any of pour installation settings click Back Click Cancel to exit the wizard Erster sat Cancel The Installation Status window appears MagicT une 2 5 InstallShield Wizard Setup Status retenta c 9 Click Finish MagicT une 2 5 InstallShield Wizard InstallShield Wizard Complete The InstallShield Wizard has successfully installed MagicT une 2 5 Click Finish to exit the wizard Pante Magic Tune 23 Double click the icon to
82. tact the Service Center or your dealer Can you see Not Optimum You can see this message when the Mode Recommanded Mode signal from the video card exceeds 1280 x 1024 60Hz on the screen the maximum resolution and frequency that the monitor can handle properly Adjust the maximum resolution and frequency that the monitor can handle properly If the display exceeds SXGA or 75Hz a Not Optimum Mode Recommanded Mode 1280 x 1024 60Hz message is The screen shows strange colors or just black and white The screen suddenly has become unbalanced The screen is out of focus or OSD cannot be adjusted LED is blinking but no images on the screen There are only 16 colors shown on the screen The screen colors have changed after There is no image on the screen Is the power indicator on the monitor blinking at 1 second intervals Connected using the DVI cable Is the screen displaying only one color as if looking at the screen through a cellophane paper Have the screen colors become strange after running a program or due to a crash between applications Has the video card been set properly Have you changed the video card or the driver Have you adjusted the resolution or frequency to the monitor displayed If the display exceeds 85Hz the display will work properly but the Not Optimum Mode Recommanded Mode 1280 x 1024 60Hz message appears for one minute and then disappears Plea
83. the monitor off se PL F9 and unplug the power cord LENI US y Ve e The monitor may malfunction causing an electric shock or fire editas e Then contact the Service Center 2 Disconnect the plug from the outlet during storms or lightening or if it is EL not used for a long period of time RU Ap E E io il i a i ui NW e Failure to do so may cause an electric shock or fire clip L i 2 Do not try to move the monitor by pulling only the wire or the signal cable e This may cause a breakdown electric shock or fire due to damage to the cable 3 Do not move the monitor right or left by pulling only the wire or the signal cable e This may cause a breakdown electric shock or fire due to damage to the cable 2 Do not cover the vents on the monitor cabinet e Bad ventilation may cause a breakdown or fire 3 Do not place water containers chemical products or small metal objects on the monitor e This may cause malfunction an electric shock or fire e f a foreign substance enters the monitor unplug the power cord and contact the Service Center 3 Do not use or store inflammable substances near the monitor e This may cause an explosion or fire 3 Never insert anything metallic into the monitor openings e his may cause an electric shock fire or injury 2 Do not insert metal objects such as chopsticks wire and gimlet or inflammable objects such as paper and match into the vent headphone port or AV port
84. tion are adjusted automatically Position Adjusts the screen location horizontally and vertically SPSS SSS SSS STS SSS PSPS SS SS SSS PSPSPS SSS SSS STS ESTES PSS SSS STS SSS SSS ST SPSS CST ST SST d s Option Tab Definition You can configure MagicTune using the following options Cancel Loads the Preferences Dialog Box Preferences in use will have an V in the check box To turn on or off any Preference position the cursor over the box and click e Enable task tray menu To access the MagicTune menus click the icon on the task tray menu The menus are not displayed if the Enable System Tray is deselected in Preferences Options Basic Settings e Select Language The language chosen affects only the language of the OSD Source Select e Analog e Digital ERE AAA AFA AI AFA dee 2 Support Tab Definition Shows the Asset ID and the version number of the program and allows you to use the Help feature MagicTune Support Goto Wagiclune Web ite Asset ID Jpen User Manual Version Cancel Visit the MagicTune website or click to open the Help files User Manual if you need any Help help installing or running MagicTune The User Manual opens within a basic browser window Asset ID Opens a monitor info window showing the manufacturing date of the monitor Version Displays the version of MagicTune Specifications subject to change without notice MagicTune is a trademark of 5AMSUNG ELECTRONICS CO
85. tted in the back light system of flat panel monitors as today there is no commercially available alternative TCO aims on removing this exception when a Mercury free alternative is available CFCs freons The relevant TCO 99 requirement states that neither CFCs nor HCFCs may be used during the manufacture and assembly of the product CFCs freons are sometimes used for washing printed circuit boards CFCs break down ozone and thereby damage the ozone layer in the stratosphere causing increased reception on earth of ultraviolet light with e g increased risks of skin cancer malignant melanoma as a consequence Lead Lead can be found in picture tubes display screens solders and capacitors Lead damages the nervous system and in higher doses causes lead poisoning The relevant TCO 99 requirement permits the inclusion of lead since no replacement has yet been developed TCO 03 Ecological requirements for personal computers TCO 03 applied model only DISPLAYS www tcodevelepment com Congratulations The display you have just purchased carries the TCO 03 Displays label This means that your display is designed manufactured and tested according to some of the strictest quality and environmental requirements in the world This makes for a high performance product designed with the user in focus that also minimizes the impact on our natural environment Some of the features of the TCO 03 Display requirements Ergonomics Good
86. uctions may cause harmful interference to other devices in the vicinity However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to other devices which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving device e Increase the separation between the equipment e Connect the equipment into an outlet on a circuit different from that to which the other device s are connected e Consult the manufacturer or field service technician for help Video In RS 232 Video Out Accessories equipment connected to the analog and digital interfaces must be certified to the respective IEC standards i e IEC 950 for data processing equipment and IEC 601 1 for medical equipment Furthermore all configurations shall comply with the system standard IEC 601 1 1 Everybody who connects additional equipment to the signal input part or signal output part configures a medical system and is therefore responsible that the system complies with the requirements of the system standard IEC 601 1 1 If in doubt consult the technical services department or your local representative Transport and Storage Limitations Temperature Range of 40 C to 70 C Relative Humidity of 10 95 non condensing Bio accumulative is defined as substances
87. which accumulate within living organisms Lead Cadmium and Mercury are heavy metals which are Bio accumulative Mercury Statement LCD Monitor LCD TV DLP Projection TV Projector for USA only 2 LAMP S INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL STATE OR FEDERAL LAWS For details see lamprecycle org eiae org or call 1 800 Samsung PRODUCT INFORMATION Image Retention Free LCD Monitors and TVs may have image retention when switching from one image to another especially after displaying a stationary image for a long time This guide is to demonstrate correct usage of LCD products in order to protect them from Image retention What is Image retention During normal operation of a LCD panel pixel image retention doesn t occur However if the same image is displayed for a long time a slight difference in electric charge accumulates between the two electrodes which encase the liquid crystal This may cause the liquid crystal to build up in a certain areas of the display Thus the previous image is retained when switching to a new video image All display products including LCD are subject to image retention This is not a product defect Please follow the suggestions below to protect your LCD from image retention Power Off Screen Saver or Power Save Mode Ex e Turn the power off when using a stationary pattern Turn the power off for 4 hours after 24 hours in use Turn
88. ws ME XP 2000 Set the resolution at the Control Panel Display Settings Contact the video card manufacturer for details How can set the Power Saving Windows ME XP 2000 Set the function at BIOS SETUP of the function computer or the screen saver Refer to Windows Computer Manual How can clean the outer Disconnect the power cord and then clean the monitor with a soft case LCD Panel cloth using either a cleaning solution or plain water Do not leave any remains of the detergent nor scratch the case Do not allow any water to go inside the monitor Check List Q amp A Self Test Feature Check Self Test Feature Check Self Test Feature Check Warning Messages Environment Useful Tips Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly Self Test Feature Check 1 Turn off both your computer and the monitor 2 Unplug the video cable from the back of the computer 3 Turn on the monitor If the monitor is functioning properly you will see a box in the illustration below Check Signal Cable This box appears during normal operation if the video cable becomes disconnected or damaged 4 Turn off your monitor and reconnect the video cable then turn on both your computer and the monitor If your monitor screen remains blank after using the previous procedure check your video controller and computer system your monitor is functioning properly

Samsung SyncMaster 915N 19" Flat Panel LCD Monitor

Contents

Download Pdf Manuals

Related Search

Related Contents

Samsung SyncMaster 915N 19&quot; Flat Panel LCD Monitor

Contents

Download Pdf Manuals

Related Search

Related Contents

Samsung SyncMaster 915N 19" Flat Panel LCD Monitor