Hitachi (CDR-8130) Burner
Contents
1. ATTENTION RADIATION DU FAISCEAU LASER INVISIBLE EN CAS D OUVERTURE EVITER TOUTE EXPOSITION AUX RAYONS ADVARSEL USYNLIG LASERSTRALING VED ABNING NAR SIKKERHEDSAFBRYDERE ER UDE AF FUNCTION SE IKKE IND STRALEN HELLER IKKE MED OPTISKE INSTRUMENTER l ADVARSEL USYNLIG LASERSTR LING N R DEKSEL PNES OG SIKKERHEDSLAS BRYTES STIRR IKKE INN STRALEN ELLER SE DIREKTE MED OPTISKE INSTRUMENTER VARNING OSYNLIG LASERSTRALNING N R DENNA DEL AR PPNAD OCH SPARREN AR URKOPPLAD STIRRA EJ IN STRALEN OCH BETRAKTA EJ STRALEN GENOM OPTISKT INSTRUMENT AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA NAKYMATTOMALLE LASER SATEILYLLE ALA TUIJOTA SATEESEEN L K KATSO SIT OPTISEN For Europe Caution Use of controls or adjustments or peformance of procedures other than those specified herein may resultin hazardous radiation exposure DEFINITIONS AND A SYMBOL The following symbol and signal word are used throughout this instruction manual with the following definitions This symbol indicates any condition or particle which if not A strictly observed could result in damage or destruction of the e IMPORTANT Important notes indicate a subject of common errors in operation or maintenance h IMPORTANT SAFEGUARDS SAFETY POINTS YOU SHOULD KNOW ABOUT YOUR EQUIPMENT READ ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS FOR LATER USE FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED ON THE PRODUCT PRECAUTIONS FOR SAFETY Powe2. SISTEME VERTRIEBS GHBH in GERMANY and by SAEC COMMERCE CO LTD in JAPAN 1 Turn on the CD ROM Drive 2 Using the small brush supplied with the cleaning disc case straighten up the disc cleaning brushes on the back of the cleaning disc 3 Place the cleaning disc in the Disc Tray with its arrow marked on the disc at front 4 Press the OPEN CLOSE button or push the center of the Disc Tray lightly and close the Disc Tray 5 In about 20 seconds the pick up lens is cleaned by the cleaning disc 6 Press the OPEN CLOSE button and remove the cleaning disc 7 Set the cleaning disc in its case with the disc cleaning brushes in the pad hole 8 Restart the SYSTEM TROUBLESHOOTING If your CD ROM Drive does not operate properly check the following table You may have to check the other devices included in your SYSTEM If you can not locate the cause turn off the power of the SYSTEM including the CD ROM Drive and unplug the power supply cable of the SYSTEM from the wall outlet immediately and contact your dealer When calling for service provide the following information 1 Model name 2 Detailed symptoms 10 The CD ROM 1 You place the disc up side 1 Place the disc right side up in the Drive does not down in the Disc Tray Disc Tray then load it operate even when 2 The disc is dirty 2 Clean the disc surface See page 4 a disc is loaded 3 The pick up lens is 3 Clean up the pick up lens See page dirty 10 4
3. damaged If your CD ROM Drive exhibits a distinct change in performance Do not install your CD ROM Drive under the following conditions It may lead to trouble or affect performance by dust on the pick up lens and the disc by heat or vibration In a place where an operation temperature reaches beyond the specified temperature 40C High humidity locations In a location subject to extreme changes of temperature and humidity In a room where dust density higher than 0 1 mg m In a room that has air conditioning with humidity control which may scatter calcium combinations and other powdered substances In a room containing exhaust gas fumes such as exhaust gas from gasoline or diesel engines or corrosive gas such as H2S Hydrogen sulfide In a location subject to vibration and jarring during drive operation In a location subject to sudden shock and jolt during drive operation Mounting requirements Mount your CD ROM drive tightly in horizontal or vertical position by screws The inclination of your CD ROM Drive should be within 5 as shown below If you do not When the Disc Tray is opened the disc may jump out and may be damaged It may cause damage to your CD ROM drive Your CD ROM Drive may not work with full performance Mounting screw The screws must be ISO M3 x 0 5 to mount the CD ROM Drive tightly and avoid damaging the mechanism inside the CD ROM Drive See page 11 Moving your CD ROM D
4. 200 2 400 kbytes s Mode 1 1k 2 1 024 Access Time Average 1 3 Stroke 90 ms Typical Note 1 Full Stroke 150 ms Typical Note 2 Notes 1 Average of 100 access operations between 15 min 00 s 00 block and 35 min 00 s 00 block with latency 2 Average of 100 access operations between 00 min 02 s 00 block and 59 min 59 s 74 block with latency AUDIO PERFORMANCE Number of Channels 2 Output Level Line 0 7 Vrms TYP 47 kohms load Headphone 0 6 Vrms TYP 32 ohms load Output Terminal Line 4 pin terminal 2 54 mm pitch Headphone out 3 5 mm Jack RELIABILITY Data Error Rate 10 or less Mode 1 10 or less Mode 2 Raw error rate assumed to be 10 or less INTERFACE ATAPI BUS 40 pin non shielded connector Note Design and specifications are subject to change without prior notice Hitachi has done everything possible to prevent the failure of the CDR 8130 However it is not absolutely free from failure In case it should fail Hitachi is not responsible for the results 12
5. Change the disc 4 The disc is scratched or warped 5 Turn off your SYSTEM and re 5 Cable connection is connect cables correctly incorrect The Disc Tray can The program is incorrect It Check the program Check the not beopened is locked by the program program Communications There are devices with the Give each device a different Device between the host same Device Configuration Configuration Jumper setting computer and the jumper setting on the devices on the interface cable interface cable can not be done MECHANICAL DIMENSIONS A Hole 5 max Surface of the CD ROM DRIVE Mounting Screw M3X0 5 Mounting frame of the host computer Dimensions unit mm 11 PECIFICATION GENERAL Power Requirements DC Voltage 12V 10 1 0A 5V 5 0 7A Ripple 12V 300 mVpp maximum 5V 150 mVpp maximum Dimensions WxHxD 146 x 41 3 x 190 mm Excluding front panel Front panel 149 3 x 42 7 x 5mm Mass 0 95 kg Operating amp Storage Conditions Temperature 5 45 C operating 30 60 C non operating Relative humidity 15 85 RH operating non condensing 10 90 RH non operating non condensing PERFORMANCE Disc Diameter 120 mm 80 mm Rotational speed 71 3 52 7 s Approx 4 200 3 200 rpm Capacity 1M 27 1 048 576 650 Mbytes Mode 1 742 Mbytes Mode 2 Conditions 333 000 blocks 74 min for recorded area Record Side Single side Sustained Data Transfer Rate 1
6. INSTRUCTION MANUAL CD ROM DRIVE MODEL CDR 8130 IMPORTANT Read all of these instructions carefully and understand them before using your CD ROM drive Keep this instruction manual for future reference If this CD ROM drive changes ownership be sure this manual accompanies the CD ROM drive CONTENTS ee a all IMPORTANT SAFEGUARD 4 CONTROLS AND FUNCTIONS 6 INSTALLATION 7 DRIVE OPERATION 8 EMERGENCY EJECT PROCEDURE 9 LENS CLEANING 10 TROUBLESHOOTING 10 MECHANICAL DIMENSIONS 11 SPECIFICATIONS 12 C READ AND KEEP THIS MANUAL 1 For USA Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occu
7. er and mount tightly by screws Check the settings of the interface card Install the interface card in the slot Firmly attach the interface cable from the interface card to the CD ROM Drive Firmly attach Audio connecting cable as required Finally attach a spare DC power supply cable from the computer power supply to the CD ROM Drive firmly 10 Install the host computer cover NOAA N a R Power supply cable 1 CN Interface cable Audio connecting cable _ SOFTWARE INSTALLATION To install CD ROM device driver in the host computer to operate this CD ROM Drive refer to the instruction manual of each CD ROM device driver DRIVE OPERATION 1 Turn on the SYSTEM including the CD ROM Drive 2 Press the OPEN CLOSE button of the CD ROM Drive to open the Disc Tray 3 Place the disc in the center of the Disc Tray with label side up as shown below 4 To close the Disc Tray press the OPEN CLOSE button on the CD ROM Drive or push lightly the center of the front of the Disc Tray as shown below The disc Tray will close the rest of the way automatically 5 Operate referring to the instruction manual of CD ROM device driver cK 120 mm Disc 80 mm Disc Disc label side Disc label side z wa IMPORTANT Do not press the OPEN CLOSE button while the host computer is accessing the disc It may caused an error When not using the CD ROM Drive keep the Disc Tray closed It will prevent
8. r in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Re orientate or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Caution Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment For Germany Fur Deutschland Module d rfen nur an eine Sicherheits Kleinspannungs Versorgung SELV Kreise nach EN60950 VDE 0805 angeschlossen werden Die Trennung von Netzspannung muB durch einen Sicherheitstransformator geschehen The equipment is classified as a Class 1 level Laser product This label is fixed to the bottom of the CD ROM Drive CLASS 1 LASER PRODUCT S LASER KLASSE 1 PRODUKT LUOKAN 1 LASERLAITE KLASSE 1 LASERAPPARAT APPAREIL A LASER DE CLASSE 1 CAUTION INVISIBLE LASER RADIATION WHEN OPEN DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS VORSICHT UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEOFFNET NICHT IN DEN STRAHL BLICKEN AUCH NICHT MIT OPTISCHEN INSTRUMENTEN
9. r source This CD ROM Drive should be operated from the type of power source indicated on the marked label 12V DC 5V DC To avoid the risk of electric short circuits or damage to your CD ROM drive Do not expose your CD ROM Drive to rain or moisture Do not open or remove the cover of your CD ROM Drive It may cause personal injury by rapid rotating disc Turn off your SYSTEM and unplug the power supply cable of your SYSTEM from the wall outlet before installing your CD ROM Drive interface card or connecting cables Do not allow liquids and foreign objects to get in Do not place heavy loads on the CD ROM Drive Do not use this CD ROM Drive without mounting it Firmly attach the DC power supply cable connecting cables between the CD ROM Drive and other devices and keep them connected securely In case of failure In case of the following conditions turn off the SYSTEM including the CD ROM Drive and unplug the power supply cable of the SYSTEM from the wall outlet immediately Do not attempt to service the CD ROM Drive yourself and refer servicing to qualified service personnel immediately If objects of any kind have been entered into your CD ROM Drive If liquid has been spilled into your CD ROM Drive If your CD ROM Drive has been exposed to rain or water If your CD ROM Drive does not operate normally when the operating instructions are followed If your CD ROM Drive has been dropped or your CD ROM Drive has been
10. rive Remove the disc and close the Disc Tray before moving the CD ROM Drive If your CD ROM Drive is moved with the disc loaded or the Disc Tray opened both the disc and the CD ROM Drive may be damaged PRECAUTIONS FOR CARE Cleaning of the CD ROM Drive discs Never clean your CD ROM Drive and discs with silicon cloths or cloths soaked in water solvents thinner benzine abrasive cleaner anti static sprays any record cleaner sprays liquid cleaner or aerosol cleaner It may damage or discolor the coating of the CD ROM Drive or damage or deform discs Clean your CD ROM Drive including the Disc Tray and discs with a clean dry soft cloth at least once a month Clean your CD ROM drive s pick up lens using a cleaning disc CONTROLS AND FUNCTIONS Front Panel Rear Panel le Ga Glee 7 8 ao 1 LOADING UNLOADING BUSY Indicator Indicator blinks green only when the Disc Tray is being opened or closed or when the CD ROM drive is accessing data 2 Disc Tray When the power of the CD ROM Drive is turned off the Disc Tray can not be opened and closed 3 Headphone Jack 3 5 mm 4 Headphone Volume Control Adjust the headphone volume 5 OPEN CLOSE Button Press this button to open or close the Disc Tray 6 Manual Emergency Eject Hole Only in case of emergency If the Disc Tray does not open when the OPEN CLOSE Button is pressed the CD ROM Drive s Manual Emergency Eject mechanism may be activated This
11. should be used only in case of emergency See Page 9 about Manual Emergency Eject Procedure 7 Audio Output Terminal Lch GND Reh 8 Device Configuration Jumper This Connector is used to set operation modes such as Master Slave and CSEL Device is Master Circuit Board Device is 5 3 1 Slave Cable Select 9 ATAPI Interface Connector ATAPI bus connection 40 pin 10 Power Supply Connector DC Input For connecting the power supply cable Circuit Board 4 12V GND 5V INSTALLATION WHAT YOU NEED HARDWARE CD ROM Drive Interface card Interface cable Power supply cable Mounting screws HARDWARE OPTION Audio connecting cable Sound Card SOFTWARE CD ROM device driver If you need a interface card or interface cable or CD ROM device driver contact your dealer HARDWARE INSTALLATION To install this CD ROM drive in the host computer refer to the instruction manual of each host computer And to install the interface card in the host computer refer to the instruction manual of each host computer and each interface card Install the CD ROM Drive following general installation procedure shown below 1 Check the Device Configuration Jumper settings of the CD ROM Drive such as Master Slave CSEL See page 6 Turn off the host computer and unplug the power supply cable of the host computer Remove the host computer cover Install the CD ROM Drive into the host comput
12. the entry of the dust and dirt and reduce the requirements for disc and lens cleaning A CAUTION If you do not observe the following items troubles such as that the Disc Tray can not be opened or can not be closed may occur or it may cause damage to the mechanism of the CD ROM Drive Never use a damaged broken or deformed disc Do not press down hard on the Disc Tray when opening and closing the Disc Tray EMERGENCY EJECT PROCEDURE Only in case of emergency If the Disc Tray does not open when the OPEN CLOSE Button is pressed make sure that the power of the CD ROM Drive is turned on and software lock function has not been used If the Disc Tray still will not open the CD ROM Drive s Manual Emergency Eject mechanism may be activated This should be used only in case of emergency REMOVAL PROCEDURE 1 Turn off the CD ROM Drive and wait at least 15 seconds till the disc stops rotating 2 Insert the Eject bar for example a straightened paper clip into the Manual Emergency Eject Hole about 25 mm 1 inch 3 Pull the Disc Tray Do not use a breakable bar A broken bar inside the CD ROM Drive may cause a malfunction Eject bar Push Minimum straight length 30 mm Diameter 1 1 8mm Lens Cleaning A commercially available Laser Lens Cleaning Disc may be used to clean up the pick up lens of the CD ROM Drive Use the Compact Disc Laser Lens Cleaner LLC 1 oy AUDIO SOURCE in U S A by AKUSTIK
Download Pdf Manuals
Related Search