Sony KV-XJ29M50 29" TV
Contents
1. To audio A Audio cable output f not supplied component U video input N Signal flow To component Component video cable video output not supplied Notes e If your DVD player can output interlace and progressive mode signals select the interlace output when connecting to component video input on your TV Your TV can receive either 525i 60Hz or 625i1 50Hz interlace signals Some DVD player terminals may be labeled differently Connect To on the DVD player Y green Y Cs blue Cb B Y or Ps Cr red Cr R Y or Pr Since the high quality pictures on a DVD disc contain a lot of information picture noise may appear In this case adjust the sharpness SHARP see page 16 Using Your New TV 7 8 Securing the TV To prevent the TV from falling secure the TV using one of the following methods With the supplied screws attach the band to the TV stand and to the rear of the TV using the provided hole or Put the cord or chain through the clamps to secure the TV against a wall or pillar Note e Use only the supplied screws Use of other screws may damage the TV Using Your New TV Presetting channels Ve You can preset up to 100 TV channels in numerical sequence from program n number 1 using the remote and the Number buttons fe buttons on y2. or on the remote control once 4 Press to display FINE on the screen 5 Press or continuously until the above problems are minimized The or icon on the screen flashes while tuning 6 Press SELECT to return to normal screen Using Your New TV 11 12 Watching the TV This section explains functions used while watching the TV Most operations can be done using the remote Jo PROGR Lo Lo KO indicator aX VO E3 g Number buttons JUMP A PROGR SELECT or S amp R 23 1 Press to turn on the TV When the TV is in the standby mode the b indicator on the TV is lit red press I on the remote or PROGR on the TV 2 Press PROGR or the number buttons to select the program number For double digit numbers press then the number e g for 25 press then 2 and 5 PROGR eS or POOG OOGO 4 3 Press 4 to adjust the volume JO Using Your New TV Additional tasks To Press Turn off temporarily 1 The indicator on the TV lights up red Turn off completely on the TV Mute the sound OX Watch the video input VCR camcorder etc to select VIDEO 1 VIDEO 2 or DVD To return to the TV program press O Jump back to the previous program number JUMP Display the on screen inform
3. long as the power cord is plugged in the TV stand surface is flat and its area is larger Unplug the TV before moving it or if you are not than the bottom area of the TV going to use it for several days Using Your New TV Getting Started Connect the antenna If you wish to connect a VCR see the Connecting a VCR diagram below Antenna cable not supplied IEC connector not supplied Connecting a VCR To watch the video input press see page 13 To IT antenna To video and audio outputs video input f white Audio Video cable oa not supplied signal flow 4 Using Your New TV Notes e If you connect a monaural VCR connect the yellow plug to the yellow jack and the black plug to L MONO the white jack e If you connect a VCR to the IT antenna input terminal preset the signal output from the VCR to the program number 0 on the TV e Do not connect video equipment to the 2 video input jacks at the front and the rear of your TV at the same time otherwise the picture will not be displayed properly on the screen e When no signal is input from the connected video equipment the TV screen becomes blue CAUTION e Do not connect the power cord until you have completed making all other connections otherwise a minimum leakage current might flow through the antenna
4. S ONY 4 088 152 11 1 Trinitron Color TV Operating Instructions GB e Before operating the unit please read this manual thoroughly and retain it for future reference FD Trinitron WEGA KV XJ29 M80 M50 2002 Sony Corporation WARNING e Dangerously high voltages are present inside the TV e Operate the TV only between 110 240 V AC For your own safety do not touch any part of the TV the power cord and the antenna cable during lightning storms For children s safety do not leave children alone with the TV Do not allow children to climb onto To prevent fire or shock hazard do not expose the TV to rain or moisture Do not operate the TV if any liquid or solid object falls into it Have it checked immediately by qualified personnel only Do not block the ventilation openings of the TV Do not install the TV in a confined space such as a bookcase or built in cabinet by 4 Clean the TV with a dry and soft cloth Do not use benzine thinner or any other chemicals to clean the TV Do not scratch the picture tube Do not plug in too many appliances to the same power socket Do not damage the power cord Do not open the cabinet and the rear cover of the TV as high voltages and other hazards are present inside the TV Refer servicing and disposal of the TV to qualified personnel Your TV is recommended for home use only Do not use the TV in any vehicle or
5. and other terminals to ground e To avoid battery leakage and damage to the remote remove the batteries from the remote if you are not going to use it for several days If any liquid that leaks from the batteries touches you immediately wash it away with water Insert the batteries into the remote a 5 Ke S oO Note e Do not use old batteries nor use different types of batteries together Preset the channels automatically Front of TV VHF LOW B G Tips e If you want to stop automatic channel presetting press SELECT twice e If your TV has preset an unwanted channel or cannot preset a particular channel then preset your TV manually see page 10 Note e During automatic channel presetting your TV screen will indicate B G I D K or M for the TV system Using Your New TV 5 Connecting optional components You can connect optional audio video components such as a VCR multi disc player camcorder video game or stereo system To watch the video input of the connected equipment press see page 13 Connecting a camcorder video game equipment using the video input jacks Front of TV Audio Video cable not supplied ToS 2 To video and video input audio outputs Camcorder vy L MONO y R Video game equipment s2 Signal flow Notes e You can also conne
6. ation Adjust the volume of all program numbers automatically SELECT repeatedly until INTELLIGENT VOL appears then press or to select ON To cancel select OFF Adjust the picture position when it is not aligned to the TV screen SELECT repeatedly until PIC ROTATION appears then press or to adjust the alignment of the picture position PIC ROTATION eto The or OF icon on the screen flashes while adjusting The picture sound and either the program number or video input are displayed The on screen display for the picture and sound information disappears after about three seconds Changing the on screen display language 1 Press SELECT until SELECT m LANGUAGE wI ENGLISH gt appears on the screen LANGUAGE Wl ENGLISH m 2 Press or to select as ae es gt E gt LANGUAGE 2a gaS Tip e You can also use SELECT and z1 on the TV to select the on screen display language continued Using Your New TV C u Ss ice zZ oO 13
7. ct video equipment to the 1 or 2 video input jacks at the rear of your TV e Do not connect video equipment to the 2 video input jacks at the front and the rear of your TV at the same time otherwise the picture will not be displayed properly on the screen Connecting audio video equipment using the C gt monitor output jacks Antenna cable not supplied A Rear of TV To output or a R L Y amp monitor Se ar L a3 via output To video and To audio inputs audio inputs om yellow Audio Video cable p L MONO not supplied hit et ER A Signal flow Note e If you select DVD on your TV screen the signal from the gt monitor output jacks will not be output properly This does not indicate a malfunction 6 Using Your New TV Connecting a DVD player using the component video input jacks 1 Connect R and L under component video input on your TV to the LINE OUT AUDIO R and L output connectors on your DVD player 2 Using a component video cable connect Y Cs and Cr under component video input on your TV to the COMPONENT VIDEO OUT Y Cs and Cr output connectors on your DVD player DVD player Rear of TV Cc a Ss ice a oO COMPONENT VIDEO OUT S VIDEO OUT LINE OUT R AUDIO L VIDEO To L white R red amp
8. ess or to select the appropriate Be be See TV system until the picture or sound quality is optimal 10 Using Your New TV To change the color system setting If the color is abnormal when receiving programs through the I antenna input terminal or the video input jack 1 Press SELECT until COLOR SYS appears COLOR SYS AUTO amp lt 2 Press or to select the appropriate AUTO gt PAL gt SECAM 2 color system until the color is E gt optimal NTSC 4 43 lt NTSC 3 58 2 Tip lt e Normally set COLOR SYS to AUTO Skipping program numbers Press PROGR or the number buttons until the unused or unwanted program number appears Press SELECT until MANUAL PROGRAM appears Press or to enter the MANUAL PROGRAM mode Press PIC MODE Press SELECT to exit the MANUAL PROGRAM mode Ul WIN To restore the skipped program number again Preset the channel automatically or manually Tip e You can also use SELECT and 4 on the TV to preset channels and skip program numbers To use the fine tuning FINE function The fine tuning FINE function may help to reduce the following problems double images and lines moving across the TV screen You can use the fine tuning function as below 1 Select the program number you want to adjust 2 Press SELECT until MANUAL PROGRAM appears on the screen 3 Press
9. our TV as well a lt A PROGR 5 SELECT PIC MODE or Presetting channels automatically 1 Press to turn on the TV 2 Press AUTO PROGR Ag as gt VHF LOW B G I t Note e During automatic channel presetting your TV screen will indicate B G 1 D K or M for the TV system To preset channels automatically from a specified program number 1 Press SELECT until AUTO PROGRAM appears 2 Press or to enter the AUTO PROGRAM mode The on screen display will start flashing 3 Press PROGR or the number buttons until the desired program number appears 4 Press or to start presetting channels automatically continued Using Your New TV 9 Presetting channels continued Presetting channels manually 1 Press SELECT until SELECT E MANUAL PROGRAM gt appears MANUAL PROGRAM 2 Press or to enter the a MANUAL PROGRAM gt ee mode E VHF LOW B G N Jjjj 3 Press PROGR or the number buttons until the PROGR desired program number 4 000 appears or s s SOS 4 Press or until the desired channel picture appears gt E gt 5 Press SELECT to exit the SELECT m MANUAL PROGRAM mode To change the TV system setting If the picture or sound is abnormal when receiving programs through the TI antenna input terminal 1 Press SELECT until TV SYS appears TV SYS B G 2 Pr
10. where it may be subject to excessive dust heat moisture or vibrations Table of Contents Using Your New TV Getting Started sesccc vac sevice brasesctnsbsnccectindesaineysttbeve ned NER ee Kipa NERSE ESAR 4 c Step 1 Connect the antenna scis ccasesisisceseveterivevasasssceserevanennvarsesecessvenss 4 a Step 2 Insert the batteries into the remote ccceceeeeeteteteeseseees 5 s Step 3 Preset the channels automatically c ccccsecseseeeeseeseseseeees 5 S Connecting optional components OCU IT the TV asics eraa eee Eea aE aaie EEEE Presetting chatihels s s ii2 dwn niin ei A etic d Watching the TV 3 iiisnceasiviis ac eat eevee Advanced Operations Customizing the picture and SOUN 0 0 cece eee eens eeeeeeseeeeeens 15 Viewing your favorite Channels cseecssesssseseesssessesseeesseseessseseenseeees 18 Blocking the channels CHILD LOCK wesssisssissisiiisisresi isviso iasa 19 Additional Information Selfdiag nosis FUNCHON s sid sosirea irere iaat gaaei 20 Troubleshooting ascensos r 21 Overview Of cOntrOIS sies esiisrisins ssnsdin eiei as ean iianak 24 SPECAN ONS sepira aniani aesan eaaa pa in Si Back cover WARNING continued Pull the power cord out by the plug Do not pull the power cord itself Even if your TV is turned Install the TV on a stable TV stand and floor off it is still connected to the AC power source which can support the TV set weight Ensure that mains as
Download Pdf Manuals
Related Search