Belkin ReSource UPS System
Contents
1. ReSource IMPORTANT SAFETY INSTRUCTIONS e This manual contains important instructions for Model F5C500 F5C510 and F5C520 that should be followed during installation and maintenance of the UPS and batteries Please save this instruction manual e The unit is intended for installation in a temperature controlled indoor area free of conductive contaminants e To reduce the risk of fire connect only to a circuit provided with 20 amperes maximum branch circuit overcurrent protection in accordance with the National Electrical Code ANSI NFPA 70 e Servicing of batteries should be performed or supervised by personnel knowledgeable of batteries and the required precautions Keep unauthorized personnel away from batteries Setting up your ReSource 1 Plug ReSource into a 3 prong grounded outlet If the Wiring OK light does not light up please refer to the Wiring OK section below 2 Plug your PC power supply and monitor power supply to the outlets marked Instant Back Up Power Supplied Plug in any other devices that may require back up power in case of a utility power outage e g external storage drive or tape backup external modem 3 Printers and other peripherals that are not crucial to battery back up but still need maximum surge protection should be plugged into the four remaining outlets that are opposite the Instant Back Up Power Supplied outlets These outlets have full surge protection but are not powered by2. 11 A 125 V 1250W 10A Max Load for Battery Power Supplied outlets 4 outlets 325VA 180W 2 5 A 450VA 250W 3 6 A 600VA 330W 4 8 A Brownout Voltage Transfer to Battery 95 Vac typical 95 Vac typical 95 Vac typical 135 Vac typical 135 Vac typical Overvoltage Transfer to Battery 135 Vac typical On Battery Output Voltage 120 Vac 5 120 Vac 5 120 Vac 5 Transfer Time 3 ms typical 6 ms maximum 3 ms typical 6 ms maximum 3 ms typical 6 ms maximum 1 Surge Energy Rating H N H G N G 260 Joules 1260 Joules 1260 Joules EMI RFI Noise Filter Frequency Range 150kHz 100MHz Frequency Range 150kHz 100MHz Frequency Range 150kHz 100MHz Attenuation up to 58 db Attenuation up to 58 db Attenuation up to 58 db 32 to 95 F 0 to 35 C to 95 non condensing Typical Battery Recharge Time 2 hours from total discharge Typical Battery Life 6 years Size Lx Wx H 6 1 8 x 6 x 3 Net Weight 8 Lbs UL Listing 445 1778 Operating Temperature Operating Relative Humidity O l Important Safety Instructions This manual contains important instructions for Model F5C500 F5C510 and F5C520 that should be followed during installation and maintenance of the UPS and the batteries e The unit is intended for installation in a temperature controlled indoor area free of conductive contaminants e To reduce the risk of fire connect only to a circuit provided with 20 amperes maximum branch circuit overcurre
3. Belkin Components will spend to repair or replace the damaged connected equipment at Belkin s option an amount equal to the fair market value of the damaged equipment or the original purchase price of the equipment whichever is less up to the maximum amount set forth below For model F5C050 Series up to a maximum of 1 000 00 For model F5C550 Series up to a maximum of 5 000 00 For models F5C594 Series up to a maximum of 10 000 00 For models F5C572 Series up to a maximum of 20 000 00 For models F5C140 and F5C595 Series up to a maximum of 35 000 00 For models F5C240 F5C290 and F5C695 Series up to a maximum of 50 000 00 For model F5C500 up to a maximum of 35 000 00 For model F5C510 up to a maximum of 50 000 00 For model F5C520 up to a maximum of 75 000 00 For models F5C795 Series up to a maximum of 75 000 For model F5C895 TEL Unlimited Warranty The fair market value of the equipment shall be the current value of the equipment specified in the most recent edition of the Orion Blue Book by Orion Research Corporation Roger Rohrs Publisher Belkin Components reserves the right to review the damaged Belkin Surge Suppressor the damaged equipment and the site where the damage occurred All costs of shipping the Belkin Surge Suppressor and the damaged equipment to Belkin Components for inspection shall be borne solely by the purchaser Belkin reserves the right to negotiate the cost of repairs If Belkin determines in its sole disc
4. Installing Shutdown Software Shutdown Software This software closes all open files and saves them during a power failure The software is also installation friendly To install e Charge ReSource 2 4 hours before installing software e Connect RS232 cable to PC e Turn on ReSource and boot up your computer e Insert RUPS CD into CD drive e Wait for RUPS for Windows 95 98 Setup to appear on screen e Follow installation commands Note If Connection error Please check UPS cable then restart Windows appears on screen check RS232 cable to see whether it is connected securely and properly Other Features 1 15 amp Circuit Breaker Located above the main power switch and recessed for safety If ReSource is overloaded it will trigger this circuit breaker and disconnect power To restore power simply unplug one piece of equipment and push the circuit breaker button in Your ReSource should stay powered If not consult the Amperage ratings on the connected devices and confirm that they do not exceed 15 amps total Usually computers are 1 4 amps fax machines 1 3 and most devices are below 2 You should not have a problem plugging in all your devices 2 10Base T Network Protection Protects against surges coming through the network RJ45 line and damaging your computer ReSource will protect 10Base T lines A 5 ft CAT 5 cable is included 3 Solid State Phone Fax Modem Protection Maximum protection for your RJ11 lin
5. self test which occurs every time the ReSource is powered on by the master switch If this indicator lights you should e Let the ReSource charge for at least 12 hours ReSource must be plugged in and switched on Powered light must be on for the battery to charge e Retest the battery by turning the switch off and then on again The unit will run a 7 second self test to determine the strength of the battery e If the Check Battery light stays on at the completion of the self test the battery must be replaced Contact your Belkin sales representative for information and obtaining a replacement battery Battery Part F5C500 B F5C510 B F5C520 B Surge Protected Indicator This indicator shows the status of your surge protection circuitry This indicator lights when your ReSource has full surge protection If this light is not on the unit has absorbed a power surge and needs to be replaced Please contact Belkin Components for a replacement Wiring OK Indicator This indicator lights when there is a good ground circuit and correct polarity in the building wiring If this light does not come on you should consult an electrician to examine the building wiring Connecting a Belkin ReSource to an improperly grounded outlet will void all Belkin Components warranties Do not attempt to use a 3 prong to 2 prong with ground screw adapter to bypass the ground pin as this will void all Belkin Components warranties as well
6. able to the ReSource and your PC to utilize the shutdown software See Installing Shutdown Software 7 Switch on your ReSource the Powered light will come on It will stay on as long as the switch remains on and power is supplied to the unit For Models F5C510 and F5C520 Communication Port BlockSpace 15 Amp re settable circuit RS232 Serial Port provides extra breaker Recessed for safety Eight 3 line A C For models F5C510 450VA space for large A C Internet Ready surge protected and F5C520 600VA only adapters Solid state outlets phone fax modem gt protection 6 ft phone cord included T l Heavy duty 6 E L foot cord ina aa S 8 Heavy duty impact resistant ABS case PULL TIME SURGE PROTECTION aE y fa S Recessed MAIN A i PUE E d HITAHT BMH UF POWER BUPA power switch helps prevent accidental F ii i i 1 shut off 0 p a 5 amp 5 CHECK BATTERY warns if the battery needs replacement Lies LBS WIRING OK lets you know the outlet ReSource Four battery back up outlets is plugged into is grounded correctly provide running time SURGE PROTECTED indicates the surge protection is functioning properly 10Base T network protection with RJ45 jacks 5 ft CAT 5 cable included Indicators and what they mean 1 Check Battery Indicator This indicator lights wnen ReSource has detected a weak or worn out battery during the
7. e ReSource uses a solid state sidactor which provides maximum protection with twice the clamping speed of an MOV A6 ft phone cord is included 4 Full Time Surge Suppression ReSource provides 1260 Joules of 3 line AC surge protection on all 8 outlets Surge protection is always there even if the main power is switched off 5 Instant Back Up Power Supply 4 outlets are labeled as back up power supply These outlets will receive 120 volts of power when battery is in use Do not plug any devices into these outlets that are not critical when utility power is cut The more devices powered by the battery the shorter the back up time If possible only plug your monitor and PC into these outlets and save the rest for emergencies Troubleshooting ReSource will not stay powered long Battery is weak Recharge battery for 12 hours enough to save and close Too many devices plugged into instant Unplug unnecessary devices from battery back up outlets battery back up outlets Wiring OK light is out Outlet that ReSource is plugged into is Try another outlet in the area if not properly grounded or has polarity results are the same call an crossed electrician to check the wiring of the building ReSource battery back up reacts to The voltage in the building is bad or Plug ReSource into an outlet that undervoltages constantly and beeps there is a heavy load on the outlet does not have a heavy load heavy three to
8. extension cords Any such installation voids the warranty The Belkin Connected Equipment Warranty only protects against damage to properly connected equipment where Belkin Components has determined in its sole discretion that the damage resulted from an occurrence and does not protect against acts of God other than lightning such as flood earthquake war vandalism theft normal use wear and tear erosion depletion obsolescence abuse damage due to low voltage disturbances i e brownouts or sags non authorized program or system equipment modification or alteration This warranty contains the sole warranty of Belkin Components there are no other warranties expressed or except as required by law implied including the implied warranty or condition of quality merchantability or fitness for a particular purpose and such implied warranties if any are limited in duration to the term of this warranty Some states do not allow limitations on how long an implied warranty lasts so the above limitations may not apply to you In no event shall Belkin Components be liable for incidental special direct indirect consequential or multiple damages such as but not limited to lost business or profits arising out of the sale or use of any Belkin Surge Suppressor even if advised of the possibility of such damages This warranty gives you specific legal rights and you may also have other rights which may vary from state to state Some states do not all
9. four times a day ReSource is connected to load means an air conditioner or a refrigerator are on the same circuit as that outlet Have an electrician check to see if your power supply is bad if so a line conditioner may be required ReSource is turned on and it beeps Battery is weak Turn off ReSource for a minimum continuously of 30 minutes to recharge battery ReSource 325VA Battery Runtimes with Common Systems Pentium 200MHz with 17 Monitor Pentium 166MHz with 15 Monitor Pentium 133MHz with 15 Monitor Power Mac Power PC with 17 Monitor Pentium 90MHz with 15 Monitor ReSource 450VA Battery Runtimes with Common Systems Pentium Il 400MHz with 17 Monitor Pentium Il 350MHz with 15 Monitor Pentium Il 333MH2 G3 with 15 Monitor Power Mac Power PC with 17 Monitor Pentium Il 233MHz with 15 Monitor ReSource 600VA Battery Runtimes with Common Systems Pentium Il 400MHz with 17 Monitor Pentium Il 350MHz with 15 Monitor Pentium II 333MH2 G3 with 15 Monitor Power Mac Power PC with 17 Monitor Pentium Il 233MHz with 15 Monitor ReSource Specifications MODEL F5C500 325VA MODEL F5C510 450VA MODEL F5C520 600VA Max Load for Full Time Surge Protection Outlets 125 V 1800W 15A Total 125 V 1800W 15A Total 125 V 1800W 15A Total Max Load utility Power Supplied outlets 4 outlets 125 V 1500W 12A 125 V 1400W
10. nt protection in accordance with the National Electrical Code ANSI NFPA 70 e Servicing of batteries should be performed or supervised by personnel knowledgeable of batteries and the required precautions Keep unauthorized personnel away from batteries BELKIN CONNECTED EQUIPMENT WARRANTY Belkin Components warrants to the original purchaser of any Belkin Surge Suppressor for the life of the product that the surge suppressor shall be free of defects in design assembly material or workmanship and will repair or replace at its option any defective product free of charge Belkin Components will repair or replace at its option any equipment which is damaged by a transient voltage surge spike or lightning strike an Occurrence while properly connected through a Belkin Surge Suppressor to a properly wired AC power line with protective ground For models F5C050 TEL F5C140 F5C240 F5C290 F5C500 F5C550 TEL F5C572 CW F5C572 TEL F5C572 DSS F5C572 TEL EXT F5C594 TEL F5C595 TEL F5C595 TEL2 F5C595 TEL2 EXT F5C695 CW DSS F5C695 TEL F5C695 TEL CLR F5C795 TEL F5C795 100BT F5C895 TEL the telephone line must be properly connected and installed and for model F5C572 AV F5C595 AV F5C695 CW DSS and F5C695 DSS the Coax cable line must also be properly connected and installed as determined by Belkin at its sole discretion This Connected Equipment Warranty is a Limited Warranty subject to the limitations and exclusions set forth herein
11. ow the exclusion or limitation of incidental or consequential damage so the above limitations may not apply to you This warranty is valid only for the original purchaser of the product The original purchaser must complete and return the attached warranty card within 15 days of the date of purchase or the warranty is void All damage claims against the product must be made within 15 days from the date of the occurrence and must be accompanied by a receipt for the damaged equipment or the warranty is void Valid in USA Canada and Bermuda To file a claim against the Belkin Connected Equipment Warranty you must take the following steps 1 Contact Belkin Components at 501 W Walnut St Compton CA 90220 Attn Claims Dept within 15 days of the occurrence Be prepared to provide the following information a The part number of the Belkin Surge Suppressor b The equipment that was connected to the Surge Suppressor at the time of the occurrence c The equipment that was damaged during the occurrence and the extent of the damage d The date of the occurrence e Where you purchased the Surge Suppressor f When you purchased the Surge Suppressor g Copy of the original receipt 3 Your Belkin Customer Service Representative will then instruct you on how to forward your equipment receipt Belkin Surge Suppressor in use during the occurrence and how to proceed with your claim Belkin Components Corporate Headquarters 501 West Walnut Stree
12. retion that it is impractical to ship the damaged equipment to Belkin Components Belkin may designate in its sole discretion an equipment repair facility to inspect and estimate the cost to repair such equipment The cost if any of shipping the equipment to and from such repair facility and of such estimate shall be borne solely by the purchaser Damaged equipment must remain available for inspection until the claim is finalized Whenever claims are settled Belkin Components reserves the right to be subrogated under any existing insurance policies the claimant may have All above warranties are null and void if the Belkin Surge Suppressor in use during the occurrence is not provided to Belkin Components for inspection upon Belkin s request at the sole expense of the purchaser Belkin Components determines that the Belkin Surge Suppressor has been improperly installed altered in any way tampered with Belkin Components determines that the damage did not result from the occurrence or that no occurrence in fact took place the repair or replacement of the damaged equipment is covered under a manufacturer s warranty or Belkin Components determines that the connected equipment was not used under normal operating conditions or in accordance with any labels or instructions All Belkin Surge Suppressors must be plugged directly into the power source and must not be daisychained together in serial fashion with other power strips UPS other surge protectors or
13. t e Compton CA 90220 Phone 310 898 1100 Fax 310 898 1111 www belkin com P72120
14. the battery during utility power outages 4 The ReSource comes with Solid State Phone Fax Modem surge protection Instead of running a connection directly from your Phone Fax Modem to the wall jack you must pass the connection through the protected jacks on your ReSource Connect your phone fax modem line from your wall outlet to the Input jack on ReSource Connect the 6 foot phone cord provided with ReSource into the Output jack and connect the other end of the phone cord to the Phone Fax Modem jack of the device you want to protect f you fail to connect the Phone Fax Modem protection your connected equipment will not be covered by the Connected Equipment Warranty Most modem damage can be prevented if you take the time to connect the Phone Fax Modem protection 5 The ReSource also comes with 10Base T Network protection Instead of running a connection directly from your network wall jack to your PC you must pass the connection through the protected jacks on your ReSource Connect your RJ45 Network line Category 5 cable from your wall outlet to the Input jack on ReSource Connect the 5 foot long CAT 5 patch cable provided into the Output jack on ReSource and connect the other end to the Network connection on the back of your PC f you fail to connect the Network protection when using ReSource with a Network your connected equipment will not be covered by the Connected Equipment Warranty 6 Connect the RS232 c
Download Pdf Manuals
Related Search