GE Profile JKP18 Electric Single Oven
Contents
1. Locked Position D4 Push the hinge locks up against the front frame of the oven cavity to the locked position Notch of Hinge Securely Fitted into Bottom of Hinge Slot Close the oven door Installation Instructions A PRE TEST CHECK LIST Ye ey and any stickers Check to be sure that all wiring is with moving parts secure and not pinched or in contact Remove all protective film if present Vi iY A operation Checklist iy Remove all items from the inside of the oven Check that conduit is securely connected to the junction box Turn on the power to the oven Refer to your Use and Care Manual Verify that the bake and broil units and all cooking functions operate properly Check that the circuit breaker is not tripped or the house fuse is blown See Use amp Care manual for troubleshooting list 12 Check that the bottom trim is installed properly see page 10 Check to be sure the mounting screws are installed and flush with the side trim see page 10 NOTE TO ELECTRICIAN The power leads supplied with this appliance are UL recognized for connections to larger gauge household wiring The insulation of these leads is rated at temperatures much higher than the temperature rating of household wiring The current carrying capacity of a conductor is governed by the wire gauge and also the temperature rating of the insulation around the wire NOTE ALUMINUM WIRING A WARN2. connection to larger gauge household wiring The insulation of these 3 leads is rated at temperatures much higher than the temperature rating of house hold wiring The current carrying capacity of the conductor is governed by the temperature rating of the insulation around the wire rather than the wire gauge alone WARNING Improper connection of aluminum house wiring to copper leads can result in an electrical hazard or fire Use only connectors designed for joining copper to aluminum and follow the manufacturer s recommended procedure closely Turn off the circuit breaker or remove fuses to the oven branch circuit With the oven in front of the cabinet opening on a table or platform connect the flexible conduit to the electrical junction box as shown below You will need to purchase a strain relief clamp to complete the connection of the conduit to the junction box JUNCTION BOX LOCATION PLACE OVEN ON A SUPPORT TO ASSIST IN CONNECTING CONDUIT o ai STRAIN RELIEF CLAMP NOT INCLUDED MUST BE USED AT JUNCTION BOX Continued on Next Page Installation Instructions Electrial Connections con NEW CONSTRUCTION AND FOUR CONDUCTOR BRANCH CIRCUIT CONNECTION e When installing in a new construction or e When installing oven in a mobile home or e When local codes do not permit grounding through neutral a Cut the neutral White lead from the
3. structure Weight on the oven door could cause the oven to tip and result in injury Never allow anyone to climb sit stand or hang on the oven door e Make sure the cabinets and wall cover ings around the oven can withstand the temperatures up to 200 F generated by the oven T CAUTION The electrical power to the oven supply line must be shut off while line connections are being made Failure to do so could result in serious injury or death Electrical Requirements This appliance must be supplied with the proper voltage and frequency and connected to an individual properly grounded branch circuit protected by a circuit breaker or fuse having amperage as noted on rating plate Rating Plate is located on oven side trim We recommend you have the electrical wiring and hookup of your oven connected by a qualified electrician After installation have the electrician show you where your main oven disconnect is located Check with your local utilities for electrical codes which apply in your area Failure to wire your oven according to governing codes could result in a hazardous condition If there are no local codes your range must be wired and fused to meet the requirements of the National Electrical Code ANSI NFPA No 70 Latest Edition You can get a copy by writing National Fire Protection Association Battery March Park Quincy MA 02269 Effective January 1 1996 the National Electrical Code requir
4. Opening Sliding the Oven Into the Drilling the Pilot Holes Opening a Loop do not tie a 36 string around the Note Before drilling the pilot holes conduit before the oven is slid into place make sure the oven is pushed as far This will keep the conduit from falling behind back into the opening as it will go the oven and centered Pull out on string Drill four 1 8 pilot holes through the a 00p while mounting holes top and bottom of the side pushing the oven trim for the four 8 screws provided Drill satenthe GADING eight holes for the Double Oven Lift oven into cabinet cutout using the oven opening as an grip Carefully push against oven front frame Do not push against outside edges The screws must be a minimum of 1 4 from the front of the cutout As you slide the oven back pull the string MOUNTING so that the conduit will lie on top of the oven LOCATIONS in a natural loop When you are sure the conduit is out of the way slide the oven 3 4 way back into the A opening Remove the string by pulling on one end of the loop NOTE Mounting screws must be used Failure to do so could result in the oven falling out of the cabinet causing serious injury b Secure the oven to cabinet with screws provided NOTE If the cabinet is particle board you must use 4 8 x 3 4 particle board screws These may be purchased at any ha
5. crimp Re strip the neutral white lead to expose the proper length of conductor Junction Box Cover b Attach the appliance grounding lead green or bare copper in accordance with local codes If the residence grounding conductor is aluminum see WARNING note c Connect the oven neutral white lead to the branch circuit neutral white or gray in accordance with local codes using wire nut d Connect the oven red lead to the branch circuit red lead and the oven black lead to the branch circuit black lead in accordance with local codes using wire nuts If the residence red black or white leads are aluminum conductors see WARNING note on preceeding page e Install Junction Box Cover OR B4 Three Conductor Branch Circuit Connection When connecting to a 3 conductor branch circuit if local codes permit a Connect the bare oven ground conductor with the crimped neutral white lead to the branch circuit neutral white or gray in color using wire nut Ground Ground and neutral wires Junction Box Cover b Connect the oven red lead to the branch circuit red lead using wire nut c Connect the oven black lead to the branch circuit black lead in accordance with local codes using wire nut If the residence red black or white leads are aluminum conductors see WARNING note on preceeding page d Install Junction Box Cover Installation Instructions Placing the Oven in the
6. ING IMPROPER CONNECTION OF ALUMINUM HOUSE WIRING TO THE COPPER LEADS CAN RESULT IN A SERIOUS PROBLEM Splice copper wires to aluminum wiring using special connectors designed and UL approved for joining copper to aluminum and follow the manufacturer s recommended connector procedure closely NOTE Wire used location and enclosure of splices etc must conform to good wiring practice and local codes Pub No 31 10473 22904053P452
7. Installation 27 Built In Wall Oven JKP15 JKP18 JKP27 JKP45 JKP56 JKSO5 Instru ctions ZEK937 ZEK957 If you have questions call 800 GE CARES or visit our website at www GEAppliances com Before you begin e ATTENTION INSTALLER Read these instructions carefully and completely e IMPORTANT Save these instructions for All electric wall ovens must be hard wired direct wired into an approved junction local inspector s use A box A plug and r tacle is NOT permit e IMPORTANT Observe all governing eae cee erodes ae oe codes and ordinances e NOTE This appliance must be properly e Note to Installer Be sure to leave these grounded instructions with the consumer e OWNER Keep these instructions for future reference Parts Included Materials Needed Wire Nuts a an 3 S Bottom Trim HA i M A Q Single Ovens 4 flat head screws side trim Strain Relief a OX 3 pan head screws bottom trim Clamp for Double Ovens 1 2 conduit SS 8 flat head screws side trim 3 Pan head screws bottom trim 36 of String Tools You Will Need 1 8 Drill Bit amp Phillips Electric or Screwdriver Hand Drill Pub No 31 10473 229C04053P452 1 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS For Your Safety e Be sure your oven is installed properly by a qualified installer or service technician e Be sure the oven is securely installed in a cabinet that is firmly attached to the house
8. dth 27 Recommended Cutout Location from Floor 32 1 2 Cutout Depth 23 1 2 Cutout Width 25 Min 25 1 4 Max Cutout Height 27 5 8 Min 28 1 8 Max NOTE If the cabinet does not have a front frame and the sides are less than 3 4 thick shim both sides equally to establish the cutout width This Oven is not approved for stackable or side by side installation Installation Instructions Cutouts for Double Built In Oven Junction Box Location Cabinet Width 27 Cutout Width _ ui Cabinet Width 27 Allow 7 8 25 1 4 MAK for overlap of oven over side edges of cutout 44 above base anaes bis Recommended Cutout Location from Floor 13 1 4 junction ACinicont Cutout Depth 23 5 8 Min box 2 x 4 or location equivalent Cutout Wdth 25 Min 25 1 4 Max Cutout Height 49 11 16 Min 50 1 8 Max Recommended cutout location Allow a minimum of 20 from floor for clearance to adjacent 13 1 4 corners drawers walls etc when door is open Allow 1 for overtlap of oven top and bottom of cutout NOTE If the cabinet does not have a front frame and the sides tas are less than 3 4 thick shim EQUIVALENT both sides equally to establish the cutout width If the cabinet does not have a solid bottom BRACING i then two braces and runners must be sei ae OVER CENTERLINE installed to support the weight of the oven For double oven
9. es that new but not existing construction utilize a 4 conductor connection to an electric range When installing an electric range in new construction follow the instructions in the section on NEW CONSTRUCTION AND FOUR CONDUCTOR BRANCH CIRCUIT CONNECTION You must use a three wire single phase A C 208Y 120 Volt or 240 120 Volt 60 hertz electrical system If you connect to aluminum wiring properly installed connectors approved for use with aluminum wiring must be used Installation Instructions iY Pre Installation Checklist Door Removal is not a requirement for ALLINSTALLATION INFORMATION ON installation of the product but is an added THE FOLLOWING PAGES IS TO BE convenience USED FOR SINGLE AND DOUBLE OVEN INSTALLATION Vi Open the oven door as far as it will go SY Remove packaging materials Check behind hinges and under Push both hinge Gales false bottom Remove labels on the Vd locks down toward singe Jia Position outside of the door plastic on trims the door frame to sit ANN and panel and all tape around oven the unlocked position This may require a flat blade screwdriver Place hands on both sides of the door close the oven AES Oven Racks door to the removal position this is half Braker Pan ete way between the broil stop and fully closed Open oven door and remove literature pack broiler pan and grid and oven racks Remove Installation Instructions from Vi
10. rdware store 10 Installation Instructions Preparing for the bottom Trim Installation a With oven installed take the bottom trim and center it on the bottom front oer of the cabinet opening Using the trim as S a template mark a Peon the center of neon each slot three total where the mounting holes will be drilled Remove the trim Remove Lower Trim Before Pre Drilling Mounting Holes Drill pilot holes into the center of each template mark Installing the Bottom Trim a Place the bottom trim centered over the pre drilled mounting holes Tape the edges of the trim down to maintain the alignment Trim b Using the three pan head trim screws provided secure the bottom trim to the bottom edge of the cabinet IMPORTANT If this unit is ever removed from the cabinet or the cavity is ever pulled out for service the trim must be removed first or damage to the trim will occur D Replacing the Oven Door The oven door is heavy You may need help lifting the door high enough to slide it into the hinges slots Do not lift the door by the handle Replacing the Oven Door Pick the Oven Door up by placing one hand on each side The door is heavy so you may need help Do not lift the door by the handle Place the notch ofthe Bottom Edge Hinge Arm hinge arm into the Of Slot bottom edge of the hinge slot Hinge Notch D3 Open the oven door as far as it will open Hinge in
11. re ee Set literature pack and read them carefully out until the hinge before you begin aie clear the Be sure to place all literature Use and sols Care Installations etc in a safe place for future reference 3 Continued on following page Installation Instructions IY Pre Installation Checklist Place the oven on a table or platform VY Remove the bottom trim from the even with the cutout opening top of the oven It will be installed at the end of installation The trim is Platform must support 150 Ibs single 275 Ibs double wrapped separately and taped to the top of the unit Bottom Trim Installation Instructions Cutouts for Single Built In Oven ae Junction Box Location Cutout Width Allow 7 8 25 MIN for overlap of 25 1 4 MAX oven over side 22 Min edges of cutout above base 2 x 4 or ig an equivalent 27 5 8 MIN runners 28 1 8 MAX Alternate junction box location Recommended cutout location from floor 32 1 2 Allow a minimum of 20 for clearance to adjacent corners drawers walls etc when door is open Allow 1 for overlap of oven top and bottom of cutout If the cabinets do not have a solid bottom then two braces or runners must be installed to support the weight of the oven For single ovens the runners and braces must support 150 pounds 2 x 4 or Equivalent Runners Cabinet Wi
12. s the runners and braces must support 275 pounds SUITABLE Installation Instructions Cutouts for Single Oven Under Counter Gas or electric cooktops may be installed over this oven See cooktop installation instructions for cutout size See label on top of oven for approved cooktop models Gas or electric connections for gas cooktop must be 240V 208V located in an adjacent Junction Box accessible location Location to the right 25 MIN 25 1 4 MAX aan avenon 2 N a Above Typical 28 1 8 MAX Pee Support coubltertee Platform Height 3 4 Support Platform Required MUST SUPPORT 150 LBS NOTE Stainless Steel models are NOTE This Oven is not approved to be not approved for under the counter installed under a Solid Disk Induction or installation Downdraft Modular Cooktop Installation Instructions Electrical Connections ATTENTION INSTALLER All electric wall ovens must be hard wired direct wired into an approved junction box A plug and receptacle is NOT permitted on these products Do not shorten the flexible conduit The conduit strain Relief Clamp must be securely attached to the junction box and the flexible conduit must be securely attached to the clamp If the flexible conduit will not fit within the clamp do not install the oven until a clamp of the proper size is obtained NOTE TO ELECTRICIAN The 3 power leads supplied with this appliance are UL recognized for
Download Pdf Manuals
Related Search