Infinity KAPPA 50.3CS Car Speaker
Contents
1. USTED TEETER SPEAKER OUTPUTS ToWOOFER pik JO TWEETER TOWARD LISTENER eee ADAPTER RING S 1 SLIDE SCREW UP OR DOWN TO ADJUST Figure 7B Locating wiring connections on the Figure 4 Mounting the 65 3cs ina 165mm i nae g g TWEETER ANGLE 50 3cs woofer Other woofers are wired similarly speaker location TIGHTEN NUT AND WASHER TO LOCK ANGLE SETTINGS SECURELY TIGHTEN THE LARGE HAND NUT Small Lug SPECIFICATIONS 50 3cs Type Crossover Frequency Woofer Speaker Impedance Power Handling Sensitivity Frequency Response Mounting Depth Cut Out Diameter Tweeter Speaker Impedance Power Handling Sensitivity Frequency Response Mounting Depth Cut Out Diameter 5 1 4 2 Way Component 3 5kHz 4 ohms 85W RMS 255W Peak 90dB 2 83V 1m 55Hz 21kHz 2 51mm 4 5 8 118mm 4 ohms 50W RMS 150W Peak 90dB 2 83V 1m 3 5kHz 21kHz 1 3 16 31mm 1 7 8 47mm 60 3cs Type Crossover Frequency Woofer Speaker Impedance Power Handling Sensitivity Frequency Response Mounting Depth Cut Out Diameter Tweeter Speaker Impedance Power Handling Sensitivity Frequency Response Mounting Depth Cut Out Diameter 6 1 2 2 Way Component 3 5kHz 4 ohms 90W RMS 270W Peak 90dB 2 83V 1m 45Hz 21kHz 2 1 16 53mm 5 127mm 4 ohms 50W RMS 150W Peak 90dB 2 83V 1m 3 5kHz 21kHz 1 3 16 31mm 1 7 8 47mm 65 3cs Typ2. In some cars fuel tanks may be located directly beneath the rear deck Before installation make sure there is adequate speaker basket clearance before considering this location ABOUT THE CONTENTS The Kappa Component System includes e 5 1 4 or 6 1 2 or 165mm woofer e Grille and mounting adapter s e 1 tweeter with surface flush I Mount patent no 5 859 917 kits e Crossover network with mounting screws NOTE The supplied crossover network is designed to work with the above listed transducers Do not substitute another crossover network or use other speakers when connecting the system see Figure 7A ae INSTALLATION TIPS e Always wear protective eyewear when using any tools e Turn off all audio components and other electrical devices before you start Disconnect the negative lead from your vehicle s battery e Keep speakers in their package until final installation When moving a speaker always rest it with the cone or dome facing up Never use force to install any speaker e Check clearances on both sides of a planned mounting surface before drilling any holes or installing any screws Remember that the screws can extend behind the surface e At the installation sites locate and make a note of all fuel lines hydraulic brake lines vacuum lines and electrical wiring Use extreme caution when cutting or drilling in and around these areas e Before drilling or cutting holes use a utility knife to
3. Thank you for purchasing Infinity s Kappa Series automotive loudspeaker components We ve organized this manual to make your installation as simple and trouble free as possible Please r adit thoroughly before eding Remember to keep your sales receipt with this manual in a safe place so both are available for future reference INTINILY kappa series 5U0 3cs bU 3cs b5 3cs instructions INSTALLATION WARNINGS AND TIPS ABOUT THESE INSTRUCTIONS Installation of automotive stereo components can require extensive experience with a variety of mechanical and electrical procedures Although these instructions explain how to install Kappa Series Component Systems in a general sense they do not show the exact installation methods for your particular vehicle If you do not feel you have the experience do not attempt the installation yourself but instead ask your authorized Infinity car audio dealer about professional installation options LOUD MUSIC AND HEARING Playing loud music in an automobile can hinder your ability to hear traffic as well as permanently damage your hearing The maximum volume lev els achievable with Infinity speakers combined with high power amplification may exceed safe levels for extended listening We recommend using low volume levels when driving Infinity accepts no liability for hearing loss bodily injury or property damage as a result of use or misuse of this product REAR DECK PRECAUTION
4. e Crossover Frequency Woofer Speaker Impedance Power Handling Sensitivity Frequency Response Mounting Depth Cut Out Diameter Tweeter Speaker Impedance Power Handling Sensitivity Frequency Response Mounting Depth Cut Out Diameter 165mm 2 Way Component 3 5kHz 4 ohms 90W RMS 270W Peak 90dB 2 83V 1m 45Hz 21kHz 2 3 8 61mm 5 1 2 140mm 4 ohms 50W RMS 150W Peak 90dB 2 83V 1m 3 5kHz 21kHz 1 3 16 31mm 1 7 8 47mm DECLARATION OF CONFORMITY CE We Harman Consumer International 2 route de Tours 72500 Chateau du Loir France Infinity Systems Inc 250 Crossways Park Drive Woodbury NY 11797 USA 800 553 3332 FAX 516 682 3523 www infinitysystems com Lutz Uphoff Y Infi nj 2001 Infinity Systems Inc e P N KAPCSOM2 01 Printed 6 01 ae i o H A Harman International Company ee Harman Consumer International i Chateau du Loir France 2 01 declare in own responsibility that the products described in this owner s manual are in compliance with technical standards
5. remove unwanted fabric or vinyl to keep material from snagging in a drill bit or saw e For door installations check the clearance with the windows throughout the range of the window s travel and verify that a mounted speaker will not interfere with the window crank or power window mechanism e If mounting speakers elsewhere check for clearance around rear deck torsion bars glove box or other structural elements e Do not mount speakers where they will get wet e If possible select a mounting site for the crossover network that is near the speakers and provides easy access for connections INSTALLATION Figure 1 Mounting the 50 3cs woofer with the grille Figure 2 Mounting the 60 3cs woofer with the grille Winfiniby INSTALLATION CONNECTIONS Figure 3 Mounting the 60 3cs woofer in a standard Figure 5A Mounting the tweeter using the Figure 6 Mounting the tweeter using the Remove the cover and mount the crossover speaker location A variety of adapter rings are l Mount flush mounting kit l Mount surface mounting kit network Observing proper polarity connect the speakers and amplifier as shown in Figures 7A and 7B When done replace the cover supplied to fit many installation configurations Figure 7A Wiring connections on the crossover network shown with cover on Figure 5B Aiming the tweeter at a desired listening position S o le el 3 pete e Ua a To AMPLIFIER A ii 2
Download Pdf Manuals
Related Search