GE ZDBC240NBS Beverage Cooler
Contents
1. installed freestanding e If installing between frameless cabinets a 1 2 wide filler strip or side panel may be needed on hinge side The filler strip will act as a spacer between the case and adjacent cabinet door swing The width of the opening must include the filler panels NOTE The door should protrude 1 beyond the surrounding cabinets Additional Specifications e A 120 volt 60Hz 15 or 20 amp power supply is required An individual properly grounded branch circuit or circuit breaker is recommended Install a properly grounded 3 prong electrical receptacle recessed into the back wall as shown Electrical must be located on rear wall as shown NOTE GFI ground fault interrupter is not recommended SIDE BY SIDE INSTALLATIONS Increase storage capacity by installing two Monogram beverage centers wine chillers or wine reserves together Or for a complete refreshment center install any two of these units together e A side by side installation requires at least a 47 1 2 wide opening No trim kits required e Products must operate from separate properly grounded receptacles PRODUCT CLEARANCES The wine chiller wine reserve and beverage center is factory set for a 110 door swing When installed in a corner e Allow 4 min clearance on the hinge side for the 90 door swing and to allow racks to slide out e Allow 10 minimum clearance on the hinge side for a full 110 door swing 90 Door Swin2. Installat on Instructions If you have questions call 800 626 2000 or visit our website at www monogram com Wine Chiller Wine Reserve and Beverage Center Design Guide With Installation Instructions Monogram Safety Information BEFORE YOU BEGIN Read these instructions completely and carefully IMPORTAN T Save these instructions for local inspector s use IMPORTAN T Observe all governing codes and ordinances Note to Installer Be sure to leave these instructions with the Consumer Note to Consumer Keep these instructions with your Owner s Manual for future reference WAR N l N G This appliance must be properly grounded See Electrical Supply page 4 AVERTISSEMENT Cet appareil doit tre correctement mis a la terre Consulter lt lt Alimentation lectrique gt gt page 4 If you received a damaged wine chiller wine reserve or beverage center you should immediately contact your dealer or builder Skill Level Installation requires basic mechanical skills Proper installation is the responsibility of the installer Product failure due to improper installation is not covered under the GE Appliance Warranty CONTENTS Design Guide The Installation Space Product Clearances Side by Side Installation Installation Instructions Tools Hardware Grounding the Product Staining Wood Drawer Fronts Step 1 Remove Packaging Step 2 Reverse Door Swing WARNINGS e Us
3. Y GROUNDED The power cord of this appliance is equipped with a three prong grounding plug which mates with a standard three prong grounding wall receptacle to minimize the possibility of electric shock hazard from this appliance Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded Where a standard 2 prong wall outlet is encountered it is your personal responsibility and obligation to have it replaced with a properly grounded 3 prong wall outlet DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE THIRD GROUND PRONG FROM THE POWER CORD DO NOT USE AN ADAPTER PLUG TO CONNECT THE REFRIGERATOR TO A 2 PRONG OUTLET DO NOT USE AN EXTENSION CORD WITH THIS APPLIANCE STAINING WOOD DRAWER FRONTS The drawer fronts are unfinished cherry wood During use oil from hands may accumulate and stain the wood e The drawer fronts may be stained and sealed to match adjacent cabinetry The tinted glass will make the stained wood appear darker A true color match can be seen only when the door is opened e Apply the stain and sealer according to the manufacturer s instructions To avoid unpleasant odor keep the door open to ventilate and allow the stain sealer to dry completely before using the product STEP 1 REMOVE PACKAGING e Remove corner blocks and foam drawer stops e Remove all packing material tape and protective plastic coverings e Remove stainless stee
4. ate behind glass door so that it is visible from the front side e Remove backing from nameplate e Place nameplate onto front side of door matching illustration on the template IMPORTANT Nameplate must be placed on the opposite side of the door handle Note While performing installations described in this book safety glasses or goggles should be worn For Monogram local service in your area call 1 800 444 1845 Note Product improvement is a continuing endeavor at General Electric Therefore materials appearance and specifications are subject to change without notice Pub No 49 60210 4 Monogram Dwg No 197D5129P001 GE Consumer amp Industrial 03 04 JR Louisville KY 40225 Printed in Slovenia 2004 GE Company
5. bottom left side of the door e Install the new supplied bottom case hinge pin and bracket onto bottom left side e Place the door onto the bottom case hinge e Install the supplied left hand top case hinge with the 3 original screws e Select the hinge cover marked with an L e Peel backing off the tape inside the decorative hinge cover e Press and snap the hinge O cover into place e Snap the screw hole cover into place on the opposite side IMPORTANT Check to be sure screws are tight and that the door is straight and does not sag The door should swing freely Install Covers Remove Top Hinge Hinge Door Stop and Cam Riser AN Apply Monogram Nameplate e Install the Monogram nameplate See instructions and template on back cover Install Toekick The toekick has a cutout on the left and right sides Remove the plug on the left side and reinstall on the right side If you choose to install the stainless steel toekick reinstall the plug on the right side of that toekick e Install original screws and spacers or screws and spacers supplied with the stainless steel toekick Install screws through the spacer standoff toekick and into the base as shown Move Fill Plug to Right Side Installation Instructions STEP 3 LEVEL e Use an adjustable wrench to turn the leveling legs and raise or lower the product e Adjust carefully the prod
6. e this appliance only for its intended purpose e Immediately repair or replace electrical service cords that become frayed or damaged e Unplug the unit before cleaning or making repairs e Repairs should be made by a qualified service technician AVERTISSEMENT e Il ne faut utiliser cet appareil que pour l usage pour lequel il a t construit e Il faut r parer ou remplacer imm diatement tout cordon d alimentation lectrique effiloch ou endommag e D brancher le bar ou le r frig rateur a vin avant le nettoyage ou toute intervention e Les r parations doivent tre faites par un technicien qualifi For Monogram local service in your area call 1 800 444 1845 For Monogram service in Canada call 1 888 880 3030 For Monogram Parts and Accessories call 1 800 626 2002 www monogram com Step 3 Leveling Step 4 Connect Power Step 5 Slide Product into Cutout Step 6 Install Nameplate Step 7 Set Temperature Controls Template for Nameplate Back Cover Design Guide THE INSTALLATION SPACE Qutlet 10 172 34 1 2 35 9 Mar El 1 1 2 23 3 4 Min NOTE Handle and handle standoff ass depth is 1 3 4 FAS The cutout depth should be 24 The cutout dimensions shown allow for a full door swing and access to the pull out racks when installed as a built in in standard 24 deep cabinets e The wine chiller wine reserve and beverage center can be
7. g A 10 Minimum to Wall el gt 21 5 8 En A 4 Minimum Ms AAS to Wall e The door swing is reversible on all models If desired change the door swing before installation Choose the location e These products may be closed in on the top and three sides as long as the front is unobstructed for air circulation and proper access to the door e Do not install these products where the temperature will go below 55 F 13 C or above 90 F 32 C Do not install where it will be subject to direct sunlight heat or moisture e These products are not designed to be stacked one over the other Black or Stainless Steel Toekick Options e These products are shipped with a black toekick installed An optional stainless steel toekick is also supplied with each product For shipping purposes the stainless steel toekick is secured to the back of the unit Locate Outlet 10 1 2 1041 2 N e a 14 jp 34 1 2 35 47 1 2 Min Installation Instructions TOOLS REQUIRED e 2 Phillips screwdriver e Adjustable wrench PARTS SUPPLIED e Monogram nameplate e Hardware for changing door swing e Optional stainless steel toekick with screws and spacers e Left and right side hinge covers e Top screw hole cover GROUNDING THE WINE CHILLER WINE RESERVE AND BEVERAGE CENTER IMPORTAN T Please read carefully FOR PERSONAL SAFETY THIS APPLIANCE MUST BE PROPERL
8. l toekick taped to the back of the unit CAUTION Small objects are a choke hazard for children Remove and discard any parts not used MISE EN GARDE z Les petits objets peuvent trangler les enfants Il faut jeter toutes les pi ces qui ne sont pas utilis es Installation Instructions STEP 2 REVERSE DOOR SWING SKIP THIS STEP IF DOOR SWING SUITS THE INSTALLATION Parts Included e Top left case hinge e Bottom left case hinge e Left and right side decorative hinge cover e Decorative hinge screw hole cover e Torx driver bit Tools Required e Phillips screwdriver e Electric drill Remove the door e Flatten the shipping carton to use as a pad e Remove the 2 screws and the toekick Set aside the screws and toekick for final installation e Use the supplied Torx bit and electric drill to remove the 3 screws holding the top case hinge Lift off the hinge Screws will be used to install the new hinge e Lift the door off the bottom case hinge e Remove the bottom case hinge pin and bracket Rotate the door The handle will be on the right side of the door hinges will be installed on the left side of the case e Remove the door stop and cam riser on the original bottom right side of the door e Remove the fill plug on the top right side of the door e Turn the door over and reinstall the fill plug on the new left side Reinstall the door e Install the original door stop and cam riser onto the
9. uct should be level and plumb with cabinetry and should align with adjacent toekick height Turn Right to Lower Turn Left to Raise If you skipped Step 2 e Select the hinge cover marked R or L depending on door swing e Peel backing off the tape inside the decorative hinge cover Press and snap into position e Snap the screw hole cover into place on the opposite side STEP 4 CONNECT POWER e Connect power cord plug to a properly grounded receptacle e Check to make sure power is on by opening the door to see if interior light turns on STEP 5 SLIDE PRODUCT INTO THE CUTOUT e Carefully slide the unit into the opening Be careful not to entangle power cord e Make certain that the door protrudes 1 beyond the surrounding cabinets e Check again to be sure the unit is level STEP 6 INSTALL NAMEPLATE e Follow instructions on the back page for installation of the Monogram nameplate STEP 7 SET TEMPERATURE CONTROLS e The temperature controls are preset Refer to the Owner s Manual for more information Allow 24 hours for temperature to stabilize TEMPLATE FOR NAMEPLATE LOCATION Upper Left Top of Glass Door Upper Right Corner of Corner of Glass if Hinge Top of Badge Glass if Hinge is on Left is on Right lt Door Frame Side DOOR NAMEPLATE LOCATION FRE o To position nameplate e Cut template along dotted line e Hold or tape templ
Download Pdf Manuals
Related Search