ViewSonic PJ755D Multimedia Projector
Contents
1. When the TEMP indicator turns red it indicates the projector has overheated The projector will automati cally shut itself down See page 23 When the LAMP indicator flashes red 0 5 second intervals it indicates a problem with the lamp Turn off the projector and disconnect the power cord from the electrical outlet then contact your local dealer or our service center See page 23 Whenthe LAMP indicator flashes red 1 second intervals it indicates the fan failed Stop using the projec tor and disconnect the power cord from the electrical outlet then contact your local dealer or our service center See page 23 User Controls ViewSonic PJ755D 12 Adjusting the Projected Image Adjusting the Projector Image Height The projector is equipped with an elevator foot for adjusting the image height To raise the image 1 Press the elevator button 1 2 Raise the image to the desired height angle 2 then release the button to lock the elevator foot into position 3 Use 3 to fine tune the display angle To lower the image 1 Press the elevator button 2 Lower the image then release the button to lock the elevator foot into position 3 Use 3 to fine tune the display angle To raise the image 1 Elevator Button Elevator Foot Tilt Addjusting Wheel ViewSonic PJ755D 13 Adjusting the Projector Zoom Focus You may turn the zoom ring to zoom in or out To focus the image rotate the focus r2. S Video to change source to S Video source Video Press Video to change source to Composite Video source ViewSonic PJ755D 16 On Screen Display Menus The Projector has multilingual On Screen Display menus that allow you to make image adjustments and change a variety of settings The projector will automatically detect the source How to operate 1 To open the OSD menu press Menu B on the Remote Control or Control Panel 2 When OSD is displayed use D keys to select any Language Management item in the main menu While making a selection on a par Main image H ticular page press WY key to enter sub menu Menu Brightness IE 3 Use QW keys to select the desired item and adjust the el settings by a D key Frequency E mmm E Phase SS EE so 4 Select the next item to be adjusted in the sub menu and SEN adjust as described above Zoom e a e 5 Press Menu B to confirm and the screen will return to the main menu Sub Menu Setting 6 To exit press Menu B again If you don t press any key the projector will automatically disappear after 30 seconds The OSD menu will close and the projector will automati cally save the new settings Language image N Management Language English CES Choose the multilingual OSD menu Use the 4 or v key to select Deutsch PXD your preferred language Francais H A Press Menu B to finalize the selection ee Espanol Pyccku
3. translucent screen Front Ceiling When you select this function the projector turns the image upside down for ceiling mounted projection Rear Ceiling When you select this function the projector reverses and turns the image upside down at same time You can project from behind a translucent screen with ceiling mounted projection Press OK to adjust Image Language Lamp reminding Lamp hours Lamp reset Eco mode Auto power off min ViewSonic PJ755D 20 anagement Image Image I Language PIP Lamp Reminding Select this function to show or hide the warning message when the lamp replacing reminder message is displayed WE EN The message will show up when the lamp reaches 1500 hours at BEES L 7 a normal mode See Replacing the Lamp for more details Lamp Press OK to adjust Lamp Hours Display the cumulative lamp operating time Source lock Display mode Lamp Reset Reset the lamp life hour after replacing a new lamp ECO Mode Choose On to dim the projector lamp which will lower power consumption and extend the lamp life by up to 130 Choose Off to return normal mode Auto Power Off Sets the interval of power off of the system if there is no signal input In minutes Source Lock When source lock is turned off the projector will search for other signals if the current input signal is lost When source lock is turned on it will search specified connection port Display
4. Mode There are many factory presets optimized for various types of images PC For computer or notebook Movie For home theater Game For game sRGB For PC standard color Dynamic For all these four modes as above and get more contrast and color saturation User Memorize useris settings PIP Image Image Il Language Management PIP PIP Choose On to select on the PIP screen Position Source change Position Choose the PIP screen position on the display screen Swap Source Change Choose the input source of the projector on the PIP screen Swap Choose On to swap main screen and PIP screen each other Note Group 1 S Video Composite Video Component i Group 2 Digital video Component p HDTV PC signals PIP Image can be enabled only when main source is group 1 and PIP source is group 2 OR main source is group 2 and PIP source is group 1 Meaning not for the signals within the same group When swapping the main and PIP displays the smallest screen size of PIP display will be vary depending on different combinations of signal sources for PIP The PIP may not support for some high resolution signals and blue image will be displayed When main source and PIP source come from either DVI I or D SUB15 the two connectors at same time PIP source can not be displayed even one is group 1 and the other is group 2 ViewSonic PJ755D 21 Appendices Troubleshooting If you exp
5. SVGA 800 x 600 op CH ep CH SVGA 800 x 600 72 48 1 72 48 1 SVGA 800 x 600 T5 46 9 75 46 9 SVGA 800 x 600 85 VESA XGA 1024 x 768 43 4 VESA XGA 1024 x 768 53 7 85 53 7 VESA XGA 70 56 5 70 56 5 VESA XGA 85 68 7 68 7 VESA SXGA 1152 x 864 70 VESA SXGA 1152 x 864 75 d 67 5 VESA SXGA 1152 x 864 85 77 1 VESA SXGA 1280 x 1024 60 63 98 VESA SXGA 1280 x 1024 75 79 98 79 98 VESA SXGA 1280 x 1024 85 91 1 91 1 VESA SXGA 1400 x 1500 60 75 60 75 Remark oe o 60 E 63 98 60 63 98 VESA UXGA 1600 x 1200 O CH MAC LC 13 640 x 480 MAC 1113 640 x 480 MAC 16 832 x 624 MAC 19 1024 x 768 MAC 1152 x 870 MAC G4 640 x 480 MAC G4 640 x 480 MAC G4 1024 x 768 i Mac DV 640 x 480 wesch i Mac DV 800 x 600 de Wu i Mac DV 1024 x 768 iMac DV 1152 x 870 Mac DV 1280 x 960 iMac DV 1280 x 1024 ViewSonic PJ755D 26 Customer Support For technical support or product service see the table below or contact your reseller NOTE You will need the product serial number Country Region Web site T Telephone F FAX United States www viewsonic com support T 800 688 6688 service us Qviewsonic com F 909 468 1202 Canada www viewsonic com support T 800 688 6688 service ca viewsonic com F 909 468 1202 United Kingdom www viewsoniceurope com 0800 833 648 service eu viewsoniceurope com 01
6. 293 643910 Europe Middle WWW Viewsoniceurope com Contact your reseller service eu viewsoniceurope com East Baltic coun tries and North Africa Australia and New www viewsonic com au T 61 2 9906 6277 service au viewsonic com Zealand F 61 2 9906 6377 Singapore www viewsonic com sg T 65 273 4018 service sg viewsonic com Malaysia Thailand F 65 273 1566 South Africa www viewsonic com T 886 2 2246 3456 service sd viewsonic com Other countries F 886 2 8242 3668 Hong Kong www hk viewsonic com T 886 2 2246 3456 service hk viewsonic com F 886 2 8242 3668 ViewSonic PJ755D 27 LIMITED WARRANTY ViewSonic Projector What the warranty covers ViewSonic warrants its products to be free from defects in material and workmanship during the warranty period If a product proves to be defective in material or workman ship during the warranty period ViewSonic will at its sole option repair or replace the product with a like product Replacement product or parts may include remanufac tured or refurbished parts or components How long the warranty is effective North and South America Three 3 years warranty for all parts excluding the lamp three 3 years for labor and one I year for the original lamp from the date of the first consumer purchase Europe except Poland Three 3 years warranty for all parts excluding the lamp three 3 years for labor and ninety 90 days for the original lamp from the date of the fi
7. 5 Product Overview Main Unit O ON Oa BOON gt Focus Ring Zoom Ring Zoom Lens Elevator Button Elevator Foot Remote Control Receiver Connection Ports Power Socket Control Panel ViewSonic PJ755D 6 Control Panel ON Oa BOON gt O oO 0 0 Temp Indicator LED Power Indicator LED Lamp Indicator LED Power Standby Menu On Off Source Re sync Four Directional Select Keys Enter Keystone Correction Remote Control Receiver d 5 RE SYNC POWER STANDBY ViewSonic PJ755D 7 Connection Ports 0 Go GOO 0 Q DVI I Input Connector PC Digital and Analog signal HDTV HDCP Component Video Input VGA Connector PC Analog Signal HDTV Component Video Input USB Input Connector RS232 Input Connector Monitor Loop through Output Connector Component Video Input Conntector S Video Input Connector Composite Video Input Connector O ON OO BOON gt Audio Input Connector 10 Audio Output Connector 11 Power Socket 12 Kensington Lock Port ViewSonic PJ755D Remote Control with Mouse Function amp Laser Pointer CONDO O1 P ON Q sd O ND Model No IR2312 MADE IN CHINA IR LEDS Power Sync Keystone Correction Display Format Laser Button Laser Pointer Laser Indicator LED A V Mute F
8. Display Menus EE EE EE EE Ee edited 17 FIOW ee dele EE Honmnsasesnteccr dessein sataceas es ETEA AN 17 Eelere EE ER 17 Image l Computer Mode 4 17 image l Video Mode ioo BE tennis ina SS pes eve vie eee 18 VERE ee AR EE OE RE EE ON D OE N EN 19 7 AUT 0 RD AE E ENE 20 Managemenl ESE EE ha tae E 20 TEE 21 Appendi es EE RENE RO OE Ge EE OLI DDR 22 geiffen e elo Le ss TENENTE 22 Replacing iNe lamp ss REK DE DOE OE GEE Ee dO Maite 25 Compatibility Modes 26 Customer SUDDOTFE E 27 LIMITED WARRANTY E 28 ViewSonic PJ755D Compliance Information Compliance Information for U S A This equipment has been tested and found to comply with the limits for a Class B dig ital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interfer ence to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient of relocate the receiving antenna Increase the separation be
9. K to adjust Press OK to adjust Colourtemp ta D Display format s BS NEM Advance Press OK to adjust Vertical keystone W Horizontal keystone mi Reset Press OK toreset Vertical keystone Press the or to adjust image distortion ver tically and makes a squarer image vl Horizontal keystone Press the or to adjust image distortion horizontally and makes a squarer image Position function is not supported under Position DVI I source Adjust the image position Press OK to adjust Vertical position m Be EI Language Management PIP Image Audio Keystone Press OK to adjust Vertical Position Position Press OK to adjust e CION ems Press the to move the image down olour temp r Display format SEHE BENE EM Et Advance Press OK to adjust D cei Press OKtoreset Horizontal Position ese ress OK to rese Press the to move the image left Horizontal position ram EE so Press the to move the image up Press the to move the image right Color Temp Adjust the color temperature At higher temperature the screen looks colder at lower temperature the screen looks warmer Display Format Use this function to choose your desired aspect ratio EB Windows The input source will be compacted in the center with scaling 4 3 The input source will be scaled to fit the projection screen 16 9 The input source will
10. Portugu s Image I Computer Mode i Brightness Adjust the brightness of the image Language Wy Management Image Il Press the to darken image Brightness Press the gt to lighten the image Contrast Frequency Contrast The contrast controls the degree of difference between the lightest and darkest parts of the picture Adjusting the contrast changes the amount of black and white in the image Press the to decrease the contrast Phase Sharpness Zoom Press the to increase the contrast Sharpness func Frequency tion is not sup Frequency changes the display data frequency to match the fre ported under quency of your computeris graphic card If you experience a vertical computer mode flickering bar use this function to make an adjustment Phase Phase synchronizes the signal timing of the display with the graphic card If you experience an unstable or flickering image use this func tion to correct it ViewSonic PJ755D 17 Sharpness Adjusts the sharpness of the image Press the 9 to decrease the sharpness Press the to increase the sharpness Zoom Press the to magnify an image up to a factor of 16 times on the projection screen Press the to diminish the zoom in image Image I Video Mode Brightness Adjust the brightness of the image Press the to darken image Press the to lighten the image Contras
11. Power LED Message Temp LED Lamp LED Standby State G Error Lamp failed mem Error Fan failed EE Error Over Temp oo Flashing Flashing ViewSonic PJ755D 23 Problem Message Reminders Standby Over Temperature Fan Failed Replacing the lamp ViewSonic PJ755D 24 Replacing the lamp The projector will detect the lamp life itself It will show you a warning message Lamp life exceed When you see this message change the lamp as soon as possible Make sure the projector has been cooled down for at least 30 minutes before changing the lamp Il b Lamp Changing Procedure Switch off the power to the projector by pressing the Power button Allow the projector to cool down at least 30 minutes Disconnect the power cord Push up and Remove the cover 1 Remove the 3 screws from the lamp module 2 Pull out the lamp module 3 To replace the lamp module reverse the previous steps N O OU A M Z Warning Lamp AN compartment is hot Allow it to cool down before changing lamp Z Warning To reduce the risk of personal injury do not drop the lamp module or touch the lamp bulb The bulb may shatter and cause injury if it is dropped ViewSonic PJ755D 25 Compatibility Modes ANALOG DIGITAL V Frequency H Frequency V Frequency H Frequency Hz kHz Hz kHz SVGA 800 x 600 CH o gt CH o gt
12. ViewSonic PJ755D Portable DLP Projector G a amp ViewSonic PJ755D User Guide Guide de l utilisateur Bedienungsanleitung Gu a del usuario Guida dell utente CITE We eM VETE lace Anv ndarhandbok Kayttoopas PYKOBOACTBO NOnb30BaTena BAFA EHF Contents Compliance Information ss RE RE EE ESME WEE Ge stu ke Re ua das Eu de gee de 1 Important Safety Instructions sise 2 POF geilen EE 3 Usad Notice uie ie SG N EG ER De oe EE OG GE EE Si ee eerie 4 miii bio E 4 Ji ge e festo estt Tm 5 ProdtictFeatdi s PEE 5 Package TE 5 PrOdUCUCOVETVIOW me 6 Ma DE se ei ie ie RE ein cadet ge Ee Ee EG RE E 6 CONTO Panel ERR T CONNECCION e 8 Remote Control with Mouse Function amp Laser Pointer 9 installation m 10 Connecting the ProJectOE EE 10 Powering On Off the Projector RL 11 Powerindg ON the PPrOIBC LOL id annee ee Ge Ge EG Ee GE etes 11 Powerinid OF the prole lof 2 x EE EE EE N ED EE eie 12 Adjusting the Projected Image KEER Ee 13 Adjusting the Projector Image Height EE Ee ee ER Ee ee ee ee 13 Adjusting the Projector Zoom FOCUS see EER EE RR EE RR AE ee ee Ee ee ee ee 14 Adjusting Projection Image Size 4 14 leer GC d EE N EE MT 15 Control Panel amp Remote Control LS 15 On Screen
13. al rights and you may also have other rights which vary from state to state Some states do not allow limitations on implied warranties and or do not allow the exclusion of incidental or consequential damages so the above limitations and exclusions may not apply to you Sales outside the U S A and Canada For warranty information and service on ViewSonic products sold outside of the U S A and Canada contact ViewSonic or your local ViewSonic dealer Projector Warranty V3 1 ViewSonic PJ755D 29 CH a 7 z D Lah Bie A SE d gg ViewSonic
14. be scaled to fit the width of the screen Letterbox Letterbox mode zooms a letterboxed image intended for 4 3 display to full screen wide Original Input The letterbox Advance Press OK to adjust the R Red G Green or B Blue for brightness and contrast Reset Press OK to return the display parameters on all menus to their factory default settings ViewSonic PJ755D 19 Audio Volume Press the to decrease the volume Press the to increase the volume Treble The treble setting controls the higher frequencies of your audio source Language Management Image Image Il Volume Treble Bass Stereo Mono Mute Press the to decrease the treble Press the gt to increase the treble Bass The Bass setting controls the lower frequencies of your audio source Press the 4 to decrease the bass Press the gt to increase the bass Stereo Mono Mono d Mono sound effect Stereo hd Stereo sound effect Mute Choose the left icon to turn mute on Choose the right icon to turn mute off Management Image Language Menu Location Menu location Choose the menu location on the display screen Projection IS Eie EI Lamp Projection Source lock IBS Front Desktop NNNM MB HE Lamp The factory default setting Rear Desktop When you select this function the projector reverses the image so you can project behind a
15. ds logo and OnView are registered trademarks of ViewSonic Corporation VESA and SVGA are registered trademarks of the Video Electronics Standards Asso ciation DPMS and DDC are trademarks of VESA PS 2 VGA and XGA are registered trademarks of International Business Machines Corporation Disclaimer ViewSonic Corporation shall not be liable for technical or editorial errors or omissions contained herein nor for incidental or consequential damages resulting from furnishing this material or the performance or use of this product In the interest of continuing product improvement ViewSonic Corporation reserves the right to change product specifications without notice Information in this document may change without notice No part of this document may be copied reproduced or transmitted by any means for any purpose without prior written permission from ViewSonic Corporation Electronic Warranty Registration To meet your future needs and to receive any additional product information as it becomes available please register your projector s warranty on the Internet at http www viewsonic com For Your Records Product Name ViewSonic PJ755D Model Number VS10412 Document Number A CD PJ755D Serial Number Purchase Date ViewSonic PJ755D 3 Usage Notice Precautions Follow all warnings precautions and maintenance as recommended in this users guide to maximize the life of your unit Warning Do not look into the
16. erience trouble with the projector refer to the following information If the problem persists please con tact your local reseller or service center Problem No image appears on screen Ensure all the cables and power connections are correctly and securely connected as described in the Installation section Ensure the pins of connectors are not crooked or broken Check if the projection lamp has been securely installed Please refer to the Replacing the lamp section Make sure you have removed the lens cap and the projector is switched on Press A V Mute button to maker sure the image has not been turned off temporarily Problem Partial scrolling or incorrectly displayed image Press the Sync button on the Remote Control or Press the Re Sync button on the Control Panel If you use a PC If the resolution of your computer is higher than 1024 x 768 Follow the steps outlined below to reset the resolution For Windows 3 x 1 In the Windows Program Manager click the Windows Setup icon in the Main group 2 Verify that your display resolution setting is less than or equal to 1024 x 768 For Windows 95 98 2000 XP 1 Open My Computer icon the Control Panel folder and then double click on the Display icon 2 Select the Setting tab 3 In the Desktop Area you will find the resolution setting Verify that the resolution setting is less than or equal to 1024 x 768 reso
17. he other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet con sult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the unit Be sure that the power outlet is located near the unit so that it is easily accessible Only use attachments accessories specified by the manufacturer Use only with the cart stand tripod bracket or table specified by the manufac turer or sold with the unit When a cart is used use caution when moving the cart unit combination to avoid injury from tip over Unplug this unit when unused for long periods of time Refer all servicing to qualified service personnel Servicing is required when the unit has been damaged in any way such as power supply cord or plug is dam aged liquid has been spilled or objects have fallen into the unit the unit has been exposed to rain or moisture does not operate normally or has been dropped ViewSonic PJ755D 2 Copyright ViewSonic Corporation 2004 All rights reserved Apple Mac and ADB registered trademarks of Apple Computer Inc Microsoft Windows Windows NT and the Windows logo are registered trademarks of Microsoft Corporation in the United States and other countries ViewSonic the three bir
18. he screen image Display Mode Select the display mode from PC Movie Game sRGB Dynamic and User Mouse Mouse Right Click Mouse Left Click These functions are the same as a mouse of PC or Mac Page Up Gi Use this button to page up Page Down EI Remark this is com Use this button to page down puter mode only And Page Scrolling these functions are only available when the projec tor is connected to a com Zoom In EN Zoom Out 9 puter via an USB cable Press Ei or 9 button to zoom the lens in or zoom out Control the scroll bar to move the screen up or down Four Directional Select Keys Use AVE D to select items or make adjustments to your selection ok Confirm your selection of items Source Lock Select auto detection all connector ports or lock current connector port Menu Press Menu to launch the on screen display menu To exit OSD press Menu again VGA Press VGA to change source to VGA In connector This connector supports Analog RGB YPbPr 480p 576p 720p 1080i YCbCr 4801 5761 and RGBsync DVI I Press DVI I to change source to DVI I connector This connector supports Digital RGB Analog RGB YPbPr 480p 576p 720p 1080i YCbCr 480i 576i and HDCP signal Component Press Component to change source to component connector This connector supports YPbPr 480p 576p 720p 1080i and YCbCr 4801 5761 S Video Press
19. ing until the image is clear The projector will focus at distances from 3 9 to 32 8 feet 1 2 to 10 0 meters Zoom Ring Focus Ring Adjusting Projection Image Size 246 1 625 0cm 196 9 500 0cm 172 2 437 5cm 205 1 520 8cm 123 0 312 5cm 164 0 416 70m 443 5 gt 73 8 187 5cm 364 6cm 102 5 29 5 75 0cm 260 4cm ei gr 156 3cm 248 62 5cm 3 94 1 2m IS 9 84 3 0m 3 22 97 7 0m 1 2m 3 0m 1640 5 0m 22 97 7 0m 26 25 8 0m 32 81 10 0m Screen x 29 5 75 0cm 73 8 187 5cm 123 0 312 5cm 172 2 437 5cm 196 9 500 0cm 246 1 625 0cm Diagonal 24 6 62 5cm 61 5 156 3cm 102 5 260 4cm 143 5 364 6cm 164 0 416 7cm 205 1 520 8cm 23 60 x 17 70 59 04 x 44 28 98 40 x 73 80 137 76 x 103 32 157 52 x 118 14 196 88 x 147 66 Screen PROCU 60 0 x 45 0cm 150 0 x 112 5cm 250 0 x 187 5cm 350 0 x 262 5cm 400 0 x 300 0cm 500 0 x 375 0cm Size Min WxH 19 68 x 14 76 49 20 x 36 90 82 00 x 61 50 114 80 x 86 10 131 20 x 98 40 164 08 x 123 06 50 0 x 37 5cm 125 0 x 93 8cm 208 3 x 156 2cm 291 7 x 218 8cm 333 4 x 250 0cm 416 6 x 312 5cm Distance 3 94 1 2m 9 84 3 0m 16 40 5 0m 22 97 7 0m 26 25 8 0m 32 81 10 0m This graph is for user 5 reference only ViewSonic PJ755D 14 User Controls Control Panel amp Rem
20. lution If the projector is still not projecting the whole image you will also need to change the monitor display you are using Refer to the following steps 4 Follow the above steps 1 2 Click on the Advanced Properties button 5 Select the Change button under the Monitor tab 6 Click on Show all devices Then select Standard monitor types under the Manufacturers box choose the resolution mode you need under the Models box 7 Verify that the resolution setting of the monitor display is less than or equal to 1024 x 768 If you are using a Notebook PC 1 You are required to implement the above steps of resolution setting of the computer first 2 Switch the Notebook PC display to the external display only or CRT only mode If you experience difficulty in changing resolutions or your monitor freezes restart all the equipment and the projector Problem The screen of the Notebook or Power Book computer is not displaying your presentation If you are using a Notebook PC Some Notebook PCs may deactivate their screens when a second display device is in use Refer to your computer s documentation for information on how to reactivate the monitor display If you are using an Apple PowerBook In Control Panels open the PowerBook Display to select Video Mirroring On ViewSonic PJ755D 22 Problem Image is unstable or flickering Use Phase to correct it Refer to page 17 Change the mo
21. nitor color setting from your computer Problem Image has vertical flickering bar Use Frequency to make an adjustment Refer to page 17 Check and reconfigure the display mode of your graphic card to make it compatible with the product Refer to page 26 Problem Image is out of focus Adjusts the Focus Ring on the projector lens Refer to page 14 Make Sure the projection screen is between the required distance 3 9 to 32 8 feet 1 2 to 10 0 meters from the projector Problem The image is stretched when displaying 16 9 DVD The projector automatically detects 16 9 DVD and adjusts the aspect ratio by digitizing to full screen with 4 3 default setting If the image is still stretched you will also need to adjust the aspect ratio by referring to the following Please select 4 3 aspect ratio type on your DVD player if you are playing a 16 9 DVD If you can t select 4 3 aspect ratio type on your DVD player please select 4 3 aspect ratio in the on screen menu Problem Image is reversed Select Settings from the OSD and adjust the projection direction See page 20 Problem Lamp burns out or makes a popping sound When the lamp reaches its end of life it will burn out and may make a loud popping sound If this happens the projector will not turn on until the lamp module has been replaced To replace the lamp follow the procedures in the Replacing the Lamp See page 25 Problem LED lighting message
22. ote Control There are two ways for you to control the functions Remote Control and Control Panel Control Panel Remote Control Using the Control Panel Power Standby o Referto the Power On Off the Projector section on pages 11 12 Source Press Source to choose RGB Component p Component i S Video Composite Video and HDTV Sources Menu Press Menu to launch the on screen display OSD menu To exit OSD press Menu again Keystone AA U Adjusts image distortion caused by tilting the projector 16 degrees Four Directional Select Keys Use 4 to select items or make adjustments to your selection Enter m Confirm your selection of items Re Syne gt Only Analog RGB signal valid Automatically synchronizes the projector to the input source ViewSonic PJ755D 15 Using the Remote Control Power Refer to the Power On Off the Projector section on pages11 12 Sync Automatically synchronizes the projector to the input source Keystone Adjusts image distortion caused by the tilting of the projector 16 degrees Display Format Display the Display Format section of the onscreen display menu to select the desired aspect ratio Laser Button Q Aim the remote at the viewing screen press and hold this button to activate the laser pointer A V Mute Momentarily turns off the audio and video Model No IR2312 Freeze Press Freeze to pause t
23. projector s lens when the lamp is on The bright light may hurt your eyes Warning To reduce the risk of fire or electric shock do not expose this product to rain or moisture Warning Please do not open or disassemble the product as this may cause electric shock Warning When changing the lamp please allow unit to cool down and follow all changing instruc tions Warning This product will detect the life of the lamp itself Please be sure to change the lamp when it shows warning messages Warning Reset the Reset Lamp Hour function from the On Screen Display info menu after replac ing the lamp module refer to page 21 Warning When switching the projector off please ensure the projector completes its cooling cycle before disconnecting power Warning Turn on the projector first and then the signal sources Warning Do not use lens cap when projector is in operation Warning When the lamp reaches the end of its life it will burn out and may make a loud popping sound If this happens the projector will not turn back on until the lamp module has been replaced To replace the lamp follow the procedures listed under Replacing the Lamp Do Turn off the product before cleaning Use a soft cloth moistened with mild detergent to clean the display housing Disconnect the power plug from AC outlet if the product is not being used for a long period of time Don t Block the slots and openings on the unit
24. provided for ventilation Use abrasive cleaners waxes or solvents to clean the unit Useunder the following conditions In extremely hot cold or humid environments In areas susceptible to excessive dust and dirt Near any appliance that generates a strong magnetic field Place in direct sunlight ViewSonic PJ755D 4 Introduction Product Features This product is an XGA single chip 0 7 DLP projector Outstanding features include True XGA 1024 x 768 addressable pixels Single chip DLPTM technology NTSC NTSC4 43 PAL PAL M PAL N SECAM and HDTV compatible 480i p 576i p 720p 1080i HDCP compliant High tech DVI I connection for digital and analog video connectivity Full function remote with mouse control and laser pointer User friendly multilingual on screen display menu Advanced digital keystone correction and high quality full screen image re scaling User friendly control panel Picture In Picture dual image UXGA SXGA compression and VGA SVGA re sizing Mac compatible Package Overview This projector comes with all the items shown below Check to make sure your unit is complete Contact your dealer immediately if anything is missing Gee cx Ces PJ755D Projector Power Cord 1 8m VGA Cable 1 8m Composite Video Cable DVI to D Sub RCA Component S Video Cable 1 8m Remote Control with Cable1 8m Cable YPbPr 1 8m Mouse Function amp Laser Pointer m 3 SS ViewSonic PJ755D
25. r LED will turn red Turn on the lamp by pressing Power Standby button on the control panel 1 The start up screen will display for 30 seconds and the Power LED will flash green When the startup screen disappears the Power LED will turn green Turn on your source computer notebook video player etc The projector will detect your source automatically If you connect multiple sources at the same time use the Source button on the control panel to switch Power Standby Turn on the pro jector first and then the signal sources ViewSonic PJ755D 11 D off the projector Press the Power Standby button to turn off the projector lamp you will see a message Wait 2 minutes before you can switch on again on the on screen display 2 Press the Power Standby button again to confirm 3 Otherwise the message will disappear after 10 seconds 4 The cooling fans continue to operate for about 120 seconds for cooling cycle and the Power LED will turn red When the light stops flashing the projector has entered standby mode 5 If you wish to turn the projector back on you must wait until the projector has completed the cooling cycle and has entered standby mode Once in standby mode simply press Power Standby button to restart the projector 6 Disconnect the power cord from the electrical outlet and the projector 7 Do not turn on the projector immediately following a power off procedure
26. reeze Display Mode Mouse Mouse Right Click 9 A Display format OOOO d Be v P de b gd e ef N oo Seeeeegf E Cd OGO elei ai DOOP DDO 14 Mouse Left Click 15 Page Up Page Down 16 Page Scrolling 17 Zoom In Zoom Out 18 Four Directional Select Keys 19 OK Enter 20 Source Lock 21 Menu 22 VGA Source 23 DVI I Source 24 Component Video Source 25 S Video Source 26 Composite Video Source ViewSonic PJ755D 9 Installation Connecting the Projector OO N Oo Om BOON gt N Ug rt d oa TE Kr Ll I k o mi Digital Tuner Output yim mum Quum S Video Output Video Output Power Cord VGA Cable Composite Video Cable DVI to D Sub Cable S Video Cable RCA Component Cable for YPbPr D Sub to RCA Cable for HDTV Component Optional Accessory DVI to DVI Cable Optional Accessory RS232 Cable Optional Accessory To ensure the projector works well with your computer please set the display mode of your graphic card less than or equal to 1024 X 768 resolution Make sure the timing of the display mode is compatible with the pro jector Refer to the Compatibility Modes section on page 26 ViewSonic PJ755D 10 Powering On Off the Projector Powering On the Projector 1 2 3 Remove the lens cap Ensure that the power cord and signal cable are securely connected The Powe
27. rst consumer purchase Poland Two 2 years warranty for all parts excluding the lamp two 2 years for labor and ninety 90 days for the original lamp from the date of the first consumer purchase Other regions or countries Please check with your local dealer or local ViewSonic office for the warranty information Lamp warranty subject to terms and conditions verification and approval Applies to manufacturer s installed lamp only All accessory lamps purchased separately are warranted for 90 days Who the warranty protects This warranty is valid only for the first consumer purchaser What the warranty does not cover 1 Any product on which the serial number has been defaced modified or removed 2 Damage deterioration or malfunction resulting from a Accident misuse neglect fire water lightning or other acts of nature unautho rized product modification or failure to follow instructions supplied with the prod uct b Repair or attempted repair by anyone not authorized by ViewSonic c Any damage of the product due to shipment d Removal or installation of the product e Causes external to the product such as electric power fluctuations or failure f Use of supplies or parts not meeting ViewSonic s specifications g Normal wear and tear h Any other cause which does not relate to a product defect 3 Removal installation and set up service charges How to get service 1 For information about receiving service
28. t The contrast controls the degree of difference between the lightest and darkest parts of the picture Adjusting the contrast changes the amount of black and white in the image Press the to decrease the contrast Press the to increase the contrast Colour saturation Adjusts a video image from black and white to fully saturated color Press the 9 to decrease the amount of color in the image Press the to increase the amount of color in the image Tint Adjusts the color balance of red and green Press the to increase the amount of green in the image Press the gt to increase the amount of red in the image Sharpness Adjusts the sharpness of the image Press the 9 to decrease the sharpness Press the to increase the sharpness Zoom Language Brightness Contrast Color Tint Sharpness Zoom zk D Management Image Il T See D IE BH ee mm N Colour function is not supported under YPbPr source Sharpness function is not supported under YPbPr and YCbCr source Press the 9 to magnify an image up to a factor of 16 times on the projection screen Press the to diminish the zoom in image ViewSonic PJ755D 18 Image ll Language Management PIP Image Audio Keystone Keystone Correction Keystone Press OK to adjust Adjust image distortion caused by tilting projector 16 degrees Position Press O
29. tween the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Compliance Information for Canada Notice This class B digital apparatus complies with Canada ICES 003 AVIS Cet appeil numerique de la Classe B conforme a la norme NMB 003 du Can ada Compliance Information for European Countries CE Conformity The device complies with the requirements of the EEC directive 89 336 3 EEC as amended by 92 31 EEC and 93 68 EEC Art 5 with regard to Electromagnetic compatibility and 73 23 EEC as amended by 93 68 EEC Art 13 with regard to Safety User Information for all Countries Notice Use the cables which are included with the projector or specified ViewSonic PJ755D 1 Important Safety Instructions pU NM AM ex 10 11 12 13 14 Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this unit near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufac turer s instructions Do not install near any heat sources such as radiators heat registers stoves or other devices including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polar ized plug has two blades with one wider than t
30. under warranty contact ViewSonic Cus tomer Support You will need to provide your product s serial number 2 o obtain warranted service you will be required to provide a the original dated sales slip b your name c your address d a description of the problem and e the serial number of the product 3 Take or ship the product freight prepaid in the original container to an authorized ViewSonic service center or ViewSonic 4 For additional information or the name of the nearest ViewSonic service center contact ViewSonic ViewSonic PJ755D 26 Limitation of implied warranties THERE ARE NO WARRANTIES EXPRESS OR IMPLIED WHICH EXTEND BEYOND THE DESCRIPTION CONTAINED HEREIN INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PUR POSE Exclusion of damages VIEWSONIC S LIABILITY IS LIMITED TO THE COST OF REPAIR OR REPLACE MENT OF THE PRODUCT VIEWSONIC SHALL NOT BE LIABLE FOR 1 DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECTS IN THE PROD UCT DAMAGES BASED UPON INCONVENIENCE LOSS OF USE OF THE PRODUCT LOSS OF TIME LOSS OF PROFITS LOSS OF BUSINESS OPPOR TUNITY LOSS OF GOODWILL INTERFERENCE WITH BUSINESS RELATION SHIPS OR OTHER COMMERCIAL LOSS EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES 2 ANY OTHER DAMAGES WHETHER INCIDENTAL CONSEQUENTIAL OR OTH ERWISE 3 ANY CLAIM AGAINST THE CUSTOMER BY ANY OTHER PARTY Effect of state law This warranty gives you specific leg
Download Pdf Manuals
Related Search