GE Monogram ZDI15C Automatic Icemaker
Contents
1. OPTIONAL ACCESSORIES ZIP75WW White and ZIP75BB Black For the ZPK1 Drain Pump Kit For use when a floor drain is installation of a trimless 3 4 thick custom panel on not available white and black models not for stainless steel models A custom handle of your choice may be installed onto the 3 4 panel See installation instructions on pages 9 and 10 TOOLS AND MATERIALS REQUIRED e 1 4 socket e 3 4 adjustable wrench e Level e GE SmartConnect Refrigerator Tubing Kit or 1 4 0 D copper tubing of sufficient length to reach the installation Installation Instructions ADVANCE PLANNING CAUTION Due to excessive weight TWO PEOPLE ARE REQUIRED TO MOVE AND INSTALL THIS ICE MACHINE MISE EN GARDE A cause de son poids leve IL FAUT DEUX PERSONNES POUR DEPLACER ET INSTALLER CE DISTRIBUTEUR DE GLACE Choose the location e The ice machine must be installed in an area protected from elements such as wind rain water spray or drip The area should be ventilated with temperatures above 55 F 13 C and below 110 F 43 C Best results are obtained between 70 F 21 C and 90 F 32 C e The ice machine may be closed in on the top and three sides as long as the front is unobstructed for air circulation and proper operation Installation should be such that the ice machine can be moved forward for servicing if necessary The bottom grille on the front must be unobstructed to provide pro2. adjustments may be necessary to install the ice machine below a countertop and may be accomplished by adjusting both the front and rear leveling legs Rais N Di Lower To adjust the height e With one person holding the ice machine carefully tilt the machine to access the leveling legs e Use an adjustable wrench to turn the legs Turn legs right to lower turn left to raise the machine e Check top and side with a spirit level Continue adjusting legs until the ice machine is level and stable Installation Instructions WATER SUPPLY e A cold water supply is required for icemaker operation The water pressure must be between 20 and 120 p s i Water Supply Should Enter From Back Wall In Shaded Area e Route GE SmartConnect Kit or 1 4 0 D copper tubing between house cold water line and the water connection location e The water line should be long enough to extend to the back of the ice machine Allow enough to accommodate moving unit forward for service NOTE The only GE approved plastic tubing is supplied in the GE SmartConnect Refrigerator Tubing kits Do not use any other plastic water supply line because the line is under pressure at all times Other types of plastic may crack or rupture with age and cause water damage to your home GE SmartConnect Refrigerator Tubing Kits are available in the following lengths 2 0 6m WX08X10002 6 1 8m WX08
3. Code ANSI NFPA 70 1990 or latest edition For Monogram local service in your area call 1 800 444 1845 For Monogram Service in Canada call 1 888 880 3030 For Monogram Parts and Accessories call 1 800 626 2002 CONTENTS Design Information Models Available Cutout amp Product Dimensions Optional Accessories Tools and Materials Required Installation Advance Planning Power Supply Remove Packaging Adjust Height of Ice Machine Water Supply Connect the Drain Connect Water Supply Reverse Door Swing Accessories ZIP75WW ZIP75BB Kit for 3 4 thick panels Design Information MODELS AVAILABLE ZD115 ZDIS15 The ice machine may be installed below a countertop Available in black white and stainless steel or used free standing CUTOUT amp PRODUCT DIMENSIONS Cutout dimensions shown allow for a full door swing When installing a 3 4 thick custom door panel additional clearances at the sides may be required Frameless Cabinets e If installing between frameless cabinets a 1 2 filler strip or side panel may be required on the hinge side The filler strip will act as a spacer between the door case and adjacent cabinet and will prevent interference with icemaker door swing The width of the opening must include filler or side panel thickness NOTE The addition of a 3 4 thick front panel will result in a front to back depth of 24 1 16 23 5 16 to Door Front oS as
4. Installation Instructions If you have questions call 800 626 2000 or visit our website at www monogram com Automatic Icemaker ZDI15 ZDIS15 Design Guide with Installation Instructions Monogram Installation Instructions BEFORE YOU BEGIN Read these instructions completely and carefully e IMPORTANT Save these instructions for local inspector s use e IMPORTANT observe all governing codes and ordinances Note to Installer Be sure to leave these instructions with the Consumer e Note to Consumer Keep these instructions with your Owner s Manual for future reference WARNING This appliance must be properly grounded See Power Supply page 4 AVERTISSEMENT Cet appareil doit tre correctement mis a la terre Consulter Alimentation lectrique page 4 If you received a damaged ice machine you should immediately contact your dealer or builder Proper installation is the responsibility of the installer Product failure due to improper installation is not covered under the GE Appliance Warranty See the Owner s Manual for warranty information e Use this appliance only for its intended purpose Check with local utilities for electrical codes that apply in your area Local codes vary Installation electrical connections and grounding must comply with applicable codes In the absence of local codes the ice machine should be installed in accordance with National Electrical
5. X10006 15 4 6 m WX08X10015 25 7 6 m WX08X10025 Shut off the main water supply Turn on the nearest faucet long enough to clear the line of water Install a shut off valve between the ice machine water valve and cold water pipe in a basement or cabinet The installation of an easily accessible shut off valve in the water line is required NOTE It is best to install the valve into a vertical water pipe If you install the valve into a horizontal water pipe make the connection at the top or side rather than at the bottom to avoid drawing off any sediment from the water pipe e Turn on the main water supply and flush debris from the line Run about a quart of water through the tubing into a bucket Shut off water supply at the shut off valve WATER SUPPLY cont NOTE Saddle type shut off valves are included in many water supply kits but are not recommended for this application NOTE Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to Saddle valves are illegal and use is not permitted in Massachusetts Consult with your licensed plumber e Install optional water filter in the water line near the ice machine A water filter is recommended in areas where water supply contains sand or particles Installation instructions are packed with the filter CONNECT THE DRAIN This ice machine is equipped with a gravity drain to prevent water from flowing back into the ice machine storage bin and po
6. chine STEP 4 SECURE CUSTOM HANDLE TO CUSTOM PANEL SKIP THIS STEP IF YOU ARE USING THE SUPPLIED HANDLE A custom handle can be installed onto the 3 4 thick panel replacing the supplied handle e The custom handle can be installed at the top or side of the panel e Drill pilot holes through the front of the custom panel to match the chosen handle e Secure the handle to the panel with flat head wood screws e Replace original handle screws in the top of the door frame 10 STEP 5 SECURE SIDE TRIM PIECES TO CUSTOM PANEL e Lay the custom panel appearance side down on a clean surface e Align top and bottom side trim to the custom panel sides e Tape the side trim pieces to the back of the custom panel e Place the panel with trim against the door to be sure that trim and panel fits the door side to side and top to bottom Adjust as needed e Mark screw locations and remove trim Drill pilot holes e Install side trim to the back side of the custom panel with screws not supplied Use flat head wood screws approximately 1 2 long STEP 6 INSTALL ASSEMBLED PANEL ONTO THE ICE MACHINE e Install panel to ice machine with supplied screws 4 on each side STEP 7 INSTALL SUPPLIED DOOR HANDLE IF USED e Install the new supplied handle with original screws Notes Pub No 49 60016 3 Part No 197D2522P001 2217279 Rev 1 02 04 JR Printed in the United States NOTE While perfor
7. dcaps e Remove the screws and endcaps from the door top and bottom e Place the top endcap onto the bottom of the opposite side of the door with the long flat side facing the door front e Place the bottom endcap onto the top of the opposite side of the door with the long flat side facing the door front e Set the door aside Installation Instructions REVERSE THE DOOR SWING cont Reverse the hinges e Using a flat putty knife remove the screw hole plugs opposite the door hinges top and bottom Set aside e Remove the two screws holding top hinge e Turn the hinge upside down with the hinge pin pointing up Reinstall the hinge on the opposite side at the bottom of the door e Remove the bottom hinge Turn the hinge upside down and install on the opposite side at the top e Push screw hole plug buttons supplied into the original screw holes e Remove the top hinge pin e Place plastic hinge sleeve on the bottom hinge and position the door onto the pin e Place plastic hinge sleeve in the top hinge hole on the door Align the door on the bottom hinge and replace top hinge pin e Reinstall handle with original screws Top Hinge Hinge Pin Hinge Sleeve Door Stop Bottom Hinge Pugs eae Hon Head Hinge Screw Hinge Sleeve Door Stop Top Hinge Bottom Hinge REVERSE THE DOOR SWING cont To reverse the door catch e Remove the plastic screws from the opposite side of t
8. he icemaker case and the adjacent cabinet and will prevent interference with the icemaker door swing The width of the cutout opening must include the additional width of the filler panels This kit contains a new handle and 2 side mounting brackets to support a trimless custom door panel up to 3 4 thick A custom handle may replace the supplied handle IMPORTANT e Cut edges of the custom door panel will be seen and must be finished for best appearance The back side of the panel should be finished a minimum of 1 2 on all sides e The custom panel both raised and flat design should be constructed in the same manner as typical cabinet doors e Order the custom panel from the cabinet manufacturer Be sure to provide the exact dimensions so that the panel is constructed accurately Left Trim aera sa geen N pe _f Pe o Custom Panel S N Right Trim Installation Instructions for ZIP75WW ZIP75BB Kit STEP 1 DISCONNECT POWER TO THE ICE MACHINE STEP 2 REMOVE HANDLE AND NAMEPLATE e Remove the door handle by removing the two top mounting screws Set screws aside Discard handle e The Monogram nameplate is held in place with adhesive Remove the nameplate STEP 3 MARK MOUNTING SCREW LOCATIONS e Align and hold the side trim pieces against the ice machine door and mark screw locations on the sides e Drill 1 8 pilot holes into the door sides of the ice ma
9. he door e Remove the metal screws from the magnetic door catch and reinstall on the Roverse opposite side of the door 7 Y Position e Install the plastic screw into place on the opposite side of the door Installation Instructions for ZIP75WW ZIP75BB Kit BEFORE YOU BEGIN Read these instructions completely and carefully e IMPORTANT Save these instructions for local inspector s use IMPORTANT observe all governing codes and ordinances e Note to Installer Be sure to leave these instructions with the Consumer e Note to Consumer Keep these instructions with your Owner s Manual for future reference co WARNING X To prevent electric shock disconnect electrical power supply to ice machine before installing front panel Do not operate ice machine while installing panel AVERTISSEMENT Pour viter les chocs lectriques il faut debrancher l alimentation du distibuteur de glace avant d installer le panneau avant Le distributeur de glace ne doit pas tre en marche pendant l installation du panneau avant Kit Contents e 2 side trim pieces e 8 side trim screws e Door handle Tools and Materials Required e 8 flat head wood screws 1 2 long e Drill and 1 8 bit e Safety glasses e Tape e Custom panel NOTE If installing a 3 4 trimless custom panel a 3 4 wide filler strip or side panel may be required The filler strip will act as a spacer between t
10. ming installations described in this book safety glasses or goggles should be worn For Monogram local service in your area call 1 800 444 1845 NOTE Product improvement is a continuing endeavor at General Electric Therefore materials appearance and specifications are subject to change without notice Monogram GE Consumer amp Industrial Louisville KY 40225 2004 GE Company
11. or time delay fuse Electrical Supply Should Enter From Back Wall In Shaded Area e A properly grounded 3 prong receptacle should be located within reach of the ice machine s 66 long power cord For a built in installation locate the receptacle in the shaded area shown IMPO RTANT Please read carefully The power cord of this appliance is equipped with a three prong grounding plug that mates with a standard three prong grounding wall receptacle to minimize the possibility of electric shock The customer should have the wall receptacle and circuit checked by a qualified electrician to make sure the receptacle is properly grounded and has the correct polarity e Where a standard two prong wall receptacle is encountered it is the personal responsibility and obligation of the customer to have it replaced with a properly grounded three prong wall receptacle Do not under any circumstances cut or remove the third ground prong from the power cord DO NOT USE AN EXTENSION CORD Installation Instructions REMOVE PACKAGING AND PARTS e Lay the carton on rear face and break open the bottom flap e Set the carton upright with all four bottom flaps outward e Lift carton up and off icemaker Open Bottom Flaps e Remove all tape and packaging material from the outside and inside of the cabinet e Locate parts package with plastic plug buttons Set aside ADJUST HEIGHT OF ICE MACHINE Height
12. per air flow Before you begin 1 If a custom panel is to be installed follow the instructions shown on pages 9 and 10 Order ZIP75 black or white panel kit Order the custom panel from the cabinet manufacturer Secure the custom panel onto the ice machine Determine a method of drainage If a floor drain is to be installed the drain must be accurately located The installation of a custom door panel will affect the drain location See page 6 to determine the exact location of the floor drain front to back with or without a custom door panel A drain pump kit ZPK1 is available and will not interfere with placement of the ice machine The door swing is reversible If desired change the door swing before installation Slide the ice machine into the installation location Open and close the door to be sure there is no interference Check to be sure the ice machine can be moved back into the opening flush with adjacent cabinetry There should be no interference with the floor drain POWER SUPPLY IM PO RTANT Please read carefully FOR PERSONAL SAFETY THIS APPLIANCE MUST BE PROPERLY GROUNDED Do not use an extension cord or adapter plug with this appliance Follow National Electrical Code or prevailing local codes and ordinances This ice machine must be supplied with 115V 60Hz and connected to an individual properly grounded branch circuit and protected by a 15 or 20 amp circuit breaker
13. pper tubing that can be purchased locally Coupling Not Supplied Nut Supplied D s y sia Ferrule Not Supplied Line to l penea Icemaker GE SmartConnect Tubing e Insert the molded end of the tubing into the icemaker connection Tighten the compression nut until it is just hand tight e Tighten one additional turn with a wrench Overtightening can cause leaks e Make sure there are no sharp bends or kinks that could restrict water flow e Slide the ice machine into its permanent location e To prevent F l rattling be sure the copper tubing does not touch the side wall or other parts inside the cabinet e Open the shut off valve Check for Water Pan leaks Tighten any connections Water Valve including connections T at the valve 5 1116 if necessary REVERSE THE DOOR SWING IMPORTANT pisconnect power to the ice machine Tools Required e 1 4 and 5 16 wrench e Flat putty knife e Phillips screwdriver Parts Supplied e 4 plug buttons e 4 hinge screws on some models Fm Parts Identification For Reference Only gt Qe Hinge Pin Handle Screw Quo Om 5 16 Hex Head Endcap Screw Hinge Screw e Remove the handle screws and lift off handle On black and white models only e Remove the hinge pin from the top hinge e Lift the door off of the bottom hinge Place the hinge pin back into the top hinge Reverse the door en
14. tentially flowing onto the floor oo Drain Hose A floor drain is tly acceptable The ideal je te installation has a standpipe with a 2 to agi 1 1 2 PVC drain reducer 22 3 4 With 3 4 installed directly below Custom Panel the outlet of the drain tube 1 2 to centerline of the opening Approximately gh 3 1 2 high PEA 22 from the front BF a j or 22 3 4 when ae Locate Standpipe in exact J installing G 3 4 Center of The Cutout door panel e Drain lines must be at least 5 8 inside diameter NOTE A drain pump is necessary when a floor drain is not available Order ZPK1 Drain Pump Kit or contact your local plumber for a recommended pump available in your area TEST DRAIN HOSE ALIGNMENT Before sliding the ice machine into the cabinet opening check to be sure the bottom of the drain tube is below the rear cover To test place a pan below the drain hose Pour a gallon of water into the ice bin and check to be sure that water does not wet the rear cover Installation Instructions CONNECT WATER SUPPLY e The water line should be flushed to clear any foreign material before connecting to the icemaker e Connect the water line to the water supply tube outside of the rear access cover Water Supply Line p fo gt H o Copper Tubing e Use a standard plumbing female connector or union for 1 4 co
Download Pdf Manuals
Related Search