Yamaha RP-U100 2 Channels Receiver
Contents
1. F type connector F type adapter Mm EU 01 Connecting the AM Loop Antenna 1 Flip openthe AM and GND ANTENNA connector levers 2 Insert the AM antenna cable into the AM and GND connectors Polarity is not important 3 Close the levers to secure the cable 4 Site the AM loop antenna away from the PC and monitor 5 Rotate the antenna to find the position that offers the best reception Recommended Speaker Placement For best performance place the left and right speakers either side of your com puter monitor as shown below and posi tion them so that their fronts are flush To get the best from the sound field programs and surround effects the left and right speakers and the listener should be posi tioned so as to form a triangle with a 3 4 ratio so if for example the speakers are 60 cm 23 5 apart the listener should be 80 cm 31 5 away from each speaker Bass performance can be extended by con necting a subwoofer such as the Yamaha YST SW45 to the SUB WOOFER OUT Right speaker Left gt speaker About the Display This section explains what the various display indicators mean BA A VIRTUAL D USB PCM DD AM ST m m2. 1 Pressthe POWER switch to turn on the RP U100 The message Hello appears for a few seconds and the RP U100 returns to the state in which it was last used e g the input source that was selected when the RP U100 was turned off is selected 2 Use the input selector keys to select one of the following input sources PC AUX1 AUX2 TUNER e PC Press the PC key repeatedly to select the following PC inputs USB PC_DG and PC_AN USB select the USB port PC_DG selects the DIGITAL PC COAX IN and DIGITAL PC OPT IN and PC_AN selects the ANALOG PCIN PC PC USB 7 E PC digital VOL In PC analog Note The DIGITAL PC OPT IN has priority over the DIGITAL PC COAX IN so if you connect to both inputs the signal received at the DIGITAL PC OPT IN is used AUX1 Press the AUXI key to select the equip ment connected to the ANALOG AUX 1 IN or DIGITAL AUX 1 OPT IN connector as the input source Note The DIGITAL AUX 1 OPT IN has priority over the ANALOG AUX 1 IN so if you connect to both inputs the signal received at the DIGITAL AUX 1 OPT IN is used AUX2 Press the AUX2 key to select the equip ment connected to the ANALOG AUX 2 IN connectors as the input source e TUNER Press this key repeatedly to select the fol lowing tuner bands FM Auto Stereo FM Mono or AM VOL I 3 Start the selected input source See page 11 for more information about using the tuner 4 U
3. 0 9 Sound field program selector System Requirements Opening Page 7 680 OO Operating system Microsoft Windows 98 Engish version CPU Equivalent to Intel Pentium MMX 200 MHz or better Memory 32 MB 64 MB or more recommended Hard disk 20 MB of available space CD drive CD ROM drive or DVD ROM drive Display Video display adapter with at least 256 colors and 640x480 dots resolution Other USB port compatible wth USB standard Rev 1 0 Intel and Pentium are registered traderrarks and MMX is a trademark of Intel Corporation Windows is a registered trademark of Microsoft Corporation in the United States and or other countries Initial Steps B N Check the USB connection between the RP U100 and the PC Connect the RP U100 to the personal computer using a USB cable How to rreke the USB connection ll The RP U100 main unit can only be operated with the Application if the USB connection has been established ES Check the display settings Check that the Wndows Display Properties are set to at least 256 colors Wndows Display Properties Opening Page 8 68 0 Making the USB Connection Connection ConnectionProedue E Plug the power cable of the RP U100 into an AC outlet to set the unit to On or Standby 2 Start up the computer Connect the RP U100 and computer with the USB cable Pp Checkthecomectionn the connection 1 Open Multimedia fr
4. Turn off the RP U100 and all equip with ae other equipment for more ment to be connected before making information any connections Connecting your PC If your PC has a USB port connect it to the RP U100 s USB port using the supplied USB cable as shown below A single USB connection is all that s required to listen to audio from your PC on the RP U100 feed audio from an external source connected to the RP U100 to your PC and control the RP U100 remotely from your PC using the sup plied RP U100 Application Software Note Make sure that the USB cable is disconnected from the RP U100 before installing the RP U100 Application Software See page 16 for more information DIGITAL N um OUT al COAXIAL tos z eke F 5 gn 3 in H e 6 6 TO paz g 2 e E DIGITAL OUT OPTICAL If your PC doesn t have a USB port you can still connect it to the RP U100 using the ana log and digital inputs and outputs but cannot use the RP U100 Application Software Audio from your PC can be fed to the RP U100 using any of following connectors USB as explained above DIGITAL PC COAX IN DIGITAL PC OPT IN or ANALOG PC IN To play DVD Video discs encoded with Dolb
5. VOL Ieee a Dolby logo This indicator appears when the RP U100 is decoding a Virtual Dolby Digital or Virtual Dolby Surround audio source When the MOVIE LIVE GAME or VDD program is selected this indicator lights up regardless of the input source It does not light up when headphones are used 2 VIRTUAL This indicator appears when the RP U100 is using Virtual 3D 3 DSP This indicator appears when the DSP is processing the input signal 4 DD Dolby Digital This indicator appears when a Dolby Digital encoded digital audio signal is selected as the input source 5 MEMORY This indicator flashes when a preset sta tion is stored 6 ST STEREO This indicator appears when a stereo FM signal of sufficient strength is received 7 Message area Various messages and information appear here 8 VOL volume This indicator graphically displays the volume level setting 9 AM This indicator appears when the AM tuner is selected as the input source FM This indicator appears when the FM tuner is selected as the input source b PCM This indicator appears when a PCM digital audio signal is selected as the input source 2 USB This indicator appears when audio sig nals are sent or received via the USB port Selecting Audio Sources This section explains how to turn on the RP U100 and select input sources If any external audio equipment is con nected to the RP U100 turn it on first
6. U100 incorporates sound field programs based on such sound field data The prograrrs let you select the sound field of a famous concert hall or theater to be recreated on your personal computer equipment setup DSP sound field program icon There are icons which represent certain DSP sound field effects A sound field program can be selected by clicking the icon in the DSP sound field selector panel The icon of the currently selected sound field program is shown on the DSP button in the main panel DSP sound field program icon details Opening Page 18 680 OO DSP parameters The default parameter values of the sound field programs are usually fine for enjoying great sound but it is also possible to fine tune some of the parameters to suit individual preferences or program sources The result will be a listening experience that is truly original and thrilling Parameters are edited on the DSP Pararreter Setting Panel DSP Sound Field Program Parameter guide DSP Parameter Setting Panel details Virtual 3D Usually four to six speakers are needed to reproduce multichannel sources with Dolby Digital or Dolby Pro Logic The unique Virtual 3D technology developed by Yameha produces a convincing surround effect with just two speakers placed left and right in front of the listener The Virtual 3D setting panel also lets the user adjust 3D parameters Virtual 3D Parameter Setting Panel details Virtual Rear Speaker Position This item allows
7. When an optical connector is not being used replace its cap to prevent dust entering the connector es Connecting Speakers The following illustration shows how to connect a pair of speakers and subwoofer Con nect the left speaker to the left speaker connector on the RP U100 and the right speaker to the right speaker connector and pay careful attention to the plus and minus polarities Left speaker Right speaker SPEAKERS e i ji ala B SUB woorer CS 3E Jat MIN SPEAKER cs Subwoofer Speaker Cables Speaker Connectors Strip 10 mm of insulation off the end of Flip open the speaker connector levers each speaker cable and then twist the bare insert the bare ends of the speaker cables wires to prevent lose strands which can into the terminal holes then close the cause short circuits levers Try pulling gently on each cable to make sure that it s secure 10 1 2 Connecting an FM Antenna Connect an FM antenna tothe FM ANTENNA connector FM 75 UNBAL Sm Use the supplied indoor FM antenna only in areas with exceptionally good reception Use the supplied F type adapter to con nect an outdoor FM antenna with an F type connector
8. YAMAHA YAMAHA PERSONAL RECEIVER RP U100 Owner s Manual Thank you for purchasing the Yamaha RP U100 Personal Receiver In order to fully utilize the superior features of the Yamaha RP U100 and to enjoy years of trouble free operation please read this Owner s Manual carefully before use Contents als 1 Introduction 1 tt 2 Digital Sound Field Processing DSP 2 Controls and Functions 3 Front Patel iat sa ERR as 3 Rear Passat 4 Making Connections 5 Connecting your PC 5 Connecting Audio Equipment 6 Connecting Speakers 7 Connecting an FM Antenna 8 Connecting the AM Loop Antenna 8 Recommended Speaker Placement About the Display 9 Selecting Audio Sources 10 Using the Tuner 11 Locating Radio Stations Manually 11 Locating Radio Stations Using Auto ka ERR ERES 11 Using the Presets 12 Storing Presets Manually 12 Storing Presets Automatically 12 Selecting Presets 5 oo eese tes 13 Copying 13 Recording 14 Using Sound Field Programs 15 Using RP U100 Application SOTWANE 25 3 x 16 System Requirements 16 Installing the RP U100 Application DOING ines 16 Installing and Checking the Driver 17 Reinstalling the Driver Software 18 Using the RP U100 Application Software and Online He
9. CD player 4 eet SI o 0000 o n C fr NN MD tape recorder Personal computer Speakers Although the RP U100 can be used as part of a typical hi fi system connecting it to your PC via the USB port and running the supplied RP U100 Application Software allows you to remotely control the RP U100 from your PC and edit the sound field programs Virtual 3D Surround sound typically requires several speakers situated in front o and behind the listening position which requires a substantial amount of space that may not always be available The RP U100 uses Yamaha s unique Virtual 3D tech nology to simulate a typical surround sound system using only two speakers Virtual 3D which is used by the RP U100 s sound field programs simulates the surround effect provided by rear and center speakers creating virtual surround speakers as shown so even with only two front speakers you can still enjoy surround sound Virtual speakers Typical surround system Virtual 3D Digital Sound Field Processing DSP When you listen to a performance in a concert hall jazz club or other live music venue you not only hear the direct sound coming from the musical instruments and s
10. PC COAX IN 3 Signals received at the DIGITAL PC OPT IN or DIGITAL PC COAX IN are fed through to the DIGITAL OPT OUT 4 Has priority over the ANALOG AUX 1 IN By connecting a cassette tape recorder or MD recorder to the ANALOG AUX 2 OUT or DIGITAL OPT OUT you can record from an external audio source e g PC or CD player or the tuner When the input source is the ANALOG AUX 1 IN ANALOG AUX 2 IN or tuner the input signal can be fed to your PC via the USB connection Since sound field effects are not output by these connectors they cannot be recorded 1 Connect a tape recorder to the ANA 4 Start recording on your tape or MD LOG AUX 2 OUT or an MD recorder recorder to the DIGITAL OPT OUT as j 5 Start the input source explained on page 6 2 Turn on the recorder and the RP U100 3 Use the input selector keys to select an input source as explained on page 10 See page 11 for more information about using the tuner 14 Using Sound Field Programs The RP U100 built in DSP can simulate various acoustic environments including a concert hall and movie theater with its seven sound field programs For best results choose a program appropriate for the selected audio source 1 Press the DSP key to turn on the 2 Use the Down lt 4 or Up P key to sound field processor i VIRTUAL VOL I Active program The name of the selected sound field program appears on the display The fo
11. customers only Outdoor Antenna Grounding If an outside antenna is connected to this unit ensure the antenna system is grounded so as to provide some protection against voltage surges and built up static charges Article 810 of the National Electrical Code ANSI NFPA 70 provides information with regard to proper grounding of the mast and supporting structure grounding of the lead in wire to an antenna discharge unit size of grounding conductors location of antenna discharge unit connection to grounding electrodes and requirements for the grounding electrode EXAMPLE OF ANTENNA GROUNDING ra ANTENNA LEAD IN WIRE GROUND ANTENNA DISCHARGE UNIT NEC SECTION 810 20 ELECTRIC SERVICE EQUIPMENT GROUNDING CONDUCTORS NEC SECTION 810 21 GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM NEC ART 250 PART H NEC NATIONAL ELECTRICAL CODE Note for CATV system installers This reminder is provided to call the CATV sys tem installers attention to Article 820 40 of the NEC that provides guidelines for proper ground ing and in particular specifies that the cable ground shall be connected to the grounding sys tem of the building as close to the point of cable entry as practical We Want You Listening for a Lifetime YAMAHA and the Electronic Industries Associa tion s Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe lev
12. s supplied with this product MUST be used Follow all installation instructions Failure to follow instructions could void your FCC authorization to use this product in the USA NOTE This product has been tested and found to comply with the requirements listed in FCC Regulations Part 15 for Class B digital devices Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices This equipment generates uses radio frequencies and if not installed and used according to the instructions found in the users manual may cause interference harmful to the operation of other electronic devices Compliance with FCC regulations does not guarantee that interference will not occur in all installations If this product is found to be the source of interference which can be determined by turning the product OFF and ON please try to eliminate the problem by using one of the following measures Relocate either this product or the device that is being affected by the interference Utilize power outlets that are on different branch circuit breaker or fuse circuits or install AC line filter s In the case of radio or TV interference relocate reorient the antenna If the antenna lead in is 300 ohm ribbon lead change the lead in to coaxial type cable If these corrective measures do not produce satisfactory results
13. the unit Power Cord Protection Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience receptacles and the point where they exit from the unit 12 Cleaning The unit should be cleaned only as recommended by the manufacturer 13 When Notin Use The power cord of the unit should be unplugged from the outlet when the unit is not used for a long period of time 14 Object and Liquid Entry Care should be taken so that no objects fall into and liquids are not spilled into the unit 15 Damage Requiring Service The unit should be serviced by qualified service personnel when A The power supply cord or the plug has been damaged or B Objects have fallen or liquid has been spilled into the unit or C The unit has been exposed to rain or D The unit does not appear to operate normally or exhibits a marked change in performance or E The unit has been dropped or the enclosure damaged 16 Servicing The user should not service the unit beyond those means described in the operating instructions All other servicing should be referred to qualified service personnel 17 Overhead Power Lines An outdoor antenna should be located away from overhead power lines 18 Grounding or Polarization Precautions should be taken so that the grounding or polarization is not defeated 19 For US
14. the user to control the position of the virtual simulated rear speakers The setting is done using a graphic image on the DSP Parameter Setting Panel Virtual Rear Speaker Position details Test Tone The test tone is used to check the virtual rear speaker position Test Tone details Balance This refers to the level balance between the left and right channels The setting can be changed on the DSP Pararreter Setting Panel Balance details Personal setting Main Sub This item allows adjusting the 3D sound field effect to the conditions in a given listening room In Virtual 3D the sound field effect will vary according to environment factors such as the listening position and the shape of the room The virtual rear speaker position may therefore not exactly match the position displaved on the setting screen The Main and Sub parameters allow the listener to adjust the virtual rear speaker position to the point where the best effect is achieved Change these parameters as needed to match your personal preferences The setting can be changed on the DSP Parameter Setting Panel Personal Setting details Opening Page 19 68 1 OO Click Main Panel STANDBY mode ON mode Panel image On Panel image Off ES Main Panel Functions Standby Mode Click the Power Control button to turn on the RP Power Control U100 main unit Power control details Click the Minimize button to turn the application into an icon on t
15. ANALOG AUX 2 IN con nectors as the input source e TUNER key This key selects the AM and FM bands of the built in tuner as the input source The following bands can be selected FM Auto Stereo FM Mono or AM 2 Display The display shows various settings selected input source sound field pro gram and various other information 3 DSP key This key activates the sound field pro grams produced by the internal DSP YAMAHA CD Input selectors amp indicators These four keys explained below are used to select the input source The indicator of the selected source lights Up 4 P SET Preset key e PC key This key selects the following tuner This key selects your PC as the input modes Frequency Display mode and source The following inputs can be Preset mode selected USB port ANALOG PC IN Frequency Display mode In this DIGITAL PC COAX IN or DIGITAL PC OPT IN The DIGITAL PC OPT IN has priority over the DIGITAL PC COAX IN so if you connect to both inputs the signal received at the DIGI TAL PC OPT IN is used mode the radio frequency is displayed and you can tune the AM FM tuner either manually or automatically Preset mode In this mode you can select preset stations Al through E8 The 40 presets are arranged into five 7 Headphone jack groups from A through E with eight Stereo headphones can be connected to presets in each group this mini jack for priv
16. OM The CD ROM contains the RP U100 Application Software and online help for controlling the RP U100 from your PC e Adapter for F type antenna connector 22 Specifications Minimum RMS Output Power per Channel 30 W 30 W 20 Hz 20 kHz 6Q 0 6 THD Input Sensitivity PC IN AUXI IN AUX2 IN 150 mV 35 Analog Output Level AUX2 OUT 150 mV 3 3 kQ Subwoofer 2 0 V 1 5 kO Headphone 330 mV 47Q Tuning Range FM 87 5 107 9 MHz AM 530 1710 kHz Usable Sensitivity FM 1 5 uV AM 60 dBu or less Dimensions W x H x D 120 x 295 x 379 5 mm 4 7 x 11 6 x 15 inches Weight 5 4 kg 11 9 Ibs Specifications subject to change without notice YAMAHA ELECTRONICS CORPORATION USA 6660 ORANGETHORPE AVE BUENA PARK CALIF 90620 U S A YAMAHA CANADA MUSIC LTD 135 MILNER AVE SCARBOROUGH ONTARIO M1S 3R1 CANADA YAMAHA ELECTRONIK EUROPA G m b H SIEMENSSTR 22 34 25462 RELLINGEN BEI HAMBURG F R OF GERMANY YAMAHA ELECTRONIQUE FRANCE S A RUE AMBROISE CROIZAT BP70 CROISSY BEAUBOURG 77312 MARNE LA VALLEE CEDEX02 FRANCE YAMAHA ELECTRONICS UK LTD YAMAHA HOUSE 200 RICKMANSWORTH ROAD WATFORD HERTS WD1 7JS ENGLAND YAMAHA SCANDINAVIA A B J A WETTERGRENS GATA 1 BOX 30053 400 43 V STRA FR LUNDA SWEDEN YAMAHA MUSIC AUSTRALIA PTY LTD 17 33 MARKET ST SOUTH MELBOURNE 3205 VIC AUSTRALIA YAMAHA CORPORATION Printed in Japan V394220 1 Opening Page YAMAHA RP U100 Application Balante Mon
17. Opening Page 12 68 O L Virtual 3D Parameter Setting Panel ET TEST TOME Lets you set various Virtual 3D parameters Details Dynamic Range Setting Panel D EHHGE STD H LEVEL CUT a L LEVEL BST a Lets you control the dynamic range Details Opening Page 13 68 1 OO Quitting the Application ES How to Quit the Application Click the Close button l in the upper right corner of the main panel You can also quit the Application as follows Quitting from the system menu Ge Restore Move Size zr times s TA Breite x Close Alt FA PStart __ YAMAHA RP U100 Opening Page 14 68 Right click on the YAMAHA RP U100 icon in the task bar and select X Close from the system menu Starting the Aplication Open the Windows Start menu and select YAMAHA RP U100 The choices RP U100 and Help appear To start the RP U100 Application select RP U100 call up the help file select Help Hi Windows Update Programs Favorites 3 Documents Sh Settings A Find amp Help 3 Run Lag ij Shut Down z Accessories d Internet Explorer lA Media Pro Display Utility d Online Services d StartUp E TAMAHA RP LH OU Help E RP LITOO MS DOS Prompt J Windows Explorer If a shortcut icon has been created on the desktop start the RP U100 Application by double clicki
18. al amount of space that may not always be available The U100 features Yamaha s unique virtual 3D technology for generating virtual surround using just two speakers Even with only two front speakers this technology produces a sensation of virtual rear speakers and provides a pleasant sense of width and motion of sound behind you You can also take advantage of this RP U100 application to create virtual 3D parameters to match your personal taste USB Capture Opening Page 5 68 1 EZH USB Capture For USB capture analog signals input to the analog jacks on the RP U100 are subjected to analog digital A D conversion and then output in digital form via the USB link to a personal computer This function allows the digital data to be recorded on the corrputer using an application such as a sound recorder ES Input jacks for data capture Which input jacks are used for data capture depends on the mode selected with the input selector Input selector details Mode Input jacks used for data capture AUX1 UX1 ANALOG jack AUX2 UX2 ANALOG jack TUNER Internal tuner signal ll The USB capture function is not available in PC input mode ES Data Recording Methods 2 The RP U100 Application does not include a recording function Please use appropriate recording software installed on the computer For information on how to use the software please refer to its documentation The sound recorded with the USB
19. ate listening 8 lt gt Down Up keys with Virtual 3D effects specifically tai These keys are used to select sound field lored for headphone listening programs preset stations and tune the Power switch AM FM tuner This switch is used to turn on the RP U100 or set it to standby mode In standby mode the RP U100 can be turned on remotely from your PC using the supplied RP U100 Applica tion Software Note that the RP U100 uses a small amount of power in standby mode 6 Volume control This control adjusts the speaker and headphone volume Rear Panel C ANALOG inputs amp outputs These connectors are used to connect to the analog inputs and outputs of a PC sound card CD player or MD tape recorder The SUB WOOFER OUT can be connected to an optional subwoofer such as the Yamaha YST SW45 for enhanced bass performance 2 ANTENNA These connectors are used to connect 4 AM and FM antennas 8 SPEAKERS These connectors are used to connect a pair of speakers such as the Yamaha NS U50 4 DIGITAL inputs amp outputs These connectors are used to connect to the digital inputs and outputs of a PC sound card CD player or MD recorder If your PC has a USB port connect it to the RP U100 using the supplied USB cable for remote RP U100 control from your PC Making Connections Connection Notes Refer to the owner s manuals supplied
20. c ture audio These programs create a sound field that feels real just as if you were actually there Using RP U100 Application Software This section explains how to install the RP U100 Application Software which can be used to control the RP U100 from a PC running Windows 98 Instructions for using the RP U100 Application Software are available as online help System Requirements A computer with a 200 MHz or faster A CD ROM or DVD ROM drive Intel Pentium MMX processor or installation only equivalent A VGA monitor 640 x 480 256 color Atleast 32 MB of RAM 64 MB or more minimum recommended A USB port USB Ver 1 0 compatible A hard disk with at least 20 MB of free A 06 space Installing the RP U100 Application Software This section explains how to install the RP U100 Application Software If the Windows 98 Autorun feature is turned on the installation start up Installation Notes Make sure that the USB cable is dis connected from the RP U100 Do not connect the RP U100 to the PC s USB port until the installation is complete as the driver software will not be installed correctly and you will have to install it again as explained on page 18 Make sure that your PC meets the sys 3 screen appears automatically Continue with the installation as prompted If the Windows 98 Autorun feature is not turned on you must start the installation manually as explained below Doub
21. capture function is the original sound of the input signal The effects of the DSP sound field progranrs of the RP U100 are not recorded The data fornet supplied to the computer is 44 1 kHz 16 bit stereo Make sure that the recording software is set up properly to handle this forrrat lll While making a recording using USB capture you should close all other applications running on the computer Otherwise recording quality may be poor ES Note 2 Digital input signals cannot be captured 2 If data capture is activated while using the AUX1 DIGITAL inputs the RP U100 automatically swtches to the AUX1 ANALOG inputs After capture has ended the setting automatically returns to the AUX1 DIGITAL inputs Function List Opening Page 6 68 1 EZE The RP U100 can be operated either with the controls on the unit itself or with the Application installed on the computer ll Some functions of the RP U100 are available only fromthe Application EZET The following list shows which functions are available on the RP U100 main unit and the Application Function List O Available X Not available Function Minuit application Power standby Lo 0 1 Input mode select 1 A Customizing input selector X display Volume adjustment 0 lj 9 USB Mix Level o X 4 Mt Level balance KX Preset Store Call up Edit Preset station frequency display mt Oo 9 DP Owof
22. ect YAMAHA RP U100 in the software list YAMAHA RP U100 is highlighted 5 Click the Add Remove button and continue as prompted 19 Troubleshooting Important Information About Using the FM AM Tuner Computer equipment uses high frequency digital circuits that may cause interference on radio and television equipment located nearby If interference is a problem with the RP U100 and you cannot obtain good reception or the auto tuning functions don t work properly try the following Move the indoor FM or AM loop antenna as far away from the computer and monitor as physically possible and find the position and direction at which reception is the best FM outdoor antennas offer the best performance and should be used when the good reception is not available Be sure to use coaxial cable to connect to an outdoor antenna Use the supplied F type adapter to connect an outdoor FM antenna with an F type connector f you cannot obtain good AM reception using only the AM loop antenna connect 5 to 10 meters 16 to 32 ft of ordinary PVC coated wire to the AM connector on the RP U100 feed it through a window or other outlet and extend it horizontally Be sure to also connect the AM loop antenna Using another piece of wire connect the GND connector on the RP U100 to a good ground point such as a grounding rod Never connect the RP U100 to a metal gas or oil pipe which would cause a safety hazard or a plastic water pi
23. el One that lets the sound come through loud and clear without annoying blaring or distor tion and most importantly without affecting your sensitive hearing Since hearing damage from loud sounds is often undetectable until it is too late YAMAHA and the Electronic Industries Association s Consumer Electronics Group recommend you to avoid prolonged exposure to excessive volume levels Want You LISTENING For A Lifetime COMPLIANCE INFORMATION STATEMENT DECLARATION OF CONFORMITY PROCEDURE Responsible Party Yamaha Electronics Corp Address 6660 Orangethorpe Ave Buena Park CA90620 Telephone 714 522 9105 Type of Equipment Receiver Model Name RP U100 This device complies with Part 15 of the FCC Rules Operation is subject to the following conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation See the user manual instructions if interference to radio reception is suspected FCC INFORMATION U S A 1 IMPORTANT NOTICE DO NOT MODIFY THIS UNIT This product when installed as indicated in the instructions contained in this manual meets FCC requirements Modifications not expressly approved by Yamaha may void your authority granted by the FCC to use the product IMPORTANT When connecting this product to accessories and or another product use only high quality shielded cables Cable
24. ets You can store your favorite radio stations in the 40 presets which are organized into five groups A E with eight presets in each group Preset B3 for example is preset number 3 of group B Storing Presets Manually 1 Locate the radio station that you want to store as explained on page 11 2 Press and hold the P SET key until MEMORY flashes on the display VOL I VOL 3 While MEMORY is flashing use the P SET key to select a preset group from A through E and the Down 4 and Up P keys to select a preset number from 1 through 8 Then press and hold the P SET key until the number of the selected preset flashes The preset is stored See page 13 for information on selecting presets Storing Presets Automat ically The Auto Preset function searches for all the radio stations available in your area and stores them in presets automatically Note In steps 3 and 5 you have 10 seconds in which to make your selection If you do not press a key within that time Auto Preset will be cancelled and you ll have to start again 1 Press the TUNER key repeatedly to select one of the following tuner bands FM Auto Stereo FM Mono or AM 2 Press and hold the P SET key until AutoP appears on the display After a few seconds AI ES8 appears on the display This is the range of pre sets that will be used to store stations You can specify the first preset 1nitiall
25. ference in the operating instructions should be adhered to instructions should be followed used near water for example near a bathtub washbowl kitchen sink laundry tub in a wet basement or near a swimming pool etc by the manufacturer should be moved with care Quick stops excessive force and uneven surfaces may cause the unit and cart combination to overturn Retain Instructions The safety and operating Heed Warnings All warnings on the unit and Follow Instructions All operating and other Water and Moisture The unit should not be Carts and Stands The unit should be used only with a cart or stand that is recommended 10 11 Wall or Ceiling Mounting The unit should be mounted to a wall or ceiling only as recommended by the manufacturer Ventilation The unit should be situated so that its location or position does not interfere with its proper ventilation For example the unit should not be situated on a bed sofa rug or similar surface that may block the ventilation openings or placed in a built in installation such as a bookcase or cabinet that may impede the flow of air through the ventilation openings Heat The unit should be situated away from heat sources such as radiators stoves or other appliances that produce heat Power Sources The unit should be connected to a power supply only of the type described in the operating instructions or as marked on
26. gain using FM Mono 13 Copying Presets Once stored presets can be arranged using the Preset Copy function You may for example want to copy your favorite radio station to preset l 1 Use the P SET key to select Preset mode as shown below VOL I Preset mode 2 Use the P SET key to select the preset group and the Down lt 4 and Up gt keys to select the preset number of the preset you want to copy 3 Press and hold the P SET key until MEMORY flashes on the display 4 While MEMORY is flashing use the P SET key to select the preset group and the Down lt 4 and Up gt keys to select the preset number of the destination preset Then press and hold the P SET key until the group and number e g B3 of the preset be copied flashes on the display The preset is copied Recording The input source selected on the RP U100 is output by the ANALOG AUX 2 OUT DIG ITAL OPT OUT USB port and speakers as shown in the following table O means that a signal is output X means no signal is output Input Displa Input Connector piis Di TA Selector play p OPT OUT OUT UB jusBport XX ee ee GO p ox UC e GT NA 1 we hau DIGIALAUXTOPTIN x o X ANALOGAKIN X 9 x x ronen wer o oo X 1 9 1 Signals received at the ANALOG PC IN are fed through to the ANALOG AUX 2 OUT 2 Has priority over the DIGITAL
27. he dialog box shown on the below appears 2 EI Confirm Device Removal USB Composite Device Warning ou are about to remove this device from your system Cancel 5 Click OK to delete Confirm that USB composite device has been deleted from the list of Universal serial bus controllers Disconnect the USB cable from the PC Insert the YAMAHA RP U100 CD ROM into the CD ROM or DVD drive and reinstall the driver software Check that the driver software has been installed correctly as explained on page 17 18 Using the RP U100 Application Software and Online Help This section explains how to start the RP U100 Application Software and view the online help 1 Click the Windows 98 Start button 2 To view the online help click the and select Programs YAMAHA Windows 98 Start button and RP U100 RP U100 select Programs YAMAHA RP U100 The RP U100 Application Software Help starts The online help which explains how to use the RP U100 Application Software starts Uninstalling the RP U100 Application Software This section explains how to uninstall the RP U100 Application Software 1 Quit the RP U100 Application Soft ware and online help 2 Click the Windows 98 Start button and select Settings Control Panel The Control Panel window appears 3 Double click the Add Remove Programs icon The Add Remove Programs Properties window appears 4 Sel
28. he task bar Minimizing details Quitting the Click the Close button 3 to quit the application application Quitting details ESE Main Panel If the RP U100 main unit is on the Application will also start in the On mode The error message Cant find RP U100 appears at start up when the main unit and personal computer are not connected with a USB cable Minimizing the application
29. ined by A D conversion of analog input signals to the RP U100 USB Capture details USB MX LEVEL This function allows listening to music signals fromthe computer connected by USB even when AUX1 AUX2 or TUNER IN is selected The mx level setting determines the ratio of the USB signal to the AUX1 AUX2 or TUNER IN input signal The setting is made by dragging a slider on the Setup panel USB MIX LEVEL details SETUP DEVICE NAME This item lets you specify names that are displayed for audio devices connected to the RP U100 The setting is made by entering the names in fields on the Setup panel SETUP DEVICE NAME details MAX VOL POSITION This item sets the upper limt for the volume setting that can be made with the Application MAX VOL POSITION details Frequency display Allows you to manually tune to any frequency and to perform scan tuning Tuner Panel frequency display details Preset store Allows you to store a desired station in merrory for quick recall Preset Edit Panel details Preset recall Allows you to select any of the stored preset stations Tuner Panel Preset Recall details Opening Page 17 68 00 Preset page A page is a group of 8 preset stations displayed on a single panel This lets you organize preset stations for exarrple by music genre A short title can be specified for each page Preset page details FM AM select This refers to selecting FM Auto Stereo FM Mono or AM Use the FM AM
30. ingers but also the early reflections and natural reverberation Early reflections are the initial sound waves that bounce off the floor ceiling and walls Natural reverberation is made up of sound waves that gradually attenuate as they bounce repeatedly off multiple surfaces Early sound reflections Reverberation Early sound reflections Since the way you hear early reflections and reverberation depends on the shape and size of the building as well as the material and construction of the walls and ceiling each venue has its own unique sound called its sound field At Yamaha we have measured all the elements that make up a typical sound field direction and level of the reflections band width characteristics and delay times at famous concert halls and opera houses around the world The information gained in this process has been converted into programs that can be reproduced using Yamaha s DSP technology Using its on board DSP the RP U100 can process any audio source and recreate the atmosphere of the original venue Controls and Functions Front Panel AUX1 key This key selects the equipment con nected to the ANALOG AUX 1 IN or DIGITAL AUX 1 OPT IN connector as the input source The DIGITAL AUX 1 OPT IN has priority over the ANALOG AUX 1 IN so if you connect to both inputs the signal received at the DIGI TAL AUX 1 OPT IN is used AUX2 key This key selects the equipment con nected to the
31. le click the My Computer icon tem requirements listed previously The My Computer window opens You may be requested to insert your 5 Double click the Yamaha rp u100 Windows 98 CD ROM during the CD ROM icon installation so have it ready before The installation start up screen commencing appears 1 Turn on your PC and if it s not run 6 Continue with the installation as ning already start Windows 98 prompted 2 Insert the YAMAHA RP U100 CD ROM into the CD ROM or DVD ROM drive 16 Installing and Checking the Driver This section explains how to install the driver software and confirm that it has been installed correctly When the RP U100 is connected to the PC s USB port Windows 98 automatically detects it and installs the necessary driver software Windows 98 needs the driver software in order to communicate with the RP U100 1 Make sure that the RP U100 power cable is plugged into an AC outlet The RP U100 can be on or in standby mode when installing the driver Connect the RP U100 to a USB port on the PC using the supplied USB cable Windows 98 automatically detects the RP U100 and installs the necessary driver software You may be requested to insert your Windows 98 CD ROM Next you need to confirm that the driver software has been installed cor rectly Click the Windows 98 Start button and select Settings Control Panel The Control Panel window appears Double click the Sys
32. llowing programs are available select a sound field program Z 3 Press the DSP key to turn off the sound field processor THRU appears on the display Type Program Desoription Notes This program simulates the effect of Dolby Digital and is ideal for DVD software encoded using Dolby Digital Virtual Dolby Digital The realism provided by this program MOVIE gives the impression that you re actu ally in the scene LIVE HALL This program produces an enthusias tic atmosphere and lets you feel that you are in the midst of the action as if attending an actual jazz or rock con cert This program adds depth and sur round effects to computer games enhancing the gaming experience Sound field programs for Audio Visual This program simulates the sound field of a medium sized hall with a beautiful and rich reverberation JAZZ This program simulates the sound field of a famous New York jazz club Sound field programs for music This program simulates the sound field of a Gothic church with the unique effect of sound reverberating back and forth in a domed ceiling CHRCH 15 When headphones are con nected this program changes to a simulation program called HP3D which is specifically tai lored for headphone listening For these sound field pro grams a Yamaha DSP effect is applied to Dolby Pro Logic Dolby Digital and other sur round sounds for motion pi
33. lp 19 Uninstalling the RP U100 Application 19 Troubleshooting 20 Supplied Accessories 22 Specifications 23 Safety Instructions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL IMPORTANT Please record the serial number of this unit in the space below Model Serial No The serial number is located on the rear of the unit Retain this Owner s Manual in a safe place for future reference e Explanation of Graphical Symbols The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert you to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE 1 6A A unit and cart combination Read Instructions All the safety and operating instructions should be read before the unit is operated instructions should be retained for future re
34. ltage other than specified 7 Digital signals generated by this unit may interfere with other equipment such as tuners receivers or TVs Move this unit farther away from such equipment if interference is observed 8 Always set the volume control to minimum before starting audio playback Increase the volume gradually to an appropriate level after playback has been started Features The RP U100 Personal Receiver brings Yamahas Near Field Cinema DSP high quality audio to your PC Digital Sound Field Processing tech nology and Virtual Dolby Digital pro The USB interface allows remote DO vide live music performance and RP U100 control from your PC using the supplied RP U100 Application Soft movie theater surround sound ware plus various audio I O options deal for use with computer games The built in AM FM stereo tuner offers Internet music CD ROM DVD mul 40 programmable presets timedia software and more Introduction Using Yamaha s unique DSP technology the RP U100 can bring excitement and realism to any audio source by simulating the acoustic environments of concert halls movie the aters and so on with only two speakers With its stylish vertical design the RP U100 allows you to use various audio sources including your PC CD player MD or tape recorder and the built in AM FM tuner as shown below FM antenna AM antenna HP U100 SE SE 0 ET L T
35. nd right in front of the listener ES Compatible with a Wide Variety of Formats The RP U100 provides USB digital and analog input output connectors for hookup of a computer and almost any type of audio equipment EZSU SB Capture The RP U100 also features a USB capture function for recording An analog input signal supplied to the RP U100 is converted to digital form and sent to the PC via the USB link These data can then be recorded using dedicated recording software Opening Page 4680 DOLBY DIGITAL 1 This is a theater acoustics format developed by Dolby Labs USA for home use Dolby Digital is a method to reproduce completely independent audio utilizing digital compression technology on 5 1 channels consisting of 3 front channels and 2 rear channels for a total of 5 channels plus a low frequency effect channel The conventional Dolby Pro Logic format 3 front channels and 1 rear channel mixed into 2 stereo channels by a matrix circuit Dolby Digital creates a 3 dimensional surround effect of superior quality CI Manufactured under license from Dolby Laboratories Dolby Pro Logic and the double D symbol are traderrarks of Dolby Laboratories Confidential Unpublished Works 1992 1997 Dolby Laboratories All rights reserved Virtual 3D Technology Reproducing a Dolby Digital or Dolby Pro Logic source requires the use of a total of 4 6 speakers placed before and behind the listener using a substanti
36. ng the shortcut icon IE Shortcut icon Opening Page 15 68 1 0 0 Open the folder where the RP U100 Application is installed and double click the RP U100 icon ai RP U100 application icon Glossary Main panel This is the main panel of the Application It lets you switch the power on and off perform basic functions and call up other panels Main Panel details Main Panel details Setup Dialog Lets you make various parameter settings Setup Dialog details Tuner Panel frequency display Lets you manually select a station on the tuner Tuner Panel frequency display details Tuner Panel preset display This panel is for selecting a preset station on the tuner Tuner Panel preset display details Preset Edit Panel This panel serves for storing preset stations Preset Edit panel details DSP Sound Field Selector Panel Lets you select a DSP sound field program and perform related functions DSP Sound Field Selector Panel details DSP Parameter Setting Panel Lets you edit various DSP parameters DSP Parameter Setting Panel details Opening Page 16 68 110 Virtual 3D Parameter Setting Panel Lets you edit various Virtual 3D parameters Virtual 3D Parameter Setting Panel details Dynamic Range Setting Panel Lets you change the dynamic range settings Dynamic Range Setting Panel details USB Capture This function uses the USB link to send digital data to the corrputer for recording The data are obta
37. o TEST Opening Page 1 68000 How to Use Help Company names and product names mentioned in the help are tradenarks or registered trademarks of their respective owners Changes may be made in the help contents without prior notice ESHI Contents Index and Search FUNTON Display the index by selecting the Contents tab on the move pane The help contents are arranged Contents hierarchicallv Opening Page amp Search amp Index amp contents ett ntr oduct ion MN RP UTOD Application MER Support Information 2 68 OL Related items are arranged in sequence fromthe top on down so vou can visually select the page you need Keywords important terms used in the help file are listed here Keywords listed here can be directly selected or can be searched by entering that keyword This function lets you search for any word or phrase contained in the help file Enter the word you want to find and a list of pages containing that word will be displayed Select the related page you need fromthe page list to view its contents ES The pointer changes to a hand when placed on an item that can be clicked i Hand Symbol Clicking on the item indicated by the hand brings up a related page or irege Basic knowledge of Windows 98 Internet Explorer or similar software is needed to use the RP U100 Application Help See Windows Help fo
38. omthe Windows Control Panel and select the Audio tag Click here to open the Audio tag on the control panel 2 Select YAMAHA RP U100 USB Audio as the Preferred Device for playback and M Start up Tm application and check that the RP U100 is controlled by the application Play some audio on the computer CD MIDI WAVE etc and confirm that the RP U100 reproduces the sound RP U100 Application Panels This is as the main panel of the Application Allows you to switch the RP U100 on and off control basic functions and access various other panels Details Opening Page 9 68 1 Setup Dialog SETUP DIALOG Ea SETUP DENICE HAME awa AUX 2 MAME USB LEVEL Mix OFF MIN HAYK x CANCEL Lets you set various system parameters Details Tuner Panel Frequency Display Tuner Mono Lets you perform manual and scan tuning Details Opening Page 10 680 00 Tuner Panel Preset Display Tuner Mono Lets you select preset stations Details Preset Edit Panel coy dA PRESET ELIT Tuner a uo SEARCH START CLEAR WONO PAGE TITLE EDIT Lets you store stations in memory Details Opening Page 11 68 DSP Sound Field Selector Panel Lets you set various DSP parameters Details DSP Parameter Setting Panel EffectLewel Room Size SeatPosition ik 2k dk Bk Hz Ld LOAD TEE Lets you set various DSP parameters Details
39. pe Outdoor AM antenna AM loop antenna included Outdoor FM antenna Antenna adapter FM 750 UNBAL SPEAKERS AN 75 ohm coaxial cable Ground 20 If your RP U100 does not operate as expected check the items below Possible Cause d power pug piHggeo Insert the power plug correctly into the wall outlet correctly Pressing the POWER switch does not turn on the RP U100 Switch off the power correct A speaker cable is shorted the speaker connections then switch on the power again Select the source that you want to listen to No input source is selected When using the PC input There is no sound source be sure to select the correct input USB digital or analog A connection is incorrect Check the connections TS SOUNGE pm ei oi Switch on the DSP no effect There is a humming noise An analog connection is incor Insert the analog plugs cor rect rectly Using the RP U100 affects TV reception or the performance of other equipment These equipment may be situ Move these equipment away ated too close to the RP U100 from the RP U100 The preset settings are lost if The Presets do not work the RP U100 is unplugged for Reprogram the presets more than two weeks Troubleshooting the FM Tuner Possible Cause Adjust the angle and location of the FM antenna to minimize the Interference from the ignition noise If tha
40. please contact the local retailer authorized to distribute this type of product If you can not locate the appropriate retailer please contact Yamaha Electronics Corp 6660 Orangethorpe Ave Buena Park CA90620 The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries DIGITAL Manufactured under license from Dolby Laboratories Dolby Pro Logic and the double D symbol are trademarks of Dolby Laboratories Intel and Pentium are registered trademarks and MMX is a trademark of Intel Corporation Windows is a registered trademark of Microsoft Corporation in the United States and or other countries IV Read the Following Before Operating the Unit 1 To ensure the finest performance please 9 Do not attempt to clean the unit with chemical read this manual carefully Keep it in a safe solvents this might damage the finish Use a place for future reference clean dry cloth 2 Install this unit in a cool dry clean place 10 Be sure to read the Troubleshooting section away from windows heat sources sources of regarding common operating errors before excessive vibration dust moisture and cold concluding that the unit is faulty Avoid sources of hum transformers motors 11 When not planning to use this unit for long To prevent fire or electrical shock do not periods of time i e vacation etc expose the unit to rain or water di
41. r more information on using Wndows 98 Wndows is a registered trademark of Microsoft Corporation in the United States and or other countries Opening Page 3 68 OO Introducing the RP U100 ET Personal Receiver RP U100 The Personal Receiver RP U100 is a USB compatible multimedia amplifier with built in tuner While it can of course be used as a conventional receiver connecting the RP 0100 to a personal computer opens up a host of exciting possibilities for audio fun and entertainment ES Total Computer Control All RP U100 functions can be operated from a PC running the dedicated RP U100 Application A convenient USB link is used between the RP U100 main unit and the computer ES Yamaha Digital Sound Field Processing The RP U100 incorporates various DSP sound field programs specially adapted for audio and multimedia applications Using a wealth of stored data the amp can faithfully reproduce the acoustic properties of world famous concert halls and live venues Exciting theater type sound compatible wth DVD movie formats such as Dolby Digital is also available EXSU virtual 3D Gives the Feeling of Being There Sophisticated Yamaha technology transports you right to where the action is Usually several front and rear speakers are needed to reproduce multichannel sources such as Dolby Digital The unique Virtual 3D technology developed by Yamaha produces a realistic surround effect with just two speakers placed left a
42. sconnect the AC power plug from the wall 3 Never open the cabinet If something drops outlet into the unit contact your dealer 12 To prevent lightning damage disconnect the 4 Do not use force with switches controls or AC power plug and disconnect the antenna connection wires When moving the unit first cable when there is an electrical storm disconnect the power plug and the wires connected to other equipment Never pull the This unit is not fully disconnected from the AC eS power source as long as it is connected to the 5 Do not touch the top cover since it may wall outlet even if this unit itself is turned off become hot after extended high power This state is called standby mode operation This cover has openings for proper In this mode the unit consumes a small amount ventilation of the unit Do not place any of electricity objects on these openings If the openings are obstructed the temperature inside the unit will rise rapidly Also be sure to install the unit vertically not horizontally in a well ventilated area and allow enough clearance from the surrounding objects Otherwise the receiver may be damaged or a fire may be caused 6 The voltage used must be the same as that specified on this unit Using this unit with a higher voltage than specified is dangerous and may result in fire or other accidents YAMAHA will not be held responsible for any damage resulting from use of this unit with a vo
43. se the volume control to adjust the volume level 10 Using the Tuner Locating Radio Stations Manually 1 11 Use the P SET key to select Frequency Display mode VOL I In Frequency Display mode the radio frequency is displayed as shown here Press the TUNER key repeatedly to select one of the following tuner bands FM Auto Stereo FM Mono or AM FM Auto Stereo FM Mono VOL 1 Use the Down lt 4 and Up 5 keys to locate radio stations Use the Down lt 4 key to lower the fre quency the Up gt key to increase it Note If there is noise in an FM Stereo broadcast try switching to FM Mono Locating Radio Stations Using Auto Search 1 Press the TUNER key repeatedly to select one of the following tuner bands FM Auto Stereo FM Mono or AM FM Auto Stereo FM Mono VOL Iu 2 Use the P SET key to select the Frequency Display mode VOL I Frequency Display mode In Frequency Display mode the radio frequency is displayed as shown here 3 Press and hold the Down lt 4 or Up gt key to start Auto Search Auto Search starts from the current radio frequency Use the Down lt d key to search down the Up P key to search up The RP U100 stops search ing when it locates a station To search for another station repeat step 3 Note If Auto Search cannot locate a station due to its weak signal try locating the station manually Using the Pres
44. selector button and the FM mode selector button FM AM selector details FM mode selector details Manual tuning Refers to receiving broadcast stations by setting the frequency manually Use the manual tuning up down buttons Manual tuning details Auto tuning auto scan This function automatically scans the current frequency band and stops when a station is found Use the auto scan up down buttons Auto tuning auto scan details RP U100 DSP SOUND FIELD TERMS Sound field The unique acoustic characteristics of a given space In locations such as a concert hall we of course hear the direct sound coming for example from an instrument But our ears also pick up the so called early reflections which is the sound being reflected from boundaries such as walls floors and the ceiling Finally we hear reverberation namely the sound being repeatedly bounced back and forth and gradually decaying The early reflections and reverberation characteristics depend on factors such as the size and shape of the interior space and the type of furnishing The resulting acoustics are unique to a particular hall or room This is what is called a sound field DSP sound field program Yamaha has collected a vast amount of sound field data at famous concert halls opera houses and other venues around the world These data express the direction of reflections their intensity frequency characteristics delay time and many other factors The RP
45. t does not eliminate A popping noise can be heard system of a motorcycle or auto the noise install an outdoor FM mobile is being picked up antenna Use a coaxial cable for the antenna connection Stereo broadcasts are accom The antenna signal is too weak panied by an unpleasant back or the signal of the station you Install an outdoor FM antenna ground noise are receiving is weak Auto tuning cannot locate a sta a multi element antenna The station is too weak tion Use manual tuning 21 Troubleshooting the AM Tuner Possible Cause Adjust the direction of the AM loop antenna If that does not improve the sound adjust the angle and location of the antenna to find the optimum position Try reconnecting the AM loop Auto tuning cannot locate a sta antenna The station is too weak tion Use manual tuning Use an outdoor AM antenna Use an outdoor AM antenna Interference noise is being Make sure that all electrical A continuous popping noise caused by lightning a fluores equipment is grounded cor can be heard cent light a motor or electrical rectly In some situations it may equipment with a thermostat be difficult to completely elimi nate this problem The signal is weak or the antenna connection is incom plete The station can hardly be heard or the sound quality is poor Supplied Accessories e AM loop antenna USB cable e CD R
46. tem icon The System Properties window appears as shown Click the Device Manager tab The Device Manager window appears Click the View devices by type option button Click the symbol next to Human Interface Devices and make sure that YAMAHA RP U100 HID Audio Controls appears in the list as shown Click the symbol next to Sound video and game controllers and make sure that YAMAHA RP U100 USB Audio appears in the list as shown 17 9 Click the symbol next to Universal serial bus controller and make sure that YAMAHA RP U100 Composite USB Device appears in the list as shown System Properties 31 General Device Manager Hardware Profiles Performance View devices by type C View devices by connection 4g Human Interface Devices 48 HID compliant consumer control device 44 YAMAHA RP LI100 HID Audio Controls H E Keyboard E Monitors Mouse Network adapters Ports COM LPT Sound video and game controllers YAMAHA RP U100 USB Audio FA System devices Universal serial bus controller YAMAHA RP U100 Composite USB Device ae Properties Refresh Remove Print Close ance Note The device list on your PC may differ to that shown here Reinstalling the Driver Software If you connect the RP U100 to the PC s USB port before installing the supplied appli cation soft
47. ware the RP U100 driver software will not be installed correctly and the System Properties window will display the following items 3 USB Audio Device in the Sound video and game controllers list USB Human Interface Device in the Human Interfaces list USB Composite Device in the Uni versal serial bus controllers list Although you will be able to control the application software and listen to music you must reinstall the RP U100 device driver if you want the PC to rec ognize the RP U100 correctly as explained below Make sure that the RP U100 is con nectedto the PC s USB port On the System Properties window click the symbol next to Universal serial bus controller Select USB Composite Device System Properties HEI General Device Manager Hardware Profiles Performance View devices by type View devices by connection H E Disk drives 1 mj Display adapters gt Floppy disk controllers z Hard disk controllers 33 Human Interface Devices Keyboard 1 m Monitors Mouse Network adapters Ports COM LPT amp Sound video and game controllers 1 System devices Universal serial bus controller s Intel 823715B EB PCI to USB Universal Host Controller USB Composite Device USB Root Hub Properties Refresh Remove Print Select USB Composite Device 4 Click Delete T
48. y A1 as follows The last preset E8 can not be changed 3 While A1 ES is displayed use the P SET key to select a preset group from A through E and the Down 4 and Up gt keys to select a preset number from 1 through 8 4 Press and hold the P SET key until START appears on the display 5 While START is displayed press the Down lt a or Up P key to start the Auto Preset function Auto Preset starts from the current radio frequency Use the Down lt 4 key to search down and the Up gt key to search up When a radio station is located the RP U100 stores it to the next available preset Auto Preset stops when the entire band has been searched Note When a preset is stored by the Auto Preset function the previously stored radio station is overwritten To protect radio stations stored for example in presets A1 through A4 specify A5 as the first preset as explained previously 12 Selecting Presets 1 Use the P SET key to select Preset mode as shown below FM VOL I Preset mode Use the P SET key to select a preset group from A through E Use the Down lt 4 and Up 5 keys to select a preset number from 1 through 8 The radio station stored in the preset is selected Press the TUNER key to check the frequency of the radio station The frequency is displayed for a few seconds Note If there is noise in an FM Stereo broadcast store the preset a
49. y Digital your computer must have a DVD ROM drive and DVD Video decoder board which should be connected to the RP U100 via the DIGITAL PC COAX IN or DIGITAL PC OPT IN Note The DIGITAL PC OPT IN has priority over the DIGITAL PC COAX IN so if you connect to both inputs the signal received at the DIGITAL PC OPT IN is used 5 Connecting Audio Equipment The following illustration shows how to connect a CD player and MD or tape recorder The CD player is shown connected to the RP U 100 using both analog and digital connec tions However it s not necessary to make both connections Since digital offers higher quality use the digital connection if your CD player had a digital output The MD tape recorder is shown connected to the RP U100 using analog and digital connections If your MD player has a digital input connect it as shown Be careful not to mix up the left and right connections DIGITAL OUT OPTICAL LINE OUT a Dum CD player 0000 z DIGITAL E IN OPTICAL as LINE OUT 4 A A IN PLAY REC Note The DIGITAL AUX 1 OPT IN has priority over the ANALOG AUX 1 IN so if you connect to both inputs the signal received at the DIGITAL AUX 1 OPT IN is used Protective Caps When connecting to an optical connector remove its protective cap first
Download Pdf Manuals
Related Search