Home

SuperMicro 5011h Motherboard

1. External High Density SCSI Connector 5011H only Chapter 7 AMIBIOS Chapter 7 BIOS 7 1 Introduction This chapter describes the AMIBIOS for the 5011H 5011E The AMI ROM BIOS is stored in a Flash EEPROM and can be easily upgraded using a floppy disk based program Note Due to periodic changes to BIOS some settings may have been added or deleted and might not yet be recorded in this manual Refer to the Manual Download area of our web site for any changes to BIOS that are not reflected in this manual System BIOS The BIOS is the Basic Input Output System used in all IBM PC XT AT and PS 2 compatible computers The BIOS ROM stores the system param eters such as amount of memory type of disk drives and video displays etc BIOS ROM requires very little power When the computer is turned off a back up battery provides power to the BIOS ROM enabling it to retain the system parameters Each time the computer is powered on the computer is then configured with the values stored in the BIOS ROM by the system BIOS which gains control when the computer is powered on How To Change the Configuration Data The configuration data that determines the system parameters may be changed by entering the BIOS Setup utility This Setup utility can be ac cessed by
2. Load Failsafe Defaults Highlighting this setting and then pressing lt Enter gt provides the safest set of parameters for the system Use them if the system is behaving errati cally Discard Changes Highlighting this setting and then pressing lt Enter gt will ignore any changes you made in the BIOS Setup program but will not exit the BIOS Setup pro gram 7 38 Appendix A BIOS Error Beep Codes Appendix A BIOS Error Beep Codes amp Messages During the POST Power On Self Test routines which are performed each time the system is powered on errors may occur Non fatal errors are those which in most cases allow the system to continue the boot up process The error messages normally appear on the screen Fatal errors are those which will not allow the system to continue the boot up procedure If a fatal error occurs you should consult with your system manufacturer for possible repairs These fatal errors are usually communicated through a series of audible beeps The numbers on the fatal error list on the following page correspond to the number of beeps for the corresponding error All errors listed with the exception of Beep Code 8 are fatal errors A 1 SUPERSERVER 5011H 5011E Manual AMIBIOS Error Beep Codes read write error Beep Error Message Description Code 1 beep Refresh The memory refresh circuitry on the motherboard is faulty 2 beeps BIOS ROM file The
3. UO Controller Hub ICH2 The ICH2 I O Controller Hub subsystem on the P3TSSR P3TSSE integrates many of the Input Output functions of the 815E chipset including UDMA 100 Bus Master IDE controllers It also provides the interface to the PCI Bus and communicates with the MCH over a dedicated hub interface In addition to the UDMA 100 Bus Master IDE controllers this powerful ICH2 also in cludes two USB controllers that offer 24 Mbps of bandwidth across three ports ICH2 also features an enhanced AC 97 interface that supports full surround sound for the Dolby Digital Audio used on DVDs Firmware Hub FWH The FWH is a component that brings added security and manageability to the PC platform infrastructure This device includes an integrated Random 1 4 Chapter 1 Introduction Number Generator RNG for stronger encryption digital signing and secu rity protocols The FWH stores the system BIOS and video BIOS to eliminate a redundant nonvolatile memory component Processors The P3TSSR P3TSSE supports single 370 pin Pentium III FCPGA 600 MHz 1 26 GHz and Celeron FCPGA PPGA 300 700 MHz processors with Front Side Bus Speeds of 133 100 66 MHz Please refer to the support section of our web site for a complete listing of supported processors http www supermicro com TechSupport htm Memory The P3TSSR P3TSSE has three 3 168 pin DIMM sockets that can support up to 512 MB of unbuffered PC133 and PC100 SDRAM Module sizes of
4. 3 PO 4 Ground 4 Ground 5 Key 5 Ground Chapter 5 Advanced Motherboard Setup Fan Headers Fan Header Pin Definitions There are several fan headers on CPU CHASSIS and OH FANs H Pin the P3TSSR P3TSSE that provide Number Datinition cooling for various components 1 Ground black i 2 12V red In addition to one fan header for 3 Tachometer the processor located near the Caution These fan headers are DC power ATX Power Supply there are one overheat and two chassis fan headers located next to the DIMM modules When installed in the C810 1U rackmount chassis only the main blower fan is used The blower fan should be connected to the chassis fan2 blow fan header See the motherboard lay out for locations Refer to the table on the right for pin defini tions Note The maximum current limitation is 0 6 amps for each onboard fan not to exceed 1 25 amps for any two fans for example both CPU fans both chassis fans or both overheat fans Serial Ports P Serial Port Pin Definitions Serial connector COM1 is located COM1 COM2 beside the VGA port see Figure Pin Number Definition Pin Number Definition 5 8 COM2 is a header located 1 pen 6 DSH 2 Serial In 7 RTS behind the mouse keyboard ports 3 Serial Out 8 CTS See the motherboard layout for Se Ne locations See the table on the right for pin definitions 5 17 SUPER
5. Accessing the inside of the 5011H 5011E see Figure 2 5a 2 5b First release the retention screws that secure the unit to the rack Grasp the two handles on either side and pull the unit straight out until it locks you will hear a click Next depress the two buttons on the top of the chassis to release the top cover There is a large rectangular recess in the middle front of the top cover to help you push the cover away from you until it stops You can then lift the top cover from the chassis to gain full access to the inside of the server 2 Check the CPU processor You should have one processor already installed into the system board Each processor should have its own heatsink attached See Section 5 5 for instructions on processor installation 3 Verify the proper CPU core bus ratio setting The CPU FSB speed is set with jumpers JP11 and JP12 see Section 5 9 for details The CPU speed can also be changed by software control in BIOS see CPU Speed Setting The CPU Speed Setting will show you the actual CPU speed for each FSB speed option selected 4 Check the system memory Your 5011H 5011E server system may have come with system memory already installed Make sure all DIMMs are fully seated in their slots For details on adding system memory refer to Section 5 5 5 Installing add on cards If desired you can install an add on card to the system See Section 5 7 for details on installing a PCI add on card 6 Check all cab
6. The precharge time is the number of cycles it takes for the RAS to accumulate a charge before a DRAM refresh Insufficient recharge time may cause the DRAM to lose data The settings are Fast and Slow which is more stable 7 18 Chapter 7 AMIBIOS System Memory Frequency This option allows the system memory frequency to be adjusted The set tings are 100 MHz for PC100 memory 133 MHz for PC133 memory and Auto which allows the system memory frequency to auto select itself SDRAM Refresh This option sets the refresh rate for the system memory Settings include Auto 15 6 mS 7 8 mS and 128 CLKS DRAM Cycle Time SCLKS This option allows you set the DRAM cycle time to 5 7 6 8 or Auto CAS Latency SCLKS This option allows you to set the CAS latency time to 3 2 or Auto RAS to CAS Delay SCLKS The settings for this option are 3 2 or Auto RAS Precharge SCLKS This option sets the RAS precharge time The settings are 3 2 or Auto DRAM Page Closing Policy The settings for this option are Close and Open Memory Hole Some ISA cards may require specific areas of memory to function This can be done by choosing the 15 MB 16 MB option to reserve the area The settings for this option are Disabled and 15 MB 16 MB 7 19 SUPERSERVER 5011H 5011E User s Manual ICH2 Configuration You can use this screen to select options for the ICH2 Configuration Use the up and down arrow keys to select an item and the p
7. click into place to be correctly and fully installed in their bays e The floppy disk drive cable has seven twisted wires e A red mark on a wire typically designates the location of pin 1 e A single floppy disk drive ribbon cable has 34 wires and two connectors to provide for two floppy disk drives The connector with twisted wires always connects to drive A and the connector that does not have twisted wires always connects to drive B 6 8 Chapter 6 Advanced Chassis Setup 6 5 Power Supply The SuperServer 5011H 5011E has a single 200 watt power supply This power supply has an auto switching capability which enables it to auto matically sense and operate anywhere between 110v and 220v A power on off switch is located at the back of the power supply Turning this power switch to the off position will remove both main and standby power from the system Power Supply Failure If the power supply unit fails the system will shut down and you will need to replace the power supply unit Replacement units can be ordered di rectly from Supermicro see contact infomation in Chapter 1 Replacing the Power Supply 1 Accessing the inside of the SuperServer 5011H 5011E To replace a power supply you must first remove the top chassis cover To do so first release the retention screws that secure the unit to the rack Grasp the two handles on either side and pull the unit straight out until it locks you will hear a click
8. disabling cache memory Uncompressing the POST code next Next initializing the CPU and the CPU data area The CMOS checksum calculation is done next The CMOS checksum calculation is done Initializing the CMOS status register for date and time next The CMOS status register is initialized Next performing any required initialization before the keyboard BAT command is issued The keyboard controller input buffer is free Next issuing the BAT command to the keyboard controller The keyboard controller BAT command result has been verified Next performing any necessary initialization after the keyboard controller BAT command test The initialization after the keyboard controller BAT command test is done The keyboard command byte is written next The keyboard controller command byte is written Next issuing the Pin 23 and 24 blocking and unblocking command Next checking if lt End or lt Ins gt keys were pressed during power on Initializing CMOS RAM if the Initialize CMOS RAM in every boot AMIBIOS POST option was set in AMIBCP or the lt End gt key was pressed Next disabling DMA controllers 1 and 2 and interrupt controllers 1 and 2 The video display has been disabled Port B has been initialized Next initializing the chipset The 8254 timer test will begin next The 8254 timer test is over Starting the memory refresh test next The memory refresh line is toggling Checking the 15 second on off time next Passing cont
9. 5011H 5011E Manual Connecting the Control Panel JF1 contains header pins for various front control panel connectors See Figure 5 1 for the pin locations of the various front control panel buttons and LED indicators Please note that even and odd numbered pins are on opposite sides All JF1 wires have been bundled into a single ribbon cable to simplify this connection Make sure the red wire plugs into pin 1 as marked on the board The other end connects to JP4 of the Control Panel PCB board located just behind the system status LEDs on the chassis The control signals are all on the even numbered pins See pages 5 12 to 5 14 for details and pin descriptions In addition to the 2 pin Power LED header on JF1 there is a 3 pin header for the same function at J50 on the motherboard which is located near JET Figure 5 1 Control Panel Header Pins Control Power LED pins 15 16 Control HDD LED pins 13 14 Control NIC1 LED pins 11 12 Control NIC2 LED pins 9 10 Control Overheat LED pins 7 8 X Key Reset Button pins 3 4 Power Button pins 1 2 Power LED ol Control x e WS J50 5 4 Chapter 5 Advanced Motherboard Setup 5 4 I O Ports The I O ports are color coded in conformance with the PC 99 specification See Figure 5 2 below for the colors and locations of the various I O ports Figure 5 2 Mouse Green A cose Keyboard USB COM1 Port Purple Ports Turquoise Black Note T
10. Auto setting auto detects USB keyboards or mice and if found allows them to be utilized during boot and while using DOS PCI Slot1 IRQ Preferrence PCI Slot2 IRQ Preferrence PCI Slot3 IRQ Preferrence PCI Slot4 IRQ Preferrence The settings for the above options are Auto 3 4 5 7 9 10 11 12 14 15 IRQ3 IRQ 4 IRQ5 IRQ 7 IRQ 9 IRQ 10 IRQ 11 IRQ 14 IRQ 15 The settings for the above options are Available and Reserved Available allows the specified IRQ to be available for use by PCI PnP devices Re served means the specified IRQ is reserved for use by Legacy ISA de vices 7 25 SUPERSERVER 5011H 5011E User s Manual DMA Channel 0 DMA Channel 1 DMA Channel 3 DMA Channel 5 DMA Channel 6 DMA Channel 7 Each of the above list of DMA channel setting options can be set to Avail able and Reserved Available means the specified DMA channel is avail able for use by PCI PnP devices Reserved means the specified DMA chan nel is reserved for use by Legacy ISA devices Reserved Memory Size This option specifies the size of a memory area to be reserved for Legacy ISA adapter cards The settings are Disabled 16k 32k and 64k 7 26 Chapter 7 AMIBIOS 7 7 Power Setup Choose Power Setup from the AMIBIOS Setup main menu All Power Setup options are described in this section The Power Setup screen is shown below BIOS SETUP UTILITY Main Advanced Chipset PCIPnP Power Boot Security Exit A
11. BIOS was unable to find absent the specific file name required to flash the BIOS 3 beeps Base 64KB Memory failure occurred in the memory failure first 64KB of Memory 4 beeps Flash program The flash was properly successful programmed with the BIOS ROM file 5 beeps Media read error The floppy or ATAPI media is not presented or cannot be read 6 beeps Keyboard The keyboard controller may controller Gate be bad The BIOS cannot A20 failure switch to protected mode 7 beeps Processor The CPU generated an exception exception interrupt interrupt error 8 beeps Display memory The system video adapter is either missing or its memory is faulty This is not a fatal error 10 beeps Flash erase error The flash device was unable to be properly programmed 11 beeps Flash program The flash device was unable to error be properly programmed 12 beeps BIOS ROM file The BIOS ROM file found does incorrect size not match the size of the flash device 13 beeps BIOS ROM image The BIOS ROM file layout mismatch configuration does not match image present in the flash device 5 short _1 Memory Error No memory detected in the long beeps system 6 short 1 Memory Error EDO memory detected in long beeps system 7 short 1 SMBUS Error SMBUS error long beeps A 2 Appendix B AMIBIOS POST Checkpoint Codes Appendix B AMIBIOS POST Checkpoint Codes When AMIBIOS performs the Power On Self Test it writes diagn
12. Controller This option allows the user to enable or disable the integrated IDE Control ler The settings include Disabled Primary Secondary and Both Select Disabled to disable the Integrated IDE Controller Select Primary to en able the Primary IDE ontroller only Select Secondary to enable the Sec ondary IDE Controller only Select Both to enable both Primary and Sec ondary IDE Controllers Primary IDE Master When entering Setup BIOS automatically detects the presence of IDE devices This displays the auto detection status of the IDE de vices You can also manually configure the IDE drives by providing the following information 7 8 Chapter 7 AMIBIOS Type This option sets the type of device that the AMIBIOS attempts to boot from after AMIBIOS POST is completed The settings include Not installed Auto CDROM and ARMD The Auto setting allows BIOS to automatically detect the presence of the IDE controller LBA Large Mode LBA Logical Block Addressing is a method of addressing data on a disk drive In LBA mode the maximum drive capac ity is 137 GB The settings are Disabled and Auto Select Disabled to disable LBA mode Select Auto to enable LBA mode if your device supports it and is not already formatted with the LBA mode Block Multi Sector Transfer Mode This option sets the block mode multi sector transfers option The settings include Disabled and Auto Disabled This op tion prevents
13. Inc Use the Up Down arrow keys to select the Health Monitor Features line When the Health Monitor Features line is highlighted hit ENTER to display its items Health Monitor Features The BIOS continuously monitors the health of your system by measuring certain voltage levels and temperatures 7 4 Chapter 7 AMIBIOS CPU Overheat Warning This option allows you to Enable or Disable a system overheat warning signal used to notify you in the event of a dangerous rise in heat levels CPU Overheat Warning This option allows you to specify the temperature threshold that when exceeded will trigger the overheat warning alarm The rest of the Health Monitor menu lists various voltages and temperatures as they are currently being measured These include CPU current tempera ture CPU voltage the RPMs of the CPU H W MonitorINO CPU1 H W MonitorIN2 3 3V H W MonitorIN3 5V H W MonitorIN4 12v H W MonitorIN5 12V CPU Fan Chassis Fan 1 Chassis Fan 2 and thermal control fans The settings are Enabled or Disabled 7 5 SUPERSERVER 5011H 5011E User s Manual Super I O Configuration After selecting the settings for Health Monitor Features use the Up Down arrow keys to select the SuperlO Configuration line When the SuperlO Configuration line is highlighted hit ENTER to display the submenu BIOS SETUP UTILITY Configure Winbond627t Port s and Parallel P Serial Portl Address 3F8
14. The power button on the front of the chassis is usually the soft off meaning that there is still power being supplied to the motherboard even though the system looks completely off Hard off means that there is not power being supplied to the system at all The only power is coming from the backup battery on the motherboard 7 29 SUPERSERVER 5011H 5011E User s Manual Green PC Monitor Power State This option specifies the power state that a green PC compliant monitor enters when BIOS places it in a power saving state after the specified period of display inactivity has expired The settings include Standby Sus pend and Off Video Power Down Mode This option specifies the power state that the VGA video subsystem enters after the specified period of display inactivity has expired The settings include Disabled Standby and Suspend Hard Disk Power Down Mode This option specifies the power conserving state that the hard disk drive s enters after the specified period of inactivity has expired The settings include Disabled Standby and Suspend Hard Disk Time Out Minutes This option specifies the length of hard disk inactivity time that should expire before entering the power conserving state specified in the previous set ting The settings include Disabled and increments of 1 15 minutes Display Activity This option specifies if BIOS is to monitor for display activity when in a power saving state The Ignore setting
15. These are word checkpoints The low byte of checkpoint is the system BIOS checkpoint where control is passed to the different bus routines The high byte of checkpoint indicates that the routine is being executed in Different buses High Byte The high byte of these checkpoints includes the following information Bits 7 4 0000 Function 0 0001 Function 1 0010 Function 2 0011 Function 3 0100 Function 4 0101 Function 5 0110 Function 6 0111 Function 7 Description Disable all devices on the bus Initialize static devices on the bus Initialize output devices on the bus Initialize input devices on the bus Initialize IPL devices on the bus Initiate general devices on the bus Initialize error reporting on the bus Initialize add on ROMs for all buses Bits 3 0 Specify the bus OS GO MA O Generic DIM Device Initialization Manager Onboard System devices ISA devices EISA devices ISA PnP devices PCI devices B 8 Appendix C List of Figures Appendix C List of Figures Description Page Rear I O Panel 1 3 Identifying the Sections of the Rack Rails 2 3 Installing Chassis Rails 2 4 Installing the Server into a Rack 2 5 Installing the Server into a Telco Rack 2 6 Accessing the Inside of the 5011H 5011E 2 8 2 9 Control Panel Header Pins 5 4 UO Ports 5 5 FCPGA Socket Empty and with Processor Installed 5 6 Heatsink Installation Procedure 5 6 Side View of DIMM Installation into Slot 5 7 32 b
16. Two 2 SCA SCSI drive carriers 5011H only SCSI Accessories 5011H only One 1 internal 68 pin Ultra160 SCSI cable for SCA SCSI backplane One 1 set of SCSI driver diskettes One 1 SCSI manual 1 1 SUPERSERVER 501 1H 5011E Manual e One 1 5V 32 bit 33 MHz PCI slot riser card D Rackmount hardware with screws Two 2 rack rail assemblies Six 6 brackets for mounting the rack rails in a rack telco rack J One 1 CD ROM containing drivers and utilities Intel s LANDesk Client Manager LAN driver SCSI driver 5011H only SuperServer 5011H 5011E User s Manual Type and number depends upon the configuration ordered 1 2 Server Chassis Features The SuperServer 5011H 5011E is a high end scaleable 1U rackmount server platform designed with today s most state of the art features The following is a general outline of the main features of the SC810 chassis System Power When configured as a SuperSever 5011H 5011E the SC810 chassis in cludes a 200W power supply SCSI Subsystem 5011H only The SCSI subsystem on the 5011H supports two 80 pin SCA Ultra160 SCSI hard drives Standard 1 drives are supported SCA Single Connection Attachment The SCSI drives are connected to an SCA backplane that provides power bus termination and configuration settings The SCSI drives are also hot swap units Control Panel The SC810 s control panel provides important system monitoring and control information
17. blower fan plugs into a chassis fan header on the motherboard and operates at full rpm continu ously If it breaks down the ambient air temperature inside the chassis will rise and activate an overheat LED 1 3 SUPERSERVER 501 1H 5011E Manual 1 3 Mainboard Features At the heart of the SuperServer 5010H 5010E lies the P3TSSR P3TSSE a single processor motherboard designed to provide maximum performance Below are the main features of the P3TSSR P3TSSE Chipset Overview Intel s 815E chipset is made up of three main components the Graphics and Memory Controller Hub GMCH the I O Controller Hub ICH and the Firm ware Hub FWH The GMCH integrates a 133 100 66 MHz system bus controller a 2D 3D graphics accelerator AGP2x 4x discrete graphics card a 133 100 MHz SDRAM controller and a high speed hub architecture inter face that communicates with the ICH The ICH integrates a UDMA 100 con troller USB controllers and other I O functions see below The FWH stores both system and video BIOS and includes a Random Number Genera tor RNG Graphics and Memory Controller Hub GMCH The GMCH includes the host CPU interface DRAM interface ICH2 inter face and 4xAGP interface for the 815E chipset It contains advanced power management logic and supports dual channels for DRAM The AGP 2 0 interface supports 4x data transfers and operates at a peak bandwidth of 1066 MB sec The MCH host interface bus runs at 133 100 66 MHz
18. events as read The settings are OK and Cancel 7 15 SUPERSERVER 5011H 5011E User s Manual 7 5 Chipset Setup Choose Chipset Setup from the AMIBIOS Setup Utility main menu The screen is shown below All Chipset Setup options are described following the screen You can use this screen to select options for the GHCH Configuration BIOS SETUP UTILITY Main Advanced Chipset PCIPnP Power Boot Security Exit gt GMCH Configuration Options for MCH gt ICH gConfiguration Processor Serial Number Disabled CPU Latency Timer Disabled c000 16k Shadow Cached WP c400 16k Shadow Cached WP C800 16k Shadow Disabl Cc00 16k Shadow Disabl DO00 16k Shadow Disabl D400 16k Shadow Disabl Select Screen D800 16k Shadow Disabl TL Select Item DCO0 16k Shadow Disabl Change Option F1 General Help F10 Save and Exit ESC Exit V02 03 C Copyright 1985 2000 American Megatrends Inc GMCH Configuration You can use this screen to select options for the GMCH Configuration Use the up and down arrow keys to select an item and the plus and minus keys to change the option setting The settings are described on the following pages Primary Video Device This option specifies the primary display device on your system Settings include Internal External PCI External AGP and Auto Auto This setting allows the BIOS to select the primary video device at bootup Internal This setting allows the onboard video display a
19. from JF1 on the motherboard to JP4 on the Control Panel PCB printed circuit board Make sure the red wire plugs into pin 1 on both JF1 and JP4 Pull all excess cabling out of the airflow path The LEDs inform you of system status See Chapter 3 for details on the LEDs and the control panel buttons Details on JF1 can be found in Chapter 5 Chapter 6 Advanced Chassis Setup 6 3 System Fans One 10 cm blower fan provides all the cooling needed for the SuperServer 5011H 5011E The chassis includes air seals under the blower fan and at the chassis cross section which separates the drive bay area from the motherboard area of the chassis to promote better airflow It is highly important that the air seal is properly installed and making a good seal in order for the cooling air to circulate properly through the chassis See Figure 6 3 for locations System Fan Failure The blower fan runs at a full 100 rpm If the fan fails the ambient air temperature in the chassis will rise and activate the overheat LED on the control panel You will need to power down the system to replace this fan Replacing System Cooling Fans 1 Removing the blower fan After turning off the power to the system first remove the chassis cover and unplug the fan cable from the motherboard Lift the blower fan from the mounting posts and pull it completely out from the motherboard See Figure 6 3 2 Installing a new blower fan Replace the failed fan
20. intrusion header auto switching voltage regulators chassis and CPU overheat sensors virus protection and BIOS rescue 1 6 Chapter 1 Introduction 1 4 Contacting Supermicro Headquarters Address Tel Fax E mail Web site Super Micro Computer Inc 980 Rock Ave San Jose CA 95131 U S A 1 408 503 8000 1 408 503 8008 marketing supermicro com General Information support supermicro com Technical Support www supermicro com European Office Address Super Micro Computer B V Het Sterrenbeeld 28 5215 ML s Hertogenbosch The Netherlands Tel 31 0 73 6400390 Fax 31 0 73 6416525 E mail sales supermicro nl General Information support supermicro nl Technical Support rma supermicro nl Customer Support Asia Pacific Address 3F 753 Chung Cheng Road Chung Ho City Taipei Hsien Taiwan R O C Tel 886 2 8228 1366 Fax 886 2 8221 2790 Web Site www supermicro com tw Email support supermicro com tw Technical Support Tel 886 2 8228 1366 ext 132 1 7 SUPERSERVER 5011H 5011E Manual NOTES 1 8 Chapter 2 Server Installation Chapter 2 Server Installation 2 1 Overview This chapter provides a quick setup checklist to get your SuperServer 5011H 5011E up and running Following these steps in the order given should enable you to have the system operational within a minimum amount of time This quick setup assumes that your SuperServer 5
21. means any display activity will not wake the system up from a power management state The Monitor setting allows display activity to wake up the system from a power management state Manual Throttle Ratio When in a power management state throttling can be used to lower power consumption and reduce heat This option allows the CPU to operate at a reduced average power which includes a sacrifice in performance The settings include 87 5 75 0 62 5 50 37 5 25 and 12 5 A setting of 75 0 means the BIOS will throttle back the CPU clock to operate 75 of the time 7 30 Chapter 7 AMIBIOS THRM Throttle Ratio THRM throttling is used to lower power consumption and reduce heat The settings include 87 5 75 0 62 5 50 37 5 25 and 12 5 Intruder Sel This option allows you to set the Intruder SEL setting to SCI or SMI SCI stands for System Control Interrupt This is considered to be ACPI Ad vanced Configuration and Power Interface mode The operating system uses the SCI interrupt to process ACPI Advanced Configuration and Power Interface events signaled by GPEs general Purpose Event whether the system is asleep or awake when the event occurs In other words the wake event has the side effect of causing the system to wake up if it is asleep but its primary purpose is to generate an SCI that notifies the oper ating system that the event has occurred SMI stands for System Manage ment Interrupt This is
22. more base memory Onboard LAN1 Option ROM Use this option to either Enable or Disable the use of ROM for LAN1 If you disable onboard LAN1 with JP35 on the motherboard you should also dis able this BIOS setting to free up more base memory Onboard LAN2 Option ROM Use this option to either Enable or Disable the use of ROM for LAN2 If you disable onboard LAN1 with JP31 on the motherboard you should also dis able this BIOS setting to free up more base memory 7 14 Chapter 7 AMIBIOS Event Log Configuration Event Logging This option Enables or Disables the logging of events You can use this screen to select options for the Event Log Configuration Settings You can access sub screens to view the event log and mark all events as read Use the up and down arrow keys to select an item and the plus and minus keys to change the option setting The settings are described on the following pages The screen is shown below ECC Event Logging This option Enables or Disables the logging of ECC events The events logged by AMIBIOS are post errors such as a bad BIOS floppy errors or hard drive errors Clear All Event Logs This option can be used to tell the system to clear the event log on the next boot up The settings are No and Yes View Event Log This option allows the user view the events of the system The settings are No and Yes Mark all Events as Read This option allows the user to use the screen to mark all
23. pressing lt Del gt at the appropriate time during system boot Starting the Setup Utility Normally the only visible POST Power On Self Test routine is the memory test As the memory is being tested press the lt Delete gt key to enter the main menu of the BIOS Setup utility From the main menu you can access the other setup screens such as the Chipset and Power menus Section 7 3 gives detailed descriptions of each parameter setting in the Setup utility An AMIBIOS identification string is displayed at the left bottom corner of the screen below the copyright message 7 1 SUPERSERVER 5011H 5011E User s Manual 7 2 BIOS Features e Supports Plug and Play V1 0A and DMI 2 3 Supports Intel PCI Peripheral Component Interconnect PME local bus specification e Supports Advanced Power Management APM specification v 1 1 e Supports ACPI e Supports Flash ROM AMIBIOS supports the LS120 drive made by Matsushita Kotobuki Electronics Industries Ltd The LS120 e Can be used as a boot device KR Is accessible as the next available floppy drive AMIBIOS supports PC Health Monitoring chips When a failure occurs in a monitored activity AMIBIOS can sound an alarm and display a message The PC Health Monitoring chips monitor e CPU temperature Additional temperature sensors Chassis intrusion detector Five positive voltage inputs Two negative voltage inputs e Three fan speed monitor inputs 7 3 Running Setu
24. should 7 13 SUPERSERVER 5011H 5011E User s Manual be used to slow the computer system down or to troubleshoot error mes sages Write Thru This option allows the computer system to use the internal CPU L1 cache as Write Through cache Write Through cache is slower than Write Back cache It performs write operations to the internal L1 CPU cache and system memory simultaneously Write Back This option allows the computer system to use the internal CPU L1 cache as Write Back cache Write Back cache is faster than Write Through cache Write Back cache is a caching method in which modifications to data in the cache aren t copied to the cache source until absolutely necessary Write back caching is available on all CPUs supported by this BIOS With these CPUs write operations stored in the L1 cache aren t copied to main memory until absolutely necessary This is the default setting External Cache This option is for enabling or disabling the internal CPU L2 cache Settings include Disabled Write Thru and Write Back See description above Peripheral Device Configurations This option allows the user to set the configurations for the devices listed below The options for these devices are Disabled and Enabled Onboard SCSI Option ROM 5011H only Use this option to either Enable or Disable the use of ROM for the onboard SCSI If you disable onboard SCSI with JP34 on the P3TSSR you should also disable this BIOS setting to free up
25. well as the activity and health of specific components There are also two buttons on the chassis control panel and an on off switch on the power supply This chapter explains the meanings of all LED indicators and the appropriate response you may need to take 3 2 Control Panel Buttons There are two push button buttons located on the front of the chassis These are in order from left to right a reset button and a power on off button RESET e RESET The reset switch reboots the system D POWER This is the main power switch which is used to apply or turn off the main system power Turning off system power with this button removes the main power but keeps standby power supplied to the system See also the power supply on off switch in Section 3 5 SUPERSERVER 5011H 5011E Manual 3 3 Control Panel LEDs The control panel located on the front of the SC810 chassis has five LEDs These LEDs provide you with critical information related to different parts of the system This section explains what each LED indicates when illumi nated and any corrective action you may need to take J OVERHEAT Indicates an overheat condition in the chassis This may be caused by cables obstructing the airflow in the system or the ambient room temperature being too warm You should also check to make sure that the chassis cover is installed and that all fans are present and operat ing normally Finally check the air seals for damage The air
26. with an identical 10 cm 12 volt fan available from Supermicro Position the new fan in its proper place in the chassis by fitting the fan onto the fan mounting posts in the chassis After the new fan has been installed plug the fan cable back into the same chassis fan header on the motherboard you removed it from Make sure the air seal under the fan is properly installed and creating a good seal Power up the system and check that the fan is working properly and that the LED on the control panel has turned off Finish by replacing the top panel of the chassis SUPERSERVER 5011H 5011E Manual Fan Mounting Posts Blower Fan Figure 6 3 System Cooling Fans 6 4 Drive Bay Installation Removal Accessing the Drive Bays SCSI Drives You do not need to access the inside of the chassis to replace or swap SCSI drives Proceed to the next step for instructions Note You must use standard 1 high 80 pin SCA SCSI drives in the SuperServer 5011H CD ROM Floppy Disk Drive For installing removing the CD ROM or floppy disk drive you will need to gain access to the inside of the 5011H 5011E by removing the top cover of the chassis Proceed to the CD ROM and Floppy Drive Installation section later in this chapter for instructions Note Only a slim CD ROM drive will fit in the 5011H 5011E Chapter 6 Advanced Chassis Setup SCSI Drive Installation 5011H only 1 Mounting a SCSI drive in a drive carrier The SCSI driv
27. 0 x 25 Color 80 x 25 and monochrome Parity Check Use this option to either Enable or Disable the use of memory parity check ing Boot to OS 2 This option can be used to boot the system to an OS 2 operating system The settings are No and Yes Wait for F1 if Error This settings for this option are Enabled and Disabled Disabled This prevents the AMIBIOS to wait on an error for user intervention This setting should be used if there is a known reason for a BIOS error to appear An example would be a system administrator must remote boot the system The computer system does not have a keyboard currently attached If this setting is set the system will continue to bootup in to the operating system HEI is enabled the system will wait until the BIOS setup is entered Enabled This option allows the system BIOS to wait for any error If an error is detected pressing lt F1 gt will enter Setup and the BIOS setting can be adjusted to fix the problem This normally happens when upgrading the hardware and not setting the BIOS to recognize it Hit Delete Message Displayed This option tells the system to display or not display the Hit Delete to Enter Setup message The settings are Enabled and Disabled Internal Cache This option is for enabling or disabling the internal CPU L1 cache Settings include Disabled Write Thru and Write Back Disabled This option pre vents the system from using the internal CPU L1 cache This setting
28. 011H 5011E system has come to you with the processor and memory preinstalled If your system is not already fully integrated with a motherboard processor system memory etc please turn to the chapter or section noted in each step for details on installing specific components 2 2 Unpacking the SuperServer 5011H 5011E You should inspect the box the SuperServer 5011H 5011E was shipped in and note if it was damaged in any way If the server itself shows damage you should file a damage claim with the carrier who delivered it Decide on a suitable location for the rack unit that will hold the SuperServer 5011H 5011E It should be situated in a clean dust free area that is well ventilated Avoid areas where heat electrical noise and electromagnetic fields are generated You will also need it placed near a grounded power outlet Read the Rack and Server Precautions in the next section 2 3 Preparing for Setup The box the SuperServer 5011H 5011E was shipped in should include two sets of rail assemblies two rail mounting brackets and the mounting screws you will need to install the system into the rack Follow the steps in the order given to complete the installation process in a minimum amount of time Please read this section in its entirety before you begin the installation procedure outlined in the sections that follow 2 1 SUPERSERVER 5011H 5011E Manual Choosing a Setup Location Leave enough clearance in front of the
29. 03 C Copyright 1985 2000 American Megatrends Inc Supervisor Password User Password AMIBIOS provides both Supervisor and User password functions If you use both passwords the Supervisor password must be set first The sys tem can be configured so that all users must enter a password every time the system boots or when AMIBIOS Setup is executed using either or both the Supervisor password or User password The Supervisor and User passwords activate two different levels of password security If you select password support you are prompted for a 1 6 character password Type the password on the keyboard The password does not appear on the screen when typed Make sure you write it down If you forget it you must clear CMOS and reconfigure Remember your Password Keep a record of the new password when the password is changed If you forget the password you must erase the system configuration information in CMOS 7 35 SUPERSERVER 5011H 5011E User s Manual Change Supervisor Password This option allows you to change a supervisor password that was entered previously Change User Password This option allows you to change a user password that was entered previ ously Clear User Password Use this option to clear the user password so that it is not required to be entered when the system boots up Boot Sector Virus Protection This option allows you to enable or disable a virus detection program to protect the boot
30. 128MB 256MB and 512MB may be used to populate the DIMM slots The DIMM slots are situated at a 25 degree angle to create a low profile and to promote efficient airflow through the chassis Onboard SCSI 5011H only Onboard SCSI is provided with an Adaptec AIC 7899 SCSI controller chip which supports dual channel Ultra160 SCSI at a burst throughput rate of 160 MB sec for each channel The P3TSSR provides two SCSI ports one internal 68 pin LVD Ultra160 connector on Channel A and one external internal shared 68 pin Ultra160 SCSI connector channel B PCI Expansion Slots The P3TSSR P3TSSE has four 32 bit 33 MHz PCI slots available One riser card is included with the system for use with 32 bit PCI cards Network Interface Controllers NIC The P38TSSR P3TSSE supports two Network Interface controllers NIC based on Intel s 82559 and 82562 chips For the 5011H server which is based on the P3TSSR mainboard two 82559 Ethernet chips are included in the system SUPERSERVER 501 1H 5011E Manual Onboard Controllers Ports An onboard IDE controller supports one floppy drive and up to four UDMA 100 hard drives or ATAPI devices Onboard I O ports include one COM port two USB ports PS 2 mouse and keyboard ports a video Graphics port and two LAN NIC ports which back each other up in case one port loses connection Other Features Other onboard features that promote system health include eight voltage monitors a chassis
31. 9 RST 26 MSG 60 MSG 27 SEL 61 SEL 28 C0 D 62 C D 29 REQ 63 REQ 30 Del 64 1 0 31 DB 8 65 DB 8 32 DB 9 66 DB 9 33 DB 10 67 DB 10 34 DB 11 68 DB 11 5 24 Chapter 6 Advanced Chassis Setup Chapter 6 Advanced Chassis Setup This chapter covers the steps required to install components and perform maintenance on the SC810 chassis For component installation follow the steps in the order given to eliminate the most common problems encountered If some steps are unnecessary skip ahead to the step that follows Tools Required The only tool you will need to install components and perform maintainance is a Philips screwdriver 6 1 Static Sensitive Devices Electric Static Discharge ESD can damage electronic components To prevent damage to any printed circuit boards PCBs it is important to handle them very carefully The following measures are generally suffi cient to protect your equipment from ESD discharge Precautions Use a grounded wrist strap designed to prevent static discharge Touch a grounded metal object before removing any board from its anti static bag Handle a board by its edges only do not touch its components periph eral chips memory modules or gold contacts When handling chips or modules avoid touching their pins Put the motherboard add on cards and peripherals back into their anti static bags when not in use For grounding purposes mak
32. CI Slot3 IRQ Preference Available Exit PCI Slot4 IRQ Preference Available V02 03 C Copyright 1985 2000 American Megatrends Inc Plug amp Play OS Choose the No setting for computers that do not meet the Plug and Play specifications which will allow the BIOS to configure all the devices in the system Choosing the Yes setting lets the operating system configure PnP devices that are not required for boot up if the system has a PnP operating system The operating system would have the ability to change interrupt I O and DMA settings Normally this option is set to Disabled Reset Configuration Data Choosing the Yes setting will cause the PnP configuration data in the BIOS to be cleared on the next boot up Choosing the No setting does not force PnP data to be cleared on the next boot 7 23 SUPERSERVER 5011H 5011E User s Manual PCI Latency Timer This option specifies the latency timing of the PCI clocks for all PCI devices Settings include 32 64 96 128 160 192 224 and 248 PCI clocks Allocate IRQ to PCI VGA This option lets you allocate an interrupt request IRQ to the PCI VGA adapter card if used The settings are Yes and No Palette Snooping When enabled this option informs PCI devices that an ISA graphics device is installed The settings are Disabled and Enabled This does not neces sarily indicate a physical ISA adapter card The graphics chipset can be mounted on a PCI card Always ch
33. CPI Aware 0 S No Suspend to RAM Support Disabled Repost Video on S3 Resume Yes Power Management APM Enabled Standby Time Out Disabled Suspend Power Saving S1 Suspend Time Out Disabled Power Button Mode On Off AfterG3 Enable Disabled Green PC Monitor Power State Suspend amp Select Screen Video Power Down Mode Suspend N Hard Disk Power Down Mode Suspend Hard Disk Time Out Minute Disabled Display Activity Ignore Manual Throttle Ratio 50 THRM throttle Ratio 50 Intruder Sel SMI Select Item Change Option F1 General Help F10 Save and Exit ESC Exit V02 03 C Copyright 1985 2000 American Megatrends Inc 7 27 SUPERSERVER 5011H 5011E User s Manual ACPI Aware O S This option allows the system to utilize Intel s ACPI Advanced Configuration and Power Interface specification Settings are No and Yes DOS Windows 3 x Windows 95 and Windows NT are examples of non ACPI aware operating systems Windows 98 Windows ME and Windows 2000 are examples of ACPI aware operating systems Suspend to RAM Support This allows you to enable or disable the Suspend to RAM feature Settings are Disabled and Enabled The Disabled setting prevents the system from saving information to main memory when in a low power state Enabled causes the system to enter a low power state instead of being completely shut off This allows the computer system to bootup in a few seconds Suspend to RAM STR is a t
34. D WITH THE PRODUCT INCLUDING THE COSTS OF REPAIRING REPLACING INTEGRATING INSTALLING OR RECOVERING SUCH HARDWARE SOFTWARE OR DATA Any disputes arising between manufacturer and customer shall be governed by the laws of Santa Clara County in the State of California USA The State of California County of Santa Clara shall be the exclusive venue for the resolution of any such disputes Supermicro s total liability for all claims will not exceed the price paid for the hardware product Unless you request and receive written permission from SUPER MICRO COMPUTER you may not copy any part of this document Information in this document is subject to change without notice Other products and companies referred to herein are trademarks or registered trademarks of their respective companies or mark holders Copyright 2001 by SUPER MICRO COMPUTER INC All rights reserved Printed in the United States of America Preface Preface About This Manual This manual is written for professional system integrators and PC techni cians It provides information for the installation and use of the Super Server 5011H 5011E Installation and maintainance should be performed by experienced technicians only The SuperServer 5011H 5011E is a high end single processor 1U rackmount server based on the SC810 1U rackmount server chassis and either the Super P3TSSR for the 5011H or the P3TSSE for the 5011E mainboard The P3TSSR P3TSSE mainboard
35. E Connectors Pin Number Function Pin Number Function 1 Reset IDE 2 GND 3 Host Data 7 4 Host Data 8 There are no jumpers to config 5 Host Data 6 6 Host Data 9 7 Host Data 5 8 Host Data 10 ure the onboard IDE connectors e Geet ag AE J18 and J19 Refer to the table 13 Host Data2 14 Host Data 13 on the left for pin definitions 15 Host Data 1 16 Host Data 14 17 Host Data 0 18 Host Data 15 19 GND 20 Key 2 DRQ3 22 GND 23 1 0 Write 24 GND 25 UO Read 26 GND 27 IOCHRDY 28 BALE 29 DACK3 30 GND 3 IRQ14 32 10CS16 33 Addr 34 GND 35 Addr 0 36 Addr 2 37 Chip Select 0 38 Chip Select 1 39 Activity 40 GND 5 23 SUPERSERVER 5011H 5011E Manual Ulira160 SCSI Connectors 5011H only Refer to the table below for pin the definitions of the Ultra160 SCSI connectors located at JA1 JA2 and JA3 68 pin Ultra160 SCSI Connectors JA1 JA2 JA3 Connector Connector Contact Contact Number Signal Names Number Signal Names 1 DB 12 35 DB 12 2 DB 13 36 DB 13 3 DB 14 37 DB 14 4 DB 15 38 DB 15 5 DB P1 39 DB P1 6 DB 0 40 DB 0 7 DB 1 41 DB 1 8 DB 2 42 DB 2 9 DB 3 43 DB 3 10 DB 4 44 DB 4 11 DB 5 45 DB 5 12 DB 6 46 DB 6 13 DB 7 47 DB 7 14 DB P 48 DB P 15 GROUND 49 GROUND 16 DIFFSENS 50 GROUND 17 TERMPWR 51 TERMPWR 18 TERMPWR ER TERMPWR 19 RESERVED 53 RESERVED 20 GROUND 54 GROUND 21 ATN 55 ATN 22 GROUND 56 GROUND 23 BSY 57 BSY 24 ACK 58 ACK 25 RST 5
36. LEDs indicate power on network activity hard disk drive ac tivity and system overheat conditions The control panel also includes a main power button and a system reset button Chapter 1 Introduction Rear I O Panel The SC810 is a 1U rackmount chassis Its I O panel provides one mother board expansion slot one COM port another is internal two USB ports 5011H only PS 2 mouse and keyboard ports a graphics port and two Ethernet ports See Figure 1 1 Figure 1 1 Rear I O Panel GE ou T IU EC 2 I 550 O External SCSI 5011H only Vay Saar Ge EE J d O Coc DG gt l etetsts soot Cre LE e JOR ele Port NI keyboard USB COM1 VGA Graphics Ethernet Port Port Port Port Ports Cooling System The SC810 chassis has an innovative cooling design that includes a 10 cm blower system cooling intake fan and one optional 4 cm fan that can be installed in the midsection of the chassis The
37. Next depress the two buttons on the top of the chassis to release the top cover and push it away from you You can then lift the top cover from the chassis to gain full access to the inside of the server 2 Removing the power supply See Figure 6 7 First unplug the power cord from the system To remove the failed power unit remove the two screws on the back of the power supply which secure it to the chassis You can then lift the unit straight out of the chassis The power cord should have already been removed 3 Installing a new power supply Replace the failed unit with another unit of the same wattage It is highly recommended to replace it with the exact same power supply Carefully insert the new unit into position in the chassis and secure it with the two screws at the rear of the unit Before reconnecting the power cord make sure the power switch on the power supply is in the off position Then reconnect the power cord replace the chassis top cover and push the unit back into the rack Finish by turning the power switch on the power supply on and then depress the power button on the front of the system SUPERSERVER 5011H 5011E Manual Figure 6 7 Chassis Rear View 5011E ES D Power Supply UO Ports see Figure 1 1 5011H PCI Slot
38. Ory iiinraroani aehinaii asridan aeaaaee aia aaas 5 7 5 7 Adding PONGardS E 5 8 P3TSSR Layout and Quick Reference sssssssieseesinrrerrererere 5 10 11 P3TSSE Layout and Quick Reference sssssssssieseerinrrnrrerrnrrerrn 5 12 13 5 8 Connector Definitions Power Supply Connector ccecsecesceseeceseeeeeseeneeeeeeeeeeseaeseeaeeneeereeees Infrared Connector Ge sec echt enger te cadet 2 Ee Power LED Universal Serial BUS USB Fan Headers ovine isinven Rite AE SERA Eeer ge ah Serial POrts ioo cesta Sova dee edd ASA ATX PS 2 Keyboard and Mouse Ports LANA EAN2 POMS Aaen hd ee deed eege eege geed Wake OneRing hav aide ed Aoi aia ee etd Wake On LAN euro Nee EENEG SUPERSERVER 5011H 5011E Manual Chassis Intrusion e eat EHS Wu TT EE Explanation of JUMPESS cceccesssccsscesesesscesscesesesseesscesonssceeseceseeteenteoes Front Side Bus Speed ai CMOS Cleariiiavecunthaainki eege Speaker Enable Disable cccecceceeceeseeseeeeeeeeeeeeeeeeeeeeeaeeaeeeeeeeneeeeeeaees LAN1 LAN2 Enable Disable eceeeceeeseeeeeseeeeeeeeeeeeeeeaeeeeeeeeeeeeeaeeas 5 21 Keyboard vWake Hlt e dregrerseeek gie gege E 5 21 LVD Channel A SCSI Termination Enable Disable 5011H 5 22 LVD Channel B SCSI Termination Enable Disable 501 1H 5 22 SCSI Enable Disable 5011H oo ee eeeeceeseeseeneeeeeeeeeeeeeeeeetaeeaeeaeeneeeees Watchdog Rest EE 5 10 Floppy Hard Disk and SCSI Connection
39. P 4x si us ws OH FAN D JP35 wn Ea H E PO EI ao gt a ICH2 SS Io e So ia lla e dE Ww a PCI2 JP36 ih a UI a JP31 C B J26 BIOS PCI 3 FWH J18 PCI 4 w A J19 JL1 JBT1 WOL JP32 KEE JWOR 5 12 Chapter 5 Advanced Motherboard Setup P3TSSE Quick Reference for 5011E Jumpers Description Default Setting JBT1 CMOS Clear Pins 1 2 Normal JP11 12 Front Side Bus Speed Both Pins 1 2 Auto JP31 LAN2 Enable Disable Closed Enabled JP35 LAN1 Enable Disable Closed Enabled JP36 Speaker Watchdog Enable Closed Speaker JPWAKE Keyboard Wake Up Pins 1 2 Disabled Connectors Description CH FAN 1 Chassis Fan Header COM1 COM2 COM1 COM2 Serial Port Connector CPU FAN CPU Fan Header IR Infrared Device Header J1 J2 J3 Memory DIMM Slots J18 J19 IDE Hard Disk Drive Connectors J29 ATX Power Connector J30 PS 2 Keyboard Mouse Ports JF 1 Front Control Panel Header JL1 Chassis Intrusion Header JP26 Floppy Disk Drive Connector JP32 Speaker Header JWOR Wake On Ring Header LAN1 LAN2 Ethernet Ports OH FAN Overheat Fan Header PW LED Power LED Header USBO 1 Universal Serial Bus Ports USB2 3 Universal Serial Bus Headers VGA VGA Monitor Port WOL Wake on LAN Header SUPERSERVER 5011H 5011E Manual 5 8 Connector Definitions Power Supply Connector ATX Power Supply 20 pin Connector Pin Definitions J29 The primary pow
40. PA2 SCSI Channel B Termination JP11 12 Front Side Bus Speed JP31 LAN2 Enable Disable JP34 SCSI Enable Disable JP35 LAN1 Enable Disable JP36 Speaker Watchdog Enable JPWAKE Keyboard Wake Up Connectors Description CH FAN 1 Chassis Fan Header COM1 COM2 CPU FAN CPU Fan Header IR Infrared Device Header J1 J2 J3 Memory DIMM Slots J18 J19 IDE Hard Disk Drive Connectors J29 ATX Power Connector J30 PS 2 Keyboard Mouse Ports JF1 Front Control Panel Header JL1 Chassis Intrusion Header JP26 Floppy Disk Drive Connector JP32 Speaker Header JWOR Wake On Ring Header LAN1 LAN2 Ethernet Ports OH FAN Overheat Fan Header PW LED Power LED Header USBO 1 Universal Serial Bus Ports USB2 3 Universal Serial Bus Headers VGA VGA Monitor Port WOL Wake on LAN Header Jumpers not indicated are for test purposes only SUPERSERVER 5011H 5011E Manual Figure 5 9 Super P3TSSE Layout not drawn to scale 8 7 Iess J30 J29 KB Mouse JPWAKE CPU FAN ATX POWER ill D z JF1 lt KK 8 USBO 1 COM Pill FCPGA or a Celeron Processor So N VGA GMCH a E a LAN CH FAN LANZ z lt ind BATTERY E w_ z o 3 D AG
41. PERSERVER 5011H 5011E Manual Installing the Chassis Rails Position the fixed chassis rail sections you just removed along the side of the 5011H 5011E chassis making sure the five screw holes line up Note that these two rails are left right specific Screw the rail securely to the side of the chassis see Figure 2 2 Repeat this procedure for the other rail on the other side of the chassis You will also need to attach the rail brackets when installing into a telco rack Locking Tabs As you have seen both chassis rails have a locking tab which serves two functions The first is to lock the server into place when installed and pushed fully into the rack which is its normal position Secondly these tabs also lock the server in place when fully extended from the rack This prevents the server from coming completely out of the rack when you pull it out for servicing Figure 2 2 Installing Chassis Rails Installing the Rack Rails Determine where you want to place the SuperServer 5011H 5011E in the rack see Rack and Server Precautions in Section 2 3 Position the fixed rack rail sliding rail guide assemblies at the desired location in the rack keeping the sliding rail guide facing the inside of the rack Screw the 2 4 Chapter 2 Server Installation assembly securely to the rack using the brackets provided Attach the other assembly to the other side of the rack making sure that both are at the exact same height a
42. Refer to this chapter when adding or removing processors or main memory and when reconfiguring the motherboard Chapter 6 Advanced Chassis Setup Refer to Chapter 6 for detailed information on the SC810 1U rackmount server chassis You should follow the procedures given in this chapter when installing removing or reconfiguring SCSI or peripheral drives and when replacing system power supply units and cooling fans Chapter 7 BIOS The BIOS chapter includes an introduction to BIOS and provides detailed information on running the CMOS Setup Utility Appendix A BIOS Error Beep Codes and Messages Appendix B Post Diagnostic Error Messages Appendix C List of Figures Appendix D System Specifications Preface SOUI UUOD Gau siodune S8YOUMS did 10 D9UU0D inoke7 gw sq Sp129 19d pseoqiayjoW Ko ue YoUMS Aiddnsg 19MOdq UOoUEUEISUu oI21u11gdng soeds wajshs Addne 19M0q Ndo sqa1isos Buljoejuog dnjas sainbi4 jo S17 suj Aeg ang Ssl0d O I Ajajes asa SO soinjea4 dmes SOW QU 01 U09 uoljeye s ul pieoquiey sobessoy 10113 Buluuny sue4 wa shs sajqeg Ayayes yoey Belg 1s0q B19UayH suong s 1n e 4 s n e 4 SOld Que OJUOD uogeesul gN Que 01 U09 SUOI NEDAl SISSBYD sapo9 daag Ayayes 10113 SOIG uo1 onpou u Ayayes 918 S Ayayes ayers 1 911 99 3 MAIAIOAQ MAIAIOAQ MAIAIBAQ soolpuaddy unoy dny
43. Remove Use your thumbs to gently push each release tab outward to free the DIMM from the slot SUPERSERVER 5011H 5011E Manual 5 7 Adding PCI Cards 1 32 bit PCI slot The P3TSSR P3TSSE has four 32 bit MHz 5V PCI slots available A riser card designed specifically for using this slot in a 1U rackmount chassis is included with your system This riser card allows an installed PCI card to sit at a 90 degree angle so it can fit inside the chassis This riser card accommodates 32 bit 33 MHz 5V PCI cards Figure 5 6 shows the riser card Figure 5 6 32 bit 33 MHz 5V Riser Card 2 PCI card installation Before installing a PCI add on card locate the PCI riser card mentioned in Step 1 Begin by removing the I O shield for the PCI slot you wish to populate Fully seat the PCI card into the riser card and screw it into the metal retention rail shown in Figure 2 5 Then insert the riser card into the PCI slot on the motherboard pushing down with your thumbs evenly on both sides of the card See Figure 5 6 for location Finish by using a screw to secure the top of the card shield to the chassis The I O shield protects the motherboard and its components from EMI and aid in proper ventilation so make sure there is always a shield covering each PCI slot Chapter 5 Advanced Motherboard Setup Figure 5 7 Adding PCI Cards PCI Riser Card CPU Socket Memory Modules 5011H P3TSSR Motherboard PCI
44. Riser Card CPU Socket 5011E P3TSSE Motherboard 5 9 SUPERSERVER 5011H 5011E Manual Figure 5 8 Super P3TSSR Layout not drawn to scale JAA 8 7 J30 JPWAKE J29 KB Mouse CPU FAN ATX POWER Ol a EE An 55 O Uepon R com1 PIII FCPGA or a Celeron Processor a o x oi Z VGA GMCH a a a LAN 1 CHFAN1 LAN 2 z lt BATTERY c w z o g D AGP 4x n Se 8 OH FAN E JP35 PCI 1 ae gt a ICH2 ao 8 N e SE gpu E PCI 2 JP36 CO Q W 8 JP31 CH B J26 BIOS PCI 3 FWH An J18 JA2 D PCI4 z JA3 H 2 TI a 5 JP34 S prd KA o UI s l 2 2 ro g 2 5 S AIC 7899 T Jg F i JL1 JBT1 WOL JP32 TOES JPAT CoC ar JWOR 5 10 Chapter 5 Advanced Motherboard Setup P3TSSR Quick Reference for 5011H Default Setting Pins 1 2 Normal Open Terminated Open Terminated Both Pins 1 2 Auto Closed Enabled Pins 1 2 Enabled Closed Enabled Closed Speaker Pins 1 2 Disabled COM1 COM2 Serial Port Connector Jumpers Description JBT1 CMOS Clear JPA1 SCSI Channel A Termination J
45. S Power On Suspend state While the system is in this state the CPU is not executing instructions all power resources that supply system level reference of SO are off system memory context is maintained devices that reference power resources that are on are on and devices that can wake up the system can cause the CPU to continue to execute from where it left off Suspend Time Out This option specifies the length of system inactivity while in the standby state that should expire before the computer enters a suspend power state The settings are Disabled 1Min 5Min and 10Min Power Button Mode This option specifies how the external power button on the computer chas sis functions When set to On Off depressing the power button turns the computer on or off When set to Suspend depressing the power button places the computer in Suspend mode or Full On power mode The Standby setting places the computer in Standby or Full On mode After G3 Enable This option allows AfterG3 Enable support The settings are Disabled and Enabled Disabled prevents the system to power on after power is applied to the system Enabled allows the system to power on after power is applied to the system This means that if an ATX compliant power supply is turned hard off or unplugged from the wall power socket supplying it power the computer system will not power back on immediately after the power cord is reattached or the hard off switch is flipped back on
46. SERVER 5011H 5011E Manual ATX PS 2 Keyboard and PS 2 Mouse Ports PS 2 Keyboard and Mouse Port Pin Definitions The ATX PS 2 keyboard and the 430 PS 2 mouse are located on J30 an e Number Definition See the table on the right for pin 1 Data definitions The mouse port is S Deh above the keyboard port See Fig eer ure 5 8 6 NC LAN1 LAN2 Ports Two Ethernet ports designated LAN1 and LANZ are located be side the VGA port on the I O backplane These ports accept RJ45 Ethernet Port RJ45 type cables Two LEDs on each indicate a successful con nection yellow and activity green Wake On Ring Wake on Ring Pin Definitions JWOR The Wake on Ring JWOR header allows your computer to receive and be woken up by an incoming l Saba call when in the suspend state 2 Wake up Refer to the table on the right for pin definitions The P3TSSR P3TSSE meets the PCI 2 2 stan dard which provides the PME function to support WOR and WOL You must also have a WOR card and cable to use WOR Pin Number Definition Chapter 5 Advanced Motherboard Setup Wake On LAN Wake On LAN Pin The Wake On LAN WOL header pone WOL allows the system to be woken up Pin SCH 7 r Number Definition upon receiving an appropriate sig 1 5V Standby nal via the LAN You must enable Week ake up the LAN Wake Up setting in BIOS to use this feature and hav
47. SUPER SUPERSERVER 5011H 5011E SuperServer 5011H ECH r pr 1 rf Set U Esseg E dessert TS ue SI 5S eg Jl Wl 0 Jl es e C SuperServer 5011E E 0 SS SE ae ol 2 USER S MANUAL Revision 1 0a The information in this User s Manual has been carefully reviewed and is believed to be accurate The vendor assumes no responsibility for any inaccuracies that may be contained in this document makes no commitment to update or to keep current the information in this manual or to notify any person or organization of the updates Please Note For the most up to date version of this manual please see our web site at www supermicro com SUPERMICRO COMPUTER reserves the right to make changes to the product described in this manual at any time and without notice This product including software if any and documentation may not in whole or in part be copied photocopied reproduced translated or reduced to any medium or machine without prior written consent IN NO EVENT WILL SUPERMICRO COMPUTER BE LIABLE FOR DIRECT INDIRECT SPECIAL INCIDENTAL SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES IN PARTICULAR THE VENDOR SHALL NOT HAVE LIABILITY FOR ANY HARDWARE SOFTWARE OR DATA STORED OR USE
48. Serial Port2 Address 2F8 Serial Port2 Mode Normal Parallel Port Address 378 Parallel Port Mode ECP ECP Mode DMA Channel 3 Parallel Port IRQ 7 Power Loss Control Always Off Keyboard Wake up Function Space Select Screen TL Select Item Change Optio Fl General Help F10 Save and Exit ESC Exit V02 03 C Copyright 1985 2000 American Megatrends Inc The Super IO Configuration includes the following items Serial Port 1 Address This option specifies the base I O port address and Interrupt Request ad dress of serial port 1 The settings for this item include Disabled 3F8 IRQ4 3E8 IRQ4 and 2E8 IRQ3 Select the desired setting and then press Enter Serial Port 2 Address This option specifies the base I O port address and Interrupt Request ad dress of serial port 2 The settings for this item include Disabled 2F8 IRQ3 3E8 IRQ4 and 2E8 IRQ3 7 6 Chapter 7 AMIBIOS Serial Port2 Mode This option specifies Serial Port2 Mode The settings for this item include Normal IRDA1 6ms IRDA311 6 ASKIR ASKIR500 ASKIRDem ASKIRD500 Parallel Port Address This option specifies the I O address used by the parallel port The settings for this item include Disabled 378 278 and 3BC Select your setting and then press Enter Parallel Port Mode This option specifies the parallel port mode The settings for this item include Normal Bi directional EPP and ECP ECP Mode DMA Channel This option allows t
49. around at 0 0 and finding the total system memory size next The memory wraparound test is done Memory size calculation has been done Writing patterns to test memory next The memory pattern has been written to extended memory Writing patterns to the base 640 KB memory next Patterns written in base memory Determining the amount of memory below 1 MB next The amount of memory below 1 MB has been found and verified Determining the amount of memory above 1 MB memory next The amount of memory above 1 MB has been found and verified Checking for a soft reset and clearing the memory below 1 MB for the soft reset next If this is a power on situation going to checkpoint 4Eh next The memory below 1 MB has been cleared via a soft reset Clearing the memory above 1 MB next The memory above 1 MB has been cleared via a soft reset Saving the memory size next Going to checkpoint 52h next The memory test started but not as the result of a soft reset Displaying the first 64 KB memory size next The memory size display has started The display is updated during the memory test Performing the sequential and random memory test next The memory below 1 MB has been tested and initialized Adjusting the displayed memory size for relocation and shadowing next The memory size display was adjusted for relocation and shadow ing Testing the memory above 1 MB next The memory above 1 MB has been tested and initialized Saving the memory size inf
50. as splejag GIE Ayayes a2pLa1ul pue solig sisseyug paeoqiayjioW wa sis wajsks uoleyjeysuy uolonposjyuy a v ddy zduo gduo du pduo edyo zduo dyo uoljeziuebic enuen SUPERSERVER 5011H 5011E Manual Table of Contents Preface About THIS Manual sicevscrcesecscesticstennceasenpeetveantectcsvensceuschvenreteeceticetenveensenpeenviendeviesenscerss iii Marital ele DE LEET iii Manual Organization Flowchart cc eeeeceeseeseeeeeneeeeeeeeeeeeaesaeeaeeeseeseeeeeesaeeateneeaeees v Chapter 1 Introduction to the SuperServer 5011H 5011E EN b oe 1 1 1 2 Server Chassis Features 1 2 1 3 Mainboard Features 00 naiea nei a e 1 4 1 4 Contacting Supermicro oo eee eeteeeeeteeeeeeeeeeeeaecaetaeeaecseeeeeeeeeateaeeaeeaeeeseeteas 1 7 Chapter 2 Server Installation E We TEE 2 1 2 2 Unpacking the SuperServer 5011H 5011E oe eeeeeeeeeeeeneeeeeeeeeeeeeeeeee 2 1 2 3 Preparing for Setup oe eececeeceeceeseeseeeeceeeeeeeeeeeeeeeeaesaesaeeeeeeeeeaeeaeeaetereeeeeeees 2 1 Choosing a Setup Location 2 2 Rack Precautions siniseen iiai araisa ieira 2 2 Server Brecautlong 20 EENS 2 2 2 4 Installing the SuperServer 5011H 5011E into a Rack eerste 2 3 Identifying the Sections of the Rack Halle 2 3 Installing the Chassis Rails cceeeseeeeeeceeeeeeseeneeeeeeeseeeeeeeeeeeneeaees 2 4 Installing the Rack Rails oo ec sees eeee eee eeeeseaeteaeseaeseaeeeaeeneeeed 2 4 Installing the Server into the Rack 0 ee seeeeeeeree
51. ce are Removeable Device Hard Drive ATAPI CDROM Onboard LAN1 option and Onboard LANZ option 7 33 SUPERSERVER 5011H 5011E User s Manual 2nd Boot Device The settings for the 2nd Boot Device are Removeable Device Hard Drive ATAPI CDROM Onboard LAN Option and Onboard LANZ Option 3rd Boot Device The settings for the 3rd Boot Device are Removeable Device Hard Drive ATAPI CDROM Onboard LAN1Option and Onboard LANZ Option Hard Disk Drives Use this screen to view the hard drives that have been auto detected or entered manually on your system Removeable Devices Use this screen to view the removeable devices that have been auto de tected or entered manually on your system ATAPI CDROM Drives Use this screen to view the ATAPI CDROM drives that have been auto detected or entered manually on your system 7 34 Chapter 7 AMIBIOS 7 9 Security Setup Choose Security Setup from the AMIBIOS Setup main menu All Security Setup options are described in this section The Security Setup screen is shown below BIOS SETUP UTILITY Main Advanced Chipset PCIPnP Power Boot Security Exit Install or Change the Supervisor Password Not Installed password User Password Not Installed gt gt gt Change Supervisor Password Change User Password Clear User Password Boot Sector Virus Protection Disabled Select Screen Select Item Go to Sub Scree General Help Save and Exit Exit V02
52. considered to be Legacy mode It is used to log interrupt events to operating systems that do not support ACPI Advanced Configuration and Power Interface and operating systems that do Timer Overflow Enable This allows the system to generate a System Management Interrupt after a specific amount of time has passed The settings for this option are Dis abled and Enabled Thermal SMI Enable This allows the system to generate a System Management Interrupt after a specific temperature has been exceeded The settings for this option are Disabled and Enabled PME SMI Enable This allows the system to generate a System Management Interrupt after a Power Management event has ocurred The settings for this option are Disabled and Enabled SW SMI Timer Enable The settings for this option are Disabled and Enabled 7 31 SUPERSERVER 5011H 5011E User s Manual TCO Logic SMI Enable This allows the system to generate a System Management Interrupt when a century rollover occurs The settings for this option Disabled and Enabled RTC Resume This allows you to direct the system to resume operation at a predetermined time by using the real time clock The settings for this option Disabled and Enabled RTC Alarm Date This allows you to input the date you want the system to resume operation according to a real time clock wake up Input a number from 1 to 31 to indicate the day of the month RTC Alarm Time This allows you to input the t
53. d floppy drives you will need to remove the top chassis cover The SCSI disk drives can be installed and removed from the front of the chassis without removing the top chassis cover 2 Installing a CD ROM and floppy disk drives Refer to Section 6 4 if you need to reinstall a CD ROM and or floppy disk drive to the system 3 Check the SCSI disk drives 5011H Depending upon your system s configuration your system may have one or two SCSI drives already installed If you need to install SCSI drives please refer to Section 6 4 4 Check the airflow Airflow is provided by a 10 cm input fan and one optional 4 cm cooling fan The system component layout was carefully designed to promote sufficient airflow through the small 1U rackmount space Also note that all power and data cables have been routed in such a way that they do not block the airflow generated by the fans 5 Supplying power to the system The last thing you must do is to provide input power to the system Plug the power cord from the power supply unit into a high quality power strip that offers protection from electrical noise and power surges It is recommended that you use an uninterruptible power supply UPS 2 10 Chapter 3 System Interface Chapter 3 System Interface 3 1 Overview There are several LEDs on the control panel as well as others on the SCSI drive carriers and the motherboard to keep you constantly informed of the overall status of the system as
54. dapter to be the primary video device at bootup External PCI This setting allows a PCI Display Adapter card to be the primary video device at bootup External AGP This setting allows an AGP Display Adapter to be the primary video device at bootup 7 16 Chapter 7 AMIBIOS Internal Graphics Mode Select This option selects the mode for the internal graphics mode Settings in clude Disabled Enabled 512 KB and Enabled 1 MB Enabled 1MB This option allows the Internal Graphic controller to allocate 1 MB of system memory for video display use Enabled 512KB This option allows the Inter nal Graphic controller to allocate 512 KB of system memory for video dis play use Disabled This option allocates no system memory for video dis play use Display Cache Window Size This option sets the size of the display cache window The settings are 64 MB and 32 MB Display VBIOS Message This option allows the BIOS to display VBIOS messages The settings are Enabled or disabled Internal Graphics Scaling This option allows the Internal Graphics Scaling to be manually set or auto matically set The settings for this option for this setting include Disabled Auto and Enabled Auto This setting allows the Internal Graphics scaling to auto select itself This setting sets the Internal Graphics scaling off Enabled This setting sets the Internal Graphics scaling on AGP Graphics Aperture Size This option allows you to adjust
55. e a LAN card with a Wake on LAN connector and cable Refer to the table on the right for pin defini tions Chassis Intrusion Chassis Intrusion Pin Definitions s i JL1 The Chassis Intrusion header is i In located on JL1 See board layout Number Definition for the location See the table on CT A the right for pin definitions 2 Ground SUPERSERVER 5011H 5011E Manual 5 9 Jumper Settings Explanation of Connector pee CT Te Te To modify the operation of the motherboard jumpers can be used to choose between optional set tings Jumpers create shorts be tween two pins to change the seed function of the connector Pin 1 is Setting Te BE identified with a square solder pad Pin 1 2 short on the printed circuit board See the motherboard layout pages for jumper locations Jumper Cap LI Note Closed refers to the jumper being set over both pins on a two pin jumper header Open refers to the jumper being set over a single pin of a two pin jumper Front Side Bus Speed The FSB speed is set with JP11 Front Side Bus Speed Jumper Settings JP11 JP12 and JP12 The table on the right displays the settings for these two JP11 JP12 FSB Speed jumpers The CPU speed can also Se E Ke be changed by software control in ies E he Se D BIOS see CPU Speed setting S s Note The Auto setting allows the CPU to The CPU Speed setting will show set the speed you t
56. e sure your computer chassis provides ex cellent conductivity between the power supply the case the mounting fasteners and the motherboard Unpacking The motherboard is shipped in antistatic packaging to avoid static damage When unpacking the board make sure the person handling it is static pro tected SUPERSERVER 5011H 5011E Manual Figure 6 1 Chassis Front View Control Panel Slim CD ROM Drive System LEDs G JI Yes e IDE Drives System Reset Rack Unit Retention Floppy Drive Main Power Screws 3 each side Ie 0 0 U SCSI Drives Figure 6 2 Chassis Rear View PCI Card Release Latch PCI Slot External SCSI Connector 6 2 Control Panel The control panel located on the front of the chassis must be connected to the JF1 connector on the motherboard to provide you with system control buttons and status indicators These wires have been bundled together in a ribbon cable to simplify the connection Connect the cable
57. eceeseeeeeeeeeeenesneeseseseeeneeatees Table of Contents IDE Configuratio Misena AAR AEA Ae 7 8 Floppy Configuration ececescseeecseeeseeseeneceeseeeeeseeseeeeeeeeesaeeaeeaeeeeseetens 7 11 Boot Settings Configuration oo ee ececeseeseseeseeeeeceeseeeeseeseeaeeeeeeeeeeeeeees 7 12 Event Log Configuration 7 5 Chipset Gen ege ee LEET GMCH Configuration 0 ee eeeeseeeeeeeceeeeeceeceeeeeeeeeeeseeeaesareeseeeeseeteats IGH2 Configuration EEN raisin scintaestdiesteheaieees 726 PCLPNP S tup EE 7 7 ower Setup ee a ea piir T8 lee EE EE Boot Device Priority icccsecsccciscesccsscsusnssrescestsdeccusesstsnsrsovesstseesacencoaseatenssvees Hard DISK Drives ees Removable Devices ATAPI CD ROM DI ives cceeeeceeeeeeeeeceeeeeeeeeaeeaeeeeseeeeeseaeeaeeaesaeeneeeeeees 7 29 S Curity Setup six kincaid eae At eles Supervisor Passwordis eseou Seer ei User PassWord EE Change Supervisor Password ccceseeeeeeeeeseeeeeeeeeeeeeeeneeneeeeeenees 7 36 Change User Password ceceeseecesceeeeeeneeeeeeeceeseeeeaseaeeeeateeeeereeeees 7 36 Clear User Password AE 7 36 Boot Sector Virus Protectlon cee cecseceeseesceseeeeceeeeeeeeeeseseeeaeeseeeeesees 7 36 7 10 Exit Setup Exit Saving Changes eceeeeeeeeeeeeeeeeeeeeeecaeeeseeseeeeeeeeesaeeaesaeeeeeeeees 7 37 Exit Discarding Changes AE 7 37 Load Optimal Defaults ee nniatenisenvanenannenies 7 38 Load Fail Safe Defaults 0 0 cece cecceseeseeseeneeeeceeeeeceeeea
58. echnology that is closely associated with the S3 state of the ACPI Advanced Configuration and Power Interface speci fication STR allows a properly configured system to go into a low power state while saving information to main memory about the system s configu ration open applications and active files While in the low power STR state memory remains powered to retain the system information while most other components turn off to conserve energy Fans are turned off to pro vide silent operation and to minimize power consumption Properly config ured systems in STR typically can consume less than 5 watts Repost Video on S3 Resume This option determines whether or not to invoke the VGA BIOS post test when resuming from STR or the S3 state Settings are No and Yes Used with ACPI only Power Management APM This option allows you to select using APM Advanced Power Manage ment The settings are Disabled and Enabled Standby Time Out This option specifies the length of system inactivity time that should expire before the computer enters a standby power state The settings are Dis abled 1Min 5Min and 10Min 7 28 Chapter 7 AMIBIOS Suspend Power Saving Type The settings for this option are C2 and S1 The C2 setting allows the CPU microprocessor to be put in a low power state In this state incoming interrupts wake up the CPU microprocessor to process them I O APIC S1 allows the system to enter the S1 PO
59. eck with your adapter card manuals first before modifying the default settings in the BIOS PCI IDE BusMaster The settings for this option are Disabled and Enabled This option is only available on non Microsoft Operating Systems OffBoard PCI ISA IDE Card This option specifies which PCI slot has an IDE controller card installed Settings are Auto PCI slot 1 PCI slot 2 PCI slot 3 PCI slot 4 PCI slot 5 and PCI slot 6 PCI slot numbers will be available in this option even if your motherboard does not have that slot number If your motherboard does not have a PCI slot 5 for example do not set this option to PCI slot5 OffBoard PCI Primary IRQ This option specifies the primary IRQ for the PCI Settings include Disabled INTA Interrupt A INTB INTC INTD and Hardwired Hardwired tells the BIOS that the OffBoard IDE Primary controller is a legacy device and the interrupt request channels cannot participate in PCI Swizzle PCI Swizzle is a term used to describe IRQ sharing USB Function The settings for this option are Disabled and Enabled Disabled prevents the use of the USB ports and Enabled allows the use of the USB ports 7 24 Chapter 7 AMIBIOS Legacy USB Support This option allows Legacy USB support The settings are Disabled En abled and Auto Disabled prevents the use of any USB device in DOS or during system boot Enabled allows the use of USB devices during boot and while using DOS The
60. ed Enabled and Cached WP When Disabled the contents of the video ROM are not copied to RAM When Enabled the contents of 16 KB of video ROM beginning at the above address are copied shadowed from ROM to RAM for faster application When set to Cached WP the contents of 16 KB of video ROM beginning at the above address are copied shadowed from ROM to RAM and can be written to or read from cache memory The settings for this option are Disabled Enabled and Cached WP The optimal settings are Cached WP for C000 and C400 and Disabled for all the other settings 7 22 Chapter 7 AMIBIOS 7 6 PCI PnP Setup Choose PCI PnP Setup from the AMIBIOS Setup main menu All PCI PnP options are described in this section The PCI PnP Setup screen is shown below BIOS SETUP UTILITY Main Advanced Chipset PCIPnP Power Boot Security Exit No lets the BIOS Plug amp Play O S configure all the Reset Config Data devices in the system PCI Latency Timer Yes lets the Allocate IRQ to VGA operating system Palette Snooping configure Plug and PCI IDE BusMaster Play PnP devices not OffBoard PCI ISA IDE Card required for boot if OffBoard PCI IDE Primary your system has a Plug IRQ and Play operating OffBoard PCI IDE Secondary system IRQ USB Controller Enabled Select Screen Legacy USB Support Disabled Select Item Change Option PCI Slot1 IRQ Preference Available General Help PCI Slot2 IRQ Preference Available Save and Exit P
61. ed on pins 13 and 14 of JF1 This provides an indica tion of IDE disk activity on the con trol panel Refer to the table on the right for pin definitions and Fig ure 5 1 for pin locations Power LED The Power LED connection is lo cated on pins 15 and 16 of JF1 When illuminated this LED indi cates that power is applied to the system There is also an alternate 3 pin header for the Power LED located at J50 You only need to use connection that on JF1 is de signed for Supermicro chassis See the tables on the right for pin definitions and Figure 5 1 for pin locations Universal Serial Bus USB Two External Universal Serial Bus connectors USBO and USB1 are located on the motherboard backplane In addition two inter nal USB headers USB2 USB3 are located on J43 J51 Refer to the tables on the right for pin defi nitions 5 16 HDD Defi LED Pin nitions JF1 Pin Number Definition 13 14 5V HD Active Power LED Pin De J finitions F1 Pin Number Definition 15 16 Power Control Power LED Pin Definitions J50 Pin Number Definition 1 Control 2 D 3 Power Universal Serial Bus Pin Definitions USBO Pin Pin Number Definition Number Definition 1 5V 1 5V 2 Po 2 Po 3 PO 3 PO 4 Ground 4 Ground USB2 USB3 Pin Pin Number Definition Number Definition 1 5V 1 5V 2 Po 2 Po 3 PO
62. eeeeeeeeeeeeeesneeeeeeeeeaees 2 5 Installing the Server into a Telco Rack o cee eeeseeeeeeeeteeteeteeneeees 2 6 2 5 Checking the Motherboard Setup D 2 6 Checking the Drive Bay Setup cc eeceeeeeeseceeeeeeeeeseeeneceeeeeeeaeeaeeereaeeaes Chapter 3 System Interface B21 e TEE 3 1 3 2 Control Panel Buttons ou ccc cccccccsseccssseccsseceesseccsseeecseecesseeccsseecseesesseeceseeees 3 1 vi Table of Contents ae EE 3 3 3 4 SCSI Drive Carrier LEDS G0o11H eseeneeeeeeeeeeeeeeteeeaeteeseeneeeeeeeees 3 3 3 5 Power Supply Switch dog dni nie ai eae Medics 3 3 3 6 Motherboard LEDs Chapter 4 System Safety 4 1 Electrical Safety Precautions 0 0 cece eeeeeeeeeeeeeeeeeeeeeeeaeeesaeeeeseeeeeeneeatee 4 1 4 2 General Safety Precautions 0 eecceececeeeeeseeeeeseeeeceeeeaeeseeaeeseseeeeeeeeeateas 4 2 4 3 ESD Precautions ccc saceeacevianndenearencavestatavengentarevlenavtiveaverite 4 3 Chapter 5 Advanced Motherboard Setup 5 1 Handling the PSTSSR P3TSSE Motherboard AA 5 1 5 2 Motherboard Installation ccccsccscessccscesseesseccscesseesssecseesteestecsseesseeseecoser 5 3 Connecting Cables oe ceceeseeseeneeeeeeeeeeeeeeeeetaeeeeeeeeeeeeeeeesaeeaeseeneseeteaeeeeateas Connecting Data Cables Connecting Power Cables cecececcesceseeeeeeeseeeeeceseeseeeeaeeeeeeseeeeeeaeeaes 5 3 Connecting the Control Panel 5 4 BA e EI LEE EE 5 5 5 5 Installing Processors anneo Aniani A RRN A RRN A 5 5 5 6 Installing MeOM
63. eeseeaeseseeeeeteeeeateas 7 38 Discard Rei ue TEE 7 38 Appendices Appendix A BIOS Error Beep Codes and Messages ececceseeseereeteereereeeees A 1 Appendix B AMIBIOS POST Checkpoint Codes sesser B 1 Appendix C List of Figures Appendix D System Specifications 0 cee eeceeeeeeseeeeeeeeeeceeeeeeeeeeaeeeeeeeeeeeseaeeas D 1 SUPERSERVER 5011H 5011E User s Manual NOTES Chapter 1 Introduction Chapter 1 Introduction to the SuperServer 5011H 5011E 1 1 Overview The Supermicro SuperServer 5011H 5011E is a high end single processor 1U rackmount server that features some of the most advanced technology currently available The SuperServer 5011H 5011E is comprised of two main subsystems the SC810 1U rackmount chassis and the P3TSSR for 5011H or P3TSSE for 5011E single 370 pin Pentium III FCPGA or Celeron FCPGA PPGA processor mainboard Please refer to our web site for infor mation on operating systems that have been certified for use with the SuperServer 5011H 5011E www supermicro com In addition to the mainboard and chassis various hardware components may have been included with your SuperServer 5011H 5011E as listed below D One 1 370 pin Pentium III FCPGA or one Celeron FCPGA PPGA proces sor One CPU heat sink e Up to 512 MB SDRAM non ECC supported non registered main memory J One 1 1 44 floppy drive D One 1 slim CD ROM drive D One 1 SCA SCSI backplane 5011H only D
64. emperature Range 0 to 40 degrees C D 1 SUPERSERVER 5011H 5011E Manual Humidity Range 5 90 non condensing Safety Regulations UL 1950 CUL TUV EMI FCC part 15 CISPR 22 EN 55022 Cooling Fans System One 1 10 cm ball bearing blower fan Onboard Fan Headers One 1 CPU two 2 chassis and two 2 overheat fan headers max current 035 amps ea or 1 2 amps set of four Form Factor P3TSSR P3TSSE motherboard ATX SC810 chassis 1U rackmount Operating Systems Supported Windows NT Windows 2000 Solaris Netware SCO UNIX and Linux Dimensions 16 7 x 1 7 x 22 7 in 425 x 44 x 560 mm W x H x D Weight Net Full System 26 Ibs 11 8 kg Gross Full System 32 Ibs 14 5 kg Regulations FCC Class B CE UL TUV VK 240 4 7G AA Tht thrice pepi eth Fei 12 of he FOE SUPER MICRO COMPUTER INC MODEL SuperServes STIH Ut ule G2 C 3 Der Capea r puis Eat rn bylem iaa ri UU Ben eiria my w cae aerial mierky ard T Hep enny ep ad ety eke Gre sei phm pipka pag Pud tay ae ed ee
65. er supply connec Pin Number Definition Pin Number Definition tor on the P3TSSR P3TSSE is des ee a SEN ignated ATX POWER This is a 20 3 Ground 13 Ground pin connector Attach an ATX Ges CA ae Se power supply cable to J29 by Ge 2 SE roun roun aligning the tab on the connector 8 PW OK 18 5V Refer to the table on the right for e Se Es REN pin definitions Infrared Connector Infrared Pin Definitions The infrared connectors are lo 345 cated on pins 1 5 of J45 for the Pin RS Number Definition P3TSSR P3TSSE Refer to the 1 5V table on the right for pin defini S le tions See the Technical Support S KE section of our web page for infor 6 NC mation on the infrared devices you S NC indicates No Connection can use with this connector PWR_ON PWR Button Pin Definitions The PWR_ON connection is lo JF1 cated on pins 1 and 2 of JF1 This Pin o Number Definition connector attaches to the Power 1 PW_ON button on the control panel which Eer allows you to turn on and off the power to the system The user can also configure this button to function as a suspend button see the Power Button Mode set ting in BIOS To turn off the power when set to suspend mode hold down the power button for at least 4 seconds Refer to the table on the right for pin definitions and Figure 5 1 for pin locations 5 14 Chapter 5 Advanced Motherboard Setup Reset Reset Button Pin Definitions The Reset connection is
66. erface test command next The keyboard controller interface test completed Writing the com mand byte and initializing the circular buffer next The command byte was written and global data initialization has completed Checking for a locked key next Locked key checking is over Checking for a memory size mismatch with CMOS RAM data next The memory size check is done Displaying a soft error and checking for a password or bypassing WINBIOS Setup next The password was checked Performing any required programming before WINBIOS Setup next The programming before WINBIOS Setup has completed Uncompressing the WINBIOS Setup code and executing the AMIBIOS Setup or WINBIOS Setup utility next Returned from WINBIOS Setup and cleared the screen Performing any necessary programming after WINBIOS Setup next The programming after WINBIOS Setup has completed Displaying the power on screen message next The first screen message has been displayed The lt WAIT gt message is displayed Performing the PS 2 mouse check and extended BIOS data area allocation check next Programming the WINBIOS Setup options next The WINBIOS Setup options are programmed Resetting the hard disk controller next The hard disk controller has been reset Configuring the floppy drive controller next The floppy drive controller has been configured Configuring the hard disk drive controller next B 6 Appendix B AMIBIOS POST Checkpoint Codes Checkpo
67. es are mounted in drive carriers to simplify their installation and removal from the chassis These carriers also help promote proper airflow for the SCSI drive bays For this reason even empty carriers without SCSI drives installed must remain in the chassis To add a new SCSI drive install a drive into the carrier with the printed circuit board side toward the carrier so that the mounting holes align with those in the carrier Secure the drive to the carrier with four screws as shown in Figure 6 4 Figure 6 4 Mounting a SCSI Drive in a Carrier 5011H only Use caution when working around the SCSI backplane AN Do not touch the backplane with any metal objects and make sure no ribbon cables touch the backplane or obstruct the holes which aid in proper airflow are installed both SCSI drive carriers must remain in Important Regardless of how many SCSI hard drives AN the drive bays to maintain proper airflow SUPERSERVER 5011H 5011E Manual 2 __Installing removing hot swap SCSI drives Two SCSI drive bays are located in the front of the chassis making them easily accessible for installation and removal These SCSI drives are hot swap units meaning they can be installed and removed without powering down the system To remove first push the release button located beside the drive LEDs then swing the colored handle fully out and use it to pull the unit straight out see Figure 6 5 Handle Release Button Fig
68. fully loaded When lifting the system two people at either end should lift slowly with their feet spread out to distribute the weight Always keep your back straight and lift with your legs Place the chassis top cover and any system components that have been removed away from the system or on a table so that they won t accidentally be stepped on While working on the system do not wear loose clothing such as neckties and unbuttoned shirt sleeves which can come into contact with electrical circuits or be pulled into a cooling fan Remove any jewelry or metal objects from your body which are excellent metal conductors that can create short circuits and harm you if they come into contact with printed circuit boards or areas where power is present After accessing the inside of the system close the system back up and secure it to the rack unit with the retention screws after ensuring that all connections have been made 4 2 Chapter 4 System Safety 4 3 ESD Precautions A Electrostatic discharge ESD is generated by two objects with different electrical charges coming into contact with each other An electrical discharge is created to neutralize this difference which can damage electronic components and printed circuit boards The following measures are generally sufficient to neutralize this difference before contact is made to protect your equipment from ESD Use a grounded wrist strap designed to prevent sta
69. he COM2 port is a header on mouse keyboard ports 5 5 Installing Processors UO Ports LAN1 LAN2 VGA Graphics Port Blue the motherboard located behind the pressure to the top of the pro Avoid placing direct cessor package Always connect the power cord last and always remove it before adding removing or changing any hardware components 1 Installing the FCPGA processors The P3TSSR P3TSSE has one 370 pin socket which supports Intel Pentium II FCPGA and Celeron FCPGA PPGA processors Lift the lever on the FCPGA socket and insert the processor with the heat sink attached keep ing the notched corner oriented toward pin one on the socket Make sure the processor is fully seated in the socket and and then close the lever See Figure 5 3 for views of a 370 processor installation pin FCPGA socket before and after SUPERSERVER 5011H 5011E Manual 2 Attaching heat sinks to the processors One passive heat sink has been included with your SuperServer 5011H 5011E Secure the heat sink to the processor with a suitable thermal compound to best conduct the heat from the processor to the heat sink Make sure that you apply the compound evenly on the CPU s die and that good contact is made between the CPU chip the die and the heat sink Insufficient contact inproper types of heat sink or inproper amount of thermal compound can cause the processor to overheat which may crash the system Refer to Figure 5 4 fo
70. he actual CPU speed for each FSB speed option selected Note If the system does not reboot after changing the CPU speed 1 clear CMOS and reboot as described on the next page and then 2 set the correct CPU speed with the BIOS setting men tioned above 5 20 Chapter 5 Advanced Motherboard Setup CMOS Clear CMOS Clear Jumper Settings JBT1 Refer to the table on the right for Jumper ee setting JBT1 to clear CMOS Al Position RE ways remove the AC power cord 2 3 CMOS Clear from the system before clearing CMOS Speaker Enable Disable Speaker Enable Disable JP32 JP32 allows you to enable or dis Open Disabled able the onboard speaker Refer Closed Enabled to the table on the right for jumper settings LAN1 LAN2 Enable Disable LAN1 LAN2 Jumper Settings Change the setting of jumper JP35 JP35 JP31 and JP31 to enable or disable LAN 1 Ger G ft osition efinition and LAN 2 respectively Refer to Open Enabled the table on the right for jumper set See Disabled tings Note You must disable LAN1 to use an add on card in PCI 4 Keyboard Wake Up Keyboard Wake Up i i Jumper Settings The JPWAKE jumper is used to ENAKE gether with the Keyboard Wake Up Jumper function in BIOS Enable both the Position Definition R 1 2 Disabled jumper and the BIOS setting to al 2 3 Enabled low the system to be woken up by depressing a key on the
71. he user to set the setting for the ECP Mode of the DMA Channel The settings for this item include 0 1 and 3 Parallel Port IRQ This option allows the user to set the Parallel Port IRQ The settings for this item include 5 and 7 7 7 SUPERSERVER 5011H 5011E User s Manual Power Loss Control This option determines how the system will react when power is reapplied after being lost unexpectedly The settings are Always Off if the system loses power unexpectedly the computer system will keep power off until the power button is pressed Always On if the system loses power unex pectedly the computer system will restore power and Previous if the system loses power unexpectedly the computer system restores the sys tem to its previous state before power was lost Keyboard Wake Up Function Use this option to specify which key is to be depressed to wake up the system from sleep mode The settings are Disabled CTRL F1 Space and Any Key Disabled This setting prevents the computer system from using the keyboard to power it on Ctrl F1 This setting allows the computer system to be powered on when the CTRL and F1 keys on the keyboard are pressed Space This setting allows the computer system to be powered on when the Space bar on the keyboard is pressed This is the default setting Any Key This setting allows the computer system to be powered on when any keys on the keyboard are pressed IDE Configuration Onboard PCI IDE
72. if available is initialized Next beginning the base 512 KB memory test Initializing the interrupt vector table next Initializing the DMA and Interrupt controllers next Enabling the floppy drive controller and Timer IRQs Enabling internal cache memory Initializing the floppy drive Looking for a floppy diskette in drive A Reading the first sector of the diskette A read error occurred while reading the floppy drive in drive A Next searching for the AMIBOOT ROM file in the root directory The AMIBOOT ROM file is not in the root directory Next reading and analyzing the floppy diskette FAT to find the clusters occupied by the AMIBOOT ROM file Next reading the AMIBOOT ROM file cluster by cluster The AMIBOOT ROM file is not the correct size Next disabling internal cache memory Next detecting the type of flash ROM Next erasing the flash ROM Next programming the flash ROM Flash ROM programming was successful Next restarting the system BIOS B 2 Appendix B AMIBIOS POST Checkpoint Codes B 3 Uncompressed Initialization Codes The following runtime checkpoint codes are listed in order of execution These codes are uncompressed in F0000h shadow RAM Checkpoint 03h 05h 06h 07h 08h OAh OBh OCh OEh OFh 10h 11h 12h 13h 14h 19h 1Ah 2Bh 2Ch Code Description The NMI is disabled Next checking for a soft reset or a power on condition The BIOS stack has been built Next
73. ime you want the system to resume operation according to a real time clock wake up Input the hour and minutes as desired USB Controller Resume This allows you to wake up the system from a USB device The settings for this option Disabled and Enabled PME Resume This allows you to wake up the system from a PME device The settings for this option Disabled and Enabled RI Resume The settings for this option Disabled and Enabled SMBUS Resume This allows you to wake up the system from a System Management Bus device The settings for this option Disabled and Enabled 7 32 Chapter 7 AMIBIOS LAN Wake Up This allows you to wake up LAN1 and LAN2 from a System Management Bus device The settings for this option Disabled and Enabled 7 8 Boot Setup Choose Boot Setup from the AMIBIOS Setup main menu All Boot Setup options are described in this section The Boot Setup screen is shown below BIOS SETUP UTILITY Main Advanced Chipset PCIPnP Power Boot Security Exit Boot Device Priority Hard Disk Drives Removable Devices ATAPI CDROM Drives Select Screen Select Item Go to Sub Scree General Help Save and Exit Exit V02 03 C Copyright 1985 2000 American Megatrends Inc Boot Device Priority 1st Boot Device AMI BIOS automatically detects hardware devices of the system This op tion allows the BIOS to specify the order of boot sequence that is auto detected by the BIOS The settings for the 1st Boot Devi
74. int 95h 96h 97h 98h 99h 9Ah 9Bh 9Ch 9Dh 9Eh A2h A3h A4h A5h A7h A8h A9h Aah Abh BOh Bih 00h Code Description Initializing the bus option ROMs from C800 next See the last page of this chapter for additional information Initializing before passing control to the adaptor ROM at C800 Initialization before the C800 adaptor ROM gains control has com pleted The adaptor ROM check is next The adaptor ROM had control and has now returned control to BIOS POST Performing any required processing after the option ROM returned control Any initialization required after the option ROM test has completed Configuring the timer data area and printer base address next Set the timer and printer base addresses Setting the RS 232 base address next Returned after setting the RS 232 base address Performing any required initialization before the Coprocessor test next Required initialization before the Coprocessor test is over Initializing the Coprocessor next Coprocessor initialized Performing any required initialization after the Coprocessor test next Initialization after the Coprocessor test is complete Checking the extended keyboard keyboard ID and Num Lock key next Issuing the keyboard ID command next Displaying any soft errors next The soft error display has completed Setting the keyboard typematic rate next The keyboard typematic rate is set Programming the memory wait sta
75. it 33 MHz 5V Riser Card 5 8 Adding PCI Cards 5 9 SUPER P3TSSR Layout 5 10 SUPER P3TSSE Layout 5 12 Chassis Front and Rear Views 6 2 System Cooling Fans 6 4 Mounting a SCSI Drive in a Carrier 5011H 6 5 Removing SCSI Drives 5011H 6 6 Removing IDE Drives 5011E 6 8 Chassis Rear View 6 10 SUPERSERVER 5011H 5011E Manual Notes C 2 Appendix D System Specifications Appendix D System Specifications Processors One 370 pin Intel Pentium III FCPGA 500 MHz 1 26 GHz or one Celeron FCPGA PPGA 333 866 MHz CPU with a 133 or 100 MHz FSB Memory Capacity 3 DIMM slots to support a maximum of 512 MB SDRAM DIMM Sizes 128 MB 256 MB 512 MB 168 pin SDRAM modules supported SCSI Controller 5011H only Adaptec AIC 7899 for dual channel Ultra160 SCSI SCSI Backplane Controller 5011H only SCA backplane for two 2 SCA hot swap SCSI drives Main Drive Bays 5011H Two 2 drive bays to house two 2 standard 1 80 pin SCA SCSI drives 5011E Two 2 drive bays to house two 2 3 5 x 1 IDE disk drives Peripheral Bays One 1 3 5 floppy drive One 1 slim CD ROM drive PCI Expansion Slot Four 4 onboard 32 bit 33 MHz 5V PCI slots bundled with a 32 bit 33 MHz 5V riser card Power Supply Type 1 x 200W with 3 3V 5V 12V 5V and 12V main DC outputs and a 5V standby output Input Voltage 100 240VAC w 10 tolerance units are auto switching capable Fans Two 4 cm ball bearing fans Operating T
76. keyboard Refer to the table on the right for jumper settings Note Your power supply must meet ATX specifi cation 2 01 or higher and supply 720 mA of standby power to use this feature however you would need 1 5A for the SSR SSE 5 21 SUPERSERVER 5011H 5011E Manual LVD Channel A SCSI Termination LVD CH A SCSI Enable Disable 5011H only Termination Jumper Settings JPA1 Jumper JPA1 allows you to enable or disable Jumper A Position Definition termination for the LVD Channel A SCSI con Open Enabled nector The normal default position is open Closed Disabled to enable SCSI termination See the table on the right for jumper settings LVD Channel B SCSI Termination LVD CHA SCSI Enable Disable 5011H only Termination Jumper Settings JPA2 Jumper JPA2 allows you to enable or disable Jumper termination for the LVD Channel B SCSI con Position Definition pen Enabled nector The normal default position is open Closed Disabled to enable SCSI termination See the table on the right for jumper settings SCSI Enable Disable 5011H only SCSI Enable Disable Jumper Settings JP34 Jumper JP34 allows you to enable Jumper or disable all onboard SCSI The Position Definition i 1 2 Enabled normal default position is en 2 3 Disabled abled See the table on the right for jumper settings Watchdog Reset Watchdog Enable Disable J
77. le connections and airflow Make sure all power and data cables are properly connected and not blocking the airflow See Section 5 3 for details on cable connections Also check the air seals for damage The air seals are located under the blower fan and beneath the frame cross section that separates the drive bay area from the motherboard area of the chassis Note Make sure that the air seals are properly installed 2 7 SUPERSERVER 5011H 5011E Manual Figure 2 5a Accessing the Inside of the SuperServer 5011H with SCSI installed Top Chassis Cover Removed Cover Release H Buttons PCI Riser Card Retention Rail P3TSSR Motherboard gt KA Pe Blower Fan Power Supply CPU Heatsink System Memory SCSI Driv Air Seals Control Panel D ROM Dri c S oe Floppy Drive 5011H 2 8 Chapter 2 Server Installation Figure 2 5b Accessing the Inside of the SuperServer 5011E with IDE installed Control Panel Floppy Drive OM Drive Blower Fan lt gt SS _Z2 lt SED R IDE Drive 5011E 2 9 SUPERSERVER 5011H 5011E Manual 2 6 Checking the Drive Bay Setup Next you should check to make sure the peripheral drives and the SCSI drives 5011H only and SCA backplane have been properly installed and all connections have been made 1 Accessing the drive bays All drives can be accessed from the front of the server For servicing the CD ROM an
78. led Quiet Boot If Disabled this option will cause the normal POST messages to be dis played upon setup When Enabled the OEM logo is displayed instead of the POST messages Add On ROM Display Mode Set this option to display add on ROM read only memory messages The settings for this option are Force BIOS and Keep Current Force BIOS allows the computer to force a third party BIOS to display during system boot Keep Current has the system display AMIBIOS information on bootup BootUp Num Lock This option is used to select the status of the Number Lock function on your keyboard on bootup The settings are On and Off BootUp CPU Speed This option is used set the CPU speed to either High or Low PS 2 Mouse Support This option specifies whether a PS 2 Mouse will be supported Settings are Enabled and Disabled Typematic Rate Set this option to select the rate at which the computer repeats a key that is held down Settings are Fast and Slow Fast This sets the rate the computer repeats a key to over 20 times per second Under normal opera tions this setting should not be changed Slow This sets the rate the computer repeats a key to under 8 times per second 7 12 Chapter 7 AMIBIOS System Keyboard This option is to let the system know if a keyboard is Present or Absent Primary Display This option specifies the type of monitor display you have installed on the system The settings are Absent VGA EGA Color 4
79. located JF1 on pins 3 and 4 of JF1 This con Pin N Definiti nector attaches to the Reset but KEES ton on the control panel which al 4 Ground lows you to reboot the system Refer to the table on the right for pin definitions and Figure 5 1 for pin locations Overheat LED JOH Overheat LED V Pin Definitions Pins 7 and 8 of JF1 are for the JF1 Overheat LED which provides you Pin we Number Definition with advanced warning of chas 7 Power sis overheating This LED will also SE illuminate if the blower fan fails which will cause the chassis tem perature to rise Refer to the table on the right for pin definitions and Figure 5 1 for pin locations NIC1 LED NIC1 LED Pin Definitions The Network Interface Controller 1 WEI LED connection is on pins 11 and Pin 12 of JF1 This header is used to Ge KE display network activity on LAN 12 Control Ethernet port 1 Refer to the table on the right for pin definitions and Figure 5 1 for pin locations NIC2 LED NIC2 LED Pin Definitions The Network Interface Controller 2 JF1 LED connection is on pins 9 and Pin Get 10 of JF1 This header is used to eT eee display network activity on LAN 10 Control Ethernet port 2 Refer to the table on the right for pin definitions and Figure 5 1 for pin locations 5 15 SUPERSERVER 5011H 5011E Manual HDD LED The Hard Disk Drive LED connec tion is locat
80. lus and minus keys to change the option setting The settings are described on the following pages ICH stands for I O Controller Hub which is a chipset on the motherboard that controls the basic UO functions USB ports audio functions modem functions IDE channels and PCI slots Moon ISA Device Enable This option allows a Moon ISA device to be supported The settings are Disabled and Enabled A Moon ISA device is a device that contains an Intel PClset S82380AB PCI to ISA in a 160 pin MQFP chipset This chipset is called an Intel Moon ISA or Intel MISA This chipset is used to connect ISA devices to computers that do not have a physical ISA slot The best example of this is a notebook computer No ISA Slots when used with a docking station contains up to three ISA peripherals The docking station would contain the Intel Moon ISA chipset ICH2 Positive Decode This option allows the ICH2 Positive Decode to be set The settings are Disabled and Enabled CPU Bist Enable This option allows the CPU Bist Enable to be set The settings are Disabled and Enabled ICH2 DCB Enable This option allows the ICH2 DCB to be set The settings are Disabled and Enabled SMBus Controller The settings for this option are Enabled and Disabled 7 20 Chapter 7 AMIBIOS LPC 4Eh 4Fh Decode This option allows the LPC 4Eh 4Fh to be set The settings are Disabled and Enabled DMA 0 Type DMA 1 Type DMA 2 Type DMA 3 Ty
81. m the system as opposed to the power button located on the control panel on the front of the chassis 3 6 Motherboard LEDs e PW Power_On LED There is one PW Power_on LED on the motherboard When illuminated it indicates that system power is present on the motherboard This LED is located in the corner of the P3TSSR P3TSSE near the DIMM2 slot SUPERSERVER 5011H 5011E Manual o DA1 SCSI LED Indicator 5011H only There is one SCSI LED Indicator DA1 on the motherboard When illumi nated it indicates that SCSI is active This SCSI LED DA1 is located near Ultra III LVD Channel A JA1 on the P3TSSR mainboard Chapter 4 System Safety Chapter 4 System Safety 4 1 Electrical Safety Precautions A Basic electrical safety precautions should be followed to protect yourself from harm and the SuperServer 5011H 5011E from damage Be aware of the locations of the power on off switch on the chassis as well as the room s emergency power off switch disconnection switch or electrical outlet If an electrical accident occurs you can then quickly remove power from the system Do not work alone when working with high voltage components Power should always be disconnected from the system when removing or installing main system components such as the motherboard memory modules and IDE and floppy drives When disconnecting power you should first power down the system with the operating system first and then un
82. mounting holes on your motherboard that line up with the standoffs and tighten until snug if you screw them in too tight you might strip the threads Metal screws provide an electrical contact to the motherboard ground to provide a continuous ground for the system 5 2 Chapter 5 Advanced Motherboard Setup 5 3 Connecting Cables Now that the motherboard is installed the next step is to connect the cables to the board These include the data ribbon cables for the peripherals and control panel and the power cables Connecting Data Cables The ribbon cables used to transfer data from the peripheral devices have been carefully routed to prevent them from blocking the flow of cooling air that moves through the system from front to back If you need to disconnect any of these cables you should take care to keep them routed as they were originally after reconnecting them make sure the red wires connect to the pin 1 locations The following data cables with their locations noted should be con nected See the layout on page 5 10 for connector locations IDE Device Cables J18 and J19 Floppy Drive Cable J26 SCSI Device Cables JPA1 JPA2 JPA3 5011H only Control Panel Cable JF1 see next page Connecting Power Cables The P3TSSR P3TSSE has a 20 pin primary power supply connector designated ATX Power for connection to the ATX power supply See Section 5 8 for power connector pin definitions SUPERSERVER
83. nd with the rail guides facing inward Installing the Server into the Rack You should now have rails attached to both the chassis and the rack unit The next step is to install the server into the chassis Do this by lining up the rear of the chassis rails with the front of the rack rails Slide the chassis rails into the rack rails keeping the pressure even on both sides you may have to depress the locking tabs when inserting See Figure 2 3 When the server has been pushed completely into the rack you should hear the locking tabs click Finish by inserting and tightening the thumbscrews that hold the front of the server to the rack Figure 2 3 Installing the Server into a Rack 2 5 SUPERSERVER 5011H 5011E Manual Installing the Server into a Telco Rack If you are installing the SuperServer 5011H 5011E into a Telco type rack follow the directions given on the previous pages for rack installation The only difference in the installation procedure will be the positioning of the rack brackets to the rack They should be spaced apart just enough to accomodate the width of the telco rack Figure 2 4 Installing the Server into a Telco Rack 2 6 Chapter 2 Server Installation 2 5 Checking the Motherboard Setup After you install the 5011H 5011E in the rack you will need to open the unit to make sure the motherboard is properly installed and all the connections have been made 1
84. o detect S M A R T 32Bit Data Transfer The settings are Auto Disabled and Enabled Select En abled or Disabled to enable or disable the 32 bit Data Transfer function Select Auto to auto detect the 32 bit Data Transfer function ARMD Emulation This option is used to select the emulation used when config uring an LS120 MO Magneto Optical or lomega Zip drive The settings are Auto Floppy and HardDisk Primary IDE Slave When the system enters Setup BIOS automatically detects the presence of IDE devices This option displays the auto detection status of IDE de vices The settings for Primary IDE Slave are the same as those for the Primary IDE Master Secondary IDE Master This displays the status of auto detection of IDE devices The settings for Secondary IDE Master are the same as those for the Primary IDE Master Secondary IDE Slave This displays the status of auto detection of IDE devices The settings for Secondary IDE Slave are the same as those for the Primary IDE Master 7 10 Chapter 7 AMIBIOS Hard Disk Write Protect This item allows the user to prevent the hard disk from being overwritten The options are Enabled or Disabled Enabled allows the drive to be used normally read write and erase functions can all be performed Disabled prevents the hard disk from being erased This function is effective only when the device can be accessed through BIOS ATA PI Detect Timeout Set this op
85. ormation next The memory size information and the CPU registers are saved Entering real mode next Shutdown was successful The CPU is in real mode Disabling the Gate A20 line parity and the NMI next The A20 address line parity and the NMI are disabled Adjusting the memory size depending on relocation and shadowing next The memory size was adjusted for relocation and shadowing Clearing the Hit lt DEL gt message next The Hit lt DEL gt message is cleared The lt WAIT gt message is displayed Starting the DMA and interrupt controller test next B 5 SUPERSERVER 5011H 5011E Manual Checkpoint 60h 62h 65h 66h 67h 7Fh 80h 8th 82h 83h 84h 85h 86h 87h 88h 89h 8Bh 8Ch 8Dh 8Fh 9th Code Description The DMA page register test passed Performing the DMA Controller 1 base register test next The DMA controller 1 base register test passed Performing the DMA controller 2 base register test next The DMA controller 2 base register test passed Programming DMA controllers 1 and 2 next Completed programming DMA controllers 1 and 2 Initializing the 8259 interrupt controller next Completed 8259 interrupt controller initialization Extended NMI source enabling is in progress The keyboard test has started Clearing the output buffer and checking for stuck keys Issuing the keyboard reset command next A keyboard reset error or stuck key was found Issuing the keyboard controller int
86. ostic codes checkpoint codes to I O port 0080h If the computer cannot complete the boot process diagnostic equipment can be attached to the computer to read I O port 0080h B 1 Uncompressed Initialization Codes The uncompressed initialization checkpoint codes are listed in order of execution Checkpoint DOh Dih D3h D4h D5h D6h Code Description The NMI is disabled Power on delay is starting Next the initialization code checksum will be verified Initializing the DMA controller performing the keyboard controller BAT test starting memory refresh and entering 4 GB flat mode next Starting memory sizing next Returning to real mode Executing any OEM patches and setting the Stack next Passing control to the uncompressed code in shadow RAM at E000 0000h The initialization code is copied to segment 0 and control will be transferred to segment 0 Control is in segment 0 Next checking if lt Ctrl gt lt Home gt was pressed and verifying the system BIOS checksum If either lt Ctrl gt lt Home gt was pressed or the system BIOS checksum is bad next will go to checkpoint code EOh Otherwise going to checkpoint code D7h SUPERSERVER 5011H 5011E Manual B 2 Bootblock Recovery Codes The bootblock recovery checkpoint codes are listed in order of execution Checkpoint E0h Eth E2h Eh Edh Eeh Efh FOh Fih F2h F3h F4h FSh FBh FCh FDh FFh Code Description The onboard floppy controller
87. p Optimal default settings are in bold text unless otherwise noted The BIOS setup options described in this section are selected by choos ing the appropriate text from the Standard Setup screen All displayed text is described in this section although the screen display is often all you need to understand how to set the options see on next page 7 2 Chapter 7 AMIBIOS The Main BIOS Setup Menu Press the lt Delete gt key during the POST Power On Self Test to enter the Main Menu of the BIOS Setup Utility All Main Setup options are described in this section The Main BIOS Setup screeen is displayed below BIOS SETUP UTILITY Main Advanced Chipset PCIPnP Power Boot Security Exit AMIBIOS Version 07 00xx BIOS Build Date XX XX XX BIOS ID G SSR71020 Processor Type S PentiumIII Processor Speed 933MHz System Memory i 255MB System Time 10 10 00 System Date Thu 08 24 00 Select Screen Select Item Change Field Select Field General Help Save and Exit Exit Vv02 03 C Copyright 1985 2000 American Megatrends Inc Use the Up Down arrow keys or the lt Tab gt key to move between the different settings in the above menu When the items System Time and System Date are highlighted type in the correct time date in the time field and then press Enter The date must be entered in MM DD YY format The time is entered in HH MM SS format The time is in also 24 hour format For example 5 30 a m a
88. pe DMA 4 Type DMA 5 Type DMA 6 Type DMA 7 Type This above options allow you to change the protocol for DMA 0 through DMA 7 The settings for all are PC PCI and LPC DMA Processor Serial Number Intel includes a serial number in their processors to act as a unique system identifier For privacy reasons you can disable the release of this identifier The settings for this option are Disabled and Enabled Disabled This set ting restricts all access to the CPU serial number from your CPU Enabled This setting allows the operating system and applications to be able to read the CPU serial number from your CPUs Note If the CPU is a Intel Celeron Processor then this selection will be grayed out Intel Celeron Processors do not contain a processor serial number CPU Latency Timer This option allows the CPU Latency Timer to be modified The settings for this option are Disabled and Enabled Disabled The deferrable processor cycle will be deferred immediately after receiving another ADS Enabled The deferrable processor cycle will only be deferred after it has been in a Snoop Stall for 31 clocks and another ADS has arrived 7 21 SUPERSERVER 5011H 5011E User s Manual C000 16k Shadow C400 16k Shadow C800 16k Shadow Ccoo 16k Shadow D000 16k Shadow D400 16k Shadow D800 16k Shadow DC00 16k Shadow These options specify how the 16 KB of video ROM at each of the above addresses is treated The settings are Disabl
89. plug the power cords of all the power supply units in the system When working around exposed electrical circuits another person who is familiar with the power off controls should be nearby to switch off the power if necessary Use only one hand when working with powered on electrical equipment This is to avoid making a complete circuit which will cause electrical shock Use extreme caution when using metal tools which can easily damage any electrical components or circuit boards they come into contact with Do not use mats designed to decrease static electrical discharge as protection from electrical shock Instead use rubber mats that have been specifically designed as electrical insulators The power supply power cords must include a grounding plug and must be plugged into grounded electrical outlets 4 1 SUPERSERVER 5011H 5011E Manual Motherboard Battery CAUTION There is a danger of explosion if the onboard battery located near the AGP slot is installed upside down which will reverse its polarites This battery must be replaced only with the same or an equivalent type recommended by the manufacturer Dispose of used batteries according to the manufacturer s instructions 4 2 General Safety Precautions A Follow these rules to ensure general safety Keep the area around the SuperServer 5011H 5011E clean and free of clutter The SuperServer 5011H 5011E weighs approx 26 Ibs 11 8 kg when
90. ppears as 05 30 00 and 5 30 p m as 17 30 00 Press the lt ESC gt key to exit the Main Menu and use the Left Right arrow keys to enter the the other categories of BIOS settings The next section is described in detail to illustrate how to navigate through the menus Note Items displayed in gray are preset and cannot be selected 7 3 SUPERSERVER 5011H 5011E User s Manual 7 4 Advanced Chipset Setup Choose Advanced BIOS Setup from the AMIBIOS Setup Utility main menu with the Left Right arrow keys You should see the following display Select one of the items in the left frame of the screen such as SuperlO Configuration to go to the sub screen for that item Advanced BIOS Setup options are displayed by highlighting the option using the arrow keys All Advanced BIOS Setup options are described in this section BIOS SETUP UTILITY Main Advanced Chipset PCIPnP Power Boot Security Exit Setup Warning Configure SuperIO Setting items on this screen to incorrect Chipset Winbond627F values may cause the system to malfunction gt Health Monitor Features gt SuperIO Configuration gt IDE Configuration gt Floppy Configuration gt Boot Settings Configuration gt gt gt Peripheral Device Configuration Event Log Configuration Processor Configuration Select Screen TL Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit Vv02 03 C Copyright 1985 2000 American Megatrends
91. r heatsink installation 3 Removing the processors To remove the processor from the motherboard simply follow the installation process in reverse order Figure 5 3 FCPGA Socket Empty and with Processor Installed Figure 5 4 Heatsink Installation Procedure m Ee LA Chapter 5 Advanced Motherboard Setup 5 6 Installing Memory CAUTION Exercise extreme care when install IN ing or removing DIMM modules to prevent any possible damage 1 Memory support The P38TSSR P3TSSE has three 25 degree DIMMs that support 64MB 128MB 256MB 512 MB unbuffered SDRAM PC133 and PC100 memory are both supported at their respective speeds However if three DIMM modules are installed the memory will run at 100MHz even if PC133 memory is used due to chipset limitations 2 Installing memory modules Insert each DIMM module into its slot at a 25 degree angle Pay attention to the two notches along the bottom of the module to prevent inserting the DIMM module incorrectly Gently press down on the DIMM module until it snaps into place in the slot see Figure 5 5 Figure 5 5 Side View of DIMM Installation into Slot Notches D Se pees STE pet ted r Matcher Release Note Notches Release Tak should align Tab with the receptive points on the slot To Install Insert module vertically and press down until it snaps into place Pay attention to the bottom notches To
92. rack to enable you to open the front door completely 25 inches Leave approximately 30 inches of clearance in the back of the rack to allow for sufficient airflow and ease in servicing A N Warnings and Precautions AN Rack Precautions Ensure that the leveling jacks on the bottom of the rack are fully extended to the floor with the full weight of the rack resting on them In a single rack installation stabilizers should be attached to the rack In multiple rack installations the racks should be coupled together Always make sure the rack is stable before extending a component from the rack You should extend only one component at a time extending two or more simultaneously may cause the rack to become unstable Server Precautions Review the electrical and general safety precautions in Chapter 4 Determine the placement of each component in the rack before you install the rails Install the heaviest server components on the bottom of the rack first and then work up Use a regulating uninterruptible power supply UPS to protect the server from power surges voltage spikes and to keep your system operating in case of a power failure Allow the power supply units and hot plug SCSI drives 5011H to cool before touching them Always keep the rack s front door and all panels and components on the servers closed when not servicing to maintain proper cooling 2 2 Chapter 2 Server Installation 2 4 In
93. rol to the video ROM to perform any required configu ration before the video ROM test All necessary processing before passing control to the video ROM is done Looking for the video ROM next and passing control to it B 3 SUPERSERVER 5011H 5011E Manual Checkpoint 2Dh 23h 24h 25h 27h 28h 2Ah 2Eh 2Fh 30h 3th 32h 34h 37h 38h 39h 3Ah 3Bh 40h 42h 43h Code Description The video ROM has returned control to BIOS POST Performing any required processing after the video ROM had control Reading the 8042 input port and disabling the MEGAKEY Green PC feature next Making the BIOS code segment writeable and performing any necessary configuration before initializing the interrupt vectors The configuration required before interrupt vector initialization has completed Interrupt vector initialization is about to begin Interrupt vector initialization is done Clearing the password if the POST DIAG switch is on Any initialization before setting video mode will be done next Initialization before setting the video mode is complete Configuring the monochrome mode and color mode settings next Bus initialization system static output devices will be done next if present See the last page for additional information Completed post video ROM test processing If the EGA VGA controller is not found performing the display memory read write test next The EGA VGA controller was not found The display memor
94. rt Philips screwdriver 5 1 Handling the P3TSSR P3TSSE Motherboard Electric static discharge ESD can damage electronic components To pre vent damage to any printed circuit boards PCBs it is important to handle them very carefully see previous chapter Also note that the size and weight of the P3TSSR P3TSSE motherboard may cause it to bend if handled improperly which may result in damage To prevent the P3TSSR P3TSS motherboard from bending keep one hand under the center of the board to support it when handling The following measures are generally sufficient to protect your equipment from electric static discharge Precautions e Use a grounded wrist strap designed to prevent Electric Static Discharge ESD e Touch a grounded metal object before removing any board from its anti static bag e Handle a board by its edges only do not touch its components periph eral chips memory modules or gold contacts e When handling chips or modules avoid touching their pins e Put the motherboard add on cards and peripherals back into their anti 5 1 SUPERSERVER 5011H 5011E Manual static bags when not in use e For grounding purposes make sure your computer chassis provides ex cellent conductivity between the power supply the case the mounting fasteners and the motherboard Unpacking The motherboard is shipped in antistatic packaging to avoid electrical static discharge When unpacking the board make sure the per
95. s Floppy Connechor eeeeeeceeceeceeeeeeeeeeeeeceeceeeeeeeaesaeeaeeeseeeeateaeeaetaeeenes IDE Connectors a a a A Ee aE EA EAE aS S A Ultra160 SCSI Connectors iinn an ee aa Chapter 6 Advanced Chassis Setup 6 1 Static Sensitive Devices AE 6 1 6 2 Control Panel cissreic 4 sien acieetii EENS 6 2 6 3 System Fafe candi aie asi tee ira ies dE 6 3 System Fan Failure oo cee eecseeeeeeeeeeeeseeseeeeeeeceeeeceeeeeeeaeeaeseeeeseeeeeseaeeas 6 3 Replacing System Cooling Fans 6 3 6 4 Drive Bay Installation REMOVAlI eee cece eee eee eee eeeeeseeeteeteeeneeeeenaes 6 4 Accessing the Drive Days 6 4 SCSI Drive Installation ee eeeeeseeseeeeeeeceeceeeeeeeeeeeeeaesaeeaeenesneeeeeeeeeaees 6 5 IDE Drive Installation ccseccsssscsscccesssseesscccesesserssceseseseeeseeesensteansecess 6 7 CD ROM and Floppy Drive Installation esseere 6 8 6 5 Power S ppl tee ed ean denied tinea 6 9 Power Supply Failure 00 cececceeecceceeseeeeeeeceeeeeeeeceeeeaeeseeaeeeeeeeseeeeaeeaeeaes 6 9 Replacing the Power Supply cceccecsseseesereeeceeeeeeeeeeeeeeeeeseeeeaeeaeeaes 6 9 Chapter 7 BIOS Eau tee ee KEE 7 2 BIOS E e 7 3 Running Setup genug ees dE ale hated ed The Main BIOS Setup Menu 7 4 Advanced Chipset Setup e cece eeceeeeeeceeseeeeeeseeeeeceeseeeesesaeeaeeateeeeeeseateas Health Monitor Features cccssscssscssssecesssccsseseeesseesssnseaesseeseseseanseeens Super UO Configuration oo ceeceecceceeseeseeeeee
96. seals are located under the blower fan and beneath the frame cross section that separates the drive bay area from the motherboard area of the chassis NIC2 e NIC2 Indicates network activity on LAN2 when flashing NIC1 o NIC1 Indicates network activity on LAN1 when flashing d HDD Indicates IDE channel activity On the SuperServer 5011H 5011E this light indicates CD ROM drive activity when flashing Chapter 3 System Interface o Power Indicates power is being supplied to the system s power supply units This LED should normally be illuminated when the system is operating 3 4 SCSI Drive Carrier LEDs 5011H only Each SCSI drive carrier has two LEDs Green When illuminated the green LED on the front of the SCSI drive carrier indicates drive activity A connection to the SCSI SCA backplane enables this LED to blink on and off when that particular drive is being accessed e Red A SAF TE compliant backplane is needed to activate the red LED to indicate a drive failure A SAF TE compliant SCSI backplane is optional on the 5011H If one of the SCSI drives fail you should be notified by your system management software Please refer to Section 6 4 for instructions on replacing failed SCSI drives 3 5 Power Supply Switch An on off switch is located on the back of the power supply This switch should normally be on at all times Turning this switch to the off position removes both the main and standby power fro
97. sector of your hard disk drive The settings for this option Disabled and Enabled If Enabled AMIBIOS will display a warning when any program or virus issues a Disk Format command or attempts to write to the boot sector of the hard disk drive 7 36 Chapter 7 AMIBIOS 7 10 Exit Setup Choose Exit Setup from the AMIBIOS Setup main menu All Exit Setup op tions are described in this section The Exit Setup screen is shown below BIOS SETUP UTILITY Main Advanced Chipset PCIPnP Power Boot Security Exit Exit system setup with Exit Saving Changes saving the changes Exit Discarding Changes Load Optimal Defaults Load Fail Safe Defaults Discard Changes Select Screen Select Item Go to Sub Scree General Help Save and Exit Exit V02 03 C Copyright 1985 2000 American Megatrends Inc Exit Saving Changes Highlighting this setting and then pressing lt Enter gt will save any changes you made in the BIOS Setup program and then exit Your system should then continue with the boot up procedure Exit Discarding Changes Highlighting this setting and then pressing lt Enter gt will ignore any changes you made in the BIOS Setup program and then exit Your system should then continue with the boot up procedure 7 37 SUPERSERVER 5011H 5011E User s Manual Load Optimal Defaults Highlighting this setting and then pressing lt Enter gt provides the optimum performance settings for all devices and system features
98. son handling it is static protected 5 2 Motherboard Installation This section explains the first step of physically mounting the P83TSSR 5011H or P3TSSE 5010E into the SC810 chassis Following the steps in the order given will eliminate the most common problems encountered in such an installation To remove the motherboard follow the procedure in reverse order 1 Accessing the inside of the 5011H 5011E see Figure 2 5 Two release buttons are located on the top cover of the chassis Depressing both of these buttons while pushing the cover away from you until it stops You can then lift the top cover from the chassis to gain full access to the inside of the server If already installed in a rack you must first release the retention screws that secure the unit to the rack Then grasp the two handles on either side and pull the unit straight out until the rails lock into place 2 Check compatibility of motherboard ports and I O shield The P3TSSR P3TSSE requires a chassis big enough to support a 12 x 8 7 motherboard such as Supermicro s SC810 1U rackmount Make sure that the I O ports on the motherboard align properly with their respective holes in the I O shield at the back of the chassis 3 Mounting the motherboard onto the motherboard tray Carefully mount the motherboard to the motherboard tray by aligning the board holes with the raised metal standoffs that are visible on the bottom of the chassis Insert screws into all the
99. ssis making them easily accessible for installation and removal The IDE drives are not hot swap units meaning system power must be turned off before installing and or removing them To install or remove a drive first power down the system and then remove the top cover of the chassis Un screw the retention screw at the top center of the drive then push the drive carrier out from the back until you can grasp and pull it out through the front of the chassis see Figure 6 6 Reverse this procedure when installing a drive carrier making sure you screw in the retention screw Replace the top cover when finished SUPERSERVER 5011H 5011E Manual Figure 6 6 Removing IDE Drives 5011E CD ROM and Floppy Drive Installation The top cover of the chassis must be opened to gain full access to the CD ROM and floppy drive bays The CD ROM drive must have a slim profile to fit into the 5011H 5011E First release the retention screws that secure the unit to the rack Grasp the two handles on either side and pull the unit straight out until it locks you will hear a click Next depress the two buttons on the top of the chassis to release the top cover and at the same time push the cover away from you until it stops You can then lift the top cover from the chassis to gain full access to the inside of the server You must power down the system before installing or removing floppy or IDE drives Drives mount on rails and should
100. stalling the SuperServer 5011H 5011E into a Rack This section provides information on installing the SuperServer 5011H 5011E into a rack unit If the 5011H 5011E has already been mounted into a rack you can skip ahead to Sections 2 5 and 2 6 There are a variety of rack units on the market which may mean the assembly procedure will differ slightly The following is a guideline for installing the 5011H 5011E into a rack with the rack rails provided with the system You should also refer to the installation instructions that came with the rack unit you are using Identifying the Sections of the Rack Rails You should have received two rack rail assemblies with the SuperServer 5011H 5011E Each of these assemblies consist of two sections an inner fixed chassis rail that secures to the 5011H 5011E A and an outer fixed rack rail that secures directly to the rack itself B A sliding rail guide sandwiched between the two should remain attached to the fixed rack rail see Figure 2 1 The A and B rails must be detached from each other to install To remove the fixed chassis rail A pull it out as far as possible you should hear a click sound as a locking tab emerges from inside the rail assembly and locks the inner rail Then depress the locking tab to pull the inner rail completely out Do this for both the left and right side rack rail assemblies Locking Tab 6 Figure 2 1 Identifying the Sections of the Rack Rails 2 3 SU
101. supports single Intel Pentium Ill FCPGA 500 MHz 1 26 GHz processors and Celeron FCPGA PPGA 600 850 pro cessors and up to 512 MB SDRAM main memory Manual Organization Chapter 1 Introduction The first chapter provides a checklist of the main components included with the server system and describes the main features of the Super P3TSSR and P3TSSE mainboards and the SC810 chassis Chapter 2 Server Installation This chapter describes the steps necessary to install the SuperServer 5011H 5011E into a rack and check out the server configuration prior to powering up the system If your server was ordered without the proces sor and memory components this chapter will refer you to the appropriate sections of the manual for their installation Chapter 3 System Interface Refer to this chapter for details on the system interface which includes the functions and information provided by the control panel on the chassis as well as other LEDs located throughout the system SUPERSERVER 5011H 5011E Manual Chapter 4 System Safety You should thoroughly familiarize yourself with this chapter for a general overview of safety precautions that should be followed when installing and servicing the SuperServer 5011H 5011E Chapter 5 Advanced Motherboard Setup Chapter 5 provides detailed information on the P3TSSR and P3TSSE motherboards including the locations and functions of connectors head ers jumpers DIP switches and IRQs
102. tes next Memory wait state programming is over Clearing the screen and enabling parity and the NMI next NMI and parity enabled Performing any initialization required before passing control to the adaptor ROM at E000 next Initialization before passing control to the adaptor ROM at E000h completed Passing control to the adaptor ROM at E000h next Returned from adaptor ROM at E000h control Performing any initialization required after the E000 option ROM had control next Initialization after E000 option ROM control has completed Displaying the system configuration next Uncompressing the DMI data and executing DMI POST initialization next The system configuration is displayed Copying any code to specific areas Code copying to specific areas is done Passing control to INT 19h boot loader next B 7 SUPERSERVER 5011H 5011E Manual BA Bus Checkpoint Codes The system BIOS passes control to different buses at the following checkpoints Checkpoint 2Ah 38h 39h 95h Code Description Initializing the different bus system static and output devices if present Initialized bus input IPL and general devices if present Displaying bus initialization error messages if any Initializing bus adaptor ROMs from C8000h through D8000h Additional Bus Checkpoints While control is inside the different bus routines additional checkpoints are output to UO port address 0080h as word to identify the routines being executed
103. the BIOS from using Multi Sector Transfer on the specified channel The data to and from the device will occur one sector at a time Auto This option allows the BIOS to auto detect device support for Multi Sector Trans fers on the specified channel If supported this option al lows the BIOS to auto detect the number of sectors per block for transfer from the hard disk drive to memory The data transfer to and from the device will occur multiple sectors at a time if the device supports it PIO Mode IDE PIO Programmable I O mode programs timing cycles be tween the IDE drive and the programmable IDE controller As the PIO mode increases the cycle time decreases The settings are Auto 0 1 2 3 and 4 DMA This item allows the users to select the DMA mode The settings are Auto SWDMAO SWDMA1 SWDMA2 MWDMAO MWDMA1 MWDM2 UWDMAO UWDMA1 UWDMA2 UWDMA3 and UWDMA4 Select Auto to auto de 7 9 SUPERSERVER 5011H 5011E User s Manual tect the DMA Mode Select SWDMAO through SWDMA2 to set single word DMAO through DMA2 Select MWDMAO through MWDMAZ2 to set Multi word DMAO through DMA2 Select UDMAO trhough UDMA4 to set Ultra DMAO through Ultra DMA4 S M A R T S M A R T stands for Self Monitoring Analysis and Reporting Technology a feature that can help predict impending drive failures The settings are Auto Disabled and Enabled Select Enabled or Disabled to enable or disable the S M A R T Select Auto to aut
104. the graphics aperture size to either 64 MB or 32 MB 7 17 SUPERSERVER 5011H 5011E User s Manual Init Display Cache Memory This option allows the Initial Display cache memory to be adjusted The setting are Enabled and Disabled Paging Mode Control This option allows the paging mode controls to be adjusted to either Close or Open RAS to CAS Latency Override The RAS to CAS Override is adjusted with this option The settings are Disabled and Enabled Disabled This option allows RAS to CAS Enabled This option overrides RAS to CAS SDRAM stores informa tion in blocks of rows and columns RAS stands for Row Address Strobe CAS stands for Column Address Strobe CAS Latency This option regulates the speed of the Column Address Strobe CAS as either Fast or Slow which is higher or lower latency CAS latency optimizes the speed at which data is accessed in a column by defining CAS latency time in 100 MHz or 133 MHz clocks dependent on the memory bus speed It controls the time delay in clocks before SDRAM starts a read command after receiving it Reading RAS data can be read twice as fast as reading CAS Lowering the latency can increase the speed of the SDRAM but at the expense of stability RAS Timing This option regulates the speed of the Row Address Strobe RAS as either Fast or Slow As with CAS Latency lowering the timing can increase the speed of the SDRAM but at the expense of stability RAS Pre charge
105. tic discharge Keep all components and printed circuit boards PCBs in their antistatic bags until ready for use Touch a grounded metal object before removing the board from the antistatic bag Do not let components or PCBs come into contact with your clothing which may retain a charge even if you are wearing a wrist strap Handle a board by its edges only do not touch its components peripheral chips memory modules or contacts When handling chips or modules avoid touching their pins Put the motherboard and peripherals back into their antistatic bags when not in use For grounding purposes make sure your computer chassis provides excellent conductivity between the power supply the case the mounting fasteners and the motherboard 4 3 SUPERSERVER 5011H 5011E Manual NOTES 4 4 Chapter 5 Advanced Motherboard Setup Chapter 5 Advanced Motherboard Setup This chapter covers the steps required to install the P83TSSR P3TSSE moth erboard into the SC810 chassis connect the data and power cables and install add on cards All motherboard jumpers and connections are also described A layout and quick reference chart are on pages 5 10 through 5 13 Remember to completely close the chassis when you have finished working with the motherboard to better cool and protect the system Tools Required The only tools you will need to install the P3TSSR P3TSSE into the chassis are a long and a sho
106. tion to stop the system search for ATAPI devices within the specified number of seconds The options are 0 5 10 15 20 25 30 and 35 seconds Most ATA disk drives can be detected within 5 seconds ATA PI 80Pin Cable Detection This option selects the mechanism for detecting the 80 pin ATA PI cable Options include Host and Device Host and Device Host This option uses the motherboard onboard IDE controller to detect the type of IDE cable used Device This option uses the IDE disk drive to detect the type of IDE cable used Host amp Device This option uses both the motherboard onboard IDE controller and IDE disk drive to detect the type of IDE cable used Floppy Configuration Floppy A Use this option to specify which of floppy drive you have installed in the A drive The settings are Disabled 360 KB 5 1 4 1 2 MB 5 1 4 720 KB 3 1 2 1 44 MB 3 1 2 and 2 88 MB 3 1 2 Floppy B Use this option to specify which of floppy drive you have installed in the B drive The settings are Disabled 360 KB 5 1 4 1 2 MB 5 1 4 720 KB 3 1 2 1 44 MB 3 1 2 and 2 88 MB 3 1 2 Floppy Drive Seek Use this option to Enable or Disable the floppy seek routine on bootup 7 11 SUPERSERVER 5011H 5011E User s Manual Boot Settings Configuration Quick Boot This option allows the BIOS to skip certain tests that are normally performed on boot up You can disable the option to speed up boot time The settings are Disabled and Enab
107. umper JP36 allows you to enable Jumper Settings JP36 or disable the Watchdog feature Jumper das A Position Definition The normal default position is Open Watchdog closed to disable the watchdog Closed Speaker timer and enable the speaker See the table on the right for jumper settings 5 22 Chapter 5 Advanced Motherboard Setup 5 10 Floppy Hard Disk and SCSI Connections Be aware of the following when connecting the floppy and hard disk drive cables e A red mark on a wire typically designates the location of pin 1 e A single floppy disk drive ribbon cable has 34 wires and two connectors to provide for two floppy disk drives The connector with the twisted wires always connects to drive A and the connector that does not have twisted wires always connects to drive B Floppy Connector Floppy Connector Pin Definitions J26 The floppy connector is located Pin Number Function Pin Number Function 1 GND 2 FDHDIN on J26 and requires a 34 pin rib 3 GND 4 Reserved bon cable for operation See the gt eh i E table on the right for pin defini 9 GND 10 Motor Enable d 1 GND 12 Drive Select B tions 13 GND 14 Drive Select A 15 GND 16 Motor Enable 17 GND 18 DIR 19 GND 20 STEP 2 GND 22 Write Data 23 GND 24 Write Gate 25 GND 26 Track 00 27 GND 28 Write Protect 29 GND 30 Read Data 3 GND 32 Side 1 Select 33 GND 34 Diskette IDE Connector Pin Definitions 918 319 ID
108. ure 6 5 Removing SCSI Drives 5011H are installed both SCSI drive carriers must remain in the drive bays to maintain proper airflow d Important Regardless of how many SCSI hard drives Chapter 6 Advanced Chassis Setup SCSI Power Cables SCSI power cables should be routed so that they do not block the airflow through the chassis There is a 4 pin connector for the power cables SCA Backplane The SCSI drives plug into an SCA backplane that provides power SCSI ID and bus termination A RAID controller can be used with the SCA backplane to provide data security The operating system you use must have RAID support to enable the hot swap capability of the SCSI drives The SCA SCSI backplane is already preconfigured so there are no jumpers or switches present on it IDE Drive Installation 5011E only 1 Mounting an IDE drive in a drive carrier Like SCSI drives IDE drives are also mounted in drive carriers to simplify their installation and removal from the chassis These carriers also help promote proper airflow For this reason even empty carriers without IDE drives installed must remain in the chassis To add a new IDE drive install a drive into the carrier with the printed circuit board side toward the carrier so that the mounting holes align with those in the carrier Secure the drive to the carrier with the four screws 2 Installing removing IDE drives The two IDE drive bays are located in the front of the cha
109. y read write test is about to begin The display memory read write test passed Look for retrace checking next The display memory read write test or retrace checking failed Performing the alternate display memory read write test next The alternate display memory read write test passed Looking for alternate display retrace checking next Video display checking is over Setting the display mode next The display mode is set Displaying the power on message next Initializing the bus input IPL general devices next if present See the last page of this chapter for additional information Displaying bus initialization error messages See the last page of this chapter for additional information The new cursor position has been read and saved Displaying the Hit lt DEL gt message next The Hit lt DEL gt message is displayed The protected mode memory test is about to start Preparing the descriptor tables next The descriptor tables are prepared Entering protected mode for the memory test next Entered protected mode Enabling interrupts for diagnostics mode next B 4 Appendix B AMIBIOS POST Checkpoint Codes Checkpoint 44h 45h 46h 47h 48h 49h 4Bh 4Ch 4Dh 4Eh 4Fh 50h 51h 52h 53h 54h 57h 58h 59h Code Description Interrupts enabled if the diagnostics switch is on Initializing data to check memory wraparound at 0 0 next Data initialized Checking for memory wrap

SuperMicro 5011h Motherboard

Contents

Download Pdf Manuals

Related Search

Related Contents