U-Line CO2075FF Compact Refrigerator
Contents
1. graining in the stainless to become blurred e Rust that is allowed to linger can penetrate into the surface of the stainless steel and complete removal of the rust may not be possible 3 Prepare Site Your U Line product has been designed for either free standing or built in installation When built in your unit does not require additional air space for top sides or rear However the front grille must NOT be obstructed and clearance is required for water drain and electrical connections in the rear Note Unit can NOT be installed behind a closed cabinet door Cut Out Dimensions See Electrical Specifications for Power Supply 23 11 16 Figure 1 Follow the cut out drawing in Figure 1 The 24 3 16 width allows 1 4 for ease in installation and removal of the unit 24 is the counter depth in most installations The unit is 23 11 16 deep including the handle on Black and White models and 23 11 16 deep including the door and not the handle on Stainless Steel models see Figure 2 www U LineService com 02 2005 CO2075FF Ice Maker Refrigerator Product Dimensions 23 11 16 Including Handle 23 15 16 gt Black and White Figure 2 25 13 16 Including Handle ee 23 15 16 Stainless Steel y U LINE CORPORATION Reversing the Door Black and White Units Only All U Line units except Stain2. Service com CO2075FF Ice Maker Refrigerator 1 Follow Safety Precautions IMPORTANT PLEASE READ all instructions completely before attempting to install or operate the unit e This unit requires connection to the water supply Improper hook up can result in substantial property damage If you are unsure of your ability to safely connect the water supply to the unit consult a licensed plumber for assistance This unit requires connection to a grounded three prong polarized receptacle that has been placed by a qualified electrician in accordance with applicable electrical codes Safety Alert Definitions Safety items throughout this guide are labeled with a Danger Warning or Caution based on the risk type A DANGER Danger means that failure to follow this safety statement will result in severe personal injury or death A WARNING Warning means that failure to follow this safety statement could result in serious personal injury or death A CAUTION Caution means that failure to follow this safety statement may result in minor or moderate personal injury property or equipment damage 02 2005 CO2075FF Ice Maker Refrigerator General Precautions Use this appliance for its intended purpose only and follow these general precautions along with those listed throughout this guide N WARNING SHOCK HAZARD Electrical Grounding Required Keep the unit unplugged throughout installa
3. U UFLINE C ORPORATION Echelon Series Installation Guide EE CO2075FF Ice Maker Refrigerator www U LineService com Phone 414 354 0300 e FAX 414 354 7905 Service amp Parts Tech Lines Phone 800 779 2547 FAX 414 354 5696 OnlineService U Line com 2005 U Line Corporation 02 2005 U U LINE CORPORATION Contents Exterior Cleaning 4 Cut Out Dimensions 4 Product Dimensions 5 Door Swing Clearances Information 5 Reversing the Door 5 Other Site Requirements 6 Side By Side Installation Instructions 7 Custom 1 4 Door Panel Insert 7 Full Overlay Door Panel 8 Checking Door Alignment 12 Adjusting Door Alignment 12 Water Supply Connection 13 Electrical Specifications 14 Leveling Information 14 Installation Tip 14 Installation of the CO2075FF 15 Relocating the Shelves 15 Installation Troubleshooting 15 Initial Start Up 16 Start Up Troubleshooting 16 Service Information 17 www U Line
4. ite side BOTTOM see Figure 7 www U LineService com U U LINE CORPORATION 4 Remove the two door closer inserts from the existing bottom hinge and install as shown on the new bottom hinge see Figure 8 Door Closer Inserts Figure 7 Figure 8 5 Remove existing bottom hinge 3 screws and remount on opposite side TOP Remove hinge screw pin 6 Remove the plastic hole plug from the top of the door to allow the pivot pin to be inserted in the new location Install the plug into the vacated hole on the opposite side 7 With bottom of door facing up remove pivot plate 2 screws flip over and remount on opposite side of door see Figure 9 Be sure notch in plate faces center 8 Holding door upright with top of door tilted forward place hole of door pivot plate on bottom hinge screw pin see Figure 10 9 Tilt top of door into position in top hinge and install top hinge screw pin 10 Install plastic screw plugs removed in Step 2 in old hinge holes 3 each top and bottom Figure 10 www U LineService com CO2075FF Ice Maker Refrigerator Other Site Requirements Power Supply The unit requires a grounded and polarized 115 VAC 60 Hz 15A circuit normal household current See Electrical Specifications on Page 14 Water Supply The unit requires a 1 4 inch OD water supply line and a shut off valve For more information see Page 13 E
5. less Steel models may be left or right hand opening The door opening is easily reversed by moving the hinge hardware to the opposite side The top hinge hardware will be used on the bottom of the other side and the bottom hinge hardware will be used on the top of the other side see Figure 4 To reverse the door 1 Remove top hinge screw pin from door 7 64 Allen Figure 4 Please note that the unit has adjustable feet that can add one additional inch to height during leveling or to match adjacent cabinets see Figure 35 on Page 14 Door Swing Clearances Information Black and White units have a zero clearance for the door to open 90 see Figure 3 Stainless Steel models require a minimum of 2 1 8 door clearance to accommodate the handle if the unit is installed next to a wall or similar type of structure wrench or Phillips screwdriver depending on your unit s construction see Figure 5 Remove door by tilting forward and lifting off bottom hinge pin 2 Remove plastic screw plugs 3 each top and bottom from new hinge location Do not discard see Figure 6 Screw Plugs Wall 1 4 Min Wall MMA 2 1 8 Min gt rs Door Swing Black and White Figure 3 02 2005 Door Swing Stainless Steel Figure 5 Figure 6 3 Remove top hinge 3 screws reinstall hinge screw pin and remount on oppos
6. nvironmental Requirements The surrounding air temperature must be at least 50 F 10 C but must not exceed 110 F 40 C High ambient temperature ranges and warmer water supply will cause reduced ice production Black and White units may be installed outdoors in a covered area Stainless Steel CO2075FF units are deemed suitable for outdoor use by UL The unit must not be located near heat generating equipment or in direct sunlight 02 2005 CO2075FF Ice Maker Refrigerator Side By Side Installation Instructions For a complete refreshment center install your CO2075FF Ice Maker Refrigerator beside a U Line Drawer or Wine Captain Model see Figure 11 for typical cut out Note that each Side By Side Installation will be different e Cut out width for a side by side installation is the total of the widths listed under Cut Out Dimensions in each unit s Installation Guide For example Placing a CO2075FF Ice Maker Refrigerator next to a 2015 series unit would require a cut out width of 24 3 16 15 3 16 39 3 8 Placing a CO2075FF Ice Maker Refrigerator next to a 2075 series unit would require a cut out width of 24 3 16 24 3 16 48 3 8 e No trim kit is required However 1 4 inch space needs to be maintained between the units to ensure unobstructed door swing e Units must operate from separate properly grounded electrical receptacles placed according to each unit s Electrical Specifications Typical Side B
7. on see Figure 12 Remove door by tilting forward and lifting off bottom hinge pin www U LineService com U U LINE CORPORATION Figure 12 Figure 13 3 Pull door gasket out of groove top edge of door only Start in the middle and pull outward moving toward the edge see Figure 13 This may take some force Do not remove the three screws behind gasket 4 Remove two outside screws holding door handle Slightly separate door handle from door see Figure 14 5 Pull handle up and off 6 Remove and discard existing panel and cardboard spacer 7 Slide custom door panel insert into 1 4 inch channel in door front 8 Holding door gasket out of the way replace handle Figure 14 on door making sure it is seated properly on insert and that screw holes line up 9 Install two small screws removed in Step 4 10 Starting at the corners and working inward push door gasket into place on door 11 Place door on bottom hinge pin and install upper hinge screw 12 Reinstall the door shelves by lining up the bosses and first pushing straight in then down at a 45 angle see Figure 37 on Page 15 Go on to 5 Adjust Door www U LineService com CO2075FF Ice Maker Refrigerator Full Overlay Door Panel Door Panel Preparation A full overlay door panel completely covers the doorframe and handle to give a built in appearance See your U Line dealer for the optional Full Overlay Door Panel Ki
8. t P N U OL2075B Black or P N U OL2075W White Appropriate hardware Modified Handle Replacement Hinges and a copy of these instructions will be included in the kit 1 Cut the overlay to the following dimensions see Figure 15 Full Overlay Dimensions Width 23 3 4 Height 29 7 8 The door panel must not weigh more than 20 Ibs Relief Notch for Pivot Plate Rear View of Wood Panel Figure 15 IMPORTANT Rear View of wood panel for right hand hinge shown Use mirror image for left hand hinges 2 Create a relief Figure 15 for pivot plate by cutting notch in top corner and coinciding back corner of overlay panel Refer to Figure 16 for exact specifications 02 2005
9. t accept custom panels Please carefully follow the directions that apply to your unit and your intended design Tools Materials Required e 7 64 Allen wrench e Screwdrivers slotted and Phillips head e 1 4 inch OD copper tubing and shut off valve for water supply line e 1 4 inch thick door panel material and cutting tools Black or White units e Full Overlay Door Panel Kit part number U OL2075B Black or part number U OL2075W White 3 4 inch door panel overlay cutting tools drill and bits Black or White units Inspection Unwrap and inspect the unit on a flat level surface capable of supporting its entire weight Removing Protective Coating Stainless Steel Units Only When inspecting installing a Stainless Steel unit the protective coating covering the unit must be removed first Start at a corner of the unit door and pull back the protective coating to remove it from the unit door www U LineService com U U LINE CO2075FF Ice Maker Refrigerator CORPORATION After all the protective coating has been removed from the unit door clean all Stainless Steel surfaces with Claire Stainless Steel Polish and Cleaner or comparable product or a mild detergent and warm water solution and soft cloth Do NOT use abrasive cleaning agents Note If cleaning with mild detergent and warm water solution and soft cloth the unit MUST be treated with Claire Stainless Steel Polish and Cleaner or comparable product
10. tion except during testing es Never remove the round grounding prong from the plug and never use a two prong grounding adapter es Never use an extension cord to connect power to the unit es Always keep your working area dry CAUTION e Use care when moving and handling the unit Use gloves to prevent personal injury from sharp edges e Do not lift the unit by the door or door handle e Do not install the unit behind closed doors or in any way that would obstruct airflow to the front grille which may cause the unit to malfunction 02 2005 U U LINE CORPORATION 2 lInspect and Plan You have received a carton containing your CO2075FF Ice Maker Refrigerator with a package inside containing a User Manual a Product Registration Card and water connection parts Complete and mail the Product Registration Card or register online at www U LineService com Once your unit is installed keep the User Manual and this Installation Guide in a safe place for future reference Your unit is Black White or Stainless Steel Black and White units have a reversible door with a slightly contoured handle across the top They come with a flush mounted door panel that when removed will accept a custom 1 4 inch thick door panel or a 3 4 inch thick full overlay door panel Stainless Steel units are covered with a protective coating and have been ordered left or right hand hinged The Stainless doors are not reversible and do no
11. to prevent discoloration Exterior Cleaning As Required Black and White Models e The door grille and cabinet may be cleaned with a mild detergent and warm water solution Do not use solvent based or abrasive cleaners Use a soft sponge and rinse with clean water Wipe with a soft clean towel to prevent water spotting Stainless Steel Models e Stainless steel models can discolor when exposed to chlorine gas pool chemicals salt water or cleaners with bleach e Keep your stainless steel unit looking new by cleaning with a good quality all in one stainless steel cleaner polish on a monthly basis For best results use Claire Stainless Steel Polish and Cleaner which can be purchased from U Line Corporation The part number is 173348 Comparable products are acceptable Frequent cleaning will remove surface contamination that could lead to rust Some installations may require cleaning on a weekly basis es Do not clean with steel wool pads Do not use cleaners that are not specifically intended for stainless steel this includes glass tile and counter cleaners e If any surface discolors or rusting appears clean it quickly with Bon Ami or Barkeepers Friend Cleanser and a non abrasive cloth Always clean in the direction of the grain Always finish this process with Claire Stainless Steel Polish and Cleaner or comparable product to prevent further problems e Use of abrasive pads such as Scotchbrite will cause the
12. y Side Cut Out g 1 4 Space lt Between Appliances 02 2005 U U LINE CORPORATION 4 Prepare and Install Door Panel Black and White Units Only Two types of custom door panels can be installed on your Black or White unit to harmonize with or accent the surrounding d cor a Custom 1 4 Insert or a Full Overlay If no custom door panel is used go on to 5 Adjust Door Custom 1 4 Door Panel Insert Door Panel Preparation A custom door panel can be inserted into the doorframe Custom door panels can be flat or raised as long as the maximum panel thickness where inserted into the door reveal channel is 1 4 thick For raised panels the depth of the reveal is 1 4 on all four sides IMPORTANT Raised panels will reduce the door s 90 swing zero clearance if the unit is installed next to a wall or similar type of structure see Page 5 Cut the panel insert to the following dimensions Custom 1 4 Dimensions Width 23 1 32 Height 28 5 32 The door panel must not weigh more than 20 Ibs Door Panel Installation Install the insert as follows 1 Remove the door shelves by first pulling shelves up at a 45 angle then straight out see Figure 37 on Page 15 CAUTION Use care when handling the insert Insert edges may be sharp 2 Remove top hinge screw pin 7 64 Allen wrench or Phillips screwdriver depending on your unit s constructi
Download Pdf Manuals
Related Search