Electrolux Icon 48 Bottle Wine Cooler Free Delivery
Contents
1. Je wN Use amp Care Guide Wine Cooler A Electrolux 5995421657 2 Finding Information PLEASE READ AND SAVE THIS GUIDE Thank you for choosing Electrolux the new premium brand in home appliances This Use amp Care Guide is part of our commitment to customer satisfaction and product quality throughout the service life of your new wine cooler We view your purchase as the beginning of a relationship To ensure our ability to continue serving you please use this page to record key product information IMPORTANT PLEASE READ all instructions completely before attempting to install or operate the unit All wine coolers require a connection to an electrical power source Improper hook up can result in a safety hazard and potential damage to the product or contents Proper installation in accordance with the manufacturer s specifications and all local codes is the sole responsibility of the consumer The manufacturer is not responsible for any installation expenses or damages incurred due to improper installation If you are unsure of your ability to safely connect electric power to the unit consult a licensed and insured professional to perform all electrical work Once you have your unit installed we suggest you keep this manual in a safe place for future reference Should any problems occur refer to the Troubleshooting section of this manual This information will help you quickly identify a problem2. As Required 1 Disconnect power to the wine cooler 2 Remove racks if desired see WINE RACK REMOVAL INSTALLATION 3 Wipe down the interior with a solution of non abrasive mild detergent and warm water Rinse with clear water Reconnect power to the unit Condenser Cleaning Every 3 Months A WARNING Disconnect electric power to the unit before cleaning the condenser To remove and replace the grille for access to the condenser fins follow this procedure 1 Remove the control knob by grasping the knob and pulling straight off see Figure 25 2 Remove the screws at each end of the grille 3 Remove the grille Figure 25 A CAUTION DO NOT touch the condenser fins The condenser fins are SHARP The fins can also be easily damaged Clean the condenser coil using a brush or vacuum cleaner Do not touch Position the grille to align the screw holes with the cabinet Insert the grille screws and tighten being careful not to over tighten VG RR Install the control knob by aligning the flat of the control knob with the flat on the shaft Push firmly Maintenance 23 Wine Rack Removal Installation To remove the wine racks for cleaning 1 2 Grasp the end of the wine rack sliding it out and up Clean wine rack with a damp rag To insert the wine racks 1 Position the wine rack above the shelf channel where the rack is to be inserted See Figure 26 Slide the rack on the channel
3. 1 877 4ELECTROLUX 1 877 435 3287 For online support and Internet product information www electroluxusa com 4 Finding Information TABLE OF CONTENTS Finding Information eseesersersenvervesvenvesveserseener 2 Start p uenense keen 18 Please Read And Save This Guide ooooo0 2 Make A Record For Quick Reference ins 2 Temperature Control nn in eeseenesvesvesvrsvesersereenser 18 QUESTIONS sssseesssssessseesesseenesseetenseenenseen 3 TE EEE 20 Table Of Contents iunnvvonrvrrrrrerrerrerserrrrvrsersenser 4 Display Rack v v 20 Safety iinan testis beads nedeccapenece 5 Stocking Recommendations s ssesesssse 20 Important Safety Instructions esssseesseeeen 5 ME en 21 TELE ee RE 7 Maintaining Your Wine Cooler ssstssesseen 21 Exterior Cleaning s es 21 Site Preparation nesesemsessennestesnensosersennesnennenn 7 Stainless Steel smmeevrvvevvvvvrrrrvrrrrrervsrennns 21 i Interior Cleaning eeseessestestestestestesteseeseeseees 22 Wo d Trim ssecicscsscsceicscencsecscsccncunenrecewse coves eten vedk ven 9 Condenser Cleaning m m 29 Leveling inniinn 11 Wine Rack Removal Installation oooo 23 Bulb Replacement sisisi 23 Door Reversal mu uemmemiennevnreisnrevsneevesenvesene 12 i Troubleshooting n smssressressresrrnssersserssrsssensser 24 Door Adjustment neeseeresvrresvrresvrsererservrservenerner 14 If Service Is Required cccssssscsssssssssseesees
4. and get it remedied In the event you require assistance please contact the dealer where you purchased your unit MAKE A RECORD FOR QUICK REFERENCE Whenever you call to request information or service you will need to know your model number and serial number You can find this information on the serial plate located on the inside wall of your unit and on the product registration card 2004 Electrolux Home Products Inc Post Office Box 212378 Augusta Georgia 30917 USA All rights reserved Printed in the USA Finding Information 3 PRODUCT REGISTRATION GARD The package containing this manual also includes your product registration information Warranty coverage begins at the time your Electrolux wine cooler was purchased NOTE Registering your product with Electrolux enhances our ability to serve you You can register online at the Internet address below or by dropping your Product Registration Card in the mail Complete and mail the Product Registration Card as soon as possible to validate the registration date Please record the purchase date of your Electrolux unit and your dealer s name address and telephone number Purchase Date Electrolux Model Number Electrolux Serial Number Dealer Name Dealer Address Dealer Telephone Keep this manual and the sales receipt together in a safe place for further reference QUESTIONS For toll free telephone support in the U S and Canada
5. wood to ensure proper adhesion and durability of the finish To add a final finish coat 1 Remove five racks with wood trim from unit see RACK REMOVAL INSTALLATION Remove screws securing wood trim to racks Lightly scruff sand the molding with 280 grit 3M Tri M Ite amp sand paper Remove sanding dust with a clean dry cloth a RK WOW N Apply a thin coat of a clear protective finish the factory applied seal is compatible with virtually all finishes A low odor water clean up quick drying finish such as Minwax Polycrylic is recommended Follow container label for directions 6 Lightly sand and reapply if desired 10 Wood Trim To stain for a different wood color 1 Remove five racks with wood trim from unit see Rack Removal Installation Remove screws securing wood trim to racks Apply Minwax Water Based Wood StainQ to wood with a synthetic foam brush Stain must penetrate approximately 3 minutes After this period while stain is still wet take a stain dampened rag and remove all excess stain Wipe in the direction of the grain with medium pressure to achieve the desired stain color After 2 hours repeat step three This will even out the color of the wood Allow stain to dry for a minimum of 3 hours before finishing If desired sand the wood with very fine sandpaper to smooth the surface from the staining process Remove all dust from the wood Apply one coat of Minwax Ultra Fast Drying Polycrylic P
6. AC 60Hz 15A circuit normal household current 3 Avoid connecting the unit to a Ground Fault Interruptor GFI GFIs are prone to nuisance tripping which will cause the unit to shut down GFls are generally not used on circuits which power equipment that must run unattended for long periods of time 4 The unit must be installed according to your local codes and ordinances A DANGER ELECTROCUTION HAZARD Electrical Grounding Required This appliance is equipped with a three prong grounding polarized plug for your protection against possible shock hazards e NEVER remove the round grounding prong from the plug e NEVER use a two prong grounding adapter e NEVER use an extension cord to connect power to the unit Where a two prong wall receptacle is encountered or a longer power cord is required contact a qualified electrician to have it replaced in accordance with applicable electrical codes 8 Site Preparation NOTE All units require zero clearance when installed flush with a cabinet or wall see Figure 1 Electrolux stainless steel models require a minimum 2 3 4 inch handle clearance when installed against a wall or cabinet that extends beyond the front edge of the unit see Figure 2 CLEARANCE NEEDED UL124A 5 Position the unit to allow free air flow Figure 1 through the front grille see Figure 3 Lined Wipe out inside of unit with a damp cloth Final finish of the wooden wine rack trim must be applied a
7. FULL ONE YEAR One year from Pay all costs for repairing or replacing any parts of this Costs of service calls that are listed under WARRANTY original purchase appliance which prove to be defective in materials or NORMAL RESPONSIBILITIES OF THE date workmanship CONSUMER LIMITED 2rd 5TH Second through fifth Repair or replace any parts in the cabinet liner or sealed Costs for pickup and delivery of the appliance YEAR WARRANTY years from original refrigeration system compressor condenser evaporator required because of service Costs for labor parts Cabinet Liner and purchase date dryer or tubing which prove to be defective in materials or and transportation other than with respect to the Sealed System workmanship cabinet liner or sealed refrigeration system LIMITED Time periods listed All of the provisions of the full warranties above and the Costs of the technician s travel to the home and any WARRANTY above exclusions listed below apply costs for pick up and delivery of the appliance Applicable to the required because of service State of Alaska In the U S A your appliance is warranted by Electrolux Home Products Inc We authorize no person to change or add to any of our obligations under this warranty Our obligations for service and parts under this warranty must be performed by us or an authorized Electrolux Home Products Inc servicer In Canada your appliance is warranted by Electrolux Canada Corp NORMAL This wa
8. air or perform maintenance on the unit until the electricity has been disconnected e Altering cutting of power cord removal of power cord removal of power plug or direct wiring can cause serious injury fire and or loss of property and or life and will void the warranty e Do not lift unit by door handle A CAUTION e Failure to clean the condenser every three months can cause the unit to malfunction This could void the warranty Use care when moving the unit Some edges are sharp and may cause personal injury Wear gloves when moving or repositioning the unit Never install the unit behind closed doors Be sure front grille is free of obstruction Obstructing free air flow can cause the unit to malfunction and may void the warranty Allow unit temperature to stabilize for 24 hours before use A CAUTION e Use only genuine Electrolux replacement parts Imitation parts can damage the unit and may void the warranty Installation 7 INSTALLING THE WINE COOLER Your Electrolux wine cooler has been designed for either free standing or built in installation refer to the Built in Installation section of this manual for instructions In either case the front grille must NOT be obstructed SITE PREPERATION 1 Position the unit on a flat level surface capable of supporting the entire weight of the unit Remember the unit will be significantly heavier once it is fully loaded 2 This unit requires a grounded and polarized 115 V
9. an water Wipe with a soft clean towel to prevent water spotting Stainless Steel Models e Stainless steel models may discolor when exposed to chlorine gas pool chemicals salt water or cleaners with bleach Keep your stainless unit looking new by cleaning with a high quality all in one stainless steel cleaner polish on a monthly basis Frequent cleaning will remove surface contamination that could lead to rust Some installations will require cleaning on a weekly basis e DO NOT CLEAN WITH STEEL WOOL PADS e DO NOT USE CLEANERS THAT ARE NOT SPECIFICALLY INTENDED FOR STAINLESS STEEL this includes glass tile and counter cleansers e If any surface discolors or rusting appears clean it quickly with Bon Ami or Barkeepers Friend Cleanser and a non abrasive cloth Always clean in the direction of the grain Always finish this process with a high quality all in one stainless steel cleaner polish to prevent further problems e USE OF ABRASIVE PADS SUCH AS SCOTCHBRITE WILL CAUSE THE GRAINING IN THE STAINLESS TO BECOME BLURRED e Rust that is allowed to linger can penetrate into the surface of the stainless steel and become impossible to remove A CAUTION Stainless steel models exposed to chlorine gas and moisture such as areas with spas or swimming pools may have some discoloration of the stainless steel Discoloration from chlorine gas is normal Follow exterior cleaning instructions 22 Maintenance Interior Cleaning
10. at an angle until the rack is in the channel Continue sliding until the rack is all the way into the wine cooler Bulb Replacement To replace the light bulb in your wine cooler 1 Remove the light housing cover by sliding the cover towards the tab swinging the end opposite of the tab down and pulling down and away see Figure 27 Replace bulb with genuine Electrolux replacement Replace the light housing cover by inserting the tab FIRST and pushing up the other end You should hear a snap click Figure 26 Figure 27 24 Troubleshooting BEFORE YOU CALL FOR SERVICE If the unit appears to be malfunctioning read through Normal Operation first If the problem persists check the Troubleshooting Guide Locate the problem in the guide and refer to the cause and its remedy before calling for service The problem could be something very simple which can be solved without a service call Some remedies listed in the Troubleshooting Guide are very complex Consulting or contracting a qualified service technician may be necessary IF SERVICE IS REQUIRED Contact the dealer where you purchased the unit if service is required State the Model and Serial number and explain the problem The Model and Serial number plate is located inside the unit at upper right hand corner If you do not know the name of the selling dealer or local service company you can check online at www electroluxusa com or call 1 877 435 3287 Trou
11. bleshooting 25 TROUBLESHOOTING GUIDE A DANGER ELECTROCUTION HAZARD NEVER attempt to repair or perform maintenance on the unit until the main electrical power has been disconnected Troubleshooting What to check when problems occur Problem Possible Cause Remedy Unit not cold enough e Control set too warm e Turn control knob CLOCKWISE to set temperature colder Allow 24 hours for temperature to stabilize Check temperatures see introduction for specific e Light staying on e Check that light switch bracket contacts switch temperatures plunger e Airflow to front grille blocked e Airflow must not be obstructed to front grille See Installation e Dirty condenser coils Clean condenser See Maintenance e Door gasket not sealing properly e Adjust door gasket Unit too cold e Control set too cold e Turn control knob COUNTER CLOCKWISE to set temperature warmer Allow 24 hours for Check temperatures see temperature to stabilize introduction for specific temperatures No interior light e Loose or bumed out bulb e Tighten or replace bulb See Bulb Replacement Light won t go out when door is e Light on off switch is turned to ON Turn switch to OFF See Light Switch and Bulb closed 26 Warranty Information WINE COOLER WARRANTY Your wine cooler is protected by this warranty WARRANTY THROUGH OUR AUTHORIZED SERVICERS THE CONSUMER WILL BE PERIOD WE WILL RESPONSIBLE FOR
12. by services performed by servicers other than Electrolux Home Products Inc Electrolux Canada Corp or its authorized servicers use of parts other than genuine Electrolux Home Products parts obtained from persons other than such servicers or external causes such as abuse misuse inadequate power supply or acts of God 4 Products with original serial numbers that have been removed or altered and cannot be readily determined IF YOU NEED SERVICE Keep your bill of sale delivery slip or some other appropriate payment record The date on the bill establishes the warranty period should service be required If service is performed it is in your best interest to obtain and keep all receipts This written warranty gives you specific legal rights You may also have other rights that vary from state to state Service under this warranty must be obtained by contacting Electrolux Home Products Inc or Electrolux Canada Corp This warranty only applies in the 50 States of the U S A and Puerto Rico and Canada Product features or specifications as described or illustrated are subject to change without notice All warranties are made by Electrolux Home Products Inc In Canada your appliance is warranted by Electrolux Canada Corp USA Canada 877 435 3287 866 213 9397 Electrolux Home Products Inc Electrolux Canada Corp P O Box 212378 Augusta GA 30917 6150 McLaughlin Road Mississauga Ontario L5R 4C2
13. e testing period After 24 hours check the temperature of the water Adjust the control knob if necessary and retest UL320 Temperature Control 19 Your wine cooler is preset for a mid point setting 4 in order to achieve the recommended temperature range when installed in a 72 F ambient room temperature see Figure 21 Adjust the temperature gradually move the control knob in small increments and allow the temperature to stabilize For a warmer temperature move the knob towards Warmest counterclockwise lower number For a colder temperature move the knob towards Coldest clockwise higher number Figure 21 Factors which affect the internal temperatures of the cabinet include Temperature setting Room temperature where installed Number of times the door is opened and closed RA O N a Amount of time the internal light is illuminated This affects primarily wines on the top racks 5 Installation in direct sun light or near a heat source 20 Storage DISPLAY RACK JHS ENY The bottom rack in your wine cooler is designed for storage as well as for display purposes see Figure 22 4 m Model E24WC48E holds eight bottles in the display rack Figure 22 STOCKING RECOMMENDATIONS The wine racks allow for the proper horizontal stora
14. ge of wine The bottles are properly positioned so that the wine remains in contact with the cork to assure that the cork does not become dry Use the procedure listed below to stock your wine cooler White and sparkling wines should be maintained on the bottom to middle racks and red wine on the top racks A CAUTION The Anti tip brackets MUST be installed before you begin loading your wine cooler Your wine cooler models 2015WC and 2075WC Delete parenthetical should be stocked beginning with the bottom display rack at the back and work forward Stagger the bottles as shown in Figure 23 Subsequent racks should be stocked similarly starting with the back of each rack see Figure 24 Figure 24 A elle i k ij PTR PN O OH O WW O T IE F Is if alt if IA 1 al Maintenance 21 MAINTAINING YOUR WINE COOLER Periodic cleaning and proper maintenance will ensure efficiency top performance and long life The maintenance intervals listed are based on normal conditions You may want to shorten the intervals if you have pets or other special considerations Exterior Cleaning As Required The door grille and cabinet may be cleaned with a mild detergent and warm water solution Do not use solvent based or abrasive cleaners Use a soft sponge and rinse with cle
15. r see Figure 9 Do Figure 6 not discard PLASTIC PLUGS Figure 8 Figure 9 Door Reversal Remove top hinge 3 screws reinstall hinge screw pin and remount on opposite side BOTTOM see Figure 10 Remove the two door closer plastic inserts from the existing bottom hinge and install as shown on the new bottom hinge see Figure 11 Remove existing bottom hinge 3 screws and remount on opposite side TOP Remove top hinge screw pin With bottom of door facing up remove pivot plate 2 screws flip over and remount on opposite side of door see Figure 12 Holding door upright with top of door tilted forward place hole of door pivot plate on bottom hinge screw pin see Figure 13 Be sure that the bosses on the closers align with holes in hinge and hinge plate Tilt top of door into position in top hinge and install top hinge screw pin In empty hinge holes install plastic screw plugs 3 top and 3 bottom and door hole plug 1 door top removed in step 2 13 HINGE 7 SCREW Figure 10 INSERTS Figure 11 Figure 12 CLRCO008 UL319 14 Door Adjustment ADJUSTING THE DOOR Your door is aligned at the factory before shipment Occasional re adjustment may be necessary especially if an overlay panel is installed The following procedure will correct for up to 1 4 alignment The door should never be flush with the top of the cabinet Even when le
16. rotective Finish with a synthetic foam brush to the wood This finish should be applied in a thin coat following the direction of the grain First apply the finish to the back and sides of the wood Allow this to dry for two hours Next apply the finish to the front side of the wood and allow to dry for two hours Sand with very fine sandpaper 220 grit Reapply in the same manner 3 times total After the third coat do not sand the surface Allow the final coat to dry for 24 hours before installing the wood to the wine cooler racks Leveling 11 LEVELING THE UNIT Position the unit on a flat level surface capable of supporting the entire weight of the unit when full This unit contains four adjustable leveling legs Turn the legs clockwise to raise and counterclockwise to lower see Figures 4 and 5 Figure 4 Figure 5 12 Door Reversal REVERSING THE DOOR E E a AE BE E E BE BE BE E All Electrolux wine cooler models are field reversible for left or right hand opening The door opening is easily reversed by moving the hinge hardware to the opposite side see Figure 6 To reverse the door 1 Remove top hinge screw pin 7 64 Allen wrench from cabinet see Figure 7 Remove door by tilting forward and lifting off bottom hinge pin 2 Remove plastic screw plugs 3 top and 3 bottom from new hinge location see Figure 8 and remove hinge pin hole plug in top of doo
17. rranty applies only to products in ordinary household use and the consumer is responsible for the items RESPONSIBILITIES listed below OF THE CUSTOMER 1 Proper use of the appliance in accordance with instructions provided with the product 2 Proper installation by a licensed and insured professional in accordance with instructions provided with the appliance and in accordance with all local plumbing electrical and or gas codes 3 Proper connection to a grounded power supply of sufficient voltage replacement of blown fuses repair of loose connections or defects in house wiring 4 Expenses for making the appliance accessible for servicing such as removal of trim cupboards shelves etc which are not a part of the appliance when it was shipped from the factory 5 Damages to finish after installation 6 Replacement of light bulbs and or fluorescent tubes on models with these features EXCLUSIONS This warranty does not cover the following 1 CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN OR ANY IMPLIED WARRANTY Note Some states do not allow the exclusion or limitation of incidental or consequential damages so this limitation or exclusion may not apply to you 2 Service calls which do not involve malfunction or defects in workmanship or material or for appliances not in ordinary household use The consumer shall pay for such service calls 3 Damages caused
18. see 24 Built in Installation vu umessnnnsmmesneisene 16 Warranty Information sueeerevevvoeesssssvvv 26 Operaatio irsinin 17 The Right Temperature for Wine s es 17 Proper Storage siiis 17 Control Settings 17 Light Switch and Bulb oceans 17 IMPORTANT SAFETY INSTRUCTIONS Safety Precautions Do not attempt to install or operate your unit until you have read the safety precautions in this manual Safety items throughout this manual are labeled with a Danger Warning or Caution based on the risk type Definitions This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death A DANGER DANGER indicates an imminently hazardous situation which if not avoided will result in death or serious injury A WARNING WARNING indicates a potentially hazardous situation which if not avoided could result in death or serious injury A CAUTION CAUTION indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury IMPORTANT Indicates installation operation or maintenance information which is important but not hazard related 6 Safety General Precautions A DANGER RISK OF CHILD ENTRAPMENT Before you throw away your old appliance take off the doors and leave shelves in place so that children may not easily climb inside A WARNING e Never attempt to rep
19. t least 24 hours before re installing the wooden rack trim into the cabinet oni 8 Be sure to install the Anti Tip brackets DOOR E Follow the instructions provided with the SWING ea Anti Tip bracket kit She lt 2 314 ni CLEARANCE NEEDED 1 LL Figure 2 INTAKE EXHAUST Figure 3 WoodTrim 9 WINE RACKS WITH WOOD TRIM Your Electrolux wine cooler is equipped with a natural wood trim on the wine racks for appearance and durability The wood trim has been coated at the factory with a clear vinyl sealer which will adequately protect the wood in normal usage A CAUTION To prevent permanent damage to the inner liner of your wine cooler the wine rack wood trim MUST be removed from the unit for staining and or finishing Allow stain finish to dry thoroughly at least 24 hours per coat in accordance with the stain finish manufacturer s instructions prior to re installing the wood trim inside the cabinet of the wine cooler Failure to do so may cause the inner liner of the unit to have a permanent odor which is not covered by the warranty You have 3 options regarding the wood trim on the wine racks 1 You can leave as is 2 add a final finish coat or 3 you may stain the wood trim The final finish coat was not applied at the factory so that the wood trim could be stained YOU CANNOT STAIN THE WOOD TRIM ONCE YOU APPLY THE FINAL FINISH Review the following guidelines when staining and or sealing the
20. uire additional air space for top sides or rear However the front grille must NOT be obstructed NOTE To ease unit installation and removal it is recommended that the cabinet rough opening dimensions be increased by at least 1 4 over the dimensions given for your unit Unit Dimensions Tor tee a E24WC48E 23 15 16 34 ET 23 ET i See Figure 18 for dimensions in inches and millimeters Figure 18 22 1516 _ p 60 6 34 1 8 86 7 FULL RETRACT HEIGHT Operation 17 THE RIGHT TEMPERATURE FOR WINE Your Electrolux wine cooler has a unique triple temperature zone permitting storage of your finest wines at approximately 60 F 15 C in the top portion of the cabinet for reds 50 55 F 10 12 C in the middle for whites and 45 F 7 C on the bottom for sparkling wines Temperatures noted are product temperatures and not air temperatures PROPER STORAGE Model E24WC48E will accommodate 48 bottles 750 ML size Specially designed wine racks allow for proper horizontal storage of the wine The cork remains moist which keeps air from entering the bottle CONTROL SETTINGS Your wine cooler is shipped in the ON position however you may turn it ON or OFF using the control knob CONTROL KNOB located in the center of the grille Turn the control knob clockwise for ON counterclockwise for OFF To turn the unit OFF rotate the control knob co
21. unterclockwise all the way toward LIGHT warmer until it stops until click is heard The ON OFF DOOR Ea ON OFF SWITCH SWITCH MITT switch located to the right of the control knob is used to turn the inside light on and off see Figure 19 LIGHT SWITCH AND BULB Your wine cooler has an interior light that is illuminated when the door is opened If you wish to display your wines for those special occasions while the door is closed just depress the switch located to the right of the control dial on the grille to the ON position Please note when the light is on for an extended period of time it will increase the cabinet temperature especially at the top 18 Figure 20 Start up and Temperature Control STARTING THE UNIT Electrolux wine coolers are designed to provide different temperature zones within the cabinet so different types of wine may be maintained at varying temperatures The coolest temperature is at the bottom and the warmest is at the top of the cabinet ADJUSTING THE TEMPERATURE CONTROL E E E E E BE E a E To accurately check the temperature insert an reliable thermometer into a plastic non breakable bottle partially filled with water Tighten the bottle cap securely see Figure 20 Place the bottle in the desired area for 24 hours Refrain from opening the unit during th
22. vel the top edge of the door will be 1 8 below the top of the cabinet see Figure 14 To adjust Figure 14 1 Compare the top edge of the door opposite the hinges to the top edge of the cabinet and note the type up or down of adjustment needed Remove the top hinge pivot pin with a 7 64 hex wrench see Figure 15 and lift door off bottom hinge pin Be careful not to lose door closers see Figure 17 With door upside down loosen but do not remove the two hinge plate screws Figure 15 4 Door Adjustment 15 If door edge opposite the hinges needs to move up move plate toward outside of door If door edge needs to move down move plate toward inside of door see Figure 16 Repeat until top edge of door is parallel with top of cabinet and tighten screws securely After adjustment is complete remove the door closers from the bottom hinge clean thoroughly and apply petroleum jelly to the mating surfaces of the closers see Figure 17 Be sure that bosses on closers align with holes in hinge and hinge plate Mount door and install top hinge pivot pin Figure 16 Z SLOTTED MOUNTING HOLES NOTCH ee RAISE gt LOWER OUTSIDE OUTSIDE DOOR EDGE DOOR EDGE CLRCO001a Figure 17 16 Built In Installation INSTALLING A BUILT IN Your Electrolux wine cooler has been designed for either free standing or built in installation When built in your wine cooler does not req
Download Pdf Manuals
Related Search