Hoover U5750-900 WindTunnel Bagless Upright Vacuum
Contents
1. following directions in The belt section beginning with Fig 3 17 Discard old agitator Continue following the directions in The belt section to reposition belt new agitator and bottom plate 11 Powered hand tool some models only Agitator brush roll replacement When agitator brush roll brushes are worn the brush roll should be replaced Ask for HOOVER part No 48414088 2 Unscrew the two Phillips screws and 3 Remove agitator including end plates remove belt guard B C and discard 4 Inspect belt to ensure that it is in good condition If belt is cracked gouged or broken replace it see follow ing section 5 Insert brush roll through belt and posi tion belt over gear teeth D on brush roll How to replace 1 Remove tool from hose and turn it so bottom faces up Press the latches on either side of tool and remove bottom plate A 6 With curved ends down slide end 7 Replace belt guard B making sure 8 To replace bottom plate A insert the plates C of brush roll into slots E on not to pinch brush bristles in guard Turn four tabs on edge of bottom plate into tool agitator making sure it rotates freely slots on front of tool Replace and tighten screws Pivot bottom plate down and snap closed Powered hand tool Replacing belt Belt replacement When replacing belt ask for HOOVER Inspecting the belt part No 38528037 The powered hand tool belt is designed eee2. should be checked from time to time to be sure it is in good condition When to replace Disconnect cleaner from electrical outlet To check belt remove bottom plate as shown in How to replace Replace belt if it is stretched cut or broken What to buy To assure effective operation use only genuine HOOVER belts with your cleaner When purchasing a new belt ask for HOOVER part No 38528033 10 Headlight replacement What to buy This cleaner uses a 12 volt wedge base type 912 bulb HOOVER part No 27313101 Replacing lens Reposition lens and secure with the two Screws How to replace Disconnect cleaner from electrical outlet Place handle in low position and turn cleaner over so bottom side is up Remove the 4 screws as shown with a Phillips screw driver Lift off bottom plate A Removing lens Disconnect cleaner from electrical outlet Using a screwdriver remove the two screws as shown and lift off lens Removing belt Remove agitator brush roll and used belt Discard used belt Installing new belt With lettering on outside of belt and positioned as shown in box on D slide new belt over motor pulley B Replacing bottom plate Reposition bottom plate and 4 Phillips head screws Tighten screws securely The edge groomers When to replace The edge groomers located on both sides of the nozzle should be replaced when they appear worn What to buy When
3. Service Dealers Depots For an automated referral of authorized service outlets in the U S A phone 1 800 944 9200 OR visit The Hoover Company on line at www hoover com This warranty does not cover pick up delivery or house calls however if you mail your appliance to a Hoover Factory Service Center for warranty service transportation will be paid one way While this warranty gives you specific legal rights you may also have other rights which vary from state to state or province If further assistance is needed or if there are questions concerning this warranty or the availability of warranty service outlets write or phone the Consumer Response Center The Hoover Company 101 East Maple St North Canton Ohio 44720 Phone 330 499 9499 In Canada contact Hoover Canada Burlington Ontario L7R 4A8 Phone 1 800 263 6376 15
4. aa ease FI ial to last a long time and is not normally through 3 27 replaced However if the belt is crack ed gouged or broken it should be replaced 4 With flat sides of turbine retainers G pointing down slide retainers into grooves H in tool housing and snap into place 5 Replace brush roll belt guard and bottom plate as described in Figs 3 27 through 3 30 2 Grasp turbine E and pull firmly to The belt can be seen through the top of remove the nozzle or by removing the bottom plate and belt guard Figs 3 25 and 3 26 12 3 Remove belt from turbine pulley F Replace with new belt Lubrication The motor is equipped with bearings that contain sufficient lubrication for the life of the motor The addition of lubricant could cause damage Therefore do not add lubricant to motor bearings The agitator is equipped with two ball bearings that should be lubricated periodically by a Hoover Factory Service Center or an Authorized Hoover Warranty Service Dealer Depot Thermal protector An internal thermal protector has been designed into your cleaner to protect it from overheating When the thermal protector activates the cleaner will stop running If this happens proceed as follows 1 Turn the cleaner OFF and discon nect it from the electrical outlet 2 Check dirt cup pre filter HEPA cartridge filter and secondary and final filters for dirt accumulation 3 Refer to Clea
5. children acorn eer Sram Do not allow vacuum cleaner A be used a Ae or to run Unattended at any time LUDFICATION o assssssscesessessssssssssssssseeeeesee 13 Keep hair loose clothing fingers feet and all parts of body away from openings Maintenance rotating agitator and other moving parts Do not operate cleaner in bare feet or Authorized Service ccese 13 when wearing open toe shoes or sandals Cleaning filters ssesecese e 8 9 Do not pick up anything that is burning or smoking such as cigarettes matches or Emptying Dirt Cup s s sessee ee e 8 hot ashes Replacing Agitator Brush Roll 11 Do not use to pick up flammable or combustible materials such as gasoline or fine Replacing Power Hand Tool wood sandings or use in areas where they may be present Agitator Brush Roll 00 12 e Avoid picking up hard sharp objects with the cleaner They may damage the Replacing Belt sccsseeee 10 11 cleaner Replacing Power Hand Tool Belt 12 e Always turn off this appliance before connecting or disconnecting hose Replacing Edge Groomers 11 Do not use without dirt cup or filters in place Empty cup and clean filter frequently Replacing Headlight cuGcdumsansasuceesueseas 10 when picking up very fine materials such as powder Thermal Protector csseceseeeeeeees 13 Use extra care when cleaning on stairs Warranty oina 14 Do not put any object into
6. pre filter as described in Filter assembly section e Dirt cup not properly installed and latched e Position dirt cup properly and lock latch Fig 3 4 e Dirt cup lid not positioned properly or missing e Ensure that dirt cup lid is properly positioned e Filter assembly not assembled properly e Ensure that filter assembly is positioned properly Figs 3 8 to 3 10 Problem Cleaner hard to push Possible cause Possible solution Incorrect carpet height setting e Move nozzle control knob to a higher setting P ro bl em Cleaning tools won t pick up Possible cause Possible solution e Cleaner handle not in upright position e Ensure that cleaner handle is locked in upright position Blockage in hose e Clear blockage Problem Visible dirt leaking through final filter Possible cause Possible solution Filter assembly not installed properly e Remove filter assembly from dirt cup and ensure that HEPA cartridge filter is properly attached to pre filter screen and that entire filter assembly is properly repositioned inside dirt cup Figs 3 5 through 3 10 Problem Dirt inside dirt cup stops spinning Note Heavy debris may settle to the bottom of the dirt cup and prevent the dirt from spinning without affecting cleaning performance The cleaner can continue to be used even if the dirt is not spinning inside the dirt cup However if the dirt does stop spinning AND there is a not
7. to return clean air to the room To remove this filter when it becomes dirty open the door on the side of the cleaner Lift out filter K and hand wash it in cold water with mild detergent lt is recommended that the HEPA cartridge filter be cleaned by tapping either of the ends DO NOT tap soft pleated sides of HEPA cartridge filter as this could damage the filter Tap filter until no more dust particles fall from the filter Slide filter assembly down into cup until a light snap is felt Gently pull up on assembly to ensure that it is seated properly in the cup Ensure that no part of pre filter screen extends above top edge of dirt cup Replace lid and return cup to cleaner Fig 3 4 Let filter air dry and reposition it on the side of cleaner Make sure the white side of the filter faces outward Close door Should you want to replace this filter ask for HOOVER part No 40110006 Do not operate cleaner without any of the filters in place To re assemble filter assembly place large knob of HEPA cartridge filter in hole on bottom of pre filter Snap top of HEPA cartridge filter into place Secondary and final filters Cleaning secondary filter Disconnect cleaner from electrical outlet The secondary filter J located behind the grill in the bottom of cleaner cavity protects the motor from dirt particles If the filter becomes dirty remove dirt cup Fig 3 2 Remove screw and pul
8. D COON 10 11 12 13 15 16 17 18 19 Polarized plug ON OFF switch To reduce the risk of electric shock this Plug cord into electrical outlet appliance has a polarized plug one To turn cleaner ON push switch blade is wider than the other This plug To turn cleaner OFF push switch will fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a qualified electrician to install the proper outlet Do not change the plug in any way Handle ON OFF switch Tool cover Dusting brush Powered hand tool or Crevice tool depending on model Furniture nozzle Dirt cup latch Dirt cup lid 9 Dirt cup Dirt cup handle HEPA cartridge filter Pre filter Final filter 14 Three position handle release pedal step on lever to lower handle to operating or low positions 20 Hose rack 21 Cord hooks wrap cord around hooks for storage The top hook can be rotated right or left for easy cord release 22 Carrying handle 23 Extension wands 24 Crevice wand stores in rear wand Some models only Operate cleaner only at voltage specified on data plate on bottom of cleaner This cleaner is intended Nozzle control knob slide fOr household use knob to correct setting for height of carpet being cleaned Furniture guard Headlight Edge groomers Hose up down T
9. WindTunnel Bagless by Hoover Congratulations on your purchase This product was designed for easy assembly see page 3 Owner s Manual Review this manual before ENGLISH gt pp 1 14 operating cleaner ESPANOL pag 16 23 FRAN AIS p 24 31 Fill in and retain The model and serial number are located on the bottom of the cleaner For your personal records please enter the COMPLETE model and serial number in the spaces provided and retain this information Yourcleanerismodels ses s i it wore and has serial number woos UEAB5 000 seee MAZ a aa a a aaa o BELT ie lt is suggested that you attach your sales receipt to this owner s manual cnvawomaucon n GBo POUR UN USAGE M NAGER UNIQUEMENT Ppa A Fabrique aux U Verification of date of purchase may be required for warranty service of your HOOVER product Important Safeguards When using an electrical appliance always follow In d ex basic precautions including the following Assembling Cleanet 2 010 3 4 READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE Carton Content c ccssscssesssssssesseesens 3 Cl D IDUON Sa 5 n oa e io e s5 Warning to reduce the risk ot tire electric shock or injury Cleaning Tools s ccccssseeeeees l o D onotuse outdoor oronwersuraces If You Have a Problem 05 13 14 Close supervision is necessary when any appliance is used by or near
10. al outlet 1 Look into hose end and remove any blockage 2 Check lower dirt duct for blockage Fig 4 1 C If a blockage occurs during powered hand tool use some models only 1 Disconnect powered hand tool from hose Remove bottom plate belt guard and turbine as described in Figs 3 25 3 26 and 3 33 Remove any blockage from turbine channel D Replace belt turbine brush roll belt guard and bottom plate Full One Year Warranty Domestic Use Your HOOVER appliance is warranted in normal household use in accordance with the Owner s Manual against original defects in material and workmanship for a period of one full year from date of purchase This warranty provides at no cost to you all labor and parts to place this appliance in correct operating condition during the warranted period This warranty applies when the appliance is purchased in the United States including its territories and possessions or in Canada or from a U S Military Exchange Appliances purchased elsewhere are covered by a limited one year warranty which covers the cost of parts only This warranty does not apply if the appliance is used in a commercial or rental application Warranty service can only be obtained by presenting the appliance to one of the following Authorized Warranty Service outlets Proof of purchase will be required before service is rendered 1 Hoover Factory Service Centers 2 Hoover Authorized Warranty
11. d hand tool wipe off dirt with a cloth dampened in a mild detergent Rinse with a damp cloth Do not submerge powered hand tool in water Cleaning tools may be washed in warm water with a detergent Rinse and air dry before using Extra reach hose Push ON OFF switch to OFF position Remove regular hose from cleaner Align end of extra reach hose with projections M over slots N in dirt duct Familiarize yourself with these home maintenance tasks as proper use and care of your cleaner will ensure contin Dirt cup The dirt cup assembly consists of the following parts Lid A Dirt Cup B Pre filter C HEPA Cartridge Filter D Dirt Inlet Opening E While the cleaner is in operation the pre filter screen will stop larger debris from entering the HEPA cartridge filter chamber This larger debris will be seen collecting in the left side of the dirt cup The HEPA car tridge filter will collect fine particles that have passed through the pre filter screen Replace dirt cup lid Slide cup straight into cleaner cavity Bottom of cup will rest behind grooves at bottom of cleaner cavity G Push latch F to the right to lock in place When to empty It is recommended that the dirt cup be emptied before the dirt reaches the dirt inlet opening on back of dirt cup Fig 3 1 or after every use if preferred CAUTION Very fine materials such as face powder cornstarch or fire place soot may sea
12. iceable decrease of performance check the items under Cleaner won t pick up Problem Powered hand tool some models brush roll won t turn Possible cause Possible solution Too much pressure being applied to tool e Continue using tool applying light pressure Blockage in turbine channel e Remove blockage Continued 13 Broken or worn belt e Replace belt e Low cleaner suction e Check items under Cleaner suction low Clearing blockages Disconnect cleaner from electrical outlet Low suction or pick up may be due to a blockage in the system Refer to the fol lowing steps to check for blockages continuing with each step until the blockage is found A If a blockage occurs during floor cleaning Turn cleaner OFF and disconnect from electrical outlet 1 Check fullness of dirt cup and filter assembly empty cup and clean filters if needed Check dirt duct 2 Remove screws on lower back of cleaner handle A and remove lower dirt duct B 3 Clear blockage from dirt duct sections Checking under bottom plate 4 Turn cleaner OFF and unplug 5 Remove bottom plate belt and agitator see The belt section Look into opening C for blockages and remove 6 Remove agitator shield see Fig 3 20 and remove any loose debris which may have accumulated under it 14 B If a blockage occurs during tool use Turn cleaner OFF and disconnect from electric
13. l grill out Lift out filter Hand wash filter in cold water with mild detergent then air dry Reposition dry filter grill and screw Replace dirt cup Should you want to replace this filter ask for HOOVER part No 38762008 Reattaching filter door The filter door is designed with a break away feature which allows it to snap free if it is pushed open too far To reattach align hinges L of cover with slots on sides of filter area Press door back into place Continued 9 Check agitator shield Because your cleaner picks up so well we strongly recommend you check for debris accumulation under the agitator shield each time you clean the filters Removing debris under the shield will help maintain your cleaner s excellent pick up and suction Remove debris as follows 1 Disconnect cleaner from electrical outlet 2 Check for dirt accumulation by removing bottom plate Fig 3 17 removing agitator Fig 3 18 and lifting agitator shield Fig 3 20 3 Remove any debris and replace shield agitator and bottom plate Figs 3 20 to 3 22 Installing bulb Pull old bulb straight out of socket Push new bulb straight into socket until locked in place Excessive force is not required Belt replacement The belt on your HOOVER cleaner causes the agitator to rotate and is important for the effective operation of the cleaner The belt is located under the bottom plate of the cleaner and
14. l the filter and cause loss of suction When using the cleaner for this type of dust empty the cup and clean the filters often Sm How to empty Disconnect cleaner from electrical outlet Do not use cleaner without dirt cup or filters in place Push latch F to the left to unlock Lift cup slightly and pull straight out to remove from cleaner Filter assembly The HEPA cartridge filter and pre filter are essentially self shedding Tapping the side of the dirt cup as described in How to empty dirt cup should sufficiently remove dust and fine particles from the HEPA cartridge filter and pre filter The filter assembly can also be removed for additional cleaning Remove lid Note It is not necessary to remove the HEPA cartridge filter to empty the dirt Cup Tap side of cup until no more dust particles fall from the HEPA cartridge filter How to clean filter assembly Remove dirt cup and dirt cup lid as described in How to empty dirt cup Grasp pre filter frame and pull up firmly Slide filter assembly out of cup Grasp end of HEPA cartridge filter and pull it away from pre filter Remove cartridge from assembly The pre filter C can be cleaned with a brush and then rinsed with water Allow pre filter to dry thoroughly H on pre filter frame with grooves I in dirt cup Align grooves Cleaning final filter The final filter assists in the filtration process
15. openings Do not use with any opening blocked keep free of dust lint hair or anything that may reduce air flow Do not pull or carry by cord use cord as a handle close door on cord or pull cord around sharp edges or corners Do not run appliance over cord Keep cord away from heated surfaces UL S A B Always disconnect cord from electrical outlet before servicing the cleaner Unplug cleaner when not in use Turn off all controls before unplugging Do not unplug by pulling on cord To unplug grasp the plug not the cord N ever handle plug or appliance with wet hands The use of an extension cord is not recommended Do not use with damaged cord or plug If appliance is not working as it should has been dropped damaged left outdoors or dropped into water take it to a Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer Depot 2000 The Hoover Company Use vacuum cleaner only for its intended use as described in the instructions Use only attachments recommended by The Hoover Company jothers may cause www hoover com hazards Save these instructions 1 Assembling cleaner This cleaner was inspected and packaged carefully before being shipped from the factory If you should happen to need assistance during assembly or operation call 1 800 944 9200 for an automated referral of service outlet locations U S only OR 1 330 499 9499 to speak with a representative in our Consumer Response Center OR Visit u
16. ormance of Hoover uprights only and not for comparison with any other brands The majority of this rating is based upon the American Society for Testing and Materials ASTM Carpet Cleaning Effectiveness Test ASTM Test F608 Other performance factors include Hose Power ASTM Test F558 Surface Litter Cleaning Hard Floor Cleaning Edge Cleaning Cleaning Width and Air Filtration 4 If you have a problem If a minor problem occurs it usually can be solved quite easily when the cause is found by using the check list below Problem Cleaner won t run Possible cause Possible solution Not firmly plugged in e Plug unit in firmly e No voltage in wall plug e Check fuse or breaker e Blown fuse or tripped breaker e Replace fuse or reset breaker e Thermal protector activated e Allow cleaner to cool for 30 minutes this will reset the thermal protector see pg 13 Problem Cleaner won t pick up Possible cause Possible solution Broken or worn belt Replace belt e Agitator brush roll worn e Replace brush roll e Dirt cup full e Empty dirt cup e Incorrect carpet height setting e Move nozzle control knob to lower setting e Blockage in air flow passage e Clear blockage e HEPA cartridge filter clogged e Clean HEPA cartridge filter by either tapping the side of the dirt cup or removing the cartridge filter as de scribed in the Filter assembly section e Pre filter clogged e Clean
17. purchasing edge groomers ask for HOOVER part No 39511004 How to replace Disconnect cleaner from electrical outlet Remove bottom plate as described in The belt section Fig 3 17 Replacing agitator brush roll Insert agitator through belt and place belt in belt guide C on agitator Should the agitator shield D become dislodged while replacing the belt or the agitator reposition it as shown noting the placement of its belt guide E The agitator brush roll When to replace When agitator brushes are worn the agitator should be replaced To check condition of brushes discon nect cleaner from electrical outlet Move edge of a card across bottom plate while turning agitator To maintain cleaning effectiveness replace agitator if brushes do not touch card What to buy When purchasing a new agitator ask for HOOVER part No 48414115 Installing groomers Lift off both old edge groomers and slide new edge groomers into position as shown Reposition bottom plate and secure with 4 Phillips head screws Securing agitator Grasp agitator firmly and fit it into posi tion by first sliding end opposite the belt into the rectangular slot F on side of cleaner Pull other side of agitator G into place Turn agitator making sure belt is not pinched between agitator and agitator shield How to replace Disconnect cleaner from electrical outlet Remove bottom plate belt and agitator
18. ransporting cleaner Carrying cleaner To move your cleaner from room to The cleaner can also be moved by room put handle in upright position tilt using the carrying handle cleaner back on rear wheels and push forward Handle positions The handle of your cleaner has three positions upright for storage and when using cleaning tools operating posi tion for general operation on carpet and floors low for reaching under low furniture Step on handle release lever to lower handle Continued 5 M V W FE F ge Carpet height adjustment The cleaning of carpet and rugs takes place at the nozzle A When it is necessary to raise and lower the nozzle for various carpet pile heights slide the nozzle control knob B to the desired setting Handle position For ease in sliding knob the handle should be in the upright position C The nozzle will not move into the adjusted position until the cleaner handle is lowered to the operating position D Settings For maximum cleaning performance the following carpet height settings are recommended e Lowest setting for bare floors and all types of carpet Note If the cleaner is difficult to push slide knob to the next higher setting e Higher settings for very deep pile carpet where easier pushing effort is desired while maintaining good cleaning perfomance Cleaning lightweight flexible rugs Stand on one end of rug and move cleaner towa
19. rd other end or edge Before reaching edge push down on handle This will lift up the nozzle front of cleaner and will prevent rug from clinging to cleaner Continue to lift up nozzle so that when you have reached the edge it is completely off the rug Move cleaner back to start again lower nozzle and use only forward strokes Edge cleaning Special edge groomers are provided on both sides of the nozzle to remove dirt in carpet near baseboards and furniture Guide either side of nozzle parallel to edge of carpet or furniture Stair cleaning Use the hose and powered hand tool or furniture nozzle for stair cleaning Clean from bottom to top When using cleaning tools the agitator will continue to rotate CAUTION To avoid personal injury or unnecessary wear to carpet and to prevent the cleaner from falling always place it at bottom of stairs some models only Cleaning tools Tools allow for cleaning surfaces above the floor and for reaching hard to clean areas Handle must be in the upright posi tion for tool use CAUTION Agitator continues to rotate while cleaner handle is in upright position Avoid tipping cleaner or setting it on furniture fringed area rugs or carpeted stairs during tool use How to attach tool cover The tool cover is designed with a break away feature which allows it to snap free if it is pushed open too far To reattach align hinges of cover with slots on sides of
20. ring blockages section 4 When cleaner is unplugged and the motor cools for 30 minutes the thermal protector automatically resets and cleaning may continue If the thermal protector continues to activate after following the above steps your cleaner may need servicing see Service section Service To obtain approved HOOVER service and genuine HOOVER parts locate the nearest Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer Depot by e checking the Yellow Pages under Vacuum Cleaners Household OR e checking the list of Factory Service Centers provided with this cleaner OR e calling 1 800 944 9200 for an automated referral of authorized service outlet locations U S only OR e checking the Service section of The Hoover Company on line at www hoover com Do not send your cleaner to The Hoover Company in North Canton for service this will only result in delay If further assistance is needed contact The Hoover Company Consumer Response Center North Canton Ohio 44720 Phone 330 499 9499 In Canada contact Hoover Canada Burlington Ontario L7R 4A8 Phone 1 800 263 6376 Always identify your cleaner by the complete model number when requesting information or ordering parts The model number appears on the bot tom of the cleaner Hoover Cleaning Performance This Hoover Cleaning Performance Sys tem is for comparing the relative pro gressive perf
21. s on line at www hoover com to find the service outlet nearest you click on the Service button Carton contents Remove all parts from carton and identify each item shown Make sure all parts are located before disposing of packing A Handle section oe Note The white switch lock above the ON OFF switch aids in B Cleaner body the assembly of your cleaner Assembly can be continued if C Hose cleaning tools and wands the switch lock is missing However do not remove the switch packed on cleaner lock until assembly is completed D Powered hand tool some models Continued STEP 1 Attach handle Remove cardboard A and screws from handle section Discard card board Slide handle section onto back of handle Push screws into holes on back of handle Tighten screws securely with a Phillips screwdriver Remove powered hand tool some models from plastic bag and return it to the tool storage area Open tool cover on cleaner body Make sure that the switch is in the B OFF position Remove powered hand tool some models Remove switch lock C above ON OFF switch D by pulling it straight out Dispose of switch lock If switch lock has come off during assembly make sure switch is in OFF position down before plug ging into electrical outlet 2 H OW to use The assembled cleaner will look like the drawing Model with Powered Hand Tool is shown Cleaner description oF N
22. tool storage area Push cover down to secure in place I Powered hand tool may be used for upholstered furniture carpeted stairs and hard to reach places J Crevice tool may be used in tight spaces corners and along edges in such places as dresser drawers uphol stered furniture stairs and baseboards K Crevice wand can be used in tight spaces corners and along edges in such places as dresser drawers uphol stered furniture stairs and baseboards It can also be used for extra reach with the dusting brush and or extension wand Select proper tool G Dusting brush may be used for carved furniture table tops books lamps lighting fixtures venetian blinds baseboards shutters and registers H Furniture nozzle may be used for upholstered furniture draperies mat tresses clothing automobile interiors and carpeted stairs L Wands are used to give extra length to your hose Use them with any of the above tools some models Slide hose into N and twist hose to lock it into place To detach hose reverse procedure Attach wands or tools to the other end of hose Available at additional cost if not includ ed with your cleaner Attach wand and tools Attach tool or wand to the hose E Attach second wand or tool to wand F by pushing it firmly onto the wand Twist wand or tool slightly to tighten or loosen the connection How to clean tools To clean the hose and the powere
Download Pdf Manuals
Related Search