Home
Zipper Mowers 309-365 Automobile Parts User Manual
Contents
1. FUNDER MAX made simple EFI Thank you for purchasing a ThunderMax ECM Please read through the following instructions before beginning the installation procedure Following these instructions will ensure that the ECM is installed and setup properly for optimal results If you have any problems or questions please refer to the SmartLink Tuning pdf Manual included on the CD Help Menu with this package Step 1 Insert the SmartLink CD into your computer SmartLink will automatically open the InstallShield Wizard when the computer finds the CD Rom Follow the instructions and install the software on your computer If you do not have a serial port on your computer for the communication cable you will need to use a USB to Serial converter an inexpensive converter is available from Zipper s 372 000 Install the included driver disc at this time follow the instructions given by the manufacturer of the converter for installation For online updates visit Step 2 Install the ThunderMax and AutoTune modules Due to the mounting location and space constraints on the Sportster for the ECM your ThunderMax system is supplied with a separate AutoTune module The ThunderMax ECM mounts in the same location as the factory ECM under the seat the AutoTune module must be mounted separately Step 2a Remove the seat Open the left side frame cover opposite the oil tank to expose the fuse panel Locate and remove fuse la
2. These notes are stored with the saved map remember to edit them when making changes for future reference Oxygen Sensor Care Items that can damage or shorten the life of your sensors Leaded fuel Race fuel Oil deposits from oil consumption problems Excessive moisture exposure Excessive extreme heat There is no warranty on sensors Replacement P N is 309 355 ProductSupport ZippersPerformance com 7
3. used 2 different speedometer calibrations during the extended 2003 model production Which calibration you may need is easily identified by checking the part number on the back of your factory ECM Calibration 20480 is used if the part number ends in 03 while 4352 is used if the ECM p n ends in 02 If your turn signals don t cancel on a 2003 model try the alternate setting 2007 up Big Twin models There are two settings in the Module Configuration Basic Settings page that should to be set to the following to enable the 6 gear indicator light to function Final drive ratio 87 84 for 06 07 Dyna Gear 6 Min TPS 40 Sportster models The Main Relay Loc must be set to 1 under the Basic Settings Module Configuration page or the engine will not start Accel Fuel is be used to tune throttle response go to Module Configuration Basic Settings AFR Correction vs Engine Temperature page is used to adjust cold start AFR s It is active yet should be used with extreme caution Any changes made to this page affects all maps at every throttle position every 256 RPM s See SmartLink Tuning Manual for procedures AFR vs Engine Temperature is active yet at this time you should be discouraged from making any changes to this page www lhunder Max com Installation Setup Guide V2009 04 23 Air Fuel TPS RPM These pages reflect desired targets of AFR to throttle position at every 256 RPM E
4. PB a et Check Internet For Updates 2 Select BaseMap OE I er Ae Available base maps will be shown if the Clear Filters button at the lower left of the screen is highlighted click it to clear filtered maps so all maps will be shown Dane Man De inition fe arate IE r Era The trirta 4i Harepiadon aH j Tk ML Ane ae Shock HO ML Mead Pee 415 ParleyDawideon Faina Bod MD ML 45mm Shock HE ML Heed fige BAJ Tipgesrs Zier Rock AD L Sen 21 Deel Fist Cat Hark fiche i 5 TUS Sir Dea 42 ni Trot Dual ihat Ful Sibiri he Paley iavdon i DLS Sow peas 4 22 Ini Shock MO PL head Pipe 553 arepiuidann Tiii Sm ipes 422 ini Shock H FL Hemd Pica oH Aertey Coricteon DL OS Sher Dpgers 422 Ini 2 0 Thurederheader FL Lovey Les Hark pacer O05 Shir Pipes 47 Ini 2b Diet Fak Cab 419 arlepiiidio Shock MO OLAS ibak 4 at a Shock MO PL ad Pga 4m PlateyDawiceon Sock HD OS i bri Shock H FD Head Pipe 421 AareyOorviceony Sock ADP ee E Dey Shock AC FL Heed Pape Sheek HOG RS Sherk 4 22 bel Shock HE FL Head ee Shock MO OARS Bak 4k Bal Stock MD PAD Hiid Aps Spock MO O05 Shock 4 22 Beal i i Fro Pipe Shek HOC OS Shock 4 22 be Tre Dua Aireharh Full Syse Thik HE DLE Sleek A Beg Shock HD FEST Heed Pape Stock MEP r Fi Shick HO PL ted Pee at Hartke fecha azi halebi 44 bhotkeyDerwicknon 41s adaa sei Haritik artayDiidia Partepiiider Hariepimiden Harkey iih Parkeria Piste
5. and changing this number overrides ALL Air Fuel Ratio vs TPS pages at all RPM s To target specific Air Fuel Ratio RPM ranges and throttle positions leave this box unchecked and edit the individual Air Fuel TPS RPM map pages located under the Tuning Maps tree Individual Air Fuel targets are pre set within the base map to provide a good balance between power and economy Individual cell throttle position rom AFR targets can be viewed and adjusted on these pages Use the left right arrow keys to navigate the individual blocks strike the spacebar to view the values use the up down arrow keys to adjust the values Click the Monitor button when linked live www lhunder Max com 309 365 Installation Setup Guide V2009 04 23 and a vertical bar will show the actual throttle position See the SmartLink manual for further tuning instructions Idle Air Control Override Module Check OFF This setting should not be checked on except for diagnosing a particular type of supported problem or during tuning on a load cell dyno Changing this setting will lead to starting and idling problems Maximum CLP Offset Module Session Module button sets the AFR maximum learning correction from the base map s fuel setting per session by percentage range is 0 10 A session is defined as the period of time from engine on to engine off per cycle Maximum Module button sets the total AFR maximum learning corre
6. beled ECM POWER top left fuse sticker with fuse identification is located on the inside of the frame cover www lhunder Max com 309 365 Installation Setup Guide V2009 04 23 Installation Setup Guide Please Note This product is Legal in California only for racing vehicles which may never be used upon a highway The user shall determine suitability of the product for his or her use Installation and use on a pollution controlled vehicle constitutes tampering under the U S EPA guidelines and can lead to substantial fines Review your application and check your local laws before installing Step 2b Unplug and remove the factory ECM from the motorcycle located on top of the rear fender under the seat Plug in and install the ThunderMax ECM in the same location over the locating pins shown Step 2c Install the AutoTune module Mount the AutoTune module to the frame backbone using supplied wire ties right side view below Position housing so wires exit to the left as shown below ProductSupport ZippersPerformance com 1 Step 2d Insert AutoTune power communication 4 pin plug into the bike s data port gray located at the base of the battery left side of the bike Step 2e Remove the factory oxygen sensors and install the wide band units in their place Step 2f Front sensor route wiring along frame rail double up harness if necessary position harness plug at lower front primary cover a
7. ction from the base map s fuel setting by percentage regardless of number of sessions range is 00 25 Unless your application is a considerable mismatch to the installed base map the default settings of 5 and 20 percent are sufficient for most AFR corrections You should always pick the best possible map match during the selection of your base map The theory behind this is to reduce the range and time the closed loop system needs to learn offsets corrections for the target AFR If your map selection is a poor match to the application the amount of learning needed will be significant Review the parameters of your base map vs available base maps under Base Maps Listing to ensure you have the best map match and the latest version of the map ProductSupport ZippersPerformance com 6 TIPS AND GENERAL INFORMATION Several support features are located under the Helo menu some require an internet connection A comprehensive Tuning Manual in PDF format is included on the CD for viewing and printing from your desktop When the SmartLink_program is opened it will automatically retrieve and open the last map that was open Any time you link to your motorcycle Read the map that is installed in the ThunderMax ECM by selecting File then Read Module Maps and Settings on the SmartLink toolbar This will synchronize the map file loaded into the ThunderMax ECM with the SmartLink software 2003 FLT FLHT models H D
8. e highlights active You can now edit these settings within the ive module should you want to change any of the settings from the MAP default settings Closed Loop Processing Module Check ON to enable closed loop AutoTune processing During closed loop processing the ThunderMax module processes feedback from the oxygen sensors to adjust the fuel ProductSupport ZippersPerformance com 5 volume at all points by creating learned offset points from the installed base map fuel points The static base map is dynamically used by the ThunderMax module and the AutoTune s active closed loop feedback system This system optimizes the fuel points to fit the target air fuel ratio through learned offset points These learned offset points are stored within the ThunderMax and are used in conjunction with the base map The base map fuel points are not being adjusted by either the AutoTune or ThunderMax modules If AutoTune Closed Loop Processing is un checked fuel points will be adjusted to the last learned offset points or if no learning has occurred to the original base map points Stored offset points remain within the module in the event that power is interrupted for any reason the learned offset points remain until re learned or cleared under the Map Editing toolbar menu Air Fuel Ratio Override Module A single Target AFR setting can be applied using this command Clicking this box
9. erature reaches 275 degrees After reaching temperature of 275 degrees the IAC Auto function automatically shuts off You can terminate this function at any time and re run it at a later time if you wish Step 11 Unlink the SmartLink software from the ECM turn off the ignition switch and remove the communication cable from the ThunderMax ECM Use the Save As command to create a folder and save the map to your hard drive The motorcycle is now ready to be ridden Several riding sessions that allow the engine to reach normal operating temperature should be completed During this process the IAC virtual stops will automatically be adjusted to the IAC target values set within the maps basic settings This feature automatically adjusts how the engine comes back to the specified idle speed If the IAC stops are set too low the engine will dip below the specified idle speed during certain transient conditions If the IAC stops are above www lhunder Max com 309 365 Installation Setup Guide V2009 04 23 the IAC position the engine will idle above the idle rom specified in the idle speed vs engine temperature page If it determined that these automatic adjustments have not resulted in satisfactory operation of the engine consult the SmartLink Manual available under the Help section of the toolbar Section 3 Tuning the ThunderMax ECM for further adjustment procedures CLOSED LOOP PROCESSING When equipped with AutoTu
10. g certain that the cable is routed away from any part of the motorcycle that generates heat Special Note for International Model Bikes with Active Exhaust Enabled f your bike is equipped with a working Active Exhaust Valve you must unplug the active exhaust harness before linking to the module as the AEV circuitry conflicts with the communication stream You can re connect the harness after unlinking If the stock exhaust has been changed disregard this step ThunderMax does not support active exhaust Step 6 To link to the module turn the key switch to the Ignition position making certain the RUN OFF rocker switch Kill Switch on the handlebar controls is in the RUN position Select the Link USES a eee Rey eit Button in the ols Configure window Help SmartLink software D a The button turns green to indicate a successful link Answer No to the Do you wish to READ the module map now question at this time www Thunder Max com 309 365 Installation Setup Guide V2009 04 23 From the toolbar click File Write Module Maps and Settings answer OK to the message that informs you that you are about to overwrite the current map in the module the transfer bar appears during the map load Step 7 Verify Module Settings Before performing this step clear any active Diagnostic Code readings While linked from the Tuning Tree select Module Configuration Diagnostic Codes C enso
11. n Head Temp High M Seni Sense OE Bareeneter Lene jf Seniai OF Barometer High pA oF Sensas Power High E Erriari OE Zenit Power High H Read Diageostic Wes Cien Diaqeostic Codet When the Diagnostic Codes window appears select Clear Diagnostic Codes After completing this step select Basic Settings from the Module Configuration menu and verify that the speedometer calibration is correct After verifying these settings click Write Basic Settings If the installation is to be operated in closed loop mode with AutoTune module select Configuration from the toolbar menu and click Closed Loop Configuration Verify that the Closed Loop Processing and AutoTune boxes are checked N on the left module side of the window File EFI Maps Map Editing Tools Cor F figure Monitoring Window Help Tantay ape OS ee A E IAC Curves Air Fuel Ratio Curves Ignition Timing Maps E Air Fuel TPS rpm E Module Configuration Basic Settings Warranty Informatic Diagnostic Codes Module Closed Loop Settings V Close Loop Processing Module Ratin id i IMPORTANT STEP BEFORE STARTING ProductSupport ZippersPerformance com A Step 8 Before restarting the engine from toolbar click Monitoring Show Gauges The Engine Speed Engine Head Temp IAC Position AFR Front AFR Rear and AFR Target gauges are automatically formatted and are sh
12. ne your SmartLink software will allow you to set Air Fuel tuning parameters for your ThunderMax and its installed base map To set the AutoTune Limits go to the toolbar and click Configure Close Loop MODULE Settings The Closed Loop Configuration dialog page opens the right side shows the default MAP settings stored in the MAP file settings are applied to the installed base map during the Closed Loop Format conversion performed by SmartLink while the left side shows what the module is currently set to unadjusted these settings will mirror losed Loop Configuration Module Closed Loop Settings Map File Closed Loop Settings I Close Loop Processing Module V Close Loop Processing Map iV AutoTune Module j AutoTune Map Air Fuel Ratio Override Module Air Fuel Ratio Override Map V AFR Override Enabled Module AFR Module 13 0 AFR Override Enabled Map Idle Air Control Override Map IAC Override Enabled Map ea Idle Air Control Override Module TAC Override Enabled Module Ereg Maximum CLP Offsets Map Session Map s Maximum Map 20 Max CLP Offset Module Session Module 5 Maximum Module 20 o MAP s settings The un highlighted left MODULE side of the page allows editing of those settings within the MODULE for tuning purposes while unaffecting the MAP settings To edit module settings click the Link Read Module button left sid
13. own on the screen Additional gauges can be created if desired see SmartLink Tuning Manual under Helo menu but the above gauges are most helpful during initial set up You may select any gauges that you deem important if too many are chosen your screen may appear cluttered Step 9 Select the Monitor button to active the gauges It is located beside the Link button and will turn green when the monitor gauge functions are live The gauges will be displayed if they were not already on the screen Tuning Maps Air Fuel Ratio Curves Aiv Fuel Ratio ve T DattewWetage _ Transient Fuel AC Curves 14 89 Volts 0 00 ms Front Cyl Spark Ady Injector Pht 00 deg 24 65 me Ignition Timing Maps Module Configuration Basic Settings Step 10 Now select the IAC Stops vs Engine Temperature page from IAC Curves menu within the tuning tree Strike the ail Spark Achy re Kec ers Sto We En Ine wi erature Iq p w a ii peratureh oe deg Module Configuration ite Rear Cyl Spark Adv spacebar to show the actual values of the tuning block use left right arrow keys to move the block marker Make certain that the motorcycle is in neutral and the engine is cold and then start the engine Once the engine idle is stable after 15 20 seconds select the IAC Auto button Idle Air Control Auto Adjustment Allow the IAC Auto function to run at idle until the engine head temp
14. rea Connect the sensor to the closed loop module secure with wire ties 309 365 Installation Setup Guide V2009 04 23 Step 2g Rear sensor Route wiring down the left frame rail behind the primary housing with the plug located along the frame turn Double back the wiring to the rear sensor Connect the sensor to the closed loop module secure with wire ties Oxygen Sensor Installation Notes The wide band sensors are longer than the factory sensors Installation of the wide band sensors into factory headpipes presents no clearance problems however some aftermarket pipes may require exhaust pipe modification or sensor bung relocation for interference free installation The sensors must mount freely without contacting surrounding components If this_is_not possible do not attempt _to_bend or modify the sensor in any way as it is a sensitive electronic component and will be damaged if you do Modify the pipe if required for clearance Weld in bungs are available for exhausts systems not equipped with bungs or if current bungs present clearance issues Bungs should be located no more than 3 4 from the head pipe connection for ideal location refer to the factory location on 2007 up models Weld in bungs are available from Zippers 272 200 straight 272 202 angled Chase the threads after welding with an 18 x 1 5mm tap available from auto parts stores and verify that the oxygen sensor threads in easily without
15. the map youve chosen left click blue bar indicates selected map and click Close button This brings you to the Base Map Name Encoding page from which you can review the map parameters Click the Load BaseMap button to load the map into the software Base Map Name Encoding F AAAA A Base Map File Name HRCSSSRGUGOF07 08 slk Select BaseMap Check Internet For Updates ee From this page you can load the base map into the software by clicking the Load Base Map button Close this page to view the open map page ProductSupport ZippersPerformance com 3 Step 4 From the Tuning Maps Tree click the sign next to Module Configuration then double click Basic Settings The basic settings page opens Check to see if the Speedo Cal calibration setting matches your year and model if not click the button enter the correct value as shown then click Close Bu HE ae Cres m l Rew Limit AE Max Learning Offset Decel Furl Cut Rpm High Accel Fuel Fina idie Rpm inital Pael Pilar Cranking Fuel IAC Home Position LAC Stop Target Decel Foel Cet LAC Min Learming Offert Decel Puel Cut Apm Lew cad Module Settings Write Module Settings Speedometer Calibration Settings XL 883 2007 up 48400 XL 1200 2007 up 46000 Step 5 Now you are ready to Link and Write the map to the ECM Attach the communication cable from your computer to the ThunderMax module makin
16. the pipe wall interfering with the sensor tip After installation route the sensor harness away from the engine and along the frame when possible above the lowest frame point to avoid the possibility of dragging ground during operation Avoid routing harnesses where engine movement or moving parts can contact and damage the harnesses or connector plugs The AutoTune harness for the rear cylinder sensor is shorter and can be easily identified by black tracers on all of its wires both plugs are clearly marked for front and rear use It is very important to install these correctly or the engine will perform poorly Tie the harnesses to the frame or existing component harnesses taking care to avoid contact with any vibrating component that may chaff the sheathing or wires Some disassembly of bike components may be required for best harness routing ProductSupport ZippersPerformance com 2 Step 3 Load a Base Map to your SmartLink software Selecting a base map for your ThunderMax is easy thanks to the filtering system in the SmartLink software Open SmartLink from the toolbar choose EFI Maps EFI Map Listings Definitions You should first update the Map Definitions file to ensure you have the latest available maps Close the Base Map Definitions window then click the Check Internet For Updates button requires internet connection follow prompts After updating select Select BaseMap SMLIV Zippers End User SFW 010 ZI
17. xample if you desire a leaner mixture for added fuel economy then you can easily make multi tiered AFR targets at specific throttle positions and RPM s that will be learned during closed loop processing During warm up the AFR on both cylinders will be richer than the target AFR at normal operating temperatures this is a normal part of the warm up map AutoTune and its targets are inactive below 200 degrees Target air fuel ratios can be viewed on the Air Fuel TPS RPM pages When these pages are open you can view the target AFR by clicking on a dot and tapping the space bar to view the target at a specific throttle position for that RPM Use arrow keys to raise lower targets Writing new_or modified maps to the module requires the system to be re initialized Step 7 and any existing learned fuel and IAC adjustments to be cleared Map Editing clear Linking and editing an existing map within the module does not require above steps System Updates are available through SmartLink with an internet connection Software Firmware and Map updates can be downloaded check frequently for updates In Tank Fuel Filters should be inspected as a part of routine maintenance The filter is small and one bad load of fuel can clog it The factory recommended service interval is 25K miles Save your edited maps to your hard drive using the Save As command Document the changes in Map Notes located under EFI Maps on the toolbar
18. yDawiceon PERESPPR PR REPS E FF Stock HO Obi Shock 4 Sheek ADO A Shock 4 i Thik HE Gi fF Skee haz i Shock MO GLARE ame Stock HO Ob Shock 4 True Copel Aishat Pull Sytem 21 Denil Fat Cot Shock HD FST Howe Pape Rii Thundarhaader Steg Duss wih Deg Shook PE Filter the maps to locate a base map that best matches your application by placing your curser first over any Engine Type that matches your engine and right click it All maps that do not match your selection will be filtered from the screen Base Map Definitions _Engine Type 46 Harley David 415 Harley Davidson 120 cc 543 Zippers 1200cc www lhunder Max com 309 365 Installation Setup Guide V2009 04 23 Second place your curser over the Throttle column and right click your match Definitions EngineType A Throttle Stock HD 8L 45mm Stock HD XL 45mm Stock HD L 45mm HarleyDavidson agace Harley Davidson 1200cc Zippers 1200cc Third right click the Exhaust type that closest matches your application EN r Throttle Exhaust Stock HD XL Head Pipe Stock HD XL Head Pipe Stock HD XL 45mm Stock HD XL 45mm Stock HD XL 45mm Fourth right click the Muffler column if further definition of the exhaust system is required depends on exhaust application Keep right clicking the application columns until you have located the best map match in the case of identical maps choose the latest date Highlight
Download Pdf Manuals
Related Search
Related Contents
Du 1er au 15 mars - Commune de Plougonvelin Integrated Display Industrial Computers with Keypad User Manual 送風機仕様書(PDF) SoftWall Finishing Systems SW6423352049 Instructions / Assembly 取扱説明書 - バンダイ scope - REDUCE Computer Algebra System EVault User Guide for Windows Agent Samsung 932BF Lietotāja rokasgrāmata Copyright © All rights reserved.
Failed to retrieve file