Zebra Technologies TTP 2100 Photo Scanner User Manual
Contents
1. i 10 mm Additional space is required for paper loading and paper jam removal Consider mounting the printer on a movable platform so that the printer can be maintained outside the printer enclosure Note We recommend you to make the output slot 97 mm wide This way you will be able to use all paper widths that the TTP 2100 series of printers can handle 11 04 2009 TTP 2100 Operator Guide P1021708 001 Installation Installation Considerations 22 Caution NEVER use screws that go into the printer more than 4 mm This will destroy the electronics inside Electrostatic Discharges and Earth Currents Preventing ESD and earth currents from affecting the printer operation requires proper connection of the printer chassis to protective earth through a mounting platform or through a separate earth conductor A threaded hole for an M4 earth screw is provided on the back of the printer Use an M4 x 10 screw and two lock washers when fastening the ground cable Figure 8 Location of Earth Grounding Screw Earth Screw Note An optional antistatic brush can be fitted to the front of the printer if required Ambient Light There is an optical sensor at the paper exit at the front of the printer To ensure proper printer operation design the kiosk so that it prevents direct sunlight or light from indoor lamps from reaching the sensor through the paper exit P1021708 001 TTP 2100 Operator Guide 11 04 2009 Ins2. nee 30 4 OperallOl 2k cauaa kar RAE ARR Ra qaa AG E ARR AR aai 31 Loading Fanfold Ticket Stock 20 0 cece eee 31 Installing a Paper Roll tetas 32 Clearing Paper Jams rr 34 P1021708 001 TTP 2100 Operator Guide 11 04 2009 Introduction About this Manual This manual will be updated as from time to time printer functions and features may be added or amended You will always find the latest edition on our web site http www zebra com If you require functions not found in this manual edition please contact Technical Support for your region or the Zebra partner the printer was purchased from 11 04 2009 TTP 2100 Operator Guide P1021708 001 About This Document Contacts Contacts Technical Support via the Internet is available 24 hours per day 365 days per year Web Site www zebra com E mail Back Technical Library E mail address emb zebra com Subject line Emaillist Self Service Knowledge Base www zebra com knowledgebase Online Case Registration www zebra com techrequest Which Department Do You Need Regional Headquarters The Americas Zebra Technologies Corporation 475 Half Day Road Suite 500 Lincolnshire IL 60069 USA T 1 847 634 6700 Toll free 1 866 230 9494 F 1 847 913 8766 Europe Middle East and Africa Zebra Technologies Europe Limited Dukes Meadow Millboard Road Bourne End Buckinghamshire SL8 5XF United Kingdom T 44 0 1628 556000
3. Zebra TTP 2100 Kiosk Ticket Printer Operator Guide a P1021708 001 2009 ZIH Corp The copyrights in this manual and the software and or firmware in the printer described therein are owned by ZIH Corp and Zebra s licensors Unauthorized reproduction of this manual or the software and or firmware in the printer may result in imprisonment of up to one year and fines of up to 10 000 17 U S C 506 Copyright violators may be subject to civil liability This product may contain ZPL ZPL II9 and ZebraLink programs Element Energy Equalizer Circuit p3 and Monotype Imaging fonts Software ZIH Corp All rights reserved worldwide ZebraLink Element Energy Equalizer E and all product names and numbers are trademarks and Zebra the Zebra head graphic ZPL and ZPL II are registered trademarks of ZIH Corp All rights reserved worldwide All other brand names product names or trademarks belong to their respective holders For additional trademark information please see Trademarks on the product CD Proprietary Statement This manual contains proprietary information of Zebra Technologies Corporation and its subsidiaries Zebra Technologies It is intended solely for the information and use of parties operating and maintaining the equipment described herein Such proprietary information may not be used reproduced or disclosed to any other parties for any other purpose without the express written permission of
4. D D o N O A Jg C o e e Jg C o Female 9 Ril 9 Ree e RI 9 Female Serial Cable 10825 000 Dotted leads are not connected in the printer To be able to connect the cable in any direction make symmetrical cables P1021708 001 TTP 2100 Operator Guide 11 04 2009 Installation 25 Connecting to the Computer TTP 2130 Connect the printer to the USB port of the computer or the USB hub to be used USB connectors can be recognized by the following symbol diu The connector on the printer is a 4 pin USB type B connector See Table 4 USB Connector J13 Pin Assignment on page 105 for pin assignment A suitable cable is available from Zebra part number 105850 028 Figure 13 USB Cable with Type A and Type B Connectors pagi L 00 3 6 5 po f eS y H POSITION ui POSITION 1 SW98041 11 04 2009 TTP 2100 Operator Guide P1021708 001 26 Installation Connecting the Power Connecting the Power Caution Using a non Zebra power supply may cause excessive EMC interferences and void the EMC certifications of the printer Caution To avoid electrical shock and printer damage wiring of a non Zebra power supply should only be done by qualified service personnel Use ONLY a power supply which meets the following minimum requirements 24 VDC 45 e 70W average 2 92A and 284W peak 11 8A power supply Figure 14 Location of Power Connec
5. Zebra Technologies Corporation Product Improvements Continuous improvement of products is a policy of Zebra Technologies Corporation All specifications and designs are subject to change without notice Liability Disclaimer Zebra Technologies Corporation takes steps to ensure that its published Engineering specifications and manuals are correct however errors do occur Zebra Technologies Corporation reserves the right to correct any such errors and disclaims liability resulting therefrom Limitation of Liability In no event shall Zebra Technologies Corporation or anyone else involved in the creation production or delivery of the accompanying product including hardware and software be liable for any damages whatsoever including without limitation consequential damages including loss of business profits business interruption or loss of business information arising out of the use of the results of use of or inability to use such product even if Zebra Technologies Corporation has been advised of the possibility of such damages Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you Contents Je ie NG PAA AA AA 5 About this Manual 0000 eee 5 Contact s xz d hae RE AA APA 6 2 Product Presentation qua oaed d X Ea ga den WARREN RON QU a OOS 7 Presentet x ua ad ee epe Ai ie ahead do E E e Reh a E SE oUm ees ce eee 10 Ej
6. any angle Horizontal is the most common use but vertical with the ticket presenting upwards can be used if you want the ticket to come up from the desk surface Vertical with the ticket presented downwards can be used if you want to stack many tickets before picking them up Figure 5 Printer Installation Orientation Options TTP 2100 Operator Guide P1021708 001 20 Installation Installation Considerations Quick Fit Hubs The printers attach to the kiosk in two ways using two screws using slides with leaf spring retainers and the quick fit hubs Figure 6 Front Bottom View Ticket exit Push down Cp g Quick fit hubs Keyholes a spring ws s fit hubs gt a Push Forward Fixed P1021708 001 TTP 2100 Operator Guide 11 04 2009 Installation 21 Installation Considerations Design Your Own Mounting The illustration below gives an example of a printer mounting shelf See Dimensions on page 120 and the 3D solid models and outline drawings for CAD that are available on http www zebra com Figure 7 Example of a Simple Shelf for Fastening a Standard Printer Using Quick Fit Hubs and a Leaf Spring Retainer Order No 01473 000 Leaf spring 01473 000 Inner corner of bend 10 mm 8mm 44 mm dd material for corner radius BH Center Min 100 mm per widt 10 mm Pa
7. 9 Product Presentation 11 Controls Controls Figure 3 Rear View Cover lock C du Mi BEA A NE c l Paper low Connector Power Interface Connector Status Indicator Earth Connector Screw The buttons and indicators are duplicated on both sides of the printer so that they are easily accessible regardless of how the printer is installed Feed Button The Blue Feed button has several functions Press and release will feed cut and present a complete page Any data in the print buffer will be printed If the buffer is empty the page will be blank In black mark mode the page will be synchronized with the black mark Press and hold Feed while turning on the power will print a self test printout See Making a Self Test Printout on page 28 Ifthe printer has firmware version 3 83 or higher press and hold the Feed button for 3 seconds to print a self test printout With no paper in the printer hold the Feed button pressed while closing the printhead to enter TOF mark calibration mode see Print Setup on page 86 11 04 2009 TTP 2100 Operator Guide P1021708 001 12 Product Presentation Controls Power Indicator e When the green power indicator is illuminated a 24V supply is connected to the printer Status Indicator The status indicator has several functions ON constantly the printer is operational Flash flash pause flash flash is the warning code for pape
8. E Eurtraining zebra com E China tschina zebra com courses E ttamerica zebra com All other areas tsasiapacific zebra com Inquiry Department T 1 877 ASK ZEBRA 275 9327 T 44 0 1628 556037 E China GCmarketing zebra com For product literature and E inquiry4 zebra com F 44 0 1628 556005 All other areas distributor and dealer E mseurope zebra com APACChannelmarketing zebra com information Customer Service T 1 877 ASK ZEBRA 275 9327 T 44 0 1628 556032 T 65 6858 0722 Department US E clientcare zebra com F 44 0 1628 556001 F 65 6885 0836 Internal Sales Department E cseurope zebra com E China order csr zebra com UK All other areas For printers parts media and ribbon please call your distributor or contact us Key T Telephone F Facsimile E E mail P1021708 001 TTP 2100 Operator Guide csasiapacific zebra com 11 04 2009 11 04 2009 2 Product Presentation The TTP 2100 series of ticket printers are available both for kiosk integration and desktop use They print on most ticket media from 50 mm to 82 5 mm wide using direct thermal printing The ticket media can be up to 0 25 mm thick fanfold roll or single cut handfed The printers have integrated guillotine cutter straight presenter and control board The print speed is up to 150 mm per second and the eject speed 300 mm s to ensure high throughput The cut can be synchronized with Gaps betwee
9. F 44 0 1628 556001 Asia Pacific and India Zebra Technologies Asia Pacific Pte Ltd 120 Robinson Road 06 01 Parakou Building Singapore 068913 T 65 6858 0722 F 65 6885 0838 Technical Support For questions on the operation of Zebra equipment and software please call your distributor For additional assistance contact us Please have your model and serial numbers available T 1 877 ASK ZEBRA 275 9327 F 1 847 913 2578 Hardware ts1 zebra com Software ts3 zebra com Kiosk printers T 1 866 322 5202 E kiosksupport zebra com T 44 0 1628 556039 F 44 0 1628 556003 E Tseurope zebra com T 65 6858 0722 F 65 6885 0838 E China tschina zebra com All other areas tsasiapacific zebra com Repair Service Department For back to base service and repair T 1 877 ASK ZEBRA 275 9327 F 1 847 821 1797 E repair zebra com To request a repair in the U S go to www zebra com repair T 44 0 1772 693069 F 44 0 1772 693046 New requests ukrma zebra com Status updates repairupdate zebra com T 65 6858 0722 F 65 6885 0838 E China tschina zebra com All other areas tsasiapacific zebra com Technical Training T 1 847 793 6868 T 44 0 1628 556000 T 65 6858 0722 Department T 1 847 793 6864 F 44 0 1628 556001 F 65 6885 0838 For Zebra product training F 1 847 913 2578
10. ROM 12 Wait for the printer to buzz as a confirmation that the new value is stored 11 04 2009 TTP 2100 Operator Guide P1021708 001 kai Installation Top of Form TOF Sensor Top of Form TOF Sensor The TTP 2100 has a flexible top of form detection system When delivered the printer is configured with fork transmissive sensor to detect holes gaps between tickets The holes gaps should be in the paper center 12 5 mm to the right of the center according to IATA resolution 740 or at the edge of 82 5 mm wide tickets Boarding cards If the TOF mark is at a suitable position an auto calibration routine will configure everything for you You can move the sensor to other positions force the printer to use a specific sensor switch to reflex black mark sensor for black mark detection by setting up the parameters in the printer Selecting Fork Transmissive or Reflex Black Mark TOF Sensor The TTP 2100 can use a fork transmissive sensor that looks for holes between tickets or a reflex black mark sensor that looks for black marks on the back of the ticket stock Sensor mode is selected with parameter n61 see Summary of Parameter Settings on page 83 Positioning the TOF Sensor P1021708 001 The sensor board containing the lower media sensor sits on a bracket that can slide left and right in a groove This bracket is located below the ticket entry The IR light source upper media sensor sits on a similar bracket abov
11. e as No 0 See also Logotypes on page 78 Figure 17 Logotype No 0 is Printed on the Self Test Printout TTP 2130 Kiosk Printer n Logotype No 0 TTP 2100 Operator Guide P1021708 001 30 Installation Installing a Printer Driver Installing a Printer Driver A printer driver for Microsoft Windows is available on the Zebra web site http www zebra com Please follow the installation instructions that accompany the drivers and refer to the Kiosk Driver Reference Guide Part Number P1006873 001 available on www zebra com for detailed driver information P1021708 001 TTP 2100 Operator Guide 11 04 2009 4 Operation Loading Fanfold Ticket Stock 1 Turn the tickets so that the surface to be printed temperature sensitive side faces upwards Put the first ticket on the input guide and slide it up the guide into the printer 2 The printer will feed the paper locate the edge and reverse to printing position 3 When ready the yellow status led will be ON indicating that the printer is ready to be used should face down The printer will automatically load the tickets when the sensors detect a ticket is loaded Note Remember that the thermal coating should be upwards and black marks if used Figure 18 Loading Ticket Stock 11 04 2009 TTP 2100 Operator Guide P1021708 001 32 Operation Installing a Paper Roll Installing a Paper Roll 1 Turn the new pape
12. e the ticket entry When delivered the bracket is positioned to the far right In this position Sensor 1 is at the right side ready to detect the corner radius of Boarding cards Sensor 2 is at the center of the page and Sensor 4 is 12 5 mm to the right of the center at the position determined for baggage tags in IATA resolution 740 To configure the printer for other papers that do not fall into any of the three categories complete the following steps 1 Loosen the screw holding the sensor 1 72 turns 2 Press the screw in with the screwdriver and carefully slide it to the new position making sure the cables to the sensor do not obstruct the movement 3 Tighten the screw 4 Move the IR light source upper media sensor to the same position directly above the sensor Note The standard ticket guides have holes for the following sensor positions Center Edge and 12 5 mm from center and the sensor position must correspond to these holes Upper sensor Lower sensor adjuster TTP 2100 Operator Guide 11 04 2009 Installation 17 Top of Form TOF Sensor Calibrating the TOF Sensor 11 04 2009 1 2 Open the printhead Remove ticket stock Press and hold the Feed button and then close the printhead keeping the button pressed all the time Release the button The Status LED should be off Load ticket stock slide it into the paper guide and let the printer auto load the paper Note To ensu
13. ect MODE Aa done eR Rent eee MAGAN a ek Be Daa M actos aed etre b d 10 Hold MOJE uua d bee rere LE Une DEEE RR DE P ES taeda 10 nhu ie PX 11 Feed Button i52 1S GA obli E led d REIG beau BAL eee ei caue E EE 11 Power Indicator iue ake ter NA KULANG ie na Rin NER AURI dd eae 12 StatusIndiCator uu venom RE Phe NA eed bee RARE UR RUE 12 3 e Installation 42x o mACRCACACRON ECCE ACRCACAR raona RORCACN EON C RC DCN RC ae ee 13 Installing a Paper Guide aaaea a 13 Top of Form TOF Sensor budeto es 16 Selecting Fork Transmissive or Reflex Black Mark TOF Sensor 16 Positioning the TOF Sensor 0 0 cece eee eee 16 Calibrating the TOF Sensor iis 17 Installation Considerations 0 000 cece 18 OMEMTATION siaaa uen dee eon anew PAA 19 Quick Fit Hubs 2 0 20 0 0 eer 20 Design Your Own Mounting ssseseee RI 21 Electrostatic Discharges and Earth Currents 0 000 ce eee eee eee 22 Ambient light nue kk RR bad eda d ure ere E 22 Installing a Paper low Sensor Optional 0 0 cece eee 23 Connecting to the Computer 0 cette eee 24 TER AANO NG nG NABA eerie aster GL bree 24 IN uno 25 11 04 2009 TTP 2100 Operator Guide P1021708 001 4 Contents Connecting the Power 0 cece teens 26 Making a Self Test Printout 0 2 2 ct eae 28 Customizing the Self Test Printout liliis 29 Installing a Printer Driver
14. ength Sensor Mode P Parameter Settings Value List Binary Value y nm Byte Value o Resulting Value 0 Set to Default Parameter Description Sets the width of the paper loaded a into the printer This can also be used to get left and right margins for instance if you load 80 paper but set the paper width to 60 mm you get a 10 mm margin on both sides of the page Use a value of 0 for auto detection of paper width zi UboadOne Upload Retrieve Dne Retrieve All Store Values to Flash PROM Insert ne Insert All xl Print Self Test Close Ready P1021708 001 7 Select Parameter 48 paper width and enter the value in millimeters of the desired print width Paper Width Setting 82 5 mm n48 80 80 mm n48 72 76 mm n48 70 60 mm n48 54 54 mm n48 50 51 mm n48 46 8 Select Upload One TTP 2100 Operator Guide 11 04 2009 Installation 15 Installing a Paper Guide 9 Select Parameter 63 BM Sensor and enter the desired value Recommended values are Value When Used Auto selects 1 or 4 based on width of media loaded edge sensor for ATB tickets without hole in the perforation center sensor for ISO tickets most other ticket types and adhesive labels 17 5 mm from center sensor BR WwW NHN o 12 5 mm from center sensor for baggage tags according to IATA 740 10 Select Upload One 11 Select Store Values to Flash P
15. ever toward the rear of the printer b Lift the lid Figure 22 Opening the Lid 2 Remove all jammed paper make sure the paper path is clear and close the lid Figure 23 Remove Paper Trash P1021708 001 TTP 2100 Operator Guide 11 04 2009 Zebra Technologies Corporation Zebra Technologies Corporation 475 Half Day Road Suite 500 Lincolnshire IL 60069 USA T 1 847 634 6700 Toll free 1 866 230 9494 F 1 847 913 8766 Zebra Technologies Europe Limited Dukes Meadow Millboard Road Bourne End Buckinghamshire SL8 5XF UK T 44 0 1628 556000 F 44 0 1628 556001 Zebra Technologies Asia Pacific LLC 120 Robinson Road 06 01 Parakou Building Singapore 068913 T 65 6858 0722 F 65 6885 0838 http www zebra com 2009 ZIH Corp P1021708 001
16. formation specific to the printer including Firmware version Control board PCA revision Paper width Serial number Installed fonts and logotypes Parameter settings Barcode support To make a Self Test Printout 1 Enter Self Test Mode using one of the following methods P1021708 001 If the printer has firmware version 3 83 or higher Then Press and hold the Feed button for 3 seconds the printer has firmware lower than version 3 83 Press and hold the Feed button just after closing the print head See Figure 16 Press and hold the Feed button 1 while turning on the power 2 to the printer Hold down the Feed button until printing starts Each successive time the Feed button is pressed will produce an additional Self Test printout until Self Test Mode is exited Exit Self Test Mode by power cycling the printer turning the power off then on again If the power switch is not easily accessible open and close the print head Figure 16 Locate the Feed Button and On Off Switch Q vy AGO r TTP 2100 Operator Guide 11 04 2009 Installation 29 Making a Self Test Printout Customizing the Self Test Printout 11 04 2009 The self test printout starts with a text line and then a Zebra logotype This logotype is just a printout of logotype No 0 so if you want to personalize the self test printouts in your installation delete all logotypes and store your own logotyp
17. n tickets or punched holes Black marks on the non thermal side of the ticket stock Foil opacity for labels on opaque foil backing Ticket corner radius Label gaps for adhesive labels on backing liner TTP 2100 Operator Guide P1021708 001 8 Product Presentation P1021708 001 You can also print fixed or variable length tickets without synchronization The presenter can be set to eject the ticket into a tray or hold it by the back edge until the customer takes it The top can easily be opened to give the operator access to the paper path and printhead for maintenance purposes Figure 1 Principle of Operation faq 9 Control panel on both sides Cutter Tickets fall into tray Ticket sensor taken fallen Straight presenter Ticket load sensor Printhead Upper media sensor IR light source adjustable sideways Top release lever Paper entry Lower media sensor IR light receiver adjustable sideways Control board ol woo S w N TTP 2100 Operator Guide 11 04 2009 11 04 2009 Product Presentation The upper media sensor is an IR light source that illuminates the media The lower media sensor is an IR light receiver These sensors must work together to sense media gaps or out of media conditions The printer is available with two different control boards the TTP 2110 with serial interface and the TTP 2130 with USB interface A
18. printer driver for Microsoft Windows is available and the TTP 2130 interface is compatible with the Plug and Play standard The KPL control command language makes it easy to print directly from the ticket software without using a driver This is especially useful for the serial interface version with its limited data transfer rate TTP 2100 Operator Guide P1021708 001 9 10 Product Presentation Presenter Presenter The TTP 2100 does not loop the media The presenter carries the media through the printer for presentation to the user Eject Mode The ticket is ejected after being cut The printer is designed so that the ticket always drops down A sensor is located at the exit of the presenter to ensure that the printer can verify that the ticket drops down To enable this functionality set Clear presenter after print in the driver printing preferences or enable the appropriate parameter setting if using direct print commands Hold Mode When presented only the very end of the printout is held by the printer so the customer can easily take the printout no matter how long or short it is If a customer is printing more than one ticket the printer can detect when the first is taken and automatically print the next and hold that ticket until taken continuing this process until all tickets have been printed Figure 2 The Presenter Print and drop bo JA S Print and take P1021708 001 TTP 2100 Operator Guide 11 04 200
19. r low The warning code is reset automatically when the condition causing it is removed This behavior is disabled by default but can be enabled by setting parameter 52 Warning Level to 1 Flashes rapidly indicates error Hold down the Feed button and the number of flashes will reflect the status code Table 1 Status Indicator Flash Codes Number at Description Flashes 1 Presenter jam paper cannot be ejected 2 Cutter cannot return to home position 3 Out of paper 4 Printhead lifted 5 Paper did not reach presenter sensor in time 6 Temp error printhead is above 60 C 7 Paper jam during present 10 TOF mark not found on media load 11 TOF mark calibration error Fast flashes Checksum error at firmware loading Steady light Wrong firmware type Constantly off Waiting for paper in TOF mark calibration mode Status codes are reset When the conditions causing them are removed When the printer is power cycled turned off and then on For all paper jam conditions after the jam is cleared lifting and lowering the printhead P1021708 001 TTP 2100 Operator Guide 11 04 2009 Installation Installing a Paper Guide The TTP 2100 printers are delivered without paper guide fitted 1 Open the printhead by pushing the green printhead open lever backwards and lifting up the printhead See Clearing Paper Jams on page 34 2 Insert the T shaped tabs of the paper guide into the T holes and press
20. r roll as shown The paper should be inserted into the printer with the temperature sensitive side up so that the paper leaves the roll from the top Figure 19 Installing a Paper Roll Tem perature sensitive coating SW96074C 2 Tear off a full turn of the paper from the new paper roll Caution This is important since the outer end of the paper is usually fixed to the roll with some type of glue or self adhesive substance that might otherwise cause paper jam or even printhead damage Figure 20 Remove Outer Layer of Paper Roll Glue or similar substance SW96075C 3 Make sure the printer is turned ON 4 Insert the ticket stock through the paper entry opening at the back of the printer s Note The ticket sensor is at the center of the print width If the ticket edge is torn off in such away that the sensor does not see it auto load will not be triggered If so reshape the edge so that the sensor sees the ticket stock P1021708 001 TTP 2100 Operator Guide 11 04 2009 11 04 2009 Operation 33 Installing a Paper Roll 5 Press the Feed button so that the printer feeds cuts and ejects a page This ensures that the first ticket printed will have a straight edge Figure 21 Example of Bad Page Edges TTP 2100 Operator Guide P1021708 001 34 Operation Clearing Paper Jams Clearing Paper Jams Should a paper jam occur follow the procedure below 1 Open the printer lid a Press the green release l
21. re good calibration conditions lightly press the ticket stock towards the bottom of the input guide during calibration The printer will forward the paper until it finds two TOF marks and then stop and save all TOF mark parameters Open the printhead and remove the ticket stock Close the printhead and feed the tickets in through the paper guide again The printer is ready for use Repeat this procedure if the calibration fails or if the printer is used with tickets that differ from the original specification Note If you use the Dual guide 01990 400 on your printer you must calibrate twice once in the wide paper path and once in the narrow The printer will choose the appropriate set of parameters based on which paper path contains ticket stock TTP 2100 Operator Guide P1021708 001 18 Installation Installation Considerations Installation Considerations The TTP 2100 Kiosk is for embedded applications and should be installed in an enclosure such as a self service kiosk Caution NEVER use screws that go into the printer more than 4 mm Longer screws will destroy the electronics inside The TTP 2100 Desktop is a stand alone printer in a housing The housings can be stacked so two or more printers can reside on top of each other to save space Thy P1021708 001 TTP 2100 Operator Guide 11 04 2009 Installation 19 Installation Considerations Orientation 11 04 2009 The TTP 2100 can be installed at
22. talling a Paper low Sensor Optional Installation 23 Installing a Paper low Sensor Optional A paper low sensor alerts the system that the media stock level is running low The paper low sensor works with paper rolls and fanfold media The purpose of this sensor is to get an early alert so that you can replace the ticket stock in time in remotely located kiosks Roll holders supplied by Zebra can be equipped with paper low sensors Attach the sensor and connect the cable to the paper low connector at the back of the printer Figure 9 Paper low Sensor Connection Paper roll Paper low J10 sensor Roll holder shaft 3 2 1 5 Gray Connection inside printer PL SENSE 5 200 ohm SW97081F 11 04 2009 TTP 2100 Operator Guide Paper low Connector P1021708 001 24 Installation Connecting to the Computer Connecting to the Computer Figure 11 Location of Interface Connector Interface Connector TTP 2110 Connect a Zebra serial cable ordering No 10825 000 between the printer and the computer to be used We strongly recommend using the Zebra cable because many incompatible cables are available which may cause communication problems Figure 12 Serial Interface Cable 10825 000 w N 4 7 x x o O 2j m x x o O w N o N O A 090 no AM e i OU O ng
23. the rear of the guide down and in 3 Fasten the nut using the 5 mm wrench supplied 4 Close the printhead Figure 4 Fitting the Paper Guide Prim ary input guide O 0 Screw When a guide is fitted make an auto calibration with the ticket media that you are going to use in the printer Most ticket medias auto calibrate perfectly and the printer is ready to use Should auto calibration fail on your media set up paper width parameter n48 and sensor selected parameter n63 to reflect your media Then redo the auto calibration 5 Start the utility program Zebra Toolbox This application is available from http www zebra com 6 Select Tools Parameter Settings 11 04 2009 TTP 2100 Operator Guide P1021708 001 14 Installation Installing a Paper Guide File Tab Stop Number 8 Tab Stop Number 9 Tab Stop Number 10 Tab Stop Number 11 Tab Stop Number 12 Tab Stop Number 13 Tab Stop Number 14 Tab Stop Number 15 Tab Stop Number 16 Presenter Speed CR LF Behavior Auto Cut After FF BM Mode Document Mode Page Length High Byte Page Length Low Byte Black Mark Length Minimum Black Mark Length Black Mark Cut Offset High Byte Black Mark Cut Offset Low Byte Top Margin High Byte Top Margin Low Byte Black Mark Sensor Calibration Wall Compensation Advance Before Cut Black Mark Sensitivity Warning Level Lock Parameters Max Status Code System USB Vendor Class Partial Cut L
24. tor Power Connector Caution On power supplies with line voltage selector make sure it is set to your local line voltage Using the appropriate Zebra power supply for TTP 2100 Desktop or Embedded 70W Power Supply on page 122 1 Connect the cable from the power supply the power connector on the back of the printer 2 Connect the power cable to the line outlet 3 Turn ON the power P1021708 001 TTP 2100 Operator Guide 11 04 2009 11 04 2009 Installation 27 Connecting the Power In kiosk applications you may draw power from a common PSU in the kiosk if the characteristics are suitable In such a case cables that fit the connector on the back of the TTP 2100 are available from Zebra If you make cables of your own connect the voltages according to the following illustration Note Protective ground and minus output should not be interconnected in the power supply At the printer end of the cable use a Tyco Mate N Lok connector housing and two contact sockets Figure 15 Power Connection Housing Socket Tyco No 350777 1 Tyco No 350689 1 Table 2 Current Consumption Mode 58 60 mm paper width 80 82 5 mmpaper width Idle 150 mA 150 mA Standard text printing 0 7 A average 1 A average All black printing 4A 6A TTP 2100 Operator Guide P1021708 001 28 Installation Making a Self Test Printout Making a Self Test Printout A Self Test Printout provides a printout showing in
Download Pdf Manuals
Related Search