Xantech ISM4 Home Theater System User Manual
Contents
1. Step 7 The selected source LED will blink the number of times for the IR command that it is presently on Teach Command SOURCE 1 OFF Macro To enter SOURCE 1 OFF Macro press and hold the NEXT button until the SOURCE 1 LED blinks once and release SOURCE 1 LED will turn ON solid green and PROGRAM LED will turn ON solid orange Repeat Steps 2 7 Adding Delays 9 To add a DELAY after the IR Command following Step 5 press the DELAY button The PROGRAM LED will flash once to indicate that the ISM4 has entered delay mode 10 Press the NEXT button once for each second of delay to be added to the IR Macro Command Press the PREV button once for each second of delay to be subtracted To save the Delays press and release the SEQUENCE button NOTE The first press of the NEXT button will add one second of delay Each additional press will add one second up to 60 seconds after which the timer will reset back to 0 seconds The first press of the PREV Button will add 60 seconds of delay Each additional press will subtract one second down to 0 seconds after which the timer will reset to 60 seconds Test Macro 11 A fully programmed Source ON or OFF Macro can be tested by pressing the TEST button while in EDIT mode NOTE 1 If the IR Commands and Delays within the IR Macro Commands were not properly saved the Macro cannot be tested and the Program LED will flash red to indicate error NOTE 2 To Test a Macro starting from Normal Operation M2. TEMENT Effective for products sold after October 1 2006 Xantech Corporation Xantech warrants to the holder of a valid proof of purchase as the first end user purchaser You its products to be free from defects in materials and workmanship as defined herein for the periods specified below from the date of purchase This limited warranty extends only to You for product purchased and used in the United States of America For product purchased outside of the United States of America the terms of this warranty apply EXCEPT that You must contact the Xantech Authorized Distributor in your region for warranty services Product is not intended for end user installation If within the applicable warranty period above You discover such item was not as warranted above and You promptly notify Xantech in writing Xantech shall repair or replace the items at its option Xantech may elect which remedy or combination of remedies to provide in its sole discretion Xantech may use functionally equivalent reconditioned refurbished pre owned or new products or parts under this limited warranty This warranty shall not apply a to product which shall have been installed by other than an authorized Xantech installer b to installed product which is not installed to Xantech s specifications c to product which shall have been repaired or altered by others than Xantech d to charges for installation or set up or adjustment of customer controls e to produc
3. TYPICAL SYSTEM CONNECTIONS ISM4 INTELLIGENT SYSTEM MANAGER PROGRAMMING QUICK START GUIDE Front TEST IRLEARN SOURCE1 SOURCE2 SOURCE3 SOURCE4 PROGRAM DELETE SEQUENCE DELAY This ISM4 Programming Quick Start Guide provides the basic instruction to programming an ISM4 To use the Quick Start Guide fill out the Macro Programming Table and follow the Programming Instructions For complete instructions on installation connections and additional programming capabilities refer to the ISM4 Installation amp Programming Manual The System shown on the back cover illustrates a typical Home Theater System In the configuration as shown when the TV is turned ON the ISM4 will sense the TV ON state look at Sources 2 4 A V Receiver Cable Box and DVD Player and if any of them are OFF automatically output the Source ON Macros for those devices to turn them ON If at any time while the TV is ON any of Sources 2 4 turns OFF the ISM4 will automatically turn it back ON When the TV is turned OFF the ISM4 will sense the TV OFF state look at Sources 2 4 and if any of them are ON automatically output the Source OFF Macros for those devices to turn them OFF There are endless applications for this type of power management Two other system examples are shown in the ISM4 Installation amp Programming Manual for reference See Section System Applications 291 Series or Dash 30 Series IR Receiver Programmable Remote 781ERGPS 12VDC Powe
4. cro Press and release the SEQUENCE button again to enter IR Learn Mode for SOURCE 1 ON Macro The Source 1 LED will flash for about 5 seconds This is the amount of time allowed to teach an IR Command Position the remote control for the System Reference Device Source 1 directly in front of the IR Learn window on the ISM4 1 4 inches depending on the remote and press and hold the ON or Power button on the remote control until the PROGRAM LED flashes green three times If the PROGRAM LED flashes red three times the IR command was not learned return to Step 2 Test Command Press the TEST button and confirm the function of the learned command on the SOURCE 1 device Save Command If the SOURCE 1 device responded properly to the learned command press and release the SEQUENCE button again to save the command The PROGRAM LED will flash once The ISM4 will automatically return to Edit Mode upon save To return to Edit Mode without saving press the PREV Button Repeat Steps 3 5 as necessary until the command is learned tested confirmed and saved Note 1 If a delay is required proceed to Step 9 7 If there is no delay required for IR Macro Command 1 and there is at least one more IR Command in the Macro press and release the NEXT button SOURCE 1 LED will flash twice indicating the ISM4 is ready to learn the IR Command for IR Macro Command 2 Repeat Steps 2 5 to add the IR Command Note 2 To add IR commands 3 5 repeat the sequence
5. ing Be sure that all Sensors are connected to the appropriate device and the Source Sense Input Ports on the ISM4 Also be sure all IR Emitters are connected to the appropriate Source IR Out Ports on the ISM4 and attached to the correct device over the IR eye for that device 15 With all Sources OFF turn the System Reference Device SOURCE 1 ON All Sources should turn ON and any additional setup programming source select play etc should execute as programmed If any functions were missed test the individual ON Macro for that Source Re learn IR Commands and adjust delays as necessary until the system powers up correctly 16 Repeat Step 15 for System OFF Turn the System Reference Device SOURCE1 OFF Deleting IR Commands and Macros 17 Delete a Single IR command must be in EDIT mode Press and release the DELETE button The PROGRAM LED will blink once indicating that the IR command was deleted 18 Delete a Macro Press and hold approximately 2 seconds the DELETE button until the SOURCE active Source blinks once The PROGRAM LED will blink once indicating that the Macro was deleted 19 Delete All Macros Press and hold approximately 4 seconds the DELETE button until the SOURCE active Source blinks twice The PROGRAM LED will blink once indicating that all Macros were deleted Quick Start Manual ISM4 Intelligent System Manager 2008 Xantech Corporation Document 08905137D NOTES NOTES WARRANTY STA
6. ode Press and hold SEQUENCE until the active source blinks once and release to enter Edit Mode Source 1 and Program LEDs will turn ON solid green Navigate to the Macro to be tested 2 second press of PREV or NEXT and then press the TEST button Advance to Source 2 4 12 To advance to SOURCE 2 from Source 1 OFF Macro press and hold the NEXT button again until the SOURCE 1 LED blinks once and release The SOURCE 2 LED and the PROGRAM LED will turn ON solid green Repeat the sequence to advance to SOURCES 3 and 4 NOTE Pressing and holding the PREV button until the active Source LED blinks once will shift programming to the previous Macro i e pressing and holding the PREV button while in SOURCE 1 ON Macro Edit Mode will shift Edit Mode to the SOURCE 4 OFF Macro SOURCE 4 LED will turn ON solid green and the PROGRAM LED will turn on solid orange 13 Repeat Steps 2 11 above until all SOURCE ON and OFF Macros have been programmed tested and saved It is vitally important to program both the SOURCE ON and OFF Macros The ISM4 will not function properly if both sets of Macros have not been programmed Exit Edit Mode 14 To exit Edit Mode press and hold the PREV button release after the selected SOURCE LED blinks a second time about 2 seconds apart The ISM4 will return to Normal Operating Mode Test ISM4 All Macros NOTE All system devices and components must be properly setup and connected to test ISM4 Macro Programm
7. r Supply IR EMITTER DVD PLAYER SMVIDO1 To A V Receiver Input VIDEO SENSOR IR EMITTER CABLE BOX SMVLTO1 VOLTAGE SENSOR IR EMITTER AN RECEIVER SMVLTO1 VOLTAGE SENSOR IR EMITTER TV or VIDEO DISPLAY SMMAGO1 MAGNETIC SENSOR MACRO PROGRAMMING TABLE IR Command Brand Device Command PROGRAMMING INSTRUCTIONS The following instructions cover the basic Source programming procedure Each Source ON and OFF Macro can include up to five IR Commands Please refer to the ISM4 Installation amp Programming Manual for complete programming instructions To properly Program and Test IR Commands each of the Source IR Emitters must be connected to the appropriate ISM4 Source IR Out Port and attached to the appropriate device over the IR Eye If Source 1 is going to be turned ON OFF manually or with a remote control and there are no additional commands in the ON or OFF Macros it is not necessary to program the Source 1 ON or OFF Macros The ISM4 will sense the ON or OFF condition of Source 1 and automatically sync Sources 2 4 Learn IR 1 6 Enter Edit Mode Press and hold the SEQUENCE button until Source 1 LED blinks once and release The ISM4 will default to the SOURCE 1 ON Macro SOURCE 1 and PROGRAM LED s will turn ON solid green Note Read Steps 2 and 3 before entering macro commands Teach Command SOURCE 1 ON Ma
8. ransit is borne by the sender Xantech s warranty does not cover products which have been received improperly packaged altered or physically damaged Products will be inspected upon receipt Except as may be expressly provided and authorized in writing by Xantech Xantech shall not be subject to any other obligations or liabilities whatsoever with respect to equipment manufactured or sold by Xantech or services rendered by Xantech THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESSED AND IMPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ATTENTION TO OUR VALUED CONSUMERS To insure that consumers obtain quality pre sale and after sale support and service Xantech products are sold exclusively through authorized dealers and authorized distributors Xantech products are not sold online The warranties on Xantech products are NOT VALID if the products have been purchased from an unauthorized distributor or an online e tailer In order to determine if your Xantech re seller is authorized please call Xantech 800 843 5465 XANTECH PRODUCT go to xantech com warranty for model numbers WARRANTY DURATION Amplifiers year Limited HOM year Limited Xantech Corporation 13100 Telfair Avenue Sylmar CA 91342 3573 800 843 5465 FAX 800 492 6832 www xantech com xantech
9. t that has suffered normal cosmetic deterioration f to product which shall have been subjected to negligence misuse abuse accident or damage by circumstances beyond Xantech s control including but not limited to lightning flood electrical surge tornado earthquake or any other catastrophic events beyond Xantech s control or g to product which shall have been subjected to improper operation connected equipment failure or malfunction inadequate packing or shipping damage maintenance or storage or to other than normal use of service h if parts are no longer available to repair or replace the product or to provide a functionally equivalent product The foregoing warranties do not cover reimbursement for labor transportation shipping removal installation or other expenses which may be incurred in connection with repair or replacement All claims for product shipping damage must be processed within 3 days of receipt by You Supplied batteries are not covered by this warranty For the purpose of this warranty Lifetime is defined as seven 7 years from the discontinuance of sales of that product by Xantech A Xantech Return Authorization RA must be obtained from Xantech by You your installer or your distributor for product covered under this warranty Covered product must be sent to Xantech together with proof of purchase RA number prepaid and insured to Xantech Freight collect shipments will be refused Risk of loss or damage in t
Download Pdf Manuals
Related Search