Whirlpool 3LTE5243BN0 Washer/Dryer User Manual
Contents
1. 10 foam shipping pieces outward just enough to clear the washer lid Open the washer lid The latch under the dryer will hold lid open lid by pushing up on latch Close lid Read yellow card Use new hoses and washers that came completely out of washer Do Not cut shipping straps 3 shipping straps 1 1 E Read the yellow card Place hand on top of agitator when removing the shipping straps Firmly jerk then pull the three shipping straps up until each strap with key is completely removed from washer Put straps in the same area as other shipping pieces coupling washer 1 4 E Insert a large washer into each end of the inlet hoses Check that washers are firmly seated in couplings three shipping straps with keys Inlet valves are plastic Do Not overtighten or crossthread 1 5 E Attach inlet hose to bottom inlet valve opening first Attach second inlet hose to top inlet valve Tighten couplings by hand then use pliers to make an additional two thirds turn Do Not overtighten this could cause damage to coupling fp roves ae Numbers correspond to steps Na ae mep ez euwe o Numbers correspond to steps IMPORTANT THIS PROCEDURE MUST BE FOLLOWED TO ASSURE PROPER INSTALLATION 1 4 clamp 64 cm max drain drain le 174 connector hose 64 cm max 1 6 E To prevent the drain hose from coming o2. Thin Twin Washer Dryer 230 Volt 50 Hz Installation Instructions IMPORTANT Read and save these instructions IMPORTANT Installer Leave ial P auetan with the hom Homeowner Keep instalation Instructions r future refere Save Installation instructions i for local electrical i inspector s use Part No 3397516 Before you start Check location where washer dryer will be installed Proper installation is your responsibility The washer dryer must not be installed or stored in an area where it will be exposed to water and or weather Make sure you have everything necessary for correct installation Earthed electrical outlet is required See Electrical requirements Panel A i Ta Standplpe drain system needs a two inch 6 cm diameter standpipe with a minimum carry away capacity of 17 gallons 64 liters per minute Top of standpipe must be at least 28 inches 71 cm high and no higher than a 48 inches 122 cm from Drain hose we inlets on back floor of washer have may also be 3 4 11 1 2 American installed to Floor draln system requires a siphon break Part No 285320 available from your authorized parts distributor Location should be large enough to fully open dryer door 90 See Recessed and closet installation instructions and Product dimensions Panel E N Yeo IS S a laundry tub B or floor drain CS Z
3. Installation Instructions for proper exhaust installation 12 30 5 cm minimum Mobile home installation outside wall floor enclosure This appliance Is sultable for mobile home Installations Mobile home exhaust requirements The washer dryer must have an outside exhaust If the dryer is exhausted through the floor and the area under the mobile home is enclosed the exhaust system must terminate outside the enclosed area Extension beyond the enclosure will prevent lint and moisture buildup under the mobile home Now start With washer dryer in laundry area INN INING Personal Injury Hazard More than one person Is required fo lift tilt or move the washer dryer because of Its weight and size Failure to follow this Instruction may result In personal Injury Truck only from the rear to prevent produce damage 1 E Put on safety glasses and gloves 2 Remove cardboard shipping base legs rear legs N 4legs 2 small water hose drain hose clamp washers 1 plastic beaded e 1 small clamp strap 2 faucet adapters 4large water drain hose adapter hose washers and clamp not shown 3 E Remove parts from plastic package Check that all parts were included 4 E insert a rear leveling leg into the hole in the rear corner on the bottom of the washer dryer Push leg in until it snaps into place Do the same same thing with the other leveling leg in the other
4. Ly system E X KI gt See Panel D Important Observe all governing codes and ordinances Check code requirements Some codes limit or do not permit the installation of clothes dryers in garages closets mobile homes and sleeping quarters Contact your local building inspector Check ufllltles Proper electrical supply must be available See Electrical requirements Panel A Hot and cold water faucets must be within 4 feet 122 cm of the back of the washer dryer and provide water pressure of 5 100 psi 34 5 689 6 kPa The hot and cold standard threads Level floor Maximum slope under washer dryer 1 inch 2 5 cm Support Floor must be sturdy enough to support washer dryer weight with water and clothes of 375 pounds 170 kilograms A WARNING Personal Injury Hazard More than one person Is required fo lift tlit or move this washer dryer because of Its welght and size Fallure to follow these Instructions may result In personal Injury Fire Hazard Do Not use or store gasoline paint thinners and other flammable materials near washer dryer Fumes from such materials could result In fire or explosion Never Install washer dryer up against draperies or curtalns or on carpet To do so may result In a flre Keep any and all Items from falling or collecting behind the washer dryer Fallure to do so may result In a fire Replace all access panels before operating washer dr
5. a fire Do Not exhaust the dryer Into a chimney furnace cold alr duct attic or crawl space or any other duct used for venting Clean the exhaust system every year Accumulated lint could be fuel for a fire or cause molsture damage e Exhausting your dryer Indoors Is Not recommended The molsture and lint Indoors may cause Lint to gather Inside and around the dryer and be a fuel for flre Moisture damage to woodwork furniture paint wallpaper carpet etc Housecleaning problems and possible health problems Fallure to follow these Instructions could result In fire damage personal Injury or health problems If using an existing exhaust system clean lint from entire length of exhaust system Make sure exhaust hood Is not plugged with lint The exhaust system should be Inspected and cleaned yearly Replace any vinyl or metallized plastic foll exhaust duct with rigid metal or flexible metal duct Use duct tape to seal all joints Do Not use screws to secure duct exhaust air flow better good Four Inch 10 2 cm rigid metal pipe is preferred Plan installation to use the fewest number of elbows and turns Metal flexible duct must be fully extended and supported when the dryer is in its final position DO NOT KINK OR CRUSH THE DUCT The metal flexible duct must be fully extended to allow adequate exhaust alr to flow Allow as much room as possible when using elbows or making turn
6. breaker is not tripped or the house fuse blown e Check that power supply cord is plugged into wall receptacle e Check that washer lid or dryer door is closed e Check that controls are set in a running or ON position e Check that dryer START button has been firmly pushed Part No 3397516 1995 Whirlpool Corporation If you need assistance Call your dealer or local authorized service company When you call you will need the washer dryer model number and serial number Both numbers can be found on the model serial rating plate located behind the dryer door on the dryer door well lt gt iflpd ol CORPORATION Prepared by Whirlpool Corporation Benton Harbor Michigan 49022 When moving the washer dryer Disconnect the power supply cord Tape power supply cord securely to washer dryer Tape the dryer drum to the front panel Tape the lint screen in place Tape the dryer door closed Wedge a blanket between the tub ring and cabinet top to restrict washer tub movement Turn front leveling legs all the way in Printed on recycled paper 10 post consumer waste 50 recovered materials Printed in U S A
7. raising back legs inch 2 5 cm off the floor so that the rear self leveling legs will adjust Gently lower the washer dryer to the floor Check that the washer dryer is level by placing a carpenter s level on top of the washer first side to side then front to back If it is not level adjust the front legs up or down Tilt the washer dryer forward raising back legs inch 2 5 cm off the floor so that the rear self leveling legs will adjust Gently lower the washer dryer to the floor Check that the washer dryer is level Repeat as needed CHECK THAT DRAIN HOSE IS NOT TWISTED OR KINKED AND IS SECURELY IN PLACE strap strap strap 2 3 E Make sure the hook end of drain hose is in laundry tub or standpipe Wrap the plastic beaded strap around the drain hose and laundry tub or standpipe Thread beaded end of strap through keyhole end Pull until strap is tight Slide strap into narrow end of keyhole to lock strap in place See Figures A B If the water inlet faucets and drain standpipe are recessed tightly wrap the plastic beaded strap around the drain hose and faucet body Do Not wrap strap around the faucet handles or stems Thread beaded end of strap through keyhole end Pull until strap is tight Slide strap into narrow end of keyhole to lock strap in place See Figure C Secure the draln hose to the laundry tub or standpipe with the plastic beaded strap Fallure to properly s
8. two foam shipping pieces between the washer and dryer and place with the other shipping pieces Remove the two Phillios head screws located at the top of the access panel See illustration for Step 24 Remove access panel and set access panel and screws aside Complete the following steps through the access area Panel D 19 E Put hook end of drain hase into laundry tub or standpipe Check for proper length of drain hose 20 attaching water inlet hoses run water through both faucets into a bucket This will get rid of any particles in water lines that might clog hoses Mark which is the hot water faucet larger faucet smaller coupling washer adapter washer Inlets are plastic DO NOT STRIP OR CROSSTHREAD e For both Inlet hoses Insert larger washer into end of coupling then attach faucet adapter Insert smaller washer into end of faucet adapter Make sure washers are firmly seated into couplings Attach bottom hose with adapter inlet marked H to hot water faucet Attach top hose with adapter inlet marked C to cold water faucet Tighten couplings to faucets by hand then use pliers to make final two thirds turn Do Not overtighten this could cause damage to coupler Move washer dryer to its permanent position Remove cardboard hardboard from under washer dryer 2 2 E Carefully move the washer dryer into final position Tilt the washer dryer forward
9. al exterior wall opening around exhaust hood 2 y W CHECK ELECTRICAL REQUIREMENTS BE SURE YOU HAVE CORRECT ELECTRICAL SUPPLY AND RECOMMENDED EARTHING METHOD Check the Installation Instructions to see that you have completed each step Complete any missed steps before you continue i 23 E Check that all parts are now Installed See parts list Panel B If there is an extra part go back through the steps to see which step was skipped 29 E Check that you removed all the shipping pieces including the three shipping straps with keys Dispose of all materials in proper manner If you do not remove alll three shipping straps your washer dryer may walk away trom Its location EE ae 3 0 E Check that you have all your tools 3 1 Eum on water faucets and check for leaks Tighten couplings if there is leaking DO NOT OVERTIGHTEN This could cause damage to faucets 3 2 E Replace the access panel Be sure to tighten screws at each end of the access panel 3 3 E Plug power supply cord into earthed outlet 3 4 E Read the Use and Care Guide to fully understand your new washer dryer Now start the washer and allow it to complete the regular cycle Panel E 0 0 cm y 3 5 E Remove tape from dryer door and open dryer door Remove tape across the dryer lint screen Check to be sure lint screen is in its proper position Wipe out drum with a damp cloth to rem
10. aln system needs a 20 gallon 76 liters laundry tub Top of laundry tub must be at least 28 inches 71 cm high and no higher than 48 inches 122 cm from floor If a longer drain hose is needed drain hose Part No 388423 and hose connection kit Part No 285442 are available from your authorized parts distributor Dryer may be exhausted from rear or left or right side Exhausting through the side requires side exhaust kit Part No 279823 See Exhaust requirements Panel B Four Inch 10 2 cm metal exhaust duct Is required SEE RECESSED AND CLOSET INSTALLATION gt S INSTRUCTIONS ON PANEL E CAUTION Product Damage Do Not store or operate washer dryer below 32 F 0 C some water may remain in washer Proper operation of dryer cycles requires temperatures above 45 F 7 C See Use amp Care Guide for Winterizing Information Fallure to follow these Instructions may result In damage from freezing Power supply cord This appliance is equipped with a 15 amp rated Schuko type power supply cord strain relief Two wire power supply cord Figure 1 electrician determine that the earthing path Is adequate A two wire plus earthing wire single phase 230 volt 50 Hz AC only 15 ampere electrical supply is required on a separate circuit A time delay fuse or circuit breaker is recommended Recommended earthing method For your personal safety this appliance must be earth
11. ecure drain hose could result In water damage If draln hose cannot be strapped Into place hose must be cut exactly to length so hook end Is held tightly over edge of laundry tub or standpipe See Figure D If a longer drain hose is needed drain hose Part No 388423 and Hose Connection Kit Part No 285442 are available from your authorized parts distributor If drain hose must be shortened use Hose Connection Kit Part No 285442 Note If washer dryer Is moved to adjust drain hose the washer dryer must be leveled again Repeat Step 22 Place cardboard under the washer dryer and carefully move washer dryer to avoid damaging floor covering 24 E If you did not remove the access panel in Step 18 remove the two foam shipping pieces between washer and dryer and place with other shipping pieces If exhaust duct cannot be connected from the side of the washer dryer exhaust duct can be reached from the front through the access panel Remove the two Phillips head screws located at the top of access panel Set access panel and screws aside 2 5 Determine the length of exhaust duct that is needed to connect the dryer to the exhaust hood See Exhaust requirements Panel B 26 Connect exhaust duct to washer dryer and then to the exhaust hood e Use the straightest path possible to eae 90 turns e Use duct tape to seal all joints in the exhaust system duct tape e Use caulking compound to se
12. ed This appliance is equipped with a Schuko type power supply cord To minimize possible shock hazard the cord must be plugged into a mating wall receptacle See Figures 1 and 2 1 4 socket wrench or nut driver slip joint pliers that open to 1 1 2 minimum Panel A two wire receptacle Figure 2 If your electrical requirements are different contact your authorized service center or a qualified electrician Direct wire The dryer can be connected directly to the fused disconnect or circuit breaker box with two wire or three wire flexible armored or non metallic sheathed copper cable with earthing wire Do Not use two wire with bare earthing wire All current carrying wires must be insulated A conduit connector must be installed at the junction box USE ONLY 10 GAUGE SOLID COPPER WIRE DO NOT USE ALUMINUM WIRE Allow four feet of slack in the line so the dryer can be moved if servicing is ever necessary Exhaust requirements A WARNING Fire Hazard Do Not use non metal flexible duct Do Not use metal duct smaller than 4 Inches 10 2 cm In diameter Do Not use exhaust hoods with magnetic latches e Check that exhaust system Is not longer than specified Exhaust systems longer than specified will Accumulate lint Shorten the life of the product Reduce performance and result In longer drying times and Increased energy usage Fallure to follow specifications may result in
13. ff or leaking it must be installed per the following instructions 1 Wet the inside end of the drain hose with tap water DO NOT USE ANY OTHER LUBRICANT squeeze ears of small clamp with pliers to open clamp and place clamp over end of drain hose 3 While holding clamp open work end of drain hose onto drain connecter 4 Position clamp over the drain hose area marked clamp Release clamp Clamp should be1 4 inch 64 cm from end of drain hose 1 y E Standpipe or laundry tub draln system Open hose clamp and slide over hook end of drain hose to secure the rigid and corrugated sections together Nh Floor drain system Do Not install hook end of drain hose to corrugated section Consult your plumber for proper installation It drain hose does not fit into standpipe install adapter Open other hose clamp with pliers and place clamp over rigid end of drain hose Insert tapered end of adapter into rigid end of drain hose up to stops on the sides of adapter Secure with clamp Slide washer dryer onto cardboard or hardboard before moving across floor to avoid damaging floor 1 8 E if you have room to work from elther side of the washer dryer move washer dryer close to final position so you can easily complete the installation steps It you are working In a closet or recessed area move the washer dryer into final position and remove cardboard hardboard from under washer dryer Remove the
14. ove any dust Start dryer and allow it to complete a heat cycle to make sure the dryer is working properly 3 6 E Finally save all literature and keep with washer dryer You have just finished installing your new Whiripool washer dryer To get the most efficient use from your new Whirlpool washer dryer read your Use amp Care Gulde Congratulations Keep Installation Instructions nearby where you can refer to them They ll make reinstalling your Whirlpool washer dryer In another home as easy as the first Installation Recessed and closet installation instructions AWARNING Flre Hazard It ls recommended that the washer dryer be exhausted to the outside If washer dryer Is Installed In a closet the dryer MUST be exhausted outside Fallure to do so may result In a fire TO PREVENT LARGE AMOUNTS OF LINT AND MOISTURE FROM ACCUMULATING IN THE RECESSED AREA TO MAINTAIN DRYING EFFICIENCY AND TO PREVENT EXPOSURE TO POSSIBLE HEALTH HAZARDS THIS APPLIANCE SHOULD BE EXHAUSTED OUTDOORS This washer dryer may be installed in a recessed area or closet The installation spacing is in inches and centimeters and is the minimum allowable Additional spacing should be considered for ease of installation servicing and compliance with local codes and ordinances if closet door is installed the minimum unobstructed air openings in top and bottom are required Louvered doors with equi
15. rear corner 5 E Push up one leg check to see that the other leg goes down Check the other leg the same way If legs do not adjust repeat Step 4 6 E With one of the front legs in hand check the ridges for a diamond marking That s how far the leg is supposed to go into the hole Start to screw the legs into the holes in the front corners by hand Use slip joint pliers to finish turning the front legs until you reach the diamond mark Slide washer dryer onto cardboard or hardboard before moving across floor to prevent damage to floor covering r E Place a piece of cardboard or hardboard in front of carton Now stand the washer dryer upright Slide washer dryer onto cardboard or a hardboard To prevent product damage Do Not remove comer posts inside the carton before cutting X B E With the corner posts in place cut the carton down one comer Remove carton Panel C y Numbers correspond to steps 9 Do Not Remove 9 E Remove the two rear corner posts located at the back of the washer dryer Remove the two corner pieces attached to the lower front of the washer dryer Do Not remove the foam shipping pieces between the washer and dryer until tne washer dryer is in place a P t l 1 2 E Remove yellow card Take hoses out of basket Place hoses with other parts
16. s Bend duct gradually to avoid kinking Remove excess flexible duct to avoid sagging and kinking that may result in reduced air flow The exhaust duct can be routed up down left right or straight out the back of the washer dryer Space requirements are provided on Panel E agR and on the rear panel zy of the washer dryer Use the straightest path possible to avoid 90 turns ER Panel B Maximum length of the exhaust system depends upon the type of duct used number of elbows and the type of exhaust hood The maximum length for both rigid and flexible duct is shown in the chart 4 4 10 2cm 10 2 cm 43ft 13 1m 41ft 125m 36ft 11 0m 33ft 10m 31ft 4m 26ft 7 9m 23t 70m 21ft 64m 16 ft 49m 18ft 55m 18ft 5 5m Not recommended 30 ft 9 1m 20f 88m 24ft 73m 24ft 7 3m 23ft 70m 18ft 5 5m 16ft 49m 7 15ft 46m 10ft 3 0 m 10 ft 3 0m 9ft 2 1m recommended The maximum length using a 2 x 6 rectangular duct with 2 elbows and a 2 1 2 TYPE C exhaust hood is 8 ft 2 4 m For exhaust configurations other than those listed in chart the back pressure MUST not exceed 0 2 inches water column at the back of the washer dryer The back pressure should be checked by a qualified technician For exhaust systems not covered by the exhaust length chart check with your dealer or distributor for information Service check The back pressure in any exhau
17. st system used must not exceed 0 2 inches of water column measured with an inclined manometer at the point that the exhaust duct connects to the dryer Exhausting the dryer outside is recommended Recessed installation that is not exnausted outside must use Exhaust Deflector Kit Part No 694609 available from your authorized parts distributor See Recessed and closet installation instructions Panel E for unobstructed air opening requirements It the washer dryer Is Installed in a confined area such as a bedroom bathroom or closet It must be exhausted fo the outside and provision must be made for enough air for ventilation Check governing codes and ordinances Also refer to the Recessed and closet installation instructions on Panel E An exhaust hood should cap the exhaust duct to prevent exhausted air from returning into dryer The outlet of the hood must be at least 12 inches 30 5 cm from the ground or any object that may be in the path of the exhaust Four Inch 10 2 cm outlet hood Is preferred However a 2 1 2 inch 6 4 cm outlet hood may be used with short systems only A 2 1 2 inch 6 4 cm outlet hood can result in longer drying times than other hood types For permanent Installation a stationary exhaust system Is required Exhausting the dryer through the side of the washer dryer requires the use of Side Exhaust Kit Part No 279823 available from your authorized parts distributor Follow kit
18. valent air openings are acceptable Closet installation must be exhausted Other installations must use the minimum dimensions indicated Recessed installation j 0 0 cm 3 7 6 cm gt side view front view Minimum Installation spacing Note If recessed installation is exhausted all spacing can be 0 inches 0 cm Additional clearance for wall door and floor molding may be required Closet installation Y 48 sq in a 310 sq cm 3 7 6 cm closet door 3 7 6 cm A 24 sq In 155 sq cm Ey front viow Unobstructed air openings are minimum for closet door Louvered door with equivalent air openings is acceptable pa 0 0 em 48 sq In 310 sq cm Additional closet space may door be needed for exhaust elbow 24 sq In 155 sq cm F 1 2 5 cm side view Closet installation must be exhausted outdoors Recessed non exhausted installation must use only the rear exhaust position and Exhaust Deflector Kit No 4500 is required Product dimensions Shown with legs extended 1 Inch 2 5 cm from bottom of washer dryer 12 30 5 cm coid 96 5 cm water inlet 28 5 8 72 7 cm 36 2 cm tecess width rear view 15 3 8 21 E 1 a KIRSA 27 5 8 70 2 cm 71 3 4 182 2 cm 5 1 4 13 3 cm 32 1 8 81 6 cm 27 1 4 69 2 cm side view If washer dryer does not operate e Check that the circuit
19. yer Fallure to follow these Instructions may result In a fire explosion or electrical shock Tools and materials needed for installation utility knife Electrical requirements A WARNING Electrical Shock Hazard Electrical earth Is required on this appllance Do Not earth to a gas pipe Do Not modify the power supply cord Plug if it will not fit the outtet have a proper outlet Installed by a qualified electrician Do Not reuse an old power supply cord Possible electrical shock or flre hazard could occur If old power supply cord Is used Do Not have a fuse In the neutral or earthing clircult A fuse In the neutral or earthing clircult could result In an electrical shock Do Not use an extension cord with this appliance Check with a qualifled electrician as to whether the appliance Is properly earthed Fallure to follow these Instructions could result In death or serious Injury If codes permit and a separate earthing wire Is used it Is recommended that a quallfled AWARNING Electric Shock Hazard It Is the customer s responslblilty To contact a qualified electrical Installer To assure that the electrical Installation Is adequate and In conformance with all local codes and ordinances Fallure to follow these Instructlons could result In death or serious Injury Water heater Set to deliver 140 F 60 C water to the washer Laundry tub dr
Download Pdf Manuals
Related Search