Whirlpool 3LER5436EQ0 Washer/Dryer User Manual
Contents
1. outside wall enclosure Moblie home exhaust requirements The dryer must have an outside exhaust If the dryer is exhausted through the floor and the area under the mobile home is enclosed the exhaust system must terminate outside the enclosed area Extension beyond the enclosure will prevent lint and moisture buildup under the mobile home 12 30 5 cm 3 m Remove the tape that holds the drum to the cabinet Gome dryer drums are not taped for shipping Move the drum by hand counterclockwise to make sure alll tape has been removed Wipe the interior of the drum thoroughly with a damp cloth before using the dryer from the carton and place them on the floor in back of the dryer 5 m Firmly grasp the body of the dryer and gently lay it on its back on the cardboard corners 6 m With one of the legs in hand check the ridges for a diamond marking That s how far the leg is supposed to go into the hole T E Start to screw the legs into the holes by hand Use a 1 2 5 cm socket wrench or other type wrench to finish tuming the legs until you reach the diamond marking CAUTION Floor Damage Slide dryer onto cardboard or hardboard before moving across floor Failure to do so may cause damage to floor covering 8 E Now stand the dryer up Slide dryer onto cardboard or hardboard 9 w Move the dryer close to its permanent location but leave enough room to connect exhaust duct Remove card2. between the wall and the appliance so that it can be moved if servicing is ever necessary A conduit connector must be provided at each end of the power supply cable at the appliance and at the junction box Wire sizes COPPER WIRE ONLY and connections must conform with the rating of the appliance 20 amperes Important Observe all governing codes and ordinances Grounding earthing instructions This appliance must be connected to a grounded earthed metal permanent wiring system or an equipment grounding earthing conductor must be run with the circuit conductors and connected to the equipment grounding earthing terminal or lead on the appliance Electrical connection THE ELECTRICAL CONNECTION OF THIS APPLIANCE MUST BE CARRIED OUT BY A LICENSED ELECTRICIAN AND MUST CONFORM WITH THE RELEVANT AUSTRALIAN STANDARDS Exhaust requirements 4 WARNING Fire Health Hazard Do Not use non metal flexible duct Do Not use motal duct smaller than four Inches 10 2 cm In dlameter Do Not use exhaust hoods with magnetic latches Check that exhaust system Is not longer than specified Exhaust systems longer than specified will Accumulate lint Shorten the life of the dryer Reduce performance resulting In longer drying times and Increased energy usage Fallure to follow specifications may result In a flre Maximum length of the exhaust system depends upon the type of duct used number of
3. A closet installation must be exhausted outside Recessed installation that is not exhausted outside must use Exhaust Deflector Part No 3391278 available from your dealer See Recessed and closet installation instructions Panel C for adequate unobstructed air opening requirements If the dryer Is Installed In a confined area such as a bedroom bathroom or closet it must be exhausted to the outside and provision must be made for enough air for combustion and ventilation Check governing codes and ordinances Also refer to the Recessed and closet installation instructions Panel C An exhaust hood should cap the exhaust duct to prevent exhausted air from returning into dryer The outlet of the hood must be at least 12 inches 30 5 cm from the ground or any object that may be in the path of the exhaust Four Inch outlet exhaust hood is preferred However a 2 1 2 inch 6 4 cm outlet exhaust hood may be used A 2 1 2 inch 6 4 cm outlet exhaust hood can result in longer drying times than other hood types For permanent Installation a statlonary exhaust system Is required Mobile home installation This appliance is suitable for mobile home installations The installation of the dryer must conform to the Manufactured Home Construction and Safety Standard Title 24 CFR Part 3280 formerly the Federal Standard for Mobile Homes Construction and Safety Title 24 HUD Part 280 1975 or the latest edition
4. DRYER MUST BE CONNECTED WITH COPPER WIRE ONLY 4 WARNING Electrical Shock Hazard It Is the customer s responsiblity To contact a quallfied electrical Installer To assure that the electrical Installation is adequate Fallure to do so could result In fire electrical shock or other personal Injury Fire Hazard Do Not store gasoline paint thinners or other flammable materlals near dryer Fumes from such materials may result In fire or explosion Never Install dryer up against draperles or curtains or on carpet Keep any and all Items from falling or collecting behind the dryer Fallure to follow these Instructions could result In a fire or explosion 4 WARNING Fire Hazard If you install the dryer In a garage carport or areas near vehicles where fumes from gasoline or other flammable materials may be present the vapors may be heavier than alr and remain near floor Place dryer a minimum of 18 inches 45 7 cm above floor Check with your bullding inspector regarding requirements for this Installation Fallure to follow these Instructions could result In fire or explosion Support Floor must be sturdy enough to support dryer weight of 150 68 kg pounds 3 The appliance may be connected directly to the fused disconnect or circuit breaker box through flexible armored or non metallic sheathed copper cable Allow two or three feet of slack in the line
5. Is required o 0 cem g 0 cm Recessed front view Minimum installation spacing Closet installation must be exhausted 48 sq in 309 7 sq cm ane 10 2 cm 24 sq in 154 8 sq cm 1 2 5 cm CURVERRALERRERRRRLERRLERRREEUEELELEEAT closet door 3 7 6 cm 48 sq in 309 7 sq cm TNA NATO NE Pa RA eT Bs ee 154 8 sq em Montana en 3 7 6 cm Front view Additional clearances for wall door and floor moldings may be required Opening is minimum for closet door Louvered door with equivalent air openings is aa OCCEePTAble Additional space is needed when external exhaust elbow is used If dryer does not operate properly If dryer will not operate check the following to be sure that A Electrical supply is connected B House fuse is intact and tight or circuit breaker has not tripped C Door is closed D Controls are set in a running or On position E Start button has been pushed firmly Part No 3394023 Rev A 1994 Whirlpool Corporation CAUTION Floor Damage Slide dryer onto cardboard or hardboard before moving across floor Failure to do so may cause damage to floor covering When moving your dryer Shut off electric supply to dryer Disconnect power supply cord and tape securely to dryer Tape the drum to the front panel Tape the dryer door and lint screen Screw l
6. elbows and the type of exhaust hood The maximum length for both rigid and flexible duct is shown in chart 25 ft 7 5 m 25 ft 7 5 m 18 f 5 4 m 19 ft 5 7 m 19 tt 5 7 m 12 f 3 6 m 15f 4 5 m 15 ft 4 5 m 10 ft 3 m Now start With dryer in laundry area 1 m If your dryer has tape at front corners remove tape 2 m Open dryer and remove literature and parts packages Remove drying rack if your dryer has one Remove parts from packages Check that all parts were included see Panel A The maximum length using a 2 5 1 cm x 6 15 2 cm rectangular duct with 2 elbows and a 2 1 2 6 4 cm TYPE C exhaust hood is 8 ft 20 3 cm Do Not exhaust dryer Into a chimney furnace cold air duct attic or crawl space or any other duct used for venting Clean the exhaust system every other year Do Not Install flexible duct In enclosed walls cellings or floors Accumulated lint could be fuel for a fire or cause moisture damage Exhausting your dryer Indoors Is Not recommended The molsture and lint Indoors may cause Lint to gather inside and around the dryer and be a fuel for fire Molsture damage to woodwork furniture paint wallpaper carpet etc Housecleaning problems and possible health problems Failure to follow these Instructions could result In fire damage property damage personal injury or health problems If using an existing exhaust system clean lint
7. from entire length of exhaust system Make sure exhaust hood Is not plugged with lint Replace plastic exhaust duct with rigid metal or flexible metal duct Use duct tape to seal all joints Four Inch 10 2 cm rigid metal pipe is preferred Plan installation to use the fewest number of elbows and turns better exhaust air flow good exhaust air flow Metal flexible duct must be fully extended and supported when the dryer is in its final position DO NOT KINK OR CRUSH THE DUCT The metal flexible duct must be completely open to allow adequate exhaust alr to flow Allow as much room as possible when using elbows or making turns Bend duct gradually to avoid kinking Remove excess fiexible duct to avoid sagging and kinking that may result in reduced air flow Exhaust outlet is located at the center of the bottom dryer back The exhaust duct can be routed up down left right or straight out the back of the dryer General space requirements are provided on Panel C Use the straightest path you can where possible to avoid 90 turns Panel B For exhaust systems not covered by the exhaust length chart check with your dealer or distributor for information Service check The back pressure in any exhaust system used must not exceed 0 6 inches 1 5 cm of water column measured with an inclined manometer at the point that the exhaust duct connects fo the dryer Exhausting the dryer outside is recommended
8. wrench Parts supplied for installation Remove parts from packages Check that all parts were included 4 leveling legs kega literature package Panel A 42 3 8 107 6 cm Important Observe all governing codes and ordinances Open dryer and remove literature and parts packages i 73 7 cm x Level floor 1 inch 2 5 cm maximum slope under entire dryer Electrical requirements A WARNING Electrical Shock Hazard Electrical ground earth Is required on thls applilance Do Not modify the power supply cord plug If It does not fit the outlet have a proper outlet installed by a qualified electician Do Not have a fuse In the neutral or grounding earthing circult A fuse in the neutral or grounding earthing clrcult could result in an electrical shock Do Not use an extension cord with this applilance Check with a quallfled electrician to be sure this appilance Is properly grounded earthed Do Not connect plug end of power supply cord Into a livo receptacle before connecting power supply cord to dryer terminal block Do Not reuse old power supply cord Fallure to follow these Instructions could result In serious Injury or death 1 A two wire plus grounding earthing wire single phase 240 volt 50 Hz AC only electrical supply is required on a separate 20 ampere circuit fused in the active line Time delay fuse or circuit breaker is recommended 2 THE
9. Installation Instructions Part No 3394023 Rev A IMPORTANT Read and save these instructions Electric Dryer IMPORTANT Installer Leave Installation Instructions ith the homeowner Homeowner Keep Installation Instructions for future reference Save Installation Instructions for local electrical inspector s use Home Appliances 1 94 Before you start Check location where dryer will be installed Proper installation is your responsibility The dryer must not be installed or stored in an area where it will be exposed to water and or weather Make sure you have everything necessary for correct installation Protection from the weather Proper operation of dryer cycles requires temperatures above 45 F 7 2 C or the dryer may not shut off when automatic cycles are used Check code requirements Some codes limit or do not permit installation of clothes dryers in garages closets mobile homes or sleeping quarters Contact your local building inspector Grounded earthed electrical supply Is required See Electrical requirements Panel A Four inch 10 2 cm metal exhaust duct is required Dryer Door Clearance Location must be large enough to fully open dryer door See Panel C for recessed and closet requirements 16 1 4 41 3 cm Full Width Hamper Door Tools and materials needed for installation flat blade screwdriver f 4 1 socket E
10. alling your new Whirlpool dryer To get the most efficient use form your new dryer read your Congratulations Whirlpool Use and Care guide Keep Installation Instructions and Gulde close to dryer for easy reference The Instructions will make reinstalling your Whirlpool Dryer In another home as easy as the first Installation Numbers correspond to steps closet door Recessed and closet installation instructions The dryer may be installed in a recessed area or closet WARNING Fire Hazard If the dryer Is Installed In a closet the dryer MUST be exhausted outside Fallure to do so may result In a fire TO PREVENT LARGE AMOUNTS OF LINT AND MOISTURE FROM ACCUMULATING TO MAINTAIN DRYING EFFICIENCY AND TO PREVENT EXPOSURE TO POSSIBLE HEALTH HAZARDS THIS DRYER SHOULD BE EXHAUSTED OUTDOORS The installation spacing is in inches and centimeters and is minimum allowable Additional spacing should be considered for ease Of Installation servicing and compliance with local codes and ordinances If closet door is Installed the minimum unobstructed air openings in top and bottom is required Louvered doors with equivalent air openings are acceptable Closet installation must be exhausted Other installations must use the minimum dimensions indicated Companion appliance spacing should be considered For recessed non exhausted Installation Exhaust Deflector Kit Part No 3391278
11. board or hardboard from under dryer 1 O The electrical connections must be done by a licensed electrician oOo aE 1 1 m Check levelness of dryer by placing level on top of the dryer first side to side then front to back If dryer is not level adjust the legs of the dryer up or down Dryer must be level to prevent noise and poor drying performance LATHE 1 2 m Connect exhaust duct to exhaust hood and dryer See Exhaust requirements Panel B Use the straightest path possible to avoid 90 tums Use duct tape to seal all joints in the exhaust system Use caulking compound to seal exterior wall opening around exhaust hood we eS se 1 3 Check that all parts you removed from the parts packages are now Installed in the dryer If there is an extra part go back through the steps to see which step was skipped Panel C 4 m Check to make sure you have alll the tools you started with 1 5 Carefully slide dryer into its final location Check to be sure legs were properly installed and dryer is level 1 6 E Read the Use and Care Guide to fully understand your new dryer Start the dryer and allow it to complete a full heat cycle not the air cycle After five minutes open dryer door You should feel heat inside the dryer If you do not feel heat follow instructions given on back cover If dryer does not operate properly You have Just finished Inst
12. eveling legs all the way in Before having your electric dryer installed in your new home check with a licensed electrician to confirm that the supply voltage matches the voltage specified on the serial rating plate CORPORATION Prepared by Whirlpool Corporation Benton Harbor Michigan 49022 Printed on recycled paper 10 post consumer waste 50 recovered materials Printed in U S A
Download Pdf Manuals
Related Search