Vestax PMC-270A Musical Instrument User Manual
Contents
1. 5 SPLIT CUE ON OFF L PHONES LEVEL e MIN gt J a N O CO IJ IQ PHONES IN 6 fu O W PHONES PROGRAM INPUT SECTION INPUT PHONO 1 LINE 2 LINE 1 16 16 EFFECT J PRE OFF POST CUE 3 SIGNAL N O PROGRAM INPUT SECT ION 1 2 INPUT FADER INPUT SELECTOR Used to select input 2 line or 1 phono to be sent to each PGM channel TRIM CONTROL Adjusts the Input level of each channel Set INPUT FADER to 7 8position adjust TRIM so that the INPUT LEVEL METER shows about 0dB BALANCE CONTROL Adjusts the stereo balance for each PGM channel Can be used for adjusting the unbalanced stereo image caused by a strong anti skating setting Clockwise rotation from center position increases the volume of R over L channel A counter clockwise rotation increases the volume of L channel over R EQUALIZER HIMIDLOW Adjusts the HI MID LOW frequencies for each PGM channel Each band has following specifications HI kHz 12dB Shelving type MID 50082 16dB Peaking type LOW 80Hz 12dB Shelving type EFFECT SWITCH This switch enables the signal from each programs to be sent to AUX send jack Different signal routes can be selected this switch to different positions PRE The signal before the input fader after the EQ wi2. a i lS a 9 10 11 12 13 14 MASTER SECT ION 15 16 17 18 19 20 21 22 23 24 LINE INPUT JACK LINE 4 Input connectors for line level equipment such as CD playerstape decks DATs or M Ds etc MIC INPUT JACK MIC1 2 Input jacks of mic1 mic2 MIC LEVEL Adjusts the input level from all of the microphone inputs MIC EQUALIZER HIL OW Adjusts the HI and LOW frequencies for all of the microphone input EFFECT SWIT CH Used when sending signal to the external effect processor connected to the effect SEND RETURN CUE SWIT CH Used to send the signal from the mic channel to the monitor section for headphone monitoring MASTER SECTION MASTER CUE MASTER OUT LEVEL METER T he LED level meters indicate the signal level of the line out CUE LEVEL METER The LED level meters indicate the signal level of PGM input selected by CUE SWIT CH EFFECT SEND LEVEL Used to adjust the output level from EFFECT SEND signal is selected by the effect switch EFFECT RETURN LEVEL Dav Used to adjust the input level from the EFFECT RETURN RETURN JACK This EFFECT RETURN can be used as the sub line input EFFECT CUE SWIT CH cid MUS Used to send the signal from EFFECT RETURN Oy JACK to the monitor section for headphone OFF ON monitoring m MASTER MASTER BALANCE VOLUME HAS Adjusts the signal balance of left to the right side of the o
3. M Vestax Professional Mixing Controller PIMA OWNER S MANUAL VESTAX CORPORATION 2 37 1 Kamiuma Setagaya ku Tokyo 154 0011 Japan Phone 03 3412 7011 03 3412 7013 VESTAX America 2150 29th Ave Suite 115 Hollywood FI33020 Phone 954 926 6622 Fax 954 926 3304 VESTAX Europe Ltd 18 st Christophers Road Haslemere Surrey GU 27 1 DQ England Phone 0 1428 653117 Fax 0 1 428 6610 21 RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL lighting flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to consitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE RAIN OR MOISTURE CAUTION TO PREVENT ELECTRIC SHOCK MATCH BLADE OF PLUG TO WIDE SLOT FULLY INSERT ATTENTION POUR EVITER LES CHOCS ELECTRIQUES INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRIS
4. utilized for creating the ISOLAT OR SECTION effects of an acapella REAR PANEL rower Vestax PMC 270A ON OFF L j R L OUTPUT EFFECT MASTER OUT 1 SEND RETURN gt REAR PANEL 28 POWER SWIT CH T he first LED of MASTER OUT LEVEL METER that is located on the top panel is lit when on 29 AC POWER CABLE 30 OUTPUT JACK 1 4inch PHONE JACK PIN JACK Connect to the input of power amplifier 31 EFFECT SEND JACK Connect the SEND jacks to the input of an external effector unit Delay Reverb etc AC230V 50 60Hz 16W Vestax Corporation IN CHINA SERIAL NO 32 EFFECT RETURN JACK Connect the RETURN jacks to the output of the effector 33 PHONO INPUT JACK Input jack for PGM1 PGM2 and SUB channel turntables Connect turntables equipped with the MM pick up cartridge only 34 LINE INPUT JACK Input connectors for the line level equipment such as CD players tape decks DAT s MDs 35 GROUND TERMINAL Connect this terminal to the ground lead of the turntable T his helps to reduce noise and hum NOMINAL INPUT LEVEL IMPEDANCE FREQUENCY RESPONSE 20Hz 20kHz 0 3dB PHONO 42dB 470k S N RATIO 80dB LINE 100B 47k DIMENSION WXHXD W290mmX H80mm X D380mm MIC 42dB 303k WEIGHT 5kg EFFECT RCV 1088 47k RATED OUTPUT LEVEL IMPEDANCE LINE OUT 4dB 7 10K Q REC OUT 100 10 0 EFFECT SEND 100 10 0 Vestax Corporation
5. E POUSSER J USQU AU FOND IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS WARNING When using electric products basic precaution should always be followed including the following Read all the instructions before using the product Do not use this product near water for example near a bathtub washbowl kitchen sink in a wet basement or near swimming pool or the like This product should be used only with a cart or stand that is recommended by the manufacturer This product either alone or in combination with an amplifier and headphone or speakers may be capable of producing sound levels that could cause permanent hearing loss Do not operate for a long period of time at a high volume level or at a level that is uncomfortable Without you should consult an audiologist The product should be location or position does not interfere with its proper ventilation The product should be located away from heat sources such as radiators heat registers or other products that produce heat The product should be connected to a power supply only of the type described in operating instructions or as marked on the product 10 11 The power supply cord of the product should be unplugged from the outlet when left unused for a long period of time Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings The pr
6. e where there is high humidity and dust which may cause damage to internal parts Temperature Avoid use in hot over 35 C and cold below 5 C locations Keep the unit away from extreme direct heat such as direct sunlight heating radiators or closed vehicles for extended amount of time Power cord handling Connecting the power cord to other cords or joining cords together can cause fire and electric shock This is extremely dangerous Take precaution when handling AC plugs and connectors Handle only the plug or connector and do not perform these operations with wet hands Keep away from liquids Do not stand cans containing liquids on or near the equipment If liquid enters equipment disconnect the power cord from the power outlet immediately WARRANTY The warranty might vary from country to country Each distributor has their own warranty system in accordance with the country or state regulations or laws VESTAX observes the manufacturing country s regulations FEATURES Three band isolator switch kills each frequency range completely in quick action Pre Post selectable AUX send switch enables various effect processing The effect signal can be controlled by a dedicated return level control knob the signal can be also monitored by headphone when return is selected by cue button The new option meter allows DJs to monitor the cue signal visually The tempo can be matched by eyes as well as ears Thr
7. ee phono and 6 line inputs are provided to meet the new mixing style with various input source User replaceable 60 m m input faders and 45 m m cross fader make sight service very easy Optional input rotary volume can be replaced with the fader for House application Line 4 input jack RCA is located on the top panel This allows DJs to use hand carried DAT or MD player mixing with installed equipment TOP PANEL O Vestax m 4 SB m 2 m MC INPUT PHONO 1 INPUT LINE 2 PHONO 2 LINE 4 g LINE 3 PROGRAM INPUT SECTION PIMIG gt MIXING CONTROLLER CUE INPUT PHONO 3 LINE 6 MASTER SECTION LINE 5 0 TRIM TRIM eco e 5 MIN MAX MIN MAX e MIC BAL BAL BAL P MICROPHONE AND SUB INPUT D MIN MAX SECTION p R an i z L R MIN MAX ala EQ 16dB 16dB 16dB 16dB 16dB 16dB HI MID MAX RETURN 16dB 16 16 16 EFFECT OFF POST PRE OFF POST CUE SIGNAL C2 IN CO O m PGM1 ISOLATOR ISOLATOR SECTION A N Q 4 12dB 12dB LOW 12 8 LOW Q m S gt 16dB 160B 16dB 16dB OFF ON EFFECT EFFECT PRE OFF POST PRE OFF POST BAL CUE CUE Y gt Y OFF OFF SIGNAL SIGNAL LEVEL Q
8. ll be sent to AUX output POST The signal after the input and cross fader will be sent to AUX output OFF No signal will be sent to AUX output CUE SWIT CH Used to send the signal from each program to monitor section for headphone monitoring Used to adjust the Input level of each program Usually set at the 7 8 position T his is a detachable fader for emove four screws SELL the ease of replacement Replace with BEL the IF 27 when it is worn out S J HOW TO REPLACE THE INPUT FADER M Remove the multi Remove four screws which hold the M EU ran fader unit panel lt T ake the unit out with the panel X Carefully remove the multi cable connector from the fader unit insert the connector to the new fader unit Put the fader unit panel in position and tighten the screws fay i Remove the multi cable connecter from fader unit 8 CROSS FADER When the Input level of PGM1 and 2 are properly set PGM 1 will be heard with the cross fader set to the left side PGM2 will be heard with the cross fader set to the right side When the cross fader is set in the center both programs will be heard This is detachable fader for the ease of replacement with CF R when it is worn out Remove four screws MICROPHONE SUB INPUT SECTION MICROPHONE SUB INPUT SECTION m 4 0 A rA Sem sy
9. oduct should be serviced by qualified service personnel when A The power supply cord or the plug has been damaged B Objects have fallen or liquid has been spilled into the product or C The product has been exposed to rain or D The product does not appear to operate normally or exhibits a marked change in perfromance or E The product has been dropped or the enclosure damaged Do not attempt to service the product beyond that described in the use maintenance instructions All other servicing should be referred to qualified service personnel CONGRATULATIONS Thank you for purchasing the VESTAX PMC 270A Professional Mixing Controller AS The top of the line the PMC 270A is a high specification mixer designed to meet the most professional requirements of the Dance Music DJs Please read this owner s manual carefully before you start to use your mixer so that you will fully understand all of the special features and enjoy the full use of the product IMPORTANT PRECAUTIONS To prevent electric shock do not remove the cover No user serviceable parts inside Please refer servicing to a VESTAX Authorized Service Center Always disconnect all equipment from the main supply when disconnecting or reconnecting signal leads The power cord should be connected last Make sure that the power switch is off when connecting the power cord Disconnect from AC supply when equipment is not used Humidity and dust Avoid us
10. utputs from the OUTPUT jack on the rear L R panel MASTER LEVEL VOLUME Adjust the signal level output from the output jack on the rear panel SPLIT CUE SWIT CH MIN MAX When this switch is ON the master signal is always heard through the right of the headphone The CUE signal will be heard in the left earcup when that input is selected by the CUE SWITCH 5 14 oo This enables both programs to be monitored simultaneously thus assisting in beat mixing HEAD PHONE LEVEL id A djusts the headphone output level HEAD PHONE JACK Use this jack to connect the headphones the impedance 8ohm to 600ohm can be used 150ohm is recommended JAX PHONES IN ISOLAT OR SECTION 25 HI SWIT CH Allows cutting off the sound of treble range Sound volume will be cut when the switch is set downwards When the switch is put back the output volume returns to normal Can be useful for cutting off the sound of the cymbals or high hats for example 26 MID SWIT CH Allows cutting off the sound of the middle range Sound volume will be cut when the switch is set downward position When the switch is put back the output volume becomes normal sound volume Can be used for cutting off vocal and melody from the source 27 LOW SWIT CH LO Allows cutting off the sound of the bass range Sound volume will be cut when the switch is set downward When the switch is put back the output volume return to normal Can be
Download Pdf Manuals
Related Search