Univex WFS709TP Switch User Manual
Contents
1. Introduction v1 0 May 2007 Chapter 2 Installing the Chassis This chapter covers the following topics e Pre Installation Checklist e Precautions e Requirements e Mounting the Chassis e Connecting Power e Verifying the Installation A Warning Installation should be performed by a trained technician Pre Installation Checklist Inspect the package to ensure that the following components shipped with your WFS709TP ProSafe Smart Wireless Switch e WES709TP ProSafe Smart Wireless Switch e Four 12 24 screws for attaching the chassis to an equipment rack e AC power cord rated to at least 10 A with IED320 connector e RS 222 serial cable with RJ 45 male connectors and serial adapter to connect the serial cable to a terminal or PC with a DB 9 serial port e Ethernet cable Installation Guide WFS709TP ProSafe Smart Wireless Switch Quick Install Guide Resource CD e Support Information Card e Warranty Card 2 1 v1 0 May 2007 WFS709TP ProSafe Smart Wireless Switch Hardware Installation Guide During installation you will need a Phillips or cross head screwdriver EE Note There should be another person available to help position the chassis Precautions Observe the following precautions during installation Hazardous energy is always present while the WFS709TP is plugged into an electrical outlet Remove all rings jewelry and other potentially cond2. WFS709TP ProSafe Smart Wireless Switch Hardware Installation Guide NETGEAR NETGEAR Inc 4500 Great America Parkway Santa Clara CA 95054 USA 202 10264 01 May 2007 2007 by NETGEAR Inc All rights reserved Technical Support Please refer to the support information card that shipped with your product By registering your product at http www netgear com register we can provide you with faster expert technical support and timely notices of product and software upgrades NETGEAR INC Support Information Phone 1 888 NETGEAR for US amp Canada only For other countries see your Support information card E mail support netgear com North American NETGEAR website http www netgear com Trademarks NETGEAR and the NETGEAR logo are registered trademarks of NETGEAR Inc in the United States and or other countries Other brand and product names are trademarks or registered trademarks of their respective holders Information is subject to change without notice Statement of Conditions In the interest of improving internal design operational function and or reliability NETGEAR reserves the right to make changes to the products described in this document without notice NETGEAR does not assume any liability that may occur due to the use or application of the product s or circuit layout s described herein Certificate of the Manufacturer Importer It is hereby certified that the WFS709TP ProSafe Smart Wireless
3. 2 4 Installing the Chassis v1 0 May 2007 WFS709TP ProSafe Smart Wireless Switch Hardware Installation Guide 12 24 screws 4 d Figure 2 1 e Use a Phillips or cross head screwdriver to secure the chassis to the rack with two 12 24 screws included for each mounting bracket Note Some racks require different screws which are not included Make sure that you use the correct screws or fasteners for your rack system 3 Ensure that there is adequate clearance around the chassis Figure 2 2 on page 2 6 e For proper air circulation leave at least 10 cm 4 inches clearance for the vents on the left and right of the chassis e Allow additional space in front and back of the chassis to access power cords network cables and indicator LEDs Installing the Chassis 2 5 v1 0 May 2007 WFS709TP ProSafe Smart Wireless Switch Hardware Installation Guide Keep Clear for Air Intake PEN 7 Keep Open to Access L Keep Clear for Air Exhaust Keep Open to Access Figure 2 2 Connecting Power A Warning This procedure should be performed by a trained technician 1 Make sure you understand the procedure and all precautions Before beginning read the entire procedure Make sure you understand all the precautions in these steps as well as those listed on page 2 2 2 Make sure that your site s electrical system is compatible with the WFS709TP See
4. MAC address SSID and location based authentication e Unifies wireless and wired access without compromising on security mobility or performance e Provides centralized management and monitoring of the wireless infrastructure e High speed Layer 2 Layer 3 packet forwarding v1 0 May 2007 WFS709TP ProSafe Smart Wireless Switch Hardware Installation Guide e 1U chassis can be mounted in a standard 19 inch network equipment rack e The firmware can be easily upgraded as future software releases are made available You can install upgrades using HTTP Front and Rear View The standard version of the WFS709TP ProSafe Smart Wireless Switch contains a 1000BASE T copper Gigabit Ethernet GE connector Figure 1 1 shows the front and rear views of the switch 5 Figure 1 1 System Indicator LEDs 7 The system LEDs located on the front of the switch display the status of system power and operation Table 1 1 System LEDs LED State Description Power Green WFS709TP is receiving proper power Off WFS709TP is powered off Status Green WFS709TP has booted and is functioning properly Off WFS709TP is booting loading software or has failed Note This LED remains off until you perform the initial setup described in the document nstallation Guide WFS709TP ProSafe Smart Wireless Switch 1 2 Introduction v1 0 May 2007 WFS709TP ProSafe Smart Wireless Switch Hardware Installati
5. May 2007 Appendix A Cables and Connector Pinouts Fast Ethernet Network Ports A 1 XS HN e Ut NERA A E A UMS A 1 cp M E A 1 GE DE PORC unice UH bp ebria Gau boa rrr intr eters Terry HEU tre Tre a pni A 2 TODOBASE T Copper GE CADIE sis cc cst sonus tort nba ao te usu iiA A 2 Sanal One PORE aueseiscalisssisdeuit et aU AME Lacu t I Lsc AM OL CODEC PHI RAM PE RM MM EDUC OR M D MMc NDA EU EE A 3 Fon anddapter FINOU a a dept oiiR a ped Ria ee ES A 3 Ganse Terminal Seis uude Lec uplddb bre I IUE pue Quei a A 4 Appendix B Specifications Bes deltas Eee TA RM E E mers he Teer rer reer E hearer tr B 1 cir Ij eem TT B 1 CODE AQ usen cem acted hin tap Coca trae o Go oa cecullun Fo tasa an Ex eio d Ko Du Kota oda E atu Tap Ue B 2 Appendix C Related Documents viii v1 0 May 2007 About This Manual The WFS709TP ProSafe Smart Wireless Switch Hardware Installation Guide describes how to install the WFS709TP ProSafe Smart Wireless Switch The information in this manual is intended for trained technicians responsible for installing this product Conventions Formats and Scope The conventions formats and scope of this manual are described in the following paragraphs e Typographical Conventions This manual uses the following typographical conventions Italic Emphasis books CDs file and server names extensions Bold User inpu
6. SRB Et 7 7101 T 9L BOA t ASAE 0 AS Fyi Hepy eror eg un ci IYE MAE 78e D 7 HLC Australia New Zealand This product complies with AS NZS CISPR 22 Class A standards Rest of World This product complies with CISPR 22 Class A standards Lithium Battery Safety Notice This product contains a lithium battery which is replaceable only by a trained technician Caution The lithium battery may explode if it is incorrectly replaced A trained technician should replace the battery with the same or equivalent type battery recommended by the manufacturer Dispose of used batteries according to the manufacturer s instructions v1 0 May 2007 European Union RoHS Netgear products comply with the EU Restriction of Hazardous Substances Directive 2002 95 EC RoHS EU RoHS restricts the use of specific hazardous materials in the e manufacture of electrical and electronic equipment Specifically restricted materials Sp KAT under the RoHS Directive are Lead including Solder used in printed circuit assemblies Cadmium Mercury Hexavalent Chromium and Bromine compounds of PBB and PBDE Some Netgear products are subject to the exemptions listed in RoHS Directive Annex 7 Lead in solder used in printed circuit assemblies Products and packaging will be marked with the RoHS label shown at the left indicating conformance to this Directive la China RoHS Netgear products comply with China environmental declaration requir
7. The WFS709TP ProSafe Smart Wireless Switch is shipped with mounting brackets already attached so that you can mount the chassis into a standard 19 inch equipment rack z2 Note The four 12 24 screws included with the WFS709TP are intended for securing the chassis to the rack Some racks require different sized screws which are not included Make sure that you have the correct screws or fasteners for your rack system before attempting to mount the chassis The WFS709TP like other network and computing devices requires compliance with operational specifications Reliable power Make sure that your electrical outlet is compatible with the WFS709TP For power requirements see Appendix B Specifications Power cords must be rated to 10 A and must conform to grounded electrical standards in the country in which the WFS709TP operates Use of a power line conditioner or Uninterruptible Power Supply UPS can decrease or mitigate problems caused by power service fluctuations Make sure that the output of any power shaping device is compatible with the WFS709TP power supply Cool non condensing ventilation For operating environment information see Appendix B Specifications Where a large number of electrical devices are running in the same area additional air conditioning or air circulation equipment may be required Ample space For proper air circulation leave at least 10 cm 4 inches clearance for the vents on
8. the physical and logical management and configuration of routers switches servers and clients This phase involves the following tasks e Use the console to perform initial configuration of the WFS709TP e Attach the WFS709TP to the network Planning the location of access points and air monitors Introduction 1 7 v1 0 May 2007 WFS709TP ProSafe Smart Wireless Switch Hardware Installation Guide You can manually determine the locations for APs or use a Web browser to access the switch s built in RF Plan tool and perform the following tasks e Define the physical site parameters Determine how many access points are needed and where they should be located e Simulate network failures and recovery characteristics and adjust placement if necessary Physical installation of the Wireless Access Points Refer to the document Installation Guide WFS709TP ProSafe Smart Wireless Switch and to the documentation included with your access points Advanced configuration of the WFS709TP ProSafe Smart Wireless Switch Configuration requires someone who understands the company s network and has experience managing routers switches servers and clients The following tasks are involved e Configure the planned network features via the Web interface e Test and verify the deployment The WFS709TP ProSafe Smart Wireless Switch Software Administration Manual provides information and examples of the switch s more advanced features
9. Appendix B Specifications Note Use of a power line conditioner or Uninterruptible Power Supply UPS can decrease or mitigate problems caused by power service fluctuations Make sure that the output of any power shaping device is compatible with the WFS709TP power supplies 2 6 Installing the Chassis v1 0 May 2007 WFS709TP ProSafe Smart Wireless Switch Hardware Installation Guide 3 Make sure that the power supply can handle the connected Power over Ethernet PoE devices Note The total power drawn by all connected PoE devices must not exceed 100 Watts For power ratings for NETGEAR APs refer to the access point p g p installation guide 4 Attach the power cord to the power input socket at the back of the chassis Plug an appropriate power cord into the power input socket Use the included power cord if it is compatible with your electrical outlet Otherwise replace the power cord with the type appropriate for your country The power input socket accepts a power cord with a standard IEC320 connector Warning For proper safety and performance the power cord must be rated to 10 A A and conform to grounded electrical standards in the country where the product is operated 5 Attach the power cord to a proper electrical outlet to power up the WFS709TP A Warning For safety reasons make sure the power outlet and plug are within easy reach of the operator and can be qui
10. FS709TP ProSafe Smart Wireless Switch Software Administration Manual The Resource CD provides a link to this manual or you can download it from http www netgear com support WFS709TP Software This software integrates the switch and APs to provide load balancing rate limiting self healing authentication mobility encryption and centralization for monitoring and upgrades This software is integrated into the switch and access point Deployment Summary This section outlines the tasks involved in deploying the WFS709TP ProSafe Smart Wireless Switch E d Administration Manual from the NETGEAR website at hitp www netgear com Note You can download the WFS709TP ProSafe Smart Wireless Switch Software support 3 Physical installation of the WFS709TP ProSafe Smart Wireless Switch Installation requires a trained technician who is experienced with handling and installing similar equipment This phase involves the following tasks e Transport unpack and mount the switch in a suitable rack environment e Attach power and a console e Boot the system and perform the initial power on test examining the LEDs and console messages to ensure proper operation Chapter 2 Installing the Chassis in this document provides the necessary instructions Initial configuration of the WFS709TP ProSafe Smart Wireless Switch Configuration requires someone who understands the company s wired network and has experience with
11. Switch has been suppressed in accordance with the conditions set out in the BMPT AmtsblVfg 243 1991 and Vfg 46 1992 The operation of some equipment for example test transmitters in accordance with the regulations may however be subject to certain restrictions Please refer to the notes in the operating instructions The Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on the market and has been granted the right to test the series for compliance with the regulations Bestatigung des Herstellers Importeurs Es wird hiermit best tigt dab das WFS709TP ProSafe Smart Wireless Switch gem der im BMPT AmtsblVfg 243 1991 und Vfg 46 1992 aufgef hrten Bestimmungen entst rt ist Das vorschriftsm Bige Betreiben einiger Ger te z B Testsender kann jedoch gewissen Beschr nkungen unterliegen Lesen Sie dazu bitte die Anmerkungen in der Betriebsanleitung Das Bundesamt f r Zulassungen in der Telekommunikation wurde davon unterrichtet da dieses Ger t auf den Markt gebracht wurde und es ist berechtigt die Serie auf die Erf llung der Vorschriften hin zu berpr fen Regulatory Compliance Information This section includes user requirements for operating this product in accordance with National laws for usage of radio spectrum and operation of radio devices Failure of the end user to comply with the applicable requirements may result in unlawful operation and adverse action against the end use
12. ay 2007 WFS709TP ProSafe Smart Wireless Switch Hardware Installation Guide Port LNK ACT LEDs Each FE port has its own LNK ACT LED on the upper left side of the port During operation these LEDs provide the following Ethernet link status information Status Description Off No Ethernet link on the port Green An Ethernet link has been established on the port but no data is currently being transmitted or received Flashing Green The port is transmitting or receiving data The flashing rate is proportional to the network activity Amber The Ethernet link on the port is encountering errors Port PoE LEDs Each FE port has its own PoE LED on the upper right side of the port This LED provides the following PoE status information Status Description Off The port is disabled or the attached device has not requested power PoE is not being provided by the port Green PoE is being provided to the attached device Amber The attached device has requested power but POE is not being provided by the port ACCESS POINT STATUS LEDs Each FE port has an identically numbered Access Point Status LED that represents the status of APs connected to that port on the WFS709TP ProSafe Smart Wireless Switch During operation the LEDs provide the following AP status information Status Description Red solid An AP on this port has failed highest precedence Red flashing An air monitor on this port has det
13. cable with a male connector Pinouts are shown in Figure A 2 Serial RJ 45 Female Console Port Pin Out 1 2 l Je 288 a7 i R 5 GND ENN XS RxD 8 Direction Input 4 Output Figure A 2 Cables and Connector Pinouts A 3 v1 0 May 2007 WFS709TP ProSafe Smart Wireless Switch Hardware Installation Guide To connect the required RS 232 serial cable to a terminal with a DB 9 male port use the included adapter Pinouts are shown in Figure A 3 RJ 45 Female Internal DB 9 Female Pin Out Connections Pin Out f RJ 45 DB 9 ix J 3 TxD 3 TxD 2 9e 5 Ground 4 4 ge ea 5 GND 5 GND 5 7e 3 RxD Mo ten 6 RxD 3 clo o PEED 8 Direction T Direction Input 4 TN Input 4 Output Output Figure A 3 Console Terminal Settings Table A 2 contains the settings for a console terminal connected to the serial port Table A 2 Console Terminal Settings Baud Rate Data Bits Parity Stop Bits Flow Control 9600 8 None 1 None A 4 Cables and Connector Pinouts v1 0 May 2007 Appendix B Specifications Physical Table B 1 Physical Specifications Item Specification Physical Dimensions Size Height 4 45 cm 1 75 inches Width 44 2 cm 17 4 inches Depth 33 0 cm 13 0 inches Weight 4 5 kg 10 Ib Shipping Dimensions Size H
14. ckly disconnected if necessary Once power is connected the WFS709TP automatically turns on and you can perform the power on test Verifying the Installation After the WFS709TP ProSafe Smart Wireless Switch is installed and connected to power verify the following 1 Check that the Power LED lights solid green immediately upon power up and remains solid green during and after boot Note The Status LED remains off until you perform the initial setup Installing the Chassis 2 7 v1 0 May 2007 WFS709TP ProSafe Smart Wireless Switch Hardware Installation Guide For more information on LED behavior see System Indicator LEDs on page 1 2 2 Check the fans to verify they are working You should be able to hear the fans operating and feel significant airflow blowing from the chassis vents at each of the three fan positions A Warning If one or more fans do not work immediately shut down and contact NETGEAR 3 Connect appropriate network cables see Appendix A Cables and Connector Pinouts for port and cable information 4 Perform the initial setup as described in Installation Guide WFS709TP ProSafe Smart Wireless Switch 2 8 Installing the Chassis v1 0 May 2007 Appendix A Cables and Connector Pinouts This appendix describes cables and connector pinouts for ports on the WFS709TP ProSafe Smart Wireless Switch Fast Ethernet Network Ports RJ 45 Pi
15. cp index htm http documentation netgear com reference enu glossary index htm Related Documents C 1 v1 0 May 2007 WFS709TP ProSafe Smart Wireless Switch Hardware Installation Guide C 2 v1 0 May 2007 Related Documents
16. ected an unsecured AP The AP is attached to your network but is not listed in the security policies If security policies are enabled clients are not granted access to your network through the unsecured AP Green flashing An air monitor on this port has detected interference The interfering device AP or other radio source has been detected by your valid APs but has no wired presence on your network Amber solid Load balancing is enabled on this port or an AP has reached the maximum number of clients it is configured to support Green solid All detected APs on this port are operating as expected Off No AP is detected on the port lowest precedence Introduction v1 0 May 2007 WFS709TP ProSafe Smart Wireless Switch Hardware Installation Guide The LED states are listed in order of precedence highest to lowest If more than one AP is connected to the port the state with the highest precedence is displayed GE Uplink Port 3 The WFS709TP ProSafe Smart Wireless Switch provides one Gigabit Ethernet GE 10 100 1000 Mbps 1000BASE T copper port for high bandwidth connection between the switch and the wired LAN The port automatically senses and negotiates speed duplex and MDI MDxX settings Figure 1 3 shows the following callouts e Gigabit Ethernet port 4 e LNK ACT LED which provides the following information 2 Status Description Off No Ethernet link on the port Green An Ether
17. eight 25 4 cm 10 inches Width 60 96 cm 24 inches Depth 55 88 cm 22 inches Weight 8 62 kg 19 Ib Environmental Table B 2 Environmental Specifications Item Specification Temperature Operating 0 to 40 C 32 to 104 F Storage 0 to 50 C 32 to 122 F Humidity 5 to 95 non condensing Altitude Up to 10 000 feet 3048 m Specifications B 1 v1 0 May 2007 WFS709TP ProSafe Smart Wireless Switch Hardware Installation Guide Operational Table B 3 Operational Specifications Item Specification Power Consumption 170 Watts maximum AC Input Voltage 90 132VAC 180 264VAC auto sensing AC Input Current 4A 110VAC AC Input Frequency 47 63 Hz Output Voltage 48VDC 802 3af maximum aggregate power draw for PoE is 100 Watts Standards IEEE 802 1x IEEE 802 3 10BASE T IEEE 802 3u 100BASE TX IEEE 802 3ab 1000BASE T B 2 Specifications v1 0 May 2007 Appendix C Related Documents This appendix provides links to reference documents you can use to gain a more complete understanding of the technologies used in your NETGEAR product Document Link Internet Networking and TCP IP Addressing Wireless Communications Preparing a Computer for Network Access Glossary http documentation netgear com reference enu tcpip index htm http documentation netgear com reference enu wireless index htm http documentation netgear com reference enu wsdh
18. ements and are 50 labeled with the EFUP 50 label shown at the left Hazardous Materials Declaration O X8 HR En Eia ET ER Pees REST 11363 20067 itk be 3958 ELE F The component does not contain this hazardous subelance above the maximum concentration values in homogeneous materials ified in the SJ T11363 2006 Industry Standard X Sors xvtgps teriw a trim titsJTI11383 200645 AE te EF egg This component does contain thie hazardous substance above the maximum concentration values in homogeneous materials specified in the SJ T11363 2006 Industry Standard uit s qu on ds dex gor Meta Pr di TRE GLA IR 4609 ud This table shows where these substances may be found in the supply chain of electronic information products as of the date of sale of the enclosed product kint ARRE a i A MRE KAS MIAH TA WIRMS spi oT EIR Vs fr UP AL JESHIS MUR PA EGRE a IF MPREIDEMS IF TI The Environment Friendly Use Period EFUP for all enclosed products and their parts are per the symbol shown here The Environment Friendly Use Period is valid only when the product is operated under the conditions defined in the product manual v1 0 May 2007 Product and Publication Details Model Number Publication Date Product Family Product Name Home or Business Product Language Publication Part Number Publication Version Number WFS709TP May 2007 Wireless WFS709TP ProSafe Smart Wireless Switch Business English 202 10264 01 1 0 v
19. ength for FE cables is 100 meters 325 feet Cables that run through plenums or air handling spaces as described in NEC 2002 Article 300 22 C should be suitable under NEC Article 800 50 and marked accordingly for use in plenums and air handling spaces with regard to smoke propagation such as CL2 P CL3 P MPP or CMP m Note Be sure to install cables in accordance with all applicable local regulations and ZEE practices GE Uplink Port 1000BASE T Copper GE Cable Table A 1 lists the cable characteristics for the 1000BASE T GE uplink port Table A 1 Copper GE Cable Characteristics Item Specification Cable Category 5 UTP Connector RJ 45 Range Up to 100 m 325 feet A 2 Cables and Connector Pinouts v1 0 May 2007 WFS709TP ProSafe Smart Wireless Switch Hardware Installation Guide Serial Console Port The serial console port is located on the front panel of the WFS709TP This port is for connecting a local management console and can be used to access the text based command line interface CLD to configure manage and troubleshoot the switch Warning Do not connect access points to the serial console port The serial port is A designed to connect to RS 232 only devices Non RS 232 devices such as APs will cause the WFS709TP to fail and can cause damage Port and Adapter Pinouts The serial console port s RJ 45 female connector accepts an RS 232 serial
20. er input socket on the chassis rear panel accepts a power cord with a standard IEC320 connector For proper safety and performance the power cord must be rated to 10 A and must conform to grounded electrical standards in the country in which the switch operates Task Overview As with any full featured network equipment deployment may involve multiple components as well as various individuals in your organization As the network manager you should become familiar with the components and deployment summary outlined in the following sections NETGEAR Smart Wireless Components Familiarize yourself with these three major components e WFS709TP Switch This is an enterprise class switch into which multiple access points APs are connected and controlled NETGEAR Wireless Access Points designed for small and mid sized businesses with enterprise class features can function as either access points or air monitors 1 6 Introduction v1 0 May 2007 WFS709TP ProSafe Smart Wireless Switch Hardware Installation Guide Wireless Access Point The NETGEAR WAGL102 and WGL102 are designed for this solution and provide the best features and easiest integration Several other NETGEAR access point products can be repurposed to work with the WFS709TP Refer to the NETGEAR support site for a list of which NETGEAR APs can be repurposed and for instructions on how to do so For full instructions on changing the switch s default values refer to the W
21. f contents or index to navigate directly to where the topic is described in the manual A Fi button to access the full NETGEAR Inc online knowledge base for the product model e Links to PDF versions of the full manual and individual chapters How to Print this Manual To print this manual choose one of the following options Printing a Page from HTML Each page in the HTML version of the manual is dedicated to a major topic Select File gt Print from the browser menu to print the page contents v1 0 May 2007 WFS709TP ProSafe Smart Wireless Switch Hardware Installation Guide Printing from PDF Your computer must have the free Adobe Acrobat reader installed in order to view and print PDF files The Acrobat reader is available on the Adobe website at http www adobe com Printing a PDF Chapter Use the PDF of This Chapter link at the top left of any page Click the PDF of This Chapter link at the top left of any page in the chapter you want to print The PDF version of the chapter you were viewing opens in a browser window e Click the print icon in the upper left of your browser window Printing a PDF version of the Complete Manual Use the Complete PDF Manual link at the top left of any page Click the Complete PDF Manual link at the top left of any page in the manual The PDF version of the complete manual opens in a browser window e Click the print icon in the upper left of your browser windo
22. i v1 0 May 2007 Contents About This Manual Conventions Formats and Scope cccceccssseceeseseneeeeeceeeaeeeeseeeaeeeesseetaeeeeeeseteeeeeeeeaaes ix Rowo Use TAS Manual siii tec emet ELO a asse cuc Rn ap IE E X How to Pup tis Mandela usesoocs e prier ud CREER DE E pa Epub pO a ER DOE EN PD UR X pice INW IAP SE E E UU xi Chapter 1 Introduction WFS709TP ProSafe Smart Wireless Switch Overview eesesesseeeeeee 1 1 Fron amd Rear Vie assiscueduien iis dei anda pe e bb edi a pM E Er ag a MU ORE EN DE RP CARE 1 2 iniu indicator LEDE ec ins R 1 2 Fast EUIS PASE i esatto iesu HRei unaEE dpi nM EEES 1 3 Eae M dcl TRETEN S UU T 1 5 Sond Console POL uisi cU iue nssdditstsetie sind daeuinedeutaM Ric n aden SUMMAE 1 5 Pans Heat EXeUSE iei ed cl e bea eoa dca or eeu i o d ER aS 1 6 Rack Mouning Brackolg si econu oet dese ctp riot d corner Se ctum io tam Lese ope ioo 1 6 Power Input OGRE cesariana eee ce ROO pussy pase lpd Au Resp IR Md PRINS RAM RD OPEN 1 6 Bi CIID RR 1 6 NETGEAR Smart Wireless Components sess 1 6 ESRI VTA enl Rm H eee 1 7 Chapter 2 Installing the Chassis Pre heialation TIN asco unu irat Ep ease Eu enarrat dolia o RA RIEN RR dd 2 1 ui MD T NT TY E eee E A PE TAE AE ENT T TO 2 2 iia HII MEE T E a E S S 2 3 Mounting DE I t T E 2 4 arce irs PON c NITE E 2 6 ASAE Mme 05561 15 ott aS 2 7 vii v1 0
23. net link has been established on the port but no data is currently being transmitted or received Flashing Green The port is transmitting or receiving data The flashing rate is proportional to your network activity SQ 7 uio Jk dl a Figure 1 3 See GE Uplink Port on page A 2 for cable specifications EE Note The Gigabit interface is not user replaceable Do not remove the port cover plate Serial Console Port Use this port to connect a local management console This connection can be used to access the text based command line interface CLI for initial configuration of the WFS709TP Introduction 1 5 v1 0 May 2007 WFS709TP ProSafe Smart Wireless Switch Hardware Installation Guide The port accepts an RS 232 serial cable with an RJ 45 male connector See Serial Console Port on page A 3 for more port and cable specifications Fans Heat Exhaust Three independent fans located on the side of the chassis promote proper air circulation for cooling the WFS709TP ProSafe Smart Wireless Switch During operation the air vents on the left and right sides of the chassis must remain unobstructed by cables or mounting equipment For proper air circulation leave at least 10 cm 4 inches of clearance on the left and right of the chassis Rack Mounting Brackets Mounting brackets are attached to each side of the chassis Power Input Socket 7 The pow
24. nouts The RJ 45 female connector pinouts are shown in Figure A 1 10 100 Mbps RJ 45 Female Ethernet Pin Out 1 ETH Rx POE negative fitm Rx POE negative LNK a J 3 ETH Tx POE positive At 4 Serial TxD POE positive 5 Serial TGND POE positive Bw ns ETH Tx POE positive pe 7 Serial RxD POE negative 8 Serial RGND POE negative Direction Input POE optional Output Serial optional Figure A 1 Cables The type of cable required for each port depends on the device being connected Note Refer to the document nstallation Guide ProSafe Wireless Access Point for information about specific power requirements Direct connection to a POE compatible device This requires a 4 or 8 conductor Category 5 UTP Ethernet cable with an RJ 45 male connector A straight through cable is required to preserve POE voltage polarity Cables and Connector Pinouts A 1 v1 0 May 2007 WFS709TP ProSafe Smart Wireless Switch Hardware Installation Guide For PoE the port should be connected directly to the intended device with no intervening hubs routers switches or other network equipment Connection to a regular 10 100 Mbps Ethernet segment This requires a 4 or 8 conductor Category 5 UTP Ethernet cable with an RJ 45 male connector The port detects MDI MDX and automatically adjusts for straight through or crossover cables The maximum l
25. on Guide Fast Ethernet Ports 2 Use the network to connect access points APs as well as wired LAN segments The ports provide 10 100 Mbps Fast Ethernet FE connectivity and can provide power and serial connectivity to compatible devices Power over Ethernet Each FE port supports IEEE 802 3af Power over Ethernet PoE When a compatible POE device such as the NETGEAR WAGL102 or WGL102 access point is connected to a network port the port can provide operating power to that device through the connected Ethernet cable This allows APs to be installed in areas where electrical outlets are unavailable undesirable or not permitted such as in the plenum and air handling spaces The network ports automatically detect when compatible PoE devices are connected and require power Special cables and adapters may be necessary to use PoE features with some equipment See Appendix A Cables and Connector Pinouts for port and cable specifications Port and LED Locations Figure 1 2 shows the FE ports and the location of the port LEDs ACCESS ACCESS POINT POINT STATUS STATUS oQ 4 WM oe VH poe 1 pe 7 20 jeg 3 9 0 1 z 3 4 5 6 7 Figure 1 2 FE Network Ports The eight FE ports are split into two four port blocks and numbered 0 through 7 Each FE port has three informational multi color LEDs These LEDs are LNK ACT amp POE ACCESS POINT STATUS Introduction 1 3 v1 0 M
26. r by the applicable National regulatory authority v1 0 May 2007 NOTE This product s firmware limits operation to only the channels allowed in a particular Region or Country Therefore all options described in this user s guide may not be available in your version of the product United States FCC Class A This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their own expense Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment This product is UL Listed UL60950 Canada This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the interference causing equipment standard entitled Digital Apparatus ICES 003 of the Department of Communications Cet appareil num rique respecte les limite
27. s de bruits radio lectriques applicables aux appareils num riques de Classe A prescrites dans la norme sur le mat riel brouilleur Appareils Num riques NMB 003 dict e par le minist re des Communications This product complies with CAN CSA C22 2 No 60950 standards Europe The WFS709TP ProSafe Smart Wireless Switch is compliant with the following EU Council Directives 89 336 EEC and LVD 73 23 EEC Compliance is verified by testing to the following standards EN55022 Class A EN55024 and EN60950 Warning This is a Class A product In a domestic environment this product may cause radio interference A in which case the user may be required to take adequate measures Japan This equipment is in the Class A category information equipment to be used in commercial and or industrial areas and conforms to the standards set by the Voluntary Control Council for Interference by Data Processing Equipment and Electronic Office Machines that are aimed at preventing radio interference in commercial and or industrial areas Consequently when this equipment is used in a residential area or in an adjacent area thereto radio interference may be caused to equipment such as radios and TV receivers iii v1 0 May 2007 VCCI Class A CORB ARER SERRE AERES VCCI DOSE IEDC 7 2 7 ARR i IE CT CORB RERR CERT 25 CBM WEBER TTZ ESNE COBRA AS87 EHE SEDBREINSTEMHBIVET Korea Class A xol Ad 7171 0 7 17 2 9j2 o2 Arla At
28. t IP addresses GUI screen text Fixed Command prompt CLI text code italic URL links e Formats This manual uses the following formats to highlight special messages Note This format is used to highlight information of importance or special interest Tip This format is used to highlight a procedure that will save time or resources Warning Ignoring this type of note may result in a malfunction or damage to the equipment v1 0 May 2007 WFS709TP ProSafe Smart Wireless Switch Hardware Installation Guide A Danger This is a safety warning Failure to take heed of this notice may result in personal injury or death e Scope This manual is written for the WFS709TP according to these specifications Product Version WFS709TP ProSafe Smart Wireless Switch Manual Publication Date May 2007 For more information about network wireless and firewall technologies see the links to the NETGEAR website in Appendix C Related Documents Note Product updates are available on the NETGEAR Inc website at http www netgear com support gt How to Use This Manual The HTML version of this manual includes the following Buttons gt and lt for browsing forwards or backwards through the manual one page at a time A button that displays the table of contents and an button Double click on a link in the table o
29. the left and right of the chassis Leave additional space in front and back of the chassis to access power cords network cables and indicator LEDs Limited electromagnetic interference Installing the Chassis 2 3 v1 0 May 2007 WFS709TP ProSafe Smart Wireless Switch Hardware Installation Guide For best operation keep the WFS709TP and all cords and cables at least 0 7 meters 2 feet from fluorescent lighting fixtures and 2 meters 6 feet from photocopiers radio transmitters electric generators and other sources of strong electromagnetic interference See also Appendix B Specifications Mounting the Chassis This section provides instructions for installing the WFS709TP ProSafe Smart Wireless Switch 1 Make sure that your rack environment meets the installation requirements listed on page 2 3 2 Attach the WFS709TP to the rack as described in the following section A Warning To avoid personal injury or damage to equipment get help in lifting and positioning the WFS709TP Also do not install the WFS709TP where instability or uneven mechanical loading may occur Note For proper operation make sure your rack environment is in compliance with the operating temperatures described in Appendix B Specifications e Position the chassis in the equipment rack and align the brackets mounting holes with the corresponding holes in your rack frame Figure 2 1 on page 2 5
30. uctive material before working with this product Never insert foreign objects into the chassis or any other component even when the WFS709TP is unpowered or unplugged Main power is fully disconnected from the WFS709TP by unplugging the power cord from the power outlet For safety reasons verify that the power outlet and plug are within easy reach of the operator Do not handle electrical cables which are not insulated This includes any network cables To minimize electrical hazard keep water and other fluids away from the product Comply with electrical grounding standards during all phases of installation and operation of the product Do not allow theWFS709TP chassis network ports power source or mounting brackets to contact any device cable object or person attached to a different electrical ground Also never connect the device to external storm grounding sources Installation or removal of the chassis must be performed in a static free environment The proper use of anti static body straps and mats is strongly recommended Do not ship or store this product near strong electromagnetic electrostatic magnetic or radioactive fields Do not disassemble the chassis This product has no internal serviceable parts When service or repair is needed see Technical Support on page ii 2 2 Installing the Chassis v1 0 May 2007 WFS709TP ProSafe Smart Wireless Switch Hardware Installation Guide Requirements
31. w gt Tip If your printer supports printing two pages on a single sheet of paper you can md save paper and printer ink by selecting this feature Revision History Part Number version Date Description Number 202 10264 01 1 0 May 2007 Initial NETGEAR release xi v1 0 May 2007 WFS709TP ProSafe Smart Wireless Switch Hardware Installation Guide Xii v1 0 May 2007 Chapter 1 Introduction The WFS709TP ProSafe Smart Wireless Switch is a full featured wireless switch that centrally manages NETGEAR access points delivering integrated wireless mobility security and converged services for both wired and wireless users This chapter contains the following topics e WFS709TP ProSafe Smart Wireless Switch Overview e Front and Rear View e Task Overview Once you are familiar with the system you can begin the installation process described in the next chapter WFS709TP ProSafe Smart Wireless Switch Overview The following list identifies the key features of the WFS709TP ProSafe Smart Wireless Switch e Supports up to 16 access points e Eight 10 100 Mbps Fast Ethernet FE ports with Power over Ethernet PoE capability One Gigabit Ethernet GE uplink port e One serial console port e Built in RF planning tool e Wireless Intrusion Detection and Protection e Advanced security features such as 802 1x support for EAP PEAP EAP TLS EAP TTLS 802 111
Download Pdf Manuals
Related Search