Ultra Start 42xx Automobile Alarm User Manual
Contents
1. INSTALL GUIDE Covers All 42xx and 43xx Series Remote Starter Alarms REMOTE STARTERS CAR ALARMS WWW_ ULTRASTARTERS COM Technical Support 866 698 5872 ext 0 Support ultrastarters com Note Some features may not be available on certain models ATTENTION The system must be placed into Service Mode before any service work is started on the vehicle It is the sole responsibility of the vehicle owner to ensure that this is done The manufacturer accepts no liability or responsibility for accidental starting of the vehicle CARBON MONOXIDE Never Start in an Enclosed Building Garage Carport etc The Hood Pin Safety Switch Must Always be Installed INSTALLATION MANUAL 2WAY REMOTE STARTERIALARM Page 2 Table of Contents Table of Contents Page 2 Pre Installation Page 3 Components Feature List Pre Installation Installation Procedures Page 4 Wiring Diagrams Page 5 7 Wire Description Page 8 9 6 Pin Connector Auxiliary Connectors Optional Connectors Jumper Positions Quick Start Installation Page 10 Basic Installation Plug in The Module Manual Transmission Vehicles Page 11 Additional Connections Clutch Bypass Important Tach Notes Page 12 13 Auto Tach Learn Quick Tach Learn Program Overview and Quick View Programming Page 14 15 Entering Program Mode Quick View Programming System Reset Programming Menus Page 16 20 Program Menu 1 User Settings Program Menu 2 Additional Settings Progr2. Setting 2 confirmed 2 LED flashes Press amp Hold the Program Button until the appropriate of park light siren chirps then release Press amp Release the Program Button to proceed to the next step Setting 3 Horn chirp Timing 14 pin auxiliary connector pin 5 1 5 ms Pulse Output 1 Flash chirp Short Quiet Horn Output Pulses 2 15ms Pulse Output 2 Flashes chirps Long Loud Horn Output Pulses 3 10 ms Pulse Output 3 Flashes chirps Normal Medium Horn Output Pulses Press amp Release the Program Button 3 Times Setting 3 confirmed 3 LED flashes Press amp Hold the Program Button until the appropriate of park light siren chirps then release Press amp Release the Program Button to proceed to the next step Default Settings INSTALLATION MANUAL 2WAY REMOTE STARTER ALARM Page 18 Menu 2 Additional Settings continued from previous page Setting 4 Button 4 Programmable 1 Trunk Release 1 Flash chirp Holding button 4 will activate Trunk Release 2 Garage Door 2 Flashes chirps Activates optional Garage Door Interface 3 Car Finder 3 Flashes chirps Holding Button 4 activates Car Finder Setting 5 Siren Horn Automatic transmission only 1 Horn Output 1 Flash chirp Pulsed output for horn activation 2 Siren output 2 Flashes chirps Constant output for siren activation Press amp Release the Program Button 5 Times Setting 5 confirmed 5 LED flashes Press amp Hold the Program Button until the appropriate of pa
3. 12V ToT 87 87 i Green 87a 87a 86 9 a 86 85 Blue 30 30 IS Lock x To Vacuum Un Pump lock Cut Note When installing relays always use a fused power source INSTALLATION MANUAL 2WAY REMOTE STARTER ALARM Page 24 DIAGNOSTICS If the remote starter does not activate when the start button is pressed the park lights will flash a diagnostic to indicate what shutdown input has been triggered For example when the start button is pressed the park lights flash 3 times slowly Looking at the chart below this would indicate that the system is in Service Mode simply follow the instructions listed in the owners manual on exiting Service Mode and the remote starter will begin to function as normal PARK LIGHTS STATUS LED DIAGNOSTIC CODE 3 Flashes Series of 3 Flashes Door Opened M Models 3 Slow Flashes LED s On Solid system Is In Service Mode 4 Slow Flashes series of 4 Flashes Not in Reservation Mode M units 5 Flashes series of 5 Flashes Hood Pin Opened 5 Slow Flashes series of 5 Flashes Ignition On During Start Attempt 6 Flashes series of 6 Flashes Brake Pedal Shutdown Flashes series of 7 Flashes Tach Lock Out DIAGNOSTIC MEMORY LED Flashes Diagnostic 5 Flashes The system was shutdown by the brake switch input 6 Flashes The system was shutdown by the hood pin input 7 Flashes The system did not detect the tach signal 8 Flashes The system made 3 start attempts without starting Being that the installer does not alway
4. 15 Quick View Programming See the following pages for more detailed programming instructions Menu 1 Press Lock 1 Flash 2 Flashes 3 Flashes 1 Ignition Lock Enabled Lock Only Disabled 2 Siren Chirp Type 1 Type 2 All Chirps 3 Lock amp Unlock Options Double Unlock 3 second 5 second 4 Unlock Disarm 125ms 750ms 5 Passive Locks Enable Disable 6 Shock Sensor Disable Enable T Passive Arming Type 1 Type 2 Disable CAPET AVATI O Y e T 3 Flashees 1 Secure Service Mode 15 seconds 5 seconds 2 Park Light Output 30 seconds Park Light Light Flash 3 Horn Timing Ooms 50ms 10ms 4 Button 4 Programmable Trunk Release Garage Door Car Finder 5 Reservation Mode Manual Auto Reservation Menu 3 Press Start 1Flash_ 2 Flashes 3 Flashes 1 Lock Unlock Type Type 1 Type 2 Normal 2 Gas Diesel Negative 15 second Gas Positive 3 Rearm Output Type 1 Type 2 Rearm 4 Run Time 4 Min 45 Min 15 Min 5 Crank Time 10 seconds 3 seconds 5 seconds 6 Starter Disable GWR Active Passive GWR Safety Start Mode Press twice Press once Mena pessi Fah PF SFE 1 Low Idle Learn Low Idle Learn 2 Adjust For Over Crank Reduced by 10 3 Adjust For under Crank Increased by 10 Bold type indicates settings that are Factory Default System Reset The system reset will clear any changes made to the Program Menu s as well as the Tach setting When the system reset is complete the system must be Tach learned before the remote starter will operate 1 Turn the ignition key f
5. 7 Times Setting 7 Confirmed with 7 LED flashes Press amp Hold the Program Button until the appropriate of park lights siren chirps then release Press amp Release the Program Button to proceed to the next step Menu 2 Additional Settings DB te f ignition ON OFF ON OFF ON Press and Press ano Press amp Release Program Button Ignition 3x Press and Program Switch Program Switch On Off Release Press button 1x Settina 1 Onti Press Button 2 Unlock On Off On the Program 2 to enter s E 2 ate Button Program 3x Setting 3 3x Option 3 Menu 2 Setting 1 Secure Valet Mode Length of time required to set the system into Service Mode 1 Secure Valet 1 Flash chirp Hold the Program Button for 15 seconds 2 Normal Valet 2 Flashes chirps Hold the Program Button for 5 seconds Press amp Release the Program Button 1 Time Setting 1 confirmed 1 LED flashes Press amp Hold the Program Button until the appropriate of park light sirenchirps then release Press amp Release the Program Button to proceed to the next step Setting 2 Parking Light Trunk Output 14 pin auxiliary connector pins 2 amp 8 1 30 sec Output 1 Flash chirp Park Lights on for 30 seconds when Unlock is pressed 2 Negative Park Lights 2 Flashes chirps Switches the Park Lights Trunk Outputs 3 Park Lights 3 Flashes chirps 2 Park Light Flashes when Unlock is pressed Press amp Release the Program Button 2 Times
6. Press Button 4 On Off Release the Release the Hold the On Off On Program oo Program Switch Program Switch Button Program 1x Setting 1 1x Option 1 Menu 4 2X Setting 2 2X Option 2 3x Setting 3 3x Option 3 Setting 1 Auto Tach Learn 1 Perform a System Reset See page 15 2 Turn the ignition key on Park lights will turn on 3 Start the vehicle the LEDs on the antenna will come on when a proper tach signal is detected 4 After approximately 30 35 seconds the park lights will go out then will flash twice and the siren will chiro twice to confirm that a tach signal has been learned If the LEDs do not come on a proper signal is not detected Try a different tach source and follow steps 1 thru 4 Setting 2 Over Crank Adjustment 1 Enter Program Mode turn ignition ON OFF ON OFF ON press and release the Program Button 2 Press and release the button on the remote 3 Press and release the Program Button twice LEDs will flash 2 times consecutively 4 Press and hold the Program Button The park lights flash and the siren will chiro one time Each time the park lights flash and the siren chirps the setting is reduced 5 Release the Program Button Exit Program Mode and test remote starter Setting 3 Under Crank Adjustment 1 Enter Program Mode turn ignition ON OFF ON OFF ON press and release the Program Button 2 Press and release the button on the remote 3 Press and release the Program Button
7. the Program Button until the appropriate of park lights siren chirps then release Press amp Release the Program Button to proceed to the next step Setting 6 Anti Grind Starter Kill Auxiliary Connector Pin 4 1 Active 1 Flash chirp when locked and during remote start Anti Grind 2 Passive 2 Flashes chirps when locked 30 seconds after ignition is Off or unlock is pressed 3 Anti grind 3Flashes chirps Output during remote start only Anti grind Bypass module Press amp Release the Program Button 6 Times Setting 6 Confirmed with 6 LED flashes Press amp Hold the Program Button until the appropriate of park lights siren chirps then release Press amp Release the Program Button to proceed to the next step Setting 7 Safety Start 1 Safety On 1 Flash chirp Press the start button twice within 3seconds to remote start vehicle 2 Safety Off 2 Flashes chirps Press the start button once to remote start vehicle Press amp Release the Program Button 7 Times Setting 7 Confirmed with 4 LED flashes Press amp Hold the Program Button until the appropriate of park lights siren chirps then release Press amp Release the Program Button to proceed to the next step Default Settings INSTALLATION MANUAL 2WAY REMOTE STARTER ALARM Page 20 Menu 4 Tach Settings o r Ignition ON OFF ON OFF ON oP i Press amp Release Program Button Ignition 3x Press and NS Press and Press and
8. the remote starter 500ma Output Door lock output Door lock module output only 500ma Output Door unlock output Status Led s ACTIVE RF ANTENNA N Program Button r The antenna MUST be connected for the system to operate Temperature Sensor LT Models Only Input Trigger To Start 1350 Series CHD Not available on 1250 Series 250ma Output When Running VV hite Violet Low Current Output Low Current Output Output on White wire Jumper position second Starter Position 1 second Accessory Position 2 Second Ignition Position 3 The jumpers control the output from the WHITE wire on the 6 pin harness This is an 30amp relayed output Place the jumpers in the following order to change the output If the jumper is in position 1 the output on the white wire will be 2nd Starter If the jumper is in position 2 the output on the white wire will be 2nd Accessory If the jumper is in position 3 the output on the white wire will be 2nd Ignition The factory default setting of the selectable output jumper is position 3 INSTALLATION MANUAL 2WAY REMOTE STARTERIALARM Page 8 6 Pin Power Connector 6 pin Description Test For Wire 1 Yellow 30amp Starter Output This wire will test Ovolts in off accessory and in the ignition position 12volts during start only 2 Green 30amp Heat Acc Output This wire will test Ovolts in the off position 12 14
9. three times LEDs will flash 3 times consecutively 4 Press and hold the Program Button The park lights will flash and the siren will chirp one time each time the park lights flash and the siren chirps the setting is increased 5 Release the Program Button Exit Program Mode and test remote starter Repeat steps 1 5 if necessary 2WAY REMOTE STARTER ALAM INSTALLATION MANUAL Page 21 Transmitter Programming Step 1 Within 3 seconds turn the ignition ON OFF ON OFF ON Leaving Key ON Step 2 Press and hold the Program Button The park lights will turn ON and the siren will chirp once Continue to hold the Program Button the park lights will turn off and the siren will chiro 5 times quickly Step 3 While holding the Program Button press the LOCK button on each of the remote s to be programmed lf remote s are being programmed for 2nd Car Operation press the button on each of the 2nd car remote s to be programmed Note The park lights will flash once and the siren will chiro once each time a new code is learned Note Transmitter programming must done quickly Do not pause more than one second between each transmitter All the transmitters to be used must be programmed at the same time All transmitters not programmed at this time will be erased from memory for security The system holds a maximum of 4 transmitter codes including 2nd car remote codes If the Park Lights do not turn ON turn ignition OFF wait 5 secon
10. 1 or 14 pin connectors Setting 3 Rearm Output Auxiliary Connector Pin 1 1 Type 1 1 Flash chirp Pulse after start and with lock Provides Lock Pulse 2 Type 2 2 Flashes chirps Pulse after start only Provides Lock Pulse 3 Factory Re arm 3 Flashes chirps Pulse with lock and after starter shutdown Press amp Release the Program Button 3 Times Setting 3 Confirmed with 3 LED flashes Press amp Hold the Program Button until the appropriate of park lights siren chirps then release Press amp Release the Program Button to proceed to the next step Setting 4 Run Time 1 4 Minutes 1 Flash chirp Runs for approximately 4 minutes when activated 2 45 Minutes 2 Flashes chirps Runs for approximately 45 minutes when activated 3 15 Minutes 3 Flashes chirps Runs for approximately 15 minutes when activated Press amp Release the Program Button 4 Times Setting 4 Confirmed with 4 LED flashes Press amp Hold the Program Button until the appropriate of park lights siren chirps then release Press amp Release the Program Button to proceed to the next step Setting 5 Maximum Crank Time 1 10 Seconds 1 Flash chirp 10 sec max time that the starter will stay engaged 2 3 Seconds 2 Flashes chirps 3 sec max time that the starter will stay engaged 3 5 Seconds 3 Flashes chirps 5 sec max time that the starter will stay engaged Press amp Release the Program Button 5 Times Setting 5 Confirmed with 5 LED flashes Press amp Hold
11. 2 With 11 pin Connector Gas Diesel Mode Auxiliary Connector Pin 12 1 Input 1 Flash chirp Glow Plug input Waits maximum 30 seconds then starts 2 Time Delay 2 Flashes chirps Waits for approximately 15 seconds then remote starts 3 Gas Input 3 Flashes chirps Waits 2 seconds to start if no diesel input is detected Press amp Release the Program Button 2 Times Setting 2 Confirmed with 2 LED flashes Press amp Hold the Program Button until the appropriate of park lights siren chirps then release Press amp Release the Program Button to proceed to the next step Note Setting 2 will vary depending on the board layout 11 or 14 pin connectors Default Settings 2WAY REMOTE STARTER ALARM INSTALLATION MANUAL Menu 3 Starter Settings Continued From Previous Page Page 19 Setting 2 With 14pin Connector Gas Diesel Mode Auxiliary Connector Pin 12 1 Input 1 Flash chirp Glow Plug input Waits maximum 30 seconds then starts 2 Time Delay 2 Flashes chirps Waits for approximately 15 seconds then remote starts 3 Gas Input 3 Flashes chirps Waits 2 seconds to start if no diesel input is detected Press amp Release the Program Button 2 Times Setting 2 Confirmed with 2 LED flashes Press amp Hold the Program Button until the appropriate of park lights siren chirps then release Press amp Release the Program Button to proceed to the next step Note Setting 2 will vary depending on the board layout 1
12. Program Button until the appropriate of park lights siren chirps then release Press amp Release the Program Button to proceed to the next step Setting 5 Active Passive Locks 1 No Auto Lock with Passive Arm 1 Flash Chirp Doors do not auto lock with passive arming 2 Doors Auto Lock with Passive Arm 2Flashes Chirps Doors Lock when passive arming Press amp Release the Program Button 5 Times Setting 5 Confirmed with 5 LED flashes Press amp Hold the Program Button until the appropriate of park lights siren chirps then release Press amp Release the Program Button to proceed to the next step Default Settings OWAY REMOTE STARTER ALARM INSTALLATION MANUAL i Page 17 Menu 1 User Settings continued from previous page Setting 6 Sensor Enable Disable 1 Sensor Disabled 1 Flash Chirp Impact Sensor Disabled 2 Sensor Enabled 2 Flashes Chirps Impact Sensor Enabled Press amp Release the Program Button 6 Times Setting 6 Confirmed with 6 LED flashes Press amp Hold the Program Button until the appropriate of park lights siren chirps then release Press amp Release the Program Button to proceed to the next step Setting 7 Passive Active Arming 1 Passive Arming 1 Flash chirp Auto Arms 30 seconds after last door is closed 2 Active Arming with Rearm 2 Flashes chirps If unlock is pressed and no door is opened 3 Active Arming 3 Flashes chirps Arms with remote transmitter only Press amp Release the Program Button
13. Release the Program Button to proceed to the next step Setting 2 Siren Chirp Settings Auxiliary Connector Pin 5 1 Lock amp Unlock chirps Disable 1 Flash Chirp Chirps for Panic Car Finder Only 2 Lock amp Unlock chirps Enable 2 Flashes Chirps Chirps for Lock Unlock Panic Car Finder Only 3 All Chirps Enable 3 Flashes Chirps Chirps for all features Press amp Release the Program Button 2 Times Setting 2 Confirmed with 2 LED flashes Press amp Hold the Program Button until the appropriate of park lights sirenChirps then release Press amp Release the Program Button to proceed to the next step Setting 3 Door Lock Options 1 Double Unlock Pulse 1 Flash Chirp 15 Second lock amp 2 unlock pulses 2 3 Second Lock amp Unlock 2 Flashes Chirps 3 Second Lock amp Unlock Pulses 3 75 Sec Lock amp Unlock 3 Flashes Chirps 15 Second Lock amp Unlock Pulses Press amp Release the Program Button 3 Times Setting 3 Confirmed with 3 LED flashes Press amp Hold the Program Button until the appropriate of park lights siren chirps then release Press amp Release the Program Button to proceed to the next step Setting 4 Door Unlock amp Disarm Pulse Duration 1 Short Pulses 1 Flash Chirp 125ms pulses on Unlock amp Disarm outputs 2 Normal Pulses 2 Flashes Chirps 750ms pulses on Lock Unlock amp Disarm outputs Press amp Release the Program Button 4 Times Setting 4 Confirmed with 4 LED flashes Press amp Hold the
14. a few moments to walk around the vehicle looking for any damages and make note if any are found Also check other functions such as vehicle lighting system warning lights or check engine lights Check if the vehicle has a factory security or anti theft Transponder or PASS LOCK system These systems will require additional parts and labor to complete the installation Use of the proper tools and testing equipment is also very important Never use a grounding style test light to test for wires in the vehicle Use only a Circuit Safe test light or digital Volt Ohm Meter It is the sole responsibility of the installer to test and verify all connections Note This remote starter system is designed for fuel injected and diesel engines If the vehicle is a manual transmission a M series remote starter must be installed Any model number followed by the letter M is specially designed for manual transmission vehicles The M series remote starter will not work in an automatic transmission vehicle INSTALLATION MANUAL 2WAY REMOTE STARTER ALARM Page 4 Recommended Installation Procedures Proper Connections Remote Starters can handle loads of up to 30 amps for extended periods of time It is critical to insure that all high current connections are properly soldered and insulated with quality electrical tape Failing to insure proper connections will result in warranty being VOID and can result in damage to the vehicle and remote start
15. am Menu 3 Starter Settings Program Menu 4 Tach Settings Remote Transmitter Page 21 Ist amp 2nd Car Transmitter Programming Battery Replacement Relay Diagrams Page 22 23 Door Lock Diagrams Diagnostics Page 24 Diagnostics Chart Diagnostic Memory 2WAY REMOTE STARTER ALARM INSTALLATION MANUAL Page 3 Components Control module 2way LCD and 1way transmitters Antenna with built in 6 pin main harness with dual Program Button and LED s 30 amp power inputs Multi tone Siren 11 pin harness 14 pin harness 4 pin harness 3 pin keyless entry harness 2 pin Harness 4350 and LT Models Hood pin safety switch Installation and Owner Manuals 42xx series 43xx series Feature List Auto Tach learning with Quick Learn option Turbo Timer Mode Starter Kill Anti Grind Protection Engine Idle Mode Remote Panic Feature System Override Protection Programmable Wait to Start Dual Car Operation Service Mode Valet Park Light Diagnostics Active Passive Arming Program 4 Transmitter Codes Run Time 4 15 or 45 minutes Ignition Auto Lock Door Locks 125s 75s 3 0s Double Unlock Dual Stage Shock Sensor Cold Start With Four Start Intervals or Temp Mode LT Models Only Recommended Pre Installation Procedures Remote car starters and alarms should be professionally installed Review the installation and owner manuals and acquire a vehicle wiring diagram for the vehicle to be worked on Take
16. and the horn will chirp 2 times to confirm power up on automatic transmission models Manual transmission models will flash the park lights and siren 4 times to confirm power up 2WAY REMOTE STARTER ALARM INSTALLATION MANUAL Page 11 Manual Transmission M Models Never install an automatic transmission remote starter into a manual transmission vehicle Doing so may result in serious injury or death Do not install remote starters in convertible vehicles The following wires must be connected In addition to the basic remote starter installation Park Brake Input This wire is located at the park brake switch The wire will switch to when the park brake is applied Never connect the Black White wire straight to a ground Door Pin Input A negative door pin wire will be or neutral when the door is closed then switch to when the door is opened Always ensure that all the vehicles doors are sensed by this wire Door Pin Input A positive door pin wire will be or neutral when the door is closed then switch to when the door is opened Always ensure that all the vehicles doors are sensed by this wire If any Door Pin Switches or the Park Brake Switch is not working correctly DO NOT INSTALL UNTIL THE VEHICLE IS REPAIRED Clutch Bypass In most cases the clutch switch will need to bypassed during remote starting This is a temporary bypass the clutch switch should never be disconnected or al
17. ck Module Only 3 Blue Door Unlock Door Unlock Output Programmable Menu 1 Setting 3 The centre pin of the keyless entry harness is not to be used for anything besides plug in devices such as the VP 1 DL 3 DL 7 and Data Bus Modules Overloading this output will damage the remote starter 4 Pin Connector Blue RF Antenna Program Button Connector Remove the plastic from the adhesive tape and place the antenna in the center of the windshield behind the rear view mirror Run the cable behind the head liner and A pillar panels to the module under the dash The Antenna Must Be Connected Before the System will Operate 2 Pin Connector White Connector for Instant Start Input or Temperature Sensor on LT models Note This Input is not available on the 1250 Series 3 Pin Connector White 1 White Violet GWR Ground output while running This output can be used for bypass module activation or adding additional relays 2 Black Ground Low current constant ground output 3 Red 12volts Low current constant 12volt output INSTALLATION MANUAL 2WAY REMOTE STARTER ALARM Page 10 Step 1 Connect All Of the Following Wires 6 Pin Power Connector Yellow 30amp Starter Output 12volts during start position only Green 30amp Heater Output 12volts in the accessory position off during start and 12volts during run Red 30amp Power Input Constant 12volt power at ignition harness or battery Red 30amp Power Input Constant 12volt pow
18. ds and repeat steps 1 amp 2 Ignition 3x Press and On Off On Off On HOLD the Program Press and Press and Press and Press and Button Release Release Release Release Button 1 Button 1 Button 1 Button 1 Battery Replacement When the Battery Icon on the remote indicates that the battery is low the battery should be changed promptly Replace with quality 1 5volt AAA battery Negative Fila DENONA e yD Positive INSTALLATION MANUAL 2WAY REMOTE STARTERIALARM Page 22 Negative Type Door Locks 250ma Vehicle To Control Lock Unlock Relay or Actuators Switch Negative Door Locks More Than 250ma Vehicle Lock Unlock Id H Switch loc IS Lock ae ke E Positive Type Door Locks To Control Relay or Actuator Un Vehicle ince Lock Lock Unlock i Switch Note When installing relays always use a fused power source Fused 12V To Control Relay or Actuator OWAY REMOTE STARTER ALARM INSTALLATION MANUAL Page 23 5 Wire Reverse Polarity Type Door Locks I a Vehicle Lock Lock Unlock Lock Switch bale x OG Cut N Fused 12V 87 8 ToActuator Aftermarket Doorlock Actuators Fused 12V oen h s i Ne een 87a 87a To Lock Wire ii 30 30 of Actuator loll To Unlock Wire of Actuator Vacuum Type Door Locks Fused
19. ected then after 30 35 seconds the park lights will flash and the siren will chirp twice to confirm Tach Learn If the park lights do not turn on check for proper connection on the BLUE ignition wire at the 6 pin connector This wire should be connected to the vehicle main ignition wire and must not turn off during the start position If the ignition connection is good reset the system and repeat step 1 If the LEDs do not come on during tach learn a proper tach signal was not detected If not tach learned the system will flash the park lights seven times when the start button is pressed The system must be Tach Learned before remote starting Note If the park lights do not flash in auto tach learn mode it may be necessary to connect to a different tach source It is important the ignition output from the remote starter is connected to a wire that does not turn off in the crank position The remote starter will not tach learn if connected to the wrong wire For best results connect the tach wire to the coil pack or to a fuel injector wire New If the original Tach source is changed a system reset must be preformed before a new tach signal can be learned to the system This does not apply if the Quick Learn feature is being used See page 15 for system reset Your Basic Install Is Complete NOTES 1 If the vehicle does not start when the remote starter is activated check if the park lights are flashing a diagnostic code See d
20. er at ignition harness or battery Blue 30amp Ignition Output 12volts in the ignition start and when run positions White 30amp Select Output Selectable Output for vehicles that require 2nd Ign Acc or Starter wires See jumper diagram Note The white wire may not be required on all vehicles Auxiliary Connectors Black System Ground Input Connect to Chassis Ground White Park Light Output Connect to Park Light system Green Wht Hood Pin Input Connect to the Hood Pin Safety Switch Blue White Tach Connect To A C Tach Source Above 2volts AC Pink Brake Switch Connect To When Brakes Is Applied White Blue Siren Output Connect to Siren Horn Manual Transmission Connections M Models Only Black Wht Park Brake Input Connect to Park Brake wire Green Door Pin Input Connect to door pin when doors opened Purple Door Pin Input Connect to door pin when doors opened Note Connect only one of the door pin inputs If the vehicle has a positive door pin system connect the purple wire if negative connect the green wire Never install an automatic module into a manual transmission vehicle Step 2 Plug In The Module When all the connections are done the contro module can be plugged in Before connecting the contro module make sure the ignition is in the OFF position Plug in the 6 pin harness and the Auxiliary harness then any other connectors that were used The park lights will flash
21. er module The manufacturer is not responsible for any such damages It only takes a few more minutes to do the job right Under Hood Connections Route the hood pin and tach wire through the firewall into the engine compartment If possible route the wires through a factory rubber grommet If drilling a hole through the firewall BE CAREFUL Always check for obstructions on both sides of the firewall After drilling use a snap in grommet to protect the wires from sharp edges Use split loom to insulate the wires route the wires clear of moving parts and extreme heat The hood pin switch must always be installed and the tach wire should always be soldered and taped properly Installing the External Long Range Antenna To insure the best possible reception place the antenna in the center of the windshield below the tint screen and behind the rear view mirror Before attaching to the glass ensure that the surface is clean and dry Run the cable under the head liner and behind the A pillar panel Be careful not to pinch the antenna cable Plug the antenna into the BLUE connector on the Control Module Mounting The Control Module Never mount the module in the engine compartment Select a location under the dash to install the main module Be certain that the module is securely attached and does not obstruct any serviceable areas Do not force or jam the module into tight places instead of mounting The module must be free from all moving parts s
22. iagnostic chart 2 If the vehicle still does not start check all connections and check for factory Anti Theft system Note If the vehicle is not starting correctly it may be necessary to adjust the tach See page 13 for Quick Tach Learn OWAY REMOTE STARTER ALARM INSTALLATION MANUAL Page 13 Important Tach Notes Tach Learning the remote starter is one of the most important steps in the installation process Do not tach learn vehicle while the engine is in high idle To ensure the best possible tach setting ensure that the vehicle is at low idle normal operating RPM Vehicles such as Toyota and Honda may idle much higher when the engine is warm compared to starting the vehicle when the engine is cold The Quick Learn feature may be used to tach learn the vehicle again but at a normal engine RPM Quick learn Tach Start the j Press and release F vehicle with Hold the the program button Y the key brake pedal BRAKE then press and hold Quick Learn Tach is designed to re learn the remote starters tach setting while the vehicle is at normal idle RPM Vehicles such as Toyota and Honda will run at a very high idle for a number of minutes when first started If tach learned when the vehicle is at high Idle then remote started when the vehicle is cold The engine does not increase to the RPM that is was learned at The Following steps can be used to learn tach at a more suitable idle 1 Start the vehicle and leave running by the ign
23. ition key until the engine idles down 2 Press and hold the brake pedal 3 Press and release the Program Button Located on the antenna then press and hold 4 The park lights will flash to confirm Quick Learn Tach Note The remote starter must be Tach Learned before the Quick Tach Learn feature will operate TIP Manual Low Idle Learn While in the tach learning mode firmly apply the park brake then hold the brake pedal Place the transmission into reverse gear and wait for the park lights to flash confirming Tach Learn INSTALLATION MANUAL 2WAY REMOTE STARTER ALARM Page 14 Entering Program Mode 1 With the ignition in the OFF position turn the ignition key from Off to On 3 times ON OFF ON OFF ON within three seconds Leave the key in the ON position 2 Press and release the Program Button located on the antenna The park lights will flash and the siren will chirp to confirm entering program mode 3 Select desired Program Menu See below The park lights will flash and siren will chirp to confirm the selected menu 4 Select Programmable Setting a Press and release the Program Button the correct number of times to select the desired Program Setting The park lights and LEDs will flash and the siren will chirp to indicate the Program Setting that has been selected For example 1 flash chirp Program Setting 1 2 flashes chiros Program Setting 2 etc b Press and Hold the Program Button until the par
24. k lights flash and the horn optional chirps to confirm the desired setting For example 1 flash chirp Setting 1 2 tlashes chirps Setting 2 3 flashes chirps Setting 3 c Turning the ignition key to the Off position or 30 seconds of no activity will exit Program Mode This will be confirmed with a light flash and a long siren chirp The Program Menu may be changed at any time by pressing the transmitter button below this will allow the installer to jump from one menu then quickly jump to another menu and change another setting without re entering Program Mode Note f unit does not enter Program mode turn ignition off for 5 seconds and repeat steps 1 4 Ignition 3x On Off Hira and Press button Press button Press button Press button On OffOn Release 4 for Menu1 2forMenu2 3forMenu3 4 forMenu4 Program Menus Menu 1 User Settings Press Lock Button 1 Page 16 17 This program menu is for the adjustments for the user and door lock options Menu 2 Additional Settings Press Unlock Button 2 Page 17 18 This program menu is for additional settings Menu 3 Starter Settings Press Start Button 3 Page 18 19 This program menu is for various remote car starter applications Menu 4 Tach Settings Button 4 Page 20 This program menu is for tach signal adjustments 2WAY REMOTE STARTER ALARM INSTALLATION MANUAL Page
25. rk Brake Switch Connect switch that provides when the switch is applied 7 Purple Door Pin Input nout to detect open door Connect to door pin that switches to 12volts when the door opened 8 White Park Lights Output 70amp park light output Connect to circuit Ovolts when Parking Lights are off 12volts when park lights are on 9 Green White Hood Pin Input Negative input from hood pin safety switch Switch is grounded when the hood is opened Must be connected 10 Green Door Pin Input Input to detect open door Connect to door pin that switches to Negative when the door is opened 2WAY REMOTE STARTER ALARM INSTALLATION MANUAL Page 9 Auxiliary Connectors continued from previous page 11 Black Ground System Chassis Ground Input 12 Blue Glow Plug Diesel Glow plug input detects both 12volt and negative glow plug signals Programmable input See Menu 3 13 Blue White Tach A C Tach Signal Input Used to detect when the vehicle has started This wire is connected to the vehicles coil fuel injector or crank sensor wire 14 Pink Brake input Positive Brake Input Used to detect the brake switch being applied Found at the brake switch connector 15 Wht Violet GWR Output while remote starter is activated Used to activate Anti theft bypass modules adding 3rd ign etc 3 Pin Connector Red 1 Green Door Lock Door Lock Output Programmable Menu 1 Setting 3 2 Red 12volt Output Output For Door Lo
26. rk light sirne chirps then release Press amp Release the Program Button to proceed to the next step Setting 5 Reservation Mode M units only 1 Manual Reservation 1 Flash chirp Activate Reservation Mode by pressing Button 2 Auto Reservation 2 Flashes chirps Activate Reservation Mode by pressing brake Press amp Release the Program Button 5 Times Setting 5 confirmed 5 LED flashes Press amp Hold the Program Button until the appropriate of park light sirne chirps then release Press amp Release the Program Button to proceed to the next step oP WH Menu 3 Starter Settings fa oP Ignition ON OFF ON OFF ON Ignition 3x Press and Press and Press and Press amp Release Program Button nO Release th press buton aaae Sutch et ith Press Button 3 Start Site E AA Menu 3 2x Setting2 2x Option 2 3x Setting 3 3x Option 3 Setting 1 Special Door Lock Unlock Operations Factory Alarm Rearm 1 Type 1 1 Flash chirp Unlock pulse before start Lock pulse after start and on shutdown 2 Type 2 2 Flashes chirps Lock pulse ONLY after remote start shutdown 3 Type 3 3 Flashes chirps Default Lock Unlock Pulses Press amp Release the Program Button 1 Time Setting 1 Confirmed with 1 LED flashes Press amp Hold the Program Button until the appropriate of park lights siren chirps then release Press amp Release the Program Button to proceed to the next step Setting
27. rom Off to On 3 times ON OFF ON OFF ON within three seconds Leave the key in the ON position 2 Press and release the Program Button located on the antenna The park lights will turn on and the siren will chirp one time 3 Then press and hold the Program Button until the park lights flash and the siren will chirp 3 times slowly to confirm system reset System is now reset to factory defaults Note System Reset does not delete the transmitter codes from memory INSTALLATION MANUAL 2WAY REMOTE STARTER ALARM Page 16 Menu 1 User Settings a WP i a 7 Ignition 3x Press and Press and Press and Ignition ON OFF ON OFF ON On Off Release the Release the Hold the Press amp Release Program Button On Off On Program press button Program Switch Program Switch p Button 1 Lock Button 1 to enter 1x Setting 1 1x Option 1 ress Button 1 Lock Program Menu 1 2X Setting2 2x Option 2 3x Setting 3 3x Option 3 Setting 1 Ignition Auto Lock 1 Ignition Lock amp Unlock Enable 1 Flash Chirp Doors Lock Unlock with Ignition key 2 Ignition Lock Only 2 Flashes Chirps Doors Lock when ignition is turned ON only 3 Ignition Auto Lock Disable 3 Flashes Chirps Doors do not Lock Unlock with Ignition key Press amp Release the Program Button 1 Time Setting 1 Confirmed with 1 LED flash Press amp Hold the Program Button until the appropriate of park lights siren chirps then release Press amp
28. s see when the system shuts down or fails to start Diagnostic Memory will store in memory up to four shutdown codes This information can then be accessed to determine the source of the shutdown To Enter Diagnostic Mode Step 1 Turn the ignition on then turn off Press the Program Button and release Step 2 The system will respond with three park light flashes and the siren will chirp the same number of times as the events in memory Maximum four events four chirps NOTE Ifthe siren does not chirp there are no events in memory Step 3 Press the Program Button once to view the last shut down code The siren will chirp once to confirm code one If the horn does not chirp there are no codes in memory Step 4 The LEDs on the antenna will flash a code corresponding to a shut down trigger Press the Program Button again to check the second code The siren will chirp twice to confirm code two Step 5 To Clear Diagnostic Memory While in Diagnostic Mode press and hold the Program Button for five seconds The park lights will flash and the siren will chirp once NOTE Once diagnostic memory has 4 shutdown events in memory the system will not Record any further shutdown events until the system memory has been cleared
29. tered to not work as it is indented to As a Safety Switch The clutch switch is usually a 2 wire switch mounted directly to the clutch pedal There are several types of clutch switches that operate in one of the following ways Type 1 Starter Wire Bypass The starter wire travels form the key switch through the clutch switch to the starter motor Connect the Remote Starters Starter Output wire directly to the starter motor side of the clutch switch Type 2 Negative High Current This switch grounds the factory starter relay and allows the vehicle to start Connect a relay to ground the clutch switch wire when the remote starter is activated The starter wire is connected at the ignition switch Type 3 Connect Switch Install a relay to connect the two wires at the switch when the remote starter is activated The starter wire is connected at the ignition switch Type 4 Disconnect Switch Install a relay to disconnect one of the wires at the clutch switch The starter wire is connected at the ignition switch Testing for the correct wire is critical Never connect to a circuit if you are not sure of it s operation Contact your dealer or technical support for more information INSTALLATION MANUAL 2WAY REMOTE STARTER ALARM Page 12 Auto Tach Learn 1 Turn the ignition key to the ON position The park lights will turn on 2 Start the vehicle with the key The LEDs on the antenna will turn on if a proper tach signal is det
30. uch as brake clutch and gas pedal linkages Do not place the module directly in front of a heater vent Testing The System When the installation is complete it will be necessary to test that the system is working correctly The system s default programming will work on the majority of vehicles but might need to be adjusted for some applications If the installation requires special timing or additional features proceed to Program Mode The system must be Tach Learned Tachless learned on Tachless models before the remote starter will make a start attempt If the remote starter does not make a start attempt check if the park lights are flashing a diagnostic code if so look the code up in the Diagnostic Chart to find the shutdown input that is preventing the system from starting If the vehicle does make a start attempt but fails to start Check all connections and insure that all wiring is connected correctly The vehicle may be equipped with a factory anti theft system Vehicles equipped with factory anti theft systems will usually have some sort of Security or Anti Theft light located in the instrument cluster OWAY REMOTE STARTER ALARM INSTALLATION MANUAL Page 5 Wiring Diagram 11 pin 4 pin Connectors i 30amp Output Starter Output YELLOW 30amp Output Heater Acc Output GREEN 30amp Input Power Input RED 30amp Input Power Input RED 30amp Output Selectable Output WHITE 30amp Output Ignition Output BLUE Negative Outp
31. ut BLUE SPINK These connections are for manual transmission vehicles only j M models must always be installed into manual transmission vehicles Manual transmission M modules are cased in Yellow plastics Note 250ma outputs are low current and may require the installation of a relay for the activation of optional features INSTALLATION MANUAL 2WAY REMOTE STARTER ALARM Page 6 Wiring Diagram 14 pin connector 30amp Output Starter Output YELLOW 30amp Output Heater Acc Output GREEN 30amp Input Power Input RED 30amp Input Power Input RED 30amp Output Selectable Output WHITE 30amp Output Ignition Output BLUE sina Ouput Starter kill amp Ant Grind Output ORANGE enpa Brake Switch Input PINK _ _ _ AIC Input Tach Detection Input BLUE WHITE or Input Diesel Glow Plug Input BLUE These connections are for manual transmission vehicles only M models must always be installed into manual transmission vehicles Manual transmission M modules are cased in Yellow plastics i Note 250ma outputs are low current and may require the installation of a relay for the activation of optional features OWAY REMOTE STARTER ALARM INSTALLATION MANUAL Page Wiring Diagram auxiliary connectors The centre pin of the keyless entry harness is not to be used for anything besides plug in devices such as the VP 1 DL 3 DL 7 and Data Bus Modules Overloading this output will damage
32. volts in the accessory and run positions and 0 volts during start 3 Red 30amp Power Input 12volts at ignition harness or from battery Supplies power for the ignition selectable output and park light relays 4 Red 30amp Power Input 12volt power at ignition harness or from battery Supplies power for accessory and start relays 5 Blue 30amp Ignition Output This wire will test Ovolts in the off and accessory position 12volts in the ignition start and run 6 White 30amp Select Output Selectable output for 2nd Ign acc or starter Auxiliary Connectors 4 11 and 14 pin Connectors Pin Number Function Description 1 Yellow Re Arm Output 0 75 second pulsed output when locked and on remote start shutdown Used for factory alarm re arm Programmable output See Menu 3 2 Red Wht Trunk Release Output Hold the unlock button for 3 seconds Output will stay on until the unlock button is released Max 5 seconds Programmable to Park lights See Menu 2 3 Brown Disarm Output 0 75sec pulsed output when unlocked and pulse before remote start activation Used for Factory Alarm Disarm 4 Orange Starter Kill and Negative While Running Output Active when armed and or during remote start Anti Grind Used for optional starter disable and anti grind relay Programmable output See Menu 3 5 White Blue Siren Output Output to activate siren Programmable output See Menu 1 amp 2 6 Black White Park Brake Input Input to detect Pa
Download Pdf Manuals
Related Search