U-Line 1175BEV Refrigerator User Manual
Contents
1. ULIN 0074 A Figure 4 The LIGHT button Figure 4 1 on the control panel is used to change the lighting fundions To turn the lights and display OFF for a preset 36 hour interval blackout Sabbath mode not Star K certified 1 Press and hold the LIGHT button Figure 4 1 for ten seconds and release the F symbol will flash briefly at the end of the ten second period 2 The interior light and control display Figure 4 3 will go dark for the next 36 hours NOTE Although the display will not be visible the temperature controls in the unit remain active and the interior temperature will be maintained 3 To exit the blackout Sabbath mode not Star K certified before the 36 hour period repeat Step 1 Model 1175BEV has another mode of lighting available To illuminate the interior of the cabinet for a timed four hour period 1 Pressand release the LIGHT button Figure 4 1 to switch from door operated lighting control to the timed four hour lighting period the F symbol will flash briefly after the LIGHT button is pressed 2 At the end of the four hour period the light will turn OFF and door operated lighting control will resume 3 To exit the timed lighting control before the end of the four hour period repeat Step 1 1115R 1175R 29R 1175BEV 7 y U LINE cCORPORATION Electronic Control Panel 5 VA COOLER2. ULIN_0074_A Figure 7 To adjust the set point temperature 1 Press and release either the WARMER Figure 7 4 or COOLER Figure 7 5 button to put the controller in the SET TEMPERATURE mode The F or C symbol will begin to flash NOTE If no further action is taken this mode will self cancel in five seconds and the original set point temperature will be displayed 2 Within five seconds while the F or C symbol is flashing press the WARMER or COOLER button as required to adjust the set point temperature 3 The change will be set five seconds after adjusting the temperature and the new set point will be displayed Figure 7 3 Many factors can affect the internal temperatures of the cabinet They include e Temperature setting e Ambient temperature where installed e The number of times and length of time the door is opened and dosed s The amount of time the internal light is illuminated This affects primarily product on top rack or shelf e Installation in direct sunlight or near a heat source UFLINE CORPORATION Manual Temperature Control Model 29R ULIN 0014 A Figure 8 Adjust the temperature by turning the numbered dial Figure 8 1 in small increments Turn knob clockwise to make unit colder and counterdockwise to make unit warmer After adjusting temperature allow 24 hours for unit to stabilize Many factors can affed the internal temperature
3. F flashes after first touch set point saved ieee after 5 seconds of Touch and release Touch to change temperature SE and F stops flashing View Actual B 70 WC models will scroll Temp Hold 5 seconds Release when F flashes J O EG top mid bottom temps Change F C T Hold COOLER COOLER COOLER or l DE AE Se 8 F Blackout will end in 36 Blackout WW Display and cabinet light will not Mode Hold 10 seconds operate in Blackout Mode hours or hold again to terminate early Cabinet Light Gm LI Li Ve LI o x Light normally goes on off with door opening Pressing light button will turn interior light on for 4 hours then it will turn off Display Off Mode WARMER ON ON ON OFF OFF OFF Display off when door is closed unless cabinet light isturned on Repeat to switch back NOTE 38 F is an example the display will vary with actual set point IMPORTANT Factory recommended set point is 38 F for refrigerators and beverage centers and 50 F for wine coolers 1115R 1175R 29R 1175BEV 27 ID U LINE Origins Series CORPORATION This page intentionally left blank 28 1115R 1175R 29R 1175BEV Origins Series m U LINE CORPORATION This page intentionally left blank 1115R 1175R 29R 1175BEV 29 ID U LINE Origins Series CORPORATION This page intentionally left blank 30 1115R 1175R 29R 1175BEV CORPORATION
4. ULIN 0074 A Figure 5 Models 1115R 1175R and 1175BEV The electronic control with digital display Figure 5 is configured to show a single temperature continuously This set point temperature is a base number used by the controller to maintain the temperature zone in your unit The factory default set point is 38 F This set point temperature is used as a gauge if further temperature adjustments are required Model 1175BEV has a DISPLAY OFF mode available through the control panel This mode allows you to control whether the display Figure 5 3 will be ON or OFF whenever the door is dosed The button sequence that follows will switch between both modes 1 Pressand hold the WARMER button Figure 5 4 and simultaneously within five seconds press the ON OFF button Figure 5 2 three times 2 The display will be either visible or dark when the door is closed 3 To return to the previous mode repeat Step 1 Temperature Display Selection U Line products supplied for 110 VAC operation have temperatures displayed in a default Fahrenheit F configuration Figure 5 3 Models supplied for 220 VAC operation have temperatures displayed in a default Celsius C configuration The display can easily be adjusted for either type of temperature display Press and hold the LIGHT button Figure 5 1 and smultaneously within five seconds press the COOLER button Figure 5 5 three times to change the display as desired
5. Temperature Display To display actual temperature 1 Pressthe WARMER button Figure 5 4 for five seconds The display Figure 5 3 will indicate the actual temperature 2 After approximately 10 seconds the set point temperature will return to the display ULIN_0093_A Figure 6 IMPORTANT U Line recommends a set temperature of 38 F on all refrigerators To check the actual product temperature in your unit insert an accurate thermometer into a plastic non breakable bottle that is partially filled with water Tighten the bottle cap securely Figure 6 Place the bottle in the desired area for 24 hours Refrain from opening the unit during the testing period After 24 hours check the temperature of the water If required adjust the temperature control in a small increment See ADJUSTING TEM PERATURE Factors which affect the internal temperatures of the cabinet include e Temperature setting e Ambient temperature where installed e The number of times and length of time a door is opened and closed e The amount of time the internal light is illuminated This affects primarily product on top rack or shelf e Installation in direct sunlight or near a heat source 8 1115R 1175R 29R 1175BEV Origins Series Adjusting Temperature IMPORTANT Adjust the set point temperature in single increments and wait 24 hours for the temperature to stabilize before rechecking
6. Origins Series m U LINE U Line Corporation Limited Warranty U Line Corporation warrants each U Line produd to be free from defectsin materials and workmanship for a period of one year from the date of purchase and warrants the sealed system consisting of the compressor the condenser the evaporator the hot gas bypass valve the dryer and the connecting tubing in each U Line product to be free from defects in materials and workmanship for a period of five years from the date of purchase During the initial one year warranty period for all U Line products U Line shall 1 at U Lines option repair any product or replace any part of a product that breaches this warranty and 2 for all Marine RV and Domestic U Line products sold and serviced in the United States including Alaska and Hawaii and Canada U Line shall cover the labor costs incurred in connection with the replacement of any defective part During years two through five of the warranty period for the sealed system U Line shall 1 repair or replace any part of the sealed system that breaches this warranty and 2 for all Marine RV and Domestic U Line products sold and serviced in the United States including Alaska and Hawaii and Canada U Line shall cover the labor costs incurred in connection with the replacement of any defective part of the sealed system All other charges including transportation charges for replacements under this warranty and labor costs not specifically cove
7. Dealer Name Serial Number Dealer Address Purchase Date Dealer Telephone 2 1115R 1175R 29R 1175BEV Origins Series y U LINE CORPORATION 2 Table of Contents Jetggetel to del EE EE 2 Warranty Registration ANNER 2 Please Record Your Model Information u ummumaanna nanana ana a na aaaawnawanawaanasananawaanwaanaasananananann 2 Table of Contents NAA a ANAN NAAN 3 Safety PreCautl ONS mma ee T BIBIG ANNA NENA NAN 5 Safety Alert Definitions kA EEN 5 General Pre GULONG ANA NINI BANI NAAN 5 Neel te de TEE 6 Origins Refrigerator Models 1115R 1175R 29R E 6 Origins Beverage Center Model 1175BEV AAA 6 Operation mamuaaasamanlaasala anaE ESA INAANAK IN DAMBANA ANA BANAAG naa 7 Wr ANCA SEA CU PD xe sexed ea ds ATA ADA NYA PAN Da DOG 7 Interior Lighting EEN 7 Electronic Control Panel 071111 amba RURIA NAGANA AGARAN ARENA nInb again 8 Manual Temperature Control u mmaaaaaaaawawaaanawaa aa nawasaNaSKNGNN AN GN AE NAG NNKANAN KNANG ANG eae seeiaeeaeeeseeee 9 Veto e eg nl WEE 9 Wine Stocking Recommendations EE 10 Outdoor Marine and RV Usage EEN 10 Storage Vacation MOVING aaa NN DINAANAN arnt 10 Product Disposal Wine Guide naaa aa hm AA aie ANG DAA Wine RECOMMENCATIONS EE 11 Cleaning and Maintenance EE 13 General CANIN 11am NA INA HANGAAN NABURA DUA GANA LARAGA 13 Maintehange breede ege Eed deeg ee 13 a ain cite ahi enim ui acne 24 Before Calling for Service E 24 If Service e UE 24 Replacement Paksa AABANG E ANAN
8. by first inserting the tab side back into the housing at a slight angle While gently pushing the lens towards the tab end push the free end up into the housing and release when you will hear a snap click 22 1115R 1175R 29R 1175BEV Origins Series UFLINE CORPORATION Wine Rack Removal Installation 1175BEV To remove a rack from the cabinet 1 Grasp the end of the rack and gently slide it out until it stops 2 Remove any bottles stored on the rack ULIN_0162_A Figure 51 3 Press the left rack release lever Figure 51 down and at the same time lift the corresponding right rack release lever up and pull the rack out until it is free of the tracks and the cabinet IMPORTANT Do not remove the track side rails from the cabinet To insert a rack in the cabinet 1 Align the left and right rack channels with the tracks in the cabinet and ensuring an even track engagement on both sides gently push the rack into the cabinet until it stops 2 Before reloading the rack ensure proper operation of the travel stopsin the left and right track rails by pulling the rack out gently until it completely stops Wood Trim Finishing Interior components of your U Line unit are equipped with a natural wood trim for appearance and durability Although this wood trim has been coated with a clear sealer at the factory it is recommended that the trim be stained if desired and receive a final fi
9. gasket should be firmly in contact with the cabinet all the way around the door no gaps Carefully examine the door s gasket to assure that it is firmly in contact with the cabinet Also make sure the door gasket is not pinched on the hinge side of the door ULIN 0143 A Figure 21 NOTE M odel 29R shown Figure 21 1 Loosen do not remove top Figure 21 and bottom hinge screws 2 Align door squarely with cabinet 3 Make sure gasket is firmly in contact with cabinet all the way around the door no gaps 4 Tighten bottom hinge screws 5 Tighten top hinge screws Origins Series Door Reversal Black or white unit doors may be left or right hand opening Depending upon the location of the unit it may be desirable to change the side on which the door is mounted Black Model 1115R To reverse the door perform the following 1 Remove the grille and grille cap two screws ULIN_0143_A Figure 22 2 Remove top hinge from cabinet three screws Figure 22 Hold door to keep it from falling 3 Lift the door off the bottom hinge ULIN_0121_A Figure 23 4 Remove bottom hinge from cabinet two screws Figure 23 16 1115R 1175R 29R 1175BEV UFLINE CORPORATION 7 Relocate plastic spacer bushing Figure 26 on bottom of door to opposite side and place door on bottom hinge pin Clean out bushing hole in door bottom with a screwdriver if necessary Hinge 0 os Plastic Plast
10. 36 10 Place door on lower hinge pin Align flat edge of top hinge with outer edge of unit and fasten upper hinge to unit four screws Figure 36 Partially tighten screws until door is aligned 11 Adjust door to assure proper seal Tighten upper and lower hinge screws securely 12 Replace four plastic plugs removed in Step 4 into holes on top of unit Replace screwsin holesin bottom of unit on opposite side 13 Replace the grille Model 29R To reverse the door perform the following ULIN_0197_A Figure 37 1 Remove the control knob Figure 37 1 by pulling it straight out away from grille U U LINE CORPORATION 2 Remove two screws from grille Figure 37 2 and save 3 Remove the grille and grille cap from unit ULIN 0143 A Figure 38 4 Remove top hinge from cabinet three screws Figure 38 Hold door to keep it from falling 5 Lift the door off the bottom hinge ULIN 0121 A Figure 39 6 Remove bottom hinge from cabinet two screws Figure 39 1115R 1175R 29R 1175BEV 19 CORPORATION LIRE Origins Series 9 Relocate plastic spacer bushing Figure 42 1 on bottom of door to opposite side and place door on bottom hinge pin Clean out bushing hole in door bottom with a screwdriver if needed Hinge O aos Plastic Plastic Plug Hole dy dy dy Plug Hole o o o Right Side Pa Jet Side Door Swing oo
11. GANAN BR AN haa 24 Troubleshooting BE Le ana NE amahan Nman 25 Electronic Control QUICK Guide 0m AA AA KGG 27 U Line Corporation Limited Warranty umuulan na wwan unawa na anna nakaw aa nas ENKKNNKE NAK NNKAAKKnnKnananananannsanns 31 1115R 1175R 29R 1175BEV 3 ID U LINE Origins Series CORPORATION This page intentionally left blank 4 1115R 1175R 29R 1175BEV Origins Series 3 Safety Precautions IMPORTANT PLEASE READ all instructions completely before attempting to install operate or service your unit e Proper installation procedures must be followed if this unit is being initially installed or is moved to a new location after being in service An INSTALLATION GUIDE for your unit providing complete installation information is available from U Line Corporation directly and must be consulted before any installation is begun U Line contact information appears on the rear cover of this guide This unit requires connection to a grounded three prong polarized receptacle that has been placed by a qualified electrician in accordance with applicable electrical codes Safety Alert Definitions Safety items throughout this guide are labeled with a Danger Warning or Caution based on the risk type 44 DANGER Danger means that failure to follow this safety statement will result in severe personal injury or death A WARNING Warning means that failure to follow this safety statement could resul
12. NMENT CHECK AND ADJUSTMENT Item s interfering with door Reposition or remove item s Dirty condenser coils Clean condenser See MAINTENANCE CONDENSER CLEANING Airflow to front grille blocked Airflow must not be obstructed to front grille See OPERATION High ambient temperature or Reposition unit exposure to direct sunlight Temperature not set cold enough Set control to a cooler setting See OPERATION Allow 24 hours for temperature to stabilize The unit frosts up Door gasket not sealing properly Adjust door See MAINTENANCE DOOR ALIGNMENT Door left open CHECK AND ADJUSTMENT High ambient temperatures or Defrost unit manually See MAINTENANCE humidity DEFROSTING Noise during operation Certain soundsare normal Soft sounds from the fan and water dropping sounds from the ice maker will be heard Fan blade touching obstruction Remove obstruction wiring foam insulation etc Unit too cold Temperature control set too cold Set control to warmer setting See OPERATION Freezing product Product touching evaporator in back Move product away from evaporator making sure it is of unit not touching evaporator 1115R 1175R 29R 1175BEV 25 UFLINE CORPORATILION U Troubleshooting Models with an electronic display Origins Series PROBLEM POSSIBLE CAUSE REMEDY Electronic display is blank and interior light isoff with door open Unit isin blackout Sabbath mod
13. Origins Series Use and Care Guide Refrigerator Models 1115R 1175R 29R Beverage Center Model 1175BEV 1115R 1175R y U LINE Or CORPORATION S ins Series 1 Introduction Congratulations on your purchase of a U Line refrigeration produd A pioneer in the field for more than 40 years U Line Corporation is the world s number one manufadurer of built in under counter specialty refrigeration and ice making products U Line dedicates 100 of its research and development to these products The result U Line technology consistently leads the market with innovation design depth of product line and performance U Line products are making life more convenient in homes businesses and hotels around the world U Line supports its products with a strong dealer network and its commitment to quality even extends to environmentally safe packaging IMPORTANT READ all of the instructions in this guide completely before operating the unit for the first time For future reference keep this guide in a safe accessible location If you need additional information or assistance please contact U Line Corporation directly Contact information appears on the rear cover of this guide If you have a problem with the operation of this product the SERVICE section of this guide will assist you in quickly identifying common problems and provide information on possible causes and remedies If your product needs service contact U L
14. aminer Germany Liebfraumilch Light Bodied Off Dry Germany Rhine Mosel Riesling Common Tasting Terms Terminology Acidity Balance Body Bouquet Complex Flabby Full Bodied Lean Oaky Tannin 12 Description A critical element of wine that is responsible for preserving the wines freshness Excess acidity resultsin an overly tart and sour wine A desired trait where tannin fruit and acidity are in total harmony Wines with good balance tend to age gracefully The weight and presence of wine in the mouth provided by the alcohol and tannin level Full bodied wines tend to have this strong concentration The blending of a wine s aroma within the bottle over a period of time caused by volatile acidity A subjective term often used in tasting A wine is said to be complex if it offers a variety of flavors and scents that continue to evolve as it develops A wine that lacks structure or is heavy to the taste lacks acidity Wine high in alcohol and extract generally speaking fills the mouth powerful Generally describes winesthat are slim lacking of generosity or thin A desirable flavor imparted to wine if done in moderation Most wines are aged in oak barrels one to three years thereby receiving this toasty oak characteristic However if a weak wine is left in contact too long with an oak barrel it will tend to be overpowered with an oaky taste Tannins are extracted from the grape skins and
15. d wines Asa general rule one should aim to ascend in flavor and quality of wines served Table 1 Serve a Before a DRY wine SWEET wine WHITE wine RED wine YOUNG wine OLD wine LIGHT BODIED wine FULL BODIED wine Any step back in quality will be noticed If a fine wine is tasted prior to a lesser wine many of the fine wine s subtle qualities may be missed Common Food and Wine Matches Table 2 Foods Fish Shell Fish Crab Oysters Wines Dry White Wines Light Sparkling or Extra Dry Champagne Beef Venison Full Bodied Red Wines Pork Veal Lamb and Poultry Light Bodied Red Wines Fruit Sweet White and Sparkling Wines 1115R 1175R 29R 1175BEV 11 U U LINE CORPORATION Series Guide to Common Styles of Wine Red Wines Full Bodied Dry California Zinfandel Cabernet French Rhone Chateauneuf du Pape Italian Barbaresco Barolo Medium Bodied Dry California Pinot Noir French Bordeaux Burgundy Light Bodied Dry French Beaujolais Italian Chianti Bardolino White Wines Full Bodied Dry California Chardonnay French Montrachet M eursault Puligny M ontrachet Medium Bodied Dry California Sauvignon Blanc French Pouilly Fuisse Sancerre Vouvray Graves Light Bodied Dry French Chablis Muscadet Pouilly Fume Full Bodied Very Sweet Germany Beerenauslese Frency Sauternes Hungary Tokay Medium Bodied Semi Sweet California Gewurtztr
16. ded in grille Figure 46 1 before attaching grille to unit and secure but do not overtighten both grille screws Figure 46 2 y U LINE CORPORATION Door Shelf Removal Insertion ULIN 0040 A Figure 47 NOTE 1115R and 1175R models only To remove the door shelf 1 Grasp shelf in center and lift until the shelf notches Figure 47 1 dear the bosses Figure 47 2 2 Carefully pull the shelf away from the door To install the door shelf 1 Holding the shelf in the center center the shelf in the door at the desired location sightly above the bosses Figure 47 2 2 Lower the shelf onto the bosses Figure 47 2 1115R 1175R 29R 1175BEV 21 y U LINE CcCORPORATION Glass Shelf Removal Installation ULIN 0199 A Figure 48 For Models 29R and 1175BEV Model 29R illustrated above reposition the shelves as follows 1 Open door completely 2 Grasp the shelf edge in the center Figure 48 1 and side the shelf from the unit 3 Reposition the shelf as required ensuring the raised white edge strip is toward the rear of the unit and the decorative graphics if applied are on the underside of the shelves IMPORTANT e Make sure the shelves are inserted fully into the unit e The white edge strip toward the rear prevents cans and bottles from freezing against the cold evaporator For all other models reposition the shelves as f
17. e not Star K certified Exit blackout Sabbath mode not Star K certified See OPERATION Electronic display is blank and interior light ison with door open A display function has changed Touch and hold the WARMER button and touch and release the ON OFF button three times then release the temperature button The display should become visible Electronic display shows repeating randomly flashing symbols and partial characters A factory control mode has been inadvertently entered Touch and hold the warmer temperature button and touch and release the LIGHT button three times then release the temperature button to exit the factory control mode The set point temperature should now be displayed Electronic display shows 0 1 to 16 or 99 A factory control mode has been inadvertently entered Repeatedly touch the WARMER button to advance any number shown to 99 and touch and release the LIGHT button The set point temperature should now be displayed Electronic display shows one or more of the following E1 E2 E4 E5 E6 The unit is displaying an error code Record the error code s displayed and call for service 26 1115R 1175R 29R 1175BEV Origins Ser ies Electronic Control Quick Guide Task Touch Touch U Display UFLINE CORPORATION Comment Turn ON OFF oe Hold 10 seconds WARMER COOLER Release when F flashes r WARMER o COOLER
18. e LED display while maintaining complete temperature control in the unit s All three models qualify for the U S Government ENERGY STAR program e All models feature maintenance free automatic cycle defrost s A generous capacity one piece molded interior is very durable and easy to clean e Model 1115R provides 3 3 cu ft 93 L of refrigeration Model 29R provides 3 5 cu ft 99 L of refrigeration and Model 1175R provides 5 7 cu ft 161 L of refrigeration e Adjustable tempered glass shelves are used Model 29R has two full shelves and one half shelf Models 1115R and 1175R have three shelves These shelves are designed to be easily deaned contain spills and may be positioned evenly throughout the interior to use all space efficiently e Models 1115R and 1175R have two inner door pick off shelves Model 29R has fixed shelves e All black and white models accommodate custom flat or raised door panels and can achieve a custom built in look by matching surrounding cabinets Please visit www u line com for additional panel information e Doorson black and white models are field reversible Stainless steel doors are not field reversible e Door locks for black and white 1175R and 29R models are only available factory installed at time of original order e Vinyl dad steel cabinets provide a rich textured look and resist scratching peeling or flaking Models 29R and 1175R are available in either black or whi
19. eration ULIN_0126_A Figure 2 IMPORTANT Proper air flow Figure 2 is required for your unit to operate at its highest efficiently A grille located in the base of the unit must not be blocked at any time or your unit will not perform as expected Initial Startup All U Line units are shipped with controls that are preset No initial adjustments are required IMPORTANT U Line recommends the unit be allowed to run overnight prior to loading with product ULIN_0127_A Figure 3 Models 1115R 1175R and 1175BEV To turn the unit ON or OFF press and hold the ON OFF button Figure 3 1 for approximately ten seconds and release The display will show the unit set point temperature when turned ON and display OFF when the unit is OFF Model 29R To turn unit off Turn the controller knob located in the center of the grille counterclockwise until a click is heard It may take some force to get the control to click To turn unit on Turn the controller knob located in the center of the grille clockwise to a MID setting number 3 or 4on the controller knob y U LINE CORPORATION Interior Lighting Model 1115R 1175R and 1175BEV The interior of the cabinet can be illuminated whenever the door is opened or remained darkened for a 36 hour period blackout Sabbath mode not Star K certified
20. hase It also appears on the Model and Serial number plate located on the upper right or rear wall of the interior of your product Replacement Parts When you need replacement parts always request that genuine U Line replacements be used U Line products have been designed and engineered using components that work efficiently and provide superior service life and performance The use of aftermarket parts or components may affect the safety operation performance or durability of your product and may also void its warranty 24 1115R 1175R 29R 1175BEV Ori Series y U LINE CORPORATION Troubleshooting Guide A DANGER NOTE Recommended temperature setting is 38 ELECTROCUTION HAZARD Never attempt to repair or perform maintenance on the unit until the main electrical power has been disconnected Troubleshooting What to check when problems occur PROBLEM POSSIBLE CAUSE REMEDY Unit does not operate and No electrical supply Plug unit in or check circuit breaker electronic display is blank No interior light Loose or burned out bulb Tighten or replace bulb See M AINTENANCE LIGHT BULB REPLACEMENT Light won t go out when door is Light on off switch isturned to ON Turn switch to OFF See OPERATION closed Model 1175BEV Unit not cold enough Light staying on Adjust door See M AINTENANCE DOOR ALIGNMENT CHECK AND ADJUSTMENT Door gasket not sealing properly Adjust door See M AINTENANCE DOOR ALIG
21. ic Plug Hole dy dy dy Plug Hole o o o Right Side A Left Side Door Swing Door Swing Right Side Invert Invert Hinge Screw Hinge ULIN 0122 A ULIN 0142 A Figure 24 Figure 27 5 Remove screwson opposite side of cabinet Figure 24 Note that there may be a nut behind one or both screws on either side 8 Remove plastic hole plug Figure 27 from door handle and relocate on opposite side 9 Remove pivot screw from top hinge invert screw and reinstall pivot screw in top hinge See Figure 30 ULIN 0144 A ULIN 0123 A Figure 25 Ee ee 10 Remove three plastic screw plugs Figure 28 from 6 Install hinge on opposite side bottom of cabinet hinge holes top of cabinet opposite side Be careful Figure 25 Replace nut on back side where installed EE cabinet Align hinge outer edge with cabinet before tightening 11 Place door on lower hinge pin Invert and install upper hinge on door screws ULIN_0109_A ULIN_0145_A Figure 26 Figure 29 1115R 1175R 29R 1175BEV 17 UFLINE CORPORATION 12 Fasten upper hinge to unit three saews Figure 29 Partially tighten screws 13 Adjust door to assure proper seal Tighten upper and lower hinge screws securely 14 Replace three plastic plugs removed in Step 10 into holes on top of unit Replace screws in holes in bottom of unit on opposite side 15 Replace the grille and grille cap Be sure to place grille cap on
22. ine directly Warranty Registration Your U Line Corporation Limited Warranty is located on the inside rear cover of this guide To validate your warranty the product and its original purchase date must be registered A Warranty Registration Card has been included for this purpose in the package containing this manual Complete and mail the Warranty Registration Card or register your product online at www U LineService com as soon as possible after purchase If your product registration is not on file and a request for warranty coverage is received the date of sale to the U Line Selling Dealer or Distributor will be established as the first date of warranty coverage for your product Please Record Your Model Information When you request additional information or service you will be asked for your products model and serial numbers You can find this information on the serial plate located on the upper right or rear wall in the interior of your unit This information also appears on the warranty registration card WEAD W U I ANE gen Up f RSR ER us USTED GR MILWAUKEE WISCONSIN USA HIGH SIDE DESIGN PRESSURE 300 PSI LOW SIDE DESIGN PRESSURE 140 PSI Model Serial No X XXXXXX XX 04 XXXX 05 XXXX X XHP 60 HZ 1 PHASE X XA R134A X XXOZ ULIN 0023 A Figure 1 Please record the model number Figure 1 1 serial number Figure 1 2 date of purchase and dealer contact information for your U Line product below Model Number
23. intended for stainless steel on stainless surfaces this includes glass tile and counter cleaners e If any surface discoloring or rusting appears clean it quickly with Bon Ami or Barkeepers Friend Cleanser and a non abrasive cloth Always clean in the direction of the grain Always finish this process with Claire Stainless Steel Polish and Cleaner or comparable product to prevent further problems e Using abrasive pads such as Scotchbrite will cause the graining in the stainless to become blurred e Rust that isnot deaned up promptly can penetrate into the surface of the stainless steel and complete removal of the rust may not be possible Interior Cleaning As Required e Disconnect power to the unit Clean the interior and all removed components using a mild non abrasive detergent and warm water solution applied with a soft sponge or non abrasive cloth Rinse the interior using a soft sponge and clean water y U LINE CORPORATION Do not use any solvent based or abrasive cleaners These types of cleaners may transmit taste to the interior products and damage or discolor the interior Maintenance Proper maintenance of your U Line product will ensure efficiency top performance and long life The maintenance intervals listed are based on normal conditions You may want to shorten the intervalsif you have pets or other special considerations Defrosting Automatic Cycle Defrost Models Automatic defrost mode
24. ls do not produce frost in normal operating conditions However a frost pattern may be noticed on the interior wallsif the unit is repeatedly opened in a high heat or high humidity location If this frost pattern does not dear within 24 hours your unit will require manual defrosting N WARNING DO NOT use any type of electrical heating device ice pick knife or other sharp instrument to defrost this could damage the inner lining or refrigeration system and void the warranty IMPORTANT The drain pan was not designed to capture the water created when manually defrosting To prevent water from overflowing the drain pan place towels or other absorbent materials over the interior drain trough under the evaporator Figure 10 1 before defrosting ULIN_0196_A Figure 10 1115R 1175R 29R 1175BEV 13 U U LINE cORPORATION To defrost 1 Turn unit off 2 Remove all products from the interior and prop the door in an open position 2 in 5 cm minimum w Allow the frost to completely melt naturally Clean the interior and all removed components using a mild non abrasive detergent and warm water solution applied with a soft sponge or non abrasive cloth NOTE DO NOT us any solvent based or abrasive deaners They will discolor or damage the interior A Dampen a soft sponge
25. m with 280 or finer grit sandpaper 3 Remove sanding dust with a dean dry cloth 4 The factory applied seal is compatible with virtually all finishes A low odor water clean up quick drying finish such as Minwax Polycrylic Protective Finish is recommended Minwax Polycrylic is an ultra fast drying water based finish Apply a thin coat of a clear protective finish following the container label directions 5 Lightly sand and reapply if desired 6 Allow the final coat to dry for 24 hours before reinstalling the trim to the cabinet interior components Origins Series 8 Service Before Calling for Service If your U Line product appears to be malfunctioning read through the OPERATION section of this guide to ensure that the function of all controls are clearly understood If the malfunction persists the TROUBLESHOOTING GUIDE in this guide will assist you in quickly identifying common problems and provide information on possible causes and remedies Most often this will resolve the problem without the need to call for service If Service is Required If you do not understand a troubleshooting remedy or your product needs service contact U Line Corporation directly Contact information appears on the rear cover of this guide You will be asked for your product Model and Serial Numbers This information should be recorded inside the front cover of this guide following the products original purc
26. ndations Model 1175BEV Specially designed wine racks allow for the proper horizontal storage of wine The bottles are properly positioned so the wine remainsin contact with the cork to assure that the cork does not become dry The wine racks should be stocked staggering the bottles as shown Figure 9 ULIN_0019_A Figure 9 Outdoor Marine and RV Usage Some U Line models are designed to operate in outdoor marine and RV environments For best performance keep the unit out of direct sunlight e If the unit will be shut off for five days or more prop door open to allow for air circulation and prevent mold and mildew IMPORTANT If the ambient temperature is expected to drop below 45 F turn off and unplug unit and drain all water from the unit to prevent freezing damage not covered by the warranty e High ambient temperatures 110 F or higher may reduce the unit s ability to reach low temperatures Origins Series Storage Vacation Moving If the unit will not be used for an extended period or otherwise stored follow these steps completely A WARNING Electrical Shock Hazard Disconnect power before servicing Before operating replace all panels Failure to do so may result in death or electrical shock 1 Remove all consumable contents from the unit 2 Disconnect the power cord from its outlet and leave it disconnected until the unit is returned to service 3 Clean and dry
27. ndle Never install or operate the unit behind closed doors Be sure front grille is free of obstruction Obstructing free air flow can cause the unit to malfunction and may void the warranty Failure to clean the condenser every three months can cause the unit to malfunction This could void the warranty Allow unit temperature to stabilize for 24 hours before use If your model requires defrosting never use an ice pick or other sharp instrument to help speed up defrosting These instruments can puncture the inner lining or damage the cooling unit Use only genuine U Line replacement parts Imitation parts can damage the unit affect its operation or performance and may void the warranty 1115R 1175R 29R 1175BEV 5 y U LINE eC ORPORATION 4 Product Features Origins Refrigerator Models 1115R 1175R 29R e Models 1115R and 1175R feature an electronic control panel with digital display that allows you to display the interior temperature and adjust the setting to your preference The electronic control and digital display provide an attractive appearance and its method of control permits precise temperature settings Model 29R is equipped with a manual temperature control e In Models 1115R and 1175R an interior light illuminates automatically as the cabinet door is opened Another mode of operation is available A blackout Sabbath mode not Star K certified allows you to darken both interior light and th
28. nguished itself asthe leader in built in under counter ice making refrigeration and wine storage appliances An INSTALLATION MANUAL for your unit providing complete installation information is available for download at www U Line com Information for custom panel inserts per model including panel size and instructions are available by visiting www U Line com When you need replacement parts always request genuine U Line replacements be used Visit www U Line com to locate a parts distributor in your area Echalon sents Origin e SERIES U Line Corporation located in Milwaukee WI is a family operated manufacturer of built in undercounter ice makers Combo e ice maker refrigerators Wine Captain wine storage units refrigerators refrigerated drawers and refrigerator freezers 2006 U Line Corporation Publication No 30087 01 2006 Rev A
29. nish coating prior to the unit going into full time service A WARNING To prevent permanent damage to the inner liner of your unit the wood trim MUST be removed from the unit for staining and or finishing Allow stain finish to dry thoroughly at least 24 hours per coat in accordance with the product manufacturer s instructions prior to reinstallation Failure to do so may cause the inner liner of the unit to have a permanent odor which is not covered by the warranty If staining the trim is desired it must be done before the application of any type of final finish Review the following staining final finish and final finish only guidelines when staining and or sealing the wood to ensure proper adhesion and durability of the finish NOTE Glass in door is tinted Stain may look darker when door is closed Staining and final finish application 1 Remove all screws securing wood trim to interior components and remove the trim from the cabinet interior NOTE Your model may contain an electronic display panel in the lowest level trim piece After removing the trim screws and gently pulling the trim from its location a wiring harness connector will become visible Unplug the connector and remove the trim from the interior IMPORTANT DO NOT use oil based stains on wood trim Vapors from oil based stains will permanently penetrate the liner and will not dissipate over time 2 Apply Minwax Water Based Wood Stain
30. ollows ULIN 0066 A Figure 49 1 Pull shelf out about 6 Figure 49 1 until back of shelf clears the hump on the right hand side Origins Series 2 Tilt up right hand edge of shelf Figure 49 2 3 Remove shelf from unit by pulling out Figure 49 3 Insert the shelves as follows 1 To move to a different position in the unit insert shelf at an angle approximately 15 20 over the rib in the side of the unit where you want to place the shelf The shelf must be started into the unit at an angle to clear the door 2 Continue to slide the shelf into the unit at an angle until it clears the door 3 Lower the shelf and push it in completely Light Bulb Replacement 1115R 1175R and 1175BEV To replace the light bulb in your U Line unit ULIN 0001 A Figure 50 1 Grasp the edges of the light housing lens Figure 50 1 opposite the exposed tab and gently push the lenstowards the tab Figure 50 2 2 Pull the edge of the lens down Figure 50 1 and swing it out of the light housing IMPORTANT ALWAYS use a genuine U Line replacement bulb P N 31317 in the light housing Use of any other bulb within the housing will generate excessive heat causing damage to the light housing and cabinet interior and compromising the precise temperature control of your unit 3 Replace the bulb only with a genuine U Line P N 31317 replacement 4 Replace the lens
31. opposite side of unit from where it was originally Black or White Model 1175R To reverse the door perform the following 1 Remove the grille two screws ULIN 0104 A Figure 30 2 Remove top hinge from cabinet four screws Figure 30 Hold door to keep it from falling 3 Lift the door off the bottom hinge ULIN 0105 A Figure 31 4 Remove four plastic plugs Figure 31 in hinge holes top of cabinet opposite side Be careful not to scratch cabinet Plastic Plastic Plug Hole Plug Hole Right Side Left Side Door Swing Door Swing Right Side Invert Invert Hinge Screw Hinge ULIN_0106_A Figure 32 5 Remove pivot screw from top hinge invert screw and reinstall pivot screw in top hinge Figure 32 Do not install hinge on cabinet at this time ULIN_0107_A Figure 33 6 Remove bottom hinge from cabinet four screws and screws on opposite side of cabinet Figure 33 7 Remove pivot screw from bottom hinge invert screw and reinstall pivot screw in hinge Figure 32 ULIN_0160_A Figure 34 8 Install bottom hinge on cabinet opposite side aligning flat edge of hinge with outer edge of unit Figure 34 Partially tighten screws 18 1115R 1175R 29R 1175BEV ULIN_0109_A Figure 35 9 Relocate plastic spacer bushing Figure 35 on bottom of door to the opposite side Clean out bushing hole in door bottom if necessary ULIN_0110_A Figure
32. or non abrasive cloth in dean water and wipe down the cabinet interior and removed components to remove any detergent residue Rinse the sponge or cloth in clean water and repeat as necessary until the cabinet and components are clean 5 When the interior is dry turn unit on Condenser Cleaning Interval Every Three Months To maintain operational efficiency keep the front grille free of dust and lint and dean the condenser every three months Depending on environmental conditions more or less frequent cleaning may be necessary A WARNING Disconnect electric power to the unit before cleaning the condenser N WARNING DO NOT touch the condenser fins The condenser fins are SHARP and can be easily damaged IMPORTANT DO NOT use any type of cleaner on the condenser unit Model 29R 1 Disconnect power to the unit ULIN_0197_A Figure 11 2 Remove the control knob Figure 11 1 by pulling it straight out away from grille 3 Remove two screws from grille Figure 11 2 and save Origins Series 4 Remove grille and grille cap from unit ULIN_0153_A Figure 12 5 Clean the condenser coil Figure 12 1 using a using a soft brush with a combing action or vacuum cleaner Do not touch the condenser coil ULIN_0198_A Figure 13 6 Make sure grille cap is behind grille in slots provided in grille Figu
33. ouch the condenser coil U U LINE CORPORATION ULIN 0159 A Figure 18 5 Place the hook hinge Figure 18 1 located on the rear bottom side of the grille onto the front lip Figure 18 2 of the unit base Swing the grille up into position and align the screw holes on the grille to the grille screw hole on the cabinet 6 Secure but do not overtighten both grille screws Figure 18 3 7 Reconnect power to unit Leveling It isimportant that units equipped with adjustable feet are level for proper door and ice maker if equipped operation NOTE Models 29R DO NOT have leveling feet These models MUST be placed on a level surface to operate properly To level units with adjustable feet ULIN_0041_A Figure 19 1 Use a level to check the levelness of the unit from front to back and from side to side Level should be placed along top edge and side edge as shown Figure 19 1115R 1175R 29R 1175BEV 15 y U LINE CORPORATION D WO HW j f y SS Ss SS SS SSS S SSss M MJ M 2 f H f SSS tf Y f o ULIN 0042 A Figure 20 2 If the unit is not level adjust the feet on the corners of the unit as necessary Figure 20 3 Check the levelness after each adjustment and repeat the previous steps until the unit is level Door Alignment Check and Adjustment IMPORTANT Properly aligned the door s
34. pond to your inquiry and it may also be selected to appear on our Questions and Answers page Wine Selections Suggestions Selecting the right wine for the right occasion can sometimes be a seemingly awkward or difficult task for the beginning wine enthusiast We would therefore like to present you with a few suggestions which may provide a little more confidence and enjoyment when choosing and serving your wines When selecting wines keep an open mind and do not be afraid to be adventurous Do not view the subject of wine so seriously it discourages you from learning and discovering for fear of embarrassment if something is incorrect Wine is best viewed as a hobby and enjoyed When assembling your collection try not to become obsessed with Vintages Although a chart can bea useful tool generalizations about a specific year have led more than one collector to disappointment In many instances an Off Year will provide a better value and more drinking enjoyment The primary guideline to the subject of wine is your own palate Do not be afraid to make mistakes Experiment discover but most of all enjoy yourself and your new U Line product y U LINE CORPORATION Suggestions for Matching Food and Wine Although there are no hard fast rules for matching wine to food observe some guidelines Delicate dishes should be accompanied by lighter more delicate wines Full flavored foods should be matched with fuller bodie
35. r Swing Right Side Invert Invert Hinge Screw Hinge ULIN 0122 A ULIN 0142 A Figure 40 z Figure 43 7 Remove screwson opposite side of cabinet Figure 40 Note that there may be a nut behind one or both screws on either side 10 Remove plastic hole plug from door handle and relocate on opposte side Figure 43 11 Remove pivot screw from top hinge invert saew and reinstall pivot screw in top hinge Figure 43 ULIN_0144_A ULIN_0123_A Figure 44 Figure 41 g PORE i 12 Remove three plastic screw plugs Figure 44 in hinge 7 Install hinge on opposite side bottom of cabinet holes top of cabinet opposite side Be careful not to Figure 41 Replace nut on back side where installed p y e S h R scratch cabinet Align hinge outer edge with cabinet before tightening Screws 13 Place door on lower hinge pin Invert and install upper hinge on door ULIN_0109_A Figure 42 20 1115R 1175R 29R 1175BEV Origins Series ULIN_0143_A Figure 45 14 Fasten upper hinge to unit three saews Figure 45 Partially tighten screws until door is aligned 15 Adjust door to assure proper seal Tighten upper hinge screws securely 16 Replace three plastic plugs removed in Step 11 into holes on top of unit Replace screws in holes in bottom of unit opposite side 17 Re inspect door seal and alignment Adjust if needed ULIN 0198 A Figure 46 18 Make sure grille cap is behind grille in slots provi
36. re 13 1 before attaching grille to unit and secure but do not overtighten both grille screws Figure 13 2 7 Reinstall the control knob Figure 11 1 8 Reconnect power to the unit Model 1115R 1 Disconnect power to the unit sl com 1E J c os ULIN_0155_A Figure 14 2 Loosen the two screws Figure 14 1 completely NOTE Screws are held in the grille by o ring retainers and will not come free of the grille 3 Remove grille Figure 14 2 and grille cap Figure 14 3 from unit 14 1115R 1175R 29R 1175BEV ULIN_0156_A Figure 15 4 Clean the condenser coil Figure 15 1 using a using a soft brush with a combing action or vacuum cleaner Do not touch the condenser coil ULIN_0157_A Figure 16 5 Make sure grille cap Figure 16 1 is behind grille in slots Figure 16 2 provided in grille before attaching grille to unit and secure but do not overtighten both grille srews Figure 16 3 6 Reconnect power to the unit Models 1175R and 1175BEV 1 Disconnect power to unit ULIN_0158_A Figure 17 2 Loosen the two screws Figure 17 1 completely NOTE Screws are held in the grille by o ring retainers and will not come free of the grille 3 Remove grille from unit 4 Clean the condenser coil Figure 17 2 using a using a soft brush with a combing action or vacuum cleaner Do not t
37. red by this warranty shall be borne by you This warranty is extended only to the original purchaser of the U Line product The Registration Card included with the product should be promptly completed by you and mailed back to U Line or you can register on line at www U LineService com The following are excluded from this limited warranty installation charges damages caused by disasters or acts of God such as fire floods wind and lightening damages incurred or resulting from shipping improper installation unauthorized modification or misuse abuse of the product customer education calls food loss spoilage door and water level adjustments except during the first 90 days from the date of purchase defrosting the product adjusting the controls door reversal or deaning the condenser If a product defect is discovered during the applicable warranty period you must promptly notify either the dealer from whom you purchased the product or U Line at P O Box 245040 Milwaukee Wisconsin 53224 or at 414 354 0300 In no event shall such notification be received later than 30 days after the expiration of the applicable warranty period U Line may require that defective parts be returned at your expense to U Lines factory in Milwaukee Wisconsin for inspection Any action by you for breach of warranty must be commenced within one year after the expiration of the applicable warranty period This limited warranty is in lieu of any other warranty e
38. s of the cabinet They indude e Temperature setting e Ambient temperature where installed e The number of times and length of time the door is opened and closed e The amount of time the internal light is illuminated This affects primarily product on top rack or shelf e Installation in direct sunlight or near a heat source Normal Operating Sounds All models incorporate rigid foam insulated cabinets to provide high thermal efficiency and maximum sound reduction for its internal working components In spite of this technology your model may make sounds that are unfamiliar Normal operating sounds may be more noticeable because of the unit s environment Hard surfaces such as cabinets wood vinyl tiled floors and paneled walls have a tendency to reflect normal appliance operating noises Common refrigeration components and a brief description of the normal operating sounds they make are listed below NOTE Your product may not contain all of the components listed e Compressor The compressor makes a hum or pulsing sound that may be heard when it operates e Evaporator Refrigerant flowing through an evaporator may sound like boiling liquid e Condenser Fan Air moving through a condenser may be heard e Automatic Defrost Drain Pan Water may be heard dripping or running into the drain pan when the unit isin the defrost cycle 1115R 1175R 29R 1175BEV 9 y U LINE CcCORPORATION Wine Stocking Recomme
39. stems and are necessary for a well balanced red wine Tannins are easily identified in wine tasting as the drying sensation over the gums Tannins generally fade as a wine ages 1115R 1175R 29R 1175BEV Origins Series 7 Cleaning and Maintenance General Cleaning Exterior Cleaning As Required Vinyl Clad Black or White Models e Surfaces may be cleaned with a mild detergent and warm water solution Do not use solvent based or abrasive cleaners Use a soft sponge and rinse with clean water Wipe with a soft clean towel to prevent water spotting e Clean any glass surfaces with a non chlorine glass cleaner Stainless Models e Stainless door panels handles and frames can discolor when exposed to chlorine gas pool chemicals salt water or cleaners with bleach e Keep your stainless unit looking new by cleaning with a good quality all in one stainless steel deaner polish on a monthly basis For best results use Claire Stainless Steel Polish and Cleaner which can be purchased from U Line Corporation P N 173348 Comparable products are acceptable Frequent cleaning will remove surface contamination that could lead to rust Some installations may require cleaning on a weekly basis e Do not dean with steel wool pads Do not use stainless steel cleaners polishes on any glass surfaces e Clean any glass surfaces with a non chlorine glass cleaner e Do not use cleaners that are not specifically
40. t can be illuminated continuously while the door is closed for a four hour period without resetting the unit providing a visible display of the Beverage Center contents b A blackout Sabbath mode not Star K certified allows you to darken the interior lighting and the LED display for a predetermined 36 hour period while maintaining complete temperature control in the unit This mode will self cancel at the end of the time period with the lighting and LED display returning to normal operation automatically e The upper chrome wine racks have a maple front trim that adds an attractive appearance to this model The wood fadng may be stained or replaced in its entirety with other woods or manufactured products such as Corian or Sandstone e The wine racks slide out and are 3 4 extendable providing access to all wine bottles including those located on the rear portion of the rack e This model features maintenance free automatic cycle defrost e The Model 1175BEV is only available in stainless steel The Model 1175BEV features a stainless steel door frame and hinges with black cabinet and grille e The door featuresa full length handle and tinted thermal glass that protects your wines from potentially harmful light rays while providing a very stylish appearance e The door isnot field reversible Features and specifications are subject to change without notice 6 1115R 1175R 29R 1175BEV Origins Series 5 Op
41. t in serious personal injury or death CAUTION Caution means that failure to follow this safety statement may result in minor or moderate personal injury property or equipment damage General Precautions Use this appliance for its intended purpose only and follow these general precautions along with those listed throughout this guide 44 DANGER RISK OF CHILD ENTRAPMENT Before you throw away your old refrigerator or freezer take off the doors and leave shelves in place so that children may not easily climb inside y U LINE CORPORATION A WARNING SHOCK HAZARD Electrical Grounding Required es Never attempt to repair or perform maintenance on the unit until the electricity has been disconnected Never remove the round grounding prong from the plug and never use a two prong grounding adapter Altering cutting of power cord removal of power cord removal of power plug or direct wiring can cause serious injury fire and or loss of property and or life and will void the warranty Never use an extension cord to connect power to the unit e Always keep your working area dry CAUTION e Use care when moving and handling the unit Use gloves to prevent personal injury from sharp edges e If your model requires defrosting DO NOT use any type of heater to defrost Using a heater to speed up defrosting can cause personal injury and damage to the inner lining IMPORTANT Do not lift unit by door ha
42. te Models 1115R is available in black only e Models1115Rand 1175Rare available in stainless steel and feature a stainless steel door panel and hinges with black cabinet and grille Origins Series Origins Beverage Center Model 1175BEV The Model 1175BEV Beverage Center will accommodate up to 16 standard 750 mL bottles of your favorite wines on its two upper 3 4 extendable siding wine racks The Beverage Center also provides generous storage for non wine beverages on two lower tempered shelves The Right Temperature for Wine Your Beverage Center has been designed to provide two temperature zones within the cabinet so the specific storage requirements of your beverages can be satisfied The upper wine rack zone maintains an approximate temperature of 45 F and the lower shelf zone maintains an approximate temperature of 38 F NOTE Product temperatures not air temperatures are referenced above e An electronic control panel with digital display allows you to display the interior temperature in the lower shelf zone and adjust the temperature setting The electronic control and digital display provide an attractive appearance and its method of control provides temperatures settings for a variety of wine and non wine beverages e An interior light will illuminate automatically as the door is opened providing easy visual identification of the contents You can also select two other modes of operation a The interior ligh
43. the interior of the cabinet See CLEANING AND MAINTENANCE GENERAL CLEANING 4 During periods of non use the cabinet must remain open to prevent the formation of mold and mildew Open door a minimum of 2 in 5 cm to provide the necessary ventilation Product Disposal If the unit is being removed from service for disposal check and obey all Federal State and or Local regulations regarding the disposal and recycling of refrigeration appliances and follow these steps completely 1 Remove all consumable contents from the unit 2 Disconnect power to the unit and unplug the power cord from its outlet 44 DANGER RISK OF CHILD ENTRAPEMENT Before you throw away your old refrigerator or freezer take off the doors and leave shelves in place so that children may not easily climb inside 3 Remove the cabinet door 10 1115R 1175R 29R 1175BEV Origins Series 6 Wine Guide Wine Recommendations To most wine is a delicious mystery We purchase it uncork it and savor its taste and beauty But there is so much more to true wine appreciation Many secrets are simply too good to keep bottled up The U Line Corporation is proud to present Spilling Wine Secrets online at www U Line com resources wine_secrets Take a moment to explore this section of our website to uncover wine myths learn ideal storage conditions or ask our wine expert Mr Dave Barna a specific question relating to wine Mr Barna will res
44. to wood with a synthetic bristle brush or a foam applicator Allow stain to penetrate approximately three minutes Before the stain isdry take a stain dampened rag and remove any excess stain remaining Wipe in the direction of the grain with medium pressure to achieve the desired stain color 3 After two hours repeat step 2 This will even out the color of the wood 4 Allow stain to dry for a minimum of three hours before applying the final finish 5 If desired sand the wood with very fine sandpaper to smooth the surface after the staining process 1115R 1175R 29R 1175BEV 23 y U LINE CORPORATION 6 Remove all dust from the wood and apply one coat of Minwax Polycrylic Protective Finish using a synthetic bristle brush to the wood This finish should be applied in a thin coat following the direction of the grain Apply the finish to the back and sides of the wood first and allow it to dry for two hours Apply the finish to the front side of the wood next and allow it to dry for two hours Sand with very fine 220 grit sandpaper Apply two addition coats of the finish in the same manner but do not sand the trim after the final third coat is applied 7 Allow the final coat to dry for 24 hours before reinstalling the trim to the cabinet interior components Final finish only application 1 Remove all screws securing wood trim to interior components and remove the trim 2 Lightly scruff sand the wood tri
45. xpress or implied including but not limited to any implied warranty of merchantability or fitness for a particular purpose provided however that to the extent required by law implied warranties are included but do not extend beyond the duration of the express warranty first set forth above U Lines sole liability and your exclusive remedy under this warranty is set forth in the initial paragraph above U Line shall have no liability whatsoever for any incidental consequential or special damages arising from the sale use or installation of the product or from any other cause whatsoever whether based on warranty express or implied or otherwise based on contract tort or any other theory of liability Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages so the above limitations may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state 1115R 1175R 29R 1175BEV 31 UI U LINE CORPORATION For General Inquiries P O Box 245040 Ori g in s Series Milwaukee Wisconsin 53224 9540 U S A Phone 800 779 2547 FAX 414 354 5696 www U Line com For Service and Parts Assistance Phone 800 779 2547 414 354 0300 FAX 414 354 5696 Email OnLineService U Line com www U LineService com E mail OnlineParts u line com For more than four decades U Line has disti
Download Pdf Manuals
Related Search