Toshiba IK-WD14A Security Camera User Manual
Contents
1. you to dangerous electrical or other hazards Refer all servicing to qualified service personnel 17 Damage Requiring Service Disconnect this camera from the power supply and refer servicing to qualified service personnel under the following conditions a When the power supply cord or plug is damaged b If liquid has been spilled or objects have fallen into the camera c If the camera has been submerged in water d If the camera does not operate normally by following the operating instructions in the user s manual Adjust only those controls that are covered by the user s manual as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the camera to its normal operation e If the camera has been dropped or the cabinet has been damaged f When the camera exhibiting a distinct change in performance which indicates a need for service g Other trouble 18 Other trouble Replacement Parts When replacing parts be sure the service technician uses parts specified by the manufacturer or have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards 19 Safety Check Upon completion of any service or repairs to this camera ask the service technician to perform safety checks to determine that the camera is in proper operating condition Important Safeguards Cont CAUTION TO2. 1697 Phone Number 877 855 1349 625015900G
3. REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons the user to the presence of important operating and maintenance The exclamation point within an equilateral triangle is intended to alert A servicing instructions in the literature accompanying the appliance WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE FIELD INSTALLATION MARKING WORDED THIS INSTALLATION SHOULD BE MADE BY A QUALIFIED SERVICE PERSON AND SHOULD CONFORM TO ALL LOCAL CODES 0 j Notes on Use and Installation Do not aim the camera at the sun Never aim the camera at the sun even with the camera power off Do not shoot intense light Intense light such as a spotlight may cause a bloom or smear A vertical stripe may appear on the screen However this is not a malfunction Treat the camera with care Dropping or subjecting the camera to intense vibration may cause it to malfunction Never touch internal parts Do not touch the internal parts of the camera other than the parts specified Keep the camera installation away from
4. and a non PoE switch PoE power injector not supplied non PoE switch not supplied Client PC not supplied General Connection without PoE 1 Connect the camera to an Ethernet switch via LAN cable 2 Connect the power cable from a power unit not supplied to the appropriate port of the general I O terminal See page 12 3 Connect the PC to an Ethernet switch via Ethernet cable Ethernet switch not supplied Client PC not supplied mms D ST NS AC 120V AC24V or DC12V adapter UL Listed Class 2 power supply not supplied FNOTE _ Recommended power cord is twisted pair line with a minimum wire size of 18 AWG The recommended power supply for this camera is 12 watts minimum When PoE is connected don t supply AC24V or DC12V from the I O terminal Never input AC24V and DC12V at the same time Assigning IP Address 1 Install the Installation Wizard under the Software Utility directory from the CD ROM 2 The program will analyze your network environment After your network is analyzed please click on the Next button to continue the program ja Installation Wizard Network Type amp Installation Wizard Network Type ES Installation Wizard Installation Wizard Your network environment was analyzed as below No connection to Internet izard is analyzing your network environment aa e wait a moment Install
5. by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Shielded interface cables must be used in order to comply with emission limits USER INSTALLER CAUTION Your authority to operate this FCC verified equipment could be voided if you make changes or modifications not expressly approved by the party Thank you for purchasing the IK WD14A Network Camera Before using the camera read this quick start guide carefully to ensure correct usage After reading this quick start guide save it for future reference The design specifications software and quick start guide contents are subject to change without prior notice Terms and Trademarks The term OS is used in this manual to indicate operating systems compatible with this product Windows XP Microsoft Windows XP operating system Windows Vista Microsoft Windows Vista Business operating system Windows 7 Microsoft Windows 7 Professional operating system The formal name of Windows is Microsoft Windows Operating System Microsoft Windows and Windows Vista are trademarks or registered trademarks of Microsoft Corporation in the United States and other countries Intel and Intel Core are tradem
6. or greater Connection equipment such as LAN cables and switch or router The LAN cable type differs depending on the connection method Camera search application Installation Wizard Install this application from the CD ROM supplied as an accessory Double click Setup exe in the CD ROM and install the application by following the onscreen instructions This application is the tool to discover the IP address of a camera Using this application the IP address of a camera can be easily determined Contents IK WD14A AV Out cable CD ROM Alignment Sticker NETWORK CAMERA IK WD14A Drill hole i P TOSHIBA Alignment Sticker m D Se Drill hole Us n u tart PIN B2XXXXXXXG Warranty Card Quick Start Guide and Important Safeguards TOSHIBA Leading Innovation gt gt gt NETWORK CAMERA Model IK WD14A Quick Start Guide and Important Safeguards Ie pide oe1ertes pe Nwasare roman Torx driver Screws and Anchors Physical Description Dome Cover Internal microphone Cover screws Knock out Tilt adjustment screws Lens cover OL A je 3 Mounting holes CAMERA MAIN UNIT Front View IR LEDs SR LED Lens Light Sensor Focus Button Built in Microphone Status LED Rear View General IO Terminal Block Micro SD 1 GND SDHC Card 2 Power input DC 12V Slot 3 Power input AC 24V 4 Po
7. pointer to rapidly adjust the zoom ratio The Focus pointer moves with the Zoom pointer correspondingly 2 Select Full view from the bottom of the screen 3 Click to select the Fully open iris check boxes When selected Full range scan a full range scan through the camera s entire focal length can take about 80 seconds If not the focus scan will only go through the length where optimal focus may occur and that takes about 12 seconds 4 Click on the START button and wait for the scan to complete 5 After a short while the clearest image obtained should be displayed and the optimal focus range is indicated by the densest color area on the color bar Use the N or F button to fine tune the focus if you are not satisfied with the results TOSHIBA Home KLEL Audio and Video gt Image Zoom Focus N One Touch Focus Full range scan V Fully opened iris START Focus window Full view Custom PNOTE _ The focus may shift due to the refractive index of the dome cover To avoid this verify the zoom and focus from your personal computer after installation One Touch Focus Depending on an object s conditions focus may not move to the optimal position In this case adjust the focus manually via the browser For more information please refer to user s manual on the CD ROM TOSHIBA AMERICA INFORMATION SYSTEMS INC Surveillance amp IP Video Products 9740 Irvine Boulevard Irvine CA 92618
8. video noise If cables are wired near electric lighting wires or a TV set noise may appear in images In this event relocate cables or reinstall equipment Check the ambient temperature and humidity Avoid using the camera where the temperature is hotter or colder than the specified operating range Doing so could affect the internal parts or cause the image quality to deteriorate Special care is required to use the camera at high temperature and humidity Should you notice any trouble If any trouble occurs while you are using the camera turn off the power and contact your dealer If you continue to use the camera when there is something wrong with it the trouble may get worse and an unpredictable problem may occur Setting the Network Camera Environment Items needed for network camera monitoring Administrator s personal computer The personal computer that allows setting operating monitoring and other functions with the network camera is called the administrator s personal computer in this guide The personal computer for viewing monitored images is called the user s personal computer in this quick start guide The network camera can be viewed by more than one personal computer at the same time Recommended personal computer system requirements Windows XP Windows Vista Business or Windows 7 professional Internet Explorer Ver 8 0 CPU Intel Core2 Duo 2GHz or greater Memory 1GB RAM
9. TOSHIBA Leading Innovation gt gt gt NETWORK CAMERA Model IK WD14A Quick Start Guide and Important Safeguards This guide describes the hardware installation Refer to the user s manual PDF file contained in the CD ROM for settings operations and other information The application Adobe Reader is needed to view PDF files If you do not have this application download it from the Adobe Systems Incorporated website E http www adobe com For information on our latest products and peripheral devices refer to the following Website E http www toshibasecurity com If the URL changes refer to the Toshiba website http www toshiba com 0 j Introduction FCC USA INFORMATION NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference
10. ad all the safety and operating instructions before operating the product 2 Retain Instructions Retain the safety instructions and user s manual for future reference 3 Warnings Comply with all warnings on the product and in the user s manual 4 Follow Instructions Follow all operating and use instructions 5 Cleaning Disconnect this camera from the power supply before cleaning 6 Attachments Do not use attachments not recommended by the camera manufacturer as they may pose safety risks 7 Water and Moisture Do not use this camera near water Some examples are near a bath tub wash bowl kitchen sink or laundry tub in a wet basement or near a swimming pool 8 Accessories Do not place this camera on an unstable cart stand tripod bracket or table The camera may fall causing serious injury to a person or serious damage to the product Use only with stand tripod bracket or table recommended by the manufacturer or sold with the camera Any mounting of the product should follow the manufacturer s instructions and should use a mounting accessory recommended by the manufacturer 9 Ventilation This camera should never be placed near or over a radiator or heat register If this product is placed in a built in installation verify that there is proper ventilation so that the camera temperature operates within the recommended temperature range 10 Power Sources This camera should be operated only from the type of powe
11. arks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries Adobe is a registered trademark and Adobe Reader is a trademark of Adobe Systems Incorporated ONVIF and Onvir are trademarks of ONVIF Inc Other product names appearing in this quick start guide may be trademarks or registered trademarks of their respective holders PNOTE _ The performance of the network camera may vary depending on the network environment Table of Contents Introduction 2 FCC USAJ INFORMATION b tan aaa ea riai siaii 2 Tenang Tae asa Rens deu nes 3 Table OC na ds 4 important SANG QUAI CS aa bae EAE enno an RET EER 5 Important Safeguards Cont T Notes on Use and INSTAIATION 48e ibmtehnenn 8 Setting the Network Camera Environment 9 Items needed for network camera monitoring 9 COMON na Sa ct 10 Physical DES CMO NOUN ena aa Ia 11 Hardware Installation civscszectonecseescedeieunscasactsiuesvanctedessaudexasadvtecsauntseavexsetetacsmess 13 Network Deployment cccssitiusanicideinuwdsiarsbinciandalidvindndideedavielssuertaneimodaiaadbuiadinbedls 15 Assigning IP PACE CS San en ina aah rien he 17 ee ag D LES 10 2 ea aa ee A EnF Dana benua 18 Adjusting the LENSA Berak et ana 19 DOME COV GM el and ne D ci ia time 20 Adjusting the Zoom and FOCUS ra tun etesn sectes errant 21 Important Safeguards 1 Read Instructions Re
12. ation Wizard 3 era Cable DSL modem Pc 3 The program searches for other Network Cameras on the same network 4 After searching the main installer window will pop up Click on the MAC address of the appropriate device to connect to the Network Camera q Installation Wizard Device Selection Installation Wizard Select a device to setup or upgrade Model mac IP Address 00 02 D1 71 42 70 169 254 0 99 IK WR12A TOSHIBA si NETWORK CAMERA MODEL No IK WD14A potest DC12V 0 5A AC24V 60Hz 0 5A r is ith Part 15 of the FCC Rules Operation is a 0002 D 1 i 1 4270 two Poran 1 this devi a compl n de la classe B est conforme a la norme MADE IN TAIWAN FABRIQUE EN FORMOSE TOSHIBA CORPORATION S N __A1010XXXX MAC 0002D1XXXXXX IBA ME Ww WN Please check the MAC and model name in the product label of your device first Then you can start to link to your device and show the main screen by double clicking the item in the above selection list Lens If you are not able to find your device in the ve selection list please make sure all bs 7 erly connected to your device You can find the product label in the Refresh Devices the rear bottom part of your device cables are proper and then click on button f NOTE f Installation Wizard does not find the camera during the
13. dio Video Out jack Adjustment of Viewing angle is possible using a portable monitor without using a personal computer when installing Use the included AV Out cable for this purpose Focus button When adjusting the viewing angle the camera focus may shift In this case push the focus button on the camera body for 2 seconds or more The zoom lens will move to a wide position and the focus will move to the optimal position PNOTE _ Depending on an object s conditions the focus may not move to the optimal position In this case focus the lens manually from your personal computer IMPORTANT Zoom and Focus adjustment is made via the Remote Focus function on your web browser There is no mechanical zoom or focus adjustment for the camera Dome cover 1 Attach the dome cover to camera 2 Secure the two dome screws with a screwdriver Make sure all parts of the camera are securely installed The supplied screwdriver is exclusively designed to match the dome screws Do not discard the screwdriver Adjusting the Zoom and Focus Access to the Network Camera from the network and click the configuration button on the main page Then click the following Audio and Video gt Image gt Zoom and Focus To adjust the zoom factor and focus range 1 Use the Zoom slide bar to find an optimal view of the area of interest where you want to adjust its focus Click and drag the double triangle
14. lot holes 90 28inchx1 57inches D O7mmx40mm D through the three circles on the sticker 3 Hammer the supplied plastic anchors into the holes 4 Drill a hole O1 0inch 925mm behind the camera body on the sticker and lead the cables through this hole 5 Align the three mounting holes of the Camera with the three plastic anchors insert the included three screws to the corresponding holes and tighten them with a driver Cable installation If possible lead all cables behind the camera body through a wall or ceiling If this is not possible use the knock out on the camera cover to route the cables through the side F NOTE _ Installation should be done only by qualified personnel and conform to all local codes Install this camera on a firm and solid part of the ceiling or wall If installed improperly or on a weak surface the camera could fall causing injury and damage Use Category Cat 5 or higher cable Network Deployment Power over Ethernet PoE e When using a PoE enabled switch The camera is PoE compliant allowing transmission of power and data via single LAN cable See the following illustration to connect the camera to a PoE switch via LAN cable y a NN lt gt O lt P Client PC ee 5 AL ND not supplied A TN PoE switch not supplied e When using a non PoE switch Use a PoE power injector not supplied to connect between the camera
15. r source indicated on the information label If you are not sure of the type of power supply at your location consult your product dealer 11 Power Cord Protection Power cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them Pay particular attention to cords at plugs screws and the point where they exit the product 12 Installation Install this camera on a secure part of the ceiling or wall If installed on an unsecured location the camera could fall causing injury and damage 13 Lightning For additional protection on this camera during a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the power supply and cable system This will prevent damage to the camera due to lightning and power line surges If lightning occurs do not touch the unit or any connected cables in order to avoid electric shock 14 Overloading Do not overload the power supply or extension cords as this can result in a risk of fire or electric shock 15 Object and Liquid Entry Never push objects of any kind into this camera through openings as they may touch dangerous electrical points or short out parts that could result in a fire or electrical shock Never intentionally spill liquid of any kind on the camera 16 Servicing Do not attempt to service this camera yourself as opening or removing covers may expose
16. search try turning off the wireless LAN of a PC Installation Wizard can search the location of the Network Camera even though DHCP is not used on the network In this scenario assign the camera a static IP address because the IP address of the Network Camera has been assigned 169 254 by default ONE Retrieving Images 1 Access the Network Camera from the network 2 Retrieve live video through Internet Explorer eee Network Camera Video stream 1 Auto es 100 Es sos Ea 25 Manual trigger Us 2011 10 15 02 19 12 Digital output PTZ panel Digital LJ EE y wo Pan speed fo x Tilt speed fo x Zoom speed fo x Global View 3 Client settings 3 Configuration SALA core For more information on camera configuration please refer to user s manual on the CD ROM Adjusting the Lens Based on the live image retrieved from the camera adjust the camera lens by performing the following To adjust the viewing angle 1 Turn the lens module left and right 2 Loosen the tilt adjustment screws on both side of the camera and then turn the lens module up and down Upon completion tighten the screws 3 Turn the lens cover to adjust the image orientation Pan 350 DO NOT over rotate the lens Doing so will damage the camera lens module Monitoring on the television This camera is able to output an analog NTSC or PAL video signal and sound from the Au
17. wer input AC 24V 5 Signal GND 6 Digital Input 7 Digital output 8 12V DC Output RRR RRR Microphone Video Output 10 100BaseT NTSC Ethernet Socket internal 60Hz MIC In Printed Audio In external Audio Video Out Printed AV Out 000 z Hardware Installation First use the supplied driver to detach the dome cover from the camera base Then follow the steps below to install the camera either to a ceiling or to a wall Bottom of the Camera NETWORK CAMERA MODEL No IK WD14A DC12V 0 5A AC24V 60Hz 0 5A This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device not cause harmful interference and 2 this device must accept any interference received including interference that ma i ti col e Cet appareil num rique de la classe B est conforme la norme NMB 003 du Canada TOSHIBA CORPORATION 2 MADE IN TAIWAN FABRI QU EN FORMOSE S N __A1010XXXX MAC 0002D1XXXXXX UL The included screws and anchors are used to install the camera to a solid surface e g concrete If installing on loose or thin material surfaces use the appropriate anchors not included with the screws Generally the camera turns a built in microphone in the direction of object Install the camera securely Mounting the camera to a solid surface 1 Attach the Alignment Sticker to the surface 2 Drill three pi
Download Pdf Manuals
Related Search