Toshiba EO1-19036M Scanner User Manual
Contents
1. TEC Laser Scanner LS 780 SERIES Owner s Manual gt e TOSHIBA TEC CORPORATION CE Compliance for EU only This product complies with the requirements of EMC and Low Voltage Directives includ ing their amendments Caution For U S and Canada use a UL Listed or Recognized ITE or Class 2 power supply unit having a L shaped output connector For Europe use a CE marked ITE or Class 2 power supply unit having a L shaped output connector Rated output of the power supply unit shall be 12 Vdc 10 800 mA or more FCC Notice for USA only This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio fre quency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Changes or modifications not expressly approved by manufacturer for compliance could void the user s authority to operate the equipment WARNING This is a Clas2. 1 APPEARANCE AND NOMENCLATURE 2 OPERATING PROCEDURE 2 4 BARCODE READING 4 MAINTENANG oe ease tet ces Hana anne Een 6 2 TROUBLESHOOTING ne nee ee 7 SPEGIFICATIONS mr 8 EO1 19036 LS 780 SERIES 1 INTRODUCTION Thank you for purchasing the TEC LS 780 Series Laser Scanner This manual describes the functions and handling of this Scanner and should be read carefully to help gain maximum performance and life from your Scanner For most queries please refer to this manual and keep it safe for future reference 2 LASER SAFETY Maintenance and Safety 1 Caution use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure 2 The use of optical instruments including a magnifying glass with this product will increase eye hazard 3 Avoid viewing direct laser beam for a long time Radiant Energy This scanner is an IEC Class 1 and CDRH Class laser product The system uses an embedded Class Mb VLD Visible Laser Diode operating at 650 nm in an optomechanical scanner resulting in less than 4 7 microwatts radiated power observed through 100 seconds Maximum peak output power is 840 microwatts Label e The following labels are placed on the back
3. Single Tone three times EEPROM Error Single Tone four times Decoder IC Error Single Tone five times Motor Error Single Tone six times Laser Error e When an error is detected during the normal operation This scanner also detects an internal error during the normal operation If an error is found during the normal operation the scanner informs you of error occurrence by the LED and the buzzer Number of the LED flickering and the buzzer beep is predetermined according to the error contents as shown below The error indication is repeated at the one second interval until the power of the scanner is turned OFF In case of the error occurrence inform your TOSHIBA TEC representative of the error status Error Indication Error Contents Single Tone three times EEPROM Error Single Tone five times Motor Error Single Tone six times Laser Error e When the power of the scanner is not turned ON e The power plug of the AC adapter is Insert the power plug into the power outlet securely inserted or is not securely inserted e The power is not supplied to the power outlet e Check the power supply using another electrical appliance e The connector of the interface cable has been de Attach the connector securely detached in case of the scanner of which power is controlled from the host terminal e The power of the host terminal is OFF in case of Turn the power of the host terminal the scanner of which
4. YA 3 4 Optional Parts Interface Cable OCIA Interface Cable RS 232C Interface Cable USB Model Name 750 Model Name Model Name IFC 780 USB IFC 750 RS 09F 26P 9P lt Female gt IFC 750 RS 25F 26P 25P lt Female gt IFC 750 RS 25M 26P 25P lt Male gt EO1 19036 LS 780 SERIES 4 OPERATING PROCEDURE Power Supply 1 When the AC Adapter on the market is used When the AC adapter is equipped with the power switch the scanner is turned on and off by turning on and off the power switch When the AC Adapter is not equipped with the power switch the power is supplied by plugging in the power cord no RPC function can be used 2 When the power is supplied from the host ECR POS The power can be supplied via the interface cable Ifthe host can control power supply to the scanner the host turns the scanner on and off Auto Power Off Function To save electricity this scanner has a function that laser and the motor are automatically turned off when the scanner does not read barcodes for a prescribed time At auto power off time the scanner enters reading standby state by pressing the Push Switch Since the laser and motor are turned on when the merchandise detect sensor detects something the scanner also enters reading standby state when anything like a hand is put above the Scanner Window 5 BARCODE READING This scanner reads barcode in the following range 5 1 Scanning Direction
5. There are two types of the scanner depends on setting position They are the vertical type and the horizontal type Each type can read barcodes in the following range The scanning pattern generated by an optical head unit is designed to achieve the best reading performance when an article is scanned as illustrated below Top Window 152 4 mm Scan Direction Scan Direction lt Seen from the above gt Top Window 121 mm LS 780H A EO1 19036 LS 780 SERIES 52 Effective Scanning Zone 15 A DR 81 8 46 3 LS 780H 79 53 5 LS 780H 5 3 How to Read Target the center of the Scanner Window so that the scanner can read a barcode of an item in the range at 50 mm to 200 mm above from the Scanner Window surface Article lt Seen from the front gt CAUTION 1 Do not contact the item and the Scanner Window 2 Moving the item perpendicularly to the Scanner Window makes it difficult to read the barcode Readable Barcode EAN JAN 13 EAN JAN 8 and UPC E EAN128 13 8 and UPC A E with Supplemental 2 or 5 digits ITF Interleaved 2 of 5 NW7 CODABAR CODE39 CODE93 CODE128 oe EO1 19036 LS 780 SERIES 6 MAINTENANCE To maintain reading precision above the prescribed level keep the Scanner W
6. 5 Shared power socket 7 Direct sunlight e Do not subject the machine to sudden shocks e Clean the cover and Top Window etc by wiping with a dry cloth or a cloth soaked with detergent and wrung out thoroughly Never use thinner or other volatile solvent for cleaning e At the end of the day turn the power OFF then clean and inspect the exterior of the machine e Try to avoid using this equipment on the same power supply as high voltage equipment or equipment likely to cause mains interference Do not place heavy objects on top of the machines as these items may become unbalanced and fall causing injury e Do not lean against the machine It may fall on you and could cause injury Request Regarding Maintenance e Utilize our maintenance services After purchasing the machines contact your authorized TOSHIBA TEC representative for assistance once per year Excessive vibration e Our maintenance service performs the periodic checks and other work required to maintain the quality and performance of the machines preventing accidents beforehand For details please consult your authorized TOSHIBA TEC representative for assistance e Using insecticides and other chemicals Do not expose the machines to insecticides or other volatile solvents as this will deteriorate the cabinet or other parts or cause the paint to peel EO1 19036 LS 780 SERIES TABLE OF CONTENTS Page INTRODUCTION essen EEN 1 LASER SAFETY
7. side and inside of the scanner lt US Type gt Back side Inside TEC LASER SCANNER LS 780 CLASS lla LASER PRODUCT No HE AVOID LONG TERM VIEWING OF DIRECT LASER LIGHT 12V UL us 540 DANGER LASER RADIATION WHEN OPEN ACCESSORY MANUFACTURED TOSHIBA TEC CORPORATION Ohito Plant 570 Ohito Ohito Chou Tagata Gun Shizuoka Ken 410 2392 JAPAN THIS LASER PRODUCT COMPLIES WITH THE FDA RADIATION This device complies with Part 15 of the FCC Rules PERFORMANCE STANDARD 21 CFR SUBCHAPTER J AS APPLICABLE Operation is subject to the foliowing two conditions AS A CDRH CLASS fla LASER 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may Cause undesired operation This Class A digital apparatus meets all requirements of the Canadian interference Causing Equipment Regulations Cet appareil num rique de la classe A respecte toutes les exigences du R glement sur le mat riel brouilleur du Canada lt QM Type gt TEC LASER SCANNER LS 780 Nm lev 0 7A TOSHIBA TEC CORPORATION JAPAN MANUFACTURED TOSHIBA TEC CORPORATION Ohito Plant IEC CLASS 1 LASER PRODUCT 570 Ohito LASER KLASSE 1 Ohito Chou APPAREIL LASER DE CLASSE 1 Tagata Gun Shizuoka Ken 410 2392 JAPAN EO1 19036 LS 780 SERIES 3 APPEARANCE AND NOMENCLATURE 3 1 Appearance Volume Switch LED Gre
8. d UPC A E with Supplemental 2 or 5 digits ITF Interleaved 2 of 5 NW7 CODABAR CODE39 CODE93 CODE128 Interface OCIA RS 232C USB Reading Height Up to 200 mm above from the Scanner Window surface Input Power 12 VDC 10 8 2 Interface Cable Option Cable Length 5 0 m TOSHIBA TEC CORPORATION on
9. e machine then contact your authorized TOSHIBA TEC representative for assistance Meanings of Each Symbol This symbol indicates warning items including cautions Specific warning contents are drawn inside the AA symbol The symbol on the left indicates a general caution This symbol indicates prohibited actions prohibited items Specific prohibited contents are drawn inside or near the Q symbol The symbol on the left indicates no disassembling This symbol indicates actions which must be performed Specific instructions are drawn inside or near the symbol The symbol on the left indicates disconnect the power cord plug from the outlet This indicates that there is the risk of death or serious injury if the machines are improperly handled contrary to this indication WARNIN Any other than the m Do not plug in or unplug the power specified AC voltage m Do not use voltages other than the Disconnect the plug cord plug with wet hands as this may cause electric shock is prohibited If the machines share the same outlet with any other electrical appliances which consume large amounts of power the voltage will fluctuate widely each time these appliances operate Be sure to provide an exclusive outlet for the machine as this may cause fire or electric shock Do not insert or drop metal flammable or other foreign objects into the machines through the ventilation slits as t
10. en Red Connector for AC Adapter on the Market Push Switch Scanner Window Interface Cable Connector Scanner Window Read a barcode of an item For barcode readable range refer to 5 BARCODE READING Connector for AC Adapter Connects the AC Adapter on the market on the market Complying with ElAJ RC6705 Interface Cable Connector Connects the Interface Connector Cable 26 pin OCIA type RS 232C type or USB type can be selected according to the host ECR POS specification EO1 19036 LS 780 SERIES 3 2 Switch Panel Volume Switch LED Green Red Push Switch LED Green Red Indicates scanner status using two color LED green and red The red LED lights when the scanner is ready to read a barcode and the green LED lights when a barcode is read normally Push Switch Pressed to return the scanner to reading standby state in auto power off mode Volume Switch Adjusts the buzzer volume of the scanner Each time the volume switch is pressed the buzzer volume changes as follows i Max Volume fi Loud Volume fi Medium Volume fi Min Volume Default Loud Volume Each time the volume switch is pressed while pressing the push switch the buzzer tone changes as follows i Low Tone fi Medium Low tone fi Medium Tone fi Medium High Tone fi High Tone fi Highest Tone Default Low Tone Owner s Manual 1 pc Connector Cover 1 pc Double Sems Screw 1 pc 3 3 Accessory 0 2
11. his may cause fire or electric shock Disconnect the plug E f the machines are dropped or their cabinets damaged first turn off the power switches and disconnect the power cord plugs from the outlet and then contact your authorized TOSHIABA TEC representative for assistance Continued use of the machine in that condition may cause fire or electric shock voltage AC specified on the rating plate as this may cause fire or electric shock Do not place metal objects or water filled containers such as flower vases flower pots or mugs etc on top of the machines If metal objects or spilled liquid enter the machines this may cause fire or electric shock Do not scratch damage modify the power cords Also do not place heavy objects on pull on or exces sively bend the cords as this may cause fire or electric shock E Continued use of the machines abnormal condition such as when the machines are producing smoke or strange smells may cause fire or electric shock In these cases immediately turn off the power switches and disconnect the power cord plugs from the outlet Then contact your authorized TOSHIABA TEC representative for assistance Safety Summary Disconnect the plug Connect a grounding wire a a I 217 N CAUTIO Precaution gt Disconnect the plug E f foreign objects metal fragments water liquids enter the machines first turn off the power
12. indow clean To clean the Top Window use a soft cloth Remove the Top Window as shown in the figure below and wipe the Top Window softly using a dry soft cloth When the Top Window is badly soiled use a cloth after moistening it with water and wringing water from it Then wipe the Top Window again using a dry cloth Clean the Under Window in the same manner Be careful not to damage the Under Window since it is made of acrylic and easily damaged 1 2 Top Window Window Frame Under Window Coin etc lt Removing the Window Frame gt lt Removing the Top Window gt 3 lt Cleaning the Scanner Window gt e Reassemble the Top Window so that the window cut part will be placed on the convex part of the Top Window Holder EO1 19036 LS 780 SERIES 7 TROUBLESHOOTING e When an error is detected at the power ON This scanner has the self diagnosis function to detect an internal error when the power is turned ON If an error is found at this time the scanner informs you of error occurrence by the LED and the buzzer Number of the LED flickering and the buzzer beep is predetermined according to the error contents as shown below The error indication is repeated at the one second interval until the power of the scanner is turned OFF In case of the error occurrence inform your TOSHIBA TEC representative of the error status Error Contents Single Tone once ROM Error Single Tone twice RAM Error
13. power 15 controlled from the host terminal When a trouble still exists after taking the actions described above ask your TOSHIBA TEC representative EO1 19036 LS 780 SERIES e When the scanner cannot read a barcode specification system corresponding to the scanner specification e Barcode has a defect Print of a barcode is too e Reading a barcode is unavailable light dirty blurred or defaced Read a perfect barcode attached to the same article Enter the barcode of the article manually by the keyboard However depending on the function of the host terminal e Angle to read a barcode is not appropriate e Read the barcode at the appropriate angle Refer to page 5 in details e Barcode to be read is too near to the top window Read the barcode in the effective scanning zone or too far from the top window Refer to pages 4 and 5 When a trouble still exists after taking the actions described above ask your TOSHIBA TEC representative e When the scanned data is not transferred to the host terminal e The connector of the interface cable has been de Attach the connector securely tached When a trouble still exists after taking the action described above ask your TOSHIBA TEC representative 8 SPECIFICATIONS 8 1 Scanner Main Body Dimensions 200 W x 90 D x 220 H mm Vertical standing dimensions Weight 1 5 kg Readable code EAN JAN 13 EAN JAN 8 UPC A UPC E EAN128 EAN 13 8 an
14. s A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures ATTENTION Ce produit est de classe A Dans un environnement domestique il peut causer des interferences radio Auquel cas l utilisateur sera amen a prendre les mesures ad quates Warnung Dies ist ein Klasse A Produkt In einer rtlichen Umgebung kann dieses Ger t Funkst rungen verursachen Atencion Este es un producto de la clase A En ambientes dom sticos ste producto puede causar radio interferencias en cuyo caso el usuario deber tomar las medidas oportunas VERWITTIGING Dit is een klasse A produkt Het gebruik hiervan kan radio interferenties veroorzaken die de gebruiker ertoe kunnen dwingen sommige maatregelen te moeten treffen Copyright O 2001 by TOSHIBA TEC CORPORATION All Rights Reserved 570 Ohito Ohito cho Tagata gun Shizuoka ken JAPAN Safety Summary EO1 19036 Safety Summary Personal safety in handling or maintaining the equipment is extremely important Warnings and Cautions necessary for safe handling are included in this manual All warnings and cautions contained in this manual should be read and understood before handling or maintaining the equipment Do not attempt to effect repairs or modifications to this equipment If a fault occurs that cannot be rectified using the procedures described in this manual turn off the power unplug th
15. switches and disconnect the power cord plugs from the outlet and then contact your authorized TOSHIABA TEC repre sentative for assistance Continued use of the machine in that condition may cause fire or electric shock Ensure that the equipment 15 properly grounded Extension cables should also be grounded Fire or electric shock can occur on improp erly grounded equipment Do not remove the glass surface top window except for cleaning as using the machine in this condition may adversely affect people s eyes Prohibited nm Ed er EO1 19036 When unplugging the power cords be sure to hold and pull on the plug portion Pulling on the cord portion may cut or expose the inter nal wires and cause fire or electric shock Do not remove covers repair or modify the machine by yourself It may result in hazardous radiation expo sure Unauthorized modification is prohib ited E Using the laser beam with large mirrors or optical equipment will result in increased risk to people s eyes and avoid viewing direct laser beam for a long time This indicates that there is the risk of personal Injury or damage to objects if the machines are improperly handled contrary to this indication The following precautions will help to ensure that this machine will continue to function correctly e Try to avoid locations that have the following adverse conditions Temperatures below 0 C and above 40 C
Download Pdf Manuals
Related Search