Toshiba B-210 SERIES Printer User Manual
Contents
1. conforming to IrDA SIR V1 0 Transmission speed 19200 bps Communicable distance 0 3 m max Peak wavelength of the infrared ray 850 to 900 nm Communicable angle 15 degrees max Ambient light immunity 1 000 Ix max under a fluorescent lamp or incandescent lamp Intensity of emission Min 36mW SR 6h v lt 15 Receivable infrared ray Min 7uW cmf 6h gva 15 Protocol Start stop synchroniza tion Half duplex transmission Start bit 1 bit Stop bit 1 bit 8 bit data Non parity 2 3 2 SPECIFICATIONS EM1 33043D 2 5 MEDIA 2 5 MEDIA fi direction Black Mark Receipt ra on reverse side Receipt paper Fig 2 1 2 4 2 SPECIFICATIONS faa Issue mode Label Receipt Pitch EM1 33043D 2 5 MEDIA Unit mm Batch mode Strip mode 10 0 167 0 13 0 67 0 Label Receipt length 7 0 160 0 10 0 60 0 Width including backing paper 34 37 40 43 46 49 52 5540 5 Media width Label 31 0 52 0 Receipt 34 37 40 43 46 49 52 55 0 5 Gap length 3 0 7 0 Black mark length 3 0 7 0 Effective print width 48 0 Effective print length 7 0 160 0 OD Margin 1 0 gap 7 mm 5 0 gap 3 mm Outer roll diameter 34 Max Roll way The print side facing inside Thickness Label2. 114m Receipt 65um NOTE Do not use media other than the above to ensure print quality and print head life 2 5 3 APPEARANCE EM1 33043D 3 1 FRONT REAR VIEW 3 APPEARANCE 3 1 FRONT REAR VIEW Front View REPRINT Button atus Indicator Power Switch r Battery Cover IrDA Interface Window Release Catch GH24 model only Battery Cover Media Cover Media Cover Release Catch Media Outlet Backing Paper Outlet Rear View Belt Holder Serial Interface Connector Fig 3 1 3 APPEARANCE EM1 33043D 3 2 OPERATION PANEL 3 2 OPERATION PANEL REPRINT Button Each time this button is pressed the printer issues the same label as REPRINT the previous one When the button is held the printer issues labels continuously STATUSO Receipts are fed for 20 mm by KE r pressing this button once STATUS Indicator Red The status indicator lights and then goes off at power on The indicator which does not light or stays litindicates the loaded battery is uncharged Power Switch A slide power switch 3 2 4 INSTALLING THE PRINTER EM1 33043D 4 1 LOADING THE BATTERY 4 INSTALLING THE PRINTER 4 1 LOADING THE BATTERY CAUTION 1 Be sure to turn off the printer before loading the battery 2 Use the specified battery only Failure to do this may cause fire or electric shock 3 In the United States used lithium ion batteries should be returned to the store where you b
3. 60 centigrade such as inside a car or 1 6 1 INTRODUCTION EM1 33043D 1 INTRODUCTION This indicates that there is the risk of CAUTION personal injury or damage to objects if the machines are improperly _ handled contrary to this indication e Keep away from flame or other sources of heat Failure to do this may cause fire or machine failure e Do not drop or shock the machine as this may cause machine failure e During lightening turn off and keep away from the machine because of danger of electric shock and machine failure e Avoidlocations subject to rapid change in temperature as this causes condensation causing electric shock or machine failure e Do not damage the print head platen or strip roller with a sharp object Doing so may cause machine failure e Do not touch or contact the print head element with a metal object Doing so may cause machine failure e Use the specified media only Failure to do this may cause machine failure e Be sure to turn off the machine before replacing the battery or machine failure may occur e Do not charge the battery near flame or under direct sunlight High temperature may activate or damage the protection unit of the battery disabling the electric charge or causing it to overheat burst or burn 1 7 INTRODUCTION EM1 33043D 1 INTRODUCTION Unload the battery when the machine will not be used for along time Failure to do this may cause machine failu
4. may contain components which shorten the print head s product life Do not use labels pre printed with ink which contains hard substances such as carbonic calcium CaCO and kaolin AI O 2SiO 2H O For further information please contact your local distributor or your media manufacturer 8 2 9 GENERAL MAINTENANCE EM1 33043D 9 1 CLEANING 9 GENERAL MAINTENANCE 9 1 CLEANING Care should be taken not to injure your hand with the cutter when cleaning To help retain the high quality and performance of your printer it should be regularly cleaned The greater the usage of the printer the more frequent the cleaning i e low usage weekly high usage daily 1 Turn off the printer 2 Open the media cover 3 Remove the media roll from the printer 4 Clean the print head element with the print head cleaner 5 Wipe the cutter platen and strip roller with a soft cloth moistened with alcohol Remove dust or foreign substances from the internal parts of the printer if any 9 GENERAL MAINTENANCE EM1 33043D 9 1 CLEANING 6 Remove paper particles or stains from the feed gap sensor black mark sensor and the batch strip sensor with a soft cloth Strip Mode Sensor 9 2 9 GENERAL MAINTENANCE EM1 33043D 9 2 COVERS AND OPERATION 1 Be sure to turn off the printer prior to performing any maintenance 2 Do not use any tool that may damage the print head 3 DONOT POUR WATER directl
5. media roll with the proper one Are the media cover release catches locked completely 10 2 Close the media cover so that the media cover release catches snap back into position TEC TOSHIBA TEC CORPORATION PRINTED IN JAPAN EM1 33043D 99010500 GS
6. TEC TEC Portable Printer B 210 SERIES Owner s Manual Document No EM1 33043D TOSHIBA TEC CORPORATION DECLARATION OF CONFORMITY Manufacturer TEC Corporation Address 570 Ohi to Ohito Cho Tagata Gun Shizuoka Ken 41 D 23 Japan declares that following product Product Name Bar Code Printer model B 210 Series options All Conforms to the following Product Specifications Safety EN 60 950 EMC EN 56 022 IEC 801 2 IEC 801 3 Supplementary Information The product herewith complies with the requirements of the Low Voltage Directive 73 23 EEC and the EMC directive 89 336 EEC 1 The product was tested in a typical set up TEC personnel advocated 2 The following technical documentation has been filed for review e Factory Inspection Certificate by TUV Rheinland e Owner s Manual e Schematic e Certificates and Test Reports 1 EM1 33043A TABLE OF CONTENTS Page INTRODUCTION onaaiiannnnananaaaannne 1 1 1 1 APPLICABLE MODEL 1 10 1 2 ACCESSORIES 1 11 SPECIFICATIONS oonniiannnnaaaannnnne 2 1 2 1 PRINTER a ssicassestacscadetncncncses 2 1 2 2 SERIAL INTERFACE RS 2320 eeeeeeeeeeeeeeeeEEEEEEEEEEe 2 2 2 3 RADIO INTERFACE 2 2 2 4 IrDA INTERFACE 2 3 2 5 NIESEN egbgeeepeg 2 4 APPEARANCE onaiiiaaaananananeee000ne 3 1 3 1 FRONT REAR VIEW 3 1 3 2 OPERATION PANEL 3 2 INSTALLING
7. THE PRINTER 4 1 4 1 LOADING THE BATTERY 4 1 4 2 INSTALLING THE MEDIA GUIDE onnnnnnnnnnnnnnnnnnn 4 3 LOADING THE MEDIA 5 1 SECURING THE PRINTER TO YOUR WAIST ccccccccceees 6 1 ISSUING THE MEDIA 7 1 CARE HANDLING OF THE MEDIA eege 8 1 EM1 33043A Page 9 GENERAL MAINTENANCE 9 1 9 1 CLEANING eee 9 1 9 2 COVERS AND OPERATION PANEL 9 3 9 3 REMOVING JAMMED MEDIA sissiaesanisnatesanisnstesivacaducans 9 4 10 TROUBLESHOOTING 10 1 CAUTION 1 This manual may not be copied in whole or in part without the prior written permission of TEC The contents of this manual may be changed without notification Please refer to your local Authorized Service representative with regard to any queries you may have in this manual Copyright 1997 by TEC CORPORATION All Rights Reserved 570 Ohito Ohito cho Tagata gun Shizuoka ken JAPAN 1 INTRODUCTION EM1 33043D 1 INTRODUCTION 1 INTRODUCTION Thank you for purchasing the TEC B 210 series portable printer The B 210 printer displays its high performance with extraordinarily high speed printing up to 50 8 mm sec It has a considerably compact and light body of 88 mm in height 128 mm in width and 50 mm in depth weighing about 460 g As data communication method minute radio communication for GH11 and GH12 models or IrDA GH24 model which requir
8. ack into position 5 4 5 LOADING THE MEDIA EM1 33043D 5 LOADING THE MEDIA 3 Turn on the printer and press the REPRINT button The printer will align the print start position NOTES 1 Be sure to take up any slack in the media roll before closing the media cover An incompletely closed cover will cause a media skew print position misalignment poor print quality paper jam etc 2 If the media cover is closed while the printer is turned on the printer will automatically feed a label to align the print position 5 5 6 SECURING THE PRINTER TO EM1 33043D YOUR WAIST 6 SECURING THE PRINTER TO YOUR WAIST 6 SECURING THE PRINTER TO YOUR WAIST CAUTION Care should be taken not to drop the printer when securing it to your waist 1 Lift the belt holder Belt Holder 2 Insert the belt holder into your belt and lower the printer to secure it to your waist Belt Holder Belt 6 1 7 ISSUING THE MEDIA EM1 33043D 7 7 ISSUING THE MEDIA ISSUING THE MEDIA CAUTIONS 1 Radio communication between a handy terminal and the B 210 printer is guaranteed when the handy terminal is in the operator s hand and the printer is secured at the waist Proper radio communication may not be obtained when used in other conditions and in areas subject to noise and radio interference Be sure to disconnect the RS 232C interface cable from the printer before performing radio communication
9. acters under bar codes 12x24 dots Writable characters 24x24 dots Times Roman 21 point Helvetica 18 point Letter Gothic 14 3 point Courier 15 point Presentation 27 point NW7 EAN 8 EAN 13 CODE 339 Interleave 2 of 5 PDF417 EAN128 CODE128 e GH11 mode RS 232C or MHz GH12 mode RS 232C or MHz GH23 mode RS 232C GH24 mode RS 232C IrDA Lithium ion battery 7 2V 1350mA official radio 418 radio 433 Available only on the GH23 model 2 1 2 SPECIFICATIONS EM1 33043D 2 2 SERIAL INTERFACE RS 232C 2 2 SERIAL INTERFACE RS 232C Baud rate 9600 bps XON XOFF 8 bit data Even parity Stop bit 1 bit TXD RXD RTS CTS 2 3 RADIO INTERFACE The following specification is applicable only to the GH11 and GH12 models Item Description Receiving frequency Communication method Transmission speed Protocol Communicating distance zs GH11 model zs GH12 model FM superhet UHF radio telemetry receiver Complies with MPT1340 ETS300 220 418 MHz 433 92 MHz Unidirectional Receive only 4800 bps 8 bit data non parity stop bit 1 bit 3m NOTE The RS 232C interface cable mustbe disconnected when using the radio communication 2 2 2 SPECIFICATIONS EM1 33043D 2 4 IrDA INTERFACE 2 4 IrDA INTERFACE The following specification is applicable only to the GH24 model Item Description Type Physical layer
10. d TOSHIBA TEC representative for assistance 1 INTRODUCTION EM1 33043D 1 INTRODUCTION Safety Precautions This Owner s Manual and the products machines which you have purchased contain indications which should be observed in order to use the machines safely and prevent harm to yourself and others and damage to property The meanings of these indications and symbols are given below Read these indications and become familiar with their contents before reading this Owner s Manual This indicates that there is the nek Ah WARNING Z contrary to this indication e f water or any other liquid enters the machine turn off the power Continuous use of the machine under such conditions may cause fire or electric shock e H the enclosure is damaged when dropped or subject to shock turn off the power Continuous use of the machine under such conditions may cause fire or electric shock e Avoid continuous exposure to direct sunlight or high temperature as this may cause fire e Do not remove covers or modify the machine by yourself Doing so may cause fire or electric shock 1 4 1 INTRODUCTION EM1 33043D 1 INTRODUCTION e Avoid water operation with wet hands or cleaning with a moistened cloth Failure to do this may cause fire or electric shock e Do not wipe the machine with a cloth moistened with thinner or other volatile solventas this may cause fire or electric shock e Use the specified battery o
11. es no cable for data transmission between a handy terminal and the printer is adopted Owing to alow power consumption design and use of a chargeable lithium battery as a power source this printer can issue 300 pieces of 40 mm pitch labels with a fully charged battery Loading a label roll is very simple just put a label roll into the printer and close the media cover A belt holder provided on the rear of the printer enables the printer to be held hands free at your waist for improved productivity This manual contains general set up and maintenance information and should be read carefully to help gain maximum performance andlife from your printer For most queries please refer to this manual and keep it safe for future reference 1 1 1 INTRODUCTION EM1 33043D 1 INTRODUCTION FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation Ifthis equipment does cause harmful interference to radio or television reception which can be de
12. icator Blinks Media end Action Load a new media roll The media cover is open Close the media cover completely The printer is jammed with media Turn off the printer remove the jammed media and re load the media roll correctly The print head element is broken Contact a TOSHIBA TEC service representative for repair A communication error occurred Check that the interface cable is connected firmly Check the communication parameters The battery voltage is low 10 1 Turn off the printer and replace the battery with a fully 10 TROUBLESHOOTING Other problems issue media 10 Did the status indicator light and then go off at power on EM1 33043D TROUBLESHOOTING Corrective action Charge the battery fully Is the printer turned on Turn on the printer Is the media roll loaded correctly Re load the media roll correctly Is the status indicator blinking or lighting Check the handy terminal for an error status and take appropriate action described in the handy terminal s operating manual Is the media cover closed completely Close the media cover completely Print failure Is the print head dirty Clean the print head with the attached print head cleaner Is the media discolored Replace the media roll with a new one Is the specified media used Replace the
13. mory of the printer could be lost during a printer fault DO NOT open the media cover and battery cover during operation Doing sowill stop printer operation DO NOT scratch the surface of printed labels or receipt with a sharp object 1 INTRODUCTION EM1 33043D 1 1 APPLICABLE MODEL 1 1 APPLICABLE MODEL e B 210 Series Model name description B 211 GH11 GB Destination GB Great Britain QP Europe QM Other countries Interface 11 Radio 418 MHz RS 232C 12 Radio 433 MHz RS 232C 23 RS 232C 24 RS 232C IrDA Issue mode H Batch Strip mode Dot density of the print head G 8 dots mm NOTE The B 211 GH11 GB model is for exclusive use in Great Britain 1 INTRODUCTION EM1 33043D 1 2 ACCESSORIES 1 2 ACCESSORIES Owner s Manual Print Head Cleaner Battery Media Guide U 2 SPECIFICATIONS EM1 33043D 2 1 PRINTER 2 SPECIFICATIONS 2 1 PRINTER Item Description Dimensions Weight Operating temperature Operating humidity Issue mode Print head Print method Print head dot density Print speed Effective print width Fonts Bar code types Power source 128 mm W x 88 mm H x 50 mm D Approximate 460 g 450 g Including a battery 5 C 40 C 25 85 RH No condensation Batch mode Strip mode Thermal print head Thermal direct 8 dots mm 203 dpi Max 50 8 mm sec 48 mm Standard characters and char
14. nly Failure to do this may cause fire or electric shock e Danger of explosion if the battery is incorrectly replaced Replace the battery only with TOSHIBA TEC Corporation Battery Pack Type B 213 BT 7 2 V 1350 mAh Li ion Discard used batteries according to the manufacturer s instruction e ATTENTION Il ya denger d explosion s il ya remplacement incorrect de la batterrie Remplacer uniquement avec une batterie du m me type ou d un type quivalent recommand par le constructeur Mettre au rebut les batteries usag es conform ment aux instructions du fabricant e Do not disassemble and modify the battery because it has a protection unit init Doing so may break the protection unit causing the battery to heat up burst or burn 1 5 1 INTRODUCTION EM1 33043D e Ifthe battery gets wet dry it completely Using a wet battery may cause fire or electric shock e Be aware of the following precautions when using batteries Otherwise they could heat up burst or burn Do not throw the battery into fire or heat it with a microwave or oven etc E Do not load the battery with the electrodes reversed RW Do notconnect the electrodes with metal objects like wire Do not carry or store the battery along with metal objects such as necklaces hairpins etc Do not stick a needle into hammer step on or drop the battery Do not solder the battery Do not leave the battery where the temperature is more than
15. or IrDA To perform the radio communication or IrDA the printer must be synchronized with the handy terminal IrDA is available on the condition indicated below The following performance is obtained under the fluorescent lamp max 1000 Ix Care must be taken to prevent direct sunlight from coming into the IrDA interface window Handy IST Printer Terminal d 18 5 max 30 cm Printer j max 30 cm ish Handy E Terminal 7 ISSUING THE MEDIA EM1 33043D 7 ISSUING THE MEDIA 1 Turn on the printer 2 Send data from the handy terminal to the printer Regarding the operation of the handy terminal please refer to the handy terminal s operating manual Radio Communication Sample 3 Issuing labels 1 The number of labels are specified when issuing labels in batch mode To re issue the label press the REPRINT button The printer prints labels one by one in strip mode by pressing the REPRINT button To issue more than one label remove the printed label before issuing the next one NOTE Trim off the backing paper coming from the backing paper outlet e 7 2 7 ISSUING THE MEDIA EM1 33043D 7 ISSUING THE MEDIA 3 After printing the receipt press the REPRINT button to feed it to the position where it is easily cut Each time the REPRINT button is pressed the receipt is fed for 20 mm 4 Trim off the printed media upward or downward with the cutter NOTE Do not
16. ought the machine USA only 4 LITHIUM ION BATTERY DISPOSE OF PROPERLY Caution Do not handle damaged or leaking lithium ion battery 1 Slide the battery cover release catch toward the direction indicated by the arrow and open the battery cover Battery Cover Fig 4 1 4 INSTALLING THE PRINTER EM1 33043D 4 1 LOADING THE BATTERY 2 Load a fully charged battery into the printer NOTE Remove the battery pack cover from the battery and then load the battery in the correct orientation as indicated in the following figure Battery Battery Pack Cover j 3 Close the battery cover completely 4 Turn on the printer and the status indicator will blink then go off The status indicator which does not light or stays lit indicates that the battery is uncharged 4 2 4 INSTALLING THE PRINTER EM1 33043D 4 2 INSTALLING THE MEDIA GUIDE 4 2 INSTALLING THE MEDIA GUIDE NOTE The media guide is not required for a 55 mm wide label roll 1 Slide the media cover release catches and open the media cover A cutter is attached to the inside of the media cover Care should be take not to injure your hand with the cutter when opening the cover 2 Fit the media guide into a slot which corresponds to the width of media to be used First insert portion then until it snaps in position 4 3 4 INSTALLING THE PRINTER EM1 33043D 4 2 INSTALLING THE MEDIA GUIDE Unit mm 3 Toremoveor
17. pull the media toward the feed direction as this will misalign the print position of the next media Fig 7 2 7 3 8 CARE HANDLING OF EM1 33043D THE MEDIA 8 CARE HANDLING OF THE MEDIA 8 CARE HANDLING OF THE MEDIA CAUTION Be sure to read carefully and understand the Supply Manual Use only media which meet specified requirements Use of non specified media may shorten the head life and result in problems with bar code readability or print quality All media should be handled with care to avoid any damage to the media or printer Read the following guideline carefully e Do not store the media for longer than the manufactures recommended shelf life e Store media rolls on the flat end do not store them on the curved sides as this might flatten that side causing erratic media advance and poor print quality e Store the media in plastic bags and always reseal after opening Unprotected media can get dirty andthe extra abrasion from the dust and dirt particles will shorten the print head life e Store the media in a cool dry place Avoid areas where they would be exposed to direct sunlight high temperature high humidity dust or gas 8 1 CARE HANDLING OF EM1 33043D THE MEDIA 8 CARE HANDLING OF THE MEDIA The thermal paper used for direct thermal printing must not have the specifications which exceed Ca 800 ppm Na 800 ppm K 800 ppm and CL 600 ppm Some ink used on pre printed labels
18. re Keep the battery away from flame aheat source or other locations subject to high temperature Failure to do this may cause it to over heat or burn Use the specified battery charger only Failure to do this may cause the battery to overheat burst or burn Do not force the battery into the machine or battery charger Doing so may cause the battery to overheat burst or burn Check for the correct electrode Do not connect the battery to a power outlet or acar cigarette lighter jack as this may cause the battery to overheat burst or burn Because the B 213 BT battery is exclusively for the B 210 printer do not use the battery in other machines Doing so may damage the battery or affect the performance and life of the battery 1 8 1 INTRODUCTION EM1 33043D 1 INTRODUCTION Precautions The following precautions will help to ensure that this machine will continue to function correctly Tryto avoid locations that have the following adverse conditions Temperatures below 5 C and above 40 C Direct sunlight Excessive vibration The cover should be cleaned by wiping with a dry cloth or a cloth slightly dampened with a mild detergent solution NEVER USE THINNER OR ANY OTHER VOLATILE SOLVENT on the plastic covers USE ONLY TOSHIBA TEC SPECIFIED media DONOTSTORE the media where they might be exposed to direct sunlight high temperatures high humidity dust or gas Any data stored in the me
19. relocate the media guide push up the pin on the media guide with a screw driver or equivalent and remove the media guide from the printer Media Guide 4 4 5 LOADING THE MEDIA EM1 33043D 5 LOADING THE MEDIA 5 LOADING THE MEDIA A cutter is attached to the inside of the media cover Care should be taken not to injure your hand with the cutter when opening the cover This printer prints both labels and receipts 1 Turn off the printer 2 Slide the media cover release catches in the direction indicated by arrows and open the media cover w Media Cover S 5 1 5 LOADING THE MEDIA EM1 33043D 5 LOADING THE MEDIA 3 Puta label roll or a receipt roll into the media holder unit in the orientation as shown below dl Media Roll e Batch issue 1 Insert the leading edge of the label roll into the media outlet 5 2 5 LOADING THE MEDIA EM1 33043D 5 LOADING THE MEDIA 2 Close the media cover completely Make sure that the media cover release catches snap back into position 3 Turn on the printer and press the REPRINT button The printer will align the print start position for the label When using receipts the printer will feed for 20 mm 5 3 5 LOADING THE MEDIA EM1 33043D 5 LOADING THE MEDIA e Strip issue 1 Unrollthe label roll alittle and remove a label 2 Close the media cover completely Make sure that the media cover release catches snap b
20. termined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help 1 2 1 INTRODUCTION EM1 33043D 1 INTRODUCTION Changes or modifications not expressly approved by manufacturer for compliance could void the user s authority to operate the equipment CAUTION To avoid injury be careful not to catch o jam your fingers while opening or closing the cover CAUTION Do not touch moving parts To reduce the risk that fingers jewelry clothing etc be drawn into the moving parts push the switch in the O position to stop movement Safety Summary Personal safety in handling or maintaining the equipment is extremely important Warnings and Cautions necessary for safe handling are included in this manual All warnings and cautions contained in this manual and written inside or outside of the printer should be read and understood before handling or maintaining the equipment Do not attempt to effect repairs to this equipment If a fault occurs that cannot be rectified using the procedures described in this manual turn off the power then contact your authorise
21. y onto the printer 9 2 COVERS AND OPERATION PANEL The covers should be cleaned by wiping with a dry cloth or acloth slightly dampened with a mild detergent solution NOTE Clean the printer cover with an electrostatic free cleaner for automated office equipment CAUTION DO NOT POUR WATER directly onto the printer DONOTAPPLY cleaneror detergent directly onto any cover or panel NEVER USE THINNER OR OTHER VOLATILE SOLVENT on the plastic covers DO NOT clean the covers or the operation panel with alcohol as it may cause them to discolor loose their shape or develop structural weakness 9 GENERAL MAINTENANCE EM1 33043D 9 3 REMOVING JAMMED MEDIA 9 3 REMOVING JAMMED MEDIA Turn off the printer Open the media cover Remove the media roll from the printer Ron Remove the jammed media DO NOT USE any sharp implement or tool as these could damage the printer 5 Clean the print head and platen then remove any further dust or foreign substances 9 4 10 TROUBLESHOOTING EM1 33043D 10 TROUBLESHOOTING 10 TROUBLESHOOTING If you cannot solve a problem with the following solutions do not attempt to repair it yourself Turn off the printer then contact your TOSHIBA TEC representative for assistance When a problem occurs during operation the status indicator will blink or light Refer to the following troubleshooting guide and take corrective action Status Ind
Download Pdf Manuals
Related Search