Home
Top Innovations SF-475 Iron User Manual
Contents
1. Do not try to add any more Reservoir fill hole when full water adding water Water Reservoir is too hot to Allow more cooling time be refilled before refilling Fill Water Reservoir more slowly Be sure to utilize the provided Measuring Cup and Water Funnel to refill the unit Accessories do not stay Accessories are not being Review steps for proper firmly attached to Steam properly installed installation of accessories on Nozzle page 7 of this manual Check to ensure that accessories are installed correctly Accessories or Steam Nozzle Contact our Customer is damaged or otherwise Service Department for incorrect assistance CUSTOMER SUPPORT For problems with your Fabric Steamer please refer to the troubleshooting solutions located on pages 12 amp 13 of this manual Additional inquiries should be directed to our Customer Support services through our Web site www steamfast com on the Service Request Web page If you do not have internet access you may also contact our Customer Support Department by telephone at 800 711 6617 or 816 584 9700 NOTE In order for our customer service representatives to help you as quickly and efficiently as possible please have the following information ready before calling Purchase information where and when you purchased this product e Product Serial Number Top Innovations Inc ONLINE ORDERING Try our secure and convenient online ordering system through our
2. leak LJ tL FIGURE 5 FIGURE 6 FIGURE 7 ATTACHING LINT REMOVER FABRIC BRUSH CLOTH COVER 1 Make sure Lighted On Off Switch is set to Off position and that unit is not emitting any steam Do not try to connect Lint Remover Fabric Brush or Cloth Cover while unit is emitting steam as this can cause burns and injury Align two pegs on back of accessory with corresponding holes on face of Steam Nozzle Use care to properly align attachment as shown FIGURE 8 so as not to cover up steam holes on nozzle face 3 Press accessory firmly onto Steam Nozzle until it fits securely in place N FIGURE 8 Top Innovations Inc l USING THE FABRIC STEAMER FILLING WATER RESERVOIR WITH WATER Place Fabric Steamer on a flat level surface 2 Make sure Lighted On Off Switch is set to Off position and grounded power cord is unplugged from electrical outlet 3 Flip up Compartment Lid Cautiously unscrew and remove Water Reservoir Cap 4 Water Reservoir should always be emptied after each use If it was not emptied after the last use empty it now This will prevent over filling 5 Fill Measuring Cup to maximum fill line 16 oz 473 ml with water NOTE To prolong the life of your Fabric Steamer we recommend using distilled or de mineralized water 6 Using Water Funnel carefully pour water from Measuring Cup into Water Reservoir through fill hole WARNING Extreme caution should b
3. limited warranty you will be advised of the cost of repair before any servicing is done unless you enclose a note indicating that you would like us to proceed with repairs If you need to request warranty service or have any questions about coverage under this warranty please visit the Warranty Service Request page on our Web site www steamfast com You may also contact the Warranty Service Department by telephone at 800 711 6617 or 816 584 9700 or e mail customerservice topinnovations com Please have your product serial number ready before contacting Warranty Service Department The serial number is located on the back or bottom of your unit Top Innovations Inc 15 Steam osi Top Innovations Inc 6655 Troost Ave Kansas City MO 64131 Tel 800 711 6617 816 584 9700 www steamfast com customerservice topinnovations com Printed in China PRODUCT SERIAL NUMBER For your convenience space has been provided below for you to record the serial number of your unit located on the back or bottom of the unit for easy reference when contacting our Customer Service Department V051213
4. website MODEL SF 475 14 www steamfast com ACCESSORY ORDER FORM PART PART DESCRIPTION PRICE QTY TOTAL anor aback f a amon irem id Asan ewe vind A275 004 Water Funnel A400 010 Press Pad SF 475 Accessory Kit A special value of only 49 99 7 99 S amp H Transforms the SF 475 from a garment steamer into a powerful steam cleaner A475 K1 Includes 172 Steam Cleaning Hose 5 Assorted Utility Brushes Brass Utility Brush 2 Extension Wands 1 Triangle Brush 1 Floor Brush 1 Cloth Towel SHIPPING AND HANDLING 3 99 7 99 for A475 K1 1 Scrub Pad 1 Squeegee TOTAL USD Note that 3 99 S amp H applies to the A420 001 A420 002 A420 003 A275 003 A275 004 and A400 010 7 99 S amp H applies only to A475 K1 These charges apply to shipping in the continental United States only METHOD OF PAYMENT no C O D orders TO ORDER C Check or Money Order payable to Top Innovations ONLINE Visit www steamfast com Charge to my _ visa MASTERCARD BY MAIL Fill out this form and return to Top Innovations Inc Kansas City MO 64131 ACCOUNT NUMBER LITT EXPIRATION DATE NAME PRINTED MAILING ADDRESS BY PHONE 800 711 6617 or 816 584 9700 BY FAX 816 584 9066 TELEPHONE SIGNATURE Full Name as Shown on Account PRODUCT SERIAL NUMBER Serial Number is Required to Process Order Top Innovations Inc WARRANTY INFO
5. MODEL SF 475 Steam ASi Fabric Steamer by Top Innovations Inc Please read all instructions before use Mail in your warranty registration card LETTER FROM THE CEO Dear Valued Customer Congratulations on purchasing your new SF 475 Fabric Steamer This powerful product is designed to effectively smooth wrinkles and reduce odors with a minimum of time and effort Turn your Fabric Steamer on and in minutes you are ready to delicately remove wrinkles from garments draperies and upholstery With 1500 Watts of power and a 48 oz 1420 ml maximum water capacity this Fabric Steamer is capable of handling everything from big steaming jobs to quick touch ups Steam everything from clothing hung conveniently on the attached Clothes Hanger Hook to drapes that are still hanging without the hassle of taking them down The all natural chemical free wrinkle removing power of steam combined with its ability to reduce smoke pet and other unpleasant odors means that the Fabric Steamer will let you care for your precious fabrics and garments the way you ve always wanted to Top Innovations Inc would like to invite you to visit our Customer Support Web site www steamfast com On this Web site you will find additional information about many other exciting products that are available helpful tips on ways in which you can utilize your Fabric at Steamer and other useful information to assist you in maximizing the po
6. On position 3 Steam Ready Light will illuminate while boiler is FIGURE 10 heating When Steam Ready Light deactivates 2 8 minutes depending on amount of water in Water 4 Reservoir unit will automatically begin emitting steam Place garment on a clean rust free clothes hanger Place hanger with garment on Clothes Hanger Hook ZTN FIGURE 10 f N CAUTION Use care when handling garments on the Clothes Hanger Hook Pulling on the garment with too much force may cause the unit to tip over 6 Direct Steam Nozzle towards bottom of garment Steam will rise along inside and outside of fabric removing wrinkles Slowly slide Steam Nozzle vertically from bottom to top of garment FIGURE 11 NOTE Do not allow kinks to form in hose at any time during use 7 Direct Steam Nozzle away from garment and smooth n amp fabric with your free hand E t t 8 Repeat steps 6 amp 7 as necessary until fabric is smooth and wrinkle free gt OTHER STEAMING TIPS FIGURE 11 e Curtains and draperies may be steamed while still hanging e To remove wrinkles from towels handkerchiefs and napkins drape them over a rod or towel rack and gently steam them e Heavier fabrics may require repeated steaming to effectively remove wrinkles e To remove exceptionally stubborn wrinkles steam both sides of fabric e For additional assistance in removing tough wrinkles or to remove lint and other particles attach Fabric Brush or Lint Remove
7. RMATION ONE YEAR LIMITED WARRANTY If outside USA additional shipping charges may apply Top Innovations Inc warrants this product to be free from defects in material and workmanship for a period of one 1 year from the date of purchase This warranty does not cover damage caused by misuse negligence use by improper current or voltage commercial use use contrary to operating instructions or disassembly repair or alteration by any person other than Top Innovations Inc Warranty Service Department Top Innovations Inc will repair or replace at its option This warranty gives you specific legal rights and may have other rights which may vary from state to state Performance of any obligation under this warranty may be obtained by 1 Call 800 711 6617 for Return Authorization Number before returning for repair Failure to obtain a Return Authorization Number will cause a delay in warranty and out of warranty service requests 2 Include copy of purchase receipt 3 Include your name address telephone number and Return Authorization Number on returned package Please send product postage prepaid to TOP INNOVATIONS INC WARRANTY SERVICE DEPARTMENT 6655 TROOST AVE KANSAS CITY MO 64131 Should there be any missing or defective parts or accessories please contact Customer Support In most cases it is not necessary to return the entire unit We can ship most parts directly to your door Upon expiration of 1 year
8. Water Reservoir DO NOT lay Hose on floor 12 Use caution as burns could occur from touching hot metal parts hot water or steam 13 SF 475 Fabric Steamer is only meant to be used with recommended SF 475 accessories Other types of attachments are not to be used with Fabric Steamer Doing so may cause injuries or damage to unit 14 Nozzle and attachments become hot during use To avoid injuries DO NOT touch nozzle while using this appliance DO NOT attempt to change attachments while unit is emitting steam 15 When filling your Fabric Steamer only water should be used in unit Other cleaning agents will damage unit and can cause injuries 16 DO NOT operate unit if steam opening is blocked Should this occur immediately cease usage and unplug from electrical outlet 17 Store your SF 475 Fabric Steamer in a cool dry place SAVE THESE INSTRUCTIONS FOR HOUSEHOLD USE ONLY Top Innovations Inc FABRIC STEAMER PRODUCT INFORMATION The following features and accessories are included with your Steam Cleaner Carefully inspect packaging material as some parts are shipped inside Styrofoam packaging To obtain possible missing parts refer to the Customer Support section on page 13 of this manual UNIT FEATURES amp ACCESSORIES Pole Top Steam Nozzle Holder Clothes Hanger Hook Steam Nozzle Handle Telescopic Pole Pole Base Hose Hose Base Steam Ready Light Lighted On Off Switch Water Reservoir Sto
9. e a risk of fire electrical shock or injury to persons when steamer is used To reduce risk of electrical shock DO NOT immerse in water or other liquids DO NOT use electrical cord or Hose as a handle DO NOT allow cord or Hose to be crimped by closing it in doors DO NOT pull or stretch cord or Hose around sharp corners or edges Before filling unit with water always unplug power cord from electrical outlet Failure to do so may result in electrical shock and injury Do not allow electrical cord to touch hot surfaces Let appliance cool completely before putting away Loop cord loosely around appliance when storing DO NOT use this unit with extension cords or electrical outlets that have inadequate current capacity A three prong outlet or a properly grounded adapter is necessary when using SF 475 Fabric Steamer SAVE THESE INSTRUCTIONS FOR HOUSEHOLD USE ONLY Top Innovations Inc IMPORTANT SAFEGUARDS WARNING To reduce the risk of electrical shock this appliance has a three pronged plug This plug will fit in a polarized wall outlet only one way If the plug does not fit fully in the outlet contact a licensed electrician to install a proper outlet DO NOT attempt to modify the plug or defeat this safety feature 10 In order to unplug SF 475 Fabric Steamer grasp plug and pull smoothly and firmly from outlet DO NOT attempt to unplug unit by pulling or tugging on cord 11 Always keep Steam Nozzle elevated above
10. e used when pouring water into the Water Reservoir Do not look directly down into fill hole when filling Keep your free hand and any children or pets at a safe distance 7 Depending on how long you intend to steam you may repeat steps 5 amp 6 up to two more times to a maximum of 48 oz 1420 ml of water See chart below for a comparison of the amount of water vs approximate steam time 16 oz 473 ml Approximately 15 min 32 oz 946 ml Approximately 30 min 48 oz 1420 ml Approximately 45 min 8 Replace Water Reservoir cap ensuring that it is screwed on tightly to prevent hot steam from escaping and causing injury 9 Lower Compartment Lid back down IMPORTANT When steamer is first activated it is natural for it to spray small amounts of water This is due to condensation forming in the Hose and will dissipate within 30 seconds of use To help clear condensation out of Hose more quickly try the following e Point Steam Nozzle towards ground sink or tub and shake it to force water out of Hose e Extend Hose vertically as far as possible to allow water to drain back into Water Reservoir Top Innovations Inc USING THE FABRIC STEAMER NOTE Be sure that any desired attachments are connected and Water Reservoir is filled before following f these steps ZES OPERATING THE FABRIC STEAMER tah 1 Plug grounded power cord into a convenient 3 prong electrical outlet 2 Switch Lighted On Off Switch to
11. f water 16 48 oz in the Water Reservoir in order for the unit to properly function e The Storage Compartment 9 provides a convenient place to store small accessories The Water Reservoir Cap 9a is located inside the Storage Compartment and must be removed in order to expose the fill hole and fill the Water Reservoir with water The Compartment Lid 9b is a hinged lid that covers the Storage Compartment and Water Reservoir Cap e The Lint Remover 10 connects to the Steam Nozzle and is designed to assist in removing lint loose threads and other small particles from fabric e The Fabric Brush 11 connects to the Steam Nozzle and is designed to assist in smoothing out exceptionally stubborn wrinkles e The Cloth Cover 12 is connects to the Steam Nozzle and is useful for preventing large water droplets from dripping on delicate materials e The Measuring Cup 13 and Water Funnel 14 are provided to assist you in easily and consistently filling the Water Reservoir with the optimum amount of water 16 48 oz 473 1420 ml The Press Pad 15 fits on your hand allowing you to support the fabric for a more thorough steaming The Press Pad also protects your hand from being burned by hot steam Top Innovations Inc ATTACHING THE TELESCOPIC POLE 1 Attach Pole Top by sliding it onto top of Telescopic Pole as shown FIGURE 1 Note that Pole Top must align correctly in two grooves that run the length of pole 2 Line up gro
12. nate Steam output is intermittent Unit is emitting excess water Excessive gurgling in Hose and Steam Nozzle water drips from Steam Nozzle Household Circuit Breaker Ground Fault Interrupter has tripped or blown a fuse Water Reservoir is empty Mineral build up in unit Mineral build up in unit Water condensation in Steam Hose Water Reservoir has been over filled Unit has not reached operating temperature Condensation in Steam Hose Top Innovations Inc Reset Circuit Breaker Ground Fault Interrupter or replace fuse If you need assistance contact a licensed electrician Refill Water Reservoir using procedures on page 9 of this manual Follow Removing Mineral Build Up procedure on page 11 of this manual It is normal for unit to periodically stop steaming for a few seconds If steam stays off for longer periods follow Removing Mineral Build Up procedure on page 11 of this manual Point Steam Nozzle towards sink tub or ground and shake Continue until excess water is released Empty some water out of Water Reservoir Wait until Steam Ready Light deactivates to steam Some gurgling is a natural effect of steaming process For excessive gurgling or dripping water extend Hose vertically to allow water to drain back into Water Reservoir TROUBLESHOOTING amp CUSTOMER SUPPORT PROBLEM POSSIBLE CAUSE SOLUTION Water spills out from Water Water Reservoir is already
13. oves of Telescopic Pole with two tabs inside Pole Base hole and insert bottom section of Pole into Base FIGURE 2 3 Tighten knob by turning it in a clockwise direction until it is tight and Telescopic Pole sits firmly in place in the Pole Base FIGURE 3 FIGURE 1 FIGURE 2 FIGURE 3 EXTENDING TELESCOPIC POLE 1 Locate bottom extension lock and swing hinge outward as shown FIGURE 4 Extend middle section of Telescopic Pole as far upward as it will go then close hinge to relock bottom extension lock 2 Repeat Step 1 for remaining two extension locks until Telescopic Pole is extended to it s full height Ra NOTE Itis recommended to extend Telescopic Pole to it s full height during steamer operation This ensures full extension of Steam Hose for maximum flow of steam FIGURE 4 Top Innovations Inc 7 CONNECTING HOSE 1 Slide Hose fitting onto threaded Hose Base FIGURE 5 2 Turn Hose fitting clockwise to secure it to Hose Base FIGURE 6 NOTE Hand tighten Hose fitting only Do not over tighten 3 Hang Steam Nozzle on specially designed Steam Nozzle Holder as shown FIGURE 7 CAUTION To prevent steam from causing bodily injury or damage to surfaces always hang Steam Nozzle on Steam Nozzle Holder when not in use Do not lay Hose on floor as condensation may build up inside causing unwanted water droplets in steam CAUTION Pulling on Hose with excessive force may damage it resulting in a steam
14. r to Steam Nozzle see Attaching Lint Remover and Fabric Brush section on page 8 of this manual e Use Press Pad in order to steam difficult spots and edges and to create creases in fabric Slide your hand through the velcro strap on back of Press Pad to secure it to your hand This will protect your hand from the flow of hot steam Then steam fabric while pressing it firmly but gently against the Press Pad 9 When you have completed your steaming tasks immediately switch Lighted On Off Switch to Off position and unplug power cord from electrical outlet Refer to Proper Storage section on page 11 of this manual for information on proper cleaning and storage of Fabric Steamer 10 Top Innovations Inc j CARE amp STORAGE GUIDELINES PROPER STORAGE Preparing your Fabric Steamer for storage is quick and simple When you have fin ished your steaming tasks follow the steps listed below 1 Unplug grounded power cord from electrical outlet Allow unit to cool completely at least 30 minutes 2 3 4 Remove all attachments from unit Drain any remaining water in Water Reservoir into a sink or tub to prevent over filling during your next use Unhook three extension locks on Telescopic Pole and press down on Pole Top to collapse Pole into compact storage position Re lock extension locks Wrap Hose loosely around Telescopic Pole one time and hang Steam Nozzle from Steam Nozzle Holder Store all attachments
15. rage Compartment Water Reservoir Cap Compartment Lid Lint Remover Fabric Brush Cloth Cover Measuring Cup Water Funnel Press Pad Top Innovations Inc FABRIC STEAMER PRODUCT INFORMATION The Pole Top 1 is comprised of the Steam Nozzle Holder la and the Clothes Hanger Hook 1b The Steam Nozzle Holder provides a safe and convenient place to hang the Steam Nozzle The Clothes Hanger Hook allows you to steam garments that are hanging from a clean rust free hanger e The Steam Nozzle 2 is designed to spread hot penetrating steam over a wide area The Handle 3 is designed to stay relatively cool while providing the optimum amount of safety and user comfort e The Telescopic Pole 4 connects the Pole Top to the steamer and collapses to allow quick compact storage of the unit The Pole Base 4a is the mount where the Telescopic Pole connects to the main unit body e The Hose 5 safely channels steam from the boiler to the Steam Nozzle The Hose Base 5a is the mount where the Hose connects to the main unit body e The Steam Ready Light 6 indicates when the unit is ready to steam by lighting up during heating and turning off when the steam is ready e The Lighted On Off Switch 7 turns the unit on and off and provides a clear visual indication when the steamer is turned on e The Water Reservoir 8 is where water is stored for use by the unit There must be a sufficient amount o
16. safely away preferably inside Storage Compartment or near Fabric Steamer Store Fabric Steamer in a cool dry location REMOVING MINERAL BUILD UP A common problem with steam appliances is mineral build up caused by high mineral content in many municipal water supplies The best way to avoid this is to use de mineralized or distilled water in unit If you are unable to use de mineralized or distilled water we recommend you use this procedure monthly to help avoid mineral build up 1 NAWN eons Switch Lighted On Off Switch to Off position and unplug grounded power cord from electrical outlet Allow unit to completely cool Remove all accessories from unit Flip up Compartment Lid and remove Water Reservoir Cap Drain water from Water Reservoir into sink or tub Using Measuring Cup make a mixture of 8 oz 236 ml vinegar and 8 oz 236 ml water Slowly pour water vinegar solution into Water Reservoir Allow to stand for 40 minutes Drain water vinegar solution from Water Reservoir Rinse Water Reservoir with fresh water drain and repeat until vinegar odor dissipates 10 Replace Water Reservoir Cap and lower Compartment Lid back down Top Innovations Inc 11 TROUBLESHOOTING GUIDE PROBLEM POSSIBLE CAUSE SOLUTION Unit is not plugged in Plug into electrical outlet Unit fails to steam Lighted On Off Switch does not illuminate Unit fails to steam Lighted On Off Switch does illumi
17. wer of steam Enjoy your new SF 475 Fabric Steamer a Benny Lee Chairman and CEO Top Innovations Inc Top Innovations Inc IMPORTANT SAFEGUARDS WARNING To reduce the risk of fire electrical shock or injury the following basic safety precautions should always be followed when using an electrical appliance N A mn READ ALL INSTRUCTIONS BEFORE USING YOUR FABRIC STEAMER Unit Water Reservoir is designed to hold a maximum of 48 oz 1420 ml of water Use caution when filling to avoid burns from spilling water or possible electrical shock DO NOT leave your SF 475 Fabric Steamer unattended when plugged in or not in use Use only for its intended purpose as indicated in this manual this unit is not a toy Close supervision is required when using unit near children pets and plants Steam produced by unit is hot and pressurized Care must be taken to avoid burns or other injuries Never point nozzle at people or pets To reduce the risk of contact with hot water emitting from steam vents hold appliance away from body and check for signs of condensation or leakage DO NOT use this unit if electrical cord or outlet is damaged DO NOT use unit if it is not working properly or has been dropped damaged or left outdoors If such damage occurs DO NOT disassemble or attempt repairs take unit to a qualified service person for examination and repair Incorrect reassembly or repair could caus
Download Pdf Manuals
Related Search
Related Contents
Samsung Galaxy Note pro (12.2) manual do usuário(OPEN) Chamberlain 985 Garage Door Opener User Manual Cover Page User Guide 2013 Dodge Charger SRT User`s Guide InFocus IN5124 User's Manual User modeling as machine identification: new design methods for HCI 取扱説明書 保管用一 Lorex SG7550 Series User's Manual - FABTVI*710 AKTION Batterie Visonic Funksirene Batterie Spin-Klin GALAXY 4" Manuel de Service & Maintenance. Copyright © All rights reserved.
Failed to retrieve file