Thermador 9000039271 Dishwasher User Manual
Contents
1. 508mm above the cabinet floor 11 HOT WATER CONNECTION 12 AX WARNING SCALD HAZARD Working on a Charged hot water line could result in serious injury or death Do not attempt any work on the dishwasher hot water supply plumbing until you are certain the hot water supply is shut off NOTE Make certain that the correct 90 elbow fitting not supplied for the hot water supply line has been purchased and installed on the dishwasher as described in the Dishwasher Preparation section of this manual The hot water supply line may be connected to the dishwasher in one of two ways 1 With braided hose 2 With copper tubing Braided Hose After connections are made turn on the hot water supply to check for leaks Copper Tubing CAUTION Temperatures required for soldering and sweating will damage the dishwasher s water inlet valve If plumbing lines are to be soldered or sweated keep the heat source at least 6 inches 152 4 mm away from the dishwasher s water inlet valve e If using a solder joint instead of a compression fitting be sure to make all solder connections before connecting the water line to the dish washer e Make certain there are no sharp bends or kinks in the water line that might restrict water flow e Be sure to use pipe thread compound or Teflon tape to seal the connection when required Before connecting the copper hot water supply line to the dishwasher flush it with hot water to2. clear any foreign material Turn on the water supply to check for leaks after making connections ELECTRICAL CONNECTION Strain F not suf Figure 24 Figure 25 AX WARNING ELECTRICAL SHOCK HAZARD Working on an energized circuit could result in serious injury or death Only qualified electricians should perform electrical work Do not attempt any work on the dishwasher electric supply circuit until you are certain the circuit is de energized AX WARNING FIRE HAZARD Improper electrical work can cause fire Only qualified electricians should perform electri cal work Grounding Instructions The dishwasher must be properly grounded before operating This appliance must be connected to a grounded metal permanent wiring system or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment grounding terminal or lead on the dishwasher Make sure that the dishwasher is connected to a suitable ground in compliance with all local codes or in the absence of a local code with the NATIONAL ELEC TRICAL CODE in the United States or the CANADIAN ELECTRIC CODE C22 1 latest edition in Canada as well as any provincial state or municipal or local codes that apply 1 Retrieve the strain relief plate and install a strain relief not supplied into the opening on the strain relief plate NOTE Orient the strain relief as shown in Figure 24 2 Pass the electrical supply cable th
3. insulation from each conductor as shown in Figure 6 letter D Dishwasher Electrical Rating Vons ertz amperes watts max PLUMBING PREPARATION Figure 7 4 amp WARNING SCALD HAZARD Serious injury could result if work is performed on a charged hot water line Only qualified plumbers should perform plumbing work Do not attempt any work on the dishwasher hot water supply plumb ing until you are certain the hot water supply is shut off CAUTION Temperatures required for soldering and sweating will damage the dishwasher s base and water inlet valve If plumbing lines are to be soldered or sweated keep the heat source at least 6 inches 152 4 mm away from the dishwasher s base and water inlet valve Hot Water Supply The hot water heater should be set to deliver approximately 120 F 49 C water to the dish washer Water that is too hot can cause some detergents to lose effectiveness Lower water temperatures will increase run times The hot water supply pressure must be between 15 145 psi 1 10 bars Hot Water Supply Plumbing Install an easily accessible shut off valve not supplied in the hot water supply line as shown in Figure 7 letter B All solder connections must be made before the water line is connected to the dishwasher s water inlet valve Water may also be supplied to the dishwasher by using a braided hose line Check with your local plumbing supply sources for the prope
4. items that come with the original package until after the entire installation has been completed TOOLS NEEDED Tape Pipe Adjustable Wrench Wrench Slot Phillips Torx Measure Screwdriver Screwdriver Screwdriver Wire Stripper MATERIALS NEEDED Additional materials may be required to comply with local codes Electrical Supply Cable Minimum 14 AWG 2 conductor 1 ground insu lated copper conductors Hot Water Supply Line Minimum 3 8 O D copper tubing or metal braided dishwasher supply line Shut off valve and fittings appropriate for hot water supply line copper tubing compression fitting or braided hose 90 elbow with 3 8 N P T male threads on one leg and sized to fit your water supply line copper tubing compression fitting or braided hose on the other leg Teflon tape or other pipe thread compound to seal plumbing connections UL listed conduit connector or strain relief MATERIALS SUPPLIED 4a C1 o o K _ Ow S Figure 1 Accessory Parts Supplied Accessory Parts for your dishwasher will come in one or more plastic bags Check to make sure that the parts shown in Figure 1 are included with your model If any parts are missing contact your dealer immediately NOTE Illustrations are not to scale Manual Set Bag This dishwasher comes with a Manual Set Bag containing e Use amp Care Instructions and Installation Instructions e Qu
5. you are writing please include a daytime phone number where you can be reached You will find the model and serial number information on the label located on the right hand side of the inner door of your dishwasher It will look similiar to this Gat Sarka 883 735 4328 Otay wv BBA ak DWAA7S 6 Mow op whw Pr q wen m cine To Marana til fee 00224 i Kanker USA es ki k g 2 DRADER y aL wdaggnanqng74 1 A Please make a copy of your invoice and keep it with this manual 16
6. 1 2 gt lt 8mm 13mm Figure 6 AX WARNING ELECTRICAL SHOCK HAZARD Working on an energized circuit could result in serious injury or death Only qualified electricians should perform electri cal work Do not attempt any work on the dishwasher electric supply circuit until you are certain the circuit is de energized WARNING FIRE HAZARD Improper electrical work can cause fire Only qualified electricians should perform electrical work Electrical Supply The customer has the responsibility of ensuring that the dishwasher electrical installation is in compli ance with all national and local electrical codes and ordinances The dishwasher is designed for an electrical supply of 120V 60 Hz AC connected to a dishwasher dedicated properly grounded electrical circuit with a fuse or breaker rated for 15 amps If the dishwasher is connected with a food disposer a 20 amp and no higher fuse or circuit breaker may be used Electrical supply conductors shall be a minimum 14 AWG copper wire Regardless of where the electrical supply cable enters the enclosure following the guidelines on page 8 position the cable 21 583mm from the enclosure s left side as shown in Figure 5 letter A Extend the cable 30 762mm from the enclosure s back as shown in Figure 5 letter B Remove 3 4 75mm 100mm of the cable s outer casing as shown in Figure 6 letter C then remove 3 8 1 2 9 18mm of
7. Thermador 24 Anerican Jon DISHWASHER INSTALLATION INSTRUCTIONS Table of Contents IMPORTANT INSTRUCTIONS cee 1 Tools Needed onae a a as nate 2 Materials Needed cccsscecseeecsseeeeeseeseeens 2 Materials Supplied ccccceeceesseeeeeeeeeeeeeeeees 3 Enclosure Preparation oannnanenennnannnnnnnnnenenne 4 Electrical Preparalo n a e e a a re 5 Plumbing Preparation cccsccecssseeeseeeeeens 6 7 Dishwasher Preparation ccsssceseseeeees 7 8 Door Panel MlinStetl atl Nissseseseese eee eee te 9 Placing the Dishwasher lt tce cracn sesserereaeceeescees 10 Securing the Dishwasher ccccccsssseeeeees 10 Drain Hose Connection sasoenenenennnennnennnennrnnn 11 Hot Water Connection ccecceeceeeeeeeeeeeeeeee 12 Electrical GOnmectione ccc c eee eee eee 13 14 Door Tension Adjustment ccccssseeeseees 14 Base and Toe Panel ccceceeeececeeeeeees 14 15 Final Instructions cceccecececeececeeeeeececeseeeees 15 Customer Service a ee ee ee ere 16 IMPORTANT INSTRUCTIONS A WARNING OBSERVE ALL WARNINGS AND CAUTIONS These instructions are intended for use by qualified installers only In addition to these instructions the dishwasher shall be installed e n accordance with all local codes or in the absence of a local code e In the United States with the National Electric Code e In Canada with the Canadi
8. an Electric Code C22 1 latest edition Provincial and Municipal codes and or local codes Read these installation instructions completely and follow them carefully They will save you time and effort and help to ensure safety and optimum dishwasher performance CAUTION If the dishwasher is installed in a location that experiences freezing temperatures e g in a holiday home you must drain all the water from the dishwasher s interior Water system ruptures that occur as a result of freezing are not covered by warranty P N 9000039271 8408 IMPORTANT e The dishwasher drain hose must be installed with a portion of it at least 20 508mm off the cabinet floor otherwise the dishwasher may not drain properly This dishwasher is intended for residential use only and should not be used in commercial food service establishments NEW INSTALLATION If the dishwasher is a new installation most of the work must be done before the dishwasher is moved into place REPLACEMENT If the dishwasher is replacing another dishwasher check the existing dishwasher connections for compatibility with the new dishwasher and replace parts as nec essary Inspect the Dishwasher After unpacking the dishwasher and prior to instal lation thoroughly inspect the dishwasher for possible freight or cosmetic damage Report any damage immediately Cosmetic defects must be reported within 5 days of installation NOTE Do not discard any bags or
9. ay from the dishwasher Set the toe panel aside It will be reinstalled later DWHD94BP and DWHD94BS Base and Toe Panel The base and toe panel are in place on the dishwasher but are not attached Remove the toe panel first as shown in Figure 12 letter A then remove the base as shown in Figure 12 letter B Installing the 90 Elbow Fitting NOTE The 90 elbow fitting is not supplied with the dishwasher and must be purchased separately If the dishwasher s hot water supply line is to be copper tubing make certain the elbow has a compression fitting Apply Teflon tape or other pipe sealant when required Orient the hot water supply connection leg of the elbow toward the channel opening in the dishwasher base Junction Box Preparation 1 Remove junction box cover Figure 13 by lifting the junction box cover up and off 2 Remove the strain relief plate by removing the screw at the back of the junction box as shown in Figure 14 letter D and sliding the strain relief plate out 3 Set the junction box cover strain relief plate and screw aside They will be re installed later DOOR PANEL INSTALLATION Figure 15 DWHD94BF Panel Installation DWHD94BF models come with additional mounting hardware and a template sheet that will show you how to mount the panel One side of the template shows how to mount a one piece panel the other side shows how to mount a two piece panel Decide which type of installat
10. er does not operate properly refer to the Self Help section of the Use and Care Manual If the dishwasher still does not operate properly refer to the Customer Service Section of the Use and Care Manual 15 CUSTOMER SERVICE Your Thermador dishwasher requires no special care other than that described in the Care and Cleaning section of the Use and Care Manual If you are having a problem with your dishwasher before calling for service please refer to the Self Help section of the Use and Care Manual If service is necessary contact your dealer or installer or an authorized service center Do not attempt to repair the appliance yourself Any work performed by unauthorized personnel may void the warranty If you are having a problem with your Thermador dishwasher and are not pleased with the service you have received please take the following steps in the order listed below until the problem is corrected to your satisfaction 1 Contact your installer or the Thermador Authorized Service Contractor in your area 2 E mail us from the customer service section of our website www thermador com 3 Write us at Thermador 5551 McFadden Avenue Huntington Beach CA 92649 4 Call us at 1 800 735 4328 Please be sure to include if you are writing or have available if you are calling the following information Model number Serial number Date of original purchase Date the problem originated Explanation of the problem Also if
11. gure 19 letter B for Side mount DRAIN HOSE CONNECTION Figure 22 Figure 23 The dishwasher drain hose may be connected to the drain plumbing in one of four ways 1 Directly to the undersink dishwasher drain connection as shown in Figure 20 2 Directly to a disposer dishwasher drain connec tion as shown in Figure 21 3 To the undersink dishwasher drain connection through an air gap as shown in Figure 22 4 To a disposer dishwasher drain connection through an air gap as shown on Figure 23 Information on installing air gaps and disposers can be found in the Plumbing Preparation section of this manual NOTE If the dishwasher drain hose is to be con nected to a disposer dishwasher drain connection remove the plug from the disposer s dishwasher drain connection Use the supplied Rubber Connection Hose and Drain Hose Clamps letter G in the Materials Supplied section of this manual to connect the dishwasher drain hose to the plumbing drain connection Use the spring clamp to secure the Rubber Connection Hose to the dishwasher drain hose Use the screw clamp to secure the Rubber Connection Hose to the plumbing drain connection If the dishwasher drain hose is connected directly to either an undersink dishwasher drain connection as shown in Figure 20 or to a disposer dishwasher drain connection as shown in Figure 21 forma curve in the dishwasher drain hose and secure a portion of the curve at least 20
12. ick Reference Guide e Extra Tall Item Sprinkler Fig 1 letter A DWHD94BF also has SHI SHV a Panel Installation Template Sheet Figure 1 letter B DWHD94BP and DWHD94BS also have a Cotton Insulation Strip Figure 1 letter C Dishwasher Installation Kit This dishwasher comes with a Dishwasher Installa tion Kit containing D Toe Panel Screws 2 E Mounting Brackets 2 F Mounting Bracket Screws 2 G Rubber Connection Hose 1 and Drain Hose Clamps 2 H Wire Nuts 3 Junction Box Screws 2 DWHD94BF In addition to a Manual Set Bag and an Installation Kit Bag DWHD94BF models also come with a Door Panel Installation Kit containing J Caps 2 K Spring Tension Screw 2 L Door Mounting Brackets 2 plastic w Screws 4 Mounting Door Brackets 2 metal w Screws 4 M Wood Screws 2 DWHD94BP and DWHD94BS In addition to a Manual Set Bag and an Installation Kit Bag these models also come with a Toe Panel Installation Kit containing N Toe Panel Screws 2 O Base Part Screws 2 ENCLOSURE PREPARATION 23 9 16 598mm 34 864mm minimum 23 5 8 24 1 4 600 616 mm Figure 2 Figure 3 23 5 8 24 1 8 600mm 613mm aioe 89mm 1 5 16 33mm Figure 4 NOTE This dishwasher is designed to be e
13. if the door falls open the spring tension needs to be adjusted To Adjust the Spring Tension 1 Obtain the provided Door Tension Screws Figure 1 letter K from the DWHD94BF parts bag 2 Insert the screws as shown in Figure 27 Turning the screw clockwise increases the spring tension Turning the screws counter clockwise decreases the spring tension BASE AND TOE PANEL Regular Toe Panel Installation Use the toe panel screws Figure 1 letter D from the Dishwasher Installation Kit and a Torx screw driver to install the toe panel as shown in Figure 28 Continued on next page BASE AND TOE PANEL Continued Figure 29 DWHD94BP and DWHD94BS Base and Toe Panel Installation 1 Place the Base Part under and up the front bottom panel of the dishwasher as shown in Figure 29 2 Insert the Base Part screws Figure 1 letter O into the Base Part as shown in Figure 29 letter B Tighten the Base Part Screws 3 Place the Cotton Insulation Strip Figure 1 letter C under the unit between the bottom of the Base Part and the floor as shown in Figure 29 letter C 4 Place the toe panel over the Cotton Insulation Strip and use the toe panel screws Figure 1 letter N to secure the toe panel in place as shown in Figure 29 letter D FINAL INSTRUCTIONS 1 Energize the dishwasher power supply circuit 2 Consult the Dishwasher Use and Care Manual and run the dishwasher through one complete cycle If the dishwash
14. ion you want before proceeding with the installation See Figure 15 Fig 15 l 20 11 16 25 526mm 635mm E 27 3 16 30 5 16 690mm 770mm F 23 3 16 23 3 8 589mm 594mm PLACING THE DISHWASHER 10 1 Straighten and position the hot water supply line and the electrical supply cable as shown in Figure 16 so that they will align with their channels under the dishwasher base 2 Position the dishwasher close enough to the enclosure so that you can run the dishwasher drain hose to the under sink drain connection Make certain that the hot water supply line and the electrical supply cable are in their channels under the dishwasher base as shown in Figure 17 letter A 3 Place the dishwasher directly in front of the enclosure 4 Perform a level check as shown in Figure 17 Adjust the rear leveler by turning the center screw at the front of the dishwasher as shown in Figure 18 letter B Turning the screw clockwise raises the rear of the dishwasher Adjust the front levelers by turning them with a screwdriver as shown in Figure 18 letter C Turning the levelers to the right raises the dishwasher If additional height is needed shims may be added under the leveler feet 5 Push the dishwasher into the enclosure SECURING THE DISHWASHER Drive the mounting screws through the holes in the mounting brackets as shown in Figure 19 letter A for Top Mount or as shown in Fi
15. nclosed on the top and both sides by standard residential kitchen cabinetry Select a location as close to the sink as possible for easy access to water supply and drain lines For proper dishwasher operation and appearance ensure that the enclosure is square and has the dimensions shown in Figure 2 If the dishwasher is to be installed in a corner make sure that there is adequate clearance to open the door as shown in Figure 3 letter A AX WARNING ELECTRICAL SHOCK FIRE HAZARD Do not allow the electrical and water supply lines to touch Separate channels are provided under the dishwasher see page 10 If the enclosure requires openings for the electrical supply cable hot water supply line and dishwasher drain hose place them within the dimensions shown by the shaded area of Figure 4 to avoid interference with the dishwasher frame or other components Make the openings for the electrical supply cable and hot water supply line 1 25 4mm diameter Make the opening for the dishwasher drain hose 1 1 4 32mm diameter If the openings are made through wood sand them smooth If the openings are made through metal make them large enough to accommodate grommets or other protective sheaths with inside diameters of 1 25 4mm for the electrical supply cable and the hot water supply line and 1 1 4 82mm for the dish washer drain hose ELECTRICAL PREPARATION Figure 5 ar B 4 75mm 100mm 3 8
16. r hose and 90 elbow fitting NOTE Regardless of where the hot water supply line enters the enclosure following the guidelines on page 8 position the line 14 855mm from the enclosure s left side as shown in Figure 7 letter A NOTE Decide whether braided hose or copper tubing will be used for the hot water supply plumbing and purchase the correct type of hot water supply shut off valve 90 elbow and necessary fittings for the hot water supply plumb ing Continued on next page PLUMBING PREPARATION continued Figure 8 Figure 9 Figure 10 Figure 11 Drain Plumbing Dishwasher Connection Piece If the dishwasher is to drain either directly into the household drain plumbing or through an air gap install a dishwasher connection piece under the sink as shown in Figure 8 letter A Installing an Air Gap If local ordinances require an air gap as shown in Figure 9 letter B install it according to the manufacturer s instructions Disposer If a disposer is to be installed as shown in Figure 10 letter C install it according to the manufacturer s instructions Whether the disposer is newly installed or existing remove the disposer s dishwasher drain connection plug DISHWASHER PREPARATION Dishwasher preparation involves four tasks e Installing the Mounting Brackets e Removing the Toe Panel e Installing the 90 elbow fitting e Junction Bo
17. rough the strain relief as shown in Figure 25 Leave 3 4 inches of insulated wire extending through the strain relief plate 3 Tighten the strain relief screws 4 Slide the strain relief plate into the junction box and secure it to the junction box with the supplied screw Continued on next page 13 14 ELECTRICAL CONNECTION continued Ad WARNING FIRE HAZARD loose or improper electrical connections can cause Figure 26 Figure 27 Figure 28 fire Make certain that all electrical connections are properly made e Do not pre twist the wires before connecting them with wire nuts e Extend the dishwasher s stranded wires 1 8 8mm beyond the power supply cable s solid wires aS shown in Figure 26 5 Using the supplied wire nuts connect the electri cal supply wires to the dishwasher s wires black to black white to white and green or bare to green or bare Make certain that the insulated wires show no bare wire from the bottoms of the wire nuts Gently tug the wires to make certain they are securely connected 6 Press the wires into the junction box Make certain that the wire nuts do not loosen 7 Place the cover on the junction box and secure it to the junction box with the supplied screw DOOR TENSION ADJUSTMENT only on DWHD94BF After the dishwasher is installed open and close the door several times to make sure that it does so with ease If the door closes too quickly or
18. x Preparation Installing the Mounting Brackets CAUTION Before installing the supplied mounting brackets letter E in the Materials Supplied section of this manual decide which method of securing the dishwasher into its enclosure will be used Once the mounting brackets are installed on the dishwasher removing them is difficult and will damage the mounting brackets and the dishwasher The dishwasher can be secured into its enclosure in two ways 1 Top Mount is used for countertops made of wood or other materials that can easily drilled Orient the mounting brackets as shown in Figure 11 letter A and position the two small tabs on the mounting brackets over the two slots on the dishwasher s front corners Push the mounting brackets down firmly to insert the tabs into the slots 2 Side Mount is used for countertops made of marble granite or other very hard materials that cannot be easily drilled Bend the mounting brackets along the small holes and in the same direction as the two small tabs Orient the mounting brackets as shown in Figure 11 letter B and position the two small tabs on the mounting brackets over the two slots on the dishwasher s front corners Push the mounting brackets down firmly to insert the tabs into the slots DISHWASHER PREPARATION continued Figure 14 Removing the Toe Panel DWHD94BF Regular Toe Panel The toe panel is loosely attached with tape Remove the tape and pull the toe panel aw
Download Pdf Manuals
Related Search