The First Years I440 Car Seat User Manual
Contents
1. This carrier must always be used with the base 2 Leveling base Place seat in base and check level indicator to see if base is level LEVEL is indicated by the ball being completely in the green area Pull out on the yellow release knob and slide the angle foot to raise the base or to lower the base angle The base is NOT level and seat back is NOT at 45 degree unless the ball is in the green NOTE If needed a towel or pool noodle can be used for extra elevation and angle adjustment 16 Section 7 Installation and Use 7 2 Auto Belt Base Installation with Lap Belt 1 After Ball is in the green area on Level indicator open Lock Off and thread auto safety belt through the labeled Belt Here auto safety belt path Press down on base with knee tighten auto belt and insert buckle tongue into buckle Close and secure Lock Off to eliminate slippage Pull on auto safety belt to ensure the auto buckle is secure CHECK level indicator to ensure the ball is in the green area Pull out on the yellow release knob and slide the angle foot to raise the base or to lower the base angle 4 CHECK base at safety belt path for movement Base should not move more than 1 inch in any direction 5 f base moves repeat steps until all safety steps are met Ud Section 7 Installation and Use 7 2 1 Auto Belt Base Installation with Lap and Shoulder Belt 1 After Ball is i2. repeat steps until all safety steps are met Section 7 Installation and Use CRS Locking Clip Installation 7 4 1 A Free Sliding Latch Plate will require the use of a locking clip if the Lock Off feature is not used The First Years requires the use of the Lock Off at all times 2 A locking clip may be purchased by calling Learning Curve 1 888 899 2229 3 Follow the base installation on pages 15 to 19 This carrier must always be used with the base 4 Thread the locking clip on the belt as close to the latch plate as possible It must be within 1 inch 20 Section 7 Installation and Use HEU Carrier onto the Base 1 Ensure base is installed correctly as described in the Base Installation section before installing the Infant seat This carrier must always be used with the base 2 Lower Infant seat on to the base 3 NOTE You should hear a positive click when the Infant Seat is installed correctly Pull up on the Infant Seat handle to ensure the Infant Seat is attached to the base see figure 1 4 CHECK level indicator to ensure the ball is in the green area Turn yellow adjust height knob clockwise to raise the base or counter clockwise to lower base CHECK base for movement at the belt path Base should not move more than 1 inch in any direction 5 If the base does not pass both checks repeat installation steps until the base installation passes both checks 6 NEVER att
3. Infant Seat labels can result in injury or death to a child from striking the vehicle s interior during a sudden stop or crash Even if the Infant Seat seems easy to use on your own it is important to read these instructions and the vehicle owner s manual for details you might miss The instructions in this manual and in your vehicle owner s manual must be followed carefully If there is a conflict between the two the vehicle owner s manual must be followed Failure to use the automobile seat belt or LATCH or to adjust it properly can result in your child striking the vehicle s interior during a sudden stop or crash Serious injury or death can occur DO NOT allow others baby sitters friends T etc to use this Infant Seat unless they read and understand the instructions and labels and can demonstrate proper use to your satisfaction Use only car seat accessories manufactured by Compass Accessories can affect your child s safety in a sudden stop or crash DO NOT modify or attach any toys padding or other items to this Infant Seat Untested modifications or padding could result in injury in a crash Secure this Infant Seat with the vehicle seat belt or LATCH bars at all times even when there is no child in it An unsecured child restraint can injure others if a crash occurs Direct sunlight can make Infant Seat surfaces hot enough to burn your child Use caution and check the vehicle and Infant Seat on h
4. Statement Use Of Via 1440 Infant Seat Child Restraint In Conjunction With Side Airbags To determine the types of side impact air bag s your vehicle may have for individual seating positions please refer to your owner s manual The First Years Via 1440 Infant Seat child restraint may be used in any rear seating position equipped only with side impact airbags that are roof mounted with curtain type deployment For all other vehicles with other types of side impact airbags please refer to your specfic vehicles owner s manual for appropriate use of child restraints or call the automobile manufacturer for more information 3 Vehicle Seats DO NOT use this Infant Seat with the following vehicle seats NO Seats Which Seats Which Rear Seats Of Face Sides Of Face Rear Small Extended Vehicle Of Vehicle Cab Pickup Trucks 4 Latch Bar Location Consult your automobiles owner s manual or manufacturer for location and availability of LATCH anchor points LATCH Bar Locations 5 Vehicle Seat Belt Systems Use only the vehicle s lap and shoulder belt lap belt or LATCH system when restraining this Infant Seat Design and operation of vehicle seat belt systems vary from vehicle to vehicle and from seating location to seating in the same vehicle Not all vehicle seat belts betls can be used with a child restraint Refer to the information in this section information on the various types of vehicle se
5. 1 888 327 4236 TTY 1 800 424 9153 or go to http NHTSA 36 Removing Seat Pad Gently unsnap metal snaps after following the directions on page 32 Cleaning Seat Pad Head Bolster and Cano Hand wash in cool water and mild soap Air dry Cleaning Shell Wipe with mild solution of soap and water Avoid wetting labels Rinse with clean water Never use household detergents or solvents Reattach Seat Pad Follow directions on page 33 to reattach pad Section 11 Replacement Parts We know pads get worn or damaged Some companies charge outrageous prices when their parts wear out At The First Years we will sell you replacement parts at or near our cost plus what it costs us to handle and ship them They are still expensive but we promise they are fair prices Of course replacement instructions are always free Please call for current prices on other items 37 Blank Page Keep this instruction manual for future use Store in pocket on bottom of the Infant Seat afirst years Learning Curve Brands Attn Consumer Services 2021 9th St SE Dyersville 52040 or call 1 888 899 2229 or log onto www learningcurve com O 2008 Learning Curve Brands 4000000609 02 08
6. ECK 1 866 732 8243 EVERYONE rides buckled up or the vehicle DOES NOT GO Make NO EXCEPTIONS for adults or children If someone unbuckles the vehicle STOPS Being firm and consistent will result in fewer discipline problems as children grow older An unrestrained person can be thrown into and injure other passengers NEVER try to tend to a crying child s needs while driving Never take a child out of a child restraint for comforting while the vehicle is moving Put heavy or sharp items in the trunk Loose items can be deadly in a crash If you need to use a blanket in cold weather put the child in the restraint and cover both with the blanket 34 j Did you read and understand these instructions and labels on the Infant Seat Y Is the child the proper weight and height for the Infant Seat HI Is the child secured in the back seat NI Did you pull the harness adjustor tight H You should not be able to pinch the harness if the harness is properly fastened Is the shoulder strap at or below the child s shoulders Did you hear the positive click telling you that the infant seat is locked in the base Is the base used and located in the rear automobile seat N Is the base located in the center seat a window seat with no airbag or a window seat with a roof mounted curtain type deploying airbag deploys down the window Is the base buckled in the automobile with either the LATCH sys
7. INSTRUCTION MANUAL afirst years This Infant Seat is for use by children who meet BOTH of the requirements below Weight is 4 to 22 pounds 1 8 to 10 kg Height is 30 inches or less 76 cm Failure to use this Infant Seat properly increases the risk of serious injury or death in a sudden stop or crash Do not install or use this Infant Seat until you have read and understand the instructions in this manual Section 1 Introduction Dear Parents Thank you for purchasing The First Years Via 1440 We hope that it will make your baby s travel safer easier and more pleasant We believe the Via 440 is the easiest Infant Seat to use We do more testing than most companies to make it as safe as possible And we use the latest methods to assure the highest quality The First Years monitors the molding of every key plastic part Our MoldTrac technology allows us to watch every part as itis molded In addition we place a number on each seat so key parts can be traced You will find this number on the bottom of your seat and on the top of your base We have tried very hard to keep our instructions simple and understandable We apologize for beginning our instructions with so many warnings but they are very important for you to properly restrain your child Read and understand all of the ao and warnings The safety of your child depends on it If you have any questions or need assistance please contact the
8. R O SUFRIR Read your vehicle s LESIONES GRAVES El asiento trasero es el lugar m s seguro para los ni os de 12 a os o menores owners manual to see to turn off your airbag if you have no back seat or a child must ride in the front seats For side airbags see page 10 e DO NOT use this Infant Seat in rear seat of a compact pickup truck Severe head injury or death can occur ALWAYS use the base with the carrier in this child restraint NEVER attempt to install the Infant Seat without the base The Infant seat has not been designed to be used with out a base 1 National Highway Traffic Safety Administration NHTSA alerts vehicle owners that according to accident statistics children under age 13 are safer when properly restrained in the rear seating positions rather than in front seating positions 2 Refer to vehicle owner s manual for car seat installation instructions for your specific vehicle Use of Infant Seat in a vehicle rear seat location Never put Infant Seat in a front seat location unless permitted by vehicle owner s manual For vehicles with air bags refer to vehicle owner s manual for child restraint installation information If a vehicle front seat location with an air bag must be used follow the vehicle manufacturer s instructions for manufacturer s instruction to disable air bags that could cause serious injury to child and move seat back as far as possible The First Years Policy
9. and Use Harness System C Harness Adjuster 5 To loosen harness system The Harness Adjuster is located at the Lower end of the Infant Seat between the child s feet Press the yellow center button and pull the harness system outward from the seat back over the baby s shoulder 6 To Tighten Harness System Lock Chest Clip and 5 Point Buckle Pull Harness webbing out until harness is snug over the child s shoulder Note A snug strap should not allow any slack It lies ina relatively straight line without sagging It does not press on the child s flesh or push the child s body into an unnatural position Prevent injury Always have child restrained with harness system when child is in this Infant Seat Section 7 Installation and Use Harness System D Shoulder Height Adjustment 7 To Raise or Lower Harness Loosen harness system Pull out the yellow adjustment knob located on the seat back and slide the adjustment to either the upper or lower slot depending upon the height of the child Note After adjustment for shoulder height move yellow knob up and down to ensure the yellow knob has engaged Note The harness should be at m e or below the shoulder of the child Note You should not be able to pinch excess webbing if the harness properly fastened Note A snug strap should not allow any slack It lies in a relatively straight line without sagging It does no
10. at belt systems LAP SHOULDER BELTS Combination lap shoulder belt with locking latch plate This type of belt system has a latch plate that will not allow the lap portion of the belt to loosen once it is buckled The belt is tightend by pulling hard on the shoulder portion of the vehiclebelt while pushing down on the restraint Combination lap shoulder belt with sliding latch plate This type of belt system has a latch plate that allows the belt to slide through even when it is buckled Many vehicles with this type of seat belt system can be locked by pulling all the seat belt webbing out Refer to your vehicle owner s manual for details on switching the retractor from ELR mode to ALR mode The belt is tightend by pulling hard on the shoulder portion of the vehicle belt while pushing down on the restraint 12 LAP BELTS Manually adjusted lap belt This type of lap belt is tightened by 17 pulling on the excess belt once it is 2 buckled Lap belt with automatic locking retractor ALR This belt system s retractor locks automatically and does not allow the lap belt to lengthen once it is buckled cH Tighten by feeding the autobelt back into the retractor while pushing down on the infant restraint Unsafe Vehicle Seat Belt Systems DO NOT use this Infant seat with the following vehicle seat belts Passive Restraints Passive Restraints Motorized Lap Or Shoulder Shoulder Belt Belt Mo
11. e only in a rear facing position when using this restraint in a vehicle Use only with children who weigh between 4 and 22 pounds 1 8 and 10 kg or less and whose height is 30 inches 76 cm or less Snugly adjust the belts Harness provided with this child restraint around your child Secure this child restraint with the vehicle s child restraint Anchorage system LATCH if available or with a vehicle belt Follow all instructions on this child restraint and in the written Instructions located on the bottom of the seat Do not use without instructions Call 1 888 899 2229 to obtain instructions Register your child restraint with Learning Curve DO NOT place this rear facing child seat in a front seat that has an airbag NEVER leave child unattended under any circumstance SUFFOCATION HAZARD Infant Carrier can roll over on soft surfaces and suffocate child Never place carrier on beds sofas or other soft surfaces STRANGULATION HAZARD Child can strangle in loose restraint straps Always use harness NEVER leave child in carrier when straps are loose or undone FALL HAZARD Child s movements can slide carrier NEVER place carrier near edges of counter tops tables or other elevated surfaces Be sure handle locks into a Position before lifting carrier Section 7 Installation and Use Base Installation 7 1 1 Level Vehicle Check to make sure vehicle is on a level surface
12. emoval 7 14 1 Unfasten outer snaps remove canopy head bolster and cold weather boot if included 2 Loosen harness and place the harness out of the way as indicated in the picture 3 Locate the Easy Off pad flaps and separate 4 Pull harness through the slots in the Easy Off Pad 5 Remove pad and launder per the instructions on page 36 Prevent injury Do not use this Infant Carrier without the pad Section 7 Installation and Use Pad Installation 7 15 1 Lower dry pad on shell allowing the attachment flaps to remain open 2 Pull harness through open flaps Place harness in the harness location slots Place harness to the side 3 Close flaps and secure with the hook and loop fastener 4 Fasten outer snaps replace Canopy Head Bolster Prevent injury Do not use this Infant Carrier without the pad For assistance with installation or use contact one of the following sources Learning Curve at Phone 1 888 899 2229 Email cs learningcurve com Acertified Child Passenger Safety CPS Technician in your area To locate a CPS Technician in your area log onto www nhtsa dot gov and select Child Passenger Safety and then select Technician Contact Locator Or attend a car seat check up event For car seat check up event location and timing Log onto www nhtsa dot gov and select Child Seat Inspections Log onto www seatcheck org Call 1 866 SEAT CH
13. empt to install the infant seat with the auto belt The Infant 24 Seat can only be used with a base Section 7 Installation and Use CRS Installation Pictograms 7 6 pou 1 Base installed with Lap belt This carrier must always be used with the base 2 Base installed with Lap and Shoulder belt This carrier must always be used with the base 3 Base installed with LATCH connectors and LATCH Bars This carrier must always be used with the base This carrier must always be used with the base 22 Section 7 Installation and Use CRS Installation Pictograms 7 6 1 Infant Seat and Base installed with Lap belt This carrier must always be used with the base 2 Infant Seat and Base installed with lap and shoulder belt This carrier must always be used with the base 3 Infant Seat and base installed with LATCH connectors to LATCH bars This carrier must always be used with the base This carrier must always be used with the base 02 Section 7 Installation and Use Handle 7 7 1 Positioning of Handle Press red button on both sides of the handle to move handle Only use position A to carry the Infant Seat 2 Check That Handle is Locked Before the Infant seat is lifted for any reason check to make sure handle is locked into position by pushing forward and pulling back on the handle 3 Handle position in auto Never have handle in position A when infant
14. n the green area on Level indicator open Lock Off and thread auto safety belt through the labeled Belt Here auto safety belt path Press down on base with knee tighten auto belt and insert buckle tongue into buckle Close and secure Lock Off to eliminate slippage Pull on auto safety belt to ensure the auto buckle is secure CHECK level indicator to ensure the ball is in the green area Pull out on the yellow release knob and slide the angle foot to raise the base or to lower the base angle 4 CHECK base at safety belt path for movement Base should not move more than 1 inch in any direction 5 f base moves repeat steps until all safety steps are met Section 7 Installation and Use CRS Connector LATCH Anchor Points 7 3 1 N Consult your automobile s owners manual or manufacturer for location and availability of LATCH lower anchor points Remove BOTH LATCH Lower Anchor connectorc from the LATCH Lower Anchor storage compartment Attach the right and left LATCH Lower Anchor to the anchor points Press down on the base with your knee and pull up on the webbing loop until the webbing is taut CHECK level indicator to ensure the ball is in the green area Pull out on the yellow release knob and slide the anglefoot to raise the base or to lower the base angle CHECK base for movement at the belt path Base should not move more than 1 inch in any direction If base moves
15. ot sunny days NEVER leave child unattended under any circumstance DO NOT use this Infant Seat if it has been in a crash There may be hidden damage and it must be replaced Your insurance company may provide some assistance replacing this infant seat DO NOT use this Infant Seat if it is damaged in any way or has missing parts STOP USING THIS INFANT SEAT AND THROW IT AWAY after the date on the back of the seat THROW IT AWAY in a dark trash bag Do Not sell to a thrift or consignment shops or at flea markets NEVER place the Infant Seat in a shopping cart 0000007004 ER AS NEVER place the infant seat on your hip Carry the Infant Seat at your side at all times Section 4 Use Recommendations The First Years advises parents that children should use a child restraint with a built in harness system until they exceed the weight or height limits specified by the manufacturer 1440 Infant Seat Use Requirements This child restraint is designed for use by children whose Weight is between 4 and 22 Ibs 1 8 and 10 kg and Height 30 inches or less 76 cm Child MUST meet both of these requirements to use this Infant Seat DO NOT use this Infant Seat when top of child s head is closer than 1 inch fron the top edge of seat back Severe head or neck injuries can result without proper head support Section 5 Infant Seat Parts Aluminum Full Rotation Handle 75 Head Bolste
16. r 5 Point Harness Harness Adjuster Base Height Adjust The Infant Seat must be used with a base Base Release Harness Knob Height Eos Handl Kno ba andle y Release Serial Buttons Number Harness Plate Retention Instruction Hooks Storage Section 5 Infant Seat Parts Base Height Adjust Auto Belt Lock Off 2 ar Anchors Steel Retention Angle Indicator Hooks God The Infant Seat must be used with a base Section 6 Selecting A Vehicle Seating Location Use only in a rear facing position when using this restraint in a vehicle DO NOT use this infant seat in a forward facing position Only use this Infant Seat with the vehicle s seat belts or LATCH System DO NOT use this Infant Seat with vehicle seat belts mounted to the vehicle door or door frame DO NOT use this Infant Seat if it cannot be properly installed Some child restraints will not fit some vehicle seating positions NEVER use this 4 DO NOT place rear facing child seat Infant Seat in any S on front seat with air bag DEATH OR 4 SERIOUS INJURY A vehicle seating 3 SS i AON The back seat is the safest place for position equipped A children 12 and under H H NO col l asiento infantil autom vil orientado haci with an active air bag atr s en lasent delantero del veh culo que tenga una bolsa neum tica de seguridad El ni o podr a MORI
17. seat is installed in the automobile Position B C D or E are acceptable use positions in the automobile Prevent injury Never have handle in position A when the Infant Seat is installed in the automobile Section 7 Installation and Use 1440 Removal from base 7 8 1 Grip red handle and gently pull up 2 Pull straight up on the 1440 by the handle and the front or back edge Prevent injury Always have child restrained with harness system when child is in this Infant Seat Section 7 Installation and Use Harness System 7 9 A Chest Clip 1 To Unlock Squeeze center locking tabs Pull Chest clip apart 2 To Lock Align locking tabs and press Chest Clip together until tabs snap into place Note Try to pull Chest Clip apart to ensure the clip is locked Prevent injury Always have child restrained with harness system when child is in this Infant Seat DR Section 7 Installation and Use Harness System B 5 Point Buckle 3 To UnLock Press red center button until the 5 Point Buckle releases Pull Buckle Tongue from Buckle 4 5 Point Buckle To Lock Align Buckle Tongues and insert both Buckle Tongues into Buckle until Buckle Tongues lock in place Note Try to remove Buckle Tongues from Buckle to ensure the Buckle is locked Prevent injury Always have child restrained with harness system when child is in this Infant Seat Section 7 Installation
18. t press on the child s flesh or push the child s body into an unnatural position Prevent injury Always have child restrained with harness system when child is in this Infant Seat Section 7 Installation and Use Canopy 7 10 1 Installation To install Canopy Insert Canopy post until the canopy clicks into place Note The pivoting canopy rod must be at the back of the seat 1 2 Rotation The canopy has a full rotation Push or pull to raise or lower into desired location Cold Weather Boot Cover 7 11 1 Installation Not included with all models Slide boot cover over the front on the Infant seat Secure boot cover by fastening snaps to canopy post snaps A Prevent injury Always have child restrained with harness system when child is in this Infant Seat Section 7 Installation and Use Head Bolster 7 12 1 Positioning Removal The Head Bolster is held in place with hook and loop fasteners The top inside of the Head Bolster should be as close to the top of the child s head as possible Babies with Low Birth Weight 7 13 Rolled towels can be added for side support for smaller infant E ARE Add a rolled wash cloth for added support between the crotch belt and the infant Prevent injury Always have child restrained with harness system when child is in this Infant Seat section installation and Use fon Installation and Use Pad R
19. tem or auto safety belt system Is the angle indicator in the Green area Is the handle rotated to one of the back positions Did you check for hot surfaces in sunny weather Current date is not after Do Not use After date on bottom of Infant Seat Has the airbag been deactivated a vehicle with a front only seat Section 9 Additional Information Certification This child restraint system conforms to all applicable Federal Motor Vehicle Safety Standards for use in motor vehicles This Infant Seat is certified for use in motor vehicles Aircraft Use This Restraint is Certified for Aircraft Use Vehicle Seat Protection Protect vehicle seat Use a thin car seat mat thin towel or thin blanket under the Infant Seat Instruction Manual Storage Store instruction manual in pocket on the bottom of the Infant Seat Infant_Seat Useful Life DO NOT use this Infant Seat after date on back of seat Parts may be missing damaged or the Infant Seat may have been in a crash Registration Information Child restraints could be recalled for safety reasons You must register this restraint to be reached in a recall Send your name address and the restraint s model number to Learning Curve Brands Attn Consumer Services 2021 9th St SE Dyersville 52040 or call 1 888 899 2229 or log onto www learningcurve com For recall information call the U S Government s Vehicle Safety Hotline at
20. the First Years Staff at 1 888 899 2229 this instruction manual for future use tore in pocket on the back of Infant Seat No car seat can guarantee protection from injury in every situation but proper use helps reduce the risk of serious injury or death Section 2 Table Of Contents Section 1 Introduction Section 2 Table Of 2 Section 4 Use Recommendati Section 5 Infant Seat parts Section 6 Selecting A Vehicle Seating Location 10 Section 2 Table Of Contents AIR BAG WARNING NEVER use this Infant Seat in any vehicle seating position equipped with an active air bag Read your vehicle s owners manual to see to turn off your airbag if you have no back seat oa child EN on front seat with air bag DEATH OR must ride in the front Y tt EY DO NOT place rear facing child seat seats For side airbags see page 10 The back seat is the safest place for children 12 and under NO coloque el asiento infantil para el autom vil orientado hacia atr s en el asiento delantero del veh culo que tenga una bolsa neum tica de seguridad El ni o podr a MORIR O SUFRIR LESIONES GRAVES El asiento trasero es el lugar m s seguro 3 para los ni os de 12 a os o menores Section 3 Warnings A WARNING A DEATH or SERIOUS INJURY can occur Failure to follow these instructions and
21. unted On Front Door Lap Belt with Emergency Locking Retractor ELR Do Not Use This lap belt stays loose when when buckled and can move until locks in sudden stop or crash 13 Unsafe Vehicle Seat Belt Systems cont Lap and Shoulder Belt with Dual Retractors Do Not Use Each autobelt Strap has a retractor at each end and is attached to the latch plate at one end 6 Vehicle Seat Belt Retractors Consult your vehicle s owners manual for types of retractors that are in your automobile and the function of the retractors Acceptable Autobelt Retractor Type ALR Automatic Locking Retractor Allows belt to be pulled in one motion until fastened then operates as a ratchet winding in slack preventing further extension until completely rewound In most belts you will hear a faint clicking sound that indicates the belt is locked and ratcheting in Switchable When Adjusted to the ELR mode Manually adjustable from ELR mode to ALR mode For most pull belt webbing all the way out of the retractor to activate theALR mode A slight click may be heard but the belt will ratchet in to retractor once switched into ALR mode In some models the retractors switch from ELR to ALR by pushing a button Unacceptable Autobelt Retractor Type ELR Emergency Locking Retractor Allows the belt to befreely extended or rewound It locks only when the vehicle slows changes direction or stops suddenly 14 Us
Download Pdf Manuals
Related Search