Texas Instruments TI-83 Calculator User Manual
Contents
1. Thermador Corporation 1998 Litho U S A 11 00 Thermador VENTILATORS IMPORTANT SAFETY INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK OR INJURY TO PERSONS OBSERVE THE FOLLOWING A Use this unit only in the manner intended by the manufacturer If you have any questions contact the manufacturer B Before servicing or cleaning unit switch power off at service panel and lock service disconnecting means to prevent power from being switched on accidentally When the service disconnecting means cannot be locked securely fasten a prominent warning device such as a tag to the service panel CAUTION For General Ventilating Use Only Do Not Use To Exhaust Hazardous or Explosive Materials and Vapors WARNING TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE a Never leave surface units unattended at high settings Boil overs cause smoking and greasy spillovers that may ignite Heat oils slowly on low or medium settings b Always turn hood ON when cooking at high heat or when cooking flaming foods c Clean ventilating fans frequently Grease should not be al lowed to accumulate on fan or filter d Use proper pan size Always use cookware appropriate for the size of the surface element WARNING TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF ARANGE TOP GREASE FIRE OBSERVE THE FOLLOWING A SMOTHER FLAMES with a close fitting lid cookie sheet or other metal tray then turn off the2. CLEANING CONTINUED FROM PREVIOUS PAGE H64 65 Remove two 2 shipping screws from base of each lamp shade Lamp shade will now snap out for easy cleaning Install two 2 75 Watt maximum flood lamps For best results use reflector flood not supplied with hood into lamp shade sockets ON H65 ONLY Install two 2 250 Watt maximum infrared heat lamps using type R 40 not supplied with hood into angled sockets only CAUTION Do not use scouring powders or abrasive cleaners on the hood as these may permanently mar the finish Do not use oven cleaners to clean the stainless steel hood even if recommended by the manufac turer of the cleaner Refer to installation instructions and consult your countertop supplier prior to making counter opening Consult with a heating and ventilating engineer for your specific ventilation requirements For the most detailed information refer to installation instructions accompany ing product or write Thermador indicating the model number Thermador reserves the right to change specifications or design without notice Some models are certified for use in Canada Thermador is not responsible for products which are transported from the United States for use in Canada Check with your local Canadian distributor or dealer Thermador 5551 McFadden Avenue Huntington Beach CA 92649 Thermador 5551 McFadden Avenue Huntington Beach CA 92649 800 735 4328 ECO 71566 19 08 9631
3. gas burner or the electric element BE CAREFUL TO PREVENT BURNS If the flames do not go out immediately EVACUATE AND CALL THE FIRE DEPARTMENT CONTINUED ON NEXT PAGE CONTINUED FROM PREVIOUS PAGE B NEVER PICK UP A FLAMING PAN You may be burned C DO NOT USE WATER including wet dishcloths or towels a violent steam explosion will result D Use an extinguisher ONLY if I You know you have a Class ABC extinguisher and you already know how to operate it 2 The fire is small and contained in the area where it started 3 The fire department is being called 4 You can fight the fire with your back to an exit READ AND SAVE THESE INSTRUCTIONS OPERATING INSTRUCTIONS Hoods This Thermador ventilating hood is operated by a solid state motor speed control which allows infinite control of motor speeds for selection of air exhaust and sound level The ventilator should be turned on 5 minutes before cooking in order to draw the currents of air upward through the hood That way when heat smoke moisture grease and cooking odors arise they will be carried upward and forced outside thereby minimizing their drift into other rooms Drafts across the cooking surface from an open window door etc may cause the escape of heat moisture grease and cooking odors from the hood Such drafts should be prevented whenever possible The best job of ventilation in the kitchen is done when the only air currents are those create
4. appearance and protect the finish from surface damage Filter Cleaning Pull open the housing door and remove the filters Filters may be washed in hot sudsy water or sprayed with a household kitchen cleaner such as Fantastik then rinsed with hot water or washed in the dishwasher Replace after they are dry CONTINUED ON NEXT PAGE
5. d by the ventilator itself CLEANING INSTRUCTIONS For maximum efficiency clean filter and hood regularly Do not allow grease to accumulate on the hood or the ventilator surface To Clean the Filter Remove the filter by applying slight thumb pressure on the sides of the clips and pulling the filter out by the top of the filter frame Filter may be washed in the dishwasher or washed in warm soapy water drain and dry before installing 2 To Clean Motor and Blade Unit First remove filter and DISCONNECT PLUG Loosen nut and remove BLOWER ASSEMBLY REMOVAL blower using Remove Remove BI handle see figure aoe i sing below Wipe entire Handle a unit clean with a damp cloth Do not use a dripping wet cloth as water may enter the motor and cause damage Do not remove blower wheels UNPLUG 3 To Reinstall Unit reverse the procedure in steps and 2 4 To Clean Hood Surface Use only mild soap or detergent for cleaning all hood surfaces Dry surfaces with a cloth for maximum luster Enamel Surface Use only mild soap or detergent for cleaning all hood surfaces Dry surface with clean cloth for maximum luster Stainless Steel Surface The stainless steel used in the manufac ture of these hoods is resistant to most stains and surface rust when cleaned and protected with a stainless steel cleaner polish Apply this type of product regularly according to manufacturer s directions to maintain
Download Pdf Manuals
Related Search