Sunbeam SR6200 Waffle Iron User Manual
Contents
1. Using your iron 1 Insert the plug into a 230 240 volt power outlet and turn the power on The power ON light positioned on top of the handle will illuminate to indicate that the iron is switched on and heating 2 Turn the temperature dial to the desired setting by aligning the setting on the dial with the temperature indicator The thermostat light will illuminate to indicate that the iron is heating to the selected temperature When the thermostat light goes out the iron has reached the selected temperature and is ready to use NOTE When the temperature dial is changed from a high setting to a lower temperature setting during ironing the thermostat light will go out immediately This indicates that the iron is cooling to the selected temperature To ensure that the iron has reached the selected temperature and is not too hot wait until the thermostat light comes on again and then goes out before ironing Steam ironing Follow steps 1 and 2 above NOTE When steam ironing ensure that the temperature dial is set to any temperature within the steam band and that the tank is at least 1 4 full of water 3 Turn the steam dial to the desired Steam setting Steam Dial Temperature Dial m cotton Wwe For best results select the steam setting that corresponds to the selected temperature as indicated on the temperature dial Using your Sunbeam Verve Iron continued Dry ironing Follow steps2. damp cotton cloth while hot Caution Do not use scouring pads abrasives or harsh cleaners to clean your Resilium Teflon Platinum Pro or Stainless steel soleplate as these will scratch and damage the surface Ironing Tips and Tricks Tip 27 Iron shirts like a pro Start with the collar working from the outer edges into the middle Iron the shoulder next followed by the cuffs and sleeves Place the collar at the narrow end of the board so that one front panel of the shirt is extended flat Iron the front panel from shoulder to shirt tail Rotate to iron the back of the shirt Rotate and complete the remaining front panel Tip 34 Tips for T shirts Straighten seams on t shirts before hanging out to dry To avoid damage to printed graphics and logos turn the t shirt inside out and iron the reverse side of the print Never iron areas of your t shirt where perspiration marks are visible as the heat of the iron will permanently fix the stain Tip 54 Hung out to dry When washing is complete remove shirts from the machine immediately shake them out and hang them on coat hangers to air dry this will keep wrinkles to a minimum Tip 18 Selecting the right temperature If you are unsure of the correct setting for a particular garment test a small area such as a seam or inside hem before ironing a visible area Start with a low temperature and slowly increase the heat to find the best setting Tip 33 D
3. on the cord Turn the power off and remove the plug when the appliance is not in use and before cleaning Do not use your appliance with an extension cord unless this cord has been checked and tested by a qualified technician or service person Always use your appliance from a power outlet of the voltage A C only marked on the appliance This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance The temperature of accessible surfaces may be high when the appliance is operating Never leave an appliance unattended while in use Do not use an appliance for any purpose other than its intended use Do not place an appliance on or near a hot gas flame electric element or on a heated oven Do not place on top of any other appliance Do not let the power cord of an appliance hang over the edge of a table or bench top or touch any hot surface Do not operate any electrical appliance with a damaged cord or after the appliance has been damaged in any manner If damage is suspected return the appliance to the nearest Sunbeam Appointed Service Centre for examination repair or adjustment For addi
4. 1 and 2 above 3 Select DRY on the steam dial This will cut off the steam flow if there is water in the tank Using the shot of steam The shot of steam can be used when dry or steam ironing when the temperature dial is set to any temperature within the steam band or above the two dot ee setting 1 Ensure the tank is at least full of water 2 Select the desired temperature and wait until the thermostat light goes out 3 Press the shot of steam button several times with the iron on the soleplate to prime the pump Note If the tank has run dry it may be necessary to re prime the pump after filling the iron with water Using the spray mist The spray mist can be used whether dry or steam ironing to pre dampen hard to iron fabrics 1 Ensure the tank is at least full of water 2 Press the spray button during ironing to release a fine mist from the spray nozzle The safety auto off feature Models SR6550 SR6650 SR6850 amp SR6855B The safety auto off mechanism automatically turns the iron off if you forget The iron will automatically shut off if left on the heel rest vertical for 15 minutes or in the ironing position horizontal for 30 seconds without being moved See figure 2 The thermostat and power lights on the handle will flash and a warning beep will sound to let you know that you have left the iron unattended Power to the iron s heating element will be cut Once the iron is moved
5. L glablial aS ans i i doalan dioe Yao sea itage ftd adi ddufifilenaa Yukarda belirtilen g venlik nlemlerinin anla ld ndan emin olunuz Xin ki m ch c rang nh ng bi n ph p l m an to n k tr n du gc hi u r Sunbeam s Safety Precautions SAFETY PRECAUTIONS FOR YOUR IRON Do not leave a hot iron within reach of children If they come into contact with a hot iron it could lead to serious burns ron only on an ironing board An iron takes approximately 30 minutes to cool down Allow the iron to cool completely before storing Do not wind the cord around the soleplate while the iron is still hot Do not leave the iron unattended while it is plugged into the power outlet Always unplug the iron from the power outlet before filling or emptying the water tank The iron must be used and rested on a stable surface The iron is not to be used if it has been dropped if there are visible signs of damage or if it is leaking Sunbeam is very safety conscious when designing and manufacturing consumer products but it is essential that the product user also exercise care when using an electrical appliance Listed below are precautions which are essential for the safe use of an electrical appliance Read carefully and save all the instructions provided with an appliance Always turn the power off at the power outlet before you insert or remove a plug Remove by grasping the plug do not pull
6. Verve Irons Instruction Booklet This book covers the use and care of the following Verve9 Irons SR6855B Verve 685 Resilium Shot amp Spray Iron with Safety Auto Off SR6850 Verve 68 SR6650 Verve 66 SR6550 Verve 65 SR6250 Verve 62 Resilium9 Shot amp Spray Iron with Safety Auto Off Stainless Shot amp Spray Iron with Safety Auto Off Platinum Shot amp Spray Iron with Safety Auto Off Platinum Shot amp Spray Iron Please read these instructions carefully and retain for future reference Contents Sunbeam s Safety Precautions Features of your Verve Iron Using your Verve Iron The Safety Auto Off Feature Care and Cleaning of your Verve Iron lroning Tips amp Tricks Ironing Chart oo OND BW Important instructions retain for future use adhe Eyii aUl Lb ial agis Ge Sls aa PSA TEAR LIRATE Assurez vous que les pr cautions ci dessus relatives la s curit sont bien comprises Versichern Sie sich dass die obenstehenden SicherheitsmaBnahmen verstanden werden BeBaldvete rt ot rrapari vo npoqguA Egi aopasiag yivovtat karavort o Pastikan bahwa tindakan tindakan keselamatan seperti di atas dimengerti anda Accertatevi che le suddette norme di sicurezza siano comprese a dovere LROREPREK lt BRAID TENE SAO Yeepete ce peka norope criomeHaTuTe Mepka H npernaa3nuBocr ce no6po pas6paHn Asegurese de que las precauciones de seguridad precedentes sean bien comprendidas xig do Laia Y
7. id to apply pressure steam and hold Tip 42 Table settings to impress To avoid unwanted creases always iron your table cloth after taking it out of the cupboard A dinner party is a special occasion so treat the table cloth as you would your own outfit For best results lay towels across your table and iron the table cloth over the towels This will save you time and ensure a beautifully presented table setting Ironing Chart Fabric Temp setting Ironing lroning recommendation MINIMUM Min to s Dry iron on reverse side of fabric Acrylic MINIMUM Dry iron on reverse side of fabric Min to while still damp MINIMUM Min to SYNTHETIC Acetate Nylon Iron on reverse side of fabric Polyester Iron on reverse side of fabric SYNTHETIC Rayon Iron on reverse side of fabric SYNTHETIC Mainly dry iron Steam can be used under Viscose ME manufacturer s instructions lron on reverse side of fabric Use an ironing cloth to prevent shine marks and use regular shots of steam SILK Silk Check label and follow manufacturer s instructions Use setting for the fibre requiring the lowest setting WOOL Steam iron on reverse side of fabric Wool e or use an ironing cloth Brush gently to raise the fibres WOOL Steam iron on reverse side of fabric Wool Blends Pus or use an ironing cloth Brush gently to raise the fibres COTTON Steam iron on reverse side of fabric Corduroy HUNE or use an i
8. ive is removed by rubbing the soleplate with a cloth dampened with methylated spirits Fill the water tank and empty the water This will rinse out any foreign particles remaining in the water tank from the manufacturing process NOTE When turned on for the first time your new iron may give off vapours for up to 10 minutes This is due to the initial heating of the materials used It is safe not detrimental to the performance of the iron and will not reoccur Filling the iron with water Before filling the iron with water ensure the power is turned off and the plug is removed from the power outlet The iron can be filled with water while it is hot Place the iron on its heel and open the water inlet cover Slowly pour water into the water inlet until the maximum water level is reached Do not exceed the maximum water level indicator Push the water inlet cover firmly to close NOTE The special soleplate design allows you o use tap water with your Verve iron without affecting the steam performance However in very hard water areas Sunbeam recommends he use of distilled water or water which has been demineralised For best performance we recommend the use of Sunbeam Water Demineraliser available rom selected retailers This will produce up to 30 litres of demineralised water Do not fill the iron with fabric conditioner starches or any other solution as these will damage the steam mechanism Do not use contaminated water
9. matically switches itself off if left in the ironing position horizontal for 30 seconds or in the heel rest position vertical for 15 minutes For more information on the safety auto off feature see page 7 Power light IIluminates to indicate that the iron is connected to the power outlet and the power is turned on Thermostat light IIluminates to indicate that the iron is heating and goes out when it has reached the temperature selected on the temperature dial The thermostat light cycles on and off during ironing as the iron maintains the selected temperature Stable heel rest Extra large heel rest keeps the iron stable on the ironing board Cord wrap The built in cord wrap facility allows you to wind the cord around the heel for neat and tidy storage of the cord when the iron is not in use Concentric steam and temperature dials The steam and temperature dials are positioned together for easy adjustment Variable steam dial Allows you to select the desired steam output for each garment Alternatively select the DRY setting to iron without steam Temperature dial Allows you to select the desired temperature for each garment The adjustable temperature dial also indicates the amount of steam recommended for use on each temperature setting o 6 Using your Sunbeam Verve Iron Before first use Remove any adhesive stickers plastic covers or cardboard sleeves from the soleplate Ensure that all adhes
10. n to you by this guarantee are in addition to your other rights and remedies under any laws which relate to the appliance Our goods come with guarantees that cannot be excluded under the Australian Consumer Law and under the New Zealand Consumer Guarantees Act In Australia you are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure Should your appliance require repair or service after the guarantee period contact your nearest Sunbeam service centre For a complete list of Sunbeam s authorised service centres visit our website or call Australia www sunbeam com au 1300 881 861 Units 5 amp 6 13 Lord Street Botany NSW 2019 Australia New Zealand www sunbeam co nz 0800 786 232 26 Vestey Drive Mt Wellington Auckland New Zealand Need help with your appliance Contact our customer service team or visit our website for information and tips on getting the most from your appliance In Australia Visit www sunbeam com au Or call 1300 881 861 In New Zealand Visit www sunbeam co nz Or call 0800 786 232 is a registered trademark Verve and Resilium are registered trademarks of Sunbeam Corporation Teflon is a registered trademark of DuPont Made in Chi
11. na Due to minor changes in design or otherwise he product may differ from the one shown in this leaflet Copyright Sunbeam Corporation Limited 2013 ABN 45 000 006 771 Units 5 amp 6 13 Lord Street Botany NSW 2019 Australia Unit 3 Building D 26 Vestey Drive Mt Wellington Auckland ew Zealand Sunbeam Corporation is a division of GUD Holdings Ltd 6 13
12. on t be afraid to iron silk Don t be afraid to iron silk Although delicate in appearance silk is the strongest and most resilient of all natural fibres To achieve the best results set to a low cotton setting and use regular shots of steam Always use a pressing cloth to avoid shine marks Tip 13 Ironing the seam Always press seams in the same direction they were made When a garment is produced the fibres will naturally settle in the direction they were initially pressed so it s best not to iron against the grain Tip 26 Sort types of fabric Sort articles to be ironed according to the type of fabric This will reduce the need to adjust the temperature constantly Start with articles requiring lower temperatures and work your way through to items requiring higher settings Tip 4 2 Summer frocks and frills Steam is the key when ironing delicate summer fabrics such as muslin cotton and linen Don t press down with the iron simply hover above the garment and steam it using a vertical shot of steam Ruffling netting tulle or intricate hand detailing is also best ironed using this method Tip 5 Pressing your winter woollies Steam is crucial when pressing your winter woollies Woollen garments can be hung and steamed using the vertical shot of steam feature After steaming brush the garment with your hand to plump up woollen fibres If ironing the garment flat it is best to use a pressing cloth Don t be afra
13. roning cloth Brush gently to raise the fibres Cotton COTTON Steam iron while still damp or use spray eee to dampen Use medium to high steam Iron on reverse side of fabric or use an ironing cloth to prevent shine marks especially with dark colours Iron while still damp or use spray to dampen Use medium to high steam MAXIMUM Iron while still damp or use spray Denim e e to Max to dampen Use maximum steam WOOL Cotton Blends LINEN e e e to Max Sunbean 2 Year Replacement Guarantee In the unlikely event that this appliance develops any malfunction within 2 years of purchase 3 months commercial use due to faulty materials or manufacture we will replace it for you free of charge Should you experience any difficulties with your appliance please phone our customer service line for advice on 1300 881 861 in Australia or 0800 786 232 in New Zealand Alternatively you can send a written claim to Sunbeam at the address listed below On receipt of your claim Sunbeam will seek to resolve your difficulties or if the appliance is defective advise you on how to obtain a replacement or refund Your Sunbeam 2 Year Replacement Guarantee naturally does not cover misuse or negligent handling and normal wear and tear Similarly your 2 Year Replacement Guarantee does not cover freight or any other costs incurred in making a claim Please retain your receipt as proof of purchase The benefits give
14. t having to refill the tank regularly Drip stop steam system The drip stop steam system automatically stops water flowing to the steam chamber should the temperature fall too low to generate steam This prevents dripping even at low temperatures Full length button groove For ironing around buttons 2400 watts for fast heat up Provides faster initial heat up and rapid heat recovery during ironing The 2400W element helps to maintain your selected temperature and provides superior shot of steam output Teflon Platinum Pro non stick soleplate SR6250 amp SR6550 Teflon Platinum Pro is DuPont s premium non stick Resilium non scratch soleplate coating It glides easily across all types of fabric and SR6850 amp SR6855B prevents sticking This hard wearing surface consists of a Resilium is a durable scratch resistant surface that provides a superior glide and prevents rucking Exclusive to Sunbeam this premium soleplate features 172 steam holes to maximise steam distribution unique three coat system for superior durability and scratch resistance It simply wipes clean for fuss free maintenance Steam Dial Temperature Dial pe Stainless steel soleplate SR6650 Sleek and smooth stainless steel is an excellent heat conductor and is extremely durable and hard wearing It features a quality polished finish that is easy to clean and care for Safety auto off The iron auto
15. the power will reconnect Allow the iron to heat until the thermostat light goes out and continue ironing as normal 15 minutes 30 seconds Figure 2 Care and Cleaning After each use 1 Turn the power off and remove the plug from the power outlet 2 Allow the iron to cool before winding the cord around the built in cord wrap Storage Always store the iron on its heel rest Do not store the iron with the soleplate facing down or in the carton Cleaning To clean the exterior of your iron wipe over with a damp soft cloth and wipe dry Caution Do not use harsh abrasives chemical cleaners or solvents to clean the exterior of your iron as these will damage the surface Cleaning the steam holes To remove build up from the steam holes which may affect steam performance use a cotton wool tip moistened in methylated spirits Cleaning the Resilium soleplate SR6850 amp SR6855B Wipe with a soft damp cloth and wipe dry Cleaning the Stainless Steel soleplate SR6650 Using a stainless steel or metal cleaner rub gently with a damp cloth and wipe dry Cleaning the Teflon Platinum Pro non stick soleplate SR6250 SR6550 The non stick coating reduces sticking of fabrics and starches to the soleplate Do not iron over sharp objects such as buttons studs and zippers as these may scratch the surface Wipe the soleplate with a damp soft cloth after each use If polyester has burnt to the soleplate iron a
16. tional protection Sunbeam recommend the use of a residual current device RCD with a tripping current not exceeding 30mA in the electrical circuit supplying power to your appliances Do not immerse the appliance in water or any other liquid unless recommended Appliances are not intended to be operated by means of an external timer or separate remote control system This appliance is intended to be used in household and similar applications such as staff kitchen areas in shops offices and other working environments farm houses by clients in hotels motels and other residential type environments bed and breakfast type environments If you have any concerns regarding the performance and use of your appliance please visit www sunbeam com au or contact the Sunbeam Consumer Service Line Ensure the above safety precautions are understood Features of your Sunbeam Verve Iron Powerful shot of steam Pressing the shot of steam button instantly produces a powerful shot of steam to remove stubborn wrinkles Vertical shot of steam Pressing the shot of steam button with the iron in an upright position produces a vertical shot of steam which is ideal for steaming curtains and suits and removing creases from delicate fabrics Fine spray mist Pressing the spray button provides a fine mist spray to dampen hard to iron fabrics Easy fill water inlet Holds 300ml of water for continual high steam performance withou
Download Pdf Manuals
Related Search