Home

Speco Technologies DVR-16TN Camcorder User Manual

image

Contents

1. lt gt Backspace Delete Cancel OK e Use Direction keys to select a character e Press ENTER to add the selected character to the Host Name entry field e When done move the cursor to lt OK gt and press ENTER to save the settings and exit DVR 4TN 8TN 16TN 16TS 16TT Series 73 SPECO TECHNOLOGIES 01 06 5 1 7 Ste 5 1 7 2 74 User s Manual NOTE No any two DVR 4TN DVR 8TN DVR 16TN series units should be set the same Host Name DDNS Port This item allows the user to setup the port for DDNS Press UP DOWN Direction keys to change the port Submit Update When done move the cursor to this item and press ENTER to submit the settings NOTE If there are two DVR 4TN DVR 8TN DVR 16TN series units set with the same domain name the later setting will not be submit successfully RS485 Setup This menu allows the user to setup the parameters of the units RS 485 communications port From the Main menu select lt RS485 Setup gt and press ENTER The following menu is displayed RS485 Setup 1 Unit ID 224 2 Baud Rate 9600 3 Bits 8 4 Stop 1 5 Parity None Unit ID This item is used to change the RS 485 ID address of the unit The ID is with the range of lt 1 gt to lt 255 gt The default is lt 224 gt Baud Rate The Baud rate options for association with the protocol are lt 2400 gt lt 4800 gt lt 9600 gt lt 19200 gt lt 38400 gt and lt 57600 gt
2. To create the connection and close this wizard click Finish lt Back Finish Cancel DVR 4TN 8TN 16TN 16TS 16TT Series 115 SPECO TECHNOLOGIES 01 06 User s Manual e Now the dial in connection is established ie Network Connections BEX Fie Edit View Favorites Took Advanced Hep Q Back B search C Folders D i s E Network Connections b E Go Broadband d HiNet By oe Dial up OT ICF Connection Al Yahoo Connection aes A Incoming rde Incoming Connections LAN or High Speed Internet ST Local Area Connection 3 ST 1394 Connection 7 wr Local Area Connection 4 Details Cab 2 CS e Network Connections System Folder Establishing Dial out Connection The Dial out function enables the user to establish dial up modem communication to and from the DVR 4TN 8TN 16TN 16TS 16TT series unit for remote notification use Follow the instructions that follow to set up your DVR and PC DVR Configuration e Connect a USB modem to the USB port and connect a working phone line to the modem e Press MENU and input the Administrator password to access the OSD Main menu Select lt Network Setup gt and then lt Dial out Setup gt to set up the Dial out settings e Select the lt Email Address gt in the Network Setup menu to edit an e mail address for alarm notification e Select lt Event Setup gt in the Main menu and set the Email Notice function to lt ON gt enabled e Exit the OSD
3. DVR 4TN 8TN 16TN 16TS 16TT Series 13 SPECO TECHNOLOGIES 01 06 2 4 User s Manual Connecting Short term Device If you plan to install any short term external devices such as USB CD RW USB Hard Disk Drive etc to the DVR 4TN 8TN 16TN 16TS 16TT series and want to use them as part of the unit system Make sure those devices are connected only after the DVR 4TN 8TN 16TN 16TS 16TT is powered up The DVR 4TN 8TN 16TN 16TS 16TT series unit can only recognize the external devices after the power up process is completed Rear Panel Connections There are several connectors on the rear panel of the DVR 4TN 8TN 16TN 16TS 16TT series units available for installations The following figure shows the connectors by name and a detailed description of each connector follows There is one difference between the rear panel of different models DVR 4TN 8TN 16TN has an IEEE 1394 connector and DVR 16TS TT has a 1000M LAN Port instead shown as below figures Rear Panel of DVR 4TN 8TN 16TN Main Monitor Main Monitor Call Monitor VGA BNC BNC Video In Video Looping maam e OF es Dommen T d b i H L H Main Monitor RS 232 Alarm UO and IEEE1394 Audio In Out USB2 0 LAN Power Switch Power Supply S Video RS 485 x2 x2 x2 DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual Rear panel of DVR 16TS 16 TT Main Monitor Main Monitor Call Monitor VGA BNC BNC Video In Video Looping Main Monit
4. New Connection Wizard 7 Select the check box next to each device you wantto use for incoming connections Connection devices RE Conexant D480 MDC V 92 Modem Devices for Incoming Connections You can choose the devices your computer uses to accept incoming connections lt Back l Next gt Cancel In Incoming VPN Connection menu choose lt Do Not allow virtual private connections gt and click on lt Next gt r New Connection Wizard Incoming Virtual Private Network VPN Connection Another computer can connectto yours through a VPN connection Virtual private connections to your computer through the Internet are possible only if your computer has a known name or IP address on the Internet lf you allow VPN connections the system will modify the Windows Firewall settings to allow your computer to send and Ee VPN packets Do you wantto allow virtual private connections to this computer Allow virtual private connections Do not allow virtual private connections lt Back Next gt Cancel DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual s In User Permission menu select the users that will be using this connection If needed add a new user with the same user password that is set up in the Dial out Setup menu in local DVR When done click lt Next gt to continue New Connection Wizard J
5. User Permissions You can specify the users who can connect to this computer Select the check box next to each user who should be allowed a connection to this computer Note that other factors such as a disabled user account may affect a user s ability to connect Users allowed to connect CIE _vmware_user__ _vmware_user_ IE 1234 1234 wf R I admin admin1234 io Ke Andy Wu D Ke ASPNET ASP NET Machine Account a D I Guest ei ls i Lal Add Remove lt Back Next gt Cancel r New Connection Wizard s computers Select the check box next to each type of networking software that should be enabled for incoming connections Networking software MF Internet Protocol TCP IP N wm Li File and Printer Sharing for Microsoft Networks WI KR Li VMware Bridge Protocol EN Description Transmission Control Protocol Internet Protocol The default wide area network protocol that provides communication across diverse interconnected networks lt Back Next gt Cancel Networking Software Networking software allows this computer to accept connections from other kinds of DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 In Networking Software menu select lt TCP IP gt and click on lt Properties gt 119 120 User s Manual e In TCP IP address assignment if the PC has DHCP server then choose lt Assign
6. X Image Quality Ave File Size Y Per Channel PPS 6 levels 136 DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 Diagram Sample Half D1 NTSC 720x240 60PPS PAL 720x288 50PPS 30PPS N 25PPS P 15PPS N 12 5PPS P 11 25PPS N 9 375PPS P 7 5PPS N 6 25PPS P 3 75PPS N 3 125PPS P 1PPS N 1PPS P DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual X Image Quality Ave File Size Y Per Channel PPS 6 levels 137 User s Manual Diagram Sample CIF NTSC 360x240 120PPS PAL 360x288 100PPS 30PPS N 25PPS P 15PPS N 12 5PPS P 11 25PPS N 9 375PPS P 7 5PPS N 6 25PPS P 3 75PPS N 3 125PPS P 1PPS N 1PPS P X Image Quality Ave File Size Y Per Channel PPS 6 levels 138 DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06
7. Refer to Section 4 1 1 Viewing Modes for more detailed information PLAY STOP Press this key to switch between live image and playback video NOTE Video taken within the latest 5 10 minutes cannot be played back because the video is still saved in the buffer FREEZE e Press FREEZE while viewing live image the live video will be frozen but the date time information shown on the monitor will continue updating Press FREEZE again to return to live mode e Press FREEZE while playing recorded video the playback video will be paused Press LEFT RIGHT to move the recorded video reverse forward by a single step Press FREEZE again to continue playing video SEQ Sequence Press to start automatic sequencing of the video coming in from the installed cameras SEARCH In both Playback and Live mode the user can press SEARCH to call up the Search menu for searching and playing back recorded video by date and time or events MENU Press this key to call up the OSD setup menu ZOOM ENTER e In OSD menu or selection interface press this key to make the selection or save settings e In live full screen view mode press to view a 2x zoom image press key again to return DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual CHANNEL e When in both Live and Playback modes press the CHANNEL key to view the corresponding video in full screen The number of the CHANNEL keys corresponds to the number of
8. The user can export a video clip with or without a digital signature Set the item to lt YES gt to export with the signature file or lt NO gt to export without the signature file Each recorded video with a digital signature will be exported automatically into four files including gpg avi sig and readme txt The gpg file name is the same as the last eight MAC Media Access Control address digits of the unit Make sure that you have an external storage device such as a USB Hard Drive or USB ThumbDrive available and connected to the appropriate port for export For more information about verifying a digital signature see Appendix E Verifying Digital Signature Erase Disc This function is used to remove information found on a CD RW or DVD RW disk prior to exporting new information to the drive Select lt YES gt and press ENTER to start deleting data Quick Video Export through Front Panel The unit provides you a quick way to export video files to the built in CD RW or an external device such as a USB thumb Drive and save the video to drv file If you want to export video to an external device make sure the external storage unit has been connected to the DVR unit and the port has been set appropriately for video export NOTE Once an external device has been connected to the DVR unit the device has priority over the built in CD RW which means that the desired video will be exported to the external devic
9. User s Manual From the Main menu select lt Video Export gt and press ENTER The menu is displayed below Video Export 1 Select Device 2 Select Ch CH1 CH2 CH3 CH4 3 From 2005 03 19 AM 07 50 05 4 To 2005 03 28 PM 03 09 18 5 Select Events 6 Data Type Normal 7 Digital Signature NO 9 Erase Disc NO 10 Begin Export NO Select the External Device The available external devices for exporting video will be listed by name and free size in Select Device menu The Select Device menu displays as follows Select Device Device Name Available Sel XXX XXX X X XX 256 MB NO XX XXX XX XXXX 1 5 GB NO The DVR 4TN 8TN 16TN 16TS 16TT series only supports EXT3 file system If you connect an external HDD to the unit make sure the format of the HDD is EXT3 If not please format this HDD to EXT3 first lt Device Name gt This item shows the name of the available device lt Available gt This item shows the free space of the available device lt Select gt Set the item to lt YES gt to start the export or lt NO gt to cancel DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 4 4 1 2 User s Manual Select Video for Exporting After selecting video clips set the item lt Begin Export gt to lt YES gt and press ENTER to start exporting Following are the menu items for selecting video Select Channel Select the channel that the administrator wants to export Move the cursor
10. lt gt Backspace Delete Cancel OK e Use Direction keys to move the cursor to the desired character e Press ENTER to add the selected character to the username entry field e When done move the cursor to lt OK gt and press ENTER to save the settings and exit SMTP Port This item is used to change the SMTP port to another port if necessary SMTP is usually assigned to operate over Internet port 25 To change the SMTP port move the cursor to lt SMTP Port gt in SMTP Setup menu and press ENTER Use UP DOWN keys to change the values in the selected field DVR 4TN 8TN 16TN 16TS 16TT Series 71 SPECO TECHNOLOGIES 01 06 5 1 6 8 72 User s Manual SMTP Account This item allows user to setup the SMTP username Follow these steps to setup the login password e Select lt SMTP Account gt from SMTP Setup menu and press ENTER A virtual keyboard displays e Use Direction keys to move the cursor for selecting character e Press ENTER to add the selected character to the SMTP Account entry field e When done move the cursor to lt OK gt and press ENTER to save the settings and exit SMTP Password This item allows the user to setup the SMTP password Follow these steps to setup the password e Select lt SMTP password gt from SMTP Setup menu and press ENTER A virtual keyboard displays e Use Direction keys to move the cursor for selecting a character e Press ENTER to add the selected character
11. 720x288 25PPS in PAL Per Camera Config Cameral Select CH1 Day Night Weekend Normal PPS 7 5 7 5 7 5 Normal Qlty Mid Mid Mid Event Max PPS 30 30 30 Event Qlty Best Best Best Event Act Both Both Both Camera Select This item is used to select a desired channel for setting the associated parameters Move the cursor to lt Camera Select gt and press ENTER then select a channel using UP DOWN keys Press ENTER again to confirm the setting Normal PPS Normal PPS Picture per Second is used to set the recording rate for normal status Please note that the total normal pps for all channels is limited under the maximum PPS for each Record mode To increase one channel s pps you may have to reduce others first Event pps is not restricted to this rule since a smart event scheduler will handle the total pps automatically Normal Qlity This item is used to set the picture size for normal status recording The available options are listed as follow lt Low gt lt Fair gt lt Mid gt lt High gt and lt Best gt DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual 5 4 4 4 Event Max PPS Event Max PPS is used to set the event recording rate for Event status Normally the Event PPS is set to be equal to or greater than Normal PPS the setting depends on your application If the Event PPS is set to lt 0 gt the DVR 4TN 8TN 16TN 16TS 16TT series unit stops recording event v
12. Daylight Saving Time Daylight Saving Time This item is for those people who live in certain regions to observe Daylight Saving Time Select lt ON gt to enable or lt OFF gt to disable the function If the function is disabled the DST Start End time and DST Bias will be grayed out and cannot be accessed NOTE If this function is enabled the date time information will be shown on the screen with a DST icon when playing back recorded video or searching video in the event list S indicates summer time and W indicates wintertime DST Start End This is used to program the daylight saving duration Use Direction keys to move the cursor to the next or previous field use UP DOWN to change the settings in the selected field DST Bias This allows the user to set the amount of time to move forward from the standard time for daylight saving time The available options are lt 30 gt lt 60 gt lt 90 gt and lt 120 gt minutes DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual 3 6 Record Schedule Quality Setting The Record Setup menu allows the user to set recording quality recording schedules and other recording parameters This menu will not be able to access if you enter the OSD Setup Menu with User s password In the Main menu move the cursor to lt Record Setup gt and press ENTER the following menu is displayed Record Setup 1 Record Mode 720x240 60PPS 2 Sche
13. See your network system administrator or IT personnel for appropriate values for these setting IP This item is used to configure the IP Internet Protocol address of the unit The IP address is the identifier for your computer or device on a TCP IP LAN or WAN Please note that to set a static IP address DHCP must be set to lt OFF gt Netmask A netmask is a 32 bit mask used to divide an IP address into subnets and specify the networks available hosts Its value is defined by your network administrator It takes the form as for example 255 255 255 255 This item allows the user to enter the value of the Netmask for the unit Please note that to configure the item DHCP must be set to lt OFF gt Gateway A Gateway is a node on a network that serves as an entrance to another network Users are allowed to specify the IP address of the gateway or router associated with this unit To configure this item DHCP must be set to lt OFF gt DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual DNS DNS is the abbreviation for Domain Name System which is an Internet service that translates domain names into IP addresses because domain names are easier to remember This item allows the user to specify the IP address of the Domain Name System associated with the unit To configure this item DHCP must be set to lt OFF gt If the network server is unavailable when using DHCP the
14. Windows XP Service Pack 2 Windows NT 5 1 build number 2600 Step 6 Click lt Step1 gt sheet and then choose lt lnstall to System Root gt and lt Start drive on boot gt options When done click lt Install Drive gt button After the assignments are made click lt Save Assignments gt button Step 7 Click lt Step1 gt sheet and then choose lt Install to System Root gt and lt Start drive on boot gt options When done click lt Install Drive gt button Click lt Step3 gt sheet Then click lt Start Drive gt button 132 DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual Step 8 Click lt Step1 gt sheet and then choose lt Install to System Root gt and lt Start drive on boot gt options When done click lt Install Drive gt button After last step is done reboot the PC for the changes to take effect The HDD will be added into your PC s database after rebooting Start Playing the drv file After the HDD being added into your PC s database you can now use the SpecoPlayer to play the drv file in your HDD Please referring to the steps below Step 1 You can find the SpecoPlayer in the CD that ship with the package start it and push the PLAY button on the upside of the frame Step 2 Click the Open Device button as below picture then choose the HDD Drive that you just assigned 5 DYR Player Version 1 0 0 48 Selection Figure 1 Select the Drive
15. lt Daytime Record gt and press ENTER This item is for you to select whether you want the DVR to record during daytime If yes using UP DOWN to select lt Yes gt as option or select lt No gt for not recording during daytime e Repeat the same procedures through the 3rd and 4th items respectively Note that lt Weekend Record gt will be not accessible if you select lt NO gt for the item lt Weekend Schedule gt in lt Schedule Setup gt e The Quality will be automatically accounted for according to upper items you have set and shown on the screen This item is for read only Five options including lt Best gt lt High gt lt Mid gt lt Fair gt and lt Low gt can be viewed in this item We strongly recommend to keep the quality higher than Middle AN NOTE The current number of connected cameras will affect the recording quality which wil be automatically calculated through the lt ezRecord Setup gt Therefore once you disconnect cameras or connect more cameras to the unit you should reset the lt ezRecord Setup gt Data Lifetime Data Lifetime indicates the time that a recording is saved and remains in the HDD between the creation and deletion of a record Only those video files recorded during Data Lifetime will be displayed on the screen and can be played back those video files recorded outside the duration time will be hidden Press ENTER to select this item in Record Setup menu and then use UP
16. menu Select lt Shutdown gt in Main Menu and press ENTER to enter the Shutdown menu which displays as follows Shutdown 1 Power Off Execute 2 Reboot Execute lt Power Off gt Select this item to shut down the unit Do not disconnect the power during shut down until the message You can safely turn off DVR now displays lt Reboot gt Select this item to reboot the unit The color bar and system checking information are displayed on the monitor until the unit is completely restarted DVR 4TN 8TN 16TN 16TS 16TT Series 23 SPECO TECHNOLOGIES 01 06 3 4 24 User s Manual Entering OSD Setup Menu The OSD Main menu contains a list of items that are used to configure the DVR 4TN DVR 8TN DVR 16TN series To enter the Main menu correct Administrator or User password is required Three sets passwords are offered for different Administrators and Users if there is more than one To enter OSD Main menu press MENU and then enter either Administrator or User password The Password Verification screen will then display as follows Password Verification Press Channel Keys To Enter Password 4 8 Digits Press lt Key To Delete NOTE If entering wrong password for 3 times the system will be locked out and you will not be able to enter OSD menu within 2 minutes The default passwords are shown in the following table The same passwords are used for entering the remote viewing software SpecoRemote Ad
17. 16TT Series SPECO TECHNOLOGIES 01 06 125 User s Manual DVR 16TN 16TS 16TT Alarm I O Definition i Definition i Definition 1 RS485 D 12 N A 23 Alarm in 7 2 RS485 D 13 N A 24 Alarm ln 8 3 Ground 14 N A 25 Alarm ln 9 4 Normal Close 1 15 Ground 26 Alarm In 10 5 Common Node 1 16 Ground 27 Alarm in 11 6 Normal Open 1 17 Alarm in 1 28 Alarm In 12 7 Ground 18 Alarm In 2 29 Alarm In 13 8 Normal Close 2 19 Alarm In 3 30 Alarm In 14 9 Common Node 2 20 Alarm In 4 31 Alarm In 15 10 Normal Open 2 21 Alarm in 5 32 Alarm In 16 11 Ground 22 Alarm In 6 33 l 126 DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual Appendix G Hard Disk Installation The following steps describe how to install HDD s to your DVR 4TN 8TN 16TN 16TS 16TT unit Step 1 Disconnect power from the unit Remove the 8 screws that hold the top cover in place 3 on each side 2 in the rear Remove the top cover by sliding it to the rear Figure 2 Internal construction of DVR 4TN 8TN 16TN 16TS 16TT Figure 3 Remove screws from the bracket DVR 4TN 8TN 16TN 16TS 16TT Series 127 SPECO TECHNOLOGIES 01 06 User s Manual Step 2 Assemble the HDD to the bracket Figure 5 Attach the HDD to the bracket Figure 6 After assembly 128 DVR 4TN
18. 2x2 2x2 i3 Ta S 14 5 6 11 12 13 2x2 3x3 3x3 4x4 4 1 2 Digital Zoom Users are able to view a 2x full screen in live mode To view the 2x full screen follow these steps e Press the CHANNEL key to view the corresponding camera in full screen e Press ZOOM to enter a 2x full screen zoom mode of the selected camera e f you need to view a specific area of the 2x zoomed screen use Direction keys to pan tilt the zoomed area around the original image e Either press ZOOM again or ESC to leave the zoom mode 4 1 3 Viewing Live Cameras Users are allowed to view live cameras in several view modes including full screen 2x2 3x3 and 4x4 General operation under live mode is described as follows To Freeze Live Image Press FREEZE while viewing a live image the image then pauses but the date time information does not and the system clock continues running Press FREEZE to pause the live image press FREEZE again to resume the live camera view DVR 4TN 8TN 16TN 16TS 16TT Series 31 SPECO TECHNOLOGIES 01 06 4 1 4 32 User s Manual Viewing Recorded Video To view recorded video the user can press the PLAY STOP key directly When the PLAY STOP key is pressed the unit starts to continue playing back the recorded video from the suspended point of record If the PLAY STOP key is being used for the first time the unit will playback from the very beginning of the record Alternatively a user can select records from the Search menu
19. 4 7 TET 100 599 Data lh 6 seisein ence tee en tee er tee Wer tee eer tee er mee terre re 100 99 6 EE TE 101 59 Erase NN 101 399 BEJNEK oiean aa AA 101 5 10 EE 101 Appendix A Technical Specifications egusesbreruseEs esurebeeEueEEkEuCNEEERdEEEEENESKEKEEEAEKEEEEEEeeER 103 Appendix B Record Configuration sisiciiiisinisnniniinnnnninnindinnannnninnininiannnes 105 Appendix C Record Duraton eegretpueuetreERSEERREEKENEKENRREEREEEEKKELSNEKEREEEENEKELEAEEEKENEEENRN 109 Appendix D Dial up Connections via Modem eeeeceeeeeeeeeeeeeeeeeeeeeeeeeseeeeeeeeees 112 Establishing Dial in CONNEC E 112 Establishing Dial out Connection sese sese eee eee eee eee eee 116 Appendix E Verifying Digital Signature 0 cccccssssesseeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeseeeenees 122 Appendix F Alarm UO Pin Definition wesissiiensiiusiinsvdscicenianesidnsadsdiardicunidnnicsaeandianedsedaduniann 125 Appendix G Hard Disk 1nstallation sessvesvsresssrszesvrasvssssgesogrsvvsssvsszsgesvssessssscsrresvsssesesve 127 Appendix H HDD PC Player Tool Introduction eeeceeeeeeeeeeeeeeeeeeeeeeeeeseeeseeeenees 131 WSs OM EXTAFS On Eeer 131 Start Playing the drv HIS esse eee 133 Appendie i IR e 135 Appendix J ezRecord Diagram Sample ccccccccssssseeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeenees 136 DVR 4TN 8TN 16TN 16TS 16TT Series 9 SPECO TECHNOLOGIES 01 06 User s Manual Overview The DVR 4TN 8TN 16TN 16
20. Connection Wizard Phone Number to Dial Whatis your ISP s phone number Type the phone number below Phone number j You might need to include a 1 or the area code or both If you are not sure you need the extra numbers dial the phone number on your telephone If you hear a modem sound the number dialed is correct 114 DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual e Enter the Username and Password that is set up in the Dial in Setup menu r 7 New Connection Wizard Internet Account Information You will need an account name and password to sign in to your Internet account Type an ISP account name and password then write down this information and store itin a safe place lf you have forgotten an existing account name or password contact your ISP User name Password Confirm password Use this account name and password when anyone connects to the Internet from this computer Make this the default Internet connection lt Back Next gt Cancel e Click lt Finish gt to complete the dial in connection r x New Connection Wizard Wizard You have successfully completed the steps needed to create the following connection a Completing the New Connection DVR Dial In Share with all users of this computer The connection will be saved in the Network Connections folder
21. Control Software SpecoRemote Access Control 2 Level Password DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 103 User s Manual Monitoring Playback Recording System Setup Dome Remote Operation Camera Control RS232C D sub 9 pin female RS485 Terminal Block Dome Control Protocol DynaColor Pelco P Pelco D AD422 104 DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual Appendix B Record Configuration 1 The following three tables are offered for users who useDVR 4TN 8TN 16TN unit Sdlvielte ode D ode 0x480Q 30PP HD 0 6 a PP Preset Item Normal PPS Normal Size Event PPS Event Size Event Active Ach NTSC 7 5 PAL 6 25 Sch NTSC 3 75 PAL 3 12 Best 1 8ch NTSC 30 Quality NTSC 2 75 PAL 25 PAL 2 12 16ch 9 16ch 30 KB 30 KB NTSC 1 PAL 1 NTSC 7 5 PAL 6 25 NTSC 3 75 PAL 3 12 1 8ch NTSC 30 NTSC 2 75 PAL 25 PAL 2 12 16ch 9 16ch 18 KB 30 KB NTSC 1 PAL 1 NTSC 7 5 PAL 6 25 Sch NTSC 3 75 PAL 3 12 Extended 1 8ch NTSC 30 Record NTSC 2 75 PAL 25 PAL 2 12 16ch 9 16ch 6 KB 30 KB NTSC 1 PAL 1 0 NTSC NTSC 30 0 PAL PAL 25 128Kbps NTSC 1 NTSC 1 DSE PAL 1 ete PAL 1 iD SE NTSC 4 NTSC 4 GALA 2 KB GALA 2 KB Both 512Kbps NTSC 4 NTSC 4 DSL PAL 4 ane PAL 4 Ge Se User selected User selected User selected User selected User selected 28 KB 28 KB Both Alarm Motion 4ch 16 KB 28 KB 8ch Bo
22. DOWN keys to set the data lifetime The value ranges from lt 1 gt to lt 365 gt days or select lt 0 gt to disable the function NOTE If you want to play back the video which is outside the data duration of lifetime please extend the duration till the recording data time of the video is included DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 5 4 7 5 4 8 5 4 9 User s Manual Pre Alarm Recording This item is used to set the duration time of pre alarm recording video The pre alarm recording function aims to give the user the opportunity to view a more complete event video The user can see the video recorded after the alarm is triggered and the video recorded ahead the alarm When an event is triggered while normal recording is in effect the unit will start copying the pre alarm and the post alarm video to the event video The pre alarm duration can be set from 0 30 seconds The default setting is 15 seconds The quality of the pre alarm video is the same as the quality setting for normal record video and the quality of the post alarm video is the same as the quality setting for event record video Circular Recording The user can choose to record video in circular mode or in linear mode If you choose to record in circular mode then the unit begins to overwrite the oldest recorded video and stores new video over the HDD spaces If you choose to record in linear mode instead the unit stops recording w
23. Main menu and press ENTER The following menu is displayed Monitor Setup 1 Show Camera Title YES 2 Monitor Brightness 0 3 Monitor Contrast 0 4 Monitor Chrominance 0 5 Screen Center Adjust 6 Show Color Bar Execute 7 VGA Resolution 800x600 The following sections describe the items found in the Monitor Setup menu Show Camera Title This item allows the user to choose whether to display the camera title on the screen or not The default is lt YES gt which displays the camera titles with the video Monitor Brightness This function allows the user to adjust the brightness of the image displayed on the monitor Move the cursor to the item then press ENTER and use UP DOWN keys to adjust the numeric value The range of brightness values is lt 32 gt to lt 31 gt The default setting is lt 0 gt Monitor Contrast This item is used to adjust the color contrast of image The range of contrast values is lt 32 gt to lt 31 gt the default setting is lt 0 gt Monitor Chrominance Move the cursor over this item and press ENTER for adjusting the chrominance of the image displayed on the monitor Use UP DOWN keys to adjust the numeric value The range of chrominance values is lt 32 gt to lt 31 gt the default setting is lt 0 gt DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual 5 2 5 Screen Center Adjust This item is used to adjust the screen center of t
24. PAL 25 NTSC 7 5 16ch PAL 6 25 9 KB 15 KB NTSC 30 4ch s Zal 2KB 10 KB Extended Sch NTSC 15 NTSC 30 Both Record PAL 12 5 PAL 25 NTSC 7 5 16ch PAL 6 25 3 KB 15 KB NTSC 0 NTSC 30 PAL 0 PAL 25 os Bell 128Kbps NTSC 1 NTSC 1 DSL PAL 1 abe PAL 1 ale SEH NTSC 4 NTSC 4 PAL 4 a PAL 4 ae Boll 512Kbps NTSC 4 NTSC 4 DSL PAL 4 ote PAL 4 oe Eom User selected User selected User selected User selected User selected 106 DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual 2 The following three tables are offered for users who use DVR 16TS unit 430Q 6U0PF Preset Item Normal PPS Normal Size Event PPS Event Size Event Active D E TT an T 1 mm IP E 16K vee 28 K Both ame eo SSS fax MSC 1 a IL pa ake an ee H BS cm 1 zm eon Se 2 KB one 2KB Both E e sem E zm tom User selected User selected User selected User selected User selected Record Mode Half D1 mode NTSC 720x240 120PPS PAL 720x288 100PPS DVR 4TN 8TN 16TN 16TS 16TT Series Preset Item Normal PPS Normal Size Event PPS Event Size Event Active D TEE T am ee El 12 KB ieee 20 KB Both EE we NCTE ans MSGS Tam ot Sc i zone pm D ce IME f zs eon GEES i SE Stes 2 KB Both Bw se ie se Bom User selected User selected User selected User selected User selected Record Mode
25. Select lt Phone Number gt from Dial out Setup menu and press ENTER A virtual keyboard displays e Use Direction keys to move the cursor for selecting a number e Press ENTER to add the selected number to the phone number entry field e When done press ENTER to save the settings and exit DVR 4TN 8TN 16TN 16TS 16TT Series 67 SPECO TECHNOLOGIES 01 06 68 User s Manual Dial out Account This item enables the user to set the Dial out user name which is needed for dialing out to Internet Service Provider server Contact your network service provider for more specific information To setup the Dial out Account follow these steps Select lt Dial out Account gt from the Dial out Setup menu and press ENTER A virtual keyboard displays Dial out Account v Z o O o a o D gt 0 o H a 16 Z lt 3 N Z 2 O O Q n C lt x lt N lt gt Backspace Delete Cancel OK Use the Direction keys to move the cursor to the desired character Press ENTER to add the selected character to the username entry field When done move the cursor to lt OK gt and press ENTER to save the settings and exit Dial out Password This item allows user to setup the Dial out password Follow these steps to setup the login password Select lt Dial out password gt from Dial out Setup menu and press ENTER A virtual keyboard displays Use Direction keys to move the cursor for selecting a chara
26. Step 3 After choosing the HDD Drive choose the video file that you want to use DVR 4TN 8TN 16TN 16TS 16TT Series 133 SPECO TECHNOLOGIES 01 06 134 User s Manual Step 4 Click the Playback to play the video directly or Export if you want to save the drv file into your PC E DYR Player Yersion 1 0 0 48 E efx Epsce Rl aye D Picture size Data List S 2006 6 13 FE 10 29 28 2006 6 13 GG 10 31 19 2006 6 13 EF 10 41 34 2006 6 13 EF 10 41 57 2006 6 13 FF 11 49 24 2006 6 13 FF 11 49 58 2006 6 13 LT 11 52 19 2006 6 13 ZS 11 55 35 Selection Time 2006 6 13 EF 10 29 28 2006 6 13_EF 10 31 19 Playback Export Figure 2 Select the file you want to use DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 Appendix l IR Remote User s Manual An IR Remote will be attached in the content box and deliver to you with your DVR 4TN DVR 8TN DVR 16TN The keys on the IR Remote are listed as below figure CHANNEL Keys ZOOM ENTER DIRECTION BUTTONS MODE ESC DOME MENU CALL SEQ ees SEARCH int FREEZE SET GO PRESET TOGGLE HINT SCREEN IRIS OPEN ENTER DOME MODE IRIS CLOSE speco technologie DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 ENTER AUTO PAN TILT ESC ZOOM IN FOCUS NEAR ZOOM OUT FOCUS FAR 135 User s Manual Appendix J ezRecord Diagram Sample Diagram Sample Full D1 NTSC 720x480 30PPS PAL 720x576 25PPS
27. TCP IP addresses automatically using DHCP gt or choose lt Specify TCP IP addresses gt and enter the range of IP addresses that you wish to use Once done click lt OK gt to confirm then back to Networking Software menu Click on lt Next gt to continue Incoming TCP IP Properties BEI Network access M Allow callers to access my local area network TCP IP address assignment Q Assign TCP IP addresses automatically using DHCP Specify TCP IP addresses Fone 1922 18 0 1 To 192 168 np 3 Total 3 _ Allow calling computer to specify its own IP address e Click lt Finish gt to complete the process ia New Connection Wizard the following connection Incoming Connections R folder Completing the New Connection A Wizard You have successfully completed the steps needed to create The connection will be saved in the Network Connections To create the connection and close this wizard click Finish lt Back Finish Cancel DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual e The Incoming connection is established S Network Connections stst S e wem e L_Jaed L Fie Edit View Favorites Tock Advanced Help Qax BD P search gt Foes Ex Address Network Connections R g s E Broadband Network Tasks Ei Create a new connection Set up a home or small office network Change Windows Fire
28. The default is lt 9600 gt baud DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual 5 1 7 3 Bits The user can specify the bits in a word that are associated with this protocol The available options are lt 6 gt lt 7 gt and lt 8 gt bits The default is lt 8 gt bits 5 1 7 4 Stop The user can specify the stop bit associated with this protocol Options are lt 1 gt and lt 2 gt stop bits The default is lt 1 gt stop bit 5 1 7 5 Parity This item is used to specify the parity associated with this protocol Options are lt ODD gt lt EVEN gt and lt NONE gt The default is lt NONE gt 5 1 8 Audio Output The item is used to set the audio output mode The available options are as listed as follows lt Live Playback gt Select this item to play the recording sounds of live image in live mode and sounds of recorded video in playback mode respectively lt Always Live gt Select this item to play live sounds in both live mode and playback mode lt OFF gt Select this item to disable the audio output function 5 1 9 Key Beep This item is used to enable or disable the key tone Select lt YES gt to enable the key tone or lt NO gt to disable DVR 4TN 8TN 16TN 16TS 16TT Series 75 SPECO TECHNOLOGIES 01 06 5 2 5 2 1 5 2 2 5 2 3 5 2 4 76 Users Manual Monitor Setup The Monitor Setup menu allows user to set the quality of the displayed image Select lt Monitor Setup gt from the
29. are represented by a character respectively the descriptions are listed in the table below Event type Description Alarm in event Motion detection event i Video loss event DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual 5 6 3 Email Notice The item enables ON disables OFF the Email notification of an event When an alarm event is triggered and lt Email Notice gt is enabled an e mail concerning the alarm event will be sent The default setting is lt OFF gt NOTE In order to send an event notification e mail successfully ensure that the unit connects to the Internet 5 6 4 Event Full Screen This function allows the unit to display the alarm channel in full screen size when an alarm is triggered Select lt None gt to enable this function select lt Main gt to display the alarm channel on Main Monitor when an alarm is triggered select lt Call gt to display the alarm channel on Call Monitor and select lt Both gt to display the alarm channel on both Main Monitor and Call Monitor 5 6 5 Event Duration This item determines the duration of the buzzer and Alarm Out relay function after an alarm is triggered The available event duration range is from 5 second to 999 seconds The default setting is 5 seconds 5 6 6 Per Channel Config This menu is used to set the Video Loss Detect Motion Detect and Alarm In Out function for each channel The menu is disp
30. are the procedures for digital signature verification e Start your SpecoRemote and click lt Play gt on the main window tool bar e Click lt Verify gt tab to display the Verify window Playback Remote Playback Local Playback verify Filename C opgi mmm E Filename avi EE Filename sig Status Log 122 DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual e Click lt Browse gt to select the gpg drv sig files respectively which belong to the exported video you want to authenticate My Recent Documents E Desktop My Documents My Computer My Network Fils name 89641062 gpg SG E Les Files of type GPG files Cancel e Click lt Verify gt to start verifying the digital signature Playback Remote Playback f Local Playback Filename gpg N 20050602 135607 8964 1062 gpg j N 20050602 135607 NORMAL ch01 00 sig Status Log DVR 4TN 8TN 16TN 16TS 16TT Series 123 SPECO TECHNOLOGIES 01 06 User s Manual The result of verification shows in the lt Status Log gt field It returns a GOOD or BAD signature result A GOOD signature indicates the exported clip has not been altered Playback Remote Playback f Local Playback Filename gpg N 20050602 1 3560718964 1062 gpg Filename avi NA20050602 135607 NORMAL ch01 00 avi Filename sig N 20050602 135607 NORMAL chO1 00 sig Status L
31. gt to enable the Dial in function or lt OFF gt to disable Dial in Account This item enables user to protect access to the unit by establishing or changing a dial in user name for modem connection To setup the Dial in Account follow these steps e Select lt Dial in Account gt from Dial in Setup menu and press ENTER A virtual keyboard displays Dial in Account v Z o O CH a o 0 a gt 0 a H ST lt x 3 NZ gt o Ki 2 mm Z lt x lt N lt gt Backspace Delete Cancel OK DVR 4TN 8TN 16TN 16TS 16TT Series 63 SPECO TECHNOLOGIES 01 06 User s Manual e Use Direction keys to move the cursor to the desired character e Press ENTER to add the selected character to the username entry field e When done move the cursor to lt OK gt and press ENTER to save the settings and exit NOTE The Server IP and the Client IP must not be identified as the same IP address but they have to be set in the same domain For example Server IP 192 168 0 1 Client IP 192 168 0 2 Dial in Password This item allows the user to setup the Dial in password Follow these steps to setup the login password e Select lt Dial in password gt from Dial in Setup menu and press ENTER A virtual keyboard displays e Use Direction keys to select character e Press ENTER to add the selected character to the password entry field e When done move the cursor to lt OK gt and press ENTER to s
32. is no need to set further LAN setting therefore the second item lt LAN Setup gt will not be accessible 5 1 6 2 LAN Setup The network related settings in the LAN Setup menu should be associated with the network service type If you select lt LAN gt for lt LAN Select gt then 6 to 8 item will not be available Select lt LAN Setup gt in Network Setup menu and press ENTER for setting the parameters the menu displays as follows LAN Setup 1 DHCP OFF 2 IP 192 168 1 150 3 Netmask 255 255 255 0 4 Gateway 192 168 1 1 5 DNS 0 0 0 0 6 PPPoE Account 7 PPPoE Password 8 PPPoE Max Idle 35min 9 Connect At Booting YES 10 Network Restart NO DHCP This item allows the user to obtain a dynamic IP address from a DHCP Dynamic Host Configuration Protocol server while the unit boots up When using DHCP the settings are dynamic and they will change every time you power up and power off the unit depending on your network s setup DVR 4TN 8TN 16TN 16TS 16TT Series 59 SPECO TECHNOLOGIES 01 06 60 User s Manual If the DHCP is enabled ON a dynamic IP will be assigned to the DVR 4TN 8TN 16TN 16TS 16TT series unit In this case the user does not need to configure a static IP or the Ethernet settings including IP address Netmask Gateway and DNS settings will be read only The default setting is lt ON gt If you are using permanent addressing set DHCP to lt OFF gt for setting the IP Address Netmask Gateway and DNS
33. lt Direction Keys gt In the OSD menu Direction keys are used to move the cursor to previous or next fields UP DOWN are used to change the value in the selected field lt ENTER gt In OSD menu or selection interface press the key to make selection or save settings lt ESC gt Press to cancel or exit from certain OSD menu without saving any changes Key Usage in Virtual Keyboard A virtual keyboard shows when edit the settings such as camera title e mail address etc The virtual keyboard displays as follows i G O w 2 a2 D D o DW gt WY ae AH D E a e Se x lt x 3 N Z lt gt Backspace Delete Cancel OK DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual lt To input characters gt Move the cursor by pressing Direction keys and press ENTER to select characters lt To move the cursor in title entry gt Press MODE and LEFT RIGHT simultaneously to move the cursor to left right in the title entry lt To delete previous character gt Select lt Backspace gt and press ENTER or press MODE and UP simultaneously lt To delete current character gt Select lt Delete gt and press ENTER or press MODE and DOWN simultaneously lt To exit the virtual keyboard gt Select lt OK gt and press ENTER to save the settings and exit or press ESC to exit without saving changes 5 1 System Setup Select lt System Setup gt from the Main Menu and press ENTE
34. menu and save the configuration e For more information on dial out settings see section 5 1 6 4 Dial out Setup 116 DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 PC Configuration User s Manual e Click lt Start gt lt My Network Places gt lt View Network Connections gt and then select lt Create New Connection gt The New Connection Wizard is displayed Click lt Next gt to continue New Connection Wizard Welcome to the New Connection Wizard This wizard helps you Connectto the Internet Connectto a private network such as your workplace network Setup a home or small office network To continue click Next b ack Next gt Cancel e Get up the network connection type Select lt Set up an advanced connection gt and then lt Accept incoming connections gt Click lt Next gt to continue 2 New Connection Wizard 7 Advanced Connection Options Which type of connection do you wantto set up Connect directly to Select the connection type you want Accept incoming connections Allow other computers to connectto this computer through the Internet a phone line ora direct cable connection another computer lt Back Next gt Cancel DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 117 118 User s Manual Choose the modem device that will be used by the PC and click lt Next gt r
35. network such as your workplace network Setup a home or small office network To continue click Next b 3 Next gt Cancel 112 DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual e Set up the network connection type Select lt Connect to the Internet gt and click lt Next gt to continue New Connection Wizard Network Connection Type What do you wantto do Connect to the Internet Connectto the Internet so you can browse the Web and read email Connect to the network at my workplace Connectto a business network using dial up or VPN so you can work from home a field office or another location Set up a home or small office network Connectto an existing home or small office network or setup a new one Set up an advanced connection Connect directly to another computer using your serial parallel or infrared port or setup this computer so that other computers can connectto it C ie e Select lt Set up my connection manually gt and click lt Next gt to continue New Connection Wizard 7 Getting Ready The wizard is preparing to setup your Internet connection How do you want to connectto the Internet Choose from a list of Internet service providers ISPs Set up my connection manually For a dial up connection you will need your account name password and a phone number for your ISP For a br
36. that no overloading of supply circuits or over current protection occurs Main grounding must be reliable and uncompromised by any connections DVR 4TN 8TN 16TN 16TS 16TT Series 3 SPECO TECHNOLOGIES 01 06 User s Manual Table of Contents de EEN entiectcsrsnsttisrcniiessauesddamadiniacaenitdonsidioniiidenatedineaiidamcdendniambuneduiantinnadl 10 t1 Ge Key IAM A cece ec teicce cine heacce cece ceitteeice sect ecudeceucudeatedeuce a RNEER 11 1 2 Product Application EEN 12 Et E 12 2i og 11 81 EE 13 22 Selecting Video FI E 13 2 3 Connecting Devices to the Unit sssini i tanciaiaumecieieniairs 13 2 44 Rear Panel Connections 14 3 General System Setup wcistiicteiieceasetuaisndeiinisadciusivadednnciadaiiadendenaisaienueisedeiunnaieinecendeiuais 17 3 1 Front Panel IER iere nnee ae aana 17 SEH MEER STW deii e ee 18 3 12 EE 19 a2 Msta HDD to eT 22 33 P wer Up Down the Umit EE 23 3 4 Entering OSD Setup leiere 24 3 5 System Date Time Setting E 25 Sa HZ1 9 R 1 9 Ta E 25 3 52 Daylight Saving HEEN 26 3 6 Record Schedule Quality Sethng ccs eee 27 3 61 Record MOJE eee E E nee Cerne eer 27 302 SCheduls e arsan E EE E E E E aE 28 3 6 3 Preset Record COnfigUrAON sgeeseteegrggegeegresgteegEgsegeegEeegbeegEReCeegEe geg 28 3604 PerCamera COA EE 29 3 6 5 To Record Event Video Only sese 30 4 BASIS Op ratiO T sesscicctscicinnccisiiuncurisieniideinnistieiusindetiniradasearedeinivadeiumsessiuacnietnandiawin 30 4 1 Viewing L
37. to play specific video Refer to section 4 3 Searching Recorded Video for more information The Forward or Reverse speed indicator will be shown on the bottom left of the screen when in the playback mode General operation for playback mode is described as follows Key Usage in Playback Key usage changes slightly in playback mode as follows lt LEFT gt Reverse Playback This key is used to reverse recorded video while the unit is playing back Press the key repeatedly to increase the speed of reverse playback by 1x 2x 4x 8x 16x or 32x lt RIGHT gt Forward Playback This key is used to play recorded video on fast forward Press the key repeatedly to increase the speed of forward playback by 1x 2x 4x 8x 16x or 32x lt FREEZE gt Press FREEZE to pause the playback video When the recorded video is paused press LEFT RIGHT to resume playback video as single step reverse forward respectively Press FREEZE again to continue playing video lt PLAY STOP gt Press to start playing back video to exit current mode or stop playing back video and go back to live mode DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual Pause Playback and Single Step Forward To pause and resume recorded video follow these steps e Press one of the CHANNEL keys to display the corresponding camera in full screen e Press PAUSE to pause the current playback image e Press LEFT RIGHT Direction keys t
38. to the desired channel using LEFT RIGHT keys select or de select a channel by pressing ENTER From To Time These items are used to set the time in which data export begins and ends Move the cursor using Direction keys and press ENTER to select the date time items adjust the selected date and time value by UP DOWN keys NOTE The exported data between the Start Time and End Time includes both normal and event video Select Events Select the item to display the event list for exporting event video Move the cursor to scroll through the event list and press ENTER to select the event you want to export Data Type This item is used to select export video type The options are lt Normal gt export normal video only lt Event gt export event video only and lt Both gt export both normal and event video NOTE If you want to export event video only then set the From and To items at the same date and time Otherwise not only the event video but also the normal video included between the From date time and To date time will be exported The drv file can only be played back with SpecoRemote and SpecoPlayer and multiple camera video can be played from one file Note that if multiple channels are exported each channel is exported to a separate file DVR 4TN 8TN 16TN 16TS 16TT Series 39 SPECO TECHNOLOGIES 01 06 4 4 1 3 4 4 1 4 4 4 2 40 User s Manual Digital Signature
39. to the password entry field e When done move the cursor to lt OK gt and press ENTER to save the settings and exit DDNS Setup Dynamic Domain Name System DDNS allows a DNS name to be constantly synchronized with a dynamic IP address In other words it allows those using a dynamic IP address to be associated with a static domain name so others can connect to it by name Once the setting is completed the DDNS address will be http yourhostname ddns iview ddns com Fore example if the chosen Host name is SPECO then the address will be http speco ddns iview ddns com DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual Select lt DDNS Setup gt from Network Setup and press ENTER The menu displays as below figure DDNS Setup 1 Enable DDNS NO 2 Host Name 3 DDNS Port 80 4 Submit Update NO Enable DDNS This item is used to enable or disable the Dynamic Domain Name Service Select lt YES gt to enable the service or lt NO gt to disable Host Name This item allows the user to setup a domain name which is used when entering the DVR 4TN 8TN 16TN 16TS 16TT series unit through the Internet on your remote PC To setup the Host Name of the unit follow the steps e Select lt Host Name gt from DDNS Setup menu and press ENTER A virtual keyboard displays as shown Host Name A BCD G I J M O RS TUVWX Y Z abcde fgh ij l m n o pqr s u v w Xx y Z 012 3 4 5 6 7 8
40. 1 5 7 6 9 15 12 5 28 1 33 7 20 6 24 7 16 2 19 5 13 4 16 1 11 4 13 7 7 5 6 25 56 1 67 3 41 2 49 4 32 5 39 0 26 8 32 2 22 9 27 4 30 25 28 1 33 7 20 6 24 7 16 2 19 5 13 4 16 1 11 4 13 7 15 12 5 56 1 67 3 41 2 49 4 32 5 39 0 26 8 32 2 22 9 27 4 US 6 25 112 2 134 7 82 3 98 8 65 0 78 0 53 7 64 4 45 7 54 9 DVR 4TN 8TN 16TN 16TS 16TT Series 109 SPECO TECHNOLOGIES 01 06 Number of Days of Recording 720 X 240 60PPS without Audio User s Manual Recording Rate Recording Picture Quality Mode Total Total Low Fair Mid High Best Images Perjlmages Per Second Second NTSC PAL NTSC PAL NTSC PAL NTSC PAL NTSC PAL NTSC PAL 5 KB 5 KB 8 KB 8 KB 11 KB 11 KB 14 KB 14 KB 17 KB 17 KB 160 GB Internal Storage 60 50 5 9 7 1 3 7 4 5 2 7 3 3 2 2 2 6 1 8 2 1 30 25 11 8 14 1 T5 9 0 5 5 6 6 4 3 5 2 3 6 4 3 15 12 5 23 5 28 2 15 0 18 0 11 0 13 2 8 7 10 4 7 2 8 6 7 5 6 25 47 0 56 4 29 9 35 9 21 9 26 3 17 3 20 8 14 3 17 2 300 GB Internal Storage 60 50 11 0 13 2 7 0 8 4 5 1 6 2 4 1 4 9 3 4 4 0 30 25 22 0 26 5 14 0 16 8 10 3 12 3 8 1 9 7 6 7 8 1 15 12 5 44 1 52 9 28 1 33 7 20 6 24 7 16 2 19 5 13 4 16 1 TS 6 25 88 2 105 8 56 1 67 3 41 2 49 4 32 5 39 0 26 8 32 2 600 GB Internal Storage 60 50 22 0 26 5 14 0 16 8 10 3 12 3 8 1 9 7 6 7 8 1 30 25 44 1 52 9 28 1 33 7 20 6 24 7 16 2 19 5 13 4 16 1 15 12 5 88 2 105 8 56 1 67 3 41 2 49 4 32 5 39 0 26 8 32 2 US 6 25 176
41. 4 211 6 112 2 134 7 82 3 98 8 65 0 78 0 53 7 64 4 Number of Days of Recording 360 X 240 120PPS without Audio Recording Rate Recording Picture Quality Mode 110 Total Total Low Fair Mid High Best Images Per Images Per Second Second NTSC PAL NTSC PAL NTSC PAL NTSC PAL NTSC PAL NTSC PAL 2 KB 2 KB 5 KB 5 KB 8 KB 8 KB 11 KB 11 KB 14 KB 14 KB oU 5 orage 120 100 7 18 8 62 2 87 3 45 1 8 2 15 1 31 1 57 1 03 1 23 60 50 13 7 16 5 5 9 7 1 3 7 45 2 7 3 3 2 2 2 6 30 25 27 4 32 9 11 8 14 1 7 5 9 0 55 6 6 4 3 5 2 15 12 5 54 9 65 8 23 5 28 2 15 0 18 0 11 0 13 2 8 7 10 4 LS 6 25 109 7 131 7 47 0 56 4 29 9 35 9 21 9 26 3 17 3 20 8 300 GB Internal Storage 120 100 13 8 16 5 5 5 6 6 3 4 4 1 2 5 3 0 2 0 2 4 60 50 25 7 30 9 11 0 13 2 7 0 8 4 5 6 2 4 1 4 9 30 25 51 4 61 7 22 0 26 5 14 0 16 8 10 3 12 3 8 1 9 7 15 12 5 102 9 123 5 44 1 52 9 28 1 33 7 20 6 24 7 16 2 19 5 S 6 25 205 8 246 9 88 2 105 8 56 1 67 3 41 2 49 4 32 5 39 0 DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual 600 GB Internal Storage 120 100 27 9 33 5 11 2 13 4 7 0 8 4 5 1 6 1 4 0 4 8 60 50 51 4 61 7 22 0 26 5 14 0 16 8 10 3 12 3 8 1 g 30 25 102 9 123 5 44 1 52 9 28 1 33 7 20 6 24 7 16 2 19 5 15 12 5 205 8 246 9 88 2 105 8 56 1 67 3 41 2 49 4 32 5 39 0 D 6 25 411 5 493 8 1
42. 76 4 211 6 112 2 134 7 82 3 98 8 65 0 78 0 DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 111 Appendix D Dial up Connections via Modem User s Manual A dial up modem connection allows the user to use the remote software and receive alarm notice without a direct Internet connection Following are the steps for establishing the connection between a DVR 4TN 8TN 16TN 16TS 16TT series unit and a PC Establishing Dial in Connection The Dial in function enables the user to establish dial up modem communication to and from the DVR 4TN 8TN 16TN 16TS 16TT series unit for the remote software use Follow the description to set up your DVR and PC DVR Configuration e Connect a USB modem to the USB socket and connect a working phone line to the modem e Press MENU and input the Administrator password to access the OSD Main menu Select lt Network Setup gt and then lt Dial in Setup gt to set up the Dial In settings including Dial in Account and password etc e For more information on dial in settings see section 5 1 6 3 Dial in Setup PC Configuration e Click lt Start gt lt My Network Places gt lt View Network Connections gt and then select lt Create New Connection gt The New Connection Wizard is displayed Click lt Next gt to continue New Connection Wizard Welcome to the New Connection Wizard This wizard helps you Connectto the Internet Connectto a private
43. 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual Step 3 Install the HDD on your unit _ Second HDD If you want to install only one HDD please adjust the HDD s jumper to Master if you need to install two then adjust one to Master and the other to Slave Note The external HDD should be set to Master default Figure 9 Attach the bracket to the DVR DVR 4TN 8TN 16TN 16TS 16TT Series 129 SPECO TECHNOLOGIES 01 06 User s Manual Figure 10 Close your case Step 4 Confirm if the HDD has been detected After installing your HDD you can turn on the unit and enter the OSD menu for make sure the HDD has been detected the OSD path is Database Setup gt Internal Disks Below lists the table of recommended HDDs Diamond Max Plus 9 80G 160G 300G BS Diamond Max Plus 18 80G 160G 300G Barracuda 7200 7 200G Seagate Barracuda 7200 8 250G 300G 400G Barracuda 7200 10 720G Hitachi Deskstar 7200rpm 60G 300G 400G 500G 130 DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual Appendix H HDD PC Player Tool Introduction For some specific reasons users may need to view the stored data in the HDD on Personal Computer this document guides you how to do that step by step Using EXT2IFS on Your PC EXTZ2IFS an installed File System Driver allows you to run a Linux System on Windows System If you are a Windows
44. C SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSIONNEL This symbol intends to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance This symbol intends to alert the user to the presence of unprotected Dangerous Voltage within the product s enclosure that may be strong enough to cause a risk of electric shock DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual Important Information Before proceeding please read and observe all instructions and warnings in this manual Retain this manual with the original bill of sale for future reference and if necessary warranty service When unpacking your unit check for missing or damaged items If any item is missing or if damage is evident DO NOT INSTALL OR OPERATE THIS PRODUCT Contact your dealer for assistance Rack Mounting Consult with the supplier or manufacturer of your equipment rack for the proper procedure and hardware for mounting this product in a safe fashion Avoid uneven loading or mechanical instability when rack mounting units Make sure the units are installed to get enough airflow for safe operation The maximum temperature for rack mounted units is 104 F 40 C Check product label for power supply requirements to assure
45. CIF mode NTSC 360x240 240PPS PAL 360x288 200PPS Preset Item Normal PPS Normal Size Event PPS Event Size Event Active B c N os T P an Ponien AGEN d 6 KB ere 10 KB Both B Ha T gt e IB T ms zo Se ee as 1 Bea cm MST ze zm Ge 2KB See 2KB Both Baw se M4 se zo User selected User selected User selected User selected User selected SPECO TECHNOLOGIES 01 06 107 User s Manual 3 The following three tables are offered for users who use DVR 16TT unit 43U OPP Preset Item Normal PPS Normal Size Event PPS Event Size Event Active quality pare 2s 19KB az mm PO Moton EE ae 11 KB yee 19 KB Both Bas Tele am Mocs tens eon Ges EE Ee ae me zo S 2KB GC 2KB Both o a se MS se om User selected User selected User selected User selected User selected ord Mode Half D1 mode NTSC 720x240 240PPS PAL 720x288 200PPS Preset Item Normal PPS Normal Size Event PPS Event Size Event Active D TEE T wm ee EE 6 KB Aeris 10 KB Both Bei Tee Meese T mm SSG tons mm ES TI ss IS BW o e IT ze Sa Ge 2 KB SE 2KB Both oz Tase e Tam Sa User selected User selected User selected User selected User selected Record Mode CIF mode NTSC 360x240 480PPS PAL 360x288 400PPS Preset Item Normal PPS Normal Size Event PPS E
46. Data Kee 86 5 4 7 Pre ANlam IRGC Tee DEE 87 S49 Circula PO NS E 87 549 Audio RU DE 87 54 10 Puge Een 88 54101 Purge Al Dala ene eee eee EE EEES 88 54102 Purge All Event Data emer ere een eee ee ee eer ere 88 VO Purge Event BCI cscs ccc nsentteantenctuecteedtnentuadcuacteadtuadtundeie 88 GE Stan tO PUJE eege 88 Sequence Setup EE 89 55 1 Plaid Call Monitor RE 89 5 5 2 Main Call Monitor ZGchedule AAA 89 BEER 90 5601 Intemal E 90 960A ON EE 90 OG Email NotCE ensaia a E 91 5 64 Event 25T E e EE 91 560 5 Event DUO eserita aa raaa 91 566 Per Channel CONi E 91 5 6 6 1 e E E 92 56002 VICES Loss R a e i 92 56 0 3 Motion Detect cinici eieaa ENa 92 9664 Detechon CONi eee erence meena ener tore een earner eer ere 92 Detected Area EE 93 SEMS ieee aeaea 93 DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual Area Threshold EE 93 Detected Area Percentage eeEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEee 93 5609 EECH 94 5666 eebe 94 5 7 Database e siei eni iaie 94 g l Total Free Size of HDD isiende nnii SaLi EDES 95 DC T REG TME esseen EE 95 53 Intemal Extemal DISKS isomerian 95 5 8 Configuration EE 96 9S Load Factory Delati E 96 5 8 2 Import Configuration E 96 59 EXPOM ene 97 5631 Copy Destinato sicrie ee aE EEE EAER 97 5 9 9 2 Contgutatiorn NEE 97 5 8 3 9 Begin E a se 98 50 MACO EE 98 59 1 Select DEV CE E 99 392 e 0 NANNE E 99 9593 ol 2 16 al Sat 100 heh Games 18118
47. Focus Focus Zoom Zoom Dome Open Close Far Near Out In Mode Set Go Preset This key is used to enter the Dome Preset menu to enable the set up of a specific position as a preset and to go to the predetermined preset positions for viewing DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual Toggle Hint Screen This function is used to avoid viewing the dome parameter information while controlling the dome camera Press this key to hide the screen Press it again to redisplay the screen Iris Open Use this function to open the Iris on the dome camera Focus Near Use this function to focus the dome camera near Zoom In Use this function to zoom the dome camera in This enables the user to move closer to the viewing area ESC Use this function to leave dome control mode and return to live and full screen viewing mode Auto Enter e In OSD Menu mode this key is used to make selection e In dome control mode this key is used to activate automatic focus and iris function Iris Close Use this function to close the Iris on the dome camera Focus Far Use this function to focus the selected dome camera far Zoom Out Use this function to zoom the dome camera out This enables the user to move away from the viewing area Pan Tilt Use this function to pan and tilt dome camera DVR 4TN 8TN 16TN 16TS 16TT Series 47 SPECO TECHNOLOGIES 01 06 4 6 5 Setting Preset Points The DVR 4TN 8TN 16TN 16
48. I 18 00 The Weekend End Time indicates the specific time and day that a weekend ends for example MON 06 00 Time is indicated in 1 minute increments Note that the value you have set indicates when the regular Day and Night scheduling ends and Weekend recording begins Preset Record Configuration The lt Preset Config gt is used to select the preset recording quality and frame rate Different default recording quality levels are offered for the user to choose lt Best Quality gt lt Standard gt lt Extended Record gt lt Event Only gt lt ezRecord gt and lt OFF gt According to various Record modes the preset configuration options for normal and event status are described in terms of relative recording rate Picture per Second PPS and recording size for each channel in the table below These preset conditions override any other quality and rate settings The default Preset Configuration setting is lt Standard gt You can refer to Appendix B Record Configuration for detailed information DVR 4TN 8TN 16TN 16TS 16TT Series 83 SPECO TECHNOLOGIES 01 06 5 4 4 5 4 4 1 5 4 4 2 5 4 4 3 84 Users Manual Per Camera Configuration This submenu is used to set the Day Night Weekend PPS Picture per Second and recording quality for each channel The lt Preset Configuration gt must be set to lt OFF gt for accessing these schedules The menu is displayed below is in Record mode 720x240 30PPS in NTSC
49. Key Features The DVR 4TN 8TN 16TN 16TS 16TT series offers advanced features not typically found in standard multiplexers it integrates the full features of a DVR multiplexer and video server by using the software SpecoRemote The key features of the DVR 4TN 8TN 16TN 16TS 16TT series are listed as follows e MPEG 4 high quality compression e 16 channels for video input e Triplex operation enabling simultaneous viewing live or playback while continuing to record e SpecoRemote web based software for remote monitoring and control via LAN or Internet e Embedded Linux operating system e Real time live display for each channel e Recording frame rate up to 480 pps NTSC 400 pps PAL e 2 Channels of audio recording playback e Three USB2 0 ports for video clip export and or backup e Easy software upgrade via USB ThumbDrive CD RW or Internet Remote Application e Up to 4 internal hard drives support up to 1TB capacity e IEEE 1394 for external storage e 2X Digital Zoom available in both live and playback mode e Export video AVI with audio and digital Signature e Exported AVI file can be played in any PC with DIVX decoder installed e Automatic camera detection Plug amp Play e Covert camera operation provides enhanced security and administrator control e Per camera configuration for camera settings frame rate picture bit rate alarms motion detection e Programmable day night weekend scheduling e Program
50. O TECHNOLOGIES 01 06 2 1 2 2 2 3 User s Manual Position the Unit Position mount the DVR 4TN 8TN 16TN 16TS 16TT series unit in an appropriate steady location and make sure the power is off before making any connections The area should avoid hindering or blocking the unit from airflow Enough airflow is needed to protect the unit from overheating The maximum allowable temperature of operating environment is 104 F 40 C The unit utilizes heat conducting techniques to transfer internal heat to the case especially to the bottom side of the unit NOTE Be sure not to remove the rubber feet and always leave a space for air ventilation on the unit s bottom side Selecting Video Format The DVR 4TN DVR 8TN DVR 16TN series unit is designed to operate under either NTSC or PAL video formats Please contact a qualified service person to perform the installation procedure Connecting Devices to the Unit This section lists some important notices that should be read before making any connections to the DVR 4TN 8TN 16TN 16TS 16TT series unit NOTE Connect short term external devices such as USB ThumbDrive USB CD RW USB Hard Disk Drive etc only after the unit is successfully powered up Connecting Required Devices Before powering up you should connect cameras and a main monitor to the unit for basic operation If needed connect a call monitor for displaying full screen video of all installed cameras in sequence
51. Press ENTER to start to export the event video to the connected external device or press ESC to abort AN NOTE The inserted CD will be ejected when its capacity is 99 full 4 5 Deleting Recorded Video The user can delete recorded video in the Purge Data menu The administrator password is required to access the function Select lt Record Setup gt from Main menu once in the Record Setup menu move the cursor to lt Purge Data gt and press ENTER the Purge Data menu is displayed Purge Data 1 Purge All Data NO 2 Purge All Event Data NO 3 Purge Event Before 2000 01 01 4 Start to Purge NO The first three items are used to select the data that you want to purge After selecting the data you want to delete set the forth item lt Start to Purge gt to lt YES gt and press ENTER to start the deleting process The menu items are described below Purge All Data Select this item to delete all normal recorded video from the database Purge All Event Data Select this item to delete all event video from the database Purge Event Before This item is used to delete event video that was recorded before a specific date DVR 4TN 8TN 16TN 16TS 16TT Series 43 SPECO TECHNOLOGIES 01 06 4 6 4 6 1 44 User s Manual Dome Control The DVR 4TN 8TN 16TN 16TS 16TT series unit allows the user to control a dome camera at the front panel In Live mode the user can press the CHANNEL key to display the appropriate dome camer
52. R to enter the System Setup menu System Setup Version Language English Date Time Unit Name DVR Password Network Setup RS485 Setup 8 Audio Output Live Playback 9 Key Beep YES NOOR WN The items found in the System Setup menu are described in the following sections DVR 4TN 8TN 16TN 16TS 16TT Series 51 SPECO TECHNOLOGIES 01 06 5 1 1 5 1 1 1 5 1 1 2 52 Users Manual Version The Version menu allows the user to view system information such as hardware and software versions From the System Setup menu select lt Version gt and press ENTER The following menu is displayed Version Model Name XXXXXXXX Hardware V1 0 Software XXXX XXXX XXXX XXXX Software Upgrade via Local Device Software Upgrade via Internet The items in this menu are described in the following subsections Model Name amp Version The first three items tell the model name and identify the hardware and software version for this unit Software Upgrade via Local Device This item is used for updating the DVR 4TN DVR 8TN DVR 16TN series software by local device The menu is displayed as follows Software Upgrade via Local Device Upgrade Version Select XXXX XXXX XXXX XXXX NO Connect a USB drive that contains the upgrade software to the unit the upgrade files that are available will then be listed in the menu To update the system select a file and use UP DOWN keys to choose l
53. Record Event Video Only If you want your DVR unit to start recording only under the alarm is triggered follow the steps e Enter the OSD setup menu with correct password e Inthe OSD setup menu select lt Record Setup gt menu Move the cursor to the item lt Preset Config gt and select lt Event only gt Refer to Section 5 4 3 Preset Record Configuration for more detailed information Basic Operation The DVR 4TN 8TN 16TN 16TS 16TT series allows the user to easily access some general operations through the front panel The following sections introduce the general operation of the unit Viewing Live Playback Video The general functions in live and playback mode are described in the sections that follow Viewing Modes The DVR 4TN 8TN 16TN 16TS 16TT series supplies the user several ways of viewing both live and recorded video The following descriptions describe the view formats that are available Viewing in Full Screen Press any CHANNEL key directly to view the corresponding camera image in full view format Viewing in Multi window Various multi window view formats are available for selection To switch between these viewing formats press MODE repeatedly DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual The available view formats are illustrated in the following figure Note that 3x3 and 4x4 viewing modes are for DVR 16TN model only WS Full Screen x2
54. S 16TT Series SPECO TECHNOLOGIES 01 06 5 9 6 5 9 7 5 9 8 5 10 User s Manual Digital Signature The Digital Signature function enables the user to export a video clip with the unit s unique signature key It aims to authenticate a video clip exported from the unit and prove it has not been modified The user can export a video clip with or without a digital signature file sig Set the item to lt YES gt to export with the signature file or lt NO gt to export without the signature file Make sure that you have an external storage device such as a USB Hard Drive or USB ThumbDrive available and connected to the appropriate port for export For more information on verifying digital signature see Appendix E Verifying Digital Signature Erase Disc This function is used to remove information found on a CD RW or DVD RW disk prior to exporting new information to the drive Select lt YES gt and press ENTER to start deleting data NOTE This menu item will be grayed out when selected device is not a CD DVD recorder or not select yet Begin Export Select lt YES gt and press ENTER to start exporting Shutdown This item is used to shut down or reboot the unit If you must shut down the DVR 4TN 8TN 16TN 16TS 16TT series unit for any reason please use the proper shut down and power up procedures to avoid damage to your unit Select lt Shutdown gt in Main menu and press ENTER to access the Shutdown menu
55. Screen e Press 1 to access the Set Go Preset function Dome Preset Index Set Preset Go Preset NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO OO JO Om P GO A e Use UP DOWN keys to select the desired preset number from the menu e Change the lt Go Preset gt of the selected preset number to lt YES gt and press ENTER to call the preset point e Now the selected dome camera rotates to the preset position automatically Advanced System Configuration The detailed functions and settings of the DVR 4TN 8TN 16TN 16TS 16TT series can be set by using the hierarchical OSD menu This chapter describes the menu items and options in the OSD menu To enter the Main menu press MENU and then enter Administrator or User password The default passwords are shown in the following table The same default passwords are used for entering the remote viewing software SpecoRemote Administrator Password RB User Password It is strongly recommended to change the passwords to prevent unauthorized access to the unit DVR 4TN 8TN 16TN 16TS 16TT Series 49 SPECO TECHNOLOGIES 01 06 50 User s Manua After entering the correct password the Main menu is displayed Main Menu System Setup Monitor Setup Camera Setup Record Setup Sequence Setup Event Setup Database Setup Configuration Video Export Shutdown G O OO JO Om P G KM A Key Usage in OSD Menu
56. TS 16TT series unit allows user to set preset positions the amount of preset points allowed depends on the dome manufacturer Follow these steps to set preset points 48 User s Manual Press a Channel key to view the corresponding camera in full screen Then press DOME to enter dome control mode Use Direction keys to position the dome camera to desired position Press 2 to view the dome control Hint Screen press 2 again to toggle the Hint Screen Hint Screen DOME ESC Exit MODE PLAY Iris Open Close SEQ FREEZE Focus Near Far MENU SEARCH Zoom In Out ENTER Auto Focus Iris lt A VP Pan Tilt CH1 Set Go Preset CH2 Hint Screen On Off Dome Control Press 1 to access the Set Go Preset function The Dome Preset menu is then displayed Index OANDAARWN Dome Preset Set Preset Go Preset Use UP DOWN keys to select the desired preset number from the menu Change the lt Set Preset gt of the selected preset number to lt YES gt and press ENTER to save the position Now the preset is set and ready to call DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 4 6 6 User s Manual Calling Preset Points Follow these steps to call preset points e Press a Channel key to view the corresponding camera in full screen e Then press DOME to enter dome control mode e Press 2 to view the dome control Hint Screen press 2 again to toggle the Hint
57. TS 16TT series unit is an integrated digital video recorder that combines the features of a time lapse audio video recorder a multiplexer and a video server to create a single security CCTV solution Its outstanding triplex operation enables users to view live or playback recorded video have remote access through network simultaneously while recording other video and to view previously recorded video instantly by entering the time and date or selecting recorded video from the event list The total number of PPS Pictures per Second makes the main difference among these models shown as below table DAs ate G O UVR e UVR O 120 pps 240 pps 480 pps 100 pps 200 pps 400 pps The DVR 4TN 8TN 16TN 16TS 16TT series includes SpecoRemote the remote viewing and configuration software that is a Web browser plug in which allows the user to view live or recorded video images and enables remote configuration The remote software is stored in the DVR 4TN 8TN 16TN 16TS 16TT series unit and deployed over a LAN WAN or Internet connection to remote Windows based computers This simplifies the installation and maintenance of the software components so all remote users are kept up to date DVR 4TN disc ee 0000 gt S GC A DVR 8TN 00000000 c ELLE DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual DVR 16TN 16TS 16TT 0000000000000000 l L R ECAA D e 1 1 Product
58. a in full view To enter Dome Control mode press the DOME key and press channel key 2 to display the hint screen To exit the Dome Control mode and go back to live mode press ESC or DOME To configure the dome control settings see the following sections Dome Connection Follow the steps below to install a dome camera e See section 2 4 Rear Panel Connections for RS 485 port pin definition e Using a RS 485 cable connect the R R terminals from the dome camera to the D D terminals on the RS 485 port respectively Refer to the following illustration Power Video RS 485 Cable DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual 4 6 2 Dome Protocol Setup The Dome Protocol menu item lists the dome protocols available for communicating with dome cameras connected to the DVR 4TN 8TN 16TN 16TS 16TT series unit From the Main menu select lt Camera Setup gt and press ENTER The following menu is displayed Camera Setup 1 Camera Select CH1 2 Dome Protocol None 3 Dome ID 0 4 Camera Title 5 Covert NO 6 Termination NO 7 Brightness 0 8 Contrast 0 9 Saturation 0 10 Hue 0 11 Audio Association Both To configure dome protocol first select a camera then set the communications protocol associated with that dome camera using the Direction keys and press ENTER The available protocols include lt Speco gt lt Pelco D gt lt Pelco P gt lt AD422 gt lt Fastrax 2 gt
59. ackspace Delete Cancel OK e Use Direction keys to position the cursor in the title entry field above the virtual keyboard e Use Direction keys to move the cursor through the lists of characters to the one you need Press ENTER to select a character Continue until the name is established Each title can contain up to 11 characters in it e After the title entry is finished move the cursor to lt OK gt and press ENTER otherwise either press ESC or move the cursor to lt Cancel gt and press ENTER to abort 5 3 5 Covert This function allows the user to choose a specific camera to be covert while the unit is continuing to record video Choosing lt YES gt means to covert the selected camera and lt NO gt the selected camera remains non covert The default setting is lt NO gt DVR 4TN 8TN 16TN 16TS 16TT Series 79 SPECO TECHNOLOGIES 01 06 5 3 6 5 3 7 5 3 8 5 3 9 5 3 10 80 Users Manual To set a camera to be covert follow these steps e Select the channel that you want to be covert from the lt Channel Select gt item e After selecting the channel move the cursor to lt Covert gt item and select lt YES gt Termination This item is used to enable disable the 75 termination resistor inside the unit that adjusts the image quality of each camera lt YES gt termination resistor enabled default lt NO gt termination resistor disabled NOTE If the camera loop out connectors have not b
60. akes effect immediately when the selection is done Press UP DOWN to select from languages listed and press ENTER to confirm DVR 4TN 8TN 16TN 16TS 16TT Series 53 SPECO TECHNOLOGIES 01 06 5 1 3 1 5 1 3 2 54 User s Manual Date Time The user can set the current date time and other OSD parameters in this menu The Administrator s privileges are required for entering the submenu In the System Setup menu select lt Date Time gt and press ENTER the Date Time menu displays as follows Date Time 1 Date 2005 02 21 2 Time 10 39 26 3 Date Time Display 1 Row 4 Date Display Mode Y M D 5 Time Display Mode 24 HR 6 Date Time Order Date First 7 Daylight Saving Time ON 8 DST Start Apr 1 st Sun 02 00 9 DST End Apr Last Sun 02 00 10 DST Bias 60 Min NOTE The reset date time setting applies only to future recorded video the date and time of previously recorded video will not be changed gt AN NOTE After the Date Time setting is changed clearing the database is recommended for avoiding record database corruption Date Time Setting Select lt Date gt or lt Time gt and press ENTER to adjust the settings LEFT RIGHT keys are used to move the cursor to previous or next field ENTER is for selecting and UP DOWN are used to change the value in the selected field Date Time Display Users are allowed to choose to set the Date Time OSD displays in 1 or 2 rows Use the UP DOWN k
61. and lt None gt default NOTE The settings become effective after saving the changes and exiting from the menu 4 6 3 RS485 Setup The DVR 4TN 8TN 16TN 16TS 16TT series unit controls the domes via RS 485 communication protocol The RS 485 parameters in the DVR 4TN 8TN 16TN 16TS 16TT series unit must be set to the same parameters as the protocol used in the RS 422 setup for the dome DVR 4TN 8TN 16TN 16TS 16TT Series 45 SPECO TECHNOLOGIES 01 06 4 6 4 46 User s Manual Users are allowed to change the RS 485_ settings of the DVR 4TN 8TN 16TN 16TS 16TT series unit Select lt System Setup gt in the Main menu then select lt RS485 Setup gt from the System Setup menu and press ENTER The following menu is displayed RS485 Setup 1 Unit ID 224 2 Baud Rate 9600 3 Bits 8 4 Stop 1 5 Parity None The ID number must match the ID address set by the dome The Unit ID is within the range of 1 to 255 The default ID is 224 Note that no two devices on the same bus should be given the same ID address or a conflict may occur The default DVR 4TN DVR 8TN DVR 16TN series RS 485 settings are 9600 Baud 8 Data Bits 1 Stop Bit and No Parity NOTE The settings become effective after saving the changes and exiting from the menu Dome Controlling Key The function keys used in Dome Control are illustrated below Set Go Toggle Hint Enter Auto Preset Screen e 00000000006 0000 Pan Tilt Enter ESC Iris Iris
62. arch event video through the Event List e Press SEARCH to enter the Search menu e To search event video that has been recorded on a specific camera use LEFT RIGHT to move the cursor and press ENTER to select or de select a channel e Move the cursor to lt Event List gt and press ENTER to list the event video from the selected channels The Event List displays e To exit the event list press ESC Follow these steps to playback video from the Event List e Press and hold UP DOWN to scroll through the Event List e Press ENTER to play back the selected event record e Press PLAY STOP to return to live mode 4 4 Video Export The following sections will guide you how to export video through the OSD Setup menu and through the hot keys positioned on the front panel respectively 4 4 1 Export from OSD Setup Menu The Video Export menu enables the administrator to export recorded video with a digital signature to a USB ThumbDrive a CD RW or to DVD RW drive Administrator s password is required to export video The exported video will be identified by the exporting date and time and classified by event type Each recorded video will be exported into four files if exported with digital signature including gpg avi drv sig and readme txt Make sure an external storage device is available and connected to the appropriate port for video export DVR 4TN 8TN 16TN 16TS 16TT Series 37 SPECO TECHNOLOGIES 01 06 4 4 1 1 38
63. are offered for setting Password Admin1 Password User1 Password Admin2 Password User2 Password Adimin3 Password User3 Password Enable Password No Load Factory Password None OO d OO P GKM A Admin User Password s Only who entering with the administrator password is allowed to change the user and administrator passwords to any 4 8 digit number Use the UP DOWN Direction keys to enter the desired account and press ENTER the following menu is displayed Admin Password Press Channel Keys To Enter Password 4 8 Digits Press d To Delete Use CHANNEL keys to input the new password and confirm the new password After setting the new password press ENTER to save the settings and exit Enable Password This item is used to determine if a password is required for accessing the OSD menu Select lt YES gt to demand entering password when accessing the OSD menu if not select lt NO gt DVR 4TN 8TN 16TN 16TS 16TT Series 57 SPECO TECHNOLOGIES 01 06 5 1 5 3 5 1 6 58 User s Manual Load Factory Password This item allows the administrator to reload the factory password incase the administrator cannot remember the password There are three options to select from lt Admin gt reload the Admin password only lt User gt reload the User password only and lt All gt reload the Admin and User passwords The factory password is 1234 for administrator and 4321
64. ave the settings and exit Server IP This item is for setting the IP address that identifies the DVR 4TN 8TN 16TN 16TS 16TT series unit over a modem connection To set the server IP follow these steps e Select lt Server IP gt e Using LEFT RIGHT to move the cursor over the IP and stop where you want to make the change e Press ENTER and then use UP DOWN to change the value e When done press ENTER again to exit e Repeat the procedure until the IP is completely set DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual Client IP This item determines the remote PC s IP address for connecting with the DVR 4TN 8TN 16TN 16TS 16TT series unit To set the Client IP follow these steps e Select lt Client IP gt e Using LEFT RIGHT to move the cursor over the IP and stop where you want to make the change e Press ENTER then use UP DOWN to change the value e When done press ENTER again to exit e Repeat the procedure until the IP is set completely Dial in Idle Time This item indicates the longest amount of time that the modem connection remains active if there is no acknowledgement from the remote pc The value can be set from 0 min to 600 min Dial in Max Time The item indicates the longest amount of time that the connection via modem remains active The value can be set from 0 min to 600 min 5 1 6 4 Dial out Setup The Dial out function enables the user to establish dial up
65. cameras supported by the unit e When in dome control mode the key named 1 is used to access the Set Go preset menu the key named 2 is used to hide or display the dome setting parameters JOG SHUTTLE The jog shuttle knob shown in the figure below is a combination of a shuttle ring with an embedded jog disk which is used to provide wide latitude in playback control Note that the jog shuttle knob is active only when the DVR unit is in Playback mode Shuttle Ring E Jog Disk e While playing back video you can use the shuttle ring to select different speeds of forward and backward playing Rotating the shuttle ring counterclockwise causes the unit to playback in fast forward backward playing speed According to the angle you rotate the shuttle ring you can choose the playing speed from 1x 2x 4x 8x 16x and 32x in both forward and reverse directions shown in the figure below Fast Rewind x1 Fast Forward DVR 4TN 8TN 16TN 16TS 16TT Series 21 SPECO TECHNOLOGIES 01 06 3 2 22 User s Manual e Inside the shuttle ring is the jog disk shown in the illustration below it can turn completely in either direction Once you freeze the video you can use the jog disk to go to single step play back Clockwise rotation causes forward one step playback and counterclockwise rotation causes backward one step playback Backward One step Forward One step Playback Playback Install HDD to the Unit There is a
66. ct channels for export Move the cursor to the desired channel using LEFT RIGHT keys then select or de select a channel by pressing ENTER DVR 4TN 8TN 16TN 16TS 16TT Series 99 SPECO TECHNOLOGIES 01 06 5 9 3 5 9 4 5 9 5 100 User s Manual From To Time The items are used to set the time which data export begins and ends Move the cursor using Direction keys and press ENTER to select the date time items adjust the selected date and time value by UP DOWN keys NOTE When the Start End Time are set remember to select the exporting Data Type Select Events Select this item to display the available event video list for exporting Move the cursor to scroll down the event list and press ENTER to select the event you want to export Data Type The item is used to select export video type The options are lt Normal gt export normal video only lt Event gt export event video only and lt Both gt export both normal and event video NOTE If you want to export selected event video using the item A lt Select Event gt you have to set lt From gt and lt To gt for the same day and time otherwise not only the selected event video will be exported to the selected destination but also any other event video recorded during the period between lt From gt and lt To gt AN NOTE You will not be allowed to access the lt Select Events gt if the Data Type is set to lt Normal gt DVR 4TN 8TN 16TN 16T
67. ct the item and UP DOWN to adjust the value Start to Purge After selecting the video you want to delete or setting the date for deletion set this item to lt YES gt to start the deleting process or choose lt NO gt to cancel DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual 5 5 Sequence Setup The Sequence Setup menu allows the user to set the camera sequence schedule and dwell time for main and call monitor Select lt Sequence Setup gt in Main menu and press ENTER the menu displays as follows Sequence Setup 1 Main Monitor Dwell 5 Sec 2 Main Monitor Schedule 3 Call Monitor Dwell 5 Sec 4 Call Monitor Schedule Items in the Sequence Setup menu are described in the following subsections 5 5 1 Main Call Monitor Dwell The Main Call Monitor can be set to display full screen video for all installed cameras in sequence This item is used to set the Main Call Monitor dwell time which is the amount of time elapsed between switching images The dwell time has an available range of 1 to 120 seconds The default value is 5 seconds 5 5 2 Main Call Monitor Schedule This item is used to set the Main Call Monitor camera sequence in full screen format Move the cursor to lt Main Monitor Schedule gt and press ENTER the menu is displayed as follows Main Monitor Schedule K K K K K K K K K K K K K K K Press 1 16 Key To Select Channel Press d To Delete Follow these steps to se
68. cter Press ENTER to add the selected character to the password entry field When done move the cursor to lt OK gt and press ENTER to save the settings and exit DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 5 1 6 5 5 1 6 6 User s Manual Dial out Idle Time This item indicates the longest amount of time that the modem connection remains active if there is no acknowledgement from the remote pc The value can be set from 1 min to 600 min If selecting lt O gt the modem connection keeps active continuously Dial out Max Time This item indicates the longest amount of time that the connection via modem remains active The value can be set from 1 min to 600 min or lt 0 gt to keep the connection indefinitely Connect When the Dial out related settings are configured set this item to lt YES gt to starting dial out or select lt NO gt to disconnect Trigger Port To avoid the possibility of the default service port port 100 being blocked this item enables the user to change port 100 into another port To change the trigger port move the cursor over lt Trigger Port gt and press ENTER then adjust the setting by UP DOWN keys Email Address This item is used to edit the e mail address where alarm event information will be sent Follow these steps to setup the e mail address e Select lt Email Address gt from Network Setup menu and press ENTER A virtual keyboard displays e Use Direction k
69. de NTSC 720x240 240PPS PAL 720x288 200PPS Normal PPS Normal Quality Event PPS Event Quality NTSC 15 6 KB NTSC 30 PAL 12 5 PAL 25 vole 16CH 3 6 4 Per Camera Configuration This function is used to set the Day Night Weekend PPS Picture per Second and Quality for each channel The Preset Configuration must be set to lt OFF gt for accessing these schedules The menu displays as follows Record Mode 720x240 60PPS in NTSC 720x288 50PPS in PAL Per Camera Config Cameral Select CH1 Day Night Weekend Normal PPS 7 5 7 5 7 5 Normal Qlty Best Best Best Event Max PPS 30 30 30 Event Qlty Best Best Best Event Act Both Both Both e First select a Camera to set its record configuration The image and record settings from the selected camera will be displayed on the screen e Move the cursor using the Direction keys and press ENTER to select an item e Change the value using UP DOWN keys e Press ENTER to confirm the settings or ESC to abort e Press ESC to return to Record Setup menu Please note that the total normal pps for all channels cannot exceed 60 NTSC 720x240 60PPS 50 PAL 720x288 50PPS To increase one channels pps you may have to reduce others first Event pps is not restricted to this rule since a smart event schedule will correct the total pps automatically DVR 4TN 8TN 16TN 16TS 16TT Series 29 SPECO TECHNOLOGIES 01 06 3 6 5 4 1 4 1 1 30 User s Manual To
70. dule Setup 3 Preset Config Standard 4 Per Camera Config 5 ezRecord Setup 6 Data Lifetime 0 Days 7 Pre Alarm Recording 15 Sec 8 Circular Recording ON 9 Audio Recording ON 10 Purge Data 3 6 1 Record Mode The Record Mode is for selecting resolution and recording rate The relative record settings such as preset configuration will follow the record mode setting In normal circumstance we recommend you to select lt 720 x 240 60PPS gt in NTSC format or lt 720x288 50PPS gt in PAL format Move the cursor to lt Record Mode gt and press ENTER then select a Record mode using the UP DOWN keys NOTE After changing the Record Mode setting this warning message This will FORMAT ALL HARDDISKS and LOAD THE FACTORY DEFAULT CONFIG will appear on the screen Press ENTER to confirm the selection The unit will then start to format the hard disks and load the factory default settings or press ESC to abort We strongly recommend that you back up your programmed configuration before making any changes to Record Mode settings DVR 4TN 8TN 16TN 16TS 16TT Series 27 SPECO TECHNOLOGIES 01 06 3 6 2 3 6 3 28 User s Manual Schedule Setup The Schedule Setup is used to set the day night or weekend recording schedule Select lt Schedule Setup gt from the Record Setup menu and press ENTER the following menu is displayed Schedule Setup 1 Day Time Start 06 00 2 Day Time End 18 00 3 Night Time Start 18 00 4 Ni
71. e DVR 4TN 8TN 16TN 16TS 16TT series DVR allows the user to easily access some general operations through the front panel The following subsections introduce general operation of the unit The regularly displayed OSD information and its positions are shown in the following figure The channel title is displayed on the top left side of the window either in full screen mode or in multiple channel mode The current operating mode including Call mode Dome Control mode Playback mode Freeze mode and Sequence mode is displayed on the bottom left side of the screen The date time information is displayed on the bottom right side Ch4 Playback 2005 11 09 PM04 31 22 Front Panel Introduction The unit s front panel controls enable the user to control the unit and preset programmable functions DVR 4TN 8TN 16TN 16TS 16TT Series 17 SPECO TECHNOLOGIES 01 06 User s Manual 3 1 1 LED Definition The DVR 4TN 8TN 16TN 16TS 16TT series LEDs on the front panel are described as follows Power HDD Alarm Network REC e EUKEKKKEEUICKKKER aSOV oeeiuil c Power LED Green The LED should be lit when the power is connected HDD LED Yellow The LED will be lit while the HDD is processing data to or from the connected HDD s Alarm LED Red The LED should be lit when an alarm is triggered Network LED Green The LED should be lit when the DVR 4TN 8TN 16TN 16TS 16TT series unit is connected to a network and b
72. e instead of the built in CD RW DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 4 4 2 1 4 4 2 2 User s Manual Export may take you about 10 minutes to 1 hour depending on the file size of the video ezBurn Introduction Built with the ezBurn technology ezBurn function provides users the easier way to export desired video with CD RW built in or to an external device connected such as an USB ThumbDrive TWO keys SEARCH and COPY and THREE touches are all you need for completing the export The whole exporting process will be done through the front panel but no need to enter the OSD setup menu The ezBurn export process is illustrated on the next page Press Search Key Press COPY Key Press COPY Key Enter Playback Mode Time A Time B The whole process is described step by step in the following sections To Export Normal Video To Export normal video to an external device follow these steps e Press SEARCH and play desired normal video by entering date and time Note if you are viewing in multiple channel mode please make sure there is no window displaying in Live mode Otherwise the export will not work e After entering playback mode play the video and press COPY on the point that you want to set the start point of the export The playback continues DVR 4TN 8TN 16TN 16TS 16TT Series 41 SPECO TECHNOLOGIES 01 06 User s Manual e Press COPY again on the point that you want to set the end po
73. e shown on the screen Press ENTER to confirm the selection then the unit will start to format the hard disks and load the factory default settings or press ESC to abort We strongly recommend backing up your programmed configuration before making any changes on Record Mode settings Schedule Setup This submenu is used to set the day and night time or weekend recording schedule The Night and Day schedules are used to define daytime and nighttime the Weekend schedule is tailored for weekends and holidays Select lt Schedule Setup gt from the Record Setup menu and press ENTER the following menu is displayed Schedule Setup 1 Day Time Start 06 00 2 Day Time End 18 00 3 Night Time Start 18 00 4 Night Time End 06 00 5 Weekend Schedule YES 6 Weekend Start Fri 18 00 7 Weekend End Mon 06 00 DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 5 4 2 1 5 4 2 2 5 4 2 3 5 4 3 User s Manual Day Night Time Start End The Day Night Start Time determines the durion of day night recording time Time is indicated in 1 minute increments The time display format in this menu is based on the setting of Time Display Mode Weekend Schedule The Weekend Schedule determines whether a weekend schedule is in effect Choose lt YES gt to take effect the related weekend settings Weekend Start End The Weekend Start Time indicates the specific day and time that a weekend begins for example FR
74. een used the termination resistor should be enabled for appropriate signal termination Brightness Move the cursor to this item and press ENTER to adjust the brightness of the camera Use UP DOWN keys to adjust the numeric value The range of brightness values is lt 128 gt to lt 127 gt The default setting is lt 0 gt Contrast Move the cursor to this item and press ENTER to adjust the contrast of the camera Use UP DOWN keys to adjust the value Saturation Move the cursor to this item and press ENTER to adjust the color saturation of the camera using UP DOWN keys This value will be ignored on monochrome monitors The range of saturation values is lt 128 gt to lt 127 gt The default setting is lt 0 gt Hue Move the cursor to this item and press ENTER to adjust the hue of the camera Use UP DOWN keys to adjust the value DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 5 3 11 Audio Association This item is used to establish the connection between the selected camera and the two audio in channels Move the cursor to lt Audio Association gt in the Camera Setup menu and press ENTER then select lt Both gt lt Left Only gt lt Right Only gt or lt None gt by UP DOWN keys to set up the connection 5 4 Record Setup The following three factors will effect the total record time of the DVR 4TN 8TN 16TN 16TS 16TT series unit e HDD capacity e Recording rate Picture per Second e Image quality
75. ents Detected Area Percentage This part shows the percentage and variation of the detected volume DVR 4TN 8TN 16TN 16TS 16TT Series 93 SPECO TECHNOLOGIES 01 06 5 6 6 5 5 6 6 6 5 7 94 Users Manual Alarm In This item allows the user to enable disable alarm input detection According to your application select lt N O gt Normal Open or lt N C gt Normal Close to enable the alarm input detection or select lt OFF gt to disable detection The default setting is lt OFF gt NOTE If you set this item to lt N C gt but did not install any device to the unit the alarm will be triggered and the Event Icon will be displayed continually until this item is changed to lt N O gt lt OFF gt or install a device to the unit Alarm Out This item allows the user to assign an alarm on a certain channel to activate the relays These signals can be used to drive a light or siren to caution an alarm event Select from the options lt A Only gt indicates Alarm Out A lt B Only gt indicates Alarm Out B lt A B gt indicates A and B Alarm Out and lt None gt indicates No Alarm Out The default setting is lt None gt Database Setup The menu displays information regarding internal and external disks In the Main menu move the cursor to lt Database Setup gt and press ENTER The following menu is displayed Database Setup 1 Total Size xxx GB 2 Free Size xxx GB 3 Avail REC Ti
76. es SPECO TECHNOLOGIES 01 06 User s Manual 5 1 6 6 Email Address 69 EK e a E 70 SU gre Se Ee H 70 SMTP ONY eege 71 SMTP a 71 HEEN 72 SMIP P AS SWING E 72 516 9 DDNS SEUD E 72 Enable DDNS sse 73 Host NaM G aeiae aia 73 DONS Eeer 74 A e EE 74 517 e 11 e ER dato 74 SKS Hee EE Ee 74 Neca Baud Eege EE Ee 74 Sin Soule aaa oer 75 SrA E 75 aAa PA eea tren tt cares tartan et craven starters terry ta treret 75 518 Audo OUPO EE 75 ok E 75 52 Montor eegend 76 52 1 Show Camera e 1 76 9 2 2 Monitor El e 76 523 Monitor Sy OS E 76 5 2 4 Monitor Chrominance e sees eee eee 76 920 a TER STT PUNE iaeiei aa ea a a aiaa 77 5 26 Show EE eege ee Z 527 VGA ee EE TT 59 e E 78 53 1 Camera EE 78 5 3 2 Dome ENEE estate teste EE 78 599 Dome lD EE 78 5 3 4 Camera Tile esse 79 Re NO E 79 SUS ds Pam 2 10 s EE 80 S9 ue ur EE 80 a E 80 e SWIN eoe E EE 80 SoA lt E 80 e NET FO te Le EEN EN DVR 4TN 8TN 16TN 16TS 16TT Series 7 SPECO TECHNOLOGIES 01 06 5 5 5 6 User s Manual 5 4 Record Setup sese EN 941 Record Tee EE 82 542 Schedule E 82 54 2 1 Day Night ime Start E r ebeebeee bereet 83 5 4 2 2 Weekend Schedule esse eee 83 5 4 2 3 Weekend Start ENQ EE 83 5 4 3 Preset Record Configuration sese eee eee eee 83 5 4 4 Per Camera Communion EE 84 5 4 4 1 Camera Geet 84 5442 Nomal EE 84 5 4 4 3 e e 84 A Event Max PP E 85 5445 EE 85 L Event ACINO EE 85 543 ee ET E 85 5 4 6
77. es wintertime 5 1 3 7 DST Start End These items are used to set the daylight saving duration Use LEFT RIGHT to move the cursor to the next or previous field UP DOWN to change the settings DVR 4TN 8TN 16TN 16TS 16TT Series 55 SPECO TECHNOLOGIES 01 06 5 1 3 8 DST Bias User s Manual This item allows the user to set the amount of time to move forward from the standard time for daylight saving time Available options are lt 30 gt lt 60 gt lt 90 gt and lt 120 gt minutes 5 1 4 Unit Name Users are allowed to assign a name up to 11 characters to the DVR 4TN DVR 8TN DVR 16TN series unit Follow the steps below to edit the unit name e Select lt Unit Name gt from System Setup menu and press ENTER A virtual keyboard displays D o G Q oO a gt lt gt Backspace Cancel OK Unit Name Delete 3 N SZ N e Use Direction keys to move the cursor to the desired character e Press ENTER to add the character to the entry field up to 11 characters e When done move the cursor to lt OK gt and press ENTER to save the settings and exit 56 DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 5 1 5 5 1 5 1 5 1 5 2 User s Manual Password The Password menu allows administrator to change the password settings for accessing the unit Select lt Password gt in the System Setup menu and press ENTER the menu displays as follows Three account password
78. eshold 6 Detected Area Percentage 40 DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual Detected Area Setup The Detect Area is displayed as follows after selecting this item The detection area consists of 273 21x13 detection grids in NTSC video format or 336 21 x16 grids in PAL format Use the Direction keys to move the cursor and press ENTER to enable or disable a grid Press MODE to select all of the grids for detection press MODE again to de select all of the grids Sensitivity This item is used to set the sensitivity of detection grids for the camera A greater value indicates more sensitive motion detection A motion alarm will be triggered once the amount of motion detected exceeds the Threshold value Move the cursor to lt Sensitivity gt and press ENTER and then use UP DOWN keys to adjust the value The value is indicated in 4 increment Area Threshold lt Area Threshold gt means the motion alarm triggered level if the percentage of triggered grids to total detection area is greater than the set value the motion alarm will be triggered For example if 10 grids are selected and the lt Area Threshold gt value is 70 the motion alarm will be triggered when 7 grids are motion detected Move the cursor to lt Area Threshold gt and press ENTER then use UP DOWN keys to adjust the value The value is indicated in 4 increm
79. eys to change the setting The default is to display the date time OSD in one row DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual 5 1 3 3 Date Display Mode This function allows the user to set the OSD display type for the date time There are three options to select from lt Y M D gt lt M D Y gt or lt D M Y gt Y represents Year M represents Month and D represents Day Use UP DOWN keys to change the setting The default setting is lt Y M D gt in both NTSC PAL formats 5 1 3 4 Time Display Mode The user can choose to set the time format to lt 12 hour gt or lt 24 hour gt Use the UP DOWN keys to change the format The default setting is lt 24 hour gt 5 1 3 5 Date Time Order This item is used to set the order of Date Time display to lt Date First gt or lt Time First gt Select this item and press ENTER then use UP DOWN keys to change the setting 5 1 3 6 Daylight Saving Time This item is for people who live in certain regions to observe Daylight Saving Time Select lt ON gt to enable or lt OFF gt to disable the function If the function is disabled the DST Start End time and DST Bias will be grayed out and cannot be accessed If this function is enabled the date time information will be shown on the screen with a DST icon when playing back recorded video or searching video in the event list S indicates summer time and W indicat
80. eys to move the cursor for selecting character e Press ENTER to add the selected character to the password entry field e When done move the cursor to lt OK gt and press ENTER to save the settings and exit DVR 4TN 8TN 16TN 16TS 16TT Series 69 SPECO TECHNOLOGIES 01 06 User s Manual 5 1 6 7 SMTP Setup Simple Mail Transfer Protocol SMTP is a protocol for sending e mail messages between servers SMTP is a relatively simple text based protocol where one or more recipients of a message are specified and the message text is transferred Select lt SMTP Setup gt from Network Setup menu and press ENTER the menu displays as follows SMTP Setup 1 Email via SMTP No 2 SMTP Server 3 SMTP Port 25 4 SMTP Account 5 SMTP Password Email via SMTP This item enables the user to determine if the unit sends e mail via SMTP Select lt YES gt to send e mail via SMTP using direction keys if not select lt NO gt 70 DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual SMTP Server This item enables the user to set the SMTP server Contact your network service provider for more specific information Follow these steps to setup the SMTP Server e Select lt SMTP Server gt from SMTP Setup menu and press ENTER A virtual keyboard displays SMTP Server o O DW o a o D gt WY o H gt G e SS x lt lt 3 N Z S OO Ki Ei vm G lt x lt N
81. for user Network Setup The Network Setup menu allows the administrator to configure the network by specifying the network related settings such as IP address and Netmask etc See your network administrator and or network service provider for more specific information Some settings under the Network Setup menu such as IP and PPPoE Account need to be configured through the virtual keyboard The function key usage pattern is slightly modified please refer to Section 3 4 2 lt Key Usage in Virtual Keyboard gt From the System Setup menu select lt Network Setup gt and press ENTER The following menu displays Network Setup LAN Select LAN LAN Setup Dial in Setup Dial out Setup Trigger Port Email Address 100 SMTP Setup DDNS Setup GO d OO P GKM A Items in this menu are described in the following sections DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual 5 1 6 1 LAN Select PPPoE stands for Point to Point Protocol over Ethernet which is a specification for connecting the users by Ethernet to the Internet through a common broadband medium This item allows you to select your service type between lt LAN gt lt PPPoE gt or lt None gt if you are using an intranet for communication please select lt LAN gt if you are using a broadband medium such as DSL Line or cable modem please select lt PPPoE gt If lt None gt is selected then there
82. ght Time End 06 00 5 Weekend Schedule YES 6 Weekend Start Fri PM18 00 7 Weekend End Mon AM 06 00 e Make appropriate changes for the start time of the Day Time and Night Time schedule using the Direction keys e Press ENTER to confirm the settings or ESC to cancel e If you want to record over the weekend choose lt YES gt to enable the Weekend Schedule in advance and then set the Weekend Start End time e Press ESC to back to previous page Preset Record Configuration The lt Preset Config gt is used to preset recording quality and frame rate for normal record and event record In normal circumstances we strongly suggest you set the item to lt Standard gt the default Below tables show the PPS and picture size under lt Standard gt in Half D1 mode Please refer to Section 5 4 3 Preset Record Configuration for more detailed information DVR 4TN 8TN 16TN Half D1 mode NTSC 720x240 60PPS PAL 720x288 50PPS Normal PPS Normal Quality Event PPS Event Quality NTSC 15 PAL 12 5 NTSC 7 5 TARR NTSC 30 AE PAL 6 25 PAL 25 NTSC 3 75 PAL 3 12 cole coh 4CH 8CH 16CH DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual DVR 4TS Half D1 mode NTSC 720x240 120PPS PAL 720x288 100PPS een Normal PPS Normal Quality Event PPS Event Quality NTSC 7 5 NTSC 30 16CH PAL 6 25 12E PAL 25 20 KE DVR 4TT Half D1 mo
83. he main monitor display area Follow these steps to set the center point e Select lt Screen Center Adjust gt from the Monitor Setup menu and press ENTER The adjusting screen displays as follows Screen Center Adjust A lt gt T e Position the screen center position using the Direction keys e Press ENTER to exit when finished 5 2 6 Show Color Bar Choose this item to display a color bar pattern on the screen The color bar helps to adjust the monitor hue saturation text color and display options Press ESC to exit the color bar pattern and return to the OSD menu 5 2 7 VGA Resolution This item allows the user to select appropriate VGA resolution for the VGA monitor connected to the unit The options are lt 800x600 gt default lt 1024x 768 gt and lt 1280x 1024 gt NOTE If the selected VGA resolution is too high for the monitor the message No Signal will be shown on screen Then please press ESC on the front panel to restore the original setting DVR 4TN 8TN 16TN 16TS 16TT Series 77 SPECO TECHNOLOGIES 01 06 5 3 5 3 1 5 3 2 5 3 3 78 Users Manual Camera Setup The items in the Camera Setup menu enable the user to set camera parameters including camera title dome protocol and ID for each connected camera The menu is shown below Camera Setup 1 Camera Select CH1 2 Dome Protocol None 3 Dome ID 0 4 Camera Title CH1 5 Covert No 6 Termination Yes 7 Brightness 0 8 Contrast 0 9 Sat
84. hen the HDD is full From the Record Setup menu move the cursor to lt Circular Recording gt and press ENTER then select lt ON gt lt OFF gt using UP DOWN keys Audio Recording This item allows the user to enable disable the Audio recording function of the unit When set to lt ON gt audio input is recorded and saved with the video When set to lt OFF gt audio is ignored The default setting is lt ON gt DVR 4TN 8TN 16TN 16TS 16TT Series 87 SPECO TECHNOLOGIES 01 06 5 4 10 5 4 10 1 5 4 10 2 5 4 10 3 5 4 10 4 88 User s Manual Purge Data This item is used to delete the Normal or Event recording video In Record Setup menu move the cursor to lt Purge Data gt and press ENTER the Purge Data menu is displayed Purge Data 1 Purge All Data NO 2 Purge All Event Data NO 3 Purge Event Before 2000 01 01 4 Start to Purge NO Purge All Data This item is used to delete all video from database s Using UP DOWN buttons to select lt YES gt and start the deleting by setting the lt Start to Purge gt to lt YES gt Purge All Event Data This item is used to delete all event video from database s Using UP DOWN keys to select lt YES gt and start the deleting by setting the lt Start to Purge gt to lt YES gt Purge Event Before This item is used to delete event video before a specific date Use LEFT RIGHT keys to move the cursor to next or previous field ENTER to sele
85. ic IP address that identifies the DVR 4TN DVR 8TN DVR 16TN series unit over a modem connection Set the lt Dial out DHCP gt to lt OFF gt for accessing this item Move the cursor over lt Dial out IP gt and press ENTER then press UP DOWN keys to change the values in the selected field DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual Dial out Netmask This item is for setting the Netmask that identifies the DVR 4TN 8TN 16TN 16TS 16TT series unit over a modem connection To configure the item DHCP must be set to lt OFF gt Move the cursor over lt Dial out Netmask gt and press ENTER and then press UP DOWN keys to change the values in the selected field Dial out Gateway Users are allowed to specify the IP address of the gateway or router associated with this unit To configure this item DHCP must be set to lt OFF gt Move the cursor over lt Dial out Gateway gt and press ENTER and then press UP DOWN keys to change the values in the selected field Dial out DNS This item allows the user to specify the IP address of the Domain Name System DNS associated with the unit To configure this item DHCP must be set to lt OFF gt Move the cursor over lt Dial out DNS gt and press ENTER and then press UP DOWN keys to change the values in the selected field Phone Number This item is used to set the dial out phone number Follow these steps to setup the phone number e
86. ideo during alarms 5 4 4 5 Event Qlity This item is used to set the picture size for event status recording Refer to Section 5 4 4 3 for the available options 5 4 4 6 Event Active Users are allowed to choose which alarm type needs to be recorded The available options are lt Alarm gt alarm events lt Motion gt motion detection events lt Both gt alarm event motion detection and lt None gt no events active The default setting is lt Both gt which includes Alarm and Motion event recording 5 4 5 ezRecord Setup This item aims to avoid the complicated record settings and to make the setup much easier Note that this item can be reached only when you select lt ezRecord gt as the option for lt Preset Config gt For more information please refer to the Appendix J ezRecord Diagram Sample Select lt ezRecord Setup gt from lt Record Setup gt and press ENTER the sub menu appears as shown below ezRecord Setup How Many Days To Record 1 Days Daytime Record Yes Night Record Yes Weekend Record Yes Overall Recording Condition Best DVR 4TN 8TN 16TN 16TS 16TT Series 85 SPECO TECHNOLOGIES 01 06 5 4 6 86 User s Manual Follow these steps for ezRecord Setup e Select lt How Many Days To Record gt and press ENTER then press UP DOWN to choose the option you want The maximum days allowed depends on the size of your HDD in the other words the larger the HDD installed the more days the unit can record e Move to
87. ing NOTE Users are not allowed to select any CD R W or DVD RW as a copy destination including built in CD R W and DVD RW 5 8 3 2 Configuration Name This item allows the user to assign the exported configuration file a name Use the virtual keyboard to enter the configuration file name Note that the file name can contain up to 15 characters with no spaces DVR 4TN 8TN 16TN 16TS 16TT Series 97 SPECO TECHNOLOGIES 01 06 5 8 3 3 5 9 98 Users Manual Begin Export Select lt YES gt to begin exporting the configuration file or lt NO gt to abort the export NOTE We strongly recommend users to export configurations before upgrading your system and back it up routinely just in case an unexpected situation occurs Video Export The Video Export menu enables the administrator to export recorded video with a digital signature to a USB Thumb drive a CD RW or to DVD RW drive Make sure an external storage device is available and connected to the appropriate port for video export The Administrator s password is required to export video If the lt Pre Alarm Recording gt function is enabled the event video will be exported into two files including pre alarm video and video recorded after the alarm is triggered Each recorded video will be exported automatically into four files when exporting with a digital signature including gpg avi drv eg and readme txt To export a 1GB file with a digital signature it may ta
88. int of the export Now the ezBurn window displays as shown below The information shown on the window is for read only ezBurn confirmation Selected Device Built in CD RW All data on the disc will be erased Exported Required Size 11 MB Real Export Range From 2005 11 07 AM10 41 13 To 2005 11 07 AM10 41 21 Enter YES ESC NO e Press ENTER to start the export or press ESC to abort e lf there is not any exportable external device connected to the DVR unit then a warning message will be shown on the screen as illustrated below No exportable device detected Please install the target device media to the DVR Enter Retry ESC Exit 4 4 2 3 To Export Event Video To export event video follow these steps e Press SEARCH and play desired event video To play event video refer to Section 4 3 Searching Recorded Video e After entering the playback mode press COPY The ezBurn window displays as shown below The information displayed is for read only ezBurn confirmation Selected Device Built in CD RW All data on the disc will be erased Exported Required Size 11 MB Export Event Info Data Time Ch Type 205 11 07 AM10 42 35 13 Motion Enter YES ESC NO e lf there is not any exportable external device connected to the DVR unit a warning message will be shown on the screen 42 DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual e
89. isplayed Import Config Config Name Select XXXX XXXX NO XXX XX NO Press UP DOWN to select one of the available listed configuration files and choose lt YES gt to start to import DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual NOTE If the imported configuration has a different record mode from the unit s the warning message This config has different record mode This will FORMAT ALL HARDDISKS will show NOTE Remove the ThumbDrive used for importing configuration after the unit restarts or it will be formatted as well 5 8 3 Export Configuration The Administrator is allowed to save a unit configuration by exporting it to an external drive such as a USB Flash Drive Before exporting the configuration make sure the device in which the configuration will be saved is attached to the unit properly Select lt Export Config gt from the Configuration menu and press ENTER The following menu is displayed Export Config 1 Copy Destination 2 Config Name 3 Begin Export NO Items in this menu are described in the following sections 5 8 3 1 Copy Destination Select this item to list available destinations external memory devices to which the configuration can be exported Press UP DOWN to set a destination Please note that saving a different configuration to the same copy destination with the same file name will overwrite the previous configuration file without warn
90. ive Playback Video E 30 S R I LZ Tae B ee L 30 eames 0 E 9 eee rene ree ene a cer ieeer eee trerr ee peer cee een 31 hs Viewmg Live e 31 To Freeze Live Mage E 31 4 1 4 Viewing Recorded Video EE 32 Key Usage in Playback EE 32 Pause Playback and Single Step Forward AAA 33 Viewing Live Image in Playback Mode AAA 33 4 1 5 Dual Main Output For DVR 16TT Only sese eee eee 33 4 2 Sequence EE 34 4 DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual 4 2 1 Sequence on Main Montor sss eee eee 34 4 2 2 Cal Monitor e E 34 4 3 Searching Recorded as sirsiran eaaa eai R EE E 35 43l Seann By E 36 43 2 Searching BY 1 36 AA Mde EXPO EE 37 4 4 1 Export from OSD Setup Menu eee eee eee 37 4 4 1 1 Select the External Device eee 38 4 4 1 2 Select Video for Exporting 2 cccccccccceccncneeeneeeeenenees 39 S e IE IWAN T i 40 EE Eras ow ee ee ee ee ere 40 4 4 2 Quick Video Export through Front Panel sss esse eee eee eee eee 40 4A21 MEU MEHR 41 4 4 2 2 To Export Normal VideO EE 41 4 4 2 3 To Export Event Video esse see 42 4 5 Deleting Recorded MEIER 43 4 6 Ee 44 4o Dome e E 44 4 6 2 Dome Protocol Setup sse esse eee 45 Geht R409 Sep eegene 45 4604 Dome Controlling yt et eet at ata 46 465 Seting Preset ln 48 4 6 6 Calling Preset in 49 5 Advanced System Configuration e veuetsusEEENEEEEESSKEAENEEREREEEEEESENENESEEEEERREEEEUEREKEAEEEEEENEEN 49 Key Le RA E 50 Key Usage in Virtua
91. ke you about 30 minutes From the Main menu select lt Video Export gt and press ENTER The following menu is displayed AN NOTE The inserted CD will be ejected when its capacity is 99 full Video Export 1 Select Device 2 Select Ch CH1 CH2 CH3 CH4 3 From 2005 03 19 AM 07 50 05 4 To 2005 03 28 PM 03 09 18 5 Select Events 6 Data Type Normal 7 Digital Signature NO 8 Erase Disc NO 9 Begin Export NO DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual Items in the menu will be described in the following section 5 9 1 Select Device The external devices that are available for exporting video will be listed by name and free space size in Select Device menu The Select Device menu displays as follows Select Device Device Name Available Sel XXX XXX X X XX 256 MB NO XX XXX XX XXXX 1 5 GB NO The DVR 4TN 8TN 16TN 16TS 16TT series units only support EXT3 file system If you connect an external HDD to the unit ensure that the format of HDD is EXT3 lt Device Name gt This item shows the name of the available device lt Available gt This item shows how much free space is available on the device lt Sel gt Set this item to lt YES gt to set it as an exporting destination or lt NO gt to cancel NOTE This last menu item lt Erase Disk gt will be grayed out when selected device is not a CD DVD recorder or not select yet 5 9 2 Select Channel The item is used to sele
92. l Step 4 Click lt Step1 gt sheet and then choose lt lnstall to System Root gt and lt Start drive on boot gt options When done click lt Install Drive gt button A Ext2FS Install Ext2 FS Step 1 Driver Installation version 0 3 The driver is not installed SR The SystemRoot is the correct location for the Ze Install to SystemRoot driver but because there is a possability that this driver will prevent NT from booting you can install it Install to floppy disk on a floppy disk That way you can remove the driver if NT won t boot If the driver is loaded on boot then it will be immediatly available once you log in to NT Because there is a possability that the driver will C Start driver manually prevent NT from booting you can choose to start it manually once NT is running Install Driver Introduction Stan 1 Windows XP Service Pack 2 Windows NT STE Step 5 Click lt Step2b gt sheet Click lt Drive gt to assign each partition a drive A Ext2FS Install Ext FS Step 2 NT4 Drive Before you can access your Ext2 filesystems from Win32 you letter assignment must assign each partition a drive letter After you have H made the assignments click Save You will have to reboot version 0 3 for the changes to take affect Available partitions My Nevice HarddiskO Partition2 EXT3 No A Device Harddisk1 Partition1 EXT3 Save Assignments Introduction Step 1 Step2a Stan 7h Step 3
93. l Keyboard WE 50 E E s 51 Skl VION E 52 5 1 1 1 Model Name amp Version edd 52 5 1 1 2 Software Upgrade via Local Device sss sss 52 5 1 1 3 Software Upgrade via Internet sss sese eee eee eee eee 53 gd Ser E 53 51 3 Date E 54 Slol Date Eu DE 54 5 1 3 2 Date Time Display sss eee 54 SL Date Display MOda se e ERE 55 51 34 le EE 55 S130 Date Time eT scissor ce eee S steed 55 5 1 36 Daylight Saving MME secs ccs dtcecttecteencendteentuadtuentaadtanctiedeta 55 Skod BST SORT EMI PT 55 DVR 4TN 8TN 16TN 16TS 16TT Series 5 SPECO TECHNOLOGIES 01 06 5 1 4 5 15 User s Manual 51 38 DST Bj S asresten annae araia 56 Uat Ze 56 Paso re EE 57 5 1 5 1 Admin User Passwordset asserts vszscozeazne stara virgi 57 5 152 Enable PASS WE 57 Eu E Re a gs Los E 58 Network OUD ME 58 eu WR SET 59 5 1 6 2 LAN Getup eee 59 eege eege eegener 59 E 60 KE 60 e pee pet he hh T E Teoh 60 SE 61 POE PC E 61 PPPOE eT 1 eas 62 PPPoE Max A TE 62 Connect At ele EE 62 Network Restart E 62 SOS E EE E 62 KI E LEE 63 ul Ee E 63 KIELEN E 64 El 64 Eege 65 Dialin ladle UE 65 Dial in Max Time eegene ee 65 510 4 Diakout Setup E 65 Diakout DHCP isinen aa i hi iniaa 66 WTP seere 66 KI NetMaSK E 67 KEE 67 Dial out IL 67 Phone PU EE edel ebe 67 ee 68 Dial out EE eeben 68 Dial out Idle Time sse eee 69 Dialout M x TWN EE 69 Eege 69 SLOS Moger Eeer 69 DVR 4TN 8TN 16TN 16TS 16TT Seri
94. layed as below Per Channel Config 1 Channel Select CH1 2 Video Loss Detect OFF 3 Motion Detect OFF 4 Detection Config 5 Alarm In OFF 6 Alarm Out None DVR 4TN 8TN 16TN 16TS 16TT Series 91 SPECO TECHNOLOGIES 01 06 5 6 6 1 5 6 6 2 5 6 6 3 5 6 6 4 92 Users Manual Channel Select This item is used to select a desired channel for setting the parameters Move the cursor to lt Channel Select gt and press ENTER then select a channel using UP DOWN keys Press ENTER again to confirm the setting Video Loss Detect This item allows the user to enable disable Video Loss as an alarm event Select lt ON gt to enable Video Loss alarm events lt OFF gt to disable The default setting is lt OFF gt Motion Detect Use to enable or disable the motion detection function of the DVR 4TN 8TN 16TN 16TS 16TT series unit By default the value is lt OFF gt If the motion detection function is enabled it is required to define the motion detection parameters such as detection area and sensitivity settings Detection Config If motion detection function is enabled it is required to define the motion detection parameters such as detection area and sensitivity settings Select a channel for setting the parameters move the cursor to lt Detection Config gt and press ENTER The Detection Configuration menu displays as follows Detection Config 1 Detected Area Setup 2 Sensitivity 88 3 Area Thr
95. link when any data is being transferred REC LED Green The LED should blink while the DVR 4TN 8TN 16TN 16TS 16TT series unit is recording 18 DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual 3 1 2 Functional Keys The DVR 4TN 8TN 16TN 16TS 16TT series unit function keys on the front panel are described below for normal operation ZOOM ENTER CHANNGEL JOG SHUTTLE 0000000000000000 s K COPY CALL DIRECTION DOME ESC MODE PLAY PAUSE SEQ SEARCH MENU STOP COPY Used to quick export video to an external device including USB CD RW and ThumbDrive etc For more detailed operation instructions refer to Section 4 7 1 To Export Video CALL Press to enter call monitor control mode press ESC to exit Direction Keys s In Zoom mode these keys function as Direction keys e Inthe OSD setup menu the Direction keys are used to move the cursor to previous or next fields To change the value in the selected field press UP DOWN keys DOME Press this key to enter dome control mode Please refer to Section 4 6 Dome Control for more details about controlling operation ESC Press to cancel or exit from certain mode or OSD menu without changing the settings made previously DVR 4TN 8TN 16TN 16TS 16TT Series 19 SPECO TECHNOLOGIES 01 06 20 User s Manual MODE Press repeatedly to select desired main monitor display format There are three view modes available full screen 4 window 2x2 and 16 window 4x4
96. lt Action gt This item allows the user to add a storage device to the database or to remove a device from the database The options are lt None gt no action lt Add gt add the selected device into database lt Remove gt remove the selected device from database lt Format gt format the selected device DVR 4TN 8TN 16TN 16TS 16TT Series 95 SPECO TECHNOLOGIES 01 06 5 8 5 8 1 5 8 2 96 User s Manual NOTE Before removing external devices from the unit remember to remove the device from database Configuration The Configuration menu can be used to restore the default factory settings import and export configurations Select lt Configuration gt from the Main menu and press ENTER The following menu is displayed Configuration 1 Load Factory Default NO 2 Import Config 3 Export Config Items in this menu are described in the following subsections Load Factory Default This item is used to load the factory default setting select lt YES gt to recall the factory default setup configuration from the read only memory or lt NO gt to cancel Import Configuration This item allows the user to load a unit configuration that was saved on an external drive To import a configuration that was previously exported make sure the device that saved the configuration is connected to the unit Select lt Import Config gt from the Configuration menu and press ENTER The following menu is d
97. mable main monitor call monitor switching sequence DVR 4TN 8TN 16TN 16TS 16TT Series 11 SPECO TECHNOLOGIES 01 06 1 2 12 User s Manual e Powerful alarm processor allows flexible alarm trigger and responses including alarm motion and camera failure e Dome control protocols Speco Pelco D Pelco P Fastrax 2 and AD422 e Two levels of password security Product Application Diagram Connect the unit with other devices as shown in the system diagram below to complete a video surveillance solution The figure also displays the expandability and flexibility of this digital recording system System Configuration Remote Monitor Control SE Monitor Control an 1 D PC s VGA Monitor Main Monitor Call Monitor Speaker Router Ka SS a RS 485 Control eh ened Ethernet Gm TP 75H i0 E A 75H Alarm Alarm Output t Input D7313 Controller EE KEEN WE ET Cameras 7 k CN Export R qir E N v D L Audio input zb oe USB Thumb Drive DH701 DH801 D7610 Other Brand IEEE 1394 CD RW High Speed Dome Fixed Camera Cameras Disk Array DVD RW System Setup Priority notices and an introduction on system installation will be described in this chapter Please follow the instructions to operate the unit In order to prevent the unit from data loss and system damage that can be caused by a sudden power fluctuation use of an Uninterruptible Power Supply UPS is highly recommended DVR 4TN 8TN 16TN 16TS 16TT Series SPEC
98. me 3Days 7Hrs 4 Internal Disks 5 External Disks 6 NAS Device NOTE If the hard disk detected has failed the message HDD fail will display DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual 5 7 1 Total Free Size of HDD The Total Size of HDD shows the total capacity of the HDD that has been added into database The Free Size of HDD indicates the free space left for recording onto the HDD in database The information is read only 5 7 2 Avail REC Time The Avail REC Time indicates the available duration for recording If the unit is set to record in circular mode the item will show Circular The information is read only 5 7 3 Internal External Disks Select lt Internal Disks gt or lt External Disks gt to see information about the storage devices connected to the unit The submenu is displayed as below Internal Disks Name Active Action XXX XXXXXXX XXXXXX YES None The information about any built in HDD and external storage devices will be listed by model name and status If no storage device connects to the unit the message No Available Items will show on screen NOTE If the file system of the internal HDD is not compatible for the DVR the system will format the internal HDD automatically without notice lt Active gt This item indicates if a storage device is added into the database or not lt YES gt means the device has been added into database
99. ministrator Passwords User Passwords It is strongly recommended that you change the passwords to prevent unauthorized access to the unit After entering the correct password the Main menu is displayed Main Menu System Setup Monitor Setup Camera Setup Record Setup Sequence Setup Event Setup Database Setup Configuration Video Export 10 Shutdown OO JO Om P GKM DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual Move the cursor up down over the OSD items using the Direction keys and press ENTER to enter the selected sub menu 3 5 System Date Time Setting The user can set the current date time and other OSD parameters in the Date Time menu The administrator s privileges are required for entering the submenu In the OSD Main menu select lt System Setup gt and press ENTER then select lt Date Time gt to access the Date Time menu the menu displays as follows Date Time 1 Date 2005 02 21 2 Time PM10 39 26 3 Date Time Display 1 Row 4 Date Display Mode Y M D 5 Time Display Mode 24 HR 6 Date Time Order Date First 7 Daylight Saving Time OFF 8 DST Start Apr 1st Sun 02 00 9 DST End Apr Last Sun 02 00 10 DST Bias 60 Min 3 5 1 Set Date Time Set Date Time Select lt Date gt lt Time gt and press ENTER to adjust the settings LEFT RIGHT keys are used to move the cursor to previous or next field ENTER is f
100. modem communication to and from the DVR 4TN 8TN 16TN 16TS 16TT series unit for remote notification use The user can connect one modem to the DVR 4TN 8TN 16TN 16TS 16TT series unit For more information for dial up setting on PC see Appendix D Dial up Connections via Modem NOTE The Dial out Service is not available if there is no modem connected to the unit DVR 4TN 8TN 16TN 16TS 16TT Series 65 SPECO TECHNOLOGIES 01 06 User s Manual In the Network Setup menu select lt Dial out Setup gt and press ENTER to enter the Dial out menu The menu displays as follows Dial out Setup 1 Dial out DHCP OFF 2 Dial out IP 0 0 0 0 3 Dial out Netmask 0 0 0 0 4 Dial out Gateway 0 D 0 0 5 Dial out DNS 0 0 0 0 6 Phone Number 7 Dial out Account 8 Dial out Password 9 Dial out Idle Time 0 Min 10 Dial out Max Time 0 Min 11 Connect No Dial out DHCP This item allows the user to obtain a dynamic IP address from a DHCP Dynamic Host Configuration Protocol server over a modem connection If the item is enabled ON a dynamic IP will be assigned to the DVR 4TN 8TN 16TN 16TS 16TT series unit In this case the user does not need to configure a static IP and the following settings will be read only Select lt ON gt to enable the DHCP function or lt OFF gt to set the dial out IP address Netmask Gateway and DNS manually The default setting is lt ON gt Dial out IP This item is for setting a stat
101. n empty cartridge positioned on the front panel where the user can install a swappable HDD There are two possible situations when you install a HDD into your DVR e f you install a new HDD the DVR will format it and add it into your database automatically e lf you install a used HDD that does not have the DVR format the DVR will show 1 disk s with wrong data format Please format then add to the database manually Then please follow the steps described below Enter the menu with the administrator privilege and access the lt Database Setup gt section Access the lt Internal or external Disks gt When you see the available disk s select lt format gt to format it After formatting is OK select lt Add gt to add them into your database DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual 3 3 Power Up Down the Unit If you must shut down the DVR 4TN 8TN 16TN 16TS 16TT series unit for any reason use the proper shut down and power up procedures to avoid damage to your DVR unit To Power Up the Unit First check the type of power source available is compatible before plugging in your DVR and turn on the unit using the power switch on the rear panel The color bar and system checking information will be shown on the monitor and disappear when the unit has been completely powered up To Restart Shutdown the Unit Press MENU and input the administrator password to access the OSD Main
102. o move the video as single step reverse forward Press and hold LEFT RIGHT keys to reverse forward the video single step continuously e Press PAUSE again to resume the playback operation Viewing Live Image in Playback Mode Press the MODE key repeatedly in playback mode the 16 window viewing mode contains both live and playback image views This view mode is illustrated below C Live Image CT Playback The eight windows on the top side of the screen play back the Live video from channel 1 to channel 8 respectively The other windows allow the user to view Playback images from channel 1 to channel 8 Dual Main Output For DVR 16TT Only For DVR 16TT users they can use the Call Monitor as the second Main Monitor and access lots of functions such as setup OSD menu and viewing in different mode through the second Main Monitor To perform this function you have to reset a jumper positioned on the Turbo Module inside the unit To use this function the VGA and BNC connectors positioned on the rear panel have to be connected with monitors respectively The VGA monitor is treated as the Main Monitor and BNC monitor the second Main Monitor DVR 4TN 8TN 16TN 16TS 16TT Series 33 SPECO TECHNOLOGIES 01 06 User s Manual Press CALL key for 3 seconds the BNC Monitor will be given the same function as the VGA Monitor except Playback and Search function You can use the BNC Monitor to take over the DVR 16TT unit at the
103. oadband account you won tneed a phone number Use the CD I got from an ISP DVR 4TN 8TN 16TN 16TS 16TT Series 113 SPECO TECHNOLOGIES 01 06 User s Manual e Select lt Connect using a dial up modem gt to connect to the Internet through a phone line and a modem Click lt Next gt to continue r 3 New Connection Wizard Internet Connection How do you wantto connectto the Internet R Connect using a dial up modem This type of connection uses a modem and a regular or ISDN phone line Connect using a broadband connection that requires a user name and password This is a high speed connection using either a DSL or cable modem Your ISP may refer to this type of connection as PPPoE Connect using a broadband connection that is always on This is a high speed connection using either a cable modem DSL or LAN connection Itis always active and doesn t require you to sign in lt Back Next gt Cancel e Type the name of the connection you are creating r 3 New Connection Wizard Connection Name Whatis the name ofthe service that provides your Internet connection Type the name of your ISP in the following box ISP Name DVR Dial In The name you type here will be the name ofthe connection you are creating lt Back Next gt Cancel e Enter the phone number of the modem that is connected to the unit lt New
104. og Verified Good signature from 000089641062 lt GOOD gt Signature Playback Remote Playback Local Playback Filename gpg NAZOOS0602 1 3560789641062 gpg Filename avi NAZOOS0602 1 35607 NORMAL chO1 01 avi Filename sig N 20050602 135607 NORMAL ch01 00 sig Status Log Bad signature Avi file and signature dont match lt BAD gt Signature DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 Appendix F Alarm I O Pin Definition User s Manual The tables below list the pin definitions of alarm I O located on the rear panel of the DVR 4TN 8TN 16TN 16TS 16TT series unit DVR 4TN Alarm I O Definition Definition Definition 1 RS485 D 8 Normal Close 2 15 Reserved 2 RS485 D 9 Common Node 2 16 Reserved 3 Ground 10 Normal Open 2 17 Reserved 4 Normal Close 1 11 Alarm In 1 18 Reserved 5 Common Node 1 12 Alarm In 2 19 Reserved 6 Normal Open 1 13 Alarm In 3 20 Reserved 7 Ground 14 Alarm In 4 21 DVR 8TN Alarm I O LLL Definition Definition Definition 1 RS485 D 8 Normal Close 2 15 Alarmin5 2 RS485 D 9 Common Node 2 16 Alarm ln 6 3 Ground 10 Normal Open 2 17 Alarm In 7 4 Normal Close 1 11 Alarm In 1 18 Alarm In 8 5 Common Node 1 12 Alarm In 2 19 Reserved 6 Normal Open 1 13 Alarm In 3 20 Reserved 7 Ground 14 Alarm In 4 21 DVR 4TN 8TN 16TN 16TS
105. or RS 232 Alarm I O and LAN Audio In Out USB 2 0 LAN Power Switch Power Supply S Video RS 485 1000M x2 x2 Main Monitor S Video BNC VGA S Video BNC and VGA output connectors are available for connecting to a main monitor The main monitor displays live image and playback recorded video in full screen or multiple window format RS 232C The unit provides a RS 232C communication port for sending and receiving signals Alarm UO amp RS485 Port The unit provides an Alarm I O and RS485 port that offers user the flexibility required to connect the unit to another device Refer to Appendix F Alarm I O Pin Definition for detailed pin information on the Alarm UO for the DVR 4TN 8TN 16TN 16TS 16TT IEEE1394 for DVR 4TN 8Tn 16TN only DVR 4TN DVR 8TN DVR 16TN series unit is equipped with two IEEE1394 FireWire ports for extended connections LAN 1000M for DVR 16TS 16 TT only This port is for DVR 16TS 16 TT to connect to a NAS device DVR 4TN 8TN 16TN 16TS 16TT Series 15 SPECO TECHNOLOGIES 01 06 User s Manual Audio In Out The DVR 4TN 8TN 16TN 16TS 16TT series unit provides two channels of audio recording and playback The Audio In RCA connector is offered for connecting an audio source device e g external amplified microphone to the unit The Audio Out RCA connector is available for connecting an audio output device e g amplified speakers to the unit USB 2 0 x3 There are two USB2 0 ports on the rear
106. or selecting and UP DOWN are used to change the value in the selected field NOTE The reset date time setting applies for recording new video the date and time of previously recorded video will not be changed NOTE To avoid record database corruption after changing the date time setting it is recommended to clear the database Date Time Display Users are allowed to choose to set the date time OSD displays in 1 or 2 rows Use the UP DOWN keys to change the setting The default is to display the date time OSD in one row DVR 4TN 8TN 16TN 16TS 16TT Series 25 SPECO TECHNOLOGIES 01 06 3 5 2 26 User s Manual Date Display Mode This function allows user to set the OSD display type of the date time There are three options to select from lt Y M D gt lt M D Y gt or lt D M Y gt Y D 66 represents Year M represents Month and D represents Day Move to the desired item and press ENTER the option starts blinking Use UP DOWN keys to change the setting The default setting is lt Y M D gt in both NTSC PAL formats Time Display Mode The user can choose to set the time format to lt 12 hour gt or lt 24 hour gt Use the UP DOWN keys to change the format The default setting is lt 24 hour gt Date Time Order This item is used to set the order of the date time display to lt Date First gt or lt Time First gt Use UP DOWN keys to change the setting
107. panel and one on the front panel to allow users to connect external USB devices to the unit such as a ThumbDrive The DVR 4TN 8TN 16TN 16TS 16TT allows the user to preset the OSD settings using a USB mouse LAN RJ 45 The DVR 4TN 8TN 16TN 16TS 16TT series is capable of networking The LAN port allows the DVR 4TN 8TN 16TN 16TS 16TT series to access the network Internet through an Ethernet connection Power Supply The DVR 4TN 8TN 16TN 16TS 16TT series includes an AC power connection jack Please use the power supply that ships with the unit WARNING Use of a different power supply may cause overloading AN NOTE Use of other power supply may cause overloading Power Switch Used to power up and shut down the unit Call Monitor BNC The call monitor is used to display full screen video of all installed cameras in sequence The BNC call monitor connector allows the user to connect an optional call monitor to the DVR 4TN 8TN 16TN 16TS 16TT series unit Video Input A group of BNC connectors are available for video input streams from installed cameras The number of connectors is equal to the number of channels the DVR 4TN 8TN 16TN 16TS 16TT units have 4 8 16 BNC connectors on the rear panel respectively DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 3 1 User s Manual Camera Looping Groups of BNC connectors are positioned on the rear panel for looping out video input General System Setup Th
108. same time as if the two monitors are connected to two individual DVR 16TT units When using this function a small figure 5 appears in the mid button side of the two monitors the yellow one represents the monitor is now accessed NOTE When the VGA monitor is now under Dome Control Mode or the OSD setup mode menu 4 2 4 2 1 4 2 2 34 or hasn t exit the OSD menu the BNC monitor cannot access the OSD setup Sequence Setup This section introduce you how to view in sequence mode with both Main Monitor and Call Monitor if connected Sequence function can avoid manually backtracking and give more flexibility while surveillance Sequence on Main Monitor The automatic sequence function can be used in any view mode Select certain view format and press SEQ to toggle the automatic sequential sequence press ESC to stop sequencing The figure below displays the 4 camera sequencing view modes Call Monitor Control Users can use the DVR 4TN 8TN 16TN 16TS 16TT series unit front panel to control a call monitor display without having to access the Main menu Two viewing modes can be displayed on call monitor Sequence display and Single camera display To program the call monitor sequence see section 5 5 Sequence Setup DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual Follow the steps below to control the call monitor e Press the CALL key on the front panel to enter call monitor con
109. se Direction keys to move the cursor for setting the Start Time adjusting the date and time values by UP DOWN keys e Press ENTER to confirm the settings or ESC to abort e Move the cursor to lt Begin Playback gt and press ENTER to start playing back the selected video e Either press PLAY STOP again or ESC to return to live video NOTE If there is no available recorded video that matches your specified time and date the unit starts playback from the next available video NOTE The date time information will be shown on the screen with a DST icon if the Daylight Saving Time function is enabled S indicates summer time and W indicates wintertime Searching by Event Event List allows you to search for desired video by event The Event List is displayed below Event List Date Time Ch Type 2005 03 17 11 26 50 2 Motion 2005 03 17 09 53 03 5 Alarm 2005 03 16 16 14 42 3 Alarm 2005 03 15 03 45 31 1 Motion 2005 03 12 22 27 56 1 Alarm 2005 03 12 10 09 29 7 Motion 2005 03 11 12 18 20 6 Motion 2005 03 10 05 16 00 4 Alarm 2005 03 08 17 11 37 2 Motion 2005 03 08 16 29 10 8 Motion 2005 03 08 03 22 17 2 Alarm The list displays the first 9999 events by date time triggered camera and alarm type As some events are deleted others are displayed The latest recorded event video will be listed on the top DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual Follow these steps to se
110. settings The greater the recording rate and the higher the quality setting the shorter the recording time Most of the related factors can be set here in this submenu The Record Setup menu allows user to set recording quality recording schedules and other recording parameters Administrator s password is required to access Record Setup menu In the Main menu move the cursor to lt Record Setup gt and press ENTER The following menu is displayed Record Setup 1 Record Mode 720x240 60PPS 2 Schedule Setup 3 Preset Config Standard 4 Per Camera Config 5 ezRecord Setup 6 Data Lifetime 0 Days 7 Pre Alarm Recording 15 Sec 8 Circular Recording ON 9 Audio Recording ON 10 Purge Data DVR 4TN 8TN 16TN 16TS 16TT Series 81 User s Manual SPECO TECHNOLOGIES 01 06 5 4 1 5 4 2 82 Users Manual Record Mode This item is for you to preset the resolution and recording rate of normal record and event record The relative record settings such as uration will follow the record mode setting The offered options are lt 720x480 30PPS gt lt 720 x 240 60PPS gt and lt 360 x 240 120PPS gt in NTSC lt 720 x 576 25PPS gt lt 720x288 50PPS gt lt 360x288 100PPS gt in PAL Move the cursor to this item and press ENTER then select a Record mode using UP DOWN keys AN NOTE After changing the Record Mode setting the warning message This will FORMAT ALL HARD DISKS and LOAD THE FACTORY DEFAULT CONFIG will b
111. speco technologies DVR 4TN DVR 8TN DVR 16TN DVR 16TS DVR 16TT Triplex Digital Video Recorder Family With Network DDNS Video Server DVR 4TN 8TN 16TN 16ST 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual DVR 4TN 8TN 16TN 16TS 16TT Series 1 SPECO TECHNOLOGIES 01 06 User s Manual Caution and Preventive Tips Take care not to drop the unit or subject the unit to major shocks or jolts Do not place this unit on an unstable stand bracket or mount This unit is designed for indoor use only Do not place the unit near water or in other extremely humid conditions This unit should not be placed in a built in installation unless proper ventilation is provided Please check the type of power source available before you plug and operate the unit If the clearing is necessary note to plug the unit from the outlet before uncovering the top cover Do not use liquid cleaners or aerosol cleaners Use only a damp cloth for cleaning Always power down the system prior to connecting and disconnecting accessories with the exception of USB devices Lithium battery Danger of explosion if battery is incorrectly replaced Replace with the same type of battery or equivalent type recommended by the battery manufacturer Dispose of used batteries according to the battery manufacturer s instructions Do not block the fan on the bottom of the unit enough airflow is needed to protect the unit from overheating CAUTION RISK OF ELECTRI
112. t YES gt Press ENTER to confirm the selection and start the upgrade process The DVR 4TN 8TN 16TN 16TS 16TT series unit uploads the software updates the system files and reboots automatically The upgrade process may take several minutes to complete After rebooting the unit please check the software version again DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 5 1 1 3 User s Manual NOTE If you want to upgrade your unit with a USB ThumbDrive contains the newest software make sure the software you want to use to update the unit should be fold into a folder named upd 200s otherwise the unit cannot recognize it AN NOTE Power interruption cannot occur during the software upgrade process Ensure that no power interruption can happen until the unit is completely rebooted AN NOTE Do not remove the external USB ThumbDrive CD ROM before the unit has completely shut down hard drive and fan are off Removing the external USB ThumbDrive CD ROM before shut down can cause the system to update improperly Software Upgrade via Internet This item is used to upgrade the unit s software via the internet Select one of the listed software versions and choose lt YES gt The DVR 4TN 8TN 16TN 16TS 16TT series uploads the software updates the system files and reboots automatically Language The Language item allows the user to select the language for the OSD menu and screen messages Language selection t
113. t a sequence e Press LEFT direction key to delete the original setting e Press the desired Channel keys to assign a camera to that location in the sequence e Continue the steps until the sequence is completed DVR 4TN 8TN 16TN 16TS 16TT Series 89 SPECO TECHNOLOGIES 01 06 5 6 5 6 1 5 6 2 90 User s Manual A sequence can have up to 16 entries The user can select fewer than 16 entries for a camera sequence and leave the remaining entries blank The sequence can include a specific camera or cameras multiple times Event Setup This menu allows the user to determine DVR 4TN 8TN 16TN 16TS 16TT series behavior in response to an alarm event In the Main menu move the cursor to lt Event Setup gt and press ENTER The following menu is displayed Event Setup 1 Internal Buzzer ON 2 Event Icon ON 3 Email Notice OFF 4 Event Full Screen 5 Event Duration 6 Per Channel Config Items in the Event Setup menu are described in the following subsections Internal Buzzer This item allows user to enable disable the DVR 4TN DVR 8TN DVR 16TN series internal buzzer If set to lt ON gt the buzzer is activated in response to an alarm If set to lt OFF gt the buzzer is not activated The default setting is lt ON gt Event Icon This item enables ON disables OFF the display of an Event Icon on the main monitor when an alarm event occurs The default setting is lt ON gt enable The event types
114. th 4ch 4KB 28 KB Both 30 KB Both DVR 4TN 8TN 16TN 16TS 16TT Series 105 SPECO TECHNOLOGIES 01 06 User s Manual Record Mode Half D1 mode NTSC 720x240 60PPS PAL 720x288 50PPS Preset Item Normal PPS Normal Size Event PPS Event Size Event Active Ach NTSC 15 PAL 12 5 Best Sch NTSC 7 5 GE 30 NTSC GE Both Alarm Quality PAL 6 25 25 PAL Motion NTSC 3 75 16ch PAL 3 12 25 KB 25 KB NTSC 15 Ach PAL 12 5 Sch NTSC 7 5 SES 30 NTSC AUIS Both PAL 6 25 25 PAL NTSC 3 75 16ch PAL 3 12 15 KB 25 KB NTSC 15 Ach PAL 12 5 Extended NTSC 7 5 SR NTSC 30 SE Kp Record PAL 6 25 PAL 25 NTSC 3 75 16ch PAL 3 12 5 KB 25 KB NTSC 0 NTSC 30 PAL 0 PAL 25 E SE 128Kbps NTSC 1 NTSC 1 DSL PAL 1 ae PAL 1 ae Ee NTSC 4 NTSC 4 PAL 4 lx PAL 4 a SE 512Kbps NTSC 4 NTSC 4 DSL PAL 4 PAL 4 AE ES User selected User selected User selected User selected User selected Record Mode CIF mode NTSC 360x240 120PPS PAL 360x288 100PPS Preset Item Normal PPS Normal Size Event PPS Event Size Event Active ES NTSC 30 L 10 KB 10 KB Best Sch NTSC 15 NTSC 30 Both Alarm Quality PAL 12 5 PAL 25 Motion NTSC 7 5 16ch PAL 6 25 15 KB 15 KB NTSC 30 Ach PAL 25 Sch NTSC 15 BKB NTSC 30 ORE Both PAL 12 5
115. tion Plug amp Play Input RCA x 2 Line In Output RCA x 2 Line Out Recording Mode Always Real Time Record Synchronized w Video Audio Compression Method ADPCM G 726 File Size 8KB Sec Operation Remote VCR mode Playback Only for Video Original Speed Compression Method MPEG 4 Advanced Simple Profile Recording Mode Schedule Alarm Motion Detection Pre Alarm 0 30 sec 720x480 30 pps NTSC 720x240 60 pps Recording Resolution amp Rate E RS so PAL 720x288 50 pps 360x288 100 pps Recording Quality 8 levels presets adjustable Image Size 2K to 20K Byte picture Storage Mode Linear Circular Playback Play Stop Pause Rewind Forward Search Playback Speed Adjustment Yes 1X 2X 32X Play pork Retrieve Date Time Event Data Life Time Yes Programmable Build in Storage X2 ATA 133 UDMA 133 IDE HDD CD RW DVD RW Built in HDD Up to 3 built in HDDs Storage External Storage X2 IEEE 1394 ports Export X3 USB2 0 ports support ThumbDrive CD RW or DVD RW Alarm Input X4 Terminal Block X8 Terminal Block X16 Terminal Block Alarm Detection N C N O Programmable Auditory Alert Built in Buzzer Alarm 21 X 13 NTSC 21 X 16 PAL Grid Array Motion Detection Sensitivity Trig Level Adjustable Video Loss Detection Programmable Alarm Relay Output X2 Terminal Block 1 0A 24V Programmable Communication Network Connectivity Ethernet RJ 45 connector 10 100Mbps supports DHCP PPPoE DDNS Remote
116. trol mode the message Call Mode will then be shown on the bottom left of the screen Press 1 8 Key To Select Channel Press SEQ To Enable Sequence Call Mode e Press CHANNEL key to display the associated camera on the call monitor e Alternatively press SEQ repeatedly to display the sequence of cameras previously programmed in Call Monitor Schedule menu e Press ESC to return to the front panel to the Main monitor control mode 4 3 Searching Recorded Video The DVR 4TN 8TN 16TN 16TS 16TT series is capable of searching and playing back recorded video by date and time or events By entering the specific date and time of the desired video the unit will then search for the matched video and play it on the monitor Alternatively a user can search event video by selecting the channel as well In live or playback mode press SEARCH to enter the Search menu which is shown as follows Search Search By Time From 2005 01 01 00 00 00 End 2005 05 01 00 00 00 Start Time 2005 01 01 00 00 00 Begin Playback Select Channel CH1 CH2 CH3 CH4 Event List DVR 4TN 8TN 16TN 16TS 16TT Series 35 SPECO TECHNOLOGIES 01 06 4 3 1 4 3 2 36 User s Manual Searching by Time Follow these steps to search video by date and time e Press SEARCH key to enter the Search menu the From Time and End Time of the available video is listed on top of the screen The value is unchangeable e U
117. unit searches for the network server and boots up more slowly This network search continues until it times out PPPoE Account This item allows the user to setup the PPPoE login username NOTE For accessing the PPPoE settings select lt PPPoE gt as the Network Type in Network Setup menu To setup the login username follow the steps below e Select lt PPPoE Account gt from the LAN Setup menu and press ENTER A virtual keyboard displays PPPoE Account o O o a o D gt WY o H zs G Sr Ss x lt lt 3 N Z lt gt Backspace Delete Cancel OK e Use Direction keys to move the cursor to the desired character e Press ENTER to add the character to the username entry field DVR 4TN 8TN 16TN 16TS 16TT Series 61 SPECO TECHNOLOGIES 01 06 5 1 6 3 62 User s Manual e When done move the cursor to lt OK gt and press ENTER to save the settings and exit PPPoE Password This item allows the user to setup the PPPoE password Follow these steps to setup the login password e Select lt PPPoE Password gt from LAN Setup menu and press ENTER A virtual keyboard displays e Use Direction keys to select character e Press ENTER to add the selected character to the password entry field e When done move the cursor to lt OK gt and press ENTER to save the settings and exit PPPoE Max Idle This item indicates the time that the modem connection remains active if there is no ackno
118. uration 0 10 Hue 0 11 Audio Association Both Items in this menu are described in the following subsections Camera Select This item is used to select a camera for setting parameters The settings can then be set for the related camera such as dome protocol and camera title Move the cursor to lt Camera Select gt and press ENTER then select a channel using UP DOWN keys Dome Protocol Select the communications protocol associated with your dome camera using the ENTER and Direction keys The available protocol includes lt DynaColor gt lt Pelco D gt lt Pelco P gt lt AD422 gt gt lt Fastrax 2 gt and lt None gt default Dome ID This item is used to assign an ID number to the selected dome camera Note that ID number must match the ID address set by the dome DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual 5 3 4 Camera Title This item allows the user to change the title of each camera connected to the unit By default the titles of cameras are numbered from 1 through 16 respectively The title is displayed on screen after the title changes are set Follow these steps to enter a new title for a camera e Inthe Camera setup Menu move the cursor to Camera Title and press ENTER A virtual keyboard with alphanumeric characters is displayed Camera Title A B C F GH lJ K M N O R S T V W Y Z abcde fgh ij m n o pqr s u v w Xx y Z 012 3 4 5 6 7 8 lt gt B
119. user then you need to install EXT2IFS to your PC before you start using SpecoPlayer to see the drv file To get the software EXT2IFS you can visit http uranus it swin edu au jn linux ext2ifs htm and download EXT2IFS A detailed description about the software also can be found on the website The following steps guide you how to use the EXTZ2IFS software Step 1 Download EXT2IFS to your PC through above website address Step 2 Remove the HDD from your DVR 4TN 8TN 16TN 16TS 16TT series and install the removed HDD into your PC When done reboot the PC Step 3 Extract and Launch EXT2IFS Setup Wizard A Ext2FS Install Ext2 FS vere Sos Newbigin nSt swain edu au Copyright C 2004 John Newbigin vers j on U d 3 http uranus it swin edu au in linux ext2ifs htm Welcome to EXT2IFS Please read this information carefully There is important information that you need to be aware of before you try to use this driver What is EXT2IFS EXT2IFS is an Installable File System Driver IFS for Microsoft Windows NT 4 0 Microsoft Windows 2000 NT 5 0 and Microsoft Windows XP NT 5 1 The driver can read the Second Extended File System EXT 2 and Third Extended File System EXT3 The driver is read only Why would want EXT2IFS f Intrndurtinn 7 Step 1 Step 2a Step 2b Step 3 Windows XP Service Pack 2 Windows NT 5 1 build number 2600 DVR 4TN 8TN 16TN 16TS 16TT Series 131 SPECO TECHNOLOGIES 01 06 User s Manua
120. vent Size Event Active B TEE am ee E 3 KB GE 5 KB Both Be H Im Ice TI me IL zo EES E as 1 mm Ba ne MST zs zm eae 2 KB ea 2KB Both O a se MSA se zo User selected User selected User selected User selected User selected 108 DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual Appendix C Record Duration The record duration relates to recording rate image quality and HDD capacity Refer to the following table NOTE Record duration times are based on actual tests and represent average file sizes Performance may vary depending on specific installations and use Audio recording requires 8 KB per second or 0 7 GB per day for data storage Please refer to our recording time calculator on the Speco website for other possible calculations http www Specotech com gt Support gt Tools Number of Days of Recording 720 x 480 30PPS without Audio Recording Rate Recording Quality Mode Total Total Low Fair Mid High Best Images Per Images Per Second Second NTSC PAL NTSC PAL NTSC PAL NTSC PAL NTSC PAL NTSC PAL 8 KB 8 KB 11 KB 11 KB 14 KB 14 KB 17 KB 17 KB 20 KB 20 KB 30 25 7 5 9 0 5 5 6 6 4 3 5 2 3 6 4 3 3 0 3 7 15 12 5 15 0 18 0 11 0 13 2 8 7 10 4 7 2 8 6 6 1 7 3 7 5 6 25 29 9 35 9 21 9 26 3 17 3 20 8 14 3 17 2 12 2 14 6 UU 5 G 5 orade 30 25 14 0 16 8 10 3 12 3 8 1 9 7 6 7 8
121. wall Dial up settings See Also a Lo Network Troubleshooter Other Places D D Control Panel gd My Network Places My Documents 2 My Computer Local Area Connection 4 regen Cah D v PCMCIA LAN adapter Network Connections System Folder DVR 4TN 8TN 16TN 16TS 16TT Series 121 SPECO TECHNOLOGIES 01 06 User s Manual Appendix E Verifying Digital Signature The digital signature aims to authenticate a video file exported from the unit Follow the instructions to export video with a digital signature and to verify the digital signature To export recorded video with digital signature To export recorded video with a digital signature to a USB hard drive or CD RW drive DVD RW drive follow these steps s In lt Video Export gt menu select copy device data type expected channel and start end time or event video clips e Set the lt Digital Signature gt function to lt YES gt e Start the exporting process by setting lt Begin Export gt to lt YES gt Video Export 1 Select Device 2 Select Ch CH1 CH2 CH3 CH4 3 Start Time 2005 03 19 AM 07 50 05 4 End Time 2005 03 28 PM 03 09 18 5 Select Events 6 Data Type Normal 7 Digital Signature NO 8 Erase Disc NO 9 Begin Export NO Each recorded video will be exported into four files with different filenames including gpg drv sig and readme txt To verify the exported recorded video Following
122. which displays as follows Shutdown 1 Power Off Execute 2 Reboot Execute DVR 4TN 8TN 16TN 16TS 16TT Series 101 SPECO TECHNOLOGIES 01 06 User s Manual Power Off Select this item to shut down the unit Do not remove the power during shut down until the message You can safely turn off DVR now displays Reboot Select this item to reboot the unit The color bar and system checking information are displayed on the monitor until the unit is completely restarted 102 DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual Appendix A Technical Specifications All specifications are subject to change without notice Function 4CH 8CH 16CH Operation System Embedded Linux Video Standard NTSC PAL switch selectable Video Operation Triplex Live Record Playback Remote and Internet access Resolution Live Video NTSC 720 x 480 pixels PAL 720 x 576 pixels Input BNC x BNC x BNC x 4 1 0Vp p 75 ohm 8 1 0Vp p 75 ohm 16 1 0Vp p 75 ohm Video Main Monitor BNC x 1 S Video x 1 1 0Vp p 75 ohm Outputs Call monitor BNC x 1 1 0Vp p 75 ohm Loop BNC x BNC x BNC x 4 1 0Vp p 75 ohm 8 1 0Vp p 75 ohm 16 1 0Vp p 75 ohm VGA Output 800 x 600 1024 x 768 1280 x 1024 pixels 60Hz Picture Refresh Rate c Ge Digital Zoom 2x2 Camera Installa
123. wledgement from the remote PC You can select the idle time from O to 600 minutes The default is 35 minutes Connect At Booting The unit can connect to the Internet automatically when powered up Select lt YES gt to connect at booting otherwise select lt NO gt Network Restart Network restart is required after changing network settings Select lt YES gt to restart the network connection Dial in Setup The Dial in function enables the user to establish dial up modem communication to and from the DVR 4TN 8TN 16TN 16TS 16TT series unit for remote software use The user is allowed to connect only one modem to a DVR 4TN 8TN 16TN 16TS 16TT series unit For more information on dial up setting on PC see Appendix D Dial up Connections via Modem DVR 4TN 8TN 16TN 16TS 16TT Series SPECO TECHNOLOGIES 01 06 User s Manual NOTE The Dial in Service is not available if there is no modem connected to the unit In Network Setup menu select lt Dial in Setup gt and press ENTER to enter the Dial in menu The menu displays as follows Dial in Setup 1 Dial in Service OFF 2 Dial in Account User 3 Dial in Password XXXX 4 Server IP 192 168 0 1 5 Client IP 192 168 0 2 6 Dial in Idle Time 0 Min 7 Dial in Max Time 0 Min Dial in Service If the DVR 4TN 8TN 16TN 16TS 16TT series unit does not connect to the Internet the user can communicate to the unit from a remote PC through a modem as well Select lt ON

Download Pdf Manuals

image

Related Search

Related Contents

JVC pdf Smart Remote Application User Guide  Évaluer l`apprentissage par ordinateur : Tâches et rétroactions      Avaya BCM 4.0 Telset User's Manual  KEOR S 3-10 kVA  Tobii Dynavox I-Series+ Benutzerhandbuch  Origin Storage Dell Inspiron 1720, 1721/Vostro1700 drive    LSI LSI00181  

Copyright © All rights reserved.
Failed to retrieve file