Sony XBR60LX900 Flat Panel Television User Manual
Contents
1. 3D video images on a compatible Sony television e Do not drop or modify these 3D Glasses e If these glasses are broken keep broken pieces away from your mouth or eyes e Keep children away when replacing the battery or opening the battery cover If a child swallows the battery or battery cover consult a doctor immediately Do not dispose of the batteries used in 3D Glasses in a fire e When replacing the battery insert it using the correct orientation e Use only the specified battery for the 3D Glasses Lithium manganese Battery CR2032 e Not for use by children without proper adult supervision e Becareful not to pinch your fingers in hinges of the 3D Glasses when bending the temple frames 19 Troubleshooting The TV will indicate any problems with the STANDBY indicator flashing in red When the STANDBY indicator is flashing The self diagnosis function is activated 1 Count how many times the STANDBY indicator flashes between each three second break For example the indicator may flash three times go off for three seconds then flash again three times 2 Press POWER on the TV to turn it off disconnect the AC power cord and contact Sony Customer Support information provided on the front cover with how many times the indicator flashes When the STANDBY indicator is not flashing 1 Check the items in the tables below Also refer to Troubleshooting in the i Manual 2 If the problem persists conta2. approximately 1 5 N m 15 kgf cm 3 Afier all the screws have been tightened cover the Table Top Stand with the supplied stand rear cover Adjusting the viewing angle This TV can be adjusted within the angles shown below except XBR 60LX900 0 7 6 AL Ano dn uias Remove screw as Install screw into the shown top screw hole of the Table Top Stand qs Lift up and tilt Slide in Fay Reverse the steps when readjusting the angle back to 0 degrees Connecting the TV The following chart shows the high definition HD and standard definition SD video formats supported by your BRAVIA TV inputs PPORTED FORMAT meur veo AUDIO Tua om ur rs ear 1080 24 1080p 10801 720 247 720p 480p 480i When HDMI is connected to DVI with an adapter S a separate Audio L R is Y y Y VY 4 VY VY VY necessary Y Ps Pr Audio L R SD vipEo Q W video Audio L R connection For supported PC formats refer to the i Manual Detaching the terminal cover A e After connecting cables re attach the terminal cover to the TV Shown with a Set Top Box with HDMI Shown with a Set Top Box with connection COMPONENT connection AL Ano dn Buryjas Set Top Box Set Top Box Cable System or VHF UHF Antenna System Cable gt or Antenna Continued 9 Shown with HD BRAVIA Sync Basic Connection Re
3. e Correct hand placement while carrying the TV is very important for safety and to avoid damage ay ae cae e Ensure your TV has adequate ventilation see page 15 e For best picture quality do not expose the screen to direct illumination or sunlight e Avoid installing the TV in a room with reflective wall and floor materials e Avoid moving the TV from a cold area to a warm area Sudden room temperature changes may cause moisture condensation This may cause the TV to show poor picture and or poor color Should this occur allow moisture to evaporate completely before powering the TV on e Ensure that there are no objects in front of the TV IR Sensor 3D Sync Transmitter Intelligent Presence Sensor e Do not expose the Intelligent Presence Sensor to direct sunlight or other strong light as malfunction may occur Attaching the Table Top Stand except XBR 60LX900 Refer to the supplied Table Top Stand instruction leaflet for proper attachment for some TV models 1 Gently slide the TV unit onto the Table Top Stand and align the screw holes A Do not put stress on the LCD panel or the frame around the screen e Be careful to not pinch your hands or the AC power cord when you install the TV unit to the Table Top Stand Bm i 2 Use the supplied screws to attach the TV unit to the Table Top Stand e If you use an electric screwdriver set the tightening torque at
4. SONY LCD Digital Color TV Setup Guide Operating Instructions i MANUAL BRAVIA XBR 60LX900 52LX900 46LX900 40LX900 4 187 898 11 1 Setting up your TV To watch TV Additional Information Sony Customer Support U S A www sony com tvsupport Canada www sony ca support United States Canada 1 800 222 SONY 1 877 899 SONY Please Do Not Return the Product to the Store Owner s Record The information label are located on the rear of the TV They can be found by removing the bottom cover Record model name and serial numbers on the information label in the spaces provided below Refer to them whenever you call upon your Sony dealer regarding this TV Model Name Serial No CAUTION To prevent electric shock and blade exposure do not use this polarized AC plug with an extension cord receptacle or other outlet unless the blades can be fully inserted e Some people may experience discomfort such as eye strain fatigue or nausea while watching 3D video images or playing 3D video games Sony recommends that all viewers take regular breaks while watching 3D video images or playing 3D video games The length and frequency of necessary breaks will vary from person to person You must decide what works best If you experience any discomfort you should stop watching the 3D video images or playing 3D video games until the discomfort ends consult a doctor if you bel
5. a safe place until you are ready to attach the Table Top Stand Keep the screws away from small children cay Read the supplied Safety Booklet for additional safety information Installing the TV Against a Wall or Enclosed Area Make sure that your TV has adequate ventilation Allow enough space around the TV as shown below Avoid operating the TV at temperatures below 41 F 5 C Installed with stand 11 7 ginches 30 cm i 2 3 g inches 6cm i4 inches 10 cm Leave at least this much space around the set 4inches _ 10cm Installed on the wall AL 1no dn uias 117 8 inches 30 cm i 4 inches 10cm N 4 inches 10 cm i Leave at least this much space around the set Never install the TV set as follows Air circulation is blocked Yj Via Air circulation is blocked Vi Y Yu A e Inadequate ventilation can lead to overheating of the TV and may cause damage to your TV or cause a fire 15 To watch TV To watch programs GUIDE OPTIONS HOME LIGHT WIDE 3D POWER Sibi ies i THEATER ansan PLAY e i EzE SYNC MENU PREV STOP NEXT D DVi i MANUAL SCENE TOP MENU MENU CG INTERNET SUBTITLE WIDGETS VIDEO QRIOCITY St eater 1 0 1 Turn on the TV Check the ENERGY SAVING SWITCH setting is on Press POWER on
6. and are used under a license by Gemstar TV Guide International Inc and or its subsidiaries In Canada TV Guide is a registered mark of Transcontinental Inc and is used under a license by Gemstar TV Guide International Inc and or its subsidiaries The TV Guide On Screen system is manufactured under license from Gemstar TV Guide International Inc and or its subsidiaries The TV Guide On Screen system is protected by one or more of the following United States patents 6 498 895 6 850 693 6 396 546 5 940 073 6 239 794 to Gemstar TV Guide International Inc and or its subsidiaries Gemstar TV Guide International Inc and or its related affiliates are not in any way liable for the accuracy or availability of the program schedule information or other data in the TV Guide On Screen system and cannot guarantee service availability in your area In no event shall Gemstar TV Guide International Inc and or its related affiliates be liable for any damages in connection with the accuracy or availability of the program schedule information or other data in the TV Guide On Screen system Blu ray Disc is a trademark BRAVIA and BRAVIA S Force Motionflow BRAVIA Sync and are trademarks or registered marks of Sony Corporation XMB w and xross media bar are trademarks of Sony Corporation and Sony Computer Entertainment Inc PlayStation is a registered trademark and PS3 is a trademark of Sony Comp
7. anel Speaker output 10W 10 W Input Output jacks CABLE ANTENNA 75 ohm external terminal for RF inputs VIDEO IN 1 2 VIDEO AUDIO COMPONENT IN YPBPR Component Video Signal format 480i 480p 720p 1080i 1080p AUDIO HDMI IN 1 2 3 4 HDMI Video 480i 480p 720p 720 24p 1080i 1080p 1080 24p Audio Two channel linear PCM 32 44 1 and 48 kHz 16 20 and 24 bits Dolby Digital AUDIO HDMI IN 2 AUDIO OUT 500 mVrms typical DIGITAL AUDIO OUT OPTICAL PCM Dolby Digital optical signal PC IN D sub 15 pin analog RGB PC HDMI 2 AUDIO IN Stereo mini jack LAN 10BASE T LOOBASE TX connector Connection speed may differ depending on the network environment 1OBASE T 100BASE TX communication rate and communication quality are not guaranteed for this Tv USB DLNA Refer to the i Manual for supported format Power and others Power requirement 110 240 V AC 50 60 Hz U S A Canada 120 V AC 60 Hz Power consumption 3 228 W 185 W 173 W 145 W in use in DAM 25 W 20W You may hear a clicking noise during the download but this is normal in standby Less than 0 12 W with 120 V AC and less than 0 2 W with 240 V AC Screen size inches measured diagonally 60 inches 52 inches 46 inches 40 inches Display resolution 1 920 dots horizontal x 1 080 lines vertical ie with speaker mm a yi box 2 inches Dimensions
8. ar of TV A V Receiver El Blu ray Disc AUDIO OUT VARIFIX DIGITAL AUDIo our OPTICAL 1 a C d BLE HD Cable Box or HD Satellite Receiver m SAT sarm VENET monToR our ANTENNA n Dish 0 gt 79 p z CA Oo 010 Cable cal VIDEO Antenna Signifies a BRAVIA Sync capable device Shown with HD Basic Connection with Home Theater System Side Panel Rear of TV Blu ray Disc DVD MONTOR OUT SVIDEO SD Cable Box or SD Satellite Receiver B aupto our VARIFUA DIGITAL AUDIO OUT OPTICAL cl CABLE ANTENNA Cable D Antenna Home Theater System 10 Shown with PC Connection with SD VCR DVD Side Panel Rear of TV C 3 ji Notebook PC En a BE 500 6 OPTICAL AL Ano dn Buryjas Ea Fane l t Splitter Cable Antenna 11 Securing the TV Sony strongly recommends taking measures to prevent the TV from toppling over Unsecured TVs may to
9. by one or more of the following measures Q Reorient or relocate the receiving antenna Q Increase the separation between the equipment and receiver Q Connect the equipment into an outlet on a circuit Q Consult the dealer or an experienced radio TV technician for help different from that to which the receiver is connected Pursuant to FCC regulations you are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment Safety and Regulatory To prevent radio interference to the licensed service this device is intended to be operated indoors and away from windows to provide maximum shielding Equipment or its transmit antenna that is installed outdoors is subject to licensing Only use Wireless LAN indoors when using it with IEEE 802 1 1a n 5 GHz High power radars are allocated as primary users meaning they have priority of 5250 5350 MHz and 5650 5850 MHz and these radars could cause interference and or damage to this device This device uses 5 GHz band for wireless LAN communication and the maximum gain of the antenna in this device is 6 dBi This equipment complies with FCC IC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body excluding extremities hands wrists and feet This device and its antenna
10. ca registration Software Updates Your TV is capable of receiving software updates For the latest information about software updates for your TV visit United States http www sony com tvsupport Canada http Awww sony ca support NOTE If your TV is connected to the Internet you can check for software updates by selecting Settings Product Support and then Automatic Software Update http www sony net 2010 Sony Corporation Printed in U S A 4187898111
11. ct Sony Customer Support information provided on the front cover Condition Explanation Solution Picture There is no picture screen Check the antenna cable connection is dark and no sound e Connect the TV to the AC power and press POWER on the TV e If the STANDBY indicator lights up in red press TV POWER on the remote control Tiny black dots and or e The screen is composed of pixels Tiny black dots and or bright bright dots appear on the dots pixels on the screen do not indicate a malfunction screen General The TV s power cannot be Check to see the mark on the ENERGY SAVING SWITCH turned on is pressed The TV turns off e Check if the Sleep Timer Timer or Idle TV Standby is automatically the TV activated enters standby mode The Auto Shut off function may be set to On If Auto Shut off is activated and TV receives no signal the TV will automatically enter standby mode in 15 minutes Check Auto Shut off is activated under Eco feature of this TV e Check if Presence Sensor in Eco is activated The remote does not e Replace the batteries function e Your TV may be in SYNC mode Press SYNC MENU select TV Control and then select Home Menu or Options to control the TV The TV and its surrounding When the TV is used for an extended period of time the TV and become warm its surround may become warm to touch This is not malfunction of the TV The Parental Lock e En
12. eatures Watching TV Using the Home Menu Fun Features with Connected Equipment Parts Description Troubleshooting Index Fun Features with Connected Equipment Introduces how to connect and enjoy optional equipment E Parts Description E Troubleshooting You can find solutions for your problems E Index e Images and illustrations may differ from what you see on your TV Continued 17 AL yoqem OL E To use 3D Glasses Before use Remove the battery s insulating sheet before using the 3D Glasses for the first time p P Parts and components 1 Slide switch Set the switch for a comfortable fit Set both the switches on either side for a comfortable fit Close the temple frames slightly inwards to set the switch Increases the width of the glasses Lo L fi N Decreases the width of the glasses 2 Battery cover Detach the cover when replacing the battery 3 LED indicator Flashes one time every 3 seconds Power on Flashes three times every 3 seconds Low battery Battery capacity is almost running out Flashes three times Power off 18 Pouch 2 4 IR sensor Receive signals from the 3D Sync Transmitter This part receives IR infrared rays from the Transmitter IR s entry angle differs according to distance or usage environment e Please keep this face clean 5 Power button Power on Press once Power off Hold po
13. enna connected directly to the back of document will help you get the most out of your TV your TV Visit www antennaweb org for more information on antenna selection and setup e Discover the wealth of entertainment now available on super high resolution Blu ray Disc player and other Sony HD equipment Please take a moment to register your TV at U S A http productregistration sony com Canada http www SonyStyle ca registration Four Steps to a Full HD Experience Set Source Sound and Setup 3 Sound 1 Set Complete the high definition experience with a BRAVIA Sync surround sound system or A V Now that you have made the best selection in LCD TV receiver from Sony technology be sure to remove all accessory contents from the packaging before setting up your TV 4 Setup 2 Install your TV and connect your sources See page 8 Source for sample connection diagrams To help assure the To experience the stunning detail of your BRAVIA TV highest quality for your HD experience use Sony you need access to HD programming HDMI High Definition Multimedia Interface cables e Upgrade your signal or content source to high definition To learn more about HDTV visit HD by contacting your HD service provider U S A http www sony com HDTV Canada http www SonyStyle ca hd This TV displays all video input signals in a resolution of 1 920 dots x 1 080 lines Checking the accessories AC power cord 1 Re
14. eseaeseaeeseaeeseaeeeeeeaees 6 Connecting ithe TVsr sanear asee ae a dae E eeeindeesis sce ele ek ee oe 8 SOCUFING He TV EE itive Bele a cet ts a ee ec ha ce et a 12 Organizing the AC power cord eeeececeseeeseeeseeeeeeeeaeeteaeeeseeesaeeeaeeseaeessaeseaeeeaeesaeesaeeseaeessaeeeaeeae 13 Running initial Setup ric eieren aaee aeaa dtd a Na VE TEE A Ea a Si 14 Detaching the Table Top Stand from the TV eeesseeseeseesseeseeeeneesresirsersteninstrttnntentnnrnsenseneen 14 Using a Wall Mount Bracket ssasssessesesssraerennennnnrrnarnnarrunnrnunartnacntnnnnaneraannanactnacenaacernacnnuennaae nna 15 Installing the TV Against a Wall or Enclosed Area s sssssesssessreesrresrrresirreriiesrinssrinsrirnerirnsrnnnsren 15 To watch TV To watch programs donnera Gili aa i kd a dee nee ee 16 TO USEANG TV feature Sinsin a aa ae a eaten dens 16 To useiMan al cciana ice edie a eee vie a E N EA 17 ORTDA EEA AEE N a T E E T 18 Additional Information Tr ubleShooting erii eid Ea a a ee ashe tel E 20 Specifications iss iie ir eare ia cued iee re dees enee aa iar fea o N R A 22 e Operating instructions are built into your BRAVIA TV Refer to To use i Manual for operation page 17 e Retain this manual for future reference The BRAVIA Full HDTV Experience Thank you for choosing Sony Your new BRAVIA TV e Receive over the air HD broadcasts with an HD opens the door to the Full HDTV Experience This quality ant
15. ieve necessary You should also review i the instruction manual of any other device or media used with this television and ii our website www sony com tvsupport for the latest information The vision of young children especially those under six years old is still under development Consult your doctor such as a pediatrician or eye doctor before allowing young children to watch 3D video images or play 3D video games Adults should supervise young children to ensure they follow the recommendations listed above e When using the simulated 3D function please note that the displayed image is modified from the original due to the conversion done by this television e Operate the TV only on 110 240 V AC U S A Canada 120 V AC e Avoid operating the TV at temperatures below 41 F 5 C Licensing Information Macintosh is a trademark of Apple Inc registered in the U S and other countries HDMI the HDMI Logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries Fergason Patent Properties LLC U S Patent No 5 717 422 U S Patent No 6 816 141 2 Manufactured under license from Dolby Laboratories Dolby and the double D symbol are trademarks of Dolby Laboratories In the United States TV Guide and TV Guide On Screen are registered trademarks of TV Guide Entertainment Group Inc and or its subsidiaries or affiliates
16. mote control 1 Size AAA batteries 2 Table Top Stand 1 except XBR 60LX900 Fixing screws for Table Top Stand M5 x 16 4 except XBR 60LX900 Assembling screws for Table Top Stand M5 x 16 4 XBR 40LX900 only Bottom cover 1 Stand rear cover 1 4 Black spacers 4 gt XBR 52 46 40LX900 only Silver spacers 4 gt XBR 60LX900 only Screws M6 x 20 4 gt XBR 60LX900 only 3D Glasses battery included 2 Pouch for 3D Glasses 2 Please refer to the model name printed on the remote control 2 XBR 40LX900 requires assembling Refer to other leaflet to assemble the Table Top Stand 3 For XBR 60LX900 the bottom cover is factory attached to the TV 4 For XBR 60LX900 the stand rear cover is factory attached to the Table Top Stand 5 These screws and spacers are required when installing an optional Wall Mount Bracket You must use these screws instead of the ones provided with the bracket for safety reasons Be sure to keep them in a safe place until you are ready to use the Wall Mount Bracket See page 23 for the recommended Wall Mount Bracket for your TV Inserting batteries into the remote control Remove the protection sheet Push and slide the cover upward Guidelines for Remote Control e Point your remote control directly at the IR sensor located on your TV e Make sure that no objects are blocking the path between the remote control and the IR sensor on
17. n you switch the TV on for the first time the Language menu appears on the screen 4 Follow the instructions on the screen The ENERGY SAVING SWITCH must be on to set the clock and obtain program information for the TV Guide e Home mode sets the TV to settings optimized for home viewing this setting is ENERGY STAR compliant 5 Select Continue to scan for available channels and enable the TV Guide On Screen feature If you receive channels from a cable box or satellite receiver and do not wish to use the TV s built in tuner select Skip Selecting Skip will disable the TV Guide On Screen feature which is only available when the TV s tuner is used A e If you skip the channel scan while in the setup menus TV Guide will be disabled 14 Detaching the Table Top Stand from the TV Remove only the screws marked with 4 on the TV A e Remove the stand rear cover and bottom cover prior to detaching the Table Top Stand e Do not remove the Table Top Stand for any reason other than to install corresponding accessories on the TV When installing the TV on a wall remove the four screws from the rear of the TV They are fastened in the screw holes for wall mounting Be sure to store the removed screws in a safe place keeping them away from children When attaching the Table Top Stand again be sure to fasten the four screws previously removed to the original holes on the
18. pple and result in property damage serious bodily injury or even death Preventing the TV from Toppling Secure the TV to a wall and or stand Do not allow children to play or climb on furniture and TV sets Avoid placing or hanging items on the TV Never install the TV on slippery unstable and or uneven surfaces furniture that can easily be used as steps such as a chest of drawers Install the TV where it cannot be pulled pushed or knocked over Route all AC power cords and connecting cables so that they are not accessible to curious children 12 Recommended Measures to Secure the TV Consider the following measures when securing your TV to a Stand not supplied 1 Secure the Stand for the TV Make sure the Stand can adequately support the weight of the TV Use two angle braces not supplied to secure the stand For each angle brace use the appropriate hardware to e Attach one side of the angle brace to the wall stud e Attach the other side to the Stand Angle brace not supplied Stand 2 Secure the TV to the Stand Use the optional hardware listed below not supplied e M4 x 16 machine screw screwed into the TV s Table Top Stand e A screw or similar attach it to the Stand e Rope or chain strong enough to support the weight of the TV Make sure that there is no excess slack in the rope or chain An alternative way to secure the TV is with an optional Sony Su
19. pport Belt Kit M4 x 16 machine screw _ not supplied Rope or chain V not supplied wy Y Table Top Stand Screw not supplied Screw hole on the Contact Sony Customer Support to obtain the optional Support Belt Kit by providing your TV model name e For United States call 1 800 488 7669 or visit www sony com accessories e For Canada call 1 877 899 7669 3 Anchor the TV to the Wall Anchor the TV to the wall by using bolts wall anchor and chain or rope Anchor bolts not supplied Rope or Wall chain mount SS not holes supplied Wall anchor not supplied Your TV is shipped with screws attached to the rear of the TV They are fastened in the screw holes for wall mounting Be sure to remove the upper two screws prior to anchoring the TV on a wall e Securing the TV to the stand without securing the TV and the stand to the wall provides minimum protection against the TV toppling over For further protection be sure to follow the three measures recommended Organizing the AC power cord e After the AC power cord is installed as illustrated attach the bottom cover 13 AL Ano dn buras Running initial setup 1 Complete your cable connections before proceeding with the Initial Setup Connect the TV to your nearest power outlet 2 Check the ENERGY SAVING SWITCH setting is on 3 Press POWER on the TV Whe
20. rear of the TV Using a Wall Mount Bracket Your TV can be mounted on a wall using a Wall Mount Bracket not supplied out of the box as packaged If the Table Top Stand is attached to the TV the TV may require detaching the Table Top Stand see Detaching the Table Top Stand from the TV page 14 Prepare the TV for the Wall Mount Bracket before making cable connections For product protection and safety reasons Sony strongly recommends that you use the Wall Mount Bracket designed for your TV and the installation should be performed by a Sony dealer or licensed contractor e Follow the instruction guide provided with the Wall Mount Bracket for your model Sufficient expertise is required in installing this TV especially to determine the strength of the wall for withstanding the TV s weight e Be sure to use the screws supplied with the Wall mount bracket when attaching the mounting hooks to the TV set The supplied screws are designed so that they are 8 mm to 12 mm in length when measured from the attaching surface of the mounting hook The diameter and length of the screws differ depending on the Wall mount bracket model Use of screws other than those supplied may result in internal damage to the TV set or cause it to fall etc 8 12 mm ere Screw supplied with the Wall mount bracket Mounting Hook Hook attachment on rear of TV set e Be sure to store the unused screws and Table Top Stand in
21. rogrammed the function button DVD AMP STB will blink twice if not it blinks five times Confirm the Programming If you can turn your equipment on and off using the green POWER button the programming is complete If not try the next code listed s e In some cases you may not be able to program your remote control If this is the case use your equipment s own remote control Any of the function buttons DVD AMP STB can be programmed to operate other equipment regardless of the labeling For example if programmed with the correct code a Blu ray Disc player can be operated with the DVD button This is useful if your equipment does not match any of the labeled buttons To reset the remote control to the factory default Press SCENE TV POWER and simultaneously The four function buttons DVD AMP STB and TV blink when successfully reset Setting up your TV Some TV models are packaged with a detached Table Top Stand so you can mount your TV to a wall right away If you are not mounting the TV to a wall you will need to attach the Table Top Stand You will need a Phillips screwdriver and the supplied screws to complete the task Look for the supplied Table Top Stand instruction leaflet Be sure to consider the following while setting up your TV e Disconnect all cables when carrying the TV e Carry the TV with the adequate number of people larger size TVs require two or more people
22. s must not be co located or operating with any other antenna or transmitter except Grant condition Note This television includes a QAM demodulator which should allow you to receive unscrambled digital cable television programming via subscription service to a cable service provider Availability of digital cable television programming in your area depends on the type of programming and signal provided by your cable service provider Compatible Optional Accessories Information Use the following Sony optional accessories with uo eunoju j euOHIPpY E your TV model Sony Model No XBR 60LX900 52LX900 46LX900 40LX900 Sony Wall Hanging Bracket SU WH500 Model No Sony Wall Mount Bracket Model No SU WL500 SU WL700 Use with other optional accessories may cause instability and could result in property damages or injury For instructions on using the Wall Mount bracket with your TV please go to http esupport sony com for your TV model and download Additional Information for Using Sony Wall Mount Bracket To Customers Sufficient expertise is required for TV installations Be sure to subcontract the installation to a Sony dealer or licensed contractor and pay adequate attention to safety during the installation 23 For Your Convenience Online Registration Be sure to register your TV United States http productregistration sony com Canada http www SonyStyle
23. ter 4357 for the PIN code PIN code 4357 is always accepted password has been forgotten 20 How to Care for Your BRAVIA Safety is very important please read and follow the safety documentation Safety Booklet separately provided Unplug the TV and other connected equipment from the wall outlet before you begin cleaning your TV e Wipe the LCD screen gently with a soft cloth e Stubborn stains may be removed with a cloth slightly moistened with a solution of mild soap and warm water e If using a chemically pretreated cloth please follow the instruction provided on the package e Never use strong solvents such as a thinner alcohol or benzine for cleaning Do not plug in the TV into the wall outlet until the moisture from cleaning has evaporated The TV should also be placed on a stable surface to prevent it from toppling over see page 12 If you have young children or pets at home check regularly to insure the TV is securely fastened 21 uo eunoju j jeuonippY E Specifications Model name XBR 60LX900 52LX900 46LX900 40LX900 System Television system NTSC American TV standard ATSC 8VSB terrestrial ATSC compliant 8VSB QAM on cable ANSI SCTE 07 2000 Does not include CableCARD functionality Channel coverage Analog terrestrial 2 69 Digital terrestrial 2 69 Analog Cable 1 135 Digital Cable 1 135 Panel system LCD Liquid Crystal Display P
24. the TV or TV POWER on the remote control to turn on the TV You may use the TVI button located on the front or back of the remote control Select a TV channel CH O L To use the Guide Press GUIDE to display the TV Guide On Screen to view scheduled programs or to select a program to watch Press again to exit the Guide Use with 0 9 and ENT to select digital channels For example to enter 2 1 press 2 C Gg and ENT To use the TV features Press HOME to display TV Home Menu XMB to access TV Settings and other media and network related content 16 Press OPTIONS to display a list of convenient functions and menu shortcuts The Options menu items vary based on current input and or content es To use i Manual TV POWER LIGHT WIDE 3D POWER aa THEATER azan PLAY e i COR SYNCMENU PREV STOP NEXT CO o 2 BD sD DVD SCENE TOPMENU MENU ae Welcome to i Manual E BRAVIA TV Features E Watching TV Introduces convenient features such as TV Guide Favorites etc E Using the Home Menu You can find how to customize your TV settings etc A Your BRAVIA TV comes with an on screen manual To learn more about your TVs features you can access your i Manual with the touch of a button 1 Press i MANUAL MANUAL 2 Press 0 lt gt to navigate and select items amp Manual Welcome to i Manual BRAVIA TV F
25. uter Entertainment Inc DLNA the DLNA Logo and DLNA CERTIFIED are trademarks service marks or certification marks of the Digital Living Network Alliance FACE DETECTION logo is trademark of Sony Corporation DTV HIGH DEFINITION TELEVISION Homi O1 DOLBY DIGITAL Update T V TV GUIDE S dina Your BRAVIA TV is ENERGY STAR qualified in the Home mode It meets strict energy efficiency guidelines set by the U S Environmental ENERGY STAR Protection Agency and Department of Energy ENERGY STAR is a joint program of these government agencies designed to promote energy efficient products and practices 3 Changes to certain features settings and functionalities of this TV i e TV Guide Picture Sound Light Sensor Power Savings can increase or change the power consumption Depending upon such changed settings the power consumption may exceed the limits required for the ENERGY STAR qualification in the Home mode gt The illustrations of the remote control used in this manual are of the RM YD036 unless otherwise stated Table of Contents Checking the accessories c 2 cciescyse elda evant ests ose a a A E aa 4 Inserting batteries into the remote control ee eeeeeeesneeeeeeeeeeeneeeeeeeeeeeneeeeeaeeeeeeaeeeeeaaeeeeneeeeteneeees 4 Setting up your TV Attaching the Table Top Stand cececceseseceseesceeeaeeeeeseaeeeseeseseeseaeseaeeceeeseaeeesa
26. w x h x d 7 1 8 x 1 5 8 x 7 1 4 inches 179 x 40 x 183 mm 22 Declaration of Conformity Trade Name SONY Model XBR 60LX900 XBR 52LX900 XBR 46LX900 XBR 40LX900 Responsible Party Sony Electronics Inc Address 16530 Via Esprillo San Diego CA 92127 U S A Telephone Number 858 942 2230 This device complies with part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation For customers in Canada This Class B digital apparatus complies with Canadian ICES 003 FCC Related Information This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference
27. wer button down for 2 seconds Auto power off More than 5 minutes without IR signal 6 Nose pad Adjust the nose pad for a comfortable fit 7 Temple frames You can bend adjust the temple frames for a comfortable fit Replacing the battery If the LED indicates low battery power replace the battery Use a CR2032 battery Open the battery cover 2 i Pugh hero est 7 stay SE an angle 4 Lip Leo Sz Coin etc CE Align the mark and the fi mark AL yoqem OL E fay When opening or closing the battery cover make sure the coin etc is properly inserted in the groove of the battery cover Precautions for use e The 3D Glasses are operated by receiving infrared rays from the Transmitter Mis operation may occur if The 3D Glasses do not face the 3D Sync Transmitter If there are objects blocking the path between the 3D Glasses and the 3D Sync Transmitter If there are other infrared communication devices or lighting equipment residential heating equipment IR transceiver etc nearby e Watch the TV using the 3D Glasses facing squarely towards the TV e 3D effect is inadequate and screen color will be shifted with lying down position or leaning your head e To preserve our environment dispose of used batteries according to your local laws or regulations Safety precautions e You should only use the 3D Glasses for watching
28. with stand mm 1 440 x 938 x 380 1 261 x 838 x 400 1 127 x 761 x 320 994 x 686 x 290 inches 56 3 4x 37x 15 46 3 4 x 33 x 15 3 4 4437 3 x 30x 127 38 39 4x27 ex 11 1 2 without stand mm 1 440 x 906 x 64 1 261 x 804 x 64 1 127 x 727 x 64 994 x 652 x 64 inches 56 3 4x 353 4x25 8 463 4x 3174x278 443 8 x 28 53 8 x 27 8 39 4 x 25 3 4 x 2 5 8 wall mount hole pattern mm 400 x 300 300 x 300 wall mount screw size mm M6 length refer to diagram on page 15 Mass with stand kg Ib 49 8 109 7 36 2 79 8 28 4 62 6 23 7 52 3 without stand kg Ib 42 8 94 3 30 2 66 6 24 6 54 2 20 3 44 8 Supplied accessories See Checking the accessories page 4 Optional accessories Connecting cables Support Belt Kit Wall Mount Bracket Wall Hanging Bracket 3D Glasses TDG BR100 BR50 1 For LAN connections use a Category 7 10BASE T 100BASE TX cable not supplied 2 Download Acquisition Mode DAM is used for software updates and or collecting data for TV Guide On Screen Optional accessories availability depends on its stock e Design and specifications are subject to change without notice 3D Glasses TDG BR100 Weight 2 7 oz 77 g including battery Battery type CR2032 3V Battery life Up to 100 hours of battery life The battery life will vary based on usage patterns environmental condition temperature and the battery brand s Dimensions Approx
29. your TV e Fluorescent lamps can interfere with your remote control try turning off the fluorescent lamps e If you are having problems with the remote control reinsert or replace your batteries and make sure that they are correctly inserted Programming the Remote Control Your remote control can be programmed to use other equipment and is pre programmed to operate the following Sony equipment Function Button Sony Equipment Code Number DVD DVD Player 31033 AMP Receiver 52172 STB Digital Satellite 01639 Programming Other Equipment Follow the steps below to program your TV remote control 1 Look for the code in the Manufacturer s Code List refer to i Manual that corresponds to the equipment you would like to operate with the Sony remote control If more than one code is provided try programming the first code listed If your equipment s code is not listed visit http esupport sony com remotecodes for a more comprehensive list 2 Press and hold a DVD AMP or STB function button simultaneously with INPUT button and release When in the programming mode the function button DVD AMP STB blinks for approximately 30 seconds until a code is entered 3 Enter the five digit code using 0 9 while the function buttons DVD AMP STB are lit If the code is not entered within 30 seconds you must repeat step 2 4 Press or ENT to confirm the code If successfully p
Download Pdf Manuals
Related Search