Sony AIR-SA15R Speaker System User Manual
Contents
1. 1 Make sure the power cord is correctly and firmly connected 2 Find your problem in the checklist below and take the indicated corrective action If the issue persists contact your nearest Sony dealer When bringing this unit in for repairs be sure to bring in the entire system this unit the S AIR main unit and wireless transceivers This product is a system product and the entire system is needed to determine the location requiring repair If the STANDBY indicator flashes Immediately unplug the power cord and check if anything is blocking the ventilation holes on the rear panel of the unit After the STANDBY indicator 2 stops flashing reconnect the power cord and turn on the unit If the issue persists contact your nearest Sony dealer The remote does not function Remove any obstacles between the remote and the remote sensor 11 on the unit and position the unit away from fluorescent lights Point the remote at the remote sensor 11 on the unit Move the remote closer to the unit The remote control function is off Turn on the remote control function The S AIR indicator 10 is turned off Check that the power cord is connected securely and the unit is turned on Check that the supplied wireless transceiver is inserted securely to the unit Connecting the unit and S AIR main unit is not possible The S A2. a The clock settings are lost when you disconnect the power cord or if a power failure occurs Listening to the sound of the connected S AIR main unit You can use the S AIR function to listen to the sound of an S AIR main unit in a remote location 1 Perform the procedure described in Establishing the connection with an S AIR main unit and check that the S AIR indicator 10 is lit 2 Press S AIR CH 3 repeatedly to select the desired S AIR channel of the S AIR main unit If PL v Wireless strength IMIE VL I The S AIR channels that can be selected depend on the S AIR main unit For details refer to the Operating Instructions supplied with the S AIR main unit 3 Press VOLUME 9 to adjust the volume To operate the S AIR main unit from the unit You can perform the following operations using the buttons on the remote or unit To Press Start playback of a CD DVD B 4 etc Stop playback ofa CD DVD W CANCEL 4 etc Pause playback ofa CD DVD M 4 etc Select a track file or chapter laa PI 5 of a CD DVD etc Select a preset station when PRESET 5 listening to the radio Change the FM AM band Hold down S AIR when listening to the radio CH 3 until the band changes Dependin
3. Pb This symbol on the battery or on the packaging indicates that the battery provided with this product shall not be treated as household waste On certain batteries this symbol might be used in combination with a chemical symbol The chemical symbols for mercury Hg or lead Pb are added if the battery contains more than 0 0005 mercury or 0 004 lead By ensuring these batteries are disposed of correctly you will help prevent potentially negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of the battery The recycling of the materials will help to conserve natural resources In case of products that for safety performance or data integrity reasons require a permanent connection with an incorporated battery this battery should be replaced by qualified service staff only To ensure that the battery will be treated properly hand over the product at end of life to the applicable collection point for the recycling of electrical and electronic equipment For all other batteries please view the section on how to remove the battery from the product safely Hand the battery over to the applicable collection point for the recycling of waste batteries For more detailed information about recycling of this product or battery please contact your local Civic Office your household waste disposal service or the shop where you purchased the product e S AIR and its
4. Directives The manufacturer of this product is Sony Corporation 1 7 1 Konan Minato ku Tokyo 108 0075 Japan The Authorized Representative for EMC and product safety is Sony Deutschland GmbH Hedelfinger Strasse 61 70327 Stuttgart Germany For any service or guarantee matters please refer to the addresses given in separate service or guarantee documents Disposal of Old Electrical amp Electronic Equipment Applicable in the European Union and other European MEM countries with separate collection systems This symbol on the product or on its packaging indicates that this product shall not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product The recycling of materials will help to conserve natural resources For more detailed information about recycling of this product please contact your local Civic Office your household waste disposal service or the shop where you purchased the product Applicable accessories Wireless Transceiver EZW RT10 EZW RT10A http www sony net Disposal of waste batteries applicable in the European Union and other European countries with separate collection systems
5. operation It is easy to set the same S AIR ID for the unit and S AIR main unit to establish the connection However if a neighbor has an S AIR main unit with the same S AIR ID as your S AIR main unit you may be able to hear the audio transmitted from your neighbor s S AIR main unit on your system To prevent this you can identify the unit with a specific S AIR main unit by performing the pairing operation Before pairing The connection is established by the S AIR ID example Your system Neighboring system This unit 5 IDA ae oN a oN a oy s g lr a IDA IDA S AIR main unit S AIR main unit After pairing The connection is established between the paired unit and S AIR main unit Your system Neighboring system This unit 6 IDA Ca m ri gt ao N Pairing Vex ai ie F S AIR main unit S AIR main unit 1 Place the S AIR main unit to be paired near this unit 2 Check that the power of the unit and the S AIR main unit to be connected are turned on 3 Check that the S AIR ID of the unit is the same as the S AIR ID of the S AIR main unit 4 Operate the S AIR main unit to turn on the pairing function For details on turning on the pairing function refer to the Operating Instructions supplied with the S AIR main unit 5 Press the PAIRING button on the rear panel of the unit using a pointed obj
6. turn off the TV wait about 15 to 30 minutes and turn it back on If there is no improvement move the unit far away from the TV Cleaning the cabinet Clean the cabinet with a soft dry cloth Do not use any type of abrasive pad scouring powder or solvent such as thinner benzine or alcohol S AIR Sony Audio Interactive Radio frequency Recent times have seen the rapid spread of DVD media Digital Broadcasting and other high quality media To ensure that the subtle nuances of these high quality media are transmitted with no deterioration Sony has developed a technology called S AIR for the radio transmission of digital audio signals with no compression and has incorporated this technology into the EZW RT10 EZW RTI0A This technology transfers digital audio signals with no compression using the 2 4 GHz band range of ISM band Industrial Scientific and Medical band such as wireless LANs and Bluetooth applications Getting Started Connect the unit and S AIR main unit to listen to sound from the S AIR main unit Wall socket EZW RT10 EZW RT10A Wireless transceiver Wireless transceiver Insert the supplied wireless transceiver EZW RT10 or EZW RT10A securely into the EZW RT10 slot on the rear panel of the unit Check the orientation of the V mark when inserting the supplied wireless transceiver EZW RT10 or EZW RT10A Failure to do so may result in damage to the unit Notes Make
7. IR indicator 10 flashes Check that the supplied wireless transceiver is inserted securely to the unit If you use another S AIR main unit place it more than 8 m away from the S AIR main unit you are using Confirm the S AIR IDs of the unit and the S AIR main unit The unit is paired with another S AIR main unit Pair the unit with the S AIR main unit you are using The unit is paired with another S AIR main unit Cancel pairing Place so that the unit and the S AIR main unit are separated from other wireless devices Stop using any other wireless devices The connected S AIR main unit is turned off Make sure the power cord is connected and turn on the S AIR main unit The S AIR channel fails to change Check that the unit and the S AIR main unit are connected properly There is no sound If you use another S AIR main unit place it more than 8 m away from the S AIR main unit you are using Confirm the S AIR IDs of the unit and the S AIR main unit Check the pairing setting e Place so that the unit and the S AIR main unit are closer Stop using any equipment that generates electromagnetic energy such as a microwave oven Place so that the unit and the S AIR main unit are separated from other wireless devices Stop using any other wireless devices Change the S AIR ID settings of the unit and the S AIR main unit Turn off the unit and S AIR main un
8. SONY Wireless 4 117 794 31 1 Speaker System Operating Instructions AIR SA15R ole s S AIR DIGITAL WIRELESS 2009 Sony Corporation Printed in China To reduce the risk of fire or electric shock do not expose this apparatus to rain or moisture To reduce the risk of fire do not cover the ventilation opening of the apparatus with newspapers tablecloths curtains etc Do not place the naked flame sources such as lighted candles on the apparatus To reduce the risk of fire or electric shock do not expose this apparatus to dripping or splashing and do not place objects filled with liquids such as vases on the apparatus As the main plug is used to disconnect the unit from the mains connect the unit to an easily accessible AC outlet Should you notice an abnormality in the unit disconnect the main plug from the AC outlet immediately The unit is not disconnected from the mains as long as it is connected to the AC outlet even if the unit itself has been turned off Do not install the appliance in a confined space such as a bookcase or built in cabinet Do not expose batteries or apparatus with battery installed to excessive heat such as sunshine fire or the like The nameplate is located on the bottom exterior Excessive sound pressure from earphones and headphones can cause hearing loss Notice for customers the following information is only applicable to equipment sold in countries applying EU
9. ect When pairing is performed the S AIR indicator 10 on the unit flashes and the display changes as follows PAIRING COMPLETE To cancel pairing Change the S AIR IDs of the unit and the S AIR main unit to different S AIR IDs To stop the pairing operation midway Press the PAIRING button again Inserting the batteries to the remote Slide and remove the battery compartment lid 12 and insert the two supplied R03 size AAA batteries side first matching the polarities shown below Notes on using the remote With normal use the batteries should last for about six months Do not mix an old battery with a new one or mix different types of batteries If you do not use the remote for a long period of time remove the batteries to avoid damage from battery leakage and corrosion Operations Unit AIR SA15R Wireless Speaker System Setting the clock Use buttons on the unit to set the clock 1 Turn on the unit Press 1 4 2 Select the clock set mode Press CLOCK TIMER MENU 8 If the current mode appears on the display press i lt gt gt repeatedly to select CLOCK and then press CLOCK TIMER ENTER 8 3 Set the time Press k lt PI 5 repeatedly to set the hour and then press CLOCK TIMER ENTER 8 Use the same procedure to set the minute
10. edly to select OFF 4 Press CLOCK TIMER ENTER 8 To change the setting Start over from step 1 Tip The Daily Timer setting remains as long as the setting is not canceled manually Turning off the remote control function In addition to the unit you already have you can connect other S AIR sub units to a single S AIR main unit and use them together However when using multiple S AIR sub units near each other all the S AIR sub units may receive the same signal from the remote and the connected S AIR main unit may not function properly To prevent this you can turn off the remote control function of the S AIR sub units Use buttons on the S AIR sub unit whose remote control function you want to turn off 1 Press 1 1 to turn off the unit 2 Press DISPLAY 6 repeatedly until the clock is displayed 3 Press 1 T while holding down CLOCK TIMER ENTER 8 RMT OFF appears in the display and the unit is turned on If you try controlling the unit using the remote RMT OFF appears in the display and the unit will not accept the signal from the remote To turn on the remote control function Perform steps 1 and 3 above and check that RMT ON appears in the display Note Even when the remote control function is turned off 1 and VOLUME 9 on the remote will continue to function pen
11. g on the connected S AIR main unit the operation may differ Refer to the Operating Instructions of the S AIR main unit To listen with headphones Connect headphones not supplied to the Q headphones jack located on the rear panel of the unit Note The elapsed playing time or remaining playing time of the CD DVD etc being played on the S AIR main unit may not 7 gt be displayed on this unit In this case appears 10 Changing the display To change the information on the display while the unit is on Press DISPLAY 6 on the unit Each time you press the button the display changes as follows When the unit is connected to an S AIR main unit Information of the connected S AIR main unit gt Model name of the connected S AIR main unit gt Clock When the unit is not connected to an S AIR main unit S AIR UNLINKED Clock D The displayed information depends on the connected S AIR main unit Up to 16 characters can be displayed Displayed for about 8 seconds To turn off the display When the unit is turned off the clock is displayed You can turn off the clock display to minimize the amount of power consumed Power Saving Mode Press DISPLAY 6 on the unit when the clock is displayed Press the button again to display the clock Note The STANDBY indicator 2 on the unit lights up when the unit
12. in printed wiring boards
13. is off Using the Timers The unit offers two timer functions If you use the Daily Timer with the Sleep Timer the Sleep Timer has priority Use buttons on the unit to set the timers Sleep Timer You can fall asleep to music This function works even if the clock is not set Press SLEEP 7 repeatedly Note Even if you set the timer no sound is output from the unit if playback on the connected S AIR main unit ends within the set time period or if communication with the S AIR main unit is cut off Daily Timer You can wake up to the sound of the connected S AIR main unit at a preset time Make sure you have set the clock 1 Press VOLUME 9 repeatedly to adjust the volume level while viewing the volume level indication on the display 2 Press CLOCK TIMER MENU 8 Press k PP1 5 repeatedly to select TIMER then press CLOCK TIMER ENTER 8 ON TIME appears and the hour indication flashes 4 Set the time to start playing Press k lt P I 5 repeatedly to set the hour and then press CLOCK TIMER ENTER 8 The minute indication flashes Use the procedure above to set the minute 5 Use the same procedure as in step 4 to set the time to stop playing Remote RM ANU046 6 Press lt 4 PPI 5 repeatedly to select the desired option The default setting is underli
14. it and then turn them on again Check that the power cord is connected securely and the unit is turned on Increase the volume of the unit Check that headphones are not connected to the Q headphones jack on the rear panel of the unit There is noise or the sound skips If you use another S AIR main unit place it more than 8 m away from the S AIR main unit you are using Place so that the unit and the S AIR main unit are closer Stop using any equipment that generates electromagnetic energy such as a microwave oven Place so that the unit and the S AIR main unit are separated from other wireless devices Stop using any other wireless devices Change the S AIR ID settings of the unit and the S AIR main unit Do not place a mobile phone near the unit and the S AIR main unit as this may result in noise To reset the unit to factory settings If the unit still does not operate properly reset the unit to factory settings 1 Disconnect and reconnect the power cord and then turn on the unit 2 Press CANCEL 4 DISPLAY 6 and 1 1 on the unit at the same time All user configured settings such as timer clock etc are deleted CANCEL Time out without pairing COMPLETE Pairing is completed ID A Sets the S AIR ID to A ID B Sets the S AIR ID to B ID C Sets the S AIR ID to C LINKED The unit is connected to the S AIR mai
15. logo are trademarks of Sony Corporation The Bluetooth word mark and logos are owned by the Bluetooth SIG Inc and any use of such marks by Sony Corporation is under license Other trademarks and trade names are those of their respective owners The AIR SA15R is an S AIR compatible product It is also called the S AIR sub unit Connecting this unit with an S AIR main unit using S AIR technology you can use each unit in a remote location For example you can install this unit in the bedroom and then install an S AIR main unit in the living room You can then listen to the music from the S AIR main unit located in the living room by controlling this unit Notes on use of the S AIR product As the S AIR product transmits sound by radio waves sound may skip when radio waves are obstructed This is a characteristic of radio waves and is not a malfunction As the S AIR product transmits sound by radio waves equipment that generates electromagnetic energy such as a microwave oven may interfere with sound transmission As the S AIR product uses the radio waves that share the same frequency as other wireless systems such as wireless LAN or Bluetooth devices interference or poor transmission may result In this case take the following steps Do not install the S AIR product near other wireless systems Do not use the S AIR product and the other wireless systems at the same time The transmissio
16. n distance differs depending on the usage environment Find a location where transmission between the unit and the S AIR main unit is most effective and install the unit and the S AIR main unit there On safety Completely disconnect the power cord from the wall socket mains if it is not going to be used for an extended period of time When unplugging the unit always grip the plug Never pull the cord itself Should any solid object or liquid get into the unit unplug the unit and have it checked by qualified personnel before operating it again The power cord can be changed only by a qualified service facility On placement Do not place the unit in an inclined position or in locations that are extremely hot cold dusty dirty or humid or lacking adequate ventilation or subject to vibration direct sunlight or a bright light Be careful when placing the unit on surfaces that have been specially treated for example with wax oil polish as staining or discoloration of the surface may result On heat buildup Heat buildup on the unit during operation is normal and is not cause for alarm Do not touch the cabinet if it has been used continuously at a high volume because the cabinet may have become hot Do not obstruct the ventilation holes On the speaker system This speaker system is not magnetically shielded and the picture on nearby TV sets may become magnetically distorted In this situation
17. n unit PAIRING Pairing is in progress RMT OFF The unit is not accepting signals from the remote because the remote control function is set to RMT OFF S AIR Displayed from the point power of the unit is turned on until connection with the S AIR main unit is established TIME NG The Daily Timer start and end times are set to the same time UNLINKED The connection with the S AIR main unit is cut off Amplifier section DIN power output rated 3 3 watts 3 ohms at 1 kHz DIN Continuous RMS power output reference 4 4 watts 3 ohms at 1 kHz 10 THD Output Q stereo mini jack Accepts headphones with an impedance of 8 ohms or more Speaker section Speaker system Full range bass reflex type Speaker units 65 mm cone type 2 Nominal impedance 3 ohms Wireless transceiver EZW RT10 EZW RT10A Communication System S AIR Specification version 1 0 Frequency band 2 4000 GHz 2 4835 GHz Modulation method DSSS Power requirements DC 3 3 V 350 mA Dimensions w h d 50 x 13 x 60 mm Mass 24 g General Power requirements 230 V AC 50 60 Hz Power consumption 15 watts Dimensions w h d Approx 300 x 136 x 115 mm Mass Approx 2 2 kg Supplied accessories Wireless transceiver EZW RT10 or EZW RT10A 1 Remote commander RM ANU046 1 R03 size AAA batteries 2 Design and specifications are subject to change without notice Halogenated flame retardants are not used in the certa
18. ned ALARM An alarm is output AUTO Sound from the connected S AIR main unit is output However an alarm sounds in the following cases When communication with the S AIR main unit is cut off When no sound is output from the S AIR main unit or the audio signal level is too low When the S AIR main unit is not ready for playback at the set start time Note that the alarm continues to sound even if the S AIR main unit becomes ready after the start time has passed 7 Press CLOCK TIMER ENTER 8 The display shows the timer settings 8 If you selected ALARM in step 6 go to step 9 If you selected AUTO in step 6 prepare the sound source on the S AIR main unit For details on preparing the sound source refer to the Operating Instructions supplied with the S AIR main unit 9 Press 1 T to turn off the unit The unit turns on about 45 seconds before the preset time If the unit is on at the preset time the Daily Timer will not play To stop the alarm Press any button To activate or check the timer again 1 Press CLOCK TIMER MENU 8 SELECT flashes in the display 2 Press CLOCK TIMER ENTER 8 3 Press kE P I 5 repeatedly to select TIMER 4 Press CLOCK TIMER ENTER 8 To cancel the timer 1 Press CLOCK TIMER MENU 8 SELECT flashes in the display 2 Press CLOCK TIMER ENTER 8 3 Press kE PP I 5 repeat
19. sure to turn off the unit when inserting or removing the supplied wireless transceiver EZW RT10 or EZW RT10A Failure to do so may result in damage to the unit Do not touch the terminals of the supplied wireless transceiver EZW RT10 or EZW RT10A Do not insert any device other than the supplied wireless transceiver EZW RT10 or EZW RT10A into the EZW RT10 slot Ej S AIR ID selector Set the same S AIR ID for this unit and the S AIR main unit to be connected For details on setting the S AIR ID see Establishing the connection with an S AIR main unit Power Connect the power cord to a wall socket Establishing the connection with an S AIR main unit You can easily establish the connection by setting the same S AIR ID for this unit and S AIR main unit 1 Turn on the unit Press 1 1 2 Set the S AIR ID of the unit to the same S AIR ID as the S AIR main unit to be connected For details on setting the S AIR ID of the S AIR main unit refer to the Operating Instructions supplied with the S AIR main unit 3 Operate the S AIR main unit to turn on the S AIR function For details on turning on the S AIR function refer to the Operating Instructions supplied with the S AIR main unit Once the connection is established the S AIR indicator 10 on the unit lights up and LINKED appears in the display for about 2 seconds Identifying the unit with a specific S AIR main unit Pairing
Download Pdf Manuals
Related Search