SonicWALL TZ 170 Riding Toy User Manual
Contents
1. address computers on the Internet e Subnet Mask A set of numbers in IP address format using 255 in place of the XXX s It determines the type of network by masking out numbers A Class C network has a subnet mask of 255 255 255 0 e Default Gateway A device on an internetwork that forwards packets to another network e DNS Domain Name System Server A computer that looks up the name of a computer and finds the corresponding IP address This allows you to access computers on the Internet without configuring IP addresses for remote connections e PPPoE Point to Point Protocol over Ethernet supports the transmission of network packets over serial transmis sion lines such as DSL or POTS Plain Old Telephone Service e DHCP Dynamic Host Configuration Protocol allocates IP addresses to computers on the network automatically without assigning a computer a static fixed IP address e VPN Virtual Private Network is a virtual network that encrypts data and sends it privately over the Public Internet Setup Continues Page 2 Setting Up Your SonicWALL Applying Power to the SonicWALL Attach the power supply to the power cord Plug the power adapter into the SonicWALL and plug the other end into a power outlet The Power light turns green when power is applied to the SonicWALL Also the Test light remains lit for approximately 90 seconds while the SonicWALL performs a series of diagnostic tests Connecting the2. detected as your network connection enter your user name and password from your ISP Click Next If a DHCP server is detected click Next Step 6 LAN Settings Review the LAN IP address and subnet mask Use the default values Step 11 SonicWALL Configuration Summary Write down your network configuration information below Click Apply Setup Wizard Complete Your SonicWALL is now successfully configured for LAN and Internet access Click Restart to complete the configuration process Network Settings WAN Network Mode ss _ IP Address Subnet Mask Router IP Address ss DNS Server 1 IP Address _ DNS Server 2 IP Address _ _ LAN IP Address Subnet Mask DHCP Enabled Yes__ No __ You must register your SonicWALL at lt htto www mysonicwall com gt to obtain the latest version of SonicWALL SonicOS 2 0s firmware and access technical support Setup Continues Configuring Computers on the LAN When the SonicWALL restarts a window displays information to configure computers on your LAN DHCP Server Enabled on the SonicWALL TZ 170 If you enabled the SonicWALL DHCP Server or have a DHCP Server on your LAN each computer must be configured to obtain its IP address dynamically After the SonicWALL has restarted change the network settings on the computers on the LAN Follow the steps below for your operating system Windows XP NO of WD Click Start then Connec
3. gt COMPREHENSIVE INTERNET SECURITY SonicWALL Internet Security Appliances TZ 170 Quick Start Guide SONICWALL gt Quick Start Installation Thank you for purchasing a SonicWALL Internet security appliance The SonicWALL acts as a secure barrier between your private LAN and the public Internet WAN to protect your networks from security threats on the Internet This Quick Start Guide provides instructions for installing and configuring your SonicWALL TZ 170 as an Office Gateway on your network After you complete this guide you can access the Internet securely through your LAN connection Before You Begin Check Package Contents e One SonicWALL Internet Security Appliance e One SonicWALL Quick Start Guide e One SonicWALL Firmware and Documentation CD e One Ethernet cable e One RJ45 CLI cable e One 5 Volt DC power supply e One Power cord The RJ45 CLI cable is only included with the purchase of a TZ 170 with SonicOS Enhanced A power cord is included only with units shipped to North America If any items are missing from your package contact SonicWALL Inc Web lt http www sonicwall com support gt Phone 888 777 1476 Overview of the SonicWALL TZ 170 Hardware SONICWALL TZ 170 Test Light Power Light opt Link 100 Activity LAN Link 100 Activity Link Activity Console Port WAN Port Optional Port LAN Ports 1 5 Power SonicWALL TZ 170 Quick Start Guide Page 1 What You Need to Get Co
4. 09 03 gt SONICWALL gt
5. SonicWALL to the Network Connect one end of an Ethernet cable to your DSL modem cable modem or Internet router Connect the other end of the Ethernet cable to the WAN port of the SonicWALL The link LED lights indicating an active connection E Connect one end of an Ethernet cable to the Ethernet port of your computer Connect the other end of the cable to LAN 1 port of your SonicWALL The link LED lights indicating an active connection Setup Continues SonicWALL TZ 170 Quick Start Guide Page 3 O Configuring Your Management Station Your SonicWALL is configured with the default IP address of 192 168 168 168 This IP address is used to initially access the Management interface of the SonicWALL and launch the Setup Wizard To access the Management interface for the first time you must configure your computer with an IP address in the same network range as the SonicWALL Follow the instructions below for your operating system Windows XP Click Start then Connect to Right click on the Local Area Connection icon and select Properties Open the Local Area Connection Properties window Double click Internet Protocol TCP IP to open the Internet Protocol TCP IP Properties window Select Use the following IP address and type 192 168 168 200 in the IP address field Type 255 255 255 0 in the Subnet Mask field Type the DNS IP address in the Preferred DNS Server field If you have more than one addre
6. ct on the computer Windows 2000 COND OF WNDY 1 From your Windows task bar click Start 2 Then click Settings 3 Click Network and Dial up Connections 4 Double click the network icon to open the connection window 5 Click Properties 6 Highlight Internet Protocol TCP IP and click Properties 7 Select Use the following IP address 8 Type an IP address from your LAN IP range IP address field 9 Enter 255 255 255 0 in the Subnet field 10 Type the SonicWALL LAN IP Address into the Default Gateway field 11 If you have a DNS Server IP address from your ISP enter it in the Preferred DNS Server field Page 8 Windows NT OOoOnN OOF WN From the Start list highlight Settings and then select Control Panel Double click the Network icon in the Control Panel window Double click TCP IP in the TCP IP Properties window Select Specify an IP Address Type an IP address from your LAN IP range in the IP Address field Type 255 255 255 0 in the Subnet Mask field Type the SonicWALL LAN IP Address in the Default Gateway field Click DNS at the top of the window Type the DNS IP address in the Preferred DNS Server field If you have more than one address enter the second one in the Alternate DNS server field 10 Click OK and then click OK again 11 Restart the computer Windows 98 1 OND oO FW PY 9 From the Start list highlight Settings and then select Control Panel Double c
7. ight remains on If the Test light remains on after 90 seconds the firmware may be corrupted Follow these steps to load firmware onto the appliance To load new firmware onto the SonicWALL TZ 170 power down the appliance Wait 30 seconds press and hold the Reset button At the same time power on the appliance Continue to hold the Reset button until the Test light begins blinking Once the Test light stops blinking and remains lit release the Reset button Open a Web browser and type 192 168 168 168 into the Address or Location field A Web page displays the message Firmware appears to be corrupted Click Browse to open a File Open dialogue box Browse to the location of the firmware file A rescue version of the firmware is located on the product CD 8 After restoring the firmware on the appliance go to lt https www mysonicwall com gt and log into your account Download the latest version of the firmware and then upload it to your appliance NO OF BWDP SonicWALL TZ 170 Quick Start Guide Page 11 SonicWALL Inc 1143 Borregas Avenue T 408 745 9600 www sonicwall com Sunnyvale CA 94089 1306 F 408 745 9300 2002 SonicWALL Inc SonicWALL is a registered trademark of SonicWALL Inc Other product and company names mentioned herein may be trademarks and or registered trademarks of their respective companies Specifications and descriptions subject to change with out notice P N232 000398 00 RevA
8. indow Double click TCP IP in the TCP IP Properties window Select Specify an IP Address Type 192 168 168 200 in the IP Address field Type 255 255 255 0 in the Subnet Mask field Click DNS Configuration Type the DNS IP address in the Preferred DNS Server field If you have more than one address type the second one in the Alternate DNS server field Click OK and then click OK again Restart the computer for changes to take effect Launching the Setup Wizard To begin the configuration of your SonicWALL you must log into the SonicWALL using a Web browser and the default LAN IP address 192 168 168 168 of the SonicWALL Follow the instructions below 1 Launch your Web browser Because you are temporarily disconnected from the Internet you may receive an error message when your eet Web browser first opens This does not affect your installation process Continue with the steps below ert 2 Enter 192 168 168 168 in the Location or Address field A Intern et a Your Web browser must support Java and HTTP uploads in order to fully manage the SonicWALL appliance nea Internet Explorer 5 0 or higher as well as Netscape Navigator 4 0 or higher are recommended ert 3 The SonicWALL Installation Wizard launches and guides you through the configuration and setup of your SonicWALL Setup Continues gt SonicWALL TZ 170 Quick Start Guide Page 5 If you cannot co
9. lick the Network icon in the Control Panel window Double click TCP IP in the TCP IP Properties window Select Specify an IP Address Type an IP address from your LAN IP range in the IP Address field Type 255 255 255 0 in the Subnet Mask field Type the SonicWALL LAN IP Address in the Default Gateway field Click DNS Configuration Type the DNS IP address in the Preferred DNS Server field If you have more than one address type the second one in the Alternate DNS server field Click OK and then click OK again 10 Restart the computer for changes to take effect LAN Configuration Complete The SonicWALL is now functioning and protecting your network from Internet based attacks and break ins SonicWALL TZ 170 Quick Start Guide Page 9 SONICWALL TZ 170 Technical Specifications Processor SonicWALL Security Processor RAM 64 MB Flash Memory 8 MB Interfaces 7 10 100 auto sensing Ethernet 1 WAN 10 100 Base T 1 Optional Port 1 5 port Auto MDIX Switch 1 RJ45 Console Port Firewall Performance 90 Mbps Site to Site VPN Policies 10 Node 1 25 Node 10 Unrestricted Nodes 10 Bundled VPN Client Sessions 10 Node O 25 Node 1 Unrestricted Nodes 1 Firewall Nodes 10 25 Unrestricted Concurrent Connections 6 000 VPN Performance 25 Mbps 83DES and AES Page 10 Dimensions 9 07 x 6 63 x 1 63 inches 23 03 x 16 84 x 4 14 cm Weight 1 15 Ib 0 52 kg LEDs Status Po
10. nel window 2 Double click TCP IP in the TCP IP Properties window 3 Select Obtain IP Address automatically 4 Click DNS Configuration 5 Select Obtain DNS Server automatically 6 Click OK and then click OK again 7 Restart the computer for changes to take effect LAN Configuration Complete The SonicWALL is now functioning and protecting your network from Internet based attacks and break ins DHCP Server Disabled If you did not enable the SonicWALL DHCP server or you do not have a DHCP server on your network you must configure each computer with a static IP address from your LAN IP address range After the SonicWALL has restarted change the nework settings on computers located on the LAN Follow the steps below to configure computers on your LAN Windows XP Click Start then Connect to Right click on the Local Area Connection icon and select Properties Open the Local Area Connection Properties window Double click Internet Protocol TCP IP to open the Internet Protocol TCP IP Properties window Select Use the following IP address and type an IP address from your LAN IP range in the IP address field Type 255 255 255 0 in the Subnet Mask field Type the SonicWALL LAN IP Address into the Default Gateway field Type the DNS IP address in the Preferred DNS Server field If you have more than one address type the second one in the Alternate DNS server field 9 Click OK for the settings to take effe
11. nnect to the SonicWALL TZ 170 check the following e Did you correctly enter the SonicWALL TZ 170 LAN IP address in your browser window e Is the SonicWALL TZ 170 connected to the same network as your computer e Have you changed the TCP IP network settings on your computer Step 4 suis TIP a PRN TIP Page 6 The Setup Wizard The Setup Wizard provides easy to follow instructions for configuring the SonicWALL on your network You must have your ISP information to complete the configuration using the Setup Wizard Certain browser configurations may not launch the Installation Wizard automatically In this case you must log into the SonicWALL using Admin as the User Name and password as the Password After you log into the SonicWALL click Wizards Select Setup to begin configuring the SonicWALL Follow the steps below for the quickest and easiest configuration for the TZ 170 as an Office Gateway Step 1 Welcome Read the information on the Welcome dialogue box Click Next Step 2 Change Password change the TZ 170 password to your personal password Click Next Step 3 Change Time Zone change the Time Zone to your location s Time Zone Click Next Step 4 WAN Network Mode the type of network connectivity is detected automatically If you want to select a different network mode consult the SonicOS 2 0s Administrators Guide on your product CD for more information Step 5 WAN Network Mode if PPPoE is
12. nnected e SonicWALL Internet Security Appliance e Internet Connection e PC or Macintosh computer e A Web browser Microsoft Internet Explorer v5 0 or later or Netscape Navigator v4 7 or later your Web browser must support Java and HTTP uploads in order to fully manage the SonicWALL e Internet Service Provider ISP Information TEL ISP Connection Information Before you can begin installing your SonicWALL determine how your ISP distributes IP addresses Call your ISP to find out if your Internet connection uses DHCP to obtain an IP address or PPPoE typical of DSL access or if they have given you a static IP address Record all of your networking information in the checklist below IP Addressing using DHCP No action necessary The SonicWALL automatically detects the presence of a DHCP server during setup IP Addressing using PPPoE UserName Password IP Addressing using a Single Static Public IP Address IP Address Default Gateway Primary DNS __ a E Secondary DNS _ A If you are not using one of the network configurations above step by step installation instructions for additional networking methods are found in Configuring the Network Mode section of your Administrator s Alert Guide The Administrator s Guide is located on your product CD and requires Acrobat Reader to view it Acrobat Reader is also provided on your product CD Glossary IP Address A set of numbers in the format XXX XXX XXX XXX used to
13. ss type the second one in the Alternate DNS server field 8 Click OK for the settings to take effect on the computer Windows 2000 NO Ff WD 1 From your Windows task bar click Start 2 Then click Settings 3 Click Network and Dial up Connections 4 Double click the network icon to open the connection window 5 Click Properties 6 Highlight Internet Protocol TCP IP and click Properties 7 Select Use the following IP address 8 Enter 192 168 168 200 in the IP address field 9 Enter 255 255 255 0 in the Subnet field 10 If you have a DNS Server IP address from your ISP enter it in the Preferred DNS Server field Windows NT From the Start list highlight Settings and then select Control Panel Double click the Network icon in the Control Panel window Double click TCP IP in the TCP IP Properties window Select Specify an IP Address Type 192 168 168 200 in the IP Address field Type 255 255 255 0 in the Subnet Mask field Click DNS at the top of the window Type the DNS IP address in the Preferred DNS Server field If you have more than one address enter the second one in the Alternate DNS server field 9 Click OK and then click OK again 10 Restart the computer ONDOoB WN Setup Continues Page 4 Windows 98 1 N OF W DY 00 From the Start list highlight Settings and then select Control Panel Double click the Network icon in the Control Panel w
14. t to Right click on the Local Area Connection icon and select Properties Open the Local Area Connection Properties window Double click Internet Protocol TCP IP to open the Internet Protocol TCP IP Properties window Select Obtain an IP address automatically Select Obtain DNS Server automatically Click OK and then OK again for the settings to take effect on the computer Windows 2000 1 From your Windows task bar click Start 2 Then click Settings 3 Click Network and Dial up Connections 4 Double click the network icon to open the connection window 5 6 7 8 9 Click Properties Highlight Internet Protocol TCP IP and click Properties Select Obtain an IP address automatically Select Obtain DNS Server automatically Click OK and then OK again for the settings to take effect on the computer Windows NT CONDOR WNDY From the Start list highlight Settings and then select Control Panel Double click the Network icon in the Control Panel window Double click TCP IP in the TCP IP Properties window Select Obtain an IP address automatically Click DNS at the top of the window Select Obtain DNS Server automatically Click OK and then click OK again Restart the computer Setup Continues SonicWALL TZ 170 Quick Start Guide Page 7 Windows 98 1 From the Start list highlight Settings and then select Control Panel Double click the Network icon in the Control Pa
15. wer Test LAN 1 per port multifunctional WAN link activity 100 Optional Port link activity 100 Input Power 100V to 240VAC Power Consumption 12 Watts Maximum Standards NAT DNS RIPv1 v2 TCP IP UDP ICMP HTTP HTTPS IPSec ISAKMP IKE SNMP DHCP PPPoE L2TP PPTP RADIUS Environment Temperatures 40 105 F 5 40 C Relative Humidity 10 90 noncondensing Operational Altitude 0 to 13 123 ft 4000m Operating System SonicOS Standard upgradeable to SonicOS Enhanced Major Regulatory Compliance EMC FCC Class B ICES Class B CE C tick VCCI BSMI MIC Safety UL cUL TUV GS CB NOM Appendix Resetting the Firmware to Factory Default Settings At times it may be necessary to reset the firmware on your SonicWALL TZ 170 For example if you ve forgotten your password and cannot access the management interface resetting the firmware allows you to reset the SonicWALL TZ 170 to factory default settings including the user name and password To quickly reset the firmware to factory default settings locate the Reset button on the back of the SonicWALL TZ 170 next to the LAN connection Using a pointed object press and hold the Reset button for 5 10 seconds All settings are returned to the factory default settings including the password and the default LAN IP address of 192 168 168 168 Note This reset method does not require reloading the firmware Resetting Firmware if Firmware is Corrupted Test L
Download Pdf Manuals
Related Search