Home

Snapper 5900750 Lawn Mower User Manual

1. 2 Safety Rules and Information 2 Safety Decal Suisiana cave 11 Safety Interlock System 12 Safety Alert Symbol amp Signal Words 12 Safety ICONS iii iii 13 Features 8 Controls 13 Identification Numbers 13 Control FUNCIONS rissies eaa 14 Operations ds 16 General inicia cient 16 Checks Before Starting 16 Checking Tire Pressures 17 Seat Adjustment 17 Mowing Height Adjustment 17 Foot Pedal Adjustment 18 Raise and Lower the Roll Bar 18 Starting the Engine 19 Stopping the Rider su a aa aaqannaunaqnasss 19 Pushing the Rider by Hand 19 Zero Turn Driving Practice 20 WO WING uscar 22 Mowing Reccomendations 22 Mowing Methods 28 Attaching a Traila ensisi 24 Regular Maintenancoes 25 Maintenance Schedule
2. 25 Checking Adding Fuel 26 Fuel Fill er u u usss daska asua atin 26 Oil 8 Filter Change orisni 26 LubricCati0N E E E E S norris 27 Check Hydraulic Oil Level 28 Hydraulic Oil Filter Change 28 Servicing the Mower Blades 29 Ground Speed Control Lever Adjustment 31 Speed Balancing Adjustment 31 Neutral Adjustment 32 Parking Brake Adjustment 32 Deck Rod Timing Adjustment 61 Models 33 Deck Leveling Adjustment 61 Models 34 Deck Rod Timing Adjustment 72 Models 35 Deck Leveling Adjustment 72 Models 36 Mower Belt Replacement 37 Deck Lift Assist Springers eana 38 Hydraulic Pump Drive Belt Replacement 39 Battery Maintenan N 40 Battery Service 41 O Me A asas Linea 43 Starting After Long Term Storage 43 Troubleshooting 44 Troubleshooting the Rider 44 Troubleshooting the Mower 45 Troubleshooting Common Cutting Problem
3. Cut tall grass at maximum cutting height during first pass Cut grass with discharge pointing toward previously cut area Tighten to 70 ft lbs 94 N m Check and replace as necessary k Remove sharpen and balance blades See Maintenance Section Reinstall Correctly Repair or replace Replace with correct belt Repair or replace as needed Replace drive belt Locate amp repair damaged wire See PTO Clutch Adjustment section Recharge battery and check alternator See Battery Maintenance section 45 Troubleshooting Troubleshooting Common Cutting Problems PROBLEM CAUSE REMEDY Streaking 1 Blades are not sharp x a your A 2 Blades are worn down too far 3 x ace your a rata 3 Engine speed is too slow i iie mowa TOLG 4 Ground speed is too fast 5 ate ee OHA RAR 5 Deck is plugged with grass 6 0 E a 6 Not overlapping cutting rows enough 7 ve ap you cung ni dit 7 Not overlapping enough when turning en turning your effective cutting widt decreases overlap more when turning or wre Lawn is uneven or bumpy Mower deck cutting height is set too low Ground speed is too fast Deck is not levelled correctly Tire pressure is low or uneven ork OON Roll or level the lawn Raise the cutting height Slow down Correctly level the deck Check and inflate the tires O Ot wonr Deck is not leveled c
4. The time of day and condition of the grass greatly affect the results you ll get when mowing For the best results follow these guidelines 1 Mow when the grass is between three and five inches high 2 Mow with sharp blades Short clippings of grass one inch or shorter decompose more quickly than longer blades Sharp mower blades cut grass cleanly and efficiently preventing frayed edges which harm the grass 3 Mow at time of day when the grass is cool and dry Late afternoon or early evening often provide these ideal mowing conditions 4 Avoid mowing after rain or even heavy dew and never mulch when the grass is wet moist grass does not mulch well and clumps beneath the mower deck Mowing Patterns Always start mowing on a smooth level area The size and type of area to be mowed will determine the best mowing pattern to use Obstructions such as trees fences and buildings and conditions such as slopes and grades must also be considered 1 Cut long straight strips overlapping slightly 2 Where possible change patterns occasionally to eliminate matting graining or a corrugated appearance 3 For a truly professional cut mow across the lawn in one direction then recut the lawn by mowing perpendicular to the previous cut Note Always operate the engine at full throttle when mowing If you hear the engine slowing down you are mowing too fast using a slower ground speed will improve the cutting effici
5. Inspecting the Mower Blades k DANGER Avoid injury A worn or damaged blade can break and a piece of the mower blade could be thrown into the operator s or bystander s area resulting in serious personal injury or death e Inspect the mower blade every 25 hours or at least once a year e If the mower blade hits a solid object stop the engine immediately and inspect the mower blade e Never weld or straighten bent mower blades Remove the mower blade from the unit See Removing the Blade Inspect the mower blade Figures 27 amp 28 Discard the mower blade if it has any of the below conditions A Has more than 5 12 7 mm of the mower blade metal removed from previous sharpening or wear D Figure 28 B The air lifts are excessively eroded B amp C Figure 28 and the notch C is 25 6 35 mm deep or greater C Mower blade is bent or broken If the cutting edges are not sharp or have nicks sharpen the blades See Sharpening the Mower Blades Regular Maintenance Figure 27 inspecting the Mower Blade Tips A Mower Blade Cutting Edge B Square Corner C Air Lift D Wear Measurement DISCARD Mower Blade If greater than 5 12 7 mm ZAS Figure 28 inspecting the Mower Blade Air Lifts A B Mower Blade at Wear Limit A notch begins to form C New Mower Blade Mower Blade in Dangerous Con
6. NOTE Gasoline if permitted to stand unused for extended periods 30 days or more may develop gummy deposits which can adversely affect the engine carburetor and cause engine malfunction To avoid this condition add a gasoline Stabilizer to the fuel tank and run the engine a few minutes or drain all fuel from the unit before placing it in storage Starting After Long Term Storage Before starting the unit after it has been stored for a long period of time perform the following steps 1 Remove any blocks from under the unit 2 Install the battery if it was removed 3 Unplug the exhaust outlet and air cleaner 4 Fill the fuel tank with fresh gasoline See engine manual for recommendations 5 See engine owner s manual and follow all instructions for preparing engine after storage 6 Check crankcase oil level and add proper oil if necessary If any condensation has developed during storage drain crankcase oil and refill 7 Inflate tires to proper pressure Check fluid levels 8 Start the engine and let it run slowly DO NOT run at high speed immediately after starting Be sure to run engine only outdoors or in well ventilated area 43 Troubleshootiny Troubleshooting Troubleshooting Chart While normal care and regular maintenance will extend the life of your equipment prolonged or constant use may eventually require that service be performed to allow it to continue operating properly The troubleshoo
7. Remove hoses from filter Install new filter in proper flow direction in fuel line Secure with hose clamps Reconnect the negative battery cable when finished Change Oil amp Filter 1 Warm engine by running for a few minutes Refer to the engine operator s manual for oil amp filter replacement instructions 2 Place the oil drain hose A Figure 19 down through the hole D in the engine deck 3 Place a small pan under the oil drain hose to catch the oil Using the appropriate tools remove the cap B from the drain hose and drain the engine oil into the pan 4 Replace the cap and wipe up any spilled oil 5 Place an absorbent shop cloth under the engine oil filter Remove the engine oil filter and replace with a new one 6 Remove the shop cloth and wipe up any spilled oil NOOO W PP Engine Maintenance Refer to engine owner s manual for all engine maintenance procedures and recommendations Inspect Muffler and Spark Arrester Inspect the muffler for cracks corrosion or other damage Remove the spark arrester if equipped and inspect for damage or carbon blockage If replacement parts are required make sure to use only original equipment replacement parts 26 A WARNING Gasoline is highly flammable and must be handled with care Never fill the tank when the engine is still hot from recent operation Do not allow open flame smoking or matches in the area Avoid over filling and wipe
8. The throttle controls engine speed Move the throttle forward to increase engine speed and back to decrease engine speed Always operate at FULL throttle Choke Close the choke for cold starting Open the choke once the engine starts A warm engine may not require choking Pull the knob UP to close the choke Push to knob DOWN to open the choke H Hour Meter The hour meter measures the number of hours the PTO has been engaged The hour meter has a self contained power source so the total hours are always visible Features amp Controls Ey Fuel Tank Cap To remove the cap turn counterclockwise R Fuel Level Gauge Displays the fuel level in the tank Fuel Shut Off Valve Dual Tank Models Turning the handle to the desired position determines which tank will be supplying fuel With the handle pointing LEFT it will draw fuel from the left hand tank With the handle pointing RIGHT it will draw fuel from the right hand fuel tank With the handle pointing towards the operator it will shut off fuel flow to the engine 15 Operation Operation General Operating Safety Before first time operation Be sure to read all information in the Safety and Operation sections before attempting to operate this tractor and mower e Become familiar with all of the controls and how to stop the unit e Drive in an open area without mowing to become accustomed to the unit A WARNING Never allow passengers to ride on
9. This warranty excludes damage due to accident abuse modifications alterations improper servicing freezing or chemical deterioration Attachments or accessories that were not originally packaged with the product are also excluded There is no warranty coverage on equipment used for primary power in place of utility power or on equipment used in life support applications This warranty also excludes failures due to acts of God and other force majeure events beyond the manufacturer s control 5410603A Rev California U S EPA and Briggs amp Stratton Corporation Emissions Control Warranty Statement September 2012 Your Warranty Rights And Obligations The California Air Resources Board U S EPA and Briggs amp Stratton B amp S are pleased to explain the emissions control system warranty on your Model Year 2012 2013 engine equipment In California new small off road engines and large spark ignited engines less than or equal to 1 0 liter must be designed built and equipped to meet the State s stringent anti smog standards B amp S must warrant the emissions control system on your engine equipment for the periods of time listed below provided there has been no abuse neglect or improper maintenance of your engine or equipment Your emissions control system may include parts such as the carburetor or fuel injection system fuel tank ignition system and catalytic converter Also included may be hoses belts connectors sensors
10. traction could cause sliding Do not try to stabilize the unit by putting your foot on the ground ride on units Do not mow excessively steep slopes Do not use grass catcher on steep slopes Do not mow slopes if you cannot back up them ee EQUIPMENT RIDE ON UNITS ON OQ Tow only with a machine that has a hitch designed for towing Do not attach towed equipment except at the hitch point Follow the manufacturer s recommendations for weight limit for towed equipment and towing on slopes See attaching a trailer under OPERATION Never allow children or others in or on towed equipment On slopes the weight of the towed equipment may cause loss of traction and loss of control Travel slowly and allow extra distance to stop Do not shift to neutral and coast down hill CHILDREN Tragic accidents can occur if the operator is not alert to the presence of children Children are often attracted to the unit and the mowing activity Never assume that children will remain where you last saw them 1 Keep children out of the mowing area and under the watchful care of another responsible adult 2 Be alert and turn unit off if children enter the area 3 4 Before and during reverse operation look behind and down for small children Never carry children even with the blade s off They may fall off and be seriously injured or interfere with safe unit operation Children who have
11. 20 6m T Figure 18 Trailer Weight Recommendations A Clevis Pin B Clip www SnapperPro com Regular Maintenance Maintenance Schedule Regular Maintenance The following schedule should be followed for normal care of your rider and mower You will need to keep a record of your operating time Determining operating time is easily accomplished by observing the elapsed time recorded by the hour meter Change Hydraulic Oil amp Filter More often in hot over 85 30 C weather or dusty operating conditions Change original hydraulic oil after first 100 hours of operation More often in hot over 85 30 C weather or dusty operating conditions If equipped Replace if damaged Change original engine oil after first 5 hours of operation 25 Regular Maintenance Checking Adding Fuel To add fuel 1 Remove the fuel cap 2 Fill the tank to about 1 1 2 3 81 cm of the bottom of the filler neck This will allow for fuel expansion NOTE Do not overfill Refer to your engine manual for specific fuel recommendations 3 Install and hand tighten the fuel cap Fuel Filter The fuel filter is located in the fuel line between fuel tank and carburetor near the fuel pump If filter is dirty or clogged replace as follows 1 Disconnect the negative battery cable Place a container below the filter to catch spilled fuel Using pliers open and slide hose clamps from fuel filter
12. 25 where there is an open flame such as in a water heater Allow unit to cool before storing Shut off fuel while storing or transporting Do not store fuel near flames or drain indoors Keep all hardware especially blade attachment bolts tight and keep all parts in good working condition Replace all worn or damaged decals Never tamper with safety devices Check their proper operation regularly Disengage drives lower implement set parking brake stop engine and remove key or disconnect spark plug wire Wait for all movement to stop before adjusting cleaning or repairing Clean grass and debris from cutting units drives mufflers and engine to prevent fires Clean up oil or fuel spillage Let engine cool before storing and do not store near flame Stop and inspect the equipment if you strike an object Repair if necessary before restarting Park machine on level ground Never allow untrained personnel to service machine Use jack stands to support components when required Carefully release pressure from components with stored energy Disconnect battery or remove spark plug wire before making any repairs Disconnect the negative terminal first and the positive last Reconnect positive first and negative last Use care when checking blades Wrap the blade s or wear gloves and use caution when servicing them Only replace blades Never straighten or weld them Keep hands and feet awa
13. amp Stratton makes this information available to the consumer on our emissions labels The engine emissions label will indicate certification information The Emissions Durability Period describes the number of hours of actual running time for which the engine is certified to be emissions compliant assuming proper maintenance in accordance with the Operating amp Maintenance Instructions The following categories are used Moderate Engine is certified to be emissions compliant for 125 hours of actual engine running time Intermediate Engine is certified to be emissions compliant for 250 hours of actual engine running time Extended Engine is certified to be emissions compliant for 500 hours of actual engine running time For example a typical walk behind lawn mower is used 20 to 25 hours per year Therefore the Emissions Durability Period of an engine with an intermediate rating would equate to 10 to 12 years Briggs amp Stratton engines are certified to meet the United States Environmental Protection Agency USEPA Phase 2 or Phase 3 emissions standards The Emissions Compliance Period referred to on the Emissions Compliance label indicates the number of operating hours for which the engine has been shown to meet Federal emissions requirements For engines less than 225 cc displacement Category C 125 hours Category B 250 hours Category A 500 hours For engines of 225 cc or more displacement Category C 250 hours Categ
14. and other emissions related assemblies Where a warrantable condition exists B amp S will repair your engine equipment at no cost to you including diagnosis parts and labor Manufacturer s Warranty Coverage Small off road engines and large spark ignited engines less than or equal to 1 0 liter and any related emissions components of the equipment are warranted for two years If any emissions related part on your B amp S engine equipment is defective the part will be repaired or replaced by B amp S Two years or for the time period listed in the respective engine or product warranty statement whichever is greater Owner s Warranty Responsibilities e As the engine equipment owner you are responsible for the performance of the required maintenance listed in your owner s manual B amp S recommends that you retain all receipts covering maintenance on your engine equipment but B amp S cannot deny warranty solely for the lack of receipts or your failure to ensure the performance of all scheduled maintenance e As the engine equipment owner you should however be aware that B amp S may deny you warranty coverage if your engine equipment or a part has failed due to abuse neglect improper maintenance or unapproved modifications You are responsible for presenting your engine equipment to a B amp S distribution center servicing dealer or other equivalent entity as applicable as soon as a problem exists The warranty repairs s
15. equipped so as to conform with all applicable regulations adopted by the Air Resources Board that it is free from defects in material and workmanship that could cause the failure of a warranted part and that it is identical in all material respects to the engine described in the manufacturer s application for certification The warranty period begins on the date the engine is originally purchased The warranty on emissions related parts is as follows Any warranted part that is not scheduled for replacement as required maintenance in the owner s manual supplied is warranted for the warranty period stated above If any such part fails during the period of warranty coverage the part will be repaired or replaced by B amp S at no charge to the owner Any such part repaired or replaced under the warranty will be warranted for the remaining warranty period Any warranted part that is scheduled only for regular inspection in the owner s manual supplied is warranted for the warranty period stated above Any such part repaired or replaced under warranty will be warranted for the remaining warranty period Any warranted part that is scheduled for replacement as required maintenance in the owner s manual supplied is warranted for the period of time prior to the first scheduled replacement point for that part If the part fails prior to the first scheduled replacement the part will be repaired or replaced by B amp S at no charge to the
16. FX730 AS00 R Displacement 44 3 Cu in 726 cc Electrical System 12 Volt 15 amp Alternator Battery 340 CCA Oil Capacity 2 2 US Qt 2 1 L w Filter 28 Gross HP Briggs amp Stratton Product Model 5900830 Make Briggs amp Stratton Model 541777 0110 E1 Displacement 54 88 Cu in 896 cc Electrical System 12 Volt 20 amp Alternator Battery 340 CCA Oil Capacity 2 4 qt 2 25 L w Filter 32 Gross HP Briggs amp Stratton Product Model 5900951 amp 5900504 Make Briggs amp Stratton Model 543777 0120 E1 Displacement 54 62 Cu in 895 cc Electrical System 12 Volt 20 amp Alternator Battery 340 CCA Oil Capacity 2 4 US qt 2 3 L w Filter 25 5 Gross HPT Kawasaki Product Model 5901021 Make Kawasaki Model FX801V ES00 S Displacement 52 0 Cu in 852 cc Electrical System 12 volt 15 amp charging coil Battery 340 cca Oil Capacity 1 9 US qt 1 8 L w filter 28 Gross HP Briggs amp Stratton Commercial Turf Product Model 5901023 Make Briggs amp Stratton Model 49L977 0125 G5 Displacement 49 43 Cu in 810 cc Electrical System 12 volt 16 amp Alternator Battery 340 cca Oil Capacity 2 1 US qt 2 0 L w filter 30 Gross HP Briggs amp Stratton Commercial Turf Product Model 5900582 amp 5900583 Make Briggs amp Stratton Model 49M977 0114 G5 Displacement 49 43 Cu in 810 cc Electrical System 12 volt 16 amp alternator Battery 340 cca Oil Capaci
17. Ventilate the battery well during charging A voltmeter can be used to determine condition of battery When engine is off the voltmeter shows battery voltage which should be 12 volts When engine is running the voltmeter shows voltage of charging circuit which normally is 13 to 14 volts A dead battery or one too weak to start the engine may not mean the battery needs to be replaced For example it may mean that the alternator is not charging the battery properly If there is any doubt about the cause of the problem see your dealer If you need to replace the battery follow the steps under Cleaning the Battery amp Cables in the Regular Maintenance Section Charging a Completely Discharged Battery 1 Be aware of all the safety precautions you should observe during the charging operation If you are unfamiliar with the use of a battery charger and hydrometer have the battery serviced by your dealer 2 Add distilled water sufficient to cover the plate fill to the proper level near the end of the charge If the battery is extremely cold allow it to warm before adding water because the water level will rise as it warms Also an extremely cold battery will not accept a normal charge until it becomes warm 3 Always unplug or turn the charger off before attaching or removing the clamp connections 4 Carefully attach the clamps to the battery in proper polarity usually red to positive and black to negative 5 Whil
18. apinb si jo abpa ya ayy u Ily Z aaoge pe es pul aul p llop ay Buole Bed siy piod L La AA e SNOILONULSNI 3d07S 3H L 30 3TSNV JHL 0107103 3H1 30 ATONV AHL 34 VANOS ANIT GALLOG 31VltddOtiddV SNOTV 0103 O 9 13 ONIGIING LSOd 3ON34 310d 3341 39V48NS IVOILYSA V HLIM 35G3 SIHLNDITV _ j AGINS NOILVOI3JILN3GNI 3d07S www SnapperPro com 48 Notes Notes BRIGGS amp STRATTON PRODUCTS WARRANTY POLICY September 2012 LIMITED WARRANTY Briggs amp Stratton warrants that during the warranty period specified below it will repair or replace free of charge any part that is defective in material or workmanship or both Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser This warranty is effective for and is subject to the time periods and conditions stated below For warranty service find the nearest Authorized Service Dealer in our dealer locator map at WWW SNAPPERPRO COM The purchaser must contact the Authorized Service Dealer and then make the product available to the Authorized Service Dealer for inspection and testing There is no other express warranty Implied warranties including those of merchantability and fitness for a particular purpose are li
19. away from your vehicle before filling Remove gas powered equipment from the truck or trailer and refuel it on the ground If this is not possible then refuel such equipment on a trailer with a portable container rather than from a gasoline dispenser nozzle Keep nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete Do not use a nozzle lock open device If fuel is spilled on clothing change clothing immediately Never over fill the fuel tank Replace gas cap and tighten securely Use extra care in handling gasoline and other fuels They are flammable and vapors are explosive If fuel is spilled do not attempt to start the engine but move the machine away from the area of spillage and avoid creating any source of ignition until fuel vapors have dissipated Replace all fuel tank caps and fuel container caps securely Maintenance and Storage 1 Always observe safe refueling and fuel handling practices when refueling the unit after transportation or storage Always follow the engine manual instructions for storage preparations before storing the unit for both short and long term periods Always follow the engine manual instructions for proper start up procedures when returning the unit to service Never store the machine or fuel container inside 10 1 l 12 13 14 15 16 14 18 19 20 2 22 23 24
20. chosen ask a professional contact your local authorized dealer Children Tragic accidents can occur with children Do not allow them anywhere near the area of operation Children are often attracted to the unit and mowing activity Never assume that children will remain where you last saw them If there is a risk that children may enter the area where you are mowing have another responsible adult watch them Operator Safety Thrown Objects This unit has spinning mower blades These blades can pick up and throw debris that could seriously injure a bystander Be sure to clean up the area to be mowed and remove objects that could be thrown by the blade BEFORE you start mowing Do not operate this unit without the entire grass catcher or discharge guard deflector in place Also do nat allow anyone in the area while the unit is running If someone does enter the area shut the unit off immediately until they leave Slope Operation Operation on slopes can be dangerous Using the unit on a slope that is too steep where you do not have adequate wheel traction and control can cause sliding loss of steering control and possible rollover You should not operate on a slope greater than a 5 4 foot rise over a 20 foot length 15 degrees Always mow across slopes not up and down to maintain traction on the wheels and avoid sudden turns or rapid speed changes Reduce speed and use extreme
21. it See your authorized dealer Under no circumstance should you attempt to defeat the purpose of the safety interlock system 12 Safety Alert Symbol amp Signal Words The alert symbol A is used to identity safety information about hazards that can result in personal injury A signal word DANGER WARNING or CAUTION is used with the alert symbol to indicate the likelihood and the potential severity of the injury In addition a hazard icon may be used to represent the type of hazard An explanation of hazard levels and icons are as follows 44 DANGER This indicates a hazard which if not avoided will result in serious injury or death A WARNING This indicates a hazard which if not avoided could result in serial injury or death A CAUTION This indicates a hazard which if not avoided might result in minor or moderate injury NOTICE These messages presented without the alert symbol indicate a situation where the unit or property could be damaged www SnapperPro com Safety Icons A v A Callout Description Alert Features amp Controls Features and Controls Identification Numbers garp a S qaya CORPORATION YARD N PRODUCTS GROUP U Y E NY 13409 e ASSEM ATHE USA PART NO WAL NO N When contacting your authorized dealer for replacement parts service or information you MUST have these numbers Record your part number serial number and engine serial numbers in the
22. of the parking brake bracket D 32 Y J Figure 34 Neutral Return Adjustment A Adjustment Linkage Rod B 5 16 Nut Figure 35 Parking Brake Adjustment A Brake Spring B Adjustment Nut C Set Collar D Parking Brake Bracket www SnapperPro com Regular Maintenance CAUTION Do not adjust the spring to be shorter than 2 11 16 6 8 cm when compressed This may damage the brake mechanism 7 Turn the adjustment nut B to compress of release the spring 8 Engage the parking brake and re measure the spring Continue this process until the compressed spring length measures 2 3 4 7 cm 9 Position the set collar 1 8 0 3 cm away from the parking brake bracket and tighten If this does not correct the braking problem see your Snapper Pro dealer Deck Rod Timing Adjustment 61 Models 1 Park the machine on a flat level surface Disengage the PTO engage the parking brake turn off the engine and remove the ignition key Rear tires must be inflated to 15 psi 1 03 bar front tires to 25 psi 1 72 bar 2 To check the lift rod timing measure and record the distance between the lift pivots and the rod pivots Repeat for other side of unit See Figure 36 3 If the measurements for the rods are equal no further adjustment is required If the measurements are NOT equal greater than 1 8 3 17 mm difference adjustm
23. operate the engine on any forest covered brush covered or grass covered land unless the exhaust system is equipped with a spark arrester as defined in Section 4442 maintained in effective working order Other states or federal jurisdictions may have similar laws Contact an Authorized Service Dealer to obtain a spark arrester designed for the exhaust system installed on this engine 25 OSHA regulations may require the use of hearing protection when exposed to sound levels greater than 85 dBA for an 8 hour time period CAUTION Y This machine produces sound levels in excess of 85 dBA at the operator s ear and can cause hearing loss NI though extended periods of exposure Wear hearing protection when operating this machine SLOPE OPERATION Slopes are a major factor related to loss of control and tip over accidents which can result in severe injury or death All slopes require extra caution If you cannot back up the slope or if you feel uneasy on it do not drive on it A WARNING Do not use this machine on slopes greater than 15 Select slow ground speed before driving onto slope Use extra caution when operating on slopes with rear mounted grass catchers Mow across the face of slopes not up and down use caution when changing directions and DO NOT START OR STOP ON SLOPE Do 1 Mow across slopes not up and down 2 Remove obstacles such as rocks tree limbs etc 3 Watch fo
24. or cardboard and not hands to search for leaks Make sure all hydraulic fluid connections are tight and all hydraulic hoses and lines are in good condition before applying pressure to the system If leaks occur have the unit serviced immediately by your authorized dealer 26 WARNING Stored energy device Improper release of springs can result in serious personal injury Springs should be removed by an authorized technician 27 Models equipped with an engine radiator WARNING Stored energy device To prevent serious bodily injury from hot coolant or steam blow out never attempt to remove the radiator cap while the engine is running Stop the engine and wait until it is cool Even then use extreme care when removing the cap ROLL BAR INSTRUCTIONS For models equipped with factory installed Roll Over Protection System ROPS A WARNING In order to avoid serious injury or death from roll over it is important to follow the warnings listed below OPERATIONAL WARNINGS e Always use the seat belt when the roll bar is in the raised position Never use the seat belt when the roll bar is in the down position Remember there is no roll over protection when the roll bar is in the down position so it is very important to always keep the roll bar in the raised position whenever possible Lower the roll bar to the down position only when it is absolutely necessary Check for overhead clearances before driving under any obje
25. space provided on the inside front cover for easy access These numbers can be found in the locations shown in Figure 1 NOTE For location of engine identification numbers refer to the engine owner s manual Read the Manual Amputation Rotating Parts Pinch Point Fire Hazard Amputation Hand in Blade Amputation Foot in Blade Thrown Objects Maximum Slope Angle for Safe Operation Overhead Obstacles Rollover Hazard Tipover Keep ROPS in Raised Position Keep Children Away Slippery Slopes vV OZ Z r AS T G DM O O UD gt Dropoffs Figure 1 Identification Numbers A Identification Tag 13 Features and Controls Figure 2 Control Locations Control Functions The information below briefly describes the function of individual controls Starting stopping driving and mowing require the combined use of several controls applied in specific sequences To learn what combination and sequence of controls to use for various tasks see the OPERATION section Ground Speed Levers These levers control the ground speed of the rider The left lever controls the left rear drive wheel and the right lever controls the right rear drive wheel Moving a lever forward increases the FORWARD speed of the associated wheel and pulling back on a lever increases the REVERSE speed Note The further a lever is moved away from the neutr
26. speed is vitally important for proper mulching operation How Much Grass to Mulch The best mulching action typically results from cutting only the top 1 2 inch to 3 4 inch of grass blade This provides short clippings which decompose properly much more quickly than longer clippings The ideal cutting height will vary with climate time of year and quality of your lawn We recommend that you experiment with both the cutting height and ground speed until you achieve the best cut Start with a high cutting height and using progressively lower settings until you find a cutting height that is matched to your mowing conditions and preferences Nai Figure 17 Mulching Action ha ain 24 Attaching A Trailer The maximum weight of a towed trailer should be less than 200 Ibs 91kg Secure the trailer with a appropriately sized clevis pin A Figure 18 and clip B Excessive towed loads can cause loss of traction and loss of control on slopes Reduce towed weight when operating on slopes The surface being driven on greatly impacts traction and stability Wet or slippery surfaces can greatly reduce traction and the ability to stop or turn Carefully evaluate the surface conditions before operating the unit and trailer and never operate on slopes greater than 10 See SLOPE OPERATION and TOWED EQUIPMENT in the safety section of this manual for additional safety information 34 1m
27. the desired cutting height 3 Depress the deck lift foot pedal then push the lock lever C toward the right to release the lock 4 Release the deck lift foot pedal until it comes to rest against the cutting height adjustment pin Operation Models w Air Filled Tires Models w Flat Free Tires Figure 3 Checking Tire Pressure Figure 4 Seat Adjustment A Seat Adjustment Lever Figure 5 Mowing Height Adjustment A Cutting Height Adjustment Pin B Deck Lift Foot Pedal C Deck Lift Lock lever 17 Operation Foot Pedal Adjustment The deck lift foot pedal can be adjusted to accommodate the operator s height for optimal comfort To adjust pedal position 1 Remove the foot pedal A Figure 6 from the pedal mount tab B 2 Remove the pedal mount hardware C and rotate the tab 180 degrees 3 Reinstall the pedal mount hardware and tighten securely 4 Reinstall the foot pedal on the pedal mount tab in the proper orientation as shown in Figure 6 Raise and Lower the Roll Bar A WARNING AVOID SERIOUS INJURY OR DEATH FROM ROLL OVER Keep roll bar in the raised position and use the seat belt THERE IS NO ROLL OVER PROTECTION WHEN THE ROLL BAR IS DOWN Lower the roll bar only when necessary and NEVER remove it Do NOT use seat belt when the roll bar is down Raise the roll bar as soon as clearance permits Do NOT jump off if mower tips To Lower the Ro
28. the mower under no load condition for about 5 minutes to break in the new belt Regular Maintenance o o O o oyo JOD lo o Zo 61 Models J 72 Models Figure 47 Mower PTO Belt A Idler Arm B Stationary Idler Pulley 72 Models Figure 48 Mower PTO Belt Routing A Spindle Pulley B PTO Drive Belt C Spring loaded Idler Pulley D Stationary Idler Pulley 37 Regular Maintenance Check the Mower Belt Idler Tensioner Spring Length 1 Park the machine on a smooth level surface such as a concrete floor Disengage the PTO engage the parking brake turn off the engine and remove the ignition key 2 Lower the mower deck to its lowest cutting position 3 Measure the coil length of the mower belt tensioner spring A Figure 49 and compare with the chart below If the measurement does not match the chart adjust the mower belt idler tensioner spring length Adjusting the Mower Belt Idler Spring Length 1 Loosen the jam nut C 2 Turn the adjustment nut D until the correct measurement as indicated by the chart is achieved 3 Retighten the jam nut ea Measurement 7 1 4 1 8 18 42 cm 0 13 cm 6 3 8 1 4 16 2 cm 0 64 cm Deck Lift Assist Springs The deck lift assist springs A Figure 50 are factory set to provide optimal lifting performance Although they are fastened with an adjustable anchor this is not an adjust
29. untrained people operate or service the equipment Local regulations may restrict the age of the operator The owner user can prevent and is responsible for accidents or injuries occurring to themselves other people or property Data indicates that operators age 60 years and above are involved in a large percentage of riding mower related injuries These operators should evaluate their ability to operate the riding mower safely enough to protect themselves and others from serious injury kana kala Evaluate the terrain to determine what accessories and attachments are needed to properly and safely perform the job Use only accessories and attachments approved by the manufacturer Wear appropriate clothing including safety shoes safety glasses and ear protection Long hair loose clothing or jewelry may get tangled in moving parts Inspect the area where the equipment is to be used and remove all objects such as rocks toys and wire which can be thrown by the machine Use extra care when handling gasoline and other fuels They are flammable and vapors are explosive a Use only an approved container b Never remove fuel cap or add fuel with the engine running Allow engine to cool before refueling Do not smoke c Never refuel or drain the machine indoors Check that operator s presence controls safety switches and shields are attached and functioning properly Do not operate unless
30. up any spills Do not remove fuel filter when engine is hot as spilled gasoline may ignite DO NOT spread hose clamps further than necessary Ensure clamps grip hoses firmly over filter after installation NOTICE Do not use gasoline containing METHANOL gasohol containing more than 10 ethanol gasoline additives premium gasoline or white gas because engine fuel system damage could result Figure 19 Engine Oil Drain A Oil Drain Hose B Cap C Oil Filter D Hole for Drain Hose A WARNING Replacement parts must be the same and installed in the same position as the orginal parts or fire could result www SnapperPro com Lubrication Lubricate the unit at the locations shown in Figures 20 through 23 as well as the following lubrication points Grease e front caster wheel axles amp yokes e deck lift pivot blocks e mower deck spindles e mower deck idler arm Use grease fittings when present Disassemble parts to apply grease to moving parts when grease fittings are not installed Not all greases are compatible Red Grease p n 5022285 is recommended automotive type high temperature lithium grease may be used when this is not available Oil e control handle pivots e seat plate pivots 4 e deck lift pivots e discharge chute hinge Generally all moving metal parts should be oiled where contact is made with other parts Keep oil and grease off belts and pulleys Remember t
31. 7 11 Operator Safety Safety Interlock System This unit is equipped with safety interlock switches These safety systems are present for your safety do not attempt to bypass safety switches and never tamper with safety devices Check their operation regularly Operational SAFETY Checks Test 1 Engine should NOT crank if PTO switch is engaged OR e Parking brake is not engaged OR e Motion control handles are not in the NEUTRAL position Test 2 Engine SHOULD crank if e PTO switch is NOT engaged AND e Parking brake is engaged AND e Motion control handles are locked in the NEUTRAL position Test 3 Engine should SHUT OFF if e Operator rises off seat with PTO engaged OR e Operator rises off seat with parking brake disengaged e Operator moves motion control handles out of their neutral positions before disengaging parking brake Test 4 Blade Brake Check Mower blades and mower drive belt should come to a complete stop within seven 7 seconds after electric PTO switch is turned off or operator rises off seat If mower drive belt does not stop within seven 7 seconds see your dealer NOTE Once the engine has stopped PTO switch must be turned off parking brake must be engaged and the motion control handles must be locked in the NEUTRAL position after the operator returns to the seat in order to start the engine A WARNING If the unit does not pass a safety test do not operate
32. R label 2 Make sure there isn t any missing damaged or loose mounting hardware 3 Make sure the ROLL BAR has been correctly and completely installed EVERY 100 HOURS Inspect the ROLL BAR structure and mounting hardware for 1 Any cracks in the structure structural members and or welds 2 Significant corrosion on any part of the ROLL BAR structure or hardware 3 Missing damaged or loose mounting hardware 4 Mounting hardware that is of a grade lesser than specified 5 Machine GVW Gross Vehicle Weight including attachments restrained payload fuel and operator in excess of the maximum weight specified on the ROLL BAR label 6 Any modifications that have been made such as unauthorized welds and holes 7 Any permanent deformation or twisting of the ROLL BAR structure 8 That the ROLL BAR label is still in place and is readable 9 That the ROLL BAR on product warning labels are still on the ROLL BAR and are readable If there is any doubt as to the condition of the ROLL BAR remove the machine from service and contact your dealer for assistance 10 Operator Safety AWARNING INSPECT BUCKLE INSPECTION AND MAINTENANCE OF THE ROLL BAR SEAT BELT e The seat belt like the ROLL BAR needs to be periodically inspected to verify that the integrity has not been compromised through normal machine use misuse age degradation amp LATCH Failure to properly insp
33. Replacement NOTICE To avoid damaging belts DO NOT PRY BELTS OVER PULLEYS 1 Park the tractor on a smooth level surface such as a concrete floor Disengage the PTO engage the parking brake turn off the engine and remove the ignition key 2 Lower the mower deck to its lowest cutting position and remove the mower deck guards WARNING Use extreme caution when rotating the idler arm with the breaker bar due to the increased tension in the spring as the idler arm is being rotated Injury may result if the breaker bar is prematurely released while the spring is under tension 3 Using a 1 2 breaker bar place the square end in the square hole located in the end of the idler arm A Figures 47 Carefully rotate the breaker bar COUNTER CLOCKWISE which will relieve the tension on the belt exerted from the idler arm 4 Slide the drive belt over the edge of the stationary idler pulley B Carefully release the tension on the breaker bar or the combination wrench 5 Remove the old belt and replace with a new one Make sure the V side of the belt runs in the pulley grooves Figure 48 6 Install the drive belt on the PTO pulley the spindle pulleys and all idler pulleys except the stationary pulley B Figure 47 Carefully rotate the breaker bar COUNTER CLOCKWISE and install the belt on the stationary idler pulley B Carefully release the tension on the breaker bar 7 Reinstall the mower deck guards 8 Run
34. SMAPPER Operator s Manual S200XT Series Zero Turn Riding Mowers Description 5900830 S200XTBV2861 61 Cut Zero Turn Riding Mower 5900937 S200XTKAV2661 61 Cut Zero Turn Riding Mower 5900951 S200XTBV3261 61 Cut Zero Turn Riding Mower 5901023 S200XTB2861 61 Cut Zero Turn Riding Mower 5900582 S200XTB3061 61 Cut Zero Turn Riding Mower 5900601 S200XTBV3661 61 Cut Zero Turn Riding Mower 5901021 S200XTKAV2661 61 Cut Zero Turn Riding Mower 5900504 S200XTBV32 Zero Turn Riding Mower 5900583 S200XTB30 Zero Turn Riding Mower 5900585 S200XTBV36 Zero Turn Riding Mower 5900505 S200XT 72 72 Cut Mower Deck This manual is available in Spanish For a copy contact your Snapper Pro dealer or www snapperpro com Este manual esta disponible en Espanol Para obtener una copia p ngase en contacto con su distribuidor Snapper Pro o www snapperpro com BRIGGS amp STRATTON POWER PRODUCTS GROUP LLC 5375 NORTH MAIN STREET 5102188 MUNNSVILLE NY 13409 Revision J 800 933 6175 Thank you for purchasing this quality built SNAPPER PRO product We re pleased that you ve placed your confidence in the SNAPPER PRO brand When operated and maintained according to the instructions in this manual your SNAPPER PRO product will provide many years of dependable service This manual contains safety information to make you aware of the hazards and risks associated with this machine and how to avoid them This machine is designed and
35. ach mower blade with the air lifts pointing up towards the mower deck as shown in Figure 31 Secure with the mower blade mounting bolt and flat washer A amp B Figure 31 and torque to 70 ft Ibs 94 Nm 2 If there are no flats on the spindle shaft wedge a wooden block between the mower blade and the mower deck housing to keep the mower blade from turning 30 Figure 29 Sharpening the Mower Blade A Mower Blade Bevel B Mower Blade Cutting Edge Figure 30 Balancing the Mower Blade A Nail Figure 31 Tightening the Mower Blade for Installation A Mower Blade Mounting Bolt B Flat Washer C Mower Blade Air Lift Points Up For Installation D 4 X 4 Wooden Block www SnapperPro com Ground Speed Control Lever Adjustment The control levers can be adjusted in three ways The alignment of the control levers the placement of the levers how close the ends are to one another and the height of the levers can be adjusted To Adjust the Handle Alignment Loosen the mount bolts A Figure 32 and pivot the lever s B to align with each other To Adjust the Handle Placement Loosen the jam nuts and adjust the placement bolt C Figure 33 in or out to properly adjust the lever end spacing To Adjust the Handle Height Remove the mounting hardware and reposition the handle either up or down from its original position You will need to readjust the handl
36. al position the faster the drive wheel will turn See the Operation section for proper steering instructions 14 Seat Adjustment Lever The seat can be adjusted forward and back Move the lever towards the left position the seat as desired and release the lever to lock the seat in position Ignition Switch The ignition switch starts and stops the engine it has three positions e OFF Stops the engine and shuts off the electrical system El RUN Allows the engine to run and powers the electrical system START Crnanks the engine for starting NOTE Never leave the ignition switch in the RUN position with the engine stopped this drains the battery www SnapperPro com Parking Brake Releases the parking brake DISENGAGE Locks the parking brake ENGAGE Pull the parking brake lever back to engage the parking brake Move the lever fully forward to disengage the parking brake NOTE To start the unit the parking brake must be engaged kal PTO Power Take Off Switch The PTO switch engages and disengages the mower Pull UP on the switch to engage and push DOWN to disengage tas Deck Lift Pedal Cutting Height y Adjustment Pin amp Deck Lift Lock Lever These control the cutting height of the mower deck Depress the pedal until it locks into the 6 15 2 cm position Place the adjustment pin in the desired cutting height and release the lift lock lever e Throttle Control
37. been given rides in the past may suddenly appear in the mowing area for another ride and be run over or backed over by the machine Never allow children to operate the unit Use extra care when approaching blind corners shrubs trees or other objects that may obscure vision Operator Safety EMISSIONS 1 Engine exhaust from this product contains chemicals known in certain quantities to cause cancer birth defects or other reproductive harm Look for the relevant Emissions Durability Period and Air Index information on the engine emissions label IGNITION SYSTEM GASOLINE MODELS l This spark ignition system complies with Canadian ICES 002 SERVICE AND MAINTENANCE To avoid personal injury or property damage use extreme care in handling gasoline Gasoline is extremely flammable and the vapors are explosive Safe Handling of Gasoline 1 Extinguish all cigarettes cigars pipes and other 10 1 k 12 13 sources of ignition Use only approved gasoline containers Never remove the gas cap or add fuel with the engine running Allow the engine to cool before refueling Never fuel the machine indoors Never store the machine or fuel container where there is an open flame spark or pilot light such as near a water heater or other appliance Never fill containers inside a vehicle or ona truck bed with a plastic bed liner Always place containers on the ground
38. caution on ALL slopes Also note that the surface condition you are on can greatly impact your ability to safely operate this machine Operating on wet or slippery slopes can cause sliding and loss of steering and control Do not operate on slopes that are slippery wet or have soft soil conditions If you feel unsure about operating the unit on a slope don t do it It s not worth the risk Moving Parts This equipment has many moving parts that can injure you or someone else However if you stay in the operator zone stay seated in the seat and follow the safety rules in this operators manual the unit is safe to operate The mower deck has spinning mower blades that can amputate hands and feet Do not allow anyone near the unit while it is running Keep safety devices guards shields and switches in place and working To help you the operator use this equipment safely it is equipped with an operator present safety system Do NOT attempt to alter or bypass the system See your dealer immediately if the system does not pass all the safety interlock system tests found in this manual Operator Safety Retaining Walls Drop offs and Water Retaining walls and drop offs around steps and water are a common hazard Give yourself a minimum of two mower widths of clearance around these hazards and hand trim with a walk behind mower or string trimmer Wheels dropping over retaining wa
39. cts Do not allow roll bar to contact low overhanging obstacles such as tree branches and guide wires Never remove the roll bar from the vehicle Do not exceed the machine weight rating of the roll bar Read and follow all of the instructions shown below regarding the inspection and maintenance of the roll bar structure and the seat belt INSPECTION OF THE ROLL BAR PROTECTIVE STRUCTURE A WARNING Failure to properly inspect and maintain the ROLL BAR protective structure can cause serious injury or death A ROLL BAR like any other safety device needs to be periodically inspected to verify that the integrity of the device has not been compromised through normal machine use misuse age degradation modifications or a roll over Operator Safety To maintain operator roll over protection and roll bar effectiveness e If a ROLL BAR becomes damaged for any reason such as a collision roll over or impact the ROLL BAR must be replaced Small undetectable cracks can reduce the effectiveness of the ROLL BAR Never weld straighten or repair the ROLL BAR Never alter the ROLL BAR by welding anything to it or by drilling additional holes BEFORE FIRST TIME USE Inspect the ROLL BAR structure and mounting hardware for 1 Check to make sure the machine GVW Gross Vehicle Weight including attachments restrained payload fuel and operator is not in excess of the maximum weight specified on the ROLL BA
40. dition If notch measures 25 6 35 mm or greater DO NOT USE Replace with new mower blade 29 Regular Maintenance Sharpening the Mower Blade CAUTION Avoid injury Mower blades are sharp e Always wear gloves when handling the mower blades e Always wear safety eye protection when grinding 1 Sharpen the mower blades with grinder hand file or electric blade sharpener 2 Sharpen the mower blade by removing an equal amount of material from each end of the mower blade 3 Keep the original bevel A Figure 29 when grinding DO NOT change the mower blade bevel 4 The mower blade should have a maximum 1 64 0 40 mm cutting edge B or less 5 Balance the mower blades before installing Balancing the Mower Blades CAUTION Avoid injury Keep mower blades balanced e An unbalanced mower blade can create excessive vibration and damage the unit or cause mower blade failure 1 Clean the mower blade to remove any dried grass or other debris 2 See Figure 30 Put the mower blade on a nail in a vise and turn the mower blade to the horizontal position 3 Check the balance of the mower blade If either end of the mower blade moves downward sharpen the heavy end until the mower blade is balanced See Sharpening the Mower Blades for proper sharpening instructions 4 Repeat the process until the mower blade remains in the horizontal position Reinstalling the Mower Blades 1 Reinstall e
41. e alignment as described above Speed Balancing Adjustment If the rider veers to the right or left when the ground speed control levers are in the maximum forward position the top speed of each of these levers can be balanced by turning the adjustment bolt s A Figure 33 Only adjust the speed of the wheel that is traveling faster To Reduce the Speed of the Faster Wheel 1 Loosen the securing nut 2 Turn the top speed adjustment bolt COUNTER CLOCKWISE to reduce the speed 3 Retighten the securing nut when adjustment is complete AWARNING DO NOT adjust the tractor for a faster overall speed forward or reverse than it was designed for Regular Maintenance Figure 32 Control Lever Adjustment A Placement Hardware B Ground Speed Control Lever e Figure 33 Top Speed Adjustment A Top Speed Adjustment Bolt B Control Lever Base C Alignment Hardware 31 Regular Maintenance Neutral Adjustment If the tractor creeps while the ground speed control levers are locked in NEUTRAL then it may be necessary to adjust the linkage rod NOTE Perform this adjustment on a hard level surface such as a concrete floor 1 Disengage the PTO engage the parking brake and turn off the engine 2 There are two nuts B Figure 34 on the linkage rod Loosen the nuts from the ball joints and turn the linkage rod A t
42. e blades when not mowing Never operate with guards not securely in place Be sure all interlocks are attached adjusted properly and functioning properly Never operate with the discharge deflector raised removed or altered unless using a grass catcher Do not change the engine governor setting or overspeed the engine Stop on level ground lower implements disengage drives engage parking brake shut off engine before leaving the operator s position for any reason including emptying the grass catchers or unclogging the chute Stop equipment and inspect blades after striking objects or abnormal vibration occurs Make necessary repairs before resuming operations Keep hands and feet away from the cutting units Look behind and down before backing up to be sure of a clear path Never carry passengers and keep pets and bystanders away Do not operate the unit while under the influence of alcohol or drugs Slow down and use caution when making turns and crossing roads and sidewalks Stop blades if not mowing Use care when loading or unloading the machine into a trailer or truck 23 Use care when approaching blind corners shrubs trees or other objects that may obscure vision 24 To reduce fire hazard keep unit free of grass leaves amp excess oil Do not stop or park over dry leaves grass or combustible materials A WARNING It is a violation of California Public Resource Code Section 4442 to use or
43. e charging periodically measure the temperature of the electrolyte If the temperature exceeds 125 F 51 6 C or if violent gassing or spewing of electrolyte occurs the charging rate must be reduced or temporarily halted to prevent battery damage 6 Charge the battery until fully charged until the specific gravity of the electrolyte is 1 250 or higher and the electrolyte temperature is at least 60 F The best method of making certain a battery is fully charged but not over charged is to measure the specific gravity of a cell once per hour The battery is fully charged when the cells are gassing freely at low charging rate and less than 0 003 change in specific gravity occurs over a three hour period Regular Maintenance Jump Starting With Auxiliary Booster Battery Jump starting is not recommended However if it must be done follow these directions Both booster and dis charged batteries should be treated carefully when using jumper cables Follow the steps below EXACTLY being careful not to cause sparks Refer to Figure 53 1 Both batteries must be of the same voltage 2 Position the vehicle with the booster battery adjacent to the vehicle with the discharged battery so that booster cables can be connected easily to the batteries in both vehicles Make certain vehicles do not touch each other 3 Wear safety glasses and shield eyes and face from batteries at all times Be sure vent caps are tight Place damp clo
44. e majority of the adjustment and the fine adjustment procedure should be used to complete the adjustment 1 Park machine on a flat level surface Disengage the PTO stop the engine and engage the parking brake Rear tires must be inflated to 15 psi 1 03 bar front tires to 25 psi 1 72 bar 2 Lock the deck lift pedal in the 6 15 2 cm position Place the deck height adjustment pin in the 4 position and lower deck the lift pedal until the arm contacts the pin 3 Place 2 x 4 blocks under each corner of the mower deck with the 3 1 2 sides being vertical See Figure 38 4 Loosen the nuts and allow the front of the deck to rest on the 2 x 4 s Slide the chains down in the slots until the chains are tight and tighten the nuts See Figure 39 5 Loosen the nuts and allow the rear of the deck to rest on the 2 x 4 s Slide the chains down in the slots until the chains are tight and tighten the nuts See Figure 39 6 Remove all 2 x 4 blocks from under the mower deck 7 For your safety DO NOT handle mower blades with bare hands Position the outside mower blades so that they face front to back Figure 40 8 Measure from the front tip of the blade from the cutting edge to the ground Measure from the rear tip of the blade from the cutting edge to the ground Repeat this process for the other side of the machine The front and back measurements should be 4 10 2 cm If the measurements are greater than 1 8 3 17 mm o
45. e preceding could result in 1 personal injury caused by electrolyte squirting out the battery vents 2 personal injury or property damage due to battery explosion 3 damage to the charging system of the booster vehicle or of the immobilized vehicle Do not attempt to jump start a vehicle having a frozen battery because the battery may rupture or explode If a frozen battery is suspected examine all fill vents on the battery If ice can be seen or if the electrolyte fluid cannot be seen do not attempt to start with jumper cables as long as the battery remains frozen 42 A WARNING For your personal safety use extreme care when jump starting Never expose battery to open flame or electric spark battery action generates hydrogen gas which is flammable and explosive Do not allow battery acid to contact skin eyes fabrics or painted surfaces Batteries contain a sulfuric acid solution which can cause serious personal injury or property damage When removing or installing battery cables disconnect the negative cable FIRST and reconnect it LAST If not done in this order the positive terminal can be shorted to the frame by a tool To avoid engine damage do not disconnect battery while engine is running Be sure terminal connections are tight before starting www SnapperPro com Storage Temporary Storage 30 Days Or Less Remember the fuel tank will still contain some gasoline so never s
46. ealer only service tem 1 Locate the hydraulic oil filter A Figure 25 on the side of the transaxle 2 Remove the filter cover C and o ring B 3 Inspect all parts for wear or damage replacing as necessary 4 Remove and discard the hydraulic filter 5 Install the new filter new o ring and filter cover Torque the cover to 40 45 ft lbs 54 61 Nm 6 Add new hydraulic oil to the hydraulic oil reservoir until the FULL COLD mark is reached 7 Run the unit for several minutes and check the transmission oil level and add as necessary IMPORTANT NOTE Use caution after changing the filter air in the hydraulic system may affect the responsiveness of the control levers 28 L D Z Figure 24 Checking Hydraulic Oil Level A Hydraulic Oil Reservoir B Reservoir Cap Figure 25 Intergrated Transmission A Hydraulic Oil Filter B O Ring C Filter Cover www SnapperPro com Servicing The Mower Blades Removing the Mower Blade CAUTION Avoid injury Mower blades are sharp e Always wear gloves when handling mower blades or working near blades 1 To remove the mower blade use a 1 wrench on the flats of the spindle shaft and remove the mower blade mounting bolt with a 15 16 wrench Figure 26 2 If there are no flats on the spindle shaft wedge a wooden block between the mower blade and the mower deck housing to keep the mower blade from turning
47. ect and maintain the seat belt can cause serious injury or death O modifications or a roll over If the seat belt does lt INSPECT WEBBING not pass all of the following tests it should be y replaced BEFORE EACH USE Conduct the following inspections maintenance of the seat belt and retraction mechanism 1 Check for dirt or debris in the retraction mechanism If dirt or debris is found it should be removed 2 Check to make sure the retraction mechanism retracts easily and completely e Check for damage to any part of the seat belt such as nicks cuts loose stitching or fraying Check that the buckle and latch operate properly and that the latch plate is not excessively worn deformed or the buckle is damaged or cracked The seat belt should latch and release easily C 5 Safety Decals Before operating your unit read the safety decals The cautions and warnings are for your safety To avoid a personal injury or damage to the unit understand and follow all safety decals A WARNING If any safety decals become worn or damaged and cannot be read order replacement decals from your local dealer These decals are located on the guards above the transmission fans These decals are located behind the ROPS on the frame of the unit Operator Safety B anancer 3 Amputation and thrown objects hazard Keep hands and feet Do not operate mower z awa
48. ency of the blades and prevents many common cutting problems Use an appropriate ground speed for the thickness and height of the grass you are cutting 3rd gear or slower for manual gear models If you hear the engine slowing down you are mowing too fast use a slower ground speed Operation Where possible make one or two passes around the outside of the area discharging the grass INTO the lawn to keep the cut grass off fences and walks The remainder of the mowing should be done in the opposite direction so that the clippings are dispersed OUT onto the area of lawn previously cut Mowing Methods Proper Broadcast Mowing Broadcasting or side discharging disperses fine clippings evenly over the entire lawn Many golf courses use this method Your mower has a deep dish deck to allow freer circulation of clippings so they are broadcast evenly over the lawn Engine Speed amp Ground Speed for Broadcasting Always operate the engine at full throttle when mowing If you hear the engine slowing down you are mowing too fast using a slower ground speed will improve the cutting efficiency of the blades and prevents many common cutting problems ALWAYS use an appropriate ground speed for the thickness and height of the grass you are cutting 3rd gear or slower for manual gear models If you hear the engine slowing down you are mowing too fast use a slower ground speed How Much Grass to Cut Off When Broadcasting Mow whe
49. ent is required continue with Step 4 4 Lock the deck lift pedal in the 6 15 2 cm position Remove the cutting height adjustment pin and lower the mower deck 5 To ensure that the deck is in the lowest position push the pedal by hand towards the rear of the unit and install the height adjustment pin in the 3 7 6 cm position to hold in place 6 Block up the mower deck until all hanger chains are slack Refer to Figure 38 7 See Figure 37 To adjust the lift rod loosen the jam nut on the front clevis then remove the 1 2 clevis pin fastening the clevis to the lift pivot arm Turn the clevis clockwise to shorten the distance between the rod pivots or counterclockwise to lengthen the distance between the rod pivots Reinstall the clevis on the lift pivot arm and secure with the 1 2 clevis pin previously removed Tighten the jam nut against the clevis 8 Remove the blocks from the under the mower deck 9 Remove the cutting height adjustment pin from in front of the deck lift pedal arm Lift mower deck and reinstall adjustment pin in desired mowing height Measure First Figure 38 2 x 4 Locations 33 Regular Maintenance Deck Leveling Adjustment 61 Models NOTE Before adjusting the deck level the deck lift rod timing must be checked and or adjusted Coarse Adjustment Procedure When adjusting the deck level the coarse adjustment procedure should be used to make th
50. et tightly with plastic or other waterproof material to keep out moisture dirt and insects 7 Completely grease and oil unit as outlined in the Normal Care section 8 Clean up unit and apply paint or rust preventative to any areas where paint is chipped or damaged 9 Be sure the battery is filled to the proper level with water and is fully charged Battery life will be increased if it is removed put in a cool dry place and fully charged about once a month If battery is left in unit disconnect the negative cable Regular Maintenance AWARNING Never store the unit with gasoline in engine or fuel tank in a heated shelter or in enclosed poorly ventilated enclosures Gasoline fumes may reach an open flame spark or pilot light such as a furnace water heater clothes dryer etc and cause an explosion Handle gasoline carefully It is highly flammable and careless use could result in serious fire damage to your person or property Drain fuel into an approved container outdoors away from open flame or sparks 10 Drain fuel system completely or add a gasoline stabilizer to the fuel system If you have chosen to use a fuel stabilizer and have not drained the fuel system follow all safety instructions and storage precautions in this manual to prevent the possibility of fire from the ignition of gasoline fumes Remember gasoline fumes can travel to distant sources of ignition and ignite causing risk of explosion and fire
51. f what they should be adjust the deck height until they are correct Fine Adjustment 1 Loosen the jam nut A Figure 41 and turn the fine adjustment bolt B to adjust the deck height until the front measurements equals 4 10 2 cm Turn the bolt CLOCKWISE to raise the deck COUNTER CLOCKWISE to lower the deck 2 Position the outside mower blades so they face front to back 3 Remeasure the front tip of the blade from the cutting edge to the ground Measure the rear tip of the blade from the cutting edge to the ground Repeat the process for the other side of machine 4 Once the measurement equals 4 10 2 cm retighten the jam nut 34 Adjust Here Figure 39 Hanger Chain Adjustment AA Figure 40 Checking The Blade Height Measurement Figure 41 Fine Adjustment A Jam Nut B Fine Adjustment Bolt www SnapperPro com Regular Maintenance Vez Y lt A S E Measure Y Second gt Measure First p Deck Rod Timing Adjustment 72 Models 1 Park the machine on a flat level surface Disengage the PTO engage the parking brake turn off the engine and remove the ignition key Rear tires must be inflated to 15 psi 1 03 bar 2 To check lift rod timing measure and record the distance between the lift pivots and the rod pivots Repeat for other side of the unit See Figure 42 3 If the measurements for the rods are equal no furt
52. g anchor eyebolt G into the anchor tab and loosely fasten the nut Adjust the anchor eyebolt until a measurement of 6 3 8 16 2 cm is achieved from spring body Tighten nut Reinstall the clutch anchor pad to the PTO clutch and secure with the hardware previously removed Reinstall the PTO drive belt 39 Regular Maintenance Battery Maintenance NOTE This unit is equipped with a maintenance free BCIU1 battery Cleaning the Battery and Cables A WARNING Be careful when handling the battery Avoid Spilling electrolyte Keep flames and sparks away from the battery When removing or installing battery cables disconnect the negative cable FIRST and reconnect it LAST If not done in this order the positive terminal can be shorted to the frame by a tool 1 Disconnect the cables from the battery negative black cable first B Figure 52 2 Clean the battery terminals and cable ends with a wire brush until shiny 3 Reinstall the battery and reattach the battery cables positive red cable first A 4 Coat the cable ends and battery terminals with petroleum jelly or non conducting grease 40 Figure 52 Battery Compartment A Positive Cable amp Terminal B Negative Cable amp Terminal www SnapperPro com Battery Service Checking Battery Voltage WARNING Keep open flames and sparks away from the battery the gasses coming from it are highly explosive
53. gh the forward reverse and turning maneuvers You must release the parking brake prior to moving the control levers inward Forward Travel Practice Gradually move both ground speed control levers evenly FORWARD from neutral Slow down and repeat NOTE Straight forward travel takes practice If necessary top speed can be balance adjusted see the Speed Balancing Adjustment in the Adjustments section near the back of this manual Smooth Travel The lever controls of the Zero Turn rider are responsive The BEST method of handling the ground speed control levers is in three steps as shown in Figure 9 FIRST place your hands onto the levers as shown SECOND to go forward gradually push the levers forward with your palms THIRD to speed up move the levers farther forward To slow down smoothly slowly move the levers toward neutral Figure 9 Move Control Levers Gradually Reverse Travel Practice LOOK DOWN amp BEHIND then gradually move both ground speed control levers evenly BACK from neutral Slow down and repeat NOTE Practice backing up for several minutes before attempting to do so near objects The rider turns sharply in reverse as well as forward and backing up straight takes practice Forward Travel Reverse Travel Figure 10 Forward Travel 20 Figure 11 Reverse Travel
54. her adjustment is required If measurements are not equal greater than 1 8 3 17 mm difference adjustment is required continue with step 4 4 Lock the deck lift pedal in the 6 15 2 cm position Figure 42 Check Lift Rod Timing Remove the cutting height adjustment pin and lower the mower deck 5 To ensure that the deck is in the lowest position push the pedal by hand towards the rear of the unit and install the height adjustment pin in the 3 7 6 cm position to hold in place 6 Block up the mower deck until all hanger chains are slack Refer to Figure 43 7 See Figure 44 To adjust the lift rod loosen the jam nut on the front clevis then remove the 1 2 clevis pin fastening the clevis to the lift pivot arm Turn the clevis clockwise to shorten the distance between the rod pivots or counter clockwise to lengthen the distance between the rod pivots Reinstall the clevis on the lift pivot arm and secure with the 1 2 clevis pin previously removed Tighten the jam nut against the clevis 8 Remove the blocks from under the mower deck 9 Remove the cutting height adjustment pin from in front of the deck lift pedal arm Lift mower deck and reinstall adjustment pin in desired mowing height Figure 44 Adjust Lift Rod Timing 35 Regular Maintenance Deck Leveling Adjustment 72 Models NOTE Before adjusting the deck level the deck lift rod timing must be checked and or ad
55. hould be completed in a reasonable amount of time not to exceed 30 days If you have any questions regarding your warranty rights and responsibilities you should contact B amp S at 414 259 5262 Briggs Stratton Emissions Control Warranty Provisions The following are specific provisions relative to your Emissions Control Warranty Coverage It is in addition to the B amp S engine warranty for non regulated engines found in the Operator s Manual 1 Warranted Emissions Parts Coverage under this warranty extends only to the parts listed below the emissions control systems parts to the extent these parts were present on the B amp S engine and or B amp S supplied fuel system a Fuel Metering System e Cold start enrichment system soft choke Carburetor and internal parts e Fuel pump Fuel line fuel line fittings clamps Fuel tank cap and tether e Carbon canister b Air Induction System Air cleaner Intake manifold Purge and vent line c Ignition System Spark plug s e Magneto ignition system d Catalyst System e Catalytic converter e Exhaust manifold Air injection system or pulse valve e Miscellaneous Items Used in Above Systems Vacuum temperature position time sensitive valves and switches Connectors and assemblies 2 Length of Coverage For a period of two years from date of original purchase B amp S warrants to the original purchaser and each subsequent purchaser that the engine is designed built and
56. in open position 2 Belt is broken 3 Drive belt slips 4 Brake is not fully released 1 Pulleys or belt greasy or oily 2 Tension too loose 3 Belt stretched or worn 1 Brake is incorrectly adjusted 2 Brake pads worn 1 Steering linkage is loose 2 Improper tire inflation Cause 1 Lift linkage not properly attached or damaged 1 Engine speed too slow 2 Ground speed too fast 3 Cutting height set too low 4 Discharge chute jamming with cut grass 1 Blade mounting bolts are loose 2 Mower blades arbors or pulleys are bent 3 Mower blades are out of balance 4 Belt installed incorrectly 1 Bent or rough pulleys 2 Using incorrect belt 1 Idler pulley spring broken or not properly attached 2 Mower drive belt broken 1 Electrical wiring damage 2 PTO clutch not adjusted 3 Battery voltage too low Nr cs ro s r o ro A N oo k roo Jx e r S Troubleshooting Remedy Turn valve s clockwise to close _ See Drive Belt Replacement See problem and cause below See authorized service dealer Clean as required Adjust spring tension See Drive Belt Replacement Replace belt See Brake Adjustment Replace with new brake pads Check and tighten any loose connections See Regular Maintenance Section Remedy k See authorized service dealer for repair Set to full throttle Decrease Ground Speed
57. intended to be used and maintained according to the manual and operated by trained professionals for finish cutting of established lawns and is not intended for any other purpose It is important that you read and understand these instructions thoroughly before attempting to start or operate this equipment Save these original instructions for future reference PRODUCT REFERENCE DATA Unit SERIAL Number Mower Deck Model Number Mower Deck SERIAL Number Unit Model Number u ENGINE REFERENCE DATA Engine Make Engine Model Engine Type Spec Engine Code Serial Number See Features and Controls for the location of Identification Numbers Briggs amp Stratton Power Products Group LLC Copyright 2012 Briggs amp Stratton Power Products Group LLC Milwaukee WI USA All rights reserved SNAPPER PRO is a trademark of Briggs amp Stratton Power Products Group LLC Contact Information Briggs amp Stratton Power Products Group LLC 5375 N Main St Munnsville NY 13409 4003 800 933 6175 www SnapperPro com A WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer birth defects or other reproductive harm AWARNING Battery posts terminals and related accessories contain lead and lead compounds chemicals known to the State of california to cause cancer and reproductive harm Wash hands after handling Table of Contents Operator Safety
58. justed 1 36 Park the machine on a flat level surface Disengage the PTO stop the engine and engage the parking brake Check tires for proper inflation Lock the deck lift pedal in the 6 15 2 cm position Place the deck height adjustment pin in the 4 position and lower deck the lift pedal until the arm contacts the pin Place 2 x 4 blocks under each corner of the mower deck with the 3 1 2 sides being vertical See Figure 43 Loosen the jam nut A Figure 45 on the deck hanger Turn the deck height adjuster B clockwise to raise the deck or counter clockwise to lower the deck until the deck rests on the 2 x 4 s Remove all 2 x 4 blocks from under the mower deck For your safety DO NOT handle mower blades with bare hands Position the outside mower blades so that they face front to back Figure 46 Measure from the front tip of the blade from the cutting edge to the ground Measure from the rear tip of the blade from the cutting edge to the ground Repeat this process for the other side of the machine The front and back measurements should be 4 10 2 cm If the measurements are greater than 1 8 3 17 mm of what they should be adjust the deck height until they are correct Figure 45 Hanger Chain Adjustment A Jam Nut B Deck Height Adjuster yY AA Figure 46 Checking The Blade Height Measurement www SnapperPro com Mower Belt
59. ll Bar 1 Pull the hair pin clips A Figure 7 out of the retainer pins B 2 Push or pull the top of the roll bar C forward against the rubber stops D and remove the retainer pins B 3 Lower the roll bar into the down position see insert Figure 8 To Raise the Roll Bar 1 Pull the hair pin clips A out of the retainer pins B and remove the retainer pins 2 Raise the roll bar C until the rubber stops D contact the upright tubes 3 Push or pull the top of the roll bar forward against the rubber stops and reinstall the retainer pins and hair pin clips to secure the roll bar in the raised position 18 Figure 6 Foot Pedal Adjustment A Deck Lift Foot Pedal B Pedal Mount Tab C Pedal Mount Hardware D Optional Position Figure 7 Raise amp Lower the Roll Bar A Hair Pin Clip B Retainer Pin C Roll Bar D Rubber Stop www SnapperPro com Starting the Engine AWARNING If you do not understand how a specific control functions or have not yet thoroughly read the FEATURES amp CONTROLS section do so now Do NOT attempt to operate the tractor without first becoming familiar with the location and function of ALL controls 1 While sitting in the operator s seat engage the parking brake by pulling the parking brake lever back make sure the PTO switch is disengaged pressed down fully and the motion control handles are locked in the NEUTRAL
60. lls edges ditches embankments or into water can cause rollovers which may result in serious injury death or drowning Roll Bar Use Keep the roll bar in the raised position and fasten the seat belt There is no roll over protection when the roll bar is down Do not jump off if the mower tips it is safer to be secured by the seat belt with the roll bar raised Lower the roll bar only when necessary such as to temporarily clear a low overhanging obstacle and NEVER remove it Do NOT use the seat belt when the roll bar is down Raise the roll bar as soon as clearance permits Overhead Obstacles Check for overhead clearances before driving under any objects Do not allow the roll bar to contact low overhanging obstacles such as tree branches and guide wires Enclosed Areas Only operate this unit outdoors and away from unventilated areas such as inside garages or enclosed trailers The engine emits poisonous carbon monoxide gas and prolonged exposure in an enclosed area can result in serious injury or death Operator Safety Fuel and Maintenance Always disengage all drives shutoff the engine and remove the key before doing any cleaning refueling or servicing Gasoline and its vapors are extremely flammable Do not smoke while operating or refueling Do not add fuel while engine is hot or running Allow engine to cool for at least 3 minutes prior to adding fuel Do not add fuel i
61. ment point Do NOT attempt to adjust the spring length or lifting performance will be compromised 38 Figure 49 Mower Belt Idler Spring Length A Mower Belt Tensioner Spring B Measurment C Jam Nut D Adjustment Nut Figure 50 Deck Lift Assist Spring Location A Deck Lift Assist Spring www SnapperPro com Regular Maintenance Hydraulic Pump Drive Belt Replacement 1 Park the tractor on a smooth level surface such as a concrete floor Disengage the PTO engage the parking brake turn off the engine and remove the ignition key 2 Remove the PTO drive belt see MOWER BELT REPLACEMENT for removal instructions 3 Remove the hardware that secures the clutch anchor pad to the PTO clutch A WARNING STORED ENERGY DEVICE Improper release of the belt tension spring can result in personal injury Use extreme caution when removing this spring 4 Loosen the nut on the spring anchor eyebolt G Figure Figure 51 Hydraulic Drive Belt Replacement 51 to release the majority of the belt tension Use A Pump Drive Belt caution and remove the nut to completely release the B Crankshaft Pulley tension C Transaxle Pulley ass D Idler Pulley 5 Remove the old belt and replace it with the new one E daler Arm Make sure the V side of the belt runs in the grooves of F Spring the crankshaft pulley and transaxle pulleys B amp C G Spring Anchor Eyebolt Reinstall the sprin
62. mited to one year from purchase or to the extent permitted by law All other implied warranties are excluded Liability for incidental or consequential damages are excluded to the extent exclusion is permitted by law Some states or countries do not allow limitations on how long an implied warranty lasts and some states or countries do not allow the exclusion or limitation of incidental or consequential damages so the above limitation and exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state or country to country WARRANTY PERIOD Covered Parts Standard Warranty Period Rental Warranty Period Riding mowers 4 years 48 months or 500 hours whichever occurs first 90 days Unlimited hours during the first 2 years 24 months Except as noted below Walk mowers 2 years 24 months unlimited hours 90 days over 30 inches of cutting width Except as noted below Belts Tires Brake Pads 90 days 90 days Hoses Battery Blades Attachments 1 year 90 days Engine See Engine Operator s Manual See Engine Operators Manual Emissions related components are covered by the Emissions Warranty Statement In Australia Our goods come with guarantees that cannot be excluded under the Australian Consumer Law You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage You are also e
63. n the grass is 3 5 inches long Do not cut the grass shorter than 2 to 2 1 2 inches Do not cut off more that 1 inch of grass in a single pass 23 Operation Proper Mulching Mulching consists of a mower deck which cuts and recuts clippings into tiny particles and which then blows them down INTO the lawn These tiny particles decompose rapidly into by products your lawn can use UNDER PROPER CONDITIONS your mulching mower will virtually eliminate noticeable clippings on the lawn surface NOTE When mulching under heavy cutting conditions a rumbling sound may be present and is normal Mulching Requires EXCELLENT Mowing Conditions Mulching mowers cannot function properly if the grass is wet or if the grass is simply to high to cut Even more than normal mowing mulching requires that the grass be dry and the the appropriate amount is cut Do not use the mower as a mulching mower during the first two or three mowings in the spring The long grass blades quick growth and often wetter conditions are more suitable for broadcasting side discharging or grass bagging operation Engine Speed amp Ground Speed for Mulching Use full engine throttle matched with a slow ground speed so that clippings will be finely cut Ground speed while mulching should be HALF of the speed that would be used when broadcasting side discharging under similar conditions Since mulching requires more horsepower than broadcasting using a slower ground
64. ndoors in an enclosed trailer garage or any other enclosed area that is not well ventilated Gasoline spills should be cleaned up promptly and before operation begins Gasoline should be stored only in sealed containers approved for fuel Proper maintenance is critical to the safety and performance of your unit Keep the unit free of grass leaves and excess oil Be sure to perform the maintenance procedures listed in this manual especially periodically testing the safety system Operator Safety A Read these safety rules and follow them closely Failure to obey these rules could result in loss of control of unit severe personal injury or death to you or bystanders or damage to property or equipment This mowing deck is capable of amputating hands and feet and throwing objects The triangle 4 in text signifies important cautions or warnings which must be followed TRAINING Read understand and follow all instructions in the manual and on the unit before starting If the operator s or mechanic s can not read English it is the owner s responsibility to explain this material to them Become familiar with the safe operation of the equipment operator controls and safety signs All operators and mechanics should be trained The owner is responsible for training the users Only allow responsible adults who are familiar with the instructions to operate the unit Never let children or
65. ntitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure For warranty service find the nearest Authorized Service Dealer in our dealer locator map at FERRISINDUSTRIES COM AU or by calling 1300 274 447 or by emailing or writing to salesenquires briggsandstratton com au Briggs amp Stratton Australia Pty Ltd 1 Moorebank Avenue NSW Australia 2170 The warranty period begins on the date of purchase by the first retail end user and continues for the period of time or hours stated in the table above No warranty registration is necessary to obtain warranty on Briggs amp Stratton products Save your proof of purchase receipt If you do not provide proof of the initial purchase date at the time warranty service is requested the manufacturing date of the product will be used to determine the warranty period ABOUTYOUR WARRANTY We welcome warranty repair and apologize to you for being inconvenienced Warranty service is available only through SNAPPER PRO Authorized Service Dealers Most warranty repairs are handled routinely but sometimes requests for warranty service may not be appropriate This warranty only covers defects in materials or workmanship It does not cover damage caused by improper use or abuse improper maintenance or repair normal wear and tear or stale or unapproved fuel Improper Use and Abuse The proper intended use of this product is desc
66. o adjust If the machine creeps forward turn the rod CLOCKWISE while standing at the rear of the machine facing forward if the machine creeps backward turn the rod COUNTERCLOCKWISE 3 Lock the nuts B against the ball joints when neutral is achieved NOTE This adjustment should not be performed while the machine is running It may take several attempts to achieved neutral depending upon how much the machine creeps Parking Brake Adjustment 1 Disengage the PTO stop the engine block the front wheels remove the ignition key and engage the parking brake 2 Locate the brake spring A Figure 35 S N 2014161188 8 Below 3 With the parking brake engaged measure the compressed spring length The spring should be 2 3 8 6 0 cm when compressed CAUTION Do not adjust the spring to be shorter than 2 5 16 5 9 cm when compressed This may damage the brake mechanism 4 If the spring is not within this range release the parking brake and turn the adjustment nut B to compress or release the spring 5 Engage the parking brake and remeasure the spring S N 2014161189 amp Above 3 With the parking brake engaged measure the compressed spring length The spring should be 2 3 4 7 cm when compressed 4 If the spring length does not equal the measurement the spring length will need to be adjusted 5 Disengage the parking brake 6 Loosen the set collar C and slide it away from the back
67. o wipe fittings and surfaces clean both before and after lubrication Lubricating the Front Casters NOTE Front casters should be lubricated annually 1 Remove the 1 4 28 bolt A Figure 23 screwed into the front caster and install a 1 4 28 grease fitting 2 Grease the front caster 3 Remove the 1 4 28 grease fitting and reinstall the 1 4 28 bolt 4 Repeat process for the other side of the machine Regular Maintenance Figure 23 Front Caster amp Wheel A 1 4 28 Bolt 27 Regular Maintenance Check Hydraulic Oil Level Oil Type 20W 50 conventional detergent motor oil 1 Check the oil level when the unit is cold The oil should be up to the FULL COLD mark on the transmission oil reservoirs A Figure 24 If the oil is below this level proceed to step 2 2 Before removing the reservoir cap make sure the area around the reservoir cap and fill neck of the reservoir is free of dust dirt and other debris Remove the reservoir caps 3 Add oil up to the FULL COLD mark 4 Reinstall the reservoir cap Change Hydraulic Oil Filter Change Interval Every 400 Hours Initial hydraulic oil and filter change after first 100 hours of operation Filter Part Number 5101978X2 NOTE Removing the oil filter from the transmission will drain the oil reservoir Have a suitable container ready to catch any spilled oil The manufacturer recommends this be a d
68. orrectly Tires are not properly inflated Blades are damaged Deck shell is damaged Mower spindle is bent or loose Blades are installed incorrectly aon ULN Level the deck correctly Check and inflate the tires Replace the blades Repair or replace the deck Repair or replace the spindle Reinstall the blades correctly o JO Ot BWDP Deck is not leveled correctly Blades are dull or worn Blades are damaged Deck is clogged with grass clippings Deck shell is damaged Mower spindle is bent or loose Blades are installed incorrectly Tires are not properly inflated ON OO BR WDM Level the deck correctly Sharpen or replace the blades Replace the blades Clean out the deck Repair or replace the deck Repair or replace the spindle Reinstall the blades correctly Check and inflate the tires Stingers 46 o C rS Blades are not sharp or nicked Blades are worn down too far Engine speed is too low Ground speed is too fast Deck is plugged with grass OQ won Sharpen your blades Replace your blades Always mow at full throttle Slow down Clean out the mower www SnapperPro com Specifications NOTE Specifications are correct at time of printing and are subject to change without notice ENGINE 26 Gross HP T Kawasaki Product Model 5900937 Make Kawasaki Model
69. ory B 500 hours Category A 1000 hours SNAPPER BRIGGS amp STRATTON POWER PRODUCTS GROUP LLC 5375 NORTH MAIN STREET MUNNSVILLE NY 13409 800 933 6175 Operators Manual S200XT Series Zero Turn Riding Mowers
70. owner Any such part repaired or replaced under warranty will be warranted for the remainder of the period prior to the first scheduled replacement point for the part Add on or modified parts that are not exempted by the Air Resources Board may not be used The use of any non exempted add on or modified parts by the owner will be grounds for disallowing a warranty claim The manufacturer will not be liable to warrant failures of warranted parts caused by the use of a non exempted add on or modified part 3 Consequential Coverage Coverage shall extend to the failure of any engine components caused by the failure of any warranted emissions parts 4 Claims and Coverage Exclusions Warranty claims shall be filed according to the provisions of the B amp S engine warranty policy Warranty coverage does not apply to failures of emissions parts that are not original equipment B amp S parts or to parts that fail due to abuse neglect or improper maintenance as set forth in the B amp S engine warranty policy B amp S is not liable for warranty coverage of failures of emissions parts caused by the use of add on or modified parts Look For Relevant Emissions Durability Period and Air Index Information On Your Small Off Road Engine Emissions Label Engines that are certified to meet the California Air Resources Board CARB small off road Emissions Standard must display information regarding the Emissions Durability Period and the Air Index Briggs
71. perienced with operating the Zero Turn rider you will learn more maneuvers that will make your mowing time easier and more enjoyable Remember the more you practice the better your control of the Zero Turn will be Figure 14 Executing an End Of Row Turn 21 Operation Mowing 1 Engage the parking brake Make sure the PTO switch is disengaged the motion control levers are locked in the NEUTRAL position and the operator is on the seat Start the engine see Starting The Engine 3 Set the mower cutting height see Mowing Height Adjustment Set the throttle to FULL Engage the PTO by pulling up on the PTO switch Begin mowing When finished shut off the PTO by pushing the PTO switch down completely 8 Stop the engine see Stopping The Rider and Engine Po NOOO Mowing Recommendations Several factors can affect how well your machine cuts grass Following proper mowing recommendations can improve the performance and life of your machine Height of Grass Often cutting height is a matter of personal preference Typically you should mow the grass when it is is between three and five inches high The proper cutting height range for a specific lawn will depend upon several factors including the type of grass the amount of rainfall the prevailing temperature and the lawn s overall condition Cutting the grass too short causes weak thin gras
72. position 2 NOTE A warm engine may not require choking Set the engine throttle control to FULL throttle position Then fully close the choke by pulling the knob OUT fully 3 Insert the key into the ignition switch and turn it to START 4 After the engine starts gradually open the choke push knob down fully Reduce to half throttle speed and allow to warm up Warm up the engine by running it for at least a minute before engaging the PTO switch or driving the rider 5 After warming the engine ALWAYS operate the unit at FULL THROTTLE when mowing In the event of an emergency the engine can be stopped by simply turning the ignition switch to STOP Use this method only in emergency situations For normal engine shut down follow the procedure given in STOPPING THE RIDER Stopping the Rider 1 Returning the ground speed control levers to the middle position will stop rider movement Pivot the levers outward and lock them in NEUTRAL 2 Disengage the PTO by pushing down on the PTO switch 3 Engage the parking brake by pulling the handle up until it locks into position 4 Move the throttle control to mid throttle position and turn the ignition key to OFF Remove the key Operation Pushing the Rider By Hand NOTICE DO NOT TOW RIDER Towing the units will cause hydraulic transaxle and wheel motor damage Do not use another vehicle to push or pull this unit 1 Disengage the PTO engage the parking brake
73. power equipment This difference is due to a variety of factors including but not limited to the variety of engine components air cleaner exhaust charging cooling carburetor fuel pump etc application limitations ambient operating conditions temperature humidity altitude and engine to engine variability Due to manufacturing and capacity limitations Briggs amp Stratton may substitute an engine of higher rated power for this Series engine CHASSIS Fuel Tank Capacity 12 Gallons 45 4 L Dual Tank Models 6 Gallons 22 7 L Single Tank Model Rear Wheels Tire Size 24 x 12 00 12 Inflation Pressure 15 psi 1 03 bar Front Wheels Tire Size 13 x 6 50 6 Inflation Pressure N A Inflation Pressure 25 psi 1 72 bar Models w Flat Free Tires Models w Air Filled Tires TRANSMISSIONS HydroGear ZT 5400 Powertrain Type Intergrated Transmission Hydraulic Fluid SAE 20W 50 motor oil Speeds Forward 0 10 MPH 0 16 09 km h 3400 rpm Reverse 0 5 MPH 0 8 05 km h 61 Models 72 Models Overall Length 79 201 cm 82 208 cm Overall Width 63 160 cm 73 5 187 cm deflector up Overall Width 76 193 cm 88 224 cm deflector down Height 68 173 cm 1175 lbs 534 kg 1351 lbs 613 kg 47 Iy ay JO lBue y YLM PIO ay Jo a Bue ay 1eduuoo aunjyonij s e9n1an Aue 10 qsod 5u e ajod aul 4amod e 994 891194 e YUM
74. r holes ruts or bumps Uneven terrain could overturn the unit Tall grass can hide obstacles 4 Use slow speed Choose a slow speed so that you will not have to stop or change speed while on the slope This limit was determined per CEN Standard EN 836 1997 Section 5 2 2 and is based on the EN 836 Stability Test procedure described in Section 4 2 4 2 The 15 degree limit of stability is equal to 50 of the angle at which machine lift off occurred in static tests Actual dynamic stability may vary depending on operating conditions 5 Operator Safety Use extra care with grass catchers or other attachments These can change the stability of the unit Keep all movement on the slopes slow and gradual Do not make sudden changes in speed or direction See your authorized dealer for recommendations of available weights to improve stability ae Not OND Oo Avoid starting stopping or turning on a slope If tires lose traction i e machine stops forward motion on a slope disengage the blade s PTO and drive slow off the slope Do not turn on slopes unless necessary and then turn slowly and gradually uphill if possible Never mow down slopes Do not mow near drop offs ditches or embankments The operator could lose footing or balance or mower could suddenly turn over if a wheel is over the edge of a cliff or ditch or if an edge caves in Do not mow on wet grass Reduced footing or
75. r to engine manual for fuel recommendations e Make sure all nuts bolts screws and pins are in place and tight e Dual Fuel Tank Models Make sure the fuel valve is in the ON position e Check the tire pressures See Check Tire Pressures e Make sure that the Roll Bar is adjusted in the upright position See Raise and Lower the Roll Bar e Adjust the seat position and make certain you can reach all controls from operator s position See Seat Adjustment e Adjust the height of the mower deck to the desired position See Mowing Height Adjustment www SnapperPro com Check Tire Pressures Tire pressure should be checked periodically and maintained at the levels shown in the chart Note that these pressures may differ slightly from the Max Inflation stamped on the side wall of the tires The pressures shown provide proper traction improve cut quality and extend tire life Seat Adjustment See Figure 4 The seat can be adjusted forward and backward Move the lever towards the left position the seat as desired and release the lever to lock the seat into position Mowing Height Adjustment The cutting height adjustment pin A Figure 5 control the mower cutting height The cutting height is adjustable between 1 1 2 3 8 cm and 6 15 2 cm in 1 4 0 64 cm increments 1 Depress the deck lift foot pedal B until it locks into the 6 15 2 cm position 2 Place the cutting height adjustment pin in
76. ribed in the Operator s Manual Using the product in a way not described in the Operator s Manual or using the product after it has been damaged will void your warranty Warranty is not allowed if the serial number on the product has been removed or the product has been altered or modified in any way or if the product has evidence of abuse such as impact damage or water chemical corrosion damage Improper Maintenance or Repair This product must be maintained according to the procedures and schedules provided in the Operator s Manual and serviced or repaired using genuine Briggs amp Stratton parts or equivalent Damage caused by lack of maintenance or use of non original parts is not covered by warranty Normal Wear Like all mechanical devices your unit is subject to wear even when properly maintained This warranty does not cover repairs when normal use has exhausted the life of a part or the equipment Except as noted in the warranty period maintenance and wear items such as filters belts cutting blades and brake pads except engine brake pads are not covered by warranty due to wear characteristics alone unless the cause is due to defects in material or workmanship Stale Fuel In order to function correctly this product requires fresh fuel that conforms to the criteria specified in the Operators Manual Damage caused by stale fuel carburetor leaks clogged fuel tubes sticking valves etc is not covered by warranty Other Exclusions
77. s 46 SPOGCINGATIONS 47 Slope Identification Guide 48 NOTE In this manual left and right are referred to as seen from the operating position Operator Safety Read the Manual The operator s manual contains important safety information you need to be aware of BEFORE you operate your unit as well as DURING operation Safe operating techniques an explanation of the product s features and controls and maintenance information is included to help you get the most out of your equipment investment Be sure to completely read the Safety Rules and Information found on the following pages Also completely read the Operation section Operating Safety Congratulations on purchasing a superior quality piece of lawn and garden equipment Our products are designed and manufactured to meet or exceed all industry standards for safety Do not operate this machine unless you have been trained Reading and understanding this operator s manual is a way to train yourself Power equipment is only as safe as the operator If it is misused or not properly maintained it can be dangerous Remember you are responsible for your safety and that of those around you Use common sense and think through what you are doing If you are not sure that the task you are about to perform can be safely done with the equipment you have
78. s plants which are easily damaged by dry periods and pests Cutting too short is often more damaging than allowing the grass to be slightly higher Letting grass grow a bit longer especially when it is hot and dry reduces heat build up preserves needed moisture and protects the grass from heat damage and other problems However allowing grass to grow too high can cause thin turf and additional problems Cutting off too much at one time shocks the plant s growth system and weakens the grass plants A good rule of thumb is the 1 3 rule to cut no more than one third of the grass height and never more than 1 inch at a time The amount of grass you are able to cut in one pass is also effected by the type of mowing system you are using for example broadcasting with side discharge decks can process a much larger volume of grass than mulching does 22 rit M al ES ileal dud gt AIDA Figure 15 Proper Cutting Height Tall Grass Requires Incremental Cutting For extremely tall grass set the cutting height at maximum for the first pass and then reset it to the desired height and mow a second or third time Don t cover the grass surface with a heavy layer of clippings Consider using a grass collection system and starting a compost pile Cut Here On First Pass Cut Here On Second Pass JAVI AMA Figure 16 Incremental Cutting www SnapperPro com When and How Otten to Mow
79. sition prevent accidental starting of the engine Remedy 1 Engage parking brake 2 Place in OFF position 3 If engine is hot allow it to cool then refill the fuel tank 4 Move choke control to closed position 5 Replace fuse 6 Clean the battery terminals 7 Recharge or replace 8 Visually check wiring amp replace broken or frayed wires Tighten loose connections 9 Repair or replace See authorized dealer 10 Replace as needed See authorized service dealer 11 Clean and gap or replace See engine manual 12 Drain fuel amp replace with fresh fuel 13 Drain fuel amp replace with fresh fuel k Clean air filter Check choke adjustment Clean and gap or replace See engine manual N i Check add oil as required See engine manual N Clean engine fins blower screen and air cleaner See engine manual Drain excess oil Replace air filter See engine manual Open choke control n op www SnapperPro com Rider Troubleshooting Continued Problem Engine runs but rider will not drive Rider drive belt slips Brake will not hold Rider steers or handles poorly Troubleshooting the Mower Problem Mower will not raise Engine stalls easily with mower engaged Excessive mower vibration Excessive belt wear or breakage Mower drive belt slips or fails to drive Mower does not engage Cause 1 Hydraulic release valve s
80. th over vent caps on both batteries 4 Connect positive cable to positive post of discharged battery wired to starter or solenoid 5 Connect the other end of same cable to same post marked positive on booster battery 6 Connect the second cable negative to other post of booster battery 7 Make final connection on engine block of stalled vehicle away from battery Do not lean over batteries 8 Start the engine of the vehicle with the booster battery Wait a few minutes then attempt to start the engine of the vehicle with the discharged battery 9 If the vehicle does not start after cranking for thirty seconds STOP PROCEDURE More than thirty seconds seldom starts the engine unless some mechanical adjustment is made 10 After starting allow the engine to return to idle speed Remove the cable connection at the engine or frame Then remove the other end of the same cable from the booster battery 11 Remove the other cable by disconnecting at the discharged battery first and then disconnect the opposite end from the booster battery 12 Discard the damp cloths that were placed over the battery vent caps 41 Regular Maintenance THIS HOOK UP FOR NEGATIVE GROUND VEHICLES To Switch To Starter Switch Jumper Cable Starting Vehicle Battery To Ground Discharged Vehicle Battery MAKE CERTAIN VEHICLES DO NOT TOUCH Figure 53 Jump Starting A WARNING Any procedure other than th
81. the unit Before leaving the operator s position for any reason engage the parking brake disengage the PTO stop the engine and remove the key To reduce fire hazard keep the engine tractor and mower free of grass leaves and excess grease Do not stop or park tractor over dry leaves grass or combustible materials Gasoline is highly flammable and must be handled with care Never fill the tank when the engine is still hot from recent operation Do not allow open flame smoking or matches in the area Avoid over filling and wipe up any spills WARNING Do not load this zero turn rider on a trailer or truck using two separate ramps Only use a single ramp that is at least one foot wider than the width of the rear wheels of this rider This rider has a zero turning radius and the rear wheels could fall off the ramps or the rider could tip over injuring the operator or bystanders 16 A WARNING Never operate on slopes greater than 15 Select slow ground speed before driving onto a slope Use extra caution when operating on slopes with a rear mounted grass catcher Mow across the face of slopes not up and down use caution when changing directions and DO NOT START OR STOP ON SLOPE Checks Before Starting e Check that crankcase is filled to full mark on dipstick See the engine Operators Manual for instructions dipstick locations and oil recommendations e Fill the fuel tank with fresh fuel Refe
82. they are functioning properly OPERATION iL Never run an engine in an enclosed area 11 12 13 14 15 16 17 18 19 20 2 22 Mow only in the daylight or with good artificial light keeping away from holes and hidden hazards Be sure all drives are in neutral and parking brake is engaged before starting engine Only start engine from the operator s position Use seat belts if provided Be sure of your footing while using pedestrian controlled equipment especially when backing up Walk don t run Reduced footing could cause slipping Slow down and use extra care on hillsides Be sure to travel in the recommended direction on hillsides Turf conditions can affect the machines stability Use caution when operating near drop Offs Do not mow in reverse unless absolutely necessary Always look down and behind before and while traveling in reverse Be aware of the mower discharge direction and do not point it at anyone Do not operate the mower without either the entire grass catcher or the deflector in place Slow down and use caution when making turns and when changing directions on slopes Never raise deck with the blades running Never leave a running unit unattended Always disengage the PTO set parking brake stop engine and remove keys before dismounting Keep hands and feet away from the cutting units Turn off the PTO switch to disengage th
83. ting guide below lists the most common problems their causes and remedies See the information on the following pages for instructions AWARNING To avoid serious injury perform maintenance on the tractor or mower only when the engine is stopped and the parking brake engaged Always remove the ignition key disconnect the spark plug wire and fasten it away from the plug before beginning the maintenance to on how to perform most of these minor adjustments and service repairs yourself If you prefer all of these procedures can be performed for you by your local authorized dealer Troubleshooting the Rider Problem Engine will not turnover or start Engine starts hard or runs poorly Engine knocks Excessive oil consumption Engine exhaust is black 44 Cause 1 2 N Parking brake not engaged PTO electric clutch switch in ON position Out of fuel Engine flooded Fuse blown Battery terminals require cleaning Battery discharged or dead Wiring loose or broken Solenoid or starter motor faulty Safety interlock switch faulty Spark plug s faulty fouled or incorrectly gapped Water in fuel Gas is old or stale Fuel mixture too rich Spark plug faulty fouled or incorrectly gapped Low oil level Using wrong grade oil Engine running too hot Using wrong weight oil Too much oil in crankcase Dirty air filter Engine choke control is in closed po
84. tore the unit indoors or in any other area where fuel vapor could travel to any ignition source Fuel vapor is also toxic if inhaled so never store the unit in any structure used for human or animal habitation Here is a checklist of things to do when storing your unit temporarily or in between uses e Keep the unit in an area away from where children may come into contact with it If there s any chance of unauthorized use remove the spark plug s and put in a safe place Be sure the spark plug opening is protected from foreign objects with a suitable cover e If the unit can t be stored on a reasonable level surface chock the wheels e Clean all grass and dirt from the mower Long Term Storage Longer Than 30 Days Before you store your unit for the off season read the Maintenance and Storage instructions in the Safety Rules section then perform the following steps 1 Drain crankcase oil while engine is hot and refill with a grade of oil that will be required when unit is used again 2 Prepare the mower deck for storage as follows a Remove mower deck from the unit b Clean underside of mower deck c Coat all bare metal surfaces with paint or light coat of oil to prevent rusting 3 Clean external surfaces and engine 4 Prepare engine for storage See engine owner s manual 5 Clean any dirt or grass from cylinder head cooling fins engine housing and air cleaner element 6 Cover air cleaner and exhaust outl
85. turn the ignition OFF and remove the key 2 Open the hydraulic bypass valve To open the bypass valves turn the bypass valve which is located on the side of the transmission CLOCKWISE See Figure 8 for valve location 3 Disengage the parking brake The tractor can now be pushed by hand 4 After moving the tractor re engage the transmissions drive position by turning the bypass valves COUNTER CLOCKWISE Figure 8 Hydraulic System By Pass A Hydraulic Bypass Valve 19 Operation Zero Turn Driving Practice The lever controls of the Zero Turn rider are responsive and learning to gain a smooth and efficient control of the rider s forward reverse and turning movements will take some practice Spending some time going through the maneuvers shown and becoming familiar with how the unit accelerates travels and steers before you begin mowing is absolutely essential to getting the most out of the Zero Turn rider Locate a smooth flat area of your lawn one with plenty of room to maneuver Clear the area of objects people and animals before you begin Operate the unit at mid throttle during this practice session ALWAYS operate at full throttle when mowing and turn slowly to prevent tire slippage and damage to your lawn We suggest you begin with the Smooth Travel procedure to the right and then advance throu
86. ty 2 1 US qt 2 0 L w filter 36 Gross HP Briggs amp Stratton Vanguard Product Models 5900585 amp 5900601 Make Briggs amp Stratton Specifications Model Displacement Electrical System 613777 0116 G1 60 60 Cu In 993 cc 12 volt 20 amp alternator Battery 340 cca Oil Capacity 2 4 US qt 2 3 L w filter tPower Ratings All power levels are stated gross horsepower per SAE J2723 as rated by Kawasaki and tested per the SAE J1995 test standard The gross power curves and more information can be viewed at www kawasaki criticalpower com Power Ratings The gross power rating for individual gas engine models is labeled in accordance with SAE Society of Automotive Engineers code J1940 Small Engine Power amp Torque Rating Procedure and rating performance has been obtained and corrected in accordance with SAE J1995 Revision 2002 05 Torque values are derived at 3060 RPM horsepower values are derived at 3600 RPM The gross power curves can be viewed at www BRIGGSandSTRATTON COM Net power values are taken with exhaust and air cleaner installed whereas gross power values are collected without these attachments Actual gross engine power will be higher than net engine power and is affected by among other things ambient operating conditions and engine to engine variability Given the wide array of products on which engines are placed the gas engine may not develop the rated gross power when used in a given piece of
87. www SnapperPro com Practice Turning Around a Corner While traveling forward allow one handle to gradually return back toward neutral Repeat several times NOTE To prevent pivoting directly on the tire tread it is best to keep both wheels going at least slightly forward Operation Practice Turning In Place To turn in place Zero Turn gradually move one ground speed control lever forward from neutral and one lever back from neutral simultaneously Repeat several times NOTE Changing the amount each lever is pulled forward or back changes the pivot point you turn on Executing Turns Turning In Place Figure 12 Turning Around a Corner Figure 13 Turning in Place Executing an End Of Row Zero Turn Your Zero Turn Rider s unique ability to turn in place allows you to turn around at the end of a cutting row rather than having to stop and Y turn before starting a new row For example to execute a left end of row zero turn 1 Slow down at the end of the row 2 Move the RIGHT ground speed control lever forward slightly while moving the LEFT ground speed control lever back to center and then slightly back from center 3 Begin mowing forward again This technique turns the rider LEFT and slightly overlaps the row just cut eliminating the need to back up and re cut missed grass As you become more familiar and ex
88. y from deck unless discharge chute or entire grass catcher is in its proper place Amputation and Pinch Point Hazard To avoid injury from rotating parts stay clear of parts and keep all shields and guards in place LOW OVERHANGING OBSTACLES HAZARD Check for overhead objects Do NOT allow roll bar to contact low overhanging obstacles such as tree branches and guide wires 3 18461 Avoid serious injury or death from rollover Do not operate without the rollbar installed and operational 5100683 A DANGER PINCH POINT To avoid injury from loaded spring read operator s manual before removing AVOID SERIOUS INJURY OR DEATH FROM ROLL OVER Keep roll bar in the raised position and use seat belt THERE IS NO ROLL OVER PROTECTION WHENTHE ROLL BAR IS DOWN Lower the roll bar only when necessary and NEVER remove it Do NOT use seat belt when the roll bar is down Raise the roll bar as soon as clearance permits Do NOT jump off if mower tips Read and follow all operating instructions and warnings in the operator s manual ROLL OVER PROTECTIVE STRUCTURE To maintain operator protection and roll bar certification Replace a damaged roll bar do NOT attempt to repair or modify Any alteration of the roll bar must be approved by the manufacturer DO NOT exceed the machine weight rating of the roll bar 3 1842
89. y from moving parts If possible do not make adjustments with the engine running Charge batteries in an open well ventilated area away from spark and flames Unplug charger before connecting or disconnecting from battery Wear protective clothes and use insulated tools Grass catcher components are subject to wear damage and deterioration which could expose moving parts or allow objects to be thrown Frequently check components and replace with manufacturer s recommended parts when necessary Check brake operation frequently Adjust and service as required Use only factory authorized replacement parts when making repairs Always comply with factory specifications on all settings and adjustments Only authorized service locations should be utilized for major service and repair requirements Never attempt to make major repairs on this unit unless you have been properly trained Improper service procedures can result in hazardous operation equipment damage and voiding of manufacturer s warranty Units with hydraulic pumps hoses or motors WARNING Hydraulic fluid escaping under pressure may have sufficient force to penetrate skin and cause serious injury If foreign fluid is injected into the skin it must be surgically removed within a few hours by a doctor familiar with this form of injury or gangrene may result Keep body and hands away from pin holes or nozzles that eject hydraulic fluid under high pressure Use paper

Snapper 5900750 Lawn Mower User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents