SMSC EZ Card 10 Network Card User Manual
Contents
1. This guide covers the following topics Product description summary of features and specifications e Description of important hardware features of the cards such as LEDs and connectors Installation procedure Note Procedures for network driver installation and additional information or changes that become available after the manual is printed are in text files which are located on the SMC Installation Diskette You can use the DOS DIR command to locate all the available text files and view their contents using the DOS TYPE command PACKAGE CONTENTS ii Carefully unpack the contents of the package and check them against the checklist below One EZ Card 10 PCI Network Card BNC T Connector combo models only One Driver Diskette This User Guide SMC Warranty Registration Card please complete and return this card to SMC Note Network cards are sensitive to static electricity which can damage their delicate electronic components Dry weather conditions or walking across a carpeted floor may cause you to acquire an electrostatic charge A AB a GS To protect your device always Touch the metal chassis of your computer before you pick up the card This grounds the electrostatic charge Avoid touching any of the electrical components when handling the card If possible wear a grounded wrist strap or anti static gloves Please inform your dealer immediately should there be any incorrect missing2. cccccseeseseesseeesees C 4 Media Py Pe isccsevscshessediesceteviesiasledeneccdesizsh sbecets REEE S see C 5 Full Duplex Mode cccccccessescsscesssseseesesseeseesseeeeessens C 5 Boot ROM SZE 41 35 Scctectvedsciashicieclceuieiavievtanahotaaesiecists C 5 iii TABLE OF CONTENTS Running the DiaQnostics ccccsccsessesssseesseeeeseeesseeseesees C 6 EEPROM T St xi ccieadidanGintatathcuiraravenGnnin ae C 6 Testing the Card a fvsecserssiesdcsseseau nition aeviemesieeresebectes C 6 Testing the Network Connection cccsssecesseseeeeees C 7 Configuring the Card in Older PCI Computers C 8 D GIOSSARY sisssicsssssssssssssssoososssssssesssosssassssssssssssss D 1 Index Limited Warranty Compliances List of Figures Figure 1 1 EZ Card 10 PCI Combo Model eee 1 2 Figure 1 2 LED Indicators seseseeseeseeeresseseserererreseses 1 3 Figure C 1 Main Menu ssssesssserssesesesesssssesesesesesosseseseses C 2 Figure C 2 Current Configuration Display 0 C 3 Figure C 3 Set Up New Configuration Menu C 4 Figure C 4 On Board Diagnostics Display 0 C 6 List of Tables Table B 1 RJ 45 Connector Pin Assignments B 1 Table B 2 AUI Connector Pin Assignments 0 B 2 IV CHAPTER 1 INTRODUCTION SMC s EZ Card 10 PCI family consists of three 32 bit Ethernet network interface cards for PCI computers a twisted pair card with an RJ 45 connector
3. Class B EN55022 1988 CISPR 22 1985 prEN55024 2 1990 IE801 2 1991 prEN55024 3 1991 IE801 3 1984 prEN55024 4 1992 IE801 4 1988 EN60950 CE marking SPECIFICATIONS Network Drivers ODI drivers NetWare 3 x 4 x NetWare LAN WorkPlace TCP IP Novell LAN Analyzer for NetWare NDIS 2 drivers Microsoft LAN Manager V2 x Windows for Workgroups IBM LAN Server LAN Support IBM OS 2 EE V2 0 DEC PATHWORKS Lantastic 6 0 Sun PC NFS Banyan VINES IBM TCP IP for DOS amp OS 2 Wollongong Pathway Access NDIS 3 drivers Microsoft Windows NT 3 51 4 0 Windows for Workgroups Windows 95 Packet drivers FTP TCP IP NCSA TCP IP Unix drivers SCO OpenServer 5 x A 3 APPENDIX B PIN ASSIGNMENTS RJ 45 Connector Pin Number Output Transmit Data Output Transmit Data 2 3 Input Receive Data 6 Input Receive Data 4 5 7 8 Reserved for other use Table B 1 RJ 45 Connector Pin Assignments B 1 PIN ASSIGNMENTS AUI Connector Circuit 10 M 5 12 4 2 1 13 Voltage Shield P Protective Ground Conductive Shell Table B 2 AUI Connector Pin Assignments G Note Voltage Plus VP and Voltage Common Vc use a single twisted pair in the AUI cable B 2 APPENDIX C CONFIGURATION AND DIAGNOSTICS The driver diskette contains the Setup program SETUP EXE This program allows you to View the current configuration of the card Setup a new configuration Run diagnostics T
4. chosen RJ 45 connector for twisted pair cable BNC connector for thin coax cable e AUI connector for thick coax cable On the 2 port combo model the media type in use is automati cally detected by the driver 1 2 INTRODUCTION LED Indicators The cards contain two LEDs for monitoring network conditions The function of each LED is described below Refer to the fol lowing figure for the LED location a x gt G 4 Activity O O Link gt eo000000 e0000000 Figure 1 2 LED Indicators Link Status Lk Color Green Function Twisted pair link status indicator When lit this LED indicates an active connection between the network card and a 10BASE T hub or switch Note The Link Status LED does not monitor the condition of the BNC and AUI connections When the card is con figured for these connections this LED is always lit 1 3 INTRODUCTION Activity Status ACT Color Green Function Network activity indicator 1 4 This LED is unlit upon power on It lights up to indicate the presence of network activity on the port The rate of flashing is proportional to the amount of network traffic CHAPTER 2 INSTALLING THE CARD The procedure for installing the EZ Card 10 PCI models appears below Although instructions for installing the software drivers are not included here some related information is provided 1 Power off your PC and remove its cover Ple
5. of the Ethernet controller T O Registers Test checks I O accessibility Internal Loop Back Test checks the card s controller External Loop Back Test checks the network link RAM Test checks the condition of the on board RAM The screen displays the PASSED or FAILED count for each test If a test fails press the spacebar to display the reason for the failure and possible solutions Testing the Network Connection This test verifies the card s ability to communicate with other devices on the network At the start of the test set up one com puter as a Responder and at least one as an Initiator The Responder displays the status of communications with each Initiator on the network while the Initiator displays the current Responder and the status of corresponding communications Note Should any of these tests fail reboot your computer and run the diagnostics again to see if the problem persists C 7 CONFIGURATION AND DIAGNOSTICS Configuring the Card in Older PCI Computers C 8 The card is configured using the host PCI computer s BIOS setup program This is done by changing the computer s BIOS settings The procedure to do this and the terminology used depend on the the BIOS you are using For example if your computer uses the Phoenix BIOS there is a Device Select field where you are to input the number of the PCI slot where the adapter is installed e g Slot 3 Device Select Enabled fo
6. or damaged parts If possible retain the carton including the original packing materials Use them again to repack the product in case there is a need to return it for repair Back up your driver diskette and use the copy as the working diskette Do this to protect the original from accidental damage TABLE OF CONTENTS Chapter 1 2 Introduction eessesosssossesosssosseessesosssesseessssos l 1 FEAM TOS eeror ion taen EEEO AAN AEE ENTERA 1 1 Hardware Description ssssesessssssssesesesesssessesesesesrsseseseseses 1 2 TAN CONNECT nisaran naa E 1 2 DED MdicatTS isnin n u a Hens a A aaa 1 3 Unk Status LE n a a aria a 1 3 Activity Status ACT vasencnaciineni aiin i 1 4 Installing the Card cccssssssssssccsssssssenns 2 1 Appendices A Specifications eeessssseeececeeccccccccccceceeceeessessse A 1 Generalen ii eE E A T inne A 1 Operating ENVirOnMent areren aiaia A 2 EMI Safety Compliances ccccssscssessesssccecsscsecseesseeeesees A 2 Network DTiVerS esssssesssseesesesesesessesesesesesersesssesesessssessesese A 3 Pin Assigaments sssssesssssssssssooocessssssssssoe B L RFA COMNCCUOR eoe EEr ESE T REENER SEEE B 1 AUT CONneCtOT niee e A B 2 Configuration and Diagnostics C 1 Running the Setup Program sssssssssesesssssessisesesesesreseseseses C 2 Viewing the Current Configuration sssssesesesseesssseresesss C 3 Setting Up a New Configuration
7. ARY BNC Connector with a half twist locking shell typically used for thin coax cable Boot ROM Read only memory chip that allows a workstation to communi cate with a file server and to read a DOS boot program from the server Bus Topology Network topological arrangement where only one path exists between any two nodes and data transmitted by any node is concurrently available to all other nodes on the same transmis sion medium Driver Program that enables the network operating system to commu nicate with LAN cards TIEFE 802 3 Standard Standard developed by the IEFE Institute of Electrical and Electronics Engineers for physical and electrical connections in local area networks Interrupt IRQ Signal that temporarily suspends a program when input or out put is required and transfers control to the operating system LED Light emitting diode Mbps Megabits per second RJ 45 connector Most common terminator for twisted pair cable D 1 GLOSSARY D 2 Star Topology Also known as hub topology topology where wires run between network nodes and a central wiring hub usually located in the building s wiring closet 10BASE T IEEE specifications for 10 Mbps Ethemet on twisted pair cable 100 Q UTP The maximum cable length for a point to point connection is 100 m 328 ft and the maximum number of nodes is 1024 10BASE2 IEEE specifications for 10 Mbps Ethernet on thin coax cable 50 Q RG 58 A cable segmen
8. EZ Card 10 10 M bps Ethernet PC Network C ards Plug and Play installation NE2000 compatible On board socket for optional boot ROM Support for full duplex Ethernet SMC U ser G uide USER GUIDE FOR SMC s EZ Carp 10 PCI NETWORK CARD September 1997 Pub 79 000559 000 Standard Microsystems Corporation 80 Arkay Drive Hauppauge New York 11788 Information furnished by SMC is believed to be accurate and reliable However no responsibility is assumed by SMC for its use nor for any infringements of patents or other rights of third parties which may result from its use No license is granted by implication or otherwise under any patent or patent rights of SMC SMC reserves the right to change specifications at any time without notice Copyright 1997 by Standard Microsystems Corporation Hauppauge New York All rights reserved Printed in U S A Trademarks SMC is a registered trademark and EZ Card and EliteFax are trademarks of Standard Microsystems Corporation Other product and company names are trademarks or regis tered trademarks of their respective holders ABOUT THIS GUIDE This installation guide is for SMC s family of EZ Card 10 PCI network cards The three models are as follows Order Number Description SMC1208T twisted pair card with RJ 45 connector SMC1208BT 2 port combo card with RJ 45 and BNC connectors SMC1208BTA 3 port combo card with RJ 45 BNC and AUI connectors
9. F LAW STATUTORY OR OTHERWISE INCLUDING WARRANTIES OR CONDITIONS OF MERCHANT ABILITY AND FITNESS FOR A PARTICULAR PURPOSE SMC NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE INSTALLATION MAIN TENANCE OR USE OF ITS PRODUCTS SMC SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMER S OR ANY THIRD PERSON S MISUSE NEGLECT IMPROPER INSTALLATION OR TESTING UNAUTHORIZED ATTEMPTS TO REPAIR OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE OR BY ACCIDENT FIRE LIGHTNING OR OTHER HAZARD LIMITATION OF LIABILITY IN NO EVENT WHETHER BASED IN CONTRACT ORTORT INCLUDING NEGLIGENCE SHALL SMC BE LIABLE FOR INCIDEN TAL CONSEQUENTIAL INDIRECT SPECIAL OR PUNITIVE DAMAGES OF ANY KIND OR FOR LOSS OF REVENUE LOSS OF BUSINESS OR OTHER FINANCIAL LOSS ARISING OUT OF ORIN CONNECTION WITH THE SALE INSTALLATION MAINTENANCE USE PERFORMANCE FAILURE OR INTER RUPTION OF ITS PRODUCTS EVEN IF SMC ORITS AUTHORIZED RESELLER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES NOTHING HEREIN SHALL HAVE THE EFFECT OF LIMITING OR EXCLUDING SMC S LIABILITY FOR DEATH OR PERSONAL INJURY CAUSED BY NEGLIGENCE Some states do not allow the exclusion of implied warranties or the limitation of incidental or consequential damages for consumer products so the above limitations and exclus
10. S ELS HEEORAChACERBHV EF WRAL AS tio TELV RO R ELTV Australia AS NZS 3548 1992 SMC contact for products in Australia is SMC Australia Pty Ltd ACN 069 351 613 LVL 66 MLC Center Martin Place Sydney NSW 2000 Phone 61 2 9238 2206 Fax 61 2 9238 2220 FOR TECHNICAL SUPPORT CALL From U S A and Canada 8 30 AM 8 00 PM Eastern Time 800 SM C 4 YOU 516 435 6250 516 434 9314 Fax From Europe 8 00 AM 5 30 PM UK Greenwich M ean Time 44 0 1344 420068 44 0 1344 418835 Fax Bulletin Board Services BBS M odem settings 9600 8 n 1 New York 516 434 3162 connect speed up to 14 400 Germany 49 0 89 92861 240 France 33 1 39 73 57 00 United Kingdom 44 0 1344 418838 INTERNET address is techsupport smc com Driver updates available from the Internet Host name info smc com IP address 170 129 51 1 SMC Forumon CompuServe at the prompt type GO SMC World Wide Web http www smc com FOR LITERATURE OR ADVERTISING RESPONSE CALL U S A and C anada 800 SMC 4 YOU Fax 516 273 1803 _ New York 516 435 6000 Fax 516 273 1803 Latin America 630 916 7007 630 916 6304 France 33 1 30 87 42 42 Fax 33 1 30 61 41 34 Europe 44 0 1344 418800 Fax 44 0 1344 418828 Northern Europe 44 0 1344 418820 Fax 44 0 1344 418826 Central Europe 49 0 89 92861 0 Fax 49 0 89 92861 230 Eastern Europe M iddle East 49 0 89 92861 142 Fax 49 0 89 9101934 Au
11. and two combo models One of the combo models has two connectors RJ 45 and BNC The other combo model has three connectors RJ 45 BNC and AUI The RJ 45 connector is used for unshielded twisted pair cable the BNC for thin coax cable and the AUI for thick coax cable Features Conforms to the Ethernet IEEE 802 3 standard Compatible with PCI Local Bus specification Revision 2 0 and later Provides 32 bit data transfer to maximize throughput and optimize CPU utilization Software compatible with NE2000 driver Supports full duplex operation for twice the effective band width in a switched network Automatic configuration setup using the PCI computer s BIOS setup program Automatic detection of twisted pair or thin coax media type connection 2 port combo model only Supports optional boot ROM for remote booting from a NetWare server LED indicators for monitoring network traffic 1 1 INTRODUCTION Hardware Description The SMC EZ Card 10 PCI model shown below has two LED indicators and supports three types of network connections Your model may support only one or two network connections RJ 45 Connector LED Indicators BNC Connector Lt AUI ae Connector Figure 1 1 EZ Card 10 PCI Combo Model SMC1208BTA LAN Connectors The EZ Card 10 PCI models support IEEE 802 3 10BASE T 10BASE2 and 10BASE5 standards These cards also support one or more of the following network connections depending on the model
12. ase refer to your computer s Installation Manual for instructions on how to remove the cover 2 Select an available expansion slot and plug in the card The card provides a 32 bit bus interface It plugs into any available PCI expansion bus slot Remove the protector bracket from the slot you selected Insert the card into the slot Carefully press on the card until all the edge connec tors are firmly in place inside the slot Screw the card s steel bracket into the PC to secure the connection Replace the PC cover 3 Connect your card to the network Select a cable type for your application and attach the card to the network using the appropriate connector RjJ 45 for twisted pair cable BNC for thin coax cable e AUI for thick coax cable 2 1 INSTALLING THE CARD 2 2 4 Power on the PC Hardware installation has been completed Switch on power to the PC Note Your network should be configured automatically by the PCI computer s BIOS Setup Program However some manual configuration may be required in older PCI machines Refer to Configuring the Card in Older PCI Computers in Appendix C for related information Run the Diagnostic program to check the card s hard ware installation For related topics see Running the Setup Program in Appendix C Caution Be sure to run this program before installing the appropriate driver Otherwise your PC will hang Install the driver The driver di
13. figuration go back to the Main Menu and choose SET UP NEW CONFIGURATION Press Space Bar to continue Figure C 2 Current Configuration Display C 3 CONFIGURATION AND DIAGNOSTICS Setting Up a New Configuration If your computer complies with PCI BIOS standards the system will automatically allocate the necessary I O IRQ and boot ROM address resources to the card Although the SETUP program will not allow you to change the resources which are allocated by the PCI BIOS it will allow you to change the following settings to suit your requirements e Media type e Full duplex mode e Boot ROM size SMC1208 PCI Adapter Setup And Diagnostics Version V1 00 1995 Set Up New Configuration Menu Full duplex Boot ROM Size Disabled Choose MEDIUM TYPE option to select a medium type Previous Esc Select ty Figure C 3 Set Up New Configuration Menu C 4 CONFIGURATION AND DIAGNOSTICS Media Type The transceiver setting should agree with the network cabling type The program provides two choices e Auto detection 10BASE5 AUI With the first choice the card automatically detects the connec tor in use either RJ 45 or BNC The second choice enables the AUI connector Full Duplex Mode Enable full duplex mode only if the card is connected directly to a switch that also supports this mode Do not enable this mode if the card is connected to a hub Boot ROM Size Each card provides an empty socket fo
14. hese tasks are described in this chapter C 1 CONFIGURATION AND DIAGNOSTICS Running the Setup Program Insert the driver diskette in your floppy drive The SETUP pro gram is in the SETUP subdirectory on this diskette Change to the appropriate subdirectory location type the following com mand and press lt Enter gt A SETUP gt SETUP This will initiate the menu driven SETUP program and display the Main Menu as shown below SMC1208 PCI Adapter Setup And Diagnostics Version V1 00 1995 Set Up New Configuration Run EEPROM Test Run Diagnostic On Board Run Diagnostic On Network Exit SETUP Choose VIEW CURRENT CONFIGURATION to look at the adapter s configuration Help Fl Exit Esc Select ty Accept Figure C 1 Main Menu C 2 CONFIGURATION AND DIAGNOSTICS Viewing the Current Configuration Select this option to view the current settings for your network card as shown below If you need to modify the current configuration return to the Main Menu and select Set Up New Configuration SMC1208 PCI Adapter Setup And Diagnostics Version V1 00 1995 Current Configuration Ethernet Address 00 00 E8 D7 79 39 Medium Type Auto Detect Full duplex Disabled I O Base FF80 H Interrupt 10 Boot ROM Size Disabled This is your PCI LAN Adapter current configuration If this is the configuration you want to use go back to the Main Menu and choose EXIT SETUP On the other hand if you want to change the con
15. ions may not apply to you This warranty gives you spe cific legal rights which may vary from state to state Nothing in this warranty shall be taken to affect your statutory rights Standard Microsystems Corporation 80 Arkay Drive Hauppauge NY 11788 516 273 3100 COMPLIANCES FCC Class B This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with instructions may cause harmful interference to radio communications However there is no guarantee that the interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television recep tion which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Shielded twisted pair cable is required for Class B compliance If unshielded twisted pair cable is used
16. orrected For any third party products listed in the SMC software product documentation or specifications as being compatible SMC will make reasonable efforts to prove compatibility except where the non compatibility is caused by a bug or defect in the third party s product STANDARD WARRANTY SERVICE Standard warranty service for hardware products may be obtained by delivering the defective product accompanied by a copy of the dated proof of purchase to SMC s Service Center or to an Authorized SMC Service Center during the applicable warranty period Standard warranty service for software products may be obtained by telephoning SMC s Service Center or an Authorized SMC Service Center within the warranty period Products returned to SMC s Service Center must be pre authorized by LIMITED WARRANTY SMC with a Return Material Authorization RMA number marked on the out side of the package and sent prepaid insured and packaged appropriately for safe shipment The repaired or replaced item will be shipped to Customer at SMC s expense not later than thirty 30 days after receipt by SMC WARRANTIES EXCLUSIVE IF AN SMC PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE CUSTOMER S SOLE REMEDY SHALL BE REPAIR REPLACEMENT OR REFUND OF THE PURCHASE PRICE PAID AT SMC S OPTION THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES OR CONDITIONS EXPRESS OR IMPLIED EITHER IN FACT OR BY OPERATION O
17. property of SMC Replacement products may be new or reconditioned Any replaced or repaired product or part has a ninety 90 day warranty or the remainder of the initial warranty period whichever is longer SMC shall not be responsible for any custom software or firmware configura tion information or memory data of Customer contained in stored on or integrated with any products returned to SMC pursuant to any warranty SOFTWARE SMC warrants that the software programs licensed from it will perform in substantial conformance to the program specifications for a period of ninety 90 days from the date of purchase from SMC or its Authorized Reseller SMC warrants the magnetic media containing software against failure during the warranty period No updates are provided SMC s sole obligation hereunder shall be at SMC s discretion to refund the purchase price paid by Customer for any defective software products or to replace any defective media with software which substantially conforms to SMC s applicable published spec ifications Customer assumes responsibility for the selection of the appropriate applications program and associated reference materials SMC makes no war ranty that its software products will work in combination with any hardware or applications software products provided by third parties that the operation of the software products will be uninterrupted or error free or that all defects in the software products will be c
18. r an optional 16 KB boot ROM Once installed and enabled the boot ROM permits the host PC to download the disk operating system DOS or network drivers over the network The boot ROM function is disabled by default After you install a boot ROM be sure to enable this function C 5 CONFIGURATION AND DIAGNOSTICS Running the Diagnostics To test the card s components and installation the SETUP pro gram runs three different tests on the card and corresponding cabling system as listed below e EEPROM Test Diagnostics on Board Diagnostics on Network Note Run the diagnostics before the network driver is loaded into the system Otherwise your system may hang EEPROM Test Read tests are performed on each register in the EEPROM Testing the Card This test monitors the card and corresponding cabling system However it does not test the network s condition SMC1208 PCI Adapter Setup And Diagnostics Version V1 00 1995 Node ID 00 00 EB D7 79 39 Medium Type Auto Detect I O Base FF80 H Interrupt 10 Full duplex Enabled 381 0 1 configuration Test 2 1 0 Registers Test 381 3 Internal Loop Back Test 380 4 External Loop Back Test 380 380 F1 Help Esc Exit Space Bar Help for LAN Adapter Failure Figure C 4 On Board Diagnostics Display C 6 CONFIGURATION AND DIAGNOSTICS This test actually performs five separate tests Configuration Test checks the initial status
19. r the Enable Device field and assign an IRQ number the card s IRQ setting is mapped to the BIOS IRQ setup of the host PCI computer Set the Trigger Routing field to select the Trigger method by which the IRQ is assigned or routed to the PCI slot There are three types of settings to choose from e Level Auto This is usually the default Choosing this option leaves the assigned IRQ free for other uses if the installed card does not use it Level Forced If you are not able get the PCI card to work properly choose this option This will assign the spec ified IRQ permanently to the card Edge Auto Some PCI cards support this option Do not use it with SMC s EZ Card 10 PCI models Notes These PCI cards can only function with the EMM386 exe memory manager program version 4 49 or later You can verify the version number by entering EMM386 at the DOS prompt Do not specify the HIGHSCAN option with the EMM386 exe statement in your config sys file or your system will hang If you run MEMMAKER and select Custom Setup do not specify Aggressively scan upper memory or it will CONFIGURATION AND DIAGNOSTICS automatically insert the HIGHSCAN flag into the EMM386 command line This parameter cannot be manually removed once it is installed doing so will cause the extended memory manager to malfunction For problems with your BIOS setup refer to your PC s user documentation C 9 APPENDIX D GLOSS
20. skette contains all the driver programs supported by these cards Refer to the RELEASE TXT file in the root directory for a listing of these programs The drivers for different network operating systems are contained in sepa rate subdirectories Refer to the Readme text file in each subdirectory for instructions on driver installation APPENDIX A SPECIFICATIONS General Network Interface RJ 45 UTP Cable EIA TIA Categories 3 4 5 BNC Coax Cable RG 58 A U or RG 58 C U AUI Drop Cable Standards Supported IEEE 802 3 and ISO IEC 8802 3 10BASE T twisted pair 10BASE2 thin coax and 10BASE5 thick coax PCI Local Bus Specification Rev 2 0 or later Hardware Compatibility PCI local bus compliant PCs Data Bus Width 32 bit I O Address Automatically determined based on configuration space Interrupt INT A on PCI slot pin assignment mapped to the BIOS IRQ setup A 1 SPECIFICATIONS Operating Environment Power Requirements On board 10BASE T transceiver RJ 45 Stand by 5 V 0 025 A Transmit 5 V 0 073 A On board 10BASE2 transceiver BNC Stand by 5 V 0 300 A Transmit 5 V 0 410 A External 10BASE5 MAU AUD Maximum 12 V 0 5 A Temperature 0 to 55 C 32 to 131 F Humidity 10 to 90 non condensing Size 4 84 in x 3 86 in 122 91 mm x 98 18 mm EMC Safety Compliances A 2 FCC Class B CDOC Class B CISPR 22 1985 Class B EN55022 1987 Class B AS NZS 1992 VCCI
21. stralia Sydney 61 2 9238 2206 Fax 61 2 9238 2220 Australia M elbourne 61 3 9653 9461 Fax 61 3 9653 9548 South Africa 27 0 11 784 0414 Fax 27 0 11 784 0363 Asia Pacific 65 336 1800 Fax 65 339 6625 South Asia 65 336 1800 Fax 65 336 3955 Japan 81 3 57212271 Fax 81 3 57212270 EliteF ax SM C s Fax on D emand System U S A and Canada 800 SM C 8329 Elsewhere 516 435 6107 SMC r Printed on recycled paper 350 Kennedy Drive l Hauppauge NY 11788 ag Phone 516 435 6000 Publication N umber 79 000559 000
22. t can be up to 185 m 607 ft long and have a maximum of 30 nodes 1OBASE5 IEEE specifications for Ethemet on thick D type cable Topology Logical or physical arrangement of nodes on a network Shielded Twisted Pair Cable STP Cable composed of two insulated wires twisted together and covered by a foil or braided shielding to reduce electrical interference PCI Local Bus Bus designed by Intel that can function independently of the CPU and that supports a 32 bit data path to the CPU allowing the use of a wide range of 32 bit peripherals Unshielded Twisted Pair Cable UTP Cable composed of two insulated wires twisted together to reduce electrical interference Symbols 10BASE T 1 2 1 3 A 1 A 2 D 2 10BASE2 1 2 A 1 A 2 D 2 10BASE5 1 2 A 1 A 2 C 5 D 2 32 bit bus interface 2 1 D 2 A ACT Status LED 1 4 AUI i 1 1 1 2 1 3 2 1 A 1 A 2 C 5 AUI Pin Assignments B 2 B BNC i ii 1 1 1 2 1 4 A 1 A 2 C 5 D 1 Boot ROM 1 1 D 1 Boot ROM Size _ C 4 C 5 C Configuration 1 1 2 2 A 1 C 1 D Diagnostic Software 2 2 Diagnostics C 1 C 6 Driver Diskette ii 2 2 B 2 Drivers 2 1 2 2 A 3 C 4 E Edge Auto C 8 EEPROM Test C 6 EMC Safety Compliances A 2 EMM386 Fxe C 8 INDEX F Features 1 1 Full duplex 1 1 C 4 C 5 H Hardware Description 1 2 HighScan C 8 C 9 I I O Registers C 7 IEEE 802 3 1 1 1 2 A 1 D 1 Installation 2 1 Introduction 1 1 L LAN Connec
23. the unit will comply only with Class A requirements CDOC Class B This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications Shielded twisted pair cable is required for Class B compliance If unshielded twisted pair cable is used the unit will comply only with Class A requirements Le pr sent appareil num rique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num riques de la classe B prescrites dens le R glement sur le brouillage radio lectrique dict par le minist re des Communications du Canada Une paire torsad e blind e est n cessaire pour l homologation de classe B Si une paire torsad e non blind e est utilis e le dispositif sera conforme aux normes de classe A seulement COMPLIANCES EC Conformity This information technology product was found to comply with EC General Directives 89 336 EEC and 73 23 EEC European Headquarters Standard Microsystems Europe Limited 1st Floor Pyramid House Easthampstead Road Bracknell Berkshire RG12 1NS United Kingdom Compliance with the applicable regulations is dependent upon the use of shielded twisted pair cables VCCI Class B CORB BAER CECH It OBR L IMI BW CHAS HZNS FREB CHEEMMCORRMEHILE AWE LCRA E PEE A EBL RA VCCHIRHE NGA LT BNET LOL REEL IVA FLEVY ay QIU LT CPC
24. tors 1 1 1 2 LED Indicators 1 3 Level Auto C 8 Level Forced C 8 Link Status LED 1 3 Loop Back Test C 7 M Media Type C 4 N NE2000 driver 1 1 Network drivers A 3 O Operating Environment A 2 P Package contents ii PCI BIOS C 4 C 8 PCI Local Bus 1 1 A 1 D 2 I 1 INDEX R RAM Test C 7 Registration Card ii RELEASE TXT 2 2 RJ 45 i 1 1 1 2 2 1 A 1 A 2 C 5 D 1 RJ 45 Pin Assignments B 1 Running Setup C 2 S Setting up a new configuration C 4 SETUP EXE C 1 C 2 Specifications A 1 T Thick coax cable 1 1 1 2 2 1 A 1 Thin coax cable 1 1 1 2 2 1 A 1 D 1 Trigger method C 8 Twisted pair cable 1 1 1 2 2 1 A 1 D 2 V Viewing the current configuration C 2 Il 2 SMC Limited Warranty HARDWARE Standard Microsystems Corporation SMC warrants the EZ Card 10 PCI network cards to be free from defects in workmanship and materials under normal use and service for the following length of time from the date of purchase from SMC or its Authorized Reseller EZ Card 10 PCI Network Cards 000 cece eeee Limited Lifetime If a product does not operate as warranted during the applicable warranty period SMC shall at its option and expense repair the defective product or part deliver to Customer an equivalent product or part to replace the defective item or refund to customer the purchase price paid for the defective product All products that are replaced will become the
Download Pdf Manuals
Related Search