Smooth Fitness 5.45 Treadmill User Manual
Contents
1. EN POWER REQUIREMENTS Power Requirements IMPROPER CONNECTION OF THE EQUIPMENT GROUNDING CONNECTOR CAN RESULT IN A RISK OF AN ELECTRIC SHOCK CHECK WITH A QUALIFIED ELECTRICIAN OR SERVICE MAN IF YOU ARE IN DOUBT AS TO WHETHER THE PRODUCT IS PROPERLY GROUNDED DO NOT MODIFY THE PLUG PROVIDED WITH THE PRODUCT IF IT WILL NOT FIT THE OUTLET HAVE A PROPER OUTLET INSTALLED BY A QUALIFIED ELECTRICIAN This treadmill can be seriously damaged by sudden voltage changes in your home s electrical power Voltage spikes surges and noise interference can result from weather conditions or from other appliances being turned on or off To reduce the possibility of treadmill damage always use a surge protector not included with your treadmill Surge protectors can be purchased at most hardware stores The manufacturer recommends a single outlet surge protector with a UL 1449 rating as a Transient Voltage Surge Suppressor TVSS with a UL suppressed voltage rating of 400V or less and an electrical rating 110VAC 15 amps This treadmill must be grounded to reduce the risk of electrical shock Grounding provides a path of least resistance for electric current should the treadmill malfunction This treadmill comes with an electrical cord having an eguipment grounding conductor and a grounding plug Always plug the power cord into a surge protector and plug the surge protector into an appropriate outlet that is properly installed and grounded in accordance with a2. treadmill will stop and return to P2 start display Press STOP ENTER to go to POWER ON status P3 INTERVAL SPEED If you select the P3 INTERVAL SPEED program the upper and lower LCD will show the following After completing the user information set up the SPEED CALORIES and PULSE LCD display 0 The TIME display shows factory setting 24 00 and a blinking workout load level shows 1 Press the INCLINE UP DOWN buttons to adjust the workout load level from 1 to 12 then press the STOP ENTER button to confirm the setting Then the TIME LCD will display a blinking 24 00 Press the INCLINE UP DOWN buttons to adjust the total workout time and press STOP ENTER button to confirm the setting Press the START button to start the workout The SPEED start and change follows the pre set workout load speed chart as below The TIME counts down from the set up workout time The CALORIES and DISTANCE count up from 0 INCLINE LEVEL starts from level 0 LEVEL MIN SPEED MAX SPEED 1 1 8 3 0 2 2 0 3 4 3 2 2 3 8 4 2 4 4 2 5 2 6 4 6 6 2 8 5 0 7 3 0 5 4 8 3 2 5 8 9 3 4 6 2 During the workout press the INCLINE UP DOWN button to adjust the incline level Users can overwrite the speed by pressing the SPEED UP DOWN buttons COOL DOWN After the pre set TIME counts down to 0 the treadmill will start a one minute cool down program The TIME LCD will display COOL and blink for 10 seconds and continue counting down 50 second
3. DESCRIBED IN THIS FORM THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE 5 45 MOTORIZED TREADMILL IMPORTANT STEPS Warning Before using this product please consult your personal physician for a complete physical examination Frequent and strenuous exercise should be approved by your doctor first If any discomfort should result from your use of this product stop exercising and consult your doctor Proper usage of this product is essential Please read your manual carefully before exercising Please keep all children away from the equipment during use and when equipment is unattended Always wear appropriate clothing including athletic shoes when exercising Do not wear loose clothing that could become caught during exercising Make sure that all bolts and nuts are tightened when equipment is in use Periodic maintenance is required on all exercise equipment to keep it in good condition Before beginning How you begin your exercise program depends on your physical condition If you have been inactive for several years or are severely overweight you must start slowly and increase your time gradually a few minutes per week Initially you may be able to exercise only for a few minutes in your target zone However your aerobic fitness will improve over the next six to eight weeks Don t be discouraged if it takes longer It s important to work at your own
4. next steps of assembly C Attach the Handle Bar Cover LR 208 to the underside of the console and the inside of the left upright 301 Secure with four M4x15mm screw 802 And secure with two M4x15mm screw 802 between the Handle Bar Cover LR 208 outside and the console housing upper D Attach the Handle Bar Cover LL 207 to the top of the console and the outside of the Upright Left 301 And secure with four M4x15mm screw 802 E Repeat the above process for the right hand side cover 209 and cover 210 as shown in diagram 802 X20 um 5 45 MOTORIZED TREADMILL ASSEMBLY STEP 6 Assembly base covers NOTE Refer to folding instructions on page 27 A Fold up the running deck until it locks in place B Attach Upright Base Cover 302 to the outside of the Left Upright 301 Secure with two M4x15 mm screw 802 C Attach Upright Base Cover 303 to the inside of the Left Upright 301 Secure with 802 X7 G one M4x15 mm screw 802 D Attach Upright Base Cover 305 to the outside of the Right Upright 301 Secure with three M4x15 mm screw 802 E Attach Upright Base Cover 304 to the inside of the Right Upright 301 Secure with one M4x15 mm screw 802 5 45 MOTORIZED TREADMILL 24 ASSEMBLY STEP7 Attaching Rubber Cover Insert the rubber cover 306 into the slot upright base cover 8 5 45 M
5. off center resulting in the belt rubbing with the plastic side rail or end caps and possibly causing damage To adjust the belt back to it s proper position please follow the directions below e Walking belt has shifted to the left First unplug the power cord from the surge protector Using the hex key provided turn the left rear roller adjustment bolt 1 4 turn in the clockwise direction Plug the power cord back into the surge protector and run the treadmill at 2 5 mph You should see the belt start to correct itself moving back towards the center Repeat the above procedure until the walking belt is centered It may be necessary to set walking belt tension once you have completed this procedure if the belt feels like it is slipping while walking Refer below to the Walking belt slipping instructions e Walking belt has shifted to the right First unplug the power cord from the surge protector Using the hex key provided turn the right rear roller adjustment bolt 1 4 turn in the clockwise direction Plug the power cord back into the surge protector and run the treadmill at 2 5 mph You should see the belt start to correct itself moving back towards the center Repeat the above procedure until the walking belt is centered It may be necessary to set walking belt tension once you have completed this procedure if the belt feels like it is slipping while walking Refer below to the Walking belt slipping instructions e Walking belt is slipping Firs
6. repeat these exercises to reduce sore muscle problems We suggest the warm up and cool down exercises on the following pages Slowly bend forward from your waist letting your back and shoulders relax as you stretch toward your toes Reach down as far as you can and hold for 15 counts Lift your right shoulder up toward your ear for one count Then lift your left shoulder up for one count as you lower your right shoulder Sit with the soles of your feet together with your knees pointing outward Pull your feet as close into your groin as possible Gently push your knees towards the floor Hold for 15 counts Sit with your right leg extended Rest the sole of your left foot against your right inner thigh Stretch toward your toe as far as possible Hold for 15 counts Relax and then repeat with left leg extended Open your arms to the side and continue lifting them until they are over your head Reach your right arm as far upward toward the ceiling as you can for one count Feel the stretch up your right side Repeat this action with your left arm Rotate your head to the right for one count feeling the stretch up the left side of your neck Next rotate your head back for one count stretching your chin to the ceiling and letting your mouth open Rotate your head to the left for one count and finally drop your head to your chest for one count Lean against a wall w
7. side of your neck between the windpipe and the large neck muscles Count the number of beats in ten seconds and then multiply that number by six This gives you the number of beats per minute How fast should your heart beat during aerobic exercise Fast enough to reach and stay in its target zone a range of beats per minute that is largely determined by your age and physical condition To determine your target zone consult the chart we have provided a 5 E y o W a 2 Ss E lt o E a lt u I x gt o gt 45 50 YOUR AGE in years FITNESS Optimal training aerobic or cardiovascular HEALTH Beginner low intensity with long duration produces fat burning You can calculate the target heartrate for vour training as follows Maximum heartrate 220 minus age For the different trainingtargets you should train with the following percentage of your maximum heartrate HEALTH 50 70 of your max heartrate FITNESS 70 80 of your max heartrate ADVANCED 80 90 of your max heartrate Example You are 25 years old and want to train for the target Fitness 220 25 195 70 of 195 136 5 80 of 195 156 Your target heartrate should be between 136 5 and 156 beats per minute Aerobic exercise Is any sustained activity that sends oxygen to your muscles via your heart and lungs It will improve the fitness of your lungs and heart your body s most importa
8. speed will increase by 0 5MPH 0 8KPH per 30 seconds If the actual pulse reaches 65 of the maximum heart rate the speed will remain unchanged If the actual pulse reaches 65 of the maximum heart rate over one minute then the speed will be maintained the same until the warm up program finishes If the actual user s pulse fails to reach 65 of the maximum heart rate within the first 3 minutes of warm up the computer will continue the second 3 minutes warm up program All workout information continues to count up and the timer counts down from 3 00 During the second 3 minute warm up the computer will change the incline level instead of speed If the heart rate monitor fails to sense the user s pulse The PULSE LCD will display P and blink the computer will not change the incline level If the heart rate monitor senses the user s pulse properly and the actual user s pulse does not reach 65 of the maximum heart rate 220 age x 65 then the incline level will be increased by 1 level per 30 seconds If the actual pulse reaches 65 of the maximum heart rate the incline level will remain unchanged If the actual pulse reaches 65 of the maximum heart rate over one minute then the speed will be maintained the same until the warm up program finishes If the actual user s pulse fails to reach 65 of the maximum heart rate within the second 3 minutes of warm up the computer will continue the third 3 minutes warm up program All workout information continu
9. step A Place the front handle bar 201 on top of the left and right upright 301 B Secure left side with one 8 washer 812 and M8x45 mm Allen bolt 805 in the forward most hole C Secure right side with one 8 washer 812 and M8x45 mm Allen bolt 805 in the forward most hole 812 X2 D Connect pulse wire 217 and wire 111 on left and right side as shown in diagram Then insert the remaining length of the wire into the front handle bar tube Tighten all bolts with Allen Wrench 5 45 MOTORIZED TREADMILL ASSEMBLY STEP4 Assemble The Side Handlebars 810 x4 A NOTE Side rails are interchangeable for use on both right and left sides A Attach one handlebar 202 to the left upright 301 B Secure the Side Handlebar with one M8 x75 mm bolt 845 and one 8 washer 812 through the top of front handle bar into the side handle bar C Insert two M8x18 mm 810 and two 8 washer 812 through the side handrail plate and thread into the upright D Repeat the above process for the right side E Tighten all bolts with Allen Wrench 845 X2 CC 5 45 MOTORIZED TREADMILL ASSEMBLY STEP5 Assemble Computer Console A Rotate the console until it stops as shown in diagram below B Tighten the screw 807 of the console connect tube 213 for right and left side Console connect tube 213 will be adjust for the
10. time calories all count up from 0 all P2 INTERVAL INCLINE If you select the P2 INTERVAL INCLINE program the upper and lower LCD will show the following After completing the user information set up SPEED CALORIES and PULSE LCD display O The TIME display shows factory setting 24 00 and the blinking workout load level shows 1 Press the INCLINE UP DOWN buttons to adjust the workout load level from 1 to 12 then press the STOP ENTER button to confirm the setting Then the blinking TIME LCD displays 24 00 Press the INCLINE UP DOWN buttons to adjust the total workout time and press the STOP ENTER button to confirm the setting Press the START button to start the workout SPEED starts from 2 0MPH 3 2KPH The TIME counts down from the set up workout time The CALORIES and DISTANCE count up from 0 INCLINE LEVEL follows the pre set chart as follows 5 45 MOTORIZED TREADMILL EEE COMPUTER OPERATION LEVEL MIN LEVEL MAX LEVEL 1 0 4 2 1 5 3 2 6 4 3 7 5 4 8 6 5 9 7 6 10 8 7 11 9 8 12 During the workout press the SPEED UP DOWN buttons to adjust the speed Users can overwrite the incline level by pressing the INCLINE UP DOWN buttons COOL DOWN After the pre set TIME counts down to 0 treadmill will start a one minute cool down program The TIME LCD will display COOL and blink for 10 seconds and continue counting down 50 seconds at speed 2 MPH 3 2KPH After a one minute cool down the
11. treadmill Apply from front to back 5 45 MOTORIZED TREADMILL EE warranty Read and follow the assembly instruction and the User s Manual before using this product Warranty Coverage Smooth Fitness and EVO Fitness warrants to the original owner that each new product to be free from defects in workmanship and material Under normal use and conditions This warranty is limited on home use only Period of Coverage The Warranty on this product runs from the date of original purchase using the following schedule Model Name Frame Drive Motor Parts amp Electronics Labor 5 45 Lifetime Lifetime 3 years 1year Labor Smooth Fitness will reimburse for labor costs for One 1 year Smooth Fitness reserves the right to either Hire and reimburse an independent service technician who will come into the home for the repair OR In the event that there is not an available certified Smooth Fitness service technician Smooth will send the part directly to the consumer and will pay 75 US per occurrence for the labor costs of such repair If multiple repair attempts must be made for one reported problem Smooth will only reimburse once per occurrence Smooth Fitness reserves the right to inspect damaged parts for misuse Your Original Receipt is proof of purchase and should be kept with the product manual You may be reguired to show proof of purchase prior to warranty service being initiated Remedy Provided by S
12. 0 and 6 program LED lights blink individually The LOWER LCD shows 0 on all windows SLEEP MODE When the power is ON the computer will automatically enter SLEEP MODE if it is left idle for 3 minutes without receiving any input Press any button to return to POWER ON status when the computer is in the SLEEP MODE DISPLAY MODE This feature is designed only for store display purpose To cancel the SLEEP MODE feature pull out the safety key press and hold the SPEED UP and DOWN buttons insert the safety key to power on the treadmill After one short beep sound the SLEEP MODE will be cancelled and the LCD will not go off as long as the power switch stays on and the safety key is inserted properly ENGLISH METRIC CONVERSION The computer has been preset to calculate and show all information in English miles pounds inches The computer can be set to display information in Metric kilometers kilograms centimeters To do this set the POWER SWITCH located on the base frame to ON Press and hold the START button Insert the SAFETY KEY The computer will sound one short BEEP and the UPPER LCD will show KM and blink Press the INCLINE UP DOWN button to switch between KM and ML KM means Metric and ML means English Press the STOP ENTER button to confirm the setting and return to POWER ON status after one long beep sound OUICK START When the treadmill is in POWER ON status press the START button to activate the QUICK START The SPEED LCD count
13. 1 5 45 830 831 M8x85 Screw 1 5 45 831 832 26x 8 5x3 Washer 2 5 45 832 833 25 Rubber Cushion 1 5 45 833 834 M8x30 Bolt 4 5 45 834 835 M5x14 Screw 4 5 45 835 836 M4x19 Screw 16 5 45 836 837 M3x8 Screw 2 5 45 837 838 M8x23 Screw 6 5 45 838 839 M6x45 Bolt 3 5 45 839 840 6 Washer 3 5 45 840 841 M10x33 Bolt 1 5 45 841 842 M10x56 Bolt 2 5 45 842 843 M8x36 5 Bolt 1 5 45 843 844 M10x43 5 Bolt 1 5 45 844 845 M8x75 Bolt 2 5 45 845 846 M8x30 Screw 2 5 45 846 847 3mm Rubber Cushion 2 5 45 847 848 M10x26 Bolt 2 5 45 848 849 M8x20 mm Bolt 1 5 45 849 5 45 MOTORIZED TREADMILL PARTS DIAGRAM 5 45 MOTORIZED TREADMILL PARTS DIAGRAM 5 45 MOTORIZED TREADMILL PARTS DIAGRAM 5 45 MOTORIZED TREADMILL PARTS DIAGRAM en 812 610 3 a X 815 61 5 45 MOTORIZED TREADMILL PARTS DIAGRAM 823 519 820 828 lt gt 648 Es o 816 819 a ve vid 5 L RE AN 919621 entr 5 45 MOTORIZED TREADMILL PARTS DIAGRAM 5 45 MOTORIZED TREADMILL PARTS DIAGRAM 5 45 MOTORIZED TREADMILL ASSEMBLY STEP 1 Unpacking and Inventory NOTE FOR SAFER AND EASIER TRANSPORTATION DO NOT REMOVE THE PLASTIC P 5 Components RETAINING STRAPS UNTILL THE UNIT
14. HEART RATE CONTROL program the LCD will show the following After completing the user information set up the TIME LCD shows the blinking factory pre set workout time 60 00 Press the INCLINE UP DOWN buttons to adjust the workout time and press the STOP ENTER button to confirm Then the upper LCD shows initial speed 2 0MPH 3 2KPH and the lower LCD shows initial warm up time 3 00 Press the START button to start the 3 minutes WARM UP program Speed starts from 2 0MPH 3 2KPH and INCLINE LEVEL starts from level 0 Please keep your hand on the hand pulse grips all the time during this workout in order to monitor your pulse correctly During the program if the heart rate monitor fails to sense the pulse you will see P blinking on the PULSE LCD If the heart rate monitor senses the pulse properly you will see the stable heart beat sign on the PULSE LCD and the correct pulse readout on the PULSE LCD The computer will sense the user pulse every 30 seconds During the warm up program you can press the STOP ENTER button to pause or stop the program or press the START button to re start the program Other buttons will not react during this warm up process During the warm up program if heart rate monitor fails to sense the user s pulse The PULSE LCD will display P and blink the computer will not change the speed If heart rate monitor senses the user s pulse properly and the actual user s pulse does not reach 65 of the maximum heart rate 220 age x 65 then
15. IS IN THE AREA OF ASSEMBLY P 6 Hardware and Tools Remove the treadmill and all the components and hardware from the box Check the quantities of all components and hardware with the component and hardware lists on pages 5 6 er G Z 8 e TI Warning DO NOT REMOVE THE PLASTIC STRARS Until unit is in its final place of assembly 5 45 MOTORIZED TREADMILL ASSEMBLY STEP 2 Assemble Upright Frame NOTE Make sure all wires are recessed into the frame DO NOT trap or pinch Hand tight bolts until last step A Raise the left and right uprights 301 B Secure the left upright 301 with two 8x18 mm Allen bolts 810 and two 8 washer 812 through the front side of the base frame hand tighten C Secure the right upright 301 with two 8x18 mm Allen bolts 810 and two 8 washer 812 through the front side of the base frame hand tighten D Insert one M 8x52 mm Allen bolt 811 and one 8 washer 812 through the side of the base frame and the left upright hand tighten E Insert one M 8x52 mm Allen bolt 811 and one 8 washer 812 through the side of the base frame and the right upright hand tighten F Tighten all Allen bolts with Allen wrench C Provided with hardware so xo MA O 5 45 MOTORIZED TREADMILL ASSEMBLY STEP 3 Assemble Front Handle Bar NOTE Only hand tighten bolts until last
16. OTORIZED TREADMILL ASSEMBLY STEP 8 Inserting Water Bottle Holders Attach the Water Bottle Holder 108 to the Console Housing Upper 104 and push down until snap in place 5 45 MOTORIZED TREADMILL ASSEMBLY COMPLETE Assembly is now complete Check that all the components are secure and all the hardware is tight By this step all bolts and screws should be wrench tight If any hardware is not wrench tight go back and tighten The finished product should resemble the picture below Serial Number L Folding Lock The safety key must be inserted for the treadmill There are two orange levers on this treadmill The to function The safety key tether should be worn most forward lever is the folding lock which is at all times when the treadmill is in use This used in folding and unfolding this treadmill The safety feature is designed to prevent injury other is used for transporting from one location to another 5 45 MOTORIZED TREADMILL FOLDING INSTRUCTIONS How to fold up the treadmill Your treadmill can be folded up for space saving storage To do this follow the instructions here Kir NN Do gt D AUS US Lift the deck from the rear towards the computer console Listen for the click of the Folding Level locking mechanism Be sure locking mechanism is engaged before transpo
17. OWNER S MANUAL 5 45 MOTORIZED TREADMILL USER WEIGHT LIMITATION 275LBS SERIAL NUMBER Found on Frame Copyright 20081 TG 5 45 MOTORIZED TREADMILL a PRECAUTIONS For future service or related guestions Please staple your receipt and or write in the name and phone number of the retail store where you purchased your treadmill Name Phone Number Receipt Precautions WARNING To reduce the risk of burns fire electric shock or injury to persons read the following important precautions and information before operating the treadmill It is the responsibility of the owner to ensure that all users of this treadmill are adeguately informed of all warnings and precautions e Use the treadmill only as described in this manual e Place on a level surface with 6 feet 2 m of clearance behind it Do not place the treadmill on any surface that blocks air openings To protect the floor or carpet from damage place a mat under the treadmill e When choosing a location for the treadmill make sure that the location and position permit access to a plug e Keep the treadmill indoors away from moisture and dust Do not put the treadmill in a garage or covered patio or near water e Do not operate the treadmill where aerosol products are used or where oxygen is being administered e Keep children under the age of 12 and pets away from the treadmill at all times e The treadmill should not be used by persons weighing mor
18. T Part No Description Oty Order No 607 Main Frame Cross Bar 1 5 45 607 700 Complete Deck Frame Components 701 Deck Frame 1 5 45 701 702 Front Roller Shaft 1 5 45 702 703 Front Roller Tube 1 5 45 703 704 Rear Roller Shaft 1 5 45 704 705 Rear Roller Tube 1 5 45 705 706 Running Deck Rear Wheel 2 5 45 706 707 Cushion Pad 6 5 45 707 800 Complete Hardware Pack 801 M3 5x16 Screw 8 5 45 801 802 M4x15 Screw 59 5 45 802 803 M3x10 Screw 2 5 45 803 804 4 Washer 4 5 45 804 805 M8x45 Bolt 2 5 45 805 806 M4x8 Screw 4 5 45 806 807 M5x30 Screw 4 5 45 807 808 M3x14 Screw 4 5 45 808 809 M8x49 Bolt 1 5 45 809 810 M8x18 Bolt 8 5 45 810 811 M8x52 Bolt 4 5 45 811 812 8 Washer 22 5 45 812 813 M4x25 Screw 2 5 45 813 814 Transportation Wheel Bolt 3 5 45 814 815 5 Washer 3 5 45 815 816 M5x10 Screw 3 5 45 816 817 M4x14 Screw 3 5 45 817 818 M10 Nylon Nut 13 5 45 818 819 M10x67 Bolt 2 5 45 819 820 14x50 Bolt 2 5 45 820 821 33x 8x10 Screw 2 5 45 821 823 4x45 Screw 2 5 45 823 824 M10x116 Screw 1 5 45 824 825 8 Nylon Nut 3 5 45 825 826 M8x12 Bolt 2 5 45 826 827 8 Washer 2 5 45 827 828 10 Washer 5 5 45 828 829 14 Clip 2 5 45 829 5 45 MOTORIZED TREADMILL F COMPLETE PARTS LIST Part No Description Qty Order No 830 M8x48 Screw
19. e than 275 LBS e Never allow more than one person on the treadmill at a time Wear appropriate exercise clothing when using the treadmill Do not wear loose clothing that could become caught in the treadmill Athletic support clothes are recommended for both men and women Always wear athletic shoes Never use the treadmill with bare feet wearing only stockings or in sandals e When connecting the power cord plug the power cord into a grounded circuit No other appliance should be on the same circuit e Always straddle the belt and allow it to start moving before stepping onto the belt e Always examine your treadmill before using to ensure all parts are in working order e Allow the belt to fully stop before dismounting e Never insert any object or body parts into any opening e Follow the safety information in regards to plugging in your treadmill e Keep the power cord away from the incline wheels and do not run the power cord underneath your treadmill Do not operate the treadmill with a damaged or frayed power cord e Always unplug the treadmill before cleaning and or servicing Service to your treadmill should only be performed by an authorized service representative unless authorized and or instructed by the manufacturer Failure to follow these instructions will void the treadmill warranty e Never leave the treadmill unattended while it is running e The equipment is for Class B Home Use 5 45 MOTORIZED TREADMILL
20. ek DECK LUBRICATION The walking belt has been pre lubricated at the factory However it is recommended that the walking board be checked periodically for lubrication to ensure optimal treadmill performance Your treadmill should not have to be lubricated usually within the first 400 hours of use Every 2 months of operation lift the sides of the walking belt and feel the top surface of the walking board as far as you can reach If you feel signs of silicone no further lubrication is required If it feels dry to the touch follow the instructions below Please use Lube N Walk can be purchased from your dealer or call the number on the front of the manual or a non petroleum based silicone such as Napa 8300 available at most stores To purchase lubricant kit please contact Smooth Fitness 1 888 800 1167 To apply lubricant to the walking belt 1 Position the walking belt so that the seam is located on top and in center of the walking board 2 Insert the spray nozzle into the spray head of the lubricant can 3 While lifting the side of the walking belt position the spray nozzle between the walking belt and the board approximately 6 from the front of the treadmill Apply the silicone spray to the walking board moving from the front of the treadmill to the rear Repeat this on the other side of the belt Spray approximately 1 4 bottle supplied with treadmill each side 4 Allow the silicone to set for 1 minute before using the
21. er LCD will show P and the PULSE LCD shows the blinking factory target heart rate setting Press the INCLINE UP DOWN buttons to adjust the user target heart rate properly for your own physical condition and press the STOP ENTER button to set the user TARGET HEART RATE Now you have completed the user information set up For the 2 or other member in the family please assign a different user ID This treadmill can allow set and memorize 9 different user s information For the repeat user after pressing the program button please press the INCLINE UP DOWN buttons to select the USER ID that you assigned previously Each time when the treadmill is switched off and switched on again it will enter the select program procedure The user ID will show the user ID of the previous user OPERATE PROGRAM After completing the USER INFORMATION SET UP prior to starting the program you selected please follow the procedure to operate the different programs as described below 3 P1 MANUAL PROGRAM If you select the P1 MANUAL program the upper and lower LCD will show the following After completing the user information set up the SPEED LCD displays the initial speed 2 0MPH 3 2KPH and the PULSE LCD displays P TIME CALORIES AND INCLINE LEVEL all show 0 Press the START button to start the workout Press the SPEED UP DOWN buttons to adjust the speed from 0 5MPH to 10MPH and press the INCLINE UP DOWN buttons to adjust the incline level from level 0to 15 Distance
22. es to count up and the timer counts down from 3 00 During the third 3 minutes warm up both speed and incline remain unchanged regardless of the actual pulse If time counts down to 0 and 65 of the max heart rate still cannot be reached the TIME LCD will show FAIL and the program will stop and return to POWER ON status After the warm up program if the actual pulse reaches 65 of the max heart rate to complete warm up program the computer will enter the HEART RATE CONTROL program TIME counts down from the previous setting Distance and Calories will continue counting up from the warm up program During the HEART RATE CONTROL program the heart rate monitor will sensor the actual user s pulse every 30 seconds If the actual user s pulse does not reach 85 of the max heart rate then the incline level will be increased by 1 level every 30 seconds If the actual user s pulse reaches 85 of the max heart rate then the treadmill performance will be remained the same If the actual user s pulse is above 85 of the max heart rate the incline level will be reduce by 1 level Speed will remain unchanged until the incline level increase up to 15 or the incline level down to 0 If the incline level is up to 15 and still 85 of the max heart rate cannot be reached then speed will start increasing by 0 5MPH 0 8KPH every 30 seconds If the incline level is down to 0 and still lower than 85 of the max heart rate cannot be reached then the speed will
23. ith your left leg in front of the right and your arms forward Keep your right leg straight and the left foot on the floor then bend the left leg and lean forward by moving your hips toward the wall Hold and then repeat on the other side for 15 counts 5 45 MOTORIZED TREADMILL MI TROUBLESHOOTING NOTE Do not touch any internal electric wires without consulting the manufacturer Treadmill will not start Symptom Resolution Treadmill will not power up Check the following Make sure the power cord is plugged into a surge protector the surge protector is plugged into a properly grounded outlet and the surge protector is turned on refer to the Power Reguirements section in this manual Equipment circuit breaker is in the reset position Equipment power switch is in the on position Safety key is properly inserted into the computer console Wall outlet is properly functioning with correct voltage Have an electrician check for inadequate voltage at the outlet refer to the Power Requirements section in this manual House circuit breaker is reset and is the proper size refer to the Power Reguirements section in this manual Treadmill stops operation during use Safety key is properly inserted into the computer console Eguipment circuit breaker is in the reset position House circuit breaker is reset meets proper reguirements and if worn replaced b
24. ll local codes and ordinances This product is for use on a nominal 110 volt circuit and has a grounding plug that looks like the plug illustrated in the drawing below GFCI outlets and GFCI Circuit Breakers are NOT recommended for use on this product GFCI outlets and GFCI Circuit Breakers may cause this eguipment to improperly function GROUNDING OUTLET GROUNDING OUTLET TREADMILL POWER CORD SURGE PROTECTOR GROUNDING PLUG GROUNDING PIN SCREW SURGE PROTECTOR SURGE PROTECTOR GROUNDING PLUG 3 PRONG OUTLET 2 PRONG OUTLET 5 45 MOTORIZED TREADMILL a E BEFORE YOU BEGIN Open the boxes Open the boxes of your new equipment Inventory all parts included in the boxes And Compare them to the supplied components and supplied Hardware lists on pages 5 6 for a full count of the parts included If you are missing any parts or have any assembly questions contact us directly at 888 800 1167 Assembly instructions begin on page 18 Gather your tools Before starting the assembly of your unit make sure that you have gathered all the necessary tools you may require to assemble the unit properly Having all of the necessary equipment at hand will save time and make the assembly quick and hassle free Clear your work area Make sure that you have cleared away a large enough space to properly assemble the unit Make sure the space is free from anything that may cause injury during assembly After the unit is fully as
25. lower by 0 5MPH 0 8KPH every 30 seconds If the actual user s pulse reaches above 85 of max heart rate over 3 minutes the HEART RATE CONTROL program will be shut down and the computer will enter the one minute COOL DOWN program When the TIME counts down to 0 the HEART RATE CONTROL program is completed and the computer will enter the one minute COOL DOWN program After the COOL DOWN program the computer will return to POWER ON status The purpose of the HEART RATE CONTROL program is to keep the user s pulse between 65 of the max heart rate and 85 of the max heart rate as to reach the most efficient workout result 5 45 MOTORIZED TREADMILL E maintenance HOW TO MAINTAIN THE SMOOTH 5 45 TREADMILL Proper maintenance is very important to ensure your treadmill is always in top working condition Improper maintenance could cause damage or shorten the life of your treadmill and exceed the LIMITED WARRANTY coverage e Important Do not use abrasives or solvents to clean the treadmill To prevent damage to the computer keep liquids away and keep it out of direct sunlight e Inspect and tighten all parts of the treadmill regularly Replace any worn parts immediately BELT ADJUSTMENT Belt adjustment and tension performs two functions adjustment for tension and centering The running belt has been adjusted properly at the factory However transportation uneven flooring or other unpredicted reasons could cause the belt to shift
26. lt See process in owner s manual Smooth Fitness 80 5th Ave King of Prussia PA 19406 Toll Free Customer Service 1 888 800 1167 Website www smoothfitness com Copyright O 2008 Greenmaster Industrial Corp All rights reserved
27. mooth Fitness Smooth Fitness will provide a replacement part free of charge if a defect is found during the Warranty period Smooth Fitness may at its discretion choose to provide any of following parts or repair options In the event that a part is determined in need of replacement upon receipt of the part by Smooth Fitness Smooth Fitness may send out the part by UPS ground or another such carrier directly to the customer s home The customer is responsible for the cost of sending the part to Smooth Fitness Any redemption may be by repair or replacement of the affected parts and or product at the sole discretion of Smooth Fitness by personnel approved by Smooth Fitness Parts repaired or replaced pursuant to this Warranty shall be warranted for the unexpired portion of the Warranty applying to the original product Any technical advice furnished before or after delivery in regard to the use or application of Smooth Fitness products is furnished without charge and on the basis that it represents Smooth Fitness best judgment under the circumstances but that the advice is used at your sole risk Procedure for Obtaining Your Remedy Under This Warranty To obtain service on a Smooth Fitness product call Smooth Fitness In the instance that service is not available in an area Smooth Fitness at its discretion can either 1 find a service technician in your area to perform warranty service 2 have a local dealer perform warranty service or 3 send the wa
28. n to 0 the treadmill will start a one minute cool down program The TIME LCD will display COOL and blink for 10 seconds and continue counting down 50 seconds at a speed of 2MPH 3 2KPH After a one minute cool down the treadmill will stop and return to P2 start display Press STOP ENTER to go to POWER ON status 53 P5 5K SELF LEARING COMPETITION If you select the P5 5K SELF LEARNING COMPETITION program the upper and lower LCD will show the following After completing the user information set up the DISTANCE LCD shows preset distance 3M 5KM The TIME CALORIES and INCLINE LEVEL LCD display O and the PULSE LCD display shows P Press the START button to start the program Speed starts from 2 0MPH 3 2KPH The TIME and CALORIES count up from 0 Incline level follows the factory pre set profile DISTANCE counts down from 3ML 5KM During the workout you can adjust the speed by pressing the SPEED UP DOWN buttons and overwrite the INCLINE LEVEL by pressing the INCLINE UP DOWN buttons COOL DOWN After the pre set DISTANCE counts down to 0 the treadmill will start a one minute cool down program The TIME LCD will display COOL and blink for 10 seconds and continue counting down 50 seconds at a speed of 2MPH 3 2KPH After a one minute cool down the treadmill will stop and return to P2 start display Press STOP ENTER to go to POWER ON status 5 45 MOTORIZED TREADMILL COMPUTER OPERATION V P6 HEART RATE CONTROL If you select the P6 5K
29. nt muscle Aerobic fitness is promoted by any activity that uses your large muscle groups arms legs or buttocks for example Your heart beats quickly and you breathe deeply An aerobic exercise should be part of your entire exercise routine 5 45 MOTORIZED TREADMILL MUSCLE CHART Targeted muscle groups The exercise routine that is performed on this product will develop primarily lower body muscle groups These muscle groups are shown in gray color on the chart below MUSCLE GROUPS Shoulder muscles Calf muscles Pectoral muscles Trapeziums muscles Bicep muscle Triceps muscles Abdominal muscles Back muscles Forearm muscles Gluteus muscles Ouadriceps muscles Hamstring muscles 5 45 MOTORIZED TREADMILL STRETCHING ROUTINE Warm up and cool down A successful exercise program consists of a warm up aerobic exercise and a cool down Do the entire program at least two and preferably three times a week resting for a day between workouts After several months you can increase your workouts to four or five times per week Warming up is an important part of your workout and should begin every session It prepares your body for more strenuous exercise by heating up and stretching out your muscles increasing your circulation and pulse rate and delivering more oxygen to your muscles At the end of your workout
30. pace Ultimately you ll be able to exercise continuously for 30 minutes And the better your aerobic fitness the harder you will have to work to stay in your target zone But remember these essentials e Contact your physician before starting a workout or training program Have your doctor review your training and diet programs to advise you of a workout routine you should adopt e Begin your training program slowly with realistic goals that have been set by you and your doctor e Supplement your program with some type of aerobic exercise such as walking jogging swimming dancing and or bicycling Monitor your pulse frequently If you do not have an electronic heart rate monitor have your physician show you the proper way to manually check your pulse by using your wrist or neck Establish your target heart rate based on your age and condition e Drink plenty of fluids during the course of your routine You must replace the water content lost from excessive exercising to avoid dehydration Avoid drinking large amounts of cold liquids Fluids should be at room temperature when consumed The Surgeon General has determined that lack of physical activity is detrimental to your health 5 45 MOTORIZED TREADMILL 40 E 1arncer HEART RATE Finding your pulse To make sure your heart is beating in its target zone you ll need to know how to monitor your heart rate The easiest way is to feel the pulse in the carotid artery on either
31. program and preset function values setting mode 2 Press to run setting procedure before pressing the START KEY 3 Press to stop exercise during workout time SPEED UP 1 Press to increase exercise speed by 0 1MPH KPH 2 Hold the button to rapidly increase speed by 0 5MPH KMPH per second and release the button to stop the function SPEED DOWN 1 Press to decrease exercise speed by 0 1MPH KPH 2 Hold the button to rapidly decrease speed by 0 5MPH KMPH per second and release the button to stop the function INCLINE UP DOWN 1 Press up or down to change incline level 2 Press to select programs and preset related function value SAFETY KEY The safety key must be inserted into the slot on the console in order to operate the treadmill Always insert the safety key and attach the clip to your clothing at your waist before beginning your workout If you should encounter problems and need to stop the motor guickly simply pull on the cord to disengage the safety key from the console To continue operation first turn the power switch to off and set the speed controller to stop Next turn the power switch to on and reinsert the safety key into the console 5 45 MOTORIZED TREADMILL EE COMPUTER OPERATION POWER ON Set the POWER SWITCH located on the base frame to ON and insert the SAFETY KEY The UPPER LCD and LOWER LCD screens light up all digits and enter the POWER ON mode The UPPER LCD SPEED DISTANCE window shows 0
32. r Cushion 2 5 45 402 403 Rubber Cushion 2 5 45 403 404 Power Switch Plate Base 1 5 45 404 405 Power Switch Plate Cover 1 5 45 405 406 Power Switch Plate 1 5 45 406 407 Power Breaker 1 5 45 407 408 Power Switch 1 5 45 408 409 Front Caster 2 5 45 409 410 Cushion 2 5 45 410 411 Foot Locker 1 5 45 411 412 Transportation Wheel Bracket 1 5 45 412 413 Spring 1 5 45 413 414 Transportation Wheel 1 5 45 414 415 Fold Up Locker 1 5 45 415 416 Spring Of The Fold Up Locker Assembly 1 5 45 416 500 Complete Motor Components 501 Motor Hood Top 1 5 45 501 502 Driving Motor 1 5 45 502 503 Motor Holder 1 5 45 503 504 Driving Belt 1 5 45 504 505 Control Board 1 5 45 505 506 Elevation Support Tube 1 5 45 506 507 Elevation Support Tube End Cap 4 5 45 507 508 Elevation Motor 1 5 45 508 509 Elevation Gear Sleeve 1 5 45 509 510 Fold Up Support 1 5 45 510 511 Shock 1 5 45 511 512 Wheel 1 5 45 512 513 Plastic Clamp Top 2 5 45 513 514 Plastic Clamp Bottom 2 5 45 514 515 Elevation Support 2 5 45 515 516 Motor Hood Left 1 5 45 516 517 Motor Hood Right 1 5 45 517 518 Motor Bottom Cover 1 5 45 518 519 Relay board 1 5 45 519 520 Rubber Cushion 2 5 45 520 600 Complete Running Deck Components 601 Running Belt 1 5 45 601 602 Side Rail 2 5 45 602 603 Running Deck 1 5 45 603 604 Side Rail End Cap Left 1 5 45 604 605 Side Rail End Cap Right 1 5 45 605 606 Cushion Pad 8 5 45 606 9 5 45 MOTORIZED TREADMILL s COMPLETE PARTS LIS
33. rranty parts to you and reimburse as described above To help the technician assist you please have the following information ready e Model name or number from the cover of the manual e Serial number located on the frame of the unit e The part description and the order number Limitations on Warranty This Warranty does not cover wear and tear any problems damages or failures that are caused by accident improper assembly failure to observe cautionary labels on the product failure to operate the product correctly abuse or freight damage Smooth Fitness does not warrant against any damage or defects that may result from repair or alterations made to the product by an unauthorized repair facility This Warranty does not apply to any product shipped or handled outside of Germany Austria and England This Warranty does not apply if the product is used as a rental product or in commercial use Consequential and incidental damages are not recoverable under this Warranty THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER EXPRESS WARRANTIES ALL IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE ARE LIMITED IN DURATION TO ONE 1 YEAR FROM THE EFFECTIVE DATE OF THIS WARRANTY SMOOTH FITNESS IS NOT LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES RESULTING FROM ANY DEFECT IN PARTS NOR FOR ANY BREACH OF EXPRESS OR IMPLIED WARRANTIES SMOOTH FITNESS SOLE LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE TERMS
34. rting Transportation instruction on pg 29 5 45 MOTORIZED TREADMILL UNFOLDING INSTRUCTIONS How to unfold the treadmill NOTE To maintain stability make sure the rear transportation wheel is disengaged before unfolding treadmill To unfold the treadmill for use follow the instructions here Release Lever Push the deck towards the computer console Depress the Folding Level begin lowering the treadmill towards the floor release the folding level Lower treadmill deck towards floor 5 45 MOTORIZED TREADMILL TRANSPORT INSTRUCTIONS TRANSPORT INSTRUCTIONS NOTE Transport wheel must be down as picture below To roll away for storage simply grab the rear deck lift slightly and roll to desired location Lift the deck from the rear so that the treadmill rests on the front transportation wheels and on the rear transportation wheel engages Roll to a desired location 5 45 MOTORIZED TREADMILL COMPUTER OPERATION S A BC DEF START Button A B INCLINE UP DOWN Button Safety Key c D SPEED UP DOWN Button STOP ENTER Button E F Display Window BUTTON FUNCTIONS START Press to start exercise at initial speed 0 5MPH 0 8KPH STOP ENTER 1 Press to confirm
35. s at a speed of 2MPH 3 2KPH After the one minute cool down the treadmill will stop and return to P2 start display Press STOP ENTER to go to POWER ON status 5 45 MOTORIZED TREADMILL EEE Computer OPERATION P4 WEIGHT LOSS If you select the P4 WEIGHT LOSS program the upper and lower LCD will show the following After completing the user information set up the SPEED CALORIES and PULSE LCD display O The TIME display shows factory setting 24 00 and the blinking workout load level shows 1 Press the INCLINE UP DOWN buttons to adjust the workout load level from 1 to 12 then press the STOP ENTER button to confirm the setting Then the TIME LCD displays a blinking 24 00 Press the INCLINE UP DOWN buttons to adjust the total workout time and press the STOP ENTER button to confirm the setting Press the START button to start the workout The SPEED and INCLINE follow the pre set workout load chart The TIME counts down from the set up workout time Distance and Calories count up from 0 LEVEL MIN SPEED MAX SPEED MINI INCLINE LEVEL MAX INCLINE LEVEL 1 1 6 2 8 0 3 2 1 8 3 0 0 4 3 2 0 3 2 1 5 4 2 2 3 4 1 6 5 2 4 3 6 2 7 6 2 6 3 8 2 8 7 2 8 4 0 3 9 8 3 0 4 2 3 10 9 3 2 4 4 3 11 During the workout users can overwrite the speed by pressing the SPEED UP DOWN buttons and overwrite the incline level by pressing the INCLINE UP DOWN buttons COOL DOWN After the pre set TIME counts dow
36. s down 3 seconds with 3 short beeps then starts from 0 5 MPH 0 8 KPH Press the SPEED UP DOWN buttons to adjust the speed Press the INCLINE UP DOWN buttons to elevate the treadmill The TIME CALORIES and DISTANCE count up from 0 The PULSE LCD shows P until you hold the hand pulse grip sensors or wear the chest belt heart rate transmitter optional then the PULSE LCD will display the current pulse during the workout STOP PAUSE During the workout press the STOP ENTER button to PAUSE the treadmill all workout data will be frozen Press the START button to resume the workout and all data will continue counting If the STOP ENTER button is pressed twice the treadmill will return to POWER ON status and all workout information will return to 0 COMPUTER PROGRAM OPERATION To select the program press the program buttons when the treadmill is in POWER ON status For the first time user you have to set up the user information and assign your USER ID from U 1 to U 9 before the program starts SET UP USER INFORMATION Press any program button on the computer panel For the first time use of the treadmill the upper LCD will show a blinking U1 and the lower LCD will show factory default setting values of user weight height age and target heart rate Press the INCLINE UP DOWN buttons to choose the USER ID from U1 to U9 and press the STOP ENTER button to assign your user ID SET USER GENDER After assigning your user ID the gender icon will display on
37. sembled make sure there is a comfortable amount of free area around the unit for unobstructed operation Invite a friend Some of the assembly steps may require heavy lifting It is recommended that you obtain the assistance of another person when assembling this product User Weight Limitation Please note that there is a weight limitation for this product If you weigh more than 275LBS It is not recommended that you use this product Serious injury may occur if the user s weight exceeds the limit shown here This product is not intended to support users whose weight exceeds this limit Care and maintenance 1 The safety level can be maintained only if it is examined for damage and wear 2 Replace any defective components immediately and stop all use of equipment until repaired 3 Always take care when you mounting the equipment Straddle the equipment by placing your feet on the straddle rails Dismount from the equipment only after all parts have stopped 4 Always check the easily wear components like pulley etc To prevent danger 5 There is an emergency stop to prevent dangers you can stop the treadmill immediately by actuated the emergency stop for emergency dismount 5 45 MOTORIZED TREADMILL SUPPLIED COMPONENTS This list identifies the major components you will use to assemble this product Component A B and C are already partially assembled No Description Ot
38. t unplug the power cord from the surge protector Using the hex key provided turn both the left and right rear roller adjustment bolts the same distance usually a 1 2 turn in the clockwise direction Plug the power cord back into the surge protector and run the treadmill at 2 5 mph You should now walk on the belt to determine if the belt is still slipping Repeat the above procedure until the walking belt is not slipping The tension should be just tight enough not to slip WARNING Do not over tighten rollers This will cause premature roller bearing failure Right and left tension bolts are located at the rear of the treadmill 5 45 MOTORIZED TREADMILL EEE maintenance CLEANING Routine cleaning of your treadmill will extend the product s life Warning To prevent electrical shock be sure the power to the treadmill is OFF and the power cord is unplugged from the wall electrical outlet before attempting any cleaning or maintenance Important Do not use abrasives or solvents to clean the treadmill To prevent damage to the computer keep liguids away and keep it out of direct sunlight After each workout Wipe off the console and other treadmill surfaces with a clean water dampened soft cloth to remove excess perspiration Weekly Use of a treadmill mat is recommended for ease of cleaning Dirt from your shoes contacts the belt and eventually makes it to underneath the treadmill Vacuum underneath treadmill once a we
39. the lower LCD Press the INCLINE UP DOWN buttons to switch between male and female icon then press the STOP ENTER button to select your gender SET USER WEIGHT After setting the user gender the lower LCD will display W The TIME LCD display now shows the blinking factory setting user weight 150LB 68KG Press the INCLINE UP DOWN buttons to adjust the user weight correctly and press STOP ENTER to set the user weight 5 45 MOTORIZED TREADMILL EE COMPUTER OPERATION SET USER HEIGHT After setting the user weight the lower LCD will display H The CALORIES LCD display now shows the blinking factory setting user height 5 3 160CM Press the INCLINE UP DOWN buttons to adjust the user height correctly and press STOP ENTER to set the user height SET USER AGE After setting the user weight the lower LCD will display A The INCLINE LEVEL LCD display now shows the blinking factory setting user age 35 Press the INCLINE UP DOWN buttons to adjust the user age correctly and press STOP ENTER to set the user age SET USER TARGET HEART RATE When you set up the user AGE please note the user TARGET HEART RATE will be adjusted with the user AGE according to the factory setting The factory TARGET HEART RATE setting is based on 85 of the maximum heart rate The maximum heart rate is calculated as 220 minus the user age For age 35 the maximum user heart rate should be 185 and 85 of user heart rate which is 157 After setting the user age the low
40. ttom 1 5 45 105 106 Safety Key Base 1 5 45 106 107 Safety Key 1 5 45 107 108 Water Bottle Holder 2 5 45 108 110 Plastic Fixing Insert 8 5 45 110 111 Hand Pulse Wire upper 2 5 45 111 200 Complete Handle Bar Components 201 Front Handle Bar Tube 1 5 45 201 202 Handle Bar 2 5 45 202 203 Handle Bar Upright Foam Grip 2 5 45 203 204 Handle Bar Upright Foam Grip 2 5 45 204 205 Handle Bar Upright Foam Grip 1 5 45 205 206 Hand Pulse Sensor 2 5 45 206 207 Handle Bar Cover LL 1 5 45 207 208 Handle Bar Cover LR 1 5 45 208 209 Handle Bar Cover RL 1 5 45 209 210 Handle Bar Cover RR 1 5 45 210 211 Console Connect Piece L 1 5 45 211 212 Console Connect Piece R 1 5 45 212 213 Console Connect Tube 2 5 45 213 216 Handle Bar End Cap 2 5 45 216 217 Hand Pulse Wire Lower 2 5 45 217 300 Complete Upright Components 301 Upright 2 5 45 301 302 Upright Low Cover LL 1 5 45 302 303 Upright Low Cover LR 1 5 45 303 304 Upright Low Cover RL 1 5 45 304 305 Upright Low Cover RR 1 5 45 305 306 Adjustable Cylinder Cover Upper 2 5 45 306 308 2 Pin Safety Key Wire 2200 mm 1 5 45 308 309 7 Pin Computer Wire Upper 2980 mm 1 5 45 309 5 45 MOTORIZED TREADMILL EY MI COMPLETE PARTS LIST Part No Description Oty Order No 400 Complete Base Frame Components 401 Base Frame 1 5 45 401 402 Rubbe
41. y A Main Frame Assembly 1 B Front handlebar 1 A C Side handlebar 2 108 Water Bottle Holder 2 207 Handle Bar Cover LL 1 208 Handle Bar Cover LR 1 209 Handle Bar Cover RL 1 210 Handle Bar Cover RR 1 302 Upright Base Cover LL 1 303 Upright Base Cover LR 1 304 Upright Base Cover RL 1 305 Upright Base Cover RR 1 5 45 MOTORIZED TREADMILL 6 El SUPPLIED HARDWARE This list identifies the hardware you will use to assemble the product To help distinguish between the various types of the screw and bolts use the scale below to measure them and compare them to the size listed No Description ty ar 610 FEN 802 M4x15 Screw 27 805 oly 811 805 M8x45 Bolt 2 f T 310 MBx18 Boh 3 e mm 811 M8x52 Bolt 2 812 8 Washer 12 812 PR P 812 802 845 845 M8x75 Bolt 2 lt Screw Driver 1 X A M O m B Allen Key 1 ASV c Allen Wrench 1 107 Safety Key 1 m ZS B N ER P Cord 1 j E ower Cor B E AP 107 AR E Ke 0 10 30 40 60 70 80 90 100 MILLIMETERS 5 45 MOTORIZED TREADMILL COMPLETE PARTS LIST Part No Description Qty Order No 100 Complete Computer Console Components 101 Overlay 1 5 45 101 102 Computer PC Board 1 5 45 102 103 Console Plate 1 5 45 103 104 Console Housing Upper 1 5 45 104 105 Console Housing Bo
42. y an electrician refer to the Power Reguirements section in this manual Program time has expired Treadmill will not incline Power fold models only Check for proper positioning of spring knob for folding See procedure in owner s manual Treadmill will not unfold Power Fold only Check for proper positioning of spring knob for folding See procedure in owner s manual Manual Fold only Folding locking lever is depressed Treadmill running belt moves slower than speed displayed on computer Metric English conversion See owner s manual for Metric English conversion process Treadmill running belt moves slower than speed displayed on computer Metric English conversion See owner s manual for Metric English conversion process Running belt is not centered Treadmill is properly leveled See procedure in owner s manual Center running belt See Centering procedure in owner s manual Running belt is slipping or hesitating while in use Tension running belt See process in owner s manual Treadmill running belt moves slower than speed displayed on computer Metric English conversion See owner s manual for Metric English conversion process Running belt is not centered Treadmill is properly leveled See procedure in owner s manual Center running belt See Centering procedure in owner s manual Running belt is slipping or hesitating while in use Tension running be
Download Pdf Manuals
Related Search