Smeg AS21T76F Range User Manual
Contents
1. 6 2 Cleaning of cooking hob components The caps and flame spreader crowns are extractable to facilitate cleaning Wash them in hot water with non abrasive detergent taking care to remove any incrustations and wait until they are perfectly dry CAUTION do not wash these components in a dishwasher The burners can be left to soak in hot water ana detergent Replace the flame spreader crowns checking that they are positioned in their housing with their respective caps taking care that flame spreader holes A correspond to the spark plugs and the thermocouples To work well the ignition plugs and thermocouples must always be very clean Check them frequently and clean them with a wet rag if necessary Any dry residue should be gt removed with a toothpick or a needle2. Before lighting the hob burners check that the flame caps are in the correct position and that their burner caps are in place making sure that the holes A in the flame caps correspond to the spark plugs and thermocouples Panstand grid B available upon request is intended for use with woks Chinese pans To prevent damage to the worktop the hob is equipped with a raised grid C installs over pans larger than the diameter shown in the table in paragraph 5 3 Diameter of receptacles Note that pans larger than 30 cm diameter must be used only on the central burner Each knob corresponds to the burner indicated The appliance is equipped with an electric lighting device To light the burners press and turn the knob anticlockwise to the large flame symbol A Keep the knob pressed for about 2 seconds to let the thermocouple heat up If the burner turns off when the knob is released it means that the thermocouple isn t hot enough Repeat ignition and keep the knob pressed longer Once the burner has been ignited the flame can be regulated as required Always check that the control knobs are in the position off when you finish using the hob If the burners turn off accidentally a safety device will trip after about 20 seconds to cut off gas flow even with the gas tap open ose Instructions for the user 5 2 Practical advice for using the burners For better use of the burners and lower gas consumption use cover
3. Use a soapy solution to check for proper tightness Never use a free flame The hob has been inspected for G20 2H natural gas at a pressure of 20 mbar For use with other types of gases see Section 3 ADAPTING TO DIFFERENT TYPES OF GAS The gas intake fitting is 7 gas external threaded ISO 228 1 Connection with rigid copper pipe the connection to the gas mains must not provoke stress of any kind on the hob Connection may be made by using biconical adapter D with insertion of gasket C supplied G Connection with flexible pipe use only flexible pipes conforming to standard regulations in force inserting gasket C supplied between fitting A B and flexible pipe E The flexible pipe has to be installed so that pipe length does not exceed 1 5 meters of maximum extension Make sure that the pipes do not touch any moving parts or become damaged 2 6 Connection to LPG Use a pressure regulator and make the connection to the tank according to the provisions of standards regulations in force Make sure that feed pressure conforms to the levels shown in the table in paragraph 3 2 Burner and nozzle characteristics table Instructions for the installer 3 ADAPTATION TO DIFFERENT TYPES OF GAS Before performing any cleaning or maintenance work detach the appliance from the electrical socket The cooker hob is set for natural gas G20 2H at a pressure of 20 mbar for cookers with maxi oven an
4. DO NOT LEAVE THE PACKING IN THE HOME ENVIRONMENT C O SEPARATE THE VARIOUS WASTE MATERIALS AND TAKE THEM TO THE NEAREST SPECIAL GARBAGE COLLECTION CENTRE _ IT IS OBLIGATORY FOR THE ELECTRICAL SYSTEM TO BE GROUNDED S ACCORDING TO THE METHODS REQUIRED BY SAFETY RULES THE PLUG TO BE CONNECTED TO THE POWER CABLE AND THE Pes SOCKET MUST BE THE SAME TYPE AND MUST CONFORM TO Sr CURRENT REGULATIONS NEVER UNPLUG BY PULLING ON THE CABLE TEST OF THE COOKING HOB FOLLOWING THE INSTRUCTIONS BELOW SHOULD THE APPLIANCE NOT FUNCTION DISCONNECT IT FROM THE SUPPLY AND CALL THE NEAREST TECHNICAL ASSISTANCE CENTRE NEVER ATTEMPT TO REPAIR THE APPLIANCE 1 IMMEDIATELY AFTER INSTALLATION CARRY OUT A BRIEF INSPECTION ALWAYS CHECK THAT THE CONTROL KNOBS ARE IN THE POSITION OR 0 OFF WHEN YOU FINISH USING THE HOB THE IDENTIFICATION PLATE WITH TECHNICAL DATA SERIAL NUMBER AND MARKING IS CLEARLY VISIBLE UNDER THE CASING THE PLATE ON THE CASING MUST NOT BE REMOVED 17 18 Introduction DO NOT PUT PANS WITHOUT PERFECTLY SMOOTH AND FLAT BOTTOMS ON THE COOKING HOB GRIDS DO NOT USE RECIPIENTS OR GRIDDLE PLATES THAT EXTEND BEYOND THE EXTERNAL PERIMETER OF THE HOB THE HOB IS TO BE USED BY ADULTS ONLY DO NOT LET UNSUPERVISED CHILDREN PLAY WITH THE HOB THIS APPLIANCE IS MARKED ACCORDING TO THE EUROPEAN DIRECTIVE 2002 96 EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT WEEE THIS GUIDELINE IS THE FRAME OF A EUROPEAN WIDE VAL
5. which the hob is installed must have sufficient air flow to satisfy the requirements of normal gas combustion and of necessary air exchange in the room The air intakes protected by screens must be appropriately sized regulations in force and placed so as not to be blocked in any way The room where the oven is installed should be suitably ventilated to avoid overheating or excess humidity produced by cooking and in the case of lengthy use a window should be opened or the speed of any ventilators should be increased 2 4 Discharge of combustion products g Discharge of combustion products must be guaranteed by means of hoods connected to a natural draught flue with certain efficiency or by AN means of forced aspiration An efficient aspiration system requires careful planning by a specialist capable of installing it respecting the positions and distances prescribed by standards After installation the installer must issue a certificate of conformity 21 22 Instructions for the installer 2 5 Gas connection Connection to the gas mains may be made with a rigid copper pipe or with a flexible pipe and conforming to the provisions defined by standard regulations in force To facilitate connection fitting A on the rear of the appliance may be adjusted laterally For this purpose loosen hexagon nut B turn fitting A to the desired position and retighten hexagon nut B tightness is ensured by a biconical brass ring
6. Contents 1 INSTRUCTIONS FOR SAFE AND PROPER USE 17 2 INSTALLATION OF THE APPLIANCE 19 3 ADAPTATION TO DIFFERENT TYPES OF GAS 23 4 FINAL OPERATIONS 25 9 USE OF THE COOKING HOB 26 6 CLEANING AND MAINTENANCE 28 THESE INSTRUCTIONS ARE VALID ONLY FOR END USER COUNTRIES WHOSE IDENTIFICATION SYMBOLS APPEAR ON THE COVER OF THIS MANUAL INSTRUCTIONS FOR THE INSTALLER these are for the qualified technician who must carry out a suitable check of the gas system install the appliance set it functioning and carry out an inspection test ome INSTRUCTIONS FOR THE USER these contain user advice description of the commands and the correct procedures for cleaning and maintenance of the appliance Introduction 1 INSTRUCTIONS FOR SAFE AND PROPER USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND BH THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE COOKING HOB WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE USING THE COOKING HOB ALSO KEEP THE SERIES OF NOZZLES SUPPLIED INSTALLATION MUST BE CARRIED OUT BY QUALIFIED PERSONNEL IN ACCORDANCE WITH THE REGULATIONS IN FORCE THIS APPLIANCE IS INTENDED FOR DOMESTIC USES AND CONFORMS TO CURRENT REGULATIONS IN FORCE THE APPLIANCE HAS BEEN BUILT TO CARRY OUT THE FOLLOWING FUNCTIONS COOKING AND HEATING UP OF FOOD ALL OTHER USES ARE CONSIDERED IMPROPER THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR IMPROPER USE
7. IDITY OF RETURN AND RECYCLING ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT The manufacturer declines all responsibility for damage to persons or things caused by non observance of the above prescriptions or by interference with any part of the appliance or by the use of non original spares A JE K 2 FD Instructions for the installer 2 INSTALLATION OF THE APPLIANCE Installation must be carried out by a qualified technician in compliance with applicable regulations in force 2 1 Positioning The following operation requires building and or carpentry work so musi be carried out by a competent tradesman Installation can be carried out on various materials such as masonry metal solid wood or plastic laminated wood as long as they are heat resistant T 90 C 2 1 1 Fixing Insert screws A of the brackets provided into slots B under the appliance Slide the brackets into slots B Position the appliance on to the support frame and secure it by means of screws C To connect the appliance to the mains holes have to be made in the cabinet which vary from model to model The diagram below shows the dimensions of the three models and the distances from the edges at which the hole in grey has to be made in each case Make sure there is a minimum of 750 mm between the hot plate flames and any shelf that may be installed directly above them 19 Instructions for the installer 2 2 Electrical connection Make su
8. d for LPG G30 G31 3 at a pressure of 28 37 mbar for cookers with gas bottle compartments In the case of functioning with other types of gas the burner nozzles must be changed and the minimum flame adjusted on the gas taps To change the nozzles proceed as described below 3 1 Replacement of nozzles on the hob This operation requires no primary air regulation 1 Extract the grids and remove all the caps and flame spreader crowns 2 unscrew the burner nozzles with a 7 mm socket wrench 3 replace the nozzles according to the type of gas to be used and the description in paragraph 3 2 Burner and nozzle characteristics table 4 Replace the burners in the correct position 23 Instructions for the installer X 3 2 Burner and nozzle characteristics table Rated Burner heating LPG G30 G31 28 37 mbar capacity kW Nozzle By pass Reduced Flowrate Flowrate diameter mm flowrate g h G30 g h G31 1 100 mm 1 100 W Auxiliary 1 05 50 30 360 76 75 Semi rapid 1 8 65 33 450 131 129 Rapid 3 85 45 800 218 215 Ultrarapid 3 3 91 65 1600 240 236 Rated Burner heating Natural gas G20 20 mbar capacity kW Nozzle diameter Reduced flowrate 1 100 mm W Auxiliary 1 05 72 360 Semi rapid 1 8 97 450 Rapid 3 115 800 Ultrarapid 9 5 133 1600 3 3 Arrangement of burners on cooking hob BURNERS 1 Auxiliary 2 Semi rapid 3 Rapid 4 Ultrarapid 24 Instructions for the installer 4 FINAL OPERATIONS Having carried ou
9. ed ext containers that are proportional in size to the burner to prevent the flame Wd from licking the sides see paragraph 5 3 Diameter of containers When water reaches the boiling point lower the flame so that it doesn t overflow To avoid burns or damage to the hob all recipients or griddle plates must be placed within the perimeter of the cooking hob When using fats or oils be extremely careful that they don t overheat and catch fire 5 3 Diameter of containers BURNERS min and max in cm 1 Auxiliary 12 14 2 Semi rapid 16 20 3 Rapid 18 24 4 Ultrarapid 20 24 5 Ultrarapid 20 26 27 28 Instructions for the user ome 6 CLEANING AND MAINTENANCE Before any intervention disconnect the power supply of the device 6 1 Cleaning stainless steel To keep stainless steel in good condition it should be cleaned regularly after use Let it cool first 6 1 1 Ordinary Daily Cleaning To clean and preserve the stainless steel surfaces always use only specific products that do not contain abrasives or chlorine based acids How to use pour the product on a damp cloth and wipe the surface rinse thoroughly and dry with a soft cloth or deerskin 6 1 2 Food stains or residues Do not use metallic sponges or sharp scrapers they will damage the surface Use normal non abrasive products for steel and a wooden or plastic tool if necessary 7 4 Rinse thoroughly and dry with a soft cloth or deerskin zu
10. re that the voltage and capacity of the power line conform to the CE data shown on the plate located under the casing Do not remove this 20 plate for any reason The plug on the end of the supply cable and the wall socket must be the same type and conform to the current electrical system regulations Check that the power line is adequately grounded On the power line install an omnipolar cut off device with contact cut off distance greater than or equal to 3 mm located in an easily accessible position near the unit Do not use reducers adapters or shunts If the power cable is replaced the wire section on the new cable must not be less than 0 75 mm 3 x 0 75 cable keeping in mind that the end to be connected to the hob must have the ground wire yellow green longer by at least 20 mm Use only H05V2V2 F cable or similar which has a maximum temperature of 90 C Any replacement needed should be carried out by a specialised technician who should make the mains connections according to the following diagram L brown N blue yellow green The manufacturer will not be liable for any damage to persons or property caused by non observance of the above instructions or deriving from the tampering of even a single part of the hob Instructions for the installer 2 3 Ventilation of rooms ea The hob may be installed only in rooms with permanent ventilation as Ph required by standards regulations in force The room in
11. t the above adjustments reassemble the appliance following backwards the instructions in paragraph 3 2 Burner and nozzle characteristics table After adjustment to a different kind of gas from the one for which the cooker has been tested replace the plate inside the heating compartment with one corresponding to the new kind of gas This plate can be obtained from your nearest Authorised Assistance Centre 4 1 Adjustment of minimum for natural gas Light the burner and take it to the minimum Remove the gas tap knob and turn the I adjustment screw inside or at the side of the tap shaft depending on the model until there is a regular minimum flame Replace the knob and Ios check burner flame stability rapidly turning the C UJ knob from maximum to minimum position the v flame should not go out Repeat the operation on URN all the gas taps 4 2 Regulation of minimum for LPG To regulate the minimum for LPG completely tighten clockwise the screw inside or next to the gas tap pin depending on the model The diameters of the by passes for each burner are given in table 3 2 Burner and nozzle characteristics table 4 3 Lubrication of gas taps With time it may happen that the gas taps get blocked and hard to turn Clean them inside and re grease them This operation must be done by a specialised technician 25 NA A 26 Instructions for the user Cd 5 USE OF THE COOKING HOB 5 1 Lighting the burners
Download Pdf Manuals
Related Search